SILICON RFIC LOW CURRENT AMPLIFIER FOR MOBILE COMMUNICATIONS D FEATURES UPC8178TB POWER GAIN vs. FREQUENCY * LOW CURRENT CONSUMPTION ICC = 1.9 mA TYP @ VCC = 3.0 V +20 VCC = 3.0 V 2.4 GHz 1.0 GHz * SUPPLY VOLTAGE: VCC = 2.4 to 3.3 V TA = -40C TA = +25C UE +10 TA = +85C 0 -10 1.9 GHz -20 -30 IN -40 0.1 0.3 1.0 3.0 DESCRIPTION The UPC8178TB is a silicon monolithic integrated circuit designed as an amplifier for mobile communications. This IC can realize low current consumption with an external chip inductor which cannot be realized on an internal 50 wideband matched IC. This low current amplifier operates on 3.0 V. This device is manufactured using NEC's 30 GHz fmax UHS0 (Ultra High Speed Process) silicon bipolar process which uses direct silicon nitride passivation film and gold electrodes. These materials can protect the chip surface from pollution and prevent corrosion/migration. Thus, this IC has excellent performance, uniformity and reliability. NT * EXCELLENT ISOLATION: ISOL = 39 dB TYP @ f = 1.0 GHz ISOL = 40 dB TYP @ f = 1.9 GHz ISOL = 38 dB TYP @ f = 2.4 GHz * POWER GAIN: GP = 11.0 dB TYP @ f = 1.0 GHz GP = 11.5 dB TYP @ f = 1.9 GHz GP = 11.5 dB TYP @ f = 2.4 GHz * OPERATING FREQUENCY: 0.1 to 2.4 GHz (Output port LC matching) * 1 dB GAIN COMPRESSION OUTPUT POWER: PO(1 dB) = -4.0 dBm TYP @ f = 1.0 GHz PO(1 dB) = -7.0 dBm TYP @ f = 1.9 GHz PO(1 dB) = -7.5 dBm TYP @ f = 2.4 GHz * HIGH-DENSITY SURFACE MOUNTING: 6-pin super minimold package (2.0 x 1.25 x 0.9 mm) * LOW WEIGHT: 7 mg (Standard Value) APPLICATIONS SC O * Buffer Amplifiers on 0.1 to 2.4 GHz mobile communications system NEC's stringent quality assurance and test procedures ensure the highest reliability and performance. ELECTRICAL CHARACTERISTICS (TA = 25C, VCC = VOUT = 3.0 V, ZS = ZL = 50 , at LC matched frequency unless otherwise specified)) PART NUMBER PACKAGE OUTLINE PARAMETERS AND CONDITIONS1 SYMBOLS ICC UPC8178TB S06 Circuit Current (no signal) GP Power Gain ISOL DI Isolation f = 1.0 GHz f = 1.9 GHz f = 2.4 GHz f = 1.0 GHz f = 1.9 GHz f = 2.4 GHz PO(1dB) 1 dB Gain Compression Output Power NF Noise Figure RLin Input Return Loss f = 1.0 GHz f = 1.9 GHz f = 2.4 GHz f = 1.0 GHz f = 1.9 GHz f = 2.4 GHz f = 1.0 GHz f = 1.9 GHz f = 2.4 GHz UNITS MIN TYP MAX mA 1.4 1.9 2.4 dB dB dB dB dB dB dBm dBm dBm dB dB dB dB dB dB 9.0 9.0 9.0 34 35 33 -8.0 -11.0 -11.5 - - - 4 5 6.5 11.0 11.5 11.5 39 40 38 -4.0 -7.0 -7.5 5.5 5.5 5.5 7 8 9.5 13.0 13.5 13.5 - - - - - - 7.0 7.0 7.0 - - - California Eastern Laboratories UPC8178TB ABSOLUTE MAXIMUM RATINGS1 RECOMMENDED OPERATING CONDITIONS (TA = +25C unless otherwise specified) PARAMETERS UNITS RATINGS V 3.6 15 Voltage2 SYMBOLS VCC Supply ICC Circuit Current mA PD Power Dissipation3 mW 270 TA Operating Ambient Temperature C -40 to +85 Storage Temperature C -55 to +150 dBm +5 TSTG PIN Input Power VCC TA PARAMETERS UNITS MIN TYP MAX Supply Voltage1 V 2.4 3.0 3.3 Operating Ambient Temperature C -40 +25 +85 Note: 1. Same voltage applied to pins 4 and 6. D SYMBOLS IN UE Notes: 1. Operation in excess of any one of these conditions may result in permanent damage. 2. Pins 4 and 6. 3. Mounted on a double-sided copper clad 50x50x1.6 mm epoxy glass PWB, TA = +85C. SERIES PRODUCTS1 (TA = +25C, VCC = Vout = 3.0 V, ZS = ZL = 50 ) 1.0 GHz output port matching frequency GP ISOL PO(1 dB) (dB) (dB) (dBm) 11 39 -4.0 13.5 44 +3.0 Part No. UPC8178TB UPC8179TB ICC (mA) 1.9 4.0 UPC8128TB 2.8 12.5 UPC8151TB 4.2 12.5 UPC8152TB 5.6 23 1.9 GHz output port matching frequency GP ISOL PO(1 dB) (dB) (dB) (dBm) 11.5 40 -7.0 15.5 42 +1.5 39 -4.0 13 38 +2.5 40 -4.5 39 -4.0 15 36 19.5 38 2.4 GHz output port matching frequency GP ISOL PO(1 dB) (dB) (dB) (dBm) 11.5 38 -7.5 15.5 41 +1.0 13 37 -4.0 +1.5 15 34 +0.5 - -8.5 17.5 35 -8.5 - SC O Note: 1. Typical performance. 1.66 GHz output port matching frequency GP ISOL PO(1 dB) (dB) (dB) (dBm) - - - - - - NT Parameter - - Marking C3B C3C - C2P - - C2U - - C2V PIN FUNCTIONS (Pin Voltage is measured at VCC = 3.0 V) Pin No. Pin Name Applied Voltage (V) Pin Voltage (V) 1 Input -- 0.91 GND 0 -- DI 2 3 5 4 6 Output VCC Voltage same as VCC through external inductor 2.4 to 3.3 - Function and Applications Internal Equivalent Circuit Signal input pin. An internal matching circuit, configured with resistors, enables a 50 connection over a wide band. This pin must be coupled to the signal source with the capacitor for DC out. 6 Ground pin. This pin should be connected to the system ground with minimum inductance. Ground pattern on the board should be formed as wide as possible. All the ground pins must be connected together with a wide ground pattern to decrease impedance difference. 4 Signal output pin. This pin is designed as the collector output. Due to the high impedance output, this pin should be externally equipped with LC matching circuit to next stage. For L, a size 1005 chip inductor can be used. Power supply pin. This pin should be externally equipped with a bypass capacitor to minimize it's impedance. 2 3 1 5 UPC8178TB TEST CIRCUIT 1 (f = 1.0 GHz) VCC C3 D C4 Output port matching circuit L1 6 C1 4 1 C2 C3 50 OUT UE 50 IN 2, 3, 5 IN EXAMPLE OF TEST CIRCUIT 1 ASSEMBLED ON EVALUATION BOARD f = 1.0 GHz C3B L1 NT AMP. 4 Top View IN Connector Mounting direction C1 C5 SC O C4 COMPONENT LIST DI 1.0 GHz Output Port Matching C1, C3, C5 1000 pF C2 0.75 pF C4 10 pF L1 12 nH C2 C3 OUT Connector UPC8178TB TEST CIRCUIT 2 (f = 1.9 GHz) VCC C4 C5 D C6 Output port matching circuit L1 6 C1 C2 C3 50 OUT 4 1 UE 50 IN 2, 3, 5 IN EXAMPLE OF TEST CIRCUIT 2 ASSEMBLED ON EVALUATION BOARD f = 1.9 GHz C3B L1 NT AMP. 4 Top View IN Connector Mounting direction C1 C6 SC O C4 COMPONENT LIST 1.9 GHz Output Port Matching DI C1, C3, C5, C6 C2 1000 pF 0.5 pF C4 10 pF L1 3.9 nH C5 C2 C3 OUT Connector UPC8178TB TEST CIRCUIT 3 (f = 2.4 GHz) VCC C3 C4 D C5 Output port matching circuit L1 6 C1 50 OUT 4 1 UE 50 IN L2 C2 2, 3, 5 IN EXAMPLE OF TEST CIRCUIT 3 ASSEMBLED ON EVALUATION BOARD f = 2.4 GHz C3B L2 IN Connector C1 C5 Mounting direction C3 SC O C4 COMPONENT LIST 2.4 GHz Output Port Matching DI C1, C3, C4, C5 1000 pF C3 10 pF L1 1.8 nH L2 2.7 nH NOTES: 1. 42 x 35 x 0.4 mm double sided copper clad polyimide board. 2. Solder plated on pattern. 3. Back side: GND pattern. 4. Through holes. L1 NT AMP. 4 Top View C2 OUT Connector UPC8178TB OUTLINE DIMENSIONS (Units in mm) PIN CONNECTIONS PACKAGE OUTLINE S06 (Bottom View) (Top View) 2 +0.10 0.2 -0.05 0.65 1 1.3 PIN NO. 0.1 MIN 0.9 0.1 0.7 0.15 +0.10 -0.05 LNA SW SC O /N TX DI PA 5 5 2 6 6 1 PIN NAME 1 Input 2 GND 3 GND 4 Output 5 GND 6 VCC NT SYSTEM APPLICATION EXAMPLE RX 3 IN Note: All dimensions are typical unless otherwise specified. Location examples in digital cellular 4 UE 0.65 0 to 0.1 4 D 3 1.25 0.1 2.0 0.2 C3B 2.1 0.1 I Q DEMOD PLL PLL I 0 90 Q ORDERING INFORMATION Part Number Quantity UPC8178TB-E3-A 3 K pcs/reel Note: Embossed tape, 8 mm wide. Pins 1, 2 and 3 face the tape Life Support Applications perforation side. These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and agree to fully indemnify CEL for all damages resulting from such improper use or sale. EXCLUSIVE NORTH AMERICAN AGENT FOR RF, MICROWAVE & OPTOELECTRONIC SEMICONDUCTORS CALIFORNIA EASTERN LABORATORIES * Headquarters * 4590 Patrick Henry Drive * Santa Clara, CA 95054-1817 * (408) 988-3500 * Telex 34-6393 * FAX (408) 988-0279 24-Hour Fax-On-Demand: 800-390-3232 (U.S. and Canada only) * Internet: http://WWW.CEL.COM 06/20/2001 DATA SUBJECT TO CHANGE WITHOUT NOTICE D 4590 Patrick Henry Drive Santa Clara, CA 95054-1817 Telephone: (408) 919-2500 Facsimile: (408) 988-0279 UE Subject: Compliance with EU Directives CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive 2003/11/EC Restriction on Penta and Octa BDE. IN CEL Pb-free products have the same base part number with a suffix added. The suffix -A indicates that the device is Pb-free. The -AZ suffix is used to designate devices containing Pb which are exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals. All devices with these suffixes meet the requirements of the RoHS directive. Restricted Substance per RoHS Lead (Pb) Mercury Concentration Limit per RoHS (values are not yet fixed) < 1000 PPM Concentration contained in CEL devices -A Not Detected < 1000 PPM Not Detected < 100 PPM Not Detected SC O Cadmium NT This status is based on CEL's understanding of the EU Directives and knowledge of the materials that go into its products as of the date of disclosure of this information. Hexavalent Chromium < 1000 PPM Not Detected PBB < 1000 PPM Not Detected PBDE < 1000 PPM Not Detected -AZ (*) If you should have any additional questions regarding our devices and compliance to environmental standards, please do not hesitate to contact your local representative. DI Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall CEL's liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to customer on an annual basis. See CEL Terms and Conditions for additional clarification of warranties and liability. 5-146 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: CEL: UPC8178TB-EV09 UPC8178TB-EV24 UPC8178TB-EV19