115 MHz SAW Filter
6 MHz Bandwidth
Part Number: SF0115BA03088S
Spectrum Microwave
400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401
www.SpectrumMicrowave.com
DSSF0115BA03088S Rev A 22-Feb-2010
ECN 36650 Page 1 of 4
DESCRIPTION
• 115 MHz SAW bandpass filter with 6 MHz bandwidth for CDMA2000 applications.
• 19 x 6.5 mm SMP.
• RoHS compliant.
TYPICAL PERFORMANCE
Horizontal: Frequency : 3 MHz/div
Vertical from top: Relative Magnitude : 10 dB/div
Relative magnitude : 1 dB/div
Group Delay : 150 ns/div
S11 (112.2 to 117.8 MHz) S22 (112.2 to 117.8 MHz)
Circle: 1.8:1 VSWR limit Circle: 1.8:1 VSWR limit
115 MHz SAW Filter
6 MHz Bandwidth
Part Number: SF0115BA03088S
Spectrum Microwave
400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401
www.SpectrumMicrowave.com
DSSF0115BA03088S Rev A 22-Feb-2010
ECN 36650 Page 2 of 4
SPECIFICATION
Parameter Min Typ Max Units
All electrical specifications apply over the full -10ºC to +50ºC operating range and
include allowance for all manufacturing tolerances
Center Frequency FC 1
114.88 115 115.12 MHz
1 dB Bandwidth 2 5.6 6.08 MHz
3 dB Bandwidth 2 6.0 6.44 MHz
40 dB Bandwidth 2 7.75 8.2 MHz
Stopband Rejection, 25 MHz to 100 MHz 45 58 dB
Stopband Rejection, 130 MHz to 1000 MHz 45 53 dB
Minimum Insertion Loss 18.9 20 dB
Passband Amplitude Variation, FC ± 2.8 MHz 3 0.6 0.8 dB p-p
Passband Group Delay Variation, FC ± 2.8 MHz 100 150 ns p-p
Absolute Delay 2.0 2.1 µs
Input VSWR, FC ± 2.8 MHz 4 1.55 1.8 : 1
Output VSWR, FC ± 2.8 MHz 4 1.3 1.8 : 1
Maximum Input Level 20 dBm
Source and Load Impedance 50 Ω
Notes: 1. Defined as the mean of the 10dB frequencies.
2. dB levels are taken to be relative to the insertion loss.
3. Excludes final roll-offs to the 1dB points. Note that ‘Passband Amplitude
Variation’ includes Ripple (fast variations) and Slope (slow variations).
4. When matched using circuit below.
MAXIMUM RATINGS
Parameter Min Max Units
Storage Temperature Range -45 85 ˚C
Operating Temperature Range -10 50 ˚C
Operating Input Power Level - +20 dBm
D.C. Voltage between each pad - 15 VDC
MATCHING CIRCUIT
Typical component values:
Notes:
1. Recommended tolerances: +/-2% inductors, minimum Q=40, +/-5% resistors and capacitors.
2. Component values are for reference only and may change depending on board layout.
Rp1 = 430 Ω Rp2 = 200 Ω
Ls1 = 68 nH Ls2 = 68 nH
Cp1 = 56 pF Cp2 = 56 pF
Input
50 Ω
Single-ended
Output
50 Ω
Single-ended
10 5
1,2,3,4,6,7,8,9
115 MHz SAW Filter
6 MHz Bandwidth
Part Number: SF0115BA03088S
Spectrum Microwave
400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401
www.SpectrumMicrowave.com
DSSF0115BA03088S Rev A 22-Feb-2010
ECN 36650 Page 3 of 4
PACKAGE OUTLINE SUGGESTED FOOTPRINT
Units: mm
Tolerances are ±0.15 mm except
for the overall length, width and
pad dimensions, which are nominal
values.
Pad Configuration:
Input: 10
Output: 5
Ground: all other pads
Package Material:
Body: Al2O3 ceramic
Lid: Kovar, Ni plated
Terminations: Au plating 1 µm min,
over a 1.3-8.9 µm Ni plating
115 MHz SAW Filter
6 MHz Bandwidth
Part Number: SF0115BA03088S
Spectrum Microwave
400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401
www.SpectrumMicrowave.com
DSSF0115BA03088S Rev A 22-Feb-2010
ECN 36650 Page 4 of 4
PHYSICAL AND ENVIRONMENTAL CHARACTERISTICS
Parameter Qualification Conditions
Life Testing High temperature bake at +85 ºC for 168 hours.
Temperature Cycling
MIL-STD 883, Method 1010:
-40 ºC to +85 ºC, 10 cycles, 10 minutes dwell at
temperature extremes
Vibration
MIL-STD-202, Method 201A:
10 to 55 Hz, double amplitude of 0.06” for 2 hours in
each axis.
Mechanical Shock MIL-STD-883, Method 2002, Test Condition B:
1500 g, 3 impacts each axis
Solder Heat Resistance and Reflow
Condition
Peak temperature 240+/-5 ºC for 10 seconds.
Pre-heat: 150-170 ºC for 60 to 90 seconds.
Peak dwell: over 200 ºC for 23 to 26 seconds.
Handling: Class 1 per MIL-STD-1686
Reflow Profile is shown at the bottom of this table.
Lead Integrity MIL-STD 883 Method 2004, Condition D
8 oz for 30 seconds.
Solderability MIL-STD-883 Method 2003:
245 ºC +/-5 ºC; 95% coverage; no steam aging
Hermeticity MIL-STD 883 Method 1014:
Condition A2 and Condition C (no bomb)
ESD Classification Class I per MIL-STD-883 Method 3015
Precautions
Do not subject devices to ultrasonic cleaning, which
may cause deterioration and destruction of the
device.
Reflow Profile
0
50
100
150
200
250
0 50 100 150 200 250 300
TIME (sec)
TEMP (deg C)
All specifications are believed to be accurate and reliable. However, Spectrum Microwave reserves the right to make changes without notice.
© 2010 All rights reserved.
ISO 9001
Registered
