S Cc REV. REVISION CHANGES ECN AO | __AS DRAWN = tewart onnector Al ADDED TEMP. RANGE 5291 IMMA 11118 Susquehanna Trail South Glen Rock, PA 17327-9199 http: //www.stewartconnector.com (717) 235-7512 Fax: (717) 235-7954 PART NO. SS7188SAPG4BA-A403 (30 ulN GOLD) PART NO. SS-7188SAPG4BA-50-A403 (50 ulN GOLD) CAT 5 JACK EIGHT CONTACT, EIGHT POSITION, SHIELDED JACK EMIRF] ONE PIECE SHIELDED, ESD GROUNDED *"-PG4" DESIGNATES INCLUSION OF ALL LEFT AND RIGHT SIDE PANEL GROUNDS "BA DESIGNATES INCLUSION OF ALL TOP AND BOTTOM PANEL GROUNDS, WITH NO REAR SOLDER TAILS AND ALL SIDE SOLDER TAILS. "A403" DESIGNATES DIAMOND STYLE POSTS & EXTENDED TEMPERATURE MATERIAL TO WITHSTAND A TEMPERATURE OF 220 C 708 [17.98 +*.635 [16.13] MAX. +- .850 [21.59] MAX.1 148 [3.75] HIGHEST POINT lJ 7 125 [3.18}.010 [0.25] 032 [0.81] +.005 [.13] 107 [2.72] +.005 [.13] a ws Ss = "3 a a B + ~-- S Ee a iT { { [ | ice | | 040 [1.02 OF BEAM = |+-.425 [10.79] [02] 050 [1.27] TYP TOL NON-ACCUM = 025 [0.64] a 8 100 [254] 1P 3 is 9.035 [0.89] (8) TOL NON-ACCUM | = Sy z NOTES: 9.062 [1.57] (2) aaa ane f MEETS CATEGORY 5 SPECIFICATION > ry _ t AS TESTED PER TIA/EIA 568A. ZN AN TOLERANCE COMPLY WITH F.C.C. DIMENSION REQUIREMENTS f f ALL OTHERS +.005 [0.13] UNLESS OTHERWISE SPECIFIED. a 128 [3.25] 8 DIMENSIONS SHOWN WITH * TO BE CENTRAL #125 [3.18] (2) L450 [11.43] = ABOUT CENTER LINE -- #610 [15.49] ~] 5 AVAILABLE. WITH: P.C.B. RECOMMENDED HOLE LAYOUT SEEN FROM COMPONENT SIDE LOADED 1 8 CONTACTS SHEET 1 OF 2 TOLERANCE 4.003 [0.08] UNLESS OTHERWISE SPECIFIED THIS DRAWING AND THE SUBJECT MATTER SHOWN THEREON | THIRD ANGLE PROJECTION |" 8 T. R. MECKLEY DATE 403-01 _ | ORBNAL PROPOSAL DRAWN ARE CONFIDENTIAL AND THE PROPRIETARY PROPERTY OF CKD BY: DATE EWR NOMEER STEWART CONNECTOR ("SCS") AND SHALL NOT BE BOB COLANTUONO 104-01 REPRODUCED, COPIED OR USED IN ANY MANNER WITHOUT f=} APPD BY: TR MECKLEY DATE 49-5-01 | ETO PRIOR WRITTEN CONSENT OF "SCS". THE SUBJECT MATIER UNLESS OTHERWISE SPECIFIED | DWG NO. REV. MAY BE PATENTED OR A PATENT MAY BE PENDING. SCS TOLERANCES ARE +.005 [0.13] CT/10100 Al AStewart Connector VIIIIIISSSS http: //www.stewartconnector.com 11118 Susquehanna Trail South Glen Rock, PA 17327-9199 (717) 235-7512 Fax: (717) 235-7954 REVISION CHANGES ECN AO AS DRAWN PART NO. SS7188SAPG4BA-A403 (30 ulN GOLD) PART NO. SS-7188SAPG4BA-50-A403 (50 ulN GOLD) 1300 # POINT OF CONTACT 1200 7 WITH PANEL _ 1100 Y ~| 1.080 [2.03] i 1000 / a 2 900 / XL S 800 b = > _ = S 700 [ = N\ 500 / eo lug I g ester a 500 _ - / .275 [6.99] MAX. Le S 400 WZ = 300 / THE SUGGESTED PANEL OPENING IS INTENDED 5 on TO GIVE THE USER THE ABILITY TO HAVE v REASONABLE JACK / PANEL CLEARANCES 100 YET MAINTAIN RELIABLE GROUNDING CAPABILITY. THESE VARIABLES CAN BE Se. on S ADJUSTED IN EITHER DIRECTION BUT MAY Ssegssasg CARRY SOME CONSEQUENCES IN THE FORM HFoFag ror vo OF LOWER MATING FORCES OR TIGHTER PANEL GROUNDING BEAM DEFLECTION S.0.5. = SUGGESTED OPENING SIZE SUGGESTED PANEL OPENING ASSEMBLY TOLERANCES. FORCE VALUES ON THE GRAPH ARE GENERAL AVERAGES TAKEN AT THE POINT OF CONTACT SHOWN ABOVE. THE SUGGESTED PANEL OPENING INCLUDES APPROXIMATELY .020 CLEARANCE ON THE SIDES AND TOP AND .013 ON THE BOTTOM, AT PANEL OPENING. .010 [0.25] MAX. RADIUS (4) SHEET 2 OF 2 pou [0.00] (TOP OF PCB TO BOTTOM OF OPENING) zi THIS DRAWING AND THE SUBJECT MATTER SHOWN THEREON ARE CONFIDENTIAL AND THE PROPRIETARY PROPERTY OF STEWART CONNECTOR ("SCS") AND SHALL NOT BE REPRODUCED, COPIED OR USED IN ANY MANNER WITHOUT PRIOR WRITTEN CONSENT OF SCS. THE SUBUECT MATTER MAY BE PATENTED OR A PATENT MAY BE PENDING. SCS THIRD ANGLE PROJECTION |8 8 7. R. MECKLEY DATE 40-301 _| SNA PROPOSAL DRANG cx BY: BOB COLANTUONO DATE 49-4-01 | FRMMAR _ } f=} mPOBe TR MECKLEY DAE 495-0) [RETO TOLERANCES ARE $005 [2015] | CT710100 RY ad