1N5338B
THRU
1N5369B
5 Watt
Zener Diode
5.1 to 51 Volts
Features
xZener Voltage From 5.1V to 51V
x Operating Temperature: -55qC to +150qC
x Storage Temperature: -55qC to +150qC
x 5 Watt DC Power Dissipation
x Maximum Forward Voltage @ 1A: 1.2 Volts
x Power Derating: 40 mW/к Above 75к
Mechanical Data
Case: JEDEC DO-15.
Terminals: Solder plated , solderable per MIL-STD-750,
Method 2026.
Standard Packaging: 52mm tape
DO-15
A
B
C
D
D
Cathode
Mark
omponents
20736 Marilla Street Chatsworth

 !"#
$%  !"#
MCC
Revision: A 2011/01/01
TM
Micro Commercial Components
DIMENSIONS
INCHES MM
DIM MIN MAX MIN MAX NOTE
A .230 .300 5.80 7.60
B .104 .140 2.60 3.60
C .026 .034 .70 .90
D 1.000 --- 25.40 ---
Marking : Cathode band and type number
www.mccsemi.com
1 of 6
x Maximum thermal resistence: 25C/W from junction to ambient
Maximum Ratings:
Lead Free Finish/RoHS Compliant (Note1) ("P"Suffix designates
Compliant. See ordering information)
Note: 1. High Temperature Solder Exemption Applied, see EU Directive Annex 7.
Epoxy meets UL 94 V-0 flammability rating
Moisture Sensitivity Level 1
1N53
3
8B
T
H
RU 1N
5
3
6
9B
ELECTRICAL CHARACTERISTICS
(
TA=25 unless otherwise noted, VF=1.2 Max
@
IF=
1
A
f
o
r
a
ll t
y
p
es
)
.
NOTE:
1. TOLERANCE AND VOLTAGE DESIGNATION - The JEDEC type numbers shown indicate a tolerance of+/-10% with
guaranteed limits on only Vz, IR,I
r, and VFas shown in the electrical characteristics table. Units with guaranteed limits
on all seven parameters are indicated by suffix B for+/-5% tolerance.
2. ZENER VOLTAGE (Vz) AND IMPEDANCE (ZZT &Z
ZK) - Test conditions for Zener voltage and impedance are as
follows; Iz is applied 40+/-10 ms prior to reading. Mounting contacts are located from the inside edge of mounting
clips to the body of the diode(Ta=25 )
MCC PART
NUMBER
REGULATOR
VOLTAGE
VZ
TEST
CURRENT
IZT
MAXIMUM
DYNAMIC
IMPEDANCE
ZZk(@IZT)
MAXIMUM
REVERSE
CURRENT
IR
TEST
VOLTAGE
VR
MAXIMUM
REGULATOR
CURRENT
IZM
MAXIMUM
DYNAMIC
KNEE
IMPEDANCE
ZZK@ 1.0mA
MAXIMUM
SURGE
CURRENT
Ir
MAXIMUM
VOLTAGE
REGULATION
VOLTS mA OHMS PAVOLTS mA ohms AVOLTS
1N5339B 5.6 220 1.0 1.0 2.0 865 400 13.4 0.25
1N5340B 6.0 200 1.0 1.0 3.0 790 300 12.7 0.19
1N5341B 6.2 200 1.0 1.0 3.0 765 200 12.4 0.10
1N5342B 6.8 175 1.0 10 5.2 700 200 11.5 0.15
1N5343B 7.5 175 1.5 10 5.7 630 200 10.7 0.15
1N5344B 8.2 150 1.5 10 6.2 580 200 10 0.20
1N5345B 8.7 150 2.0 10 6.6 545 200 9.5 0.20
1N5346B 9.1 150 2.0 7.5 6.9 520 150 9.2 0.22
1N5347B 10 125 2.0 5.0 7.6 475 125 8.6 0.22
1N5348B 11 125 2.5 5.0 8.4 430 125 8.0 0.25
1N5349B 12 100 2.5 2.0 9.1 395 125 7.5 0.25
1N5350B 13 100 2.5 1.0 9.9 365 100 7.0 0.25
1N5351B 14 100 2.5 1.0 10.6 340 75 6.7 0.25
1N5352B 15 75 2.5 1.0 11.5 315 75 6.3 0.25
1N5353B 16 75 2.5 1.0 12.2 295 75 6.0 0.30
1N5354B 17 70 2.5 0.5 12.9 280 75 5.8 0.35
1N5355B 18 65 2.5 0.5 13.7 264 75 5.5 0.40
1N5356B 19 65 3.0 0.5 14.4 250 75 5.3 .040
1N5357B 20 65 3.0 0.5 15.2 237 75 5.1 .040
1N5358B 22 50 3.5 0.5 16.7 216 75 4.7 0.45
1N5359B 24 50 3.5 0.5 18.2 198 100 4.4 0.55
1N5360B 25 50 4.0 0.5 19 190 110 4.3 0.55
1N5361B 27 50 5.0 0.5 20.6 176 120 4.1 0.60
1N5362B 28 50 6.0 0.5 21.2 170 130 3.9 0.60
1N5363B 30 40 8.0 0.5 22.8 158 140 3.7 0.60
1N5364B 33 40 10 0.5 25.1 144 150 3.5 0.60
1N5365B 36 30 11 0.5 27.4 132 160 3.3 0.65
1N5366B 39 30 14 0.5 29.7 122 170 3.1 0.65
1N5367B 43 30 20 0.5 32.7 110 190 2.8 0.70
1N5368B 47 25 25 0.5 35.8 100 210 2.7 0.80
1N5369B 51 25 27 0.5 38.8 93 230 2.5 0.90
qC
qC
(Note2) (Note2) (Note2) (Note3)(Note5) (Note4)
MC
C
1N5338B5.1 2401.51.0 1.0 930 400 14.4 0.39
Revision: A 2011/01/01
www.mccsemi.com
2 of 6
Micro Commercial Components
TM
3. SURGE CURRENT (Ir) - Surge current is specified as the maximum allowable peak, non-recurrent square-wave
current with a pulse width, PW, of 8.3 ms. The data given in Figure 5 may be used to find the maximum surge
current for a quare wave of any pulse width between 1 ms and 1000ms by plotting the applicable points on
logarithmic paper. Examples of this, using the 6.8v , is shown in Figure 6. Mounting
contact located as specified in Note 3. (TA=25 ).
4. VOLTAGE REGULATION (Vz) - Test conditions for voltage regulation are as follows: Vz measurements are made
at 10% and then at 50% of the Iz max value listed in the electrical characteristics table. The test currents are the
same for the 5% and 10% tolerance devices. The test current time druation for each Vz measurement is 40+/- 10 ms.
(T
A=25C ). Mounting contact located as specified in Note2.
5. MAXIMUM REGULATOR CURRENT (IZM) - The maximum current shown is based on the maximum voltage of a
5% type unit. Therefore, it applies only to the B-suffix device. The actual IZM for any device may not exceed the
value of 5 watts divided by the actual Vz of the device. TL=75Cat maximum from the device body.
APPLICATION NOTE:
1N53
3
8B
T
H
RU 1N
5
3
6
9B
MCC
Revision: A 2011/01/01
TM
Micro Commercial Components
ć
www.mccsemi.com
3 of 6
Since the actual voltage available from a given Zener
diode is temperature dependent, it is necessary to determine
junction temperature under any set of operating conditions
in order to calculate its value. The following procedure is
recommended:
Lead Temperature, TL, should be determined from:
TL = qLA PD + TA
qLA is the lead‐to‐ambient thermal resistance and PD is the
power dissipation.
Junction Temperature, TJ, may be found from:
TJ = TL + DTJL
DTJL is the increase in junction temperature above the lead
temperature and may be found from Figure 4 for a train of
power pulses or from Figure 1 for dc power.
DTJL = qJL PD
For worst‐case design, using expected limits of IZ, limits
of PD and the extremes of TJ (DTJ) may be estimated.
Changes in voltage, VZ, can then be found from:
DV = qVZ DTJ
qVZ, the Zener voltage temperature coefficient, is found
from Figures 2 and 3.
Under high power‐pulse operation, the Zener voltage will
vary with time and may also be affected significantly by the
zener resistance. For best regulation, keep current
excursions as low as possible.
Data of Figure 4 should not be used to compute surge
capability. Surge limitations are given in Figure 5. They are
lower than would be expected by considering only junction
temperature, as current crowding effects cause temperatures
to be extremely high in small spots resulting in device
degradation should the limits of Figure 5 be exceeded.
RATING AND CHARACTERISTICS CURVES
1N5338B THRU 1N5369B
TEMPERATURE COEFFICIENTS
8
6
4
2
0
0 20 40 60 80 100 120
TL, LEAD TEMPERATURE
300
200
100
50
30
20
10
5
0 20 40 60 80 100 120 140 160 180 200 22
0
RANGE
VZ, ZENER VOLTAGE
@
IZT
VOLTS
Fig. 1-POWER TEMPERATURE DERATING CURVE Fig. 2-TEMPERATURE COEFFICIENT-RANGE FOR UNITS
6TO51VOLTS
40
30
20
10
0
0 0.2
0.4 0.6 0 .8 1
MOUNT ON 8.0mm
COPPER PADS TO
EACH TERMINAL
L, LEAD LENGTH TO HEAT SINK
INCH
40
20
10
4
2
1
0.4
0.2
0.1
3 4 6 8 10 20 30 40 60 80 100 200
PW = 1ms*
PW = 8.3ms*
PW = 1000ms*
SINE / SQUARE WAVE PW = 100ms*
NOMINAL VZ
(
V
Fig. 4-TYPICAL THERMAL RESISTANCE Fig. 5-MAXIMUM NON-REPETITIVE SURGE
CURRENT VERSUS NOMINAL ZENER
VOLTAGE (SEE NOTE 3)
PD, MAXIUMU POWER DISSIPATION (WATTS)
JL, JUNCTION-TO -LEAD THERMAL
RESISTANCE (C/W)
IR, PEAK SURGE CURRENT (AMPS)
MCC
Revision: A 2011/01/01
TM
Micro Commercial Components
2
www.mccsemi.com
4 of 6
θVZ, TEMPERATURE COEFFICIENT
(mV/°C) @ I ZT
θJL (t, D), TRANSIENT THERMAL RESISTANCE
JUNCTION‐TO‐LEAD (°C/W)
20
10
5
2
1
0.5
0.2
0.001 0.005 0.01 0.05 0.1 0.5 1 5 10 20 50 100
D = 0.5
D = 0.2
D = 0.1
D = 0.05
D = 0.01
D = 0
NOTE: BELOW 0.1 SECOND, THERMAL
NOTE: RESPONSE CURVE IS APPLICABLE
NOTE: TO ANY LEAD LENGTH (L).
DUTY CYCLE, D = t1/t2
SINGLE PULSE D TJL = qJL(t)PPK
REPETITIVE PULSES D TJL = qJL(t, D)PPK
PPK t1
t2
t, TIME (SECONDS)
Figure 3. Typical Thermal Response
L, Lead Length = 3/8 Inch
RATING AND CHARACTERISTICS CURVES
1N5338B THRU 1N5369B
ZENER VOLTAGE VERSUS ZENER CURRENT
(FIGURES 7,8)
30
20
10
5
2
1
0.5
0.2
0.1
1 10 100 1000
VZ = 6.8V
PLOTTED FROM INFORMATION
GIVEN IN FIGURE 5
1000
100
10
1
0.1
12345678910
T=25
TC=25
VZ
,
ZENER VOLTAGE
(
VOLTS
)
Fig. 6-PEAK SURGE CURRENT VERSUS PULSE
WIDTH(SEE NOTE 3)
Fig. 7-ZENER VOLTAGE VERSUS ZENER CURRENT
VZ = 6.8 THRU 10 VOLTS
1000
100
10
1
0.1
10 20 30 40 50 60
70 80
T=25
VZ, ZENER VOLTAGE
VOLTS
Fig. 8-ZENER VOLTAGE VERSUS ZENER CURRENT
VZ = 11 THRU 51 VOLTS
*** Data of Figure 3 should not be used to compute surge capability. Surge limitations are given in Figure 5. They are
lower than would be expected by considering only junction temperature, as current crowding effects cause
temperatures to be extremely high in small spots resulting in device degradation should the limits of Figure. 5 be
exceeded
IZ, ZENER CURRENT (mA)
IZ, ZENER CURRENT (mA)
Revision: A 2011/01/01
MC
C
Micro Commercial Components
TM
www.mccsemi.com
5 of 6
Ir, PEAK SURGE CURRENT (AMPS)
MCC
Revision: A 2011/01/01
TM
Micro Commercial Components
www.mccsemi.com
6 of 6
3
Device Packing
Part Number-TP Tape&Reel: 4Kpcs/Reel
Part Number-AP Ammo Packing: 3Kpcs/Ammo Box
Part Number-BP Bulk: 25Kpcs/Carton
Ordering Information :
***IMPORTANT NOTICE***
Micro Commercial Components Corp. reserves the right to make changes without further notice to any product herein to
make corrections, modifications , enhancements , improvements , or other changes . Micro Commercial Components
Corp . does not assume any liability arising out of the application or use of any product described herein; neither does it
convey any license under its patent rights ,nor the rights of others . The user of products in such applications shall assume all
risks of such use and will agree to hold Micro Commercial Components Corp . and all the companies whose products are
represented on our website, harmless against all damages.
***LIFE SUPPORT***
MCC's products are not authorized for use as critical components in life support devices or systems without the express written
approval of Micro Commercial Components Corporation.
***CUSTOMER AWARENESS***
Counterfeiting of semiconductor parts is a growing problem in the industry. Micro Commercial Components (MCC) is taking
strong measures to protect ourselves and our customers from the proliferation of counterfeit parts. MCC strongly encourages
customers to purchase MCC parts either directly from MCC or from Authorized MCC Distributors who are listed by country on
our web page cited below. Products customers buy either from MCC directly or from Authorized MCC Distributors are genuine
parts, have full traceability, meet MCC's quality standards for handling and storage. MCC will not provide any warranty
coverage or other assistance for parts bought from Unauthorized Sources. MCC is committed to combat this global
problem and encourage our customers to do their part in stopping this practice by buying direct or from authorized
distributors.