PCM1741EG4 - Texas Instruments - Datasheet.Directory

+3.3V Single-Supply, 24-Bit, 96kHz Sampling

Enhanced Multilevel, Delta-Sigma, Audio

DIGITAL-TO-ANALOG CONVERTER

PCM1741

DESCRIPTION

The PCM1741 is a CMOS, monolithic, integrated circuit

which includes stereo Digital-to-Analog Converters

(DACs) and support circuitry in a small SSOP-16 package.

The data converters utilize Texas Instrument’s enhanced

multilevel delta-sigma architecture that employs fourth-

order noise shaping and 8-level amplitude quantization to

achieve excellent dynamic performance and improved toler-

ance to clock jitter. The PCM1741 accepts industry standard

audio data formats with 16- to 24-bit data, providing easy

interfacing to audio DSP and decoder chips. Sampling rates

up to 100kHz are supported. A full set of user-program-

mable functions are accessible through a 3-wire serial

control port that supports register write functions.

FEATURES

●

24-BIT RESOLUTION

●

ANALOG PERFORMANCE (VCC = +3.3V):

Dynamic Range: 98dB typ

SNR: 98dB typ

THD+N: 0.005% typ

Full-Scale Output: 2.05Vp-p typ

●

8x OVERSAMPLING DIGITAL FILTER:

Stopband Attenuation: –55dB

Passband Ripple: ±0.03dB

●

SAMPLING FREQUENCY: 5kHz to 100kHz

●

SYSTEM CLOCK: 256, 384, 512, 768fS with

Auto Detect

●

ACCEPTS 16-, 18-, 20-, AND 24-BIT AUDIO

DATA

●

DATA FORMATS: Standard, I2S, and Left-

Justified

●USER-PROGRAMMABLE MODE CONTROLS:

Digital Attenuation: 0dB to –63dB, 0.5dB/Step

Digital De-Emphasis

Digital Filter Roll-Off: Sharp or Slow

Soft Mute

Zero Flags for Each Output

●

3.3V SINGLE POWER SUPPLY

●

5V TOLERANT DIGITAL INPUTS

●

SMALL SSOP-16 PACKAGE

www.ti.com

APPLICATIONS

●AV RECEIVERS

●DVD MOVIE PLAYERS

●DVD ADD-ON CARDS FOR HIGH-END PCs

●HDTV RECEIVERS

●CAR AUDIO SYSTEMS

●OTHER APPLICATIONS REQUIRING 24-BIT

AUDIO

PCM1741

2SBAS175

SPECIFICATIONS

All specifications at TA = +25°C, VCC = 5.0V, VDD = 3.3V, fS = 44.1kHz, system clock = 384fS, and 24-bit data, unless otherwise noted.

PCM1741E

PARAMETER CONDITIONS MIN TYP MAX UNITS

RESOLUTION 24 Bits

DATA FORMAT

Audio Data Interface Formats Standard, I2S, Left-Justified

Audio Data Bit Length 16-, 18-, 20-, 24-Bits Selectable

Audio Data Format MSB-First, Binary Two’s Complement

Sampling Frequency (fS)5 100 kHz

System Clock Frequency 256, 384, 512, 768fS

DIGITAL INPUT/OUTPUT

Logic Family TTL-Compatible

Input Logic Level

VIH 2.0 VDC

VIL 0.8 VDC

Input Logic Current

IIH(1) VIN = VDD 10 µA

IIL(1) VIN = 0V –10 µA

IIH(2) VIN = VDD 65 100 µA

IIL(2) VIN = 0V –10 µA

Output Logic Level

VOH(3) IOH = –2mA 2.4 VDC

VOL(3) IOL = +2mA 1.0 VDC

DYNAMIC PERFORMANCE(4)

PCM1741E

THD+N at VOUT = 0dB fS = 44.1kHz 0.005 0.01 %

fS = 96kHz 0.007 %

THD+N at VOUT = –60dB fS = 44.1kHz 1.6 %

fS = 96kHz 2.0 %

Dynamic Range EIAJ, A-Weighted, fS = 44.1kHz 92 98 dB

A-Weighted, fS = 96kHz 96 dB

Signal-to-Noise Ratio EIAJ, A-Weighted, fS = 44.1kHz 92 98 dB

A-Weighted, fS = 96kHz 96 dB

Channel Separation fS = 44.1kHz 90 96 dB

fS = 96kHz 94 dB

Level Linearity Error VOUT = –90dB ±0.5 dB

DC ACCURACY

Gain Error ±1.0 ±6 % of FSR

Gain Mismatch, Channel-to-Channel ±1.0 ±3 % of FSR

Bipolar Zero Error VOUT = 0.5 VCC at Bipolar Zero ±30 ±60 mV

ANALOG OUTPUT

Output Voltage Full Scale (0dB) 62% of VCC Vp-p

Center Voltage 50% of VCC VDC

Load Impedance AC Load 5 kΩ

DIGITAL FILTER PERFORMANCE

Filter Characteristics 1, Sharp Roll-Off

Passband ±0.03dB 0.454fS

Passband –3dB 0.487fS

Stopband 0.546fSdB

Passband Ripple ±0.03 dB

Stopband Attenuation Stopband = 0.546fS–50 dB

Stopband Attenuation Stopband = 0.567fS–55

Filter Characteristics 2, Slow Roll-Off

Passband ±0.5dB 0.198fS

Passband –3dB 0.390fS

Stopband 0.884fS

Passband Ripple ±0.5 dB

Stopband Attenuation Stopband = 0.884fS–40 dB

Delay Time 20/fSsec

De-Emphasis Error ±0.1 dB

PCM1741 3

SBAS175

ANALOG FILTER PERFORMANCE

Frequency Response f = 20kHz –0.03 dB

f = 44kHz –0.20 dB

POWER SUPPLY REQUIREMENTS(4)

Voltage Range, VDD +2.7 +3.3 +3.6 VDC

VCC +2.7 +3.0 +3.6 VDC

Supply Current, IDD fS = 44.1kHz 6.0 10 mA

fS = 96kHz 13.0 mA

ICC fS = 44.1kHz 7.0 11 mA

fS = 96kHz 7.0 mA

Power Dissipation fS = 44.1kHz 43 88 mW

fS = 96kHz 66 mW

TEMPERATURE RANGE

Operation Temperature –25 +85 °C

Thermal Resistance

JA SSOP-16 115 °C/W

NOTES: (1) Pins 1, 2, 3, 16 (SCK, BCK, LRCK, DATA). (2) Pins 13-15 (MD, MC, ML). (3) Pins 11, 12 (ZEROR, ZEROL). (4) Analog performance specifications

are tested with a Shibasoku #725 THD Meter with 400Hz HPF on, 30kHz LPF on, and an average mode with 20kHz bandwidth limiting. The load connected

to the analog output is 5kΩ or larger, via capacitive coupling.

SPECIFICATIONS (Cont.)

All specifications at TA = +25°C, VCC = 5.0V, VDD = 3.3V, system clock = 384fS (fS = 44.1kHz), and 24-bit data, unless otherwise noted.

PCM1741E

PARAMETER CONDITIONS MIN TYP MAX UNITS

ELECTROSTATIC

DISCHARGE SENSITIVITY

This integrated circuit can be damaged by ESD. Burr-Brown

recommends that all integrated circuits be handled with

appropriate precautions. Failure to observe proper handling

and installation procedures can cause damage.

ESD damage can range from subtle performance degradation

to complete device failure. Precision integrated circuits may

be more susceptible to damage because very small parametric

changes could cause the device not to meet its published

specifications.

Power Supply Voltage, VDD .............................................................. +4.0V

VCC .............................................................. +6.5V

Ground Voltage Differences.............................................................. ±0.1V

Digital Input Voltage................................................–0.3V to (6.5V + 0.3V)

Input Current (except power supply)............................................... ±10mA

Ambient Temperature Under Bias .................................. –40°C to +125°C

Storage Temperature...................................................... –55°C to +150°C

Junction Temperature .................................................................... +150°C

Lead Temperature (soldering, 5s)................................................. +260°C

Package Temperature (IR reflow, 10s) .......................................... +235°C

ABSOLUTE MAXIMUM RATINGS

PACKAGE SPECIFIED

DRAWING TEMPERATURE PACKAGE ORDERING TRANSPORT

PRODUCT PACKAGE NUMBER RANGE MARKING NUMBER(1) MEDIA

PCM1741E SSOP-16 322 –25°C to +85°C PCM1741E PCM1741E Rails

"""""PCM1741E/2K Tape and Reel

NOTE: (1) Models with a slash ( /) are available only in Tape and Reel in the quantities indicated (e.g., /2K indicates 2000 devices per reel). Ordering 2000 pieces

of “PCM1741E/2K” will yield a single 2000-piece Tape and Reel.

PACKAGE/ORDERING INFORMATION

PCM1741

4SBAS175

BLOCK DIAGRAM

PIN ASSIGNMENTS

PIN NAME TYPE FUNCTION

1 BCK IN Audio Data Bit Clock Input.(1)

2 DATA IN Audio Data Digital Input.(1)

3 LRCK IN L-Channel and R-Channel Audio Data Latch En-

able Input.(1)

4 DGND – Digital Ground

DD – Digital Power Supply, +3.3V

CC – Analog Power Supply, +3.3V

OUTL OUT Analog Output for L-Channel.

OUTR OUT Analog Output for R-Channel.

9 AGND – Analog Ground

10 VCOM – Common Voltage Decoupling.

11 ZEROR/ OUT Zero Flag Output for R-Channel/Zero Flag Output

ZEROA for L/R-Channel.

ZEROL/NA

OUT Zero Flag Output for L-Channel/No Assign.

13 MD IN Mode Control Data Input.(2)

14 MC IN Mode Control Clock Input.(2)

15 ML IN Mode Control Latch Input.(2)

16 SCK IN System Clock Input.

NOTES: (1) Schmitt-trigger input, 5V tolerant. (2) Schmitt-trigger with internal

pull-down, 5V tolerant.

PIN CONFIGURATION

TOP VIEW SSOP

Audio

Serial

Port

Output Amp and

Low-Pass Filter

DAC

Oversampling

Digital Filter

with

Function

Controller

Enhanced

Multilevel

Delta-Sigma

Modulator

Output Amp and

Low-Pass Filter

DAC

BCK

LRCK

DATA

Serial

Control

Port

System Clock

Manager

Zero Detect Power Supply

OUT

COM

OUT

DGND

ZEROL

ZEROR

SCK

System Clock

AGND

BCK

DATA

LRCK

DGND

OUT

SCK

ZEROL/NA

ZEROR/ZEROA

COM

AGND

PCM1741

PCM1741 5

SBAS175

TYPICAL PERFORMANCE CURVES

All specifications at TA = +25°C, VCC = VDD = 3.3V, system clock = 384fS (fS = 44.1kHz), and 24-bit input data, unless otherwise noted.

DIGITAL FILTER

Digital Filter (De-Emphasis Off

–1

–2

–3

–4

–5

TRANSITION CHARACTERISTICS (Slow Roll-Off)

0 0.1 0.2 0.3 0.4 0.5

Frequency (x f

)

Amplitude (dB)

–20

–40

–60

–80

–100

–120

–140

FREQUENCY RESPONSE (Sharp Roll-Off)

01234

Frequency (x fS)

Amplitude (dB)

0.05

0.04

0.03

0.02

0.01

–0.01

–0.02

–0.03

–0.04

–0.05

FREQUENCY RESPONSE PASSBAND

(Sharp Roll-Off)

0 0.1 0.2 0.3 0.4 0.5

Frequency (x f

)

Amplitude (dB)

–20

–40

–60

–80

–100

–120

–140

FREQUENCY RESPONSE (Slow Roll-Off)

01234

Frequency (x fS)

Amplitude (dB)

De-Emphasis

0.0

–1.0

–2.0

–3.0

–4.0

–5.0

–6.0

–7.0

–8.0

–9.0

–10.0

DE-EMPHASIS (f

= 32kHz)

02468101214

Frequency (kHz)

Level (dB)

0.5

0.4

0.3

0.2

0.1

0.0

–0.1

–0.2

–0.3

–0.4

–0.5

DE-EMPHASIS ERROR (f

= 32kHz)

02468101214

Frequency (kHz)

Error (dB)

PCM1741

6SBAS175

TYPICAL PERFORMANCE CURVES (Cont.)

All specifications at TA = +25°C, VCC = VDD = 3.3V, system clock = 384fS (fS = 44.1kHz), and 24-bit input data, unless otherwise noted.

De-Emphasis (Cont.)

0.0

–1.0

–2.0

–3.0

–4.0

–5.0

–6.0

–7.0

–8.0

–9.0

–10.0

DE-EMPHASIS (f

= 44.1kHz)

0246810121416

18 20

Frequency (kHz)

Level (dB)

0.5

0.4

0.3

0.2

0.1

0.0

–0.1

–0.2

–0.3

–0.4

–0.5

DE-EMPHASIS ERROR (f

= 44.1kHz)

0246810121416

18 20

Frequency (kHz)

Error (dB)

0.0

–1.0

–2.0

–3.0

–4.0

–5.0

–6.0

–7.0

–8.0

–9.0

–10.0

DE-EMPHASIS (f

= 48kHz)

0246810121416

18 22

Frequency (kHz)

Level (dB)

0.5

0.4

0.3

0.2

0.1

0.0

–0.1

–0.2

–0.3

–0.4

–0.5

DE-EMPHASIS ERROR (f

= 48kHz)

0246810121416

18 22

Frequency (kHz)

Error (dB)

ANALOG DYNAMIC PERFORMANCE

All specifications at TA = +25°C, VCC = 5.0V, VDD = 3.3V, and 24-bit input data, unless otherwise noted.

Supply-Voltage Characteristics

0.1

0.01

0.001

THD+N vs V

2.4 2.7 3 3.63.3 3.9

(V)

THD+N (%)

–60dB/96kHz, 384f

–60dB/44.1kHz, 384f

0dB/96kHz, 384f

0dB/44.1kHz, 384f

106

104

102

100

DYNAMIC RANGE vs V

2.4 2.7 3 3.3 3.6 3.9

(V)

Dynamic Range (dB)

44.1kHz, 384f

96kHz, 384f

PCM1741 7

SBAS175

TYPICAL PERFORMANCE CURVES (Cont.)

All specifications at TA = +25°C, VCC = VDD = 3.3V, and 24-bit input data, unless otherwise noted.

Supply-Voltage Characteristics (Cont.)

106

104

102

100

SNR vs V

2.4 2.7 3 3.3 3.6 3.9 4.2

(V)

SNR (dB)

44.1kHz, 384f

96kHz, 384f

106

104

102

100

CHANNEL SEPARATION vs VCC

2.4 2.7 3 3.3 3.6 3.9

VCC (V)

Channel Separation (dB)

44.1kHz, 384fS

96kHz, 384fS

Temperature Characteristics

0.1

0.01

0.001

THD+N vs TA

–50 –25 0 25 50 75 100

Temperature (°C)

THD+N (%)

–60dB/96kHz, 384fS

–60dB/44.1kHz, 384fS

0dB/96kHz, 384fS

0dB/44.1kHz, 384fS

106

104

102

100

DYNAMIC RANGE vs T

–50 –25 0 25 50 75 100

Temperature (°C)

Dynamic Range (dB)

44.1kHz, 384f

96kHz, 384f

106

104

102

100

SNR vs T

–50 –25 0 25 50 75 100

Temperature (°C)

SNR (dB)

44.1kHz, 384f

96kHz, 384f

106

104

102

100

CHANNEL SEPARATION vs TA

–50 –25 0 25 50 75 100

Temperature (°C)

Channel Separation (dB)

44.1kHz, 384fS

96kHz, 384fS

PCM1741

8SBAS175

SYSTEM CLOCK AND RESET

FUNCTIONS

SYSTEM CLOCK INPUT

The PCM1741 requires a system clock for operating the

digital interpolation filters and multilevel delta-sigma modu-

lators. The system clock is applied at the SCK input (pin 16).

Table I shows examples of system clock frequencies for

common audio sampling rates.

Figure 1 shows the timing requirements for the system clock

input. For optimal performance, it is important to use a clock

source with low phase jitter and noise. The PLL1700 multi-

clock generator from Texas Instruments is an excellent choice

for providing the PCM1741 system clock.

POWER-ON RESET FUNCTIONS

The PCM1741 includes a power-on reset function, as shown in

Figure 2. With the system clock active, and VDD > 2.0V (typical

1.6V to 2.4V), the power-on reset function will be enabled. The

initialization sequence requires 1024 system clocks from the

time VDD > 2.0V. After the initialization period, the PCM1741

will be set to its reset default state, as described in the Mode

Control Register section of this data sheet.

During the reset period (1024 system clocks), the analog

outputs are forced to the bipolar zero level, or VCC/2. After

the reset period, the internal register is initialized in the next

1/fS period and, if SCK, BCK, and LRCK are provided

continuously, the PCM1741 provides proper analog output

with unit group delay against the input data.

FIGURE 1. System Clock Input Timing.

SAMPLING

FREQUENCY 256f

384f

512f

768f

8kHz 2.0480 3.0720 4.0960 6.1440

16kHz 4.0960 6.1440 8.1920 12.2880

32kHz 8.1920 12.2880 16.3840 24.5760

44.1kHz 11.2896 16.9344 22.5792 33.8688

48kHz 12.2880 18.4320 24.5760 36.8640

88.2kHz 22.5792 33.8688 45.1584 See Note (1)

96kHz 24.5760 36.8640 49.1520 See Note (1)

NOTE: (1) The 768fS system clock rate is not supported for fS > 64kHz.

TABLE I. System Clock Rates for Common Audio Sampling Frequencies.

SYSTEM CLOCK FREQUENCY (fSCLK) (MHz)

FIGURE 2. Power-On Reset Timing.

1024 System Clocks

Reset Reset Removal

VDD

Internal Reset

2.4V

2.0V

1.6V

System Clock

Don't Care

SCKH

SCKL

2.0V

0.8V

System Clock

System clock pulse

cycle time

(1)

“H”

“L”

System Clock Pulse Width HIGH t

SCKH

: 7ns (min)

System Clock Pulse Width LOW t

SCKL

: 7ns (min)

NOTE: (1) 1/256f

, 1/384f

, 1/512f

, and 1/768f

PCM1741 9

SBAS175

FIGURE 3. Audio Data Input Formats.

AUDIO SERIAL INTERFACE

The audio serial interface for the PCM1741 is comprised of

a 3-wire synchronous serial port. It includes LRCK (pin 3),

BCK (pin 1), and DATA (pin 2). BCK is the serial audio bit

clock, and is used to clock the serial data present on DATA

into the audio interface’s serial shift register. Serial data is

clocked into the PCM1741 on the rising edge of BCK.

LRCK is the serial audio left/right word clock used to latch

serial data into the serial audio interface’s internal registers.

Both LRCK and BCK should be synchronous to the

system clock. Ideally, it is recommended that LRCK and

BCK be derived from the system clock input, SCK. LRCK

is operated at the sampling frequency, fS. BCK may be

operated at 32, 48, or 64 times the sampling frequency (I2S

format except BCK = 32fS). Internal operation of the

PCM1741 is synchronized with LRCK. Accordingly, it is

held when the sampling rate clock of LRCK is changed or

SCK and/or BCK is broken at least for one clock cycle. If

SCK, BCK, and LRCK are provided continuously after this

hold condition, the internal operation will be resynchronized

automatically, less than 3/fS period. In this resynchronize

period, and following 3/fS, analog output is forced to the

bipolar zero level, or

/2.

External resetting is not required.

AUDIO DATA FORMATS AND TIMING

The PCM1741 supports industry-standard audio data formats,

including Standard, I2S, and Left-Justified, as shown in

Figure 3. Data formats are selected using the format bits,

FMT[2:0], in Control Register 20. The default data format is

24-bit left justified. All formats require Binary Two’s Comple-

ment, MSB-first audio data. See Figure 4 for a detailed timing

diagram of the serial audio interface.

1/f

L-Channel R-Channel

LRCK

BCK

(= 48 or 64f

)

18-Bit Right-Justified

DATA

(2) I

S Data Format: L-Channel = LOW, R-Channel = HIGH

(3) Left-Justified Data Format: L-Channel = HIGH, R-Channel = LOW

(1) Standard Data Format: L-Channel = HIGH, R-Channel = LOW

1/f

L-Channel R-Channel

LRCK

BCK

(= 32, 48

or 64f

)

1 2 3 N-2 N-1 N 1 2 1 23 N-2 N-1 N

1/f

L-Channel

R-Channel

LRCK

BCK

(= 32, 48 or 64f

)

1 2 3 N-2 N-1 N 1 2 3 N-2 N-1 N

14 15 16

16 17 18

18 19 20

14 15 16

123

DATA

22 23 24 22 23 24123

DATA

18 19 201 23

DATA

16 17 181 23

DATA

24-Bit Right-Justified

14 15 16123

22 23 24123

18 19 201 23

17 181 2

20-Bit Right-Justified

LSBMSB LSBMSB

LSBMSB

LSBMSBLSBMSB

LSBMSB LSBMSB

LSBMSB

14 15 16 14 15 16123

DATA

16-Bit Right-Justified, BCK = 32f

14 15 16123

LSBMSB LSBMSB

16-Bit Right-Justified, BCK = 48f

or 64f

PCM1741

10 SBAS175

FIGURE 5. Control Data Word Format for MDI.

FIGURE 6. Register Write Operation.

SERIAL CONTROL INTERFACE

The serial control interface is a 3-wire serial port that

operates asynchronously to the serial audio interface. The

serial control interface is utilized to program the on-chip

mode registers. The control interface includes MD (pin 13),

MC (pin 14), and ML (pin 15). MD is the serial data input,

used to program the mode registers, MC is the serial bit

clock, used to shift data into the control port, and ML is the

control port latch clock.

All write operations for the serial control port use 16-bit data

words. Figure 5 shows the control data word format. The

most significant bit must be a “0”. There are seven bits,

labeled IDX[6:0], that set the register index (or address) for

the write operation. The least significant eight bits, D[7:0],

contain the data to be written to the register specified by

IDX[6:0].

Figure 6 shows the functional timing diagram for writing the

serial control port. ML is held at a logic “1 ” state until a

ML is set to logic “0”. Sixteen clocks are then provided on

MC, corresponding to the 16 bits of the control data word on

MD. After the sixteenth clock cycle has completed, ML is set

to logic “1” to latch the data into the indexed mode control

CONTROL INTERFACE TIMING REQUIREMENTS

See Figure 7 for a detailed timing diagram of the serial

control interface. These timing parameters are critical for

proper control port operation.

FIGURE 4. Audio Interface Timing.

SYMBOL PARAMETER MIN MAX UNITS

tBCY BCK Pulse Cycle Time

32, 48, or 64f

S(1)

tBCH BCK High Level Time 35 ns

tBCL BCK Low Level Time 35 ns

tBL BCK Rising Edge to LRCK Edge 10 ns

tLB LRCK Falling Edge to BCK Rising Edge 10 ns

tDS DATA Set Up Time 10 ns

tDH DATA Hold Time 10 ns

NOTE: (1) fS is the sampling frequency (e.g., 44.1kHz, 48kHz, 96kHz, etc.)

LRCK

BCK

DATA

50% of VDD

tBCH tBCL tLB

tBL

tDS tDH

tBCY

IDX5IDX60 IDX4 IDX2IDX3 IDX1 IDX0 D7 D6 D5 D4 D3 D2 D1 D0

MSB

LSB

0 D7D6D5D4D3D2 0

IDX6

D1 D0X XX

IDX6 IDX5 IDX4 IDX3 IDX2 IDX1 IDX0

PCM1741 11

SBAS175

MODE CONTROL REGISTERS

User-Programmable Mode Controls

The PCM1741 includes a number of user-programmable

functions that are accessed via control registers. The regis-

ters are programmed using the Serial Control Interface that

was previously discussed in the “Serial Control Interface”

section of this data sheet. Table II lists the available mode

control functions, along with their reset default conditions

and associated register index.

The mode control register map is shown in Table III. Each

IDX[6:0] bits.

FUNCTION RESET DEFAULT CONTROL REGISTER INDEX, IDX[6:0]

Digital Attenuation Control, 0dB to –63dB in 0.5dB Steps 0dB, No Attenuation 16 and 17 AT1[7:0], AT2[7:0]

Soft Mute Control Mute Disabled 18 MUT[2:0]

Oversampling Rate Control (64 or 128fS) 64fS Oversampling 18 OVER

DAC Operation Control DAC1 and DAC2 Enabled 19 DAC[2:1]

De-Emphasis Function Control De-Emphasis Disabled 19 DM12

De-Emphasis Sample Rate Selection 44.1kHz 19 DMF[1:0]

Audio Data Format Control 24-Bit Left Justified 20 FMT[2:0]

Digital Filter Roll-Off Control Sharp Roll-Off 20 FLT

Zero Flag Function Select L-/R-Channel Independent 22 AZRO

Output Phase Select Normal Phase 22 DREV

Zero Flag Polarity Select High 22 ZREV

TABLE II. User-Programmable Mode Controls.

TABLE III. Mode Control Register Map.

IDX

(B8-B14) REGISTER B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0

10H16 0 IDX6 IDX5 IDX4 IDX3 IDX2 IDX1 IDX0 AT17 AT16 AT15 AT14 AT13 AT12 AT11 AT10

11H17 0 IDX6 IDX5 IDX4 IDX3 IDX2 IDX1 IDX0 AT27 AT26 AT25 AT24 AT23 AT22 AT21 AT20

12H18 0 IDX6 IDX5 IDX4 IDX3 IDX2 IDX1 IDX0 RSV(1) OVER RSV(1) RSV(1) RSV(1) RSV(1) MUT2 MUT1

13H19 0 IDX6 IDX5 IDX4 IDX3 IDX2 IDX1 IDX0 RSV(1) DMF1 DMF0 DM12 RSV(1) RSV(1) DAC2 DAC1

14H20 0 IDX6 IDX5 IDX4 IDX3 IDX2 IDX1 IDX0 RSV(1) RSV(1) FLT RSV(1) RSV(1) FMT2 FMT1 FMT0

15H21 0 IDX6 IDX5 IDX4 IDX3 IDX2 IDX1 IDX0 RSV(1) RSV(1) RSV(1) RSV(1) RSV(1) RSV(1) RSV(1) RSV(1)

16H22 0 IDX6 IDX5 IDX4 IDX3 IDX2 IDX1 IDX0 RSV(1) RSV(1) RSV(1) RSV(1) RSV(1) AZRO ZREV DREV

NOTE: (1) RSV = Reserved for test operation. It should be set to “0” when in regular operation.

SYMBOL PARAMETER MIN TYP MAX UNITS

tMCY MC Pulse Cycle Time 100 ns

tMCL MC Low Level Time 50 ns

tMCH MC High Level Time 50 ns

tMHH ML High Level Time Note (2) ns

tMLS ML Falling Edge to MC Rising Edge 20 ns

tMLH ML Hold Time(1) 20 ns

tMDH MD Hold Time 15 ns

tMDS MD Set Up Time 20 ns

NOTES: (1) MC rising edge for LSB to ML rising edge. (2)

256 •f

sec (min), fS = Sampling Rate.

FIGURE 7. Control Interface Timing.

50% of V

MLS

MCH

MCY

MDS

MCH

MCL

MHH

MLH

LSB

PCM1741

12 SBAS175

B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0

ATx[7:0] Digital Attenuation Level Setting

where x = 1 or 2, corresponding to the DAC output VOUTL (x = 1) and VOUTR (x = 2).

Default Value: 1111 1111B

Each DAC channel (VOUTL and VOUTR) includes a digital attenuator function. The attenuation level may be

set from 0dB to –63dB, in 0.5dB steps. Changes in attentuator levels are made by incrementing or

decrementing, by one step (0.5dB), for every 8/fS time interval until the programmed attenuator setting is

reached. Alternatively, the attenuator level may be set to infinite attenuation (or mute). The attenuation data

for each channel can be set individually.

The attenuation level may be set using the formula below.

Attenuation Level (dB) = 0.5 (ATx[7:0]DEC – 255)

where: ATx[7:0]DEC = 0 through 255

for: ATx[7:0]DEC = 0 through 128, the attenuator is set to infinite attenuation.

The following table shows attenuator levels for various settings.

ATx[7:0] Decimal Value Attenuator Level Setting

1111 1111B255 0dB, No Attenuation (default)

1111 1110B254 –0.5dB

1111 1101B253 –1.0dB

1000 0011B131 –62.0dB

1000 0010B130 –62.5dB

1000 0001B129 –63.0dB

1000 0000B128 Mute

•••

0000 0000B0 Mute

B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0

MUTx Soft Mute Control

Where x = 1 or 2, corresponding to the DAC output VOUTL (x = 1) and VOUTR (x = 2).

Default Value: 0

MUTx = 0 Mute Disabled (default)

MUTx = 1 Mute Enabled

The mute bits, MUT1 and MUT2, are used to enable or disable the Soft Mute function for the corresponding

DAC outputs, VOUTL and VOUTR. The Soft Mute function is incorporated into the digital attenuators. When

Mute is disabled (MUTx = 0), the attenuator and DAC operate normally. When Mute is enabled by setting

MUTx = 1, the digital attenuator for the corresponding output will be decreased from the current setting to

the infinite attenuation setting, one attenuator step (0.5dB) at a time. This provides a “pop”-free muting of the

DAC output. By setting MUTx = 0, the attenuator will be increased one step at a time to a previously

programmed attenuation level.

OVER Oversampling Rate Control

Default Value: 0

OVER = 0 64x Oversampling (default)

OVER = 1 128x Oversampling

The OVER bit is used to control the oversampling rate of the delta-sigma DACs.

PCM1741 13

SBAS175

B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0

DACx DAC Operation Control

where x = 1 or 2, corresponding to the DAC output VOUTL (x = 1) or VOUTR (x = 2).

Default Value: 0

DACx = 0 DAC Operation Enabled (default)

DACx = 1 DAC Operation Disabled

The DAC operation controls are used to enable and disable the DAC outputs, VOUTL and VOUTR. When

DACx = 0, the corresponding output will generate the audio waveform dictated by the data present on the

DATA pin. When DACx = 1, the corresponding output will be set to the bipolar zero level, or

/2.

DM12 Digital De-Emphasis Function Control

Default Value: 0

DM12 = 0 De-Emphasis Disabled (default)

DM12 = 1 De-Emphasis Enabled

The DM12 bit is used to enable or disable the Digital De-Emphasis function. Refer to the Typical Performance

Curves of this data sheet for more information.

DMF[1:0] Sampling Frequency Selection for the De-Emphasis Function

Default Value: 00

DMF[1:0] De-Emphasis Same Rate Selection

00 44.1kHz (default)

01 48kHz

10 32kHz

11 Reserved

The DMF[1:0] bits are used to select the sampling frequency used for the Digital De-Emphasis function when

it is enabled.

B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0

FMT[2:0] Audio Interface Data Format

Default Value: 101

The FMT[2:0] bits are used to select the data format for the serial audio interface. The following table shows

the available format options.

FMT[2:0] Audio Data Format Selection

000 24-Bit Standard Format, Right-Justified Data

001 20-Bit Standard Format, Right-Justified Data

010 18-Bit Standard Format, Right-Justified Data

011 16-Bit Standard Format, Right-Justified Data

100 I2S Format, 16- to 24-bits

101 Left-Justified Format, 16- to 24-Bits (default)

110 Reserved

111 Reserved

PCM1741

14 SBAS175

FLT Digital Filter Roll-Off Control

Default Value: 0

FLT = 0 Sharp Roll-Off (default)

FLT = 1 Slow Roll-Off

The FLT bit allows the user to select the digital filter roll-off that is best suited to their application. Two

filter roll-off sections are available: Sharp or Slow. The filter responses for these selections are shown in

the Typical Performance Curves section of this data sheet.

B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0

DREV Output Phase Select

Default Value: 0

DREV = 0 Normal Output (default)

DREV = 1 Inverted Output

The DREV bit is used to set the output phase of VOUTL and VOUTR.

ZREV Zero Flag Polarity Select

Default Value: 0

ZREV = 0 Zero Flag Pins HIGH at a Zero Detect (default)

ZREV = 1 Zero Flag Pins LOW at a Zero Detect

The ZREV bit allows the user to select the active polarity of Zero Flag pins.

AZRO Zero Flag Function Select

Default Value: 0

AZRO = 0 L-/R-Channel Independent Zero Flag (default)

AZRO = 1 L-/R-Channel Common Zero Flag

Register22 (Cont.)

The AZRO bit allows the user to select the function of Zero Flag pins.

AZRO = 0:

Pin11: ZEROR; Zero Flag Output for R-Channel

Pin12: ZEROL; Zero Flag Output for L-Channel

AZRO = 1:

Pin11: ZEROA; Zero Flag Output for L-/R-Channel

Pin12: NA; No Assign

PCM1741 15

SBAS175

ANALOG OUTPUTS

The PCM1741 includes two independent output channels:

VOUTL and VOUTR. These are unbalanced outputs, each capable

of driving 2.05Vp-p typical into a 5kΩ AC-coupled load. The

internal output amplifiers for VOUTL and VOUTR are biased to the

DC common-mode (or bipolar zero) voltage, equal to VCC/2.

The output amplifiers include an RC continuous-time filter that

helps to reduce the out-of-band noise energy present at the

DAC outputs, due to the noise shaping characteristics of the

PCM1741’s delta-sigma DACs. The frequency response of this

filter is shown in Figure 8. By itself, this filter is not enough to

attenuate the out-of-band noise to an acceptable level for many

applications, therefore, an external low-pass filter is required to

provide sufficient out-of-band noise rejection. Further discus-

sion of DAC post-filter circuits is provided in the Applications

Information section of this data sheet.

VCOM OUTPUT

One unbuffered common-mode voltage output pin, VCOM

(pin 10), is brought out for decoupling purposes. This pin is

FIGURE 8. Output Filter Frequency Response.

0.1 1 10 100 1K 10K

–10

–20

–30

–40

–50

–60

Response (dB)

Frequency (kHz)

ANALOG FILTER PERFORMANCE

(100Hz-10MHz)

nominally biased to a DC voltage level equal to

/2.

This

pin may be used to bias external circuits. Figure 9 shows an

example of using the VCOM pin for external biasing applica-

tions.

FIGURE 9. Biasing External Circuits Using the VCOM Pin.

10µF

(a) Using V

COM

to Bias a Single-Supply Filter Stage

(b) Using a Voltage Follower to Buffer V

COM

when Biasing Multiple Nodes

x = L or R 10µF

Filtered

Output

OPA342

= –1, where A

= –

OUT

COM

PCM1741

Buffered

COM

1/2

OPA2342

10µF

PCM1741

16 SBAS175

ZERO FLAGS

Zero Detect Condition

Zero Detection for each output channel is independent from

the other. If the data for a given channel remains at a “0”

level for 1024 sample periods (or LRCK clock periods), a

Zero Detect condition exists for that channel.

Zero Output Flags

Given that a Zero Detect condition exists for one or more

channels, the Zero Flag pins for those channels will be set to

a logic “1” state. There are Zero Flag pins for each channel:

ZEROL (pin 12) and ZEROR (pin 11). These pins can be used

to operate external mute circuits, or used as status indicators

for a microcontroller, audio signal processor, or other digitally

controlled functions.

The active polarity of Zero Flag output can be inverted by

setting the ZREV bit of Control Register 22 to “1”. The reset

default is active high output, or ZREV = 0.

The L-channel and R-channel common Zero Flag can be

selected by setting the AZRO bit of Control Register 22 to “1”.

The reset default is L-channel and R-channel independent

Zero Flag, or AZRO = 0.

APPLICATIONS INFORMATION

CONNECTION DIAGRAMS

A basic connection diagram is shown in Figure 11, with the

necessary power-supply bypassing and decoupling compo-

nents. Texas Instruments recommends using the component

values shown in Figure 11 for all designs.

The use of series resistors (22Ω to 100Ω) are recommended

for the SCK, LRCK, BCK, and DATA inputs. The series

resistor combines with stray PCB and device input capaci-

tance to form a low-pass filter that reduces high-frequency

noise emissions and helps to dampen glitches and ringing

present on clock and data lines.

FIGURE 11. Basic Connection Diagram.

BCK

DATA

LRCK

DGND

VDD

VCC

VOUTL

VOUTR

SCK

ZEROL/NA

ZEROR/ZEROA

VCOM

AGND

Post LPF

+3.3V

Regulator

Mode

Control

Zero Mute

Control

System Clock

PCM

Audio Data

Input

+3.3V

L-Chan OUT

10µF

Post LPF

R-Chan OUT

POWER SUPPLIES AND GROUNDING

The PCM1741 requires a +3.3V analog supply (V

) and a

+3.3V digital supply (V

). The +3.3V supply (V

) is used to

power the DAC analog and output filter circuitry, while the

+3.3V (V

) supply is used to power the digital filter and serial

interface circuitry. For best performance, the +3.3V (V

)

supply should be derived from the +3.3V (V

) supply using a

linear regulator, as shown in Figure 11.

Proper power-supply bypassing is shown in Figure 10. The

10µF capacitors should be tantalum or aluminum electrolytic,

while the 0.1µF capacitors are ceramic (X7R type is recom-

mended for surface-mount applications).

FIGURE 10. Dual-Supply Filter Circuit.

OUT

OPA2134

≈ –

DAC OUTPUT FILTER CIRCUITS

Delta-sigma DACs utilize noise-shaping techniques to im-

prove in-band Signal-to-Noise Ratio (SNR) performance at

the expense of generating increased out-of-band noise above

the Nyquist Frequency, or fS/2. The out-of-band noise must

be low-pass filtered in order to provide the optimal converter

performance. This is accomplished by a combination of

on-chip and external low-pass filtering.

Figures 9(a) and 10 show the recommended external low-

pass active filter circuits for single- and dual-supply applica-

tions. These circuits are second-order Butterworth filters

PCM1741 17

SBAS175

using a Multiple FeedBack (MFB) circuit arrangement that

reduces sensitivity to passive component variations over

frequency and temperature. For more information regarding

MFB active filter design, please refer to Burr-Brown Appli-

cations Bulletin #34 AB-034 (SBFA001), available from our

web site at http://www.ti.com.

Since the overall system performance is defined by the

quality of the DACs and their associated analog output

circuitry, high-quality audio op amps are recommended for

the active filters. The OPA2353 and OPA2134 dual op amps

from Texas Instruments are recommended for use with the

PCM1741, see Figures 9(a) and 10.

PCB LAYOUT GUIDELINES

A typical PCB floor plan for the PCM1741 is shown in

Figure 12. A ground plane is recommended, with the analog

and digital sections being isolated from one another using a

split or cut in the circuit board. The PCM1741 should be

oriented with the digital I/O pins facing the ground plane

split/cut to allow for short, direct connections to the digital

audio interface and control signals originating from the

digital section of the board.

PCM1741

VCC

VDD

DGND

Return Path for Digital Signals

Analog

Ground

Digital

Ground

AGND

Output

Circuits

DIGITAL SECTION ANALOG SECTION

Digital Logic

and

Audio

Processor

Digital Power

+VDDGND

Analog Power

+3.3V +VS

AGND

REG

–VS

FIGURE 12. Recommended PCB Layout.

PCM1741

18 SBAS175

FIGURE 14. 8-Level Delta-Sigma Modulator.

–1

8-Level Quantizer

–1

–

–1

64f

PCM1741

DGND Output

Circuits

RF Choke or Ferrite Bead

Common

Ground

AGND

DIGITAL SECTION ANALOG SECTION

Power Supplies

+3.3V +V

AGND

REG

–V

FIGURE 13. Single-Supply PCB Layout.

Separate power supplies are recommended for the digital

and analog sections of the board. This prevents the switching

noise present on the digital supply from contaminating the

analog power supply and degrading the dynamic perfor-

mance of the PCM1741. In cases where a common +3.3V

supply must be used for the analog and digital sections, an

inductance (RF choke, ferrite bead) should be placed be-

tween the analog and digital +3.3V supply connections to

avoid coupling of the digital switching noise into the analog

circuitry. Figure 13 shows the recommended approach for

single-supply applications.

THEORY OF OPERATION

The delta-sigma section of the PCM1741 is based on an

8-level amplitude quantizer and a fourth-order noise shaper. This

section converts the oversampled input data to 8-level delta-sigma

format. A block diagram of the 8-level delta-sigma modulator is

shown in Figure 14. This 8-level delta-sigma modulator has the

advantage of stability and clock jitter sensitivity over the typical

one-bit (2-level) delta-sigma modulator. The combined

oversampling rate of the delta-sigma modulator and the interpo-

lation filter is 64fS.

PCM1741 19

SBAS175

The theoretical quantization noise performance of the

8-level delta-sigma modulator is shown in Figure 15. The en-

hanced multilevel delta-sigma architecture also has advantages

for input clock jitter sensitivity due to the multilevel quantizer,

with the simulated jitter sensitivity, as shown in Figure 16.

KEY PERFORMANCE PARAMETERS

AND MEASUREMENT

This section provides information on how to measure key

dynamic performance parameters for the PCM1741. In all

cases, an Audio Precision System Two Cascade or equivalent

audio measurement system is utilized to perform the testing.

TOTAL HARMONIC DISTORTION + NOISE

Total Harmonic Distortion + Noise (THD+N) is a significant

figure of merit for audio DACs, since it takes into account

both harmonic distortion and all noise sources within a

specified measurement bandwidth. The true rms value of the

distortion and noise is referred to as THD+N. Figure 17

shows the test setup for THD+N measurements.

For the PCM1741, THD+N is measured with a full-scale,

1kHz digital sine wave as the test stimulus at the input of the

DAC. The digital generator is set to a 24-bit audio word

length and a sampling frequency of 44.1kHz or 96kHz. The

digital generator output is taken from the unbalanced

S/PDIF connector of the measurement system. The S/PDIF

FIGURE 16. Jitter Sensitivity.

0 100 200 300 400 500 600

125

120

115

110

105

100

Dynamic Range (dB)

Jitter (ps)

JITTER DEPENDENCE (64x Oversampling)

FIGURE 17. Test Setup for THD+N Measurements.

S/PDIF

Receiver

Evaluation Board

f–3dB = 54kHz or 108kHz

PCM1741

DEM-DAI1741

2nd-Order

Low-Pass

Filter

Notch FilterBand Limit

HPF = 22Hz

LPF = 30kHz fC = 1kHzrms Mode0dBFS,

1kHz Sine Wave

S/PDIF

Output

Analyzer

and

Display

20kHz

Apogee

Filter

Digital

Generator

FIGURE 15. Quantization Noise Spectrum.

012345678

–20

–40

–60

–80

–100

–120

–140

–160

–180

Amplitude (dB)

Frequency (fS)

QUANTIZATION NOISE SPECTRUM

(64x Oversampling) QUANTIZATION NOISE SPECTRUM

(128x Oversampling)

012345678

–20

–40

–60

–80

–100

–120

–140

–160

–180

Amplitude (dB)

Frequency (fS)

PCM1741

20 SBAS175

FIGURE 18. Test Setup for Dynamic Range and SNR Measurements.

S/PDIF

Receiver

Evaluation Board

PCM1741(1)

DEM-DAI1741

2nd-Order

Low-Pass

Filter

Notch FilterBand Limit

HPF = 22Hz

LPF = 22kHz fC = 1kHz

f–3dB = 54kHz

0% Full-Scale,

Dither Off (SNR)

–60dBFS,

1kHz Sine Wave

(Dynamic Range)

S/PDIF

Output

Option = A-Weighting(2)

A-Weight

Filter(1)

rms Mode

Analyzer

and

Display

Digital

Generator

NOTES: (1) Infinite Zero Detect Mute disabled.

(2) Results without A-Weighting will be approxi-

mately 3dB worse.

data is transmitted via a coaxial cable to the digital audio

receiver on the DEM-DAI1741 demo board. The receiver is

then configured to output 24-bit data in either I2S or left-

justified data format. The DAC audio interface format is

programmed to match the receiver output format. The ana-

log output is then taken from the DAC post filter and

connected to the analog analyzer input of the measurement

system. The analog input is band limited using filters resi-

dent in the analyzer. The resulting THD+N is measured by

the analyzer and displayed by the measurement system.

DYNAMIC RANGE

Dynamic range is specified as A-Weighted, THD+N mea-

sured with a –60dBFS, 1kHz digital sine wave stimulus at

the input of the DAC. This measurement is designed to give

a good indicator of how the DAC will perform given a low-

level input signal.

The measurement setup for the dynamic range measurement

is shown in Figure 18, and is similar to the THD+N test

setup discussed previously. The differences include the band

limit filter selection, the additional A-Weighting filter, and

the –60dBFS input level.

IDLE CHANNEL SIGNAL-TO-NOISE RATIO

The SNR test provides a measure of the noise floor of the

DAC. The input to the DAC is all “0”s data, and the DAC’s

Infinite Zero Detect Mute function must be disabled (default

condition at power up for the PCM1741). This ensures that

the delta-sigma modulator output is connected to the output

amplifier circuit so that idle tones (if present) can be ob-

served and effect the SNR measurement. The dither function

of the digital generator must also be disabled to ensure an all

“0”s data stream at the input of the DAC. The measurement

setup for SNR is identical to that used for dynamic range,

with the exception of the input signal level (see the notes

provided in Figure 18).

PACKAGING INFORMATION

Orderable Device Status (1) Package

Type Package

Drawing Pins Package

Qty Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)

PCM1741E ACTIVE SSOP/

QSOP DBQ 16 75 Green (RoHS &

no Sb/Br) CU NIPDAU Level-1-260C-UNLIM

PCM1741E/2K ACTIVE SSOP/

QSOP DBQ 16 2000 Green (RoHS &

no Sb/Br) CU NIPDAU Level-1-260C-UNLIM

PCM1741E/2KG4 ACTIVE SSOP/

QSOP DBQ 16 2000 Green (RoHS &

no Sb/Br) CU NIPDAU Level-1-260C-UNLIM

PCM1741EG4 ACTIVE SSOP/

QSOP DBQ 16 75 Green (RoHS &

no Sb/Br) CU NIPDAU Level-1-260C-UNLIM

(1) The marketing status values are defined as follows:

ACTIVE: Product device recommended for new designs.

LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.

NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in

a new design.

PREVIEW: Device has been announced but is not in production. Samples may or may not be available.

OBSOLETE: TI has discontinued the production of the device.

(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check

http://www.ti.com/productcontent for the latest availability information and additional product content details.

TBD: The Pb-Free/Green conversion plan has not been defined.

Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements

for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered

at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.

Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and

package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS

compatible) as defined above.

Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame

retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)

(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder

temperature.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is

provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the

accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take

reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on

incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited

information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI

to Customer on an annual basis.

PACKAGE OPTION ADDENDUM

www.ti.com 23-Jul-2008

Addendum-Page 1

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device Package

Type Package

Drawing Pins SPQ Reel

Diameter

(mm)

Reel

Width

W1 (mm)

A0 (mm) B0 (mm) K0 (mm) P1

(mm) W

(mm) Pin1

Quadrant

PCM1741E/2K SSOP/

QSOP DBQ 16 2000 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1

PACKAGE MATERIALS INFORMATION

www.ti.com 11-Mar-2008

Pack Materials-Page 1

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)

PCM1741E/2K SSOP/QSOP DBQ 16 2000 346.0 346.0 29.0

PACKAGE MATERIALS INFORMATION

www.ti.com 11-Mar-2008

Pack Materials-Page 2

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,and other changes to its products and services at any time and to discontinue any product or service without notice. Customers shouldobtain the latest relevant information before placing orders and should verify that such information is current and complete. All products aresold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standardwarranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except wheremandated by government requirements, testing of all parameters of each product is not necessarily performed.TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products andapplications using TI components. To minimize the risks associated with customer products and applications, customers should provideadequate design and operating safeguards.TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Informationpublished by TI regarding third-party products or services does not constitute a license from TI to use such products or services or awarranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectualproperty of the third party, or a license from TI under the patents or other intellectual property of TI.Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompaniedby all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptivebusiness practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additionalrestrictions.

Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids allexpress and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is notresponsible or liable for any such statements.TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonablybe expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governingsuch use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, andacknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their productsand any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may beprovided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products insuch safety-critical applications.TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products arespecifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet militaryspecifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely atthe Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products aredesignated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designatedproducts in automotive applications, TI will not be responsible for any failure to meet such requirements.Following are URLs where you can obtain information on other Texas Instruments products and application solutions:Products ApplicationsAmplifiers amplifier.ti.com Audio www.ti.com/audioData Converters dataconverter.ti.com Automotive www.ti.com/automotiveDSP dsp.ti.com Broadband www.ti.com/broadbandClocks and Timers www.ti.com/clocks Digital Control www.ti.com/digitalcontrolInterface interface.ti.com Medical www.ti.com/medicalLogic logic.ti.com Military www.ti.com/militaryPower Mgmt power.ti.com Optical Networking www.ti.com/opticalnetworkMicrocontrollers microcontroller.ti.com Security www.ti.com/securityRFID www.ti-rfid.com Telephony www.ti.com/telephonyRF/IF and ZigBee® Solutions www.ti.com/lprf Video & Imaging www.ti.com/videoWireless www.ti.com/wireless