TVS Diodes Surface Mount - 200W > SMF3.3 Series SMF3.3 RoHS Pb e3 Description SMF3.3 is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Features *2 00W peak pulse power capability at 10/1000s waveform, repetition rate (duty cycle): 0.01% *1 200W peak pulse power capability at 8/20us waveform * Excellent clamping capability *C ompatible with industrial standard package SOD123FL ow profile: maximum *L height of 1.08mm. *F or surface mounted applications to optimize board space * Typical failure mode is short from over-specified voltage or current * Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4c * IEC-61000-4-2 ESD 30kV(Air), 30kV (Contact) Uni-directional Agency Approvals AGENCY AGENCY FILE NUMBER E230531 Maximum Ratings and Thermal Characteristics (TA=25OC unless otherwise noted) Parameter Symbol Peak Pulse Power Dissipation at TA=25C (Note 1) 8/20s PPPM 10/1000s Value Unit 1200 W 200 W Thermal Resistance Junction- toAmbient RJA 220 C/W Thermal Resistance Junction- to- Lead RJL 100 C/W TJ -55 to 150 C TSTG -55 to 150 C Operating Temperature Range Storage Temperature Range *E SD protection of data lines in accordance with IEC 61000-4-2 *E FT protection of data lines in accordance with IEC 61000-4-4 *F ast response time: typically less than 1.0ns from 0 Volts to VBR min *H igh temperature soldering: 260C/40 seconds at terminals * Built-in strain relief *M eet MSL level1, per J-STD-020C, LF maximun peak of 260C *M atte tin lead-free plated * Halogen-free and RoHS compliant * Pb-free E3 means 2nd level interconnect is Pb-free and the terminal finish material is tin(Sn) (IPC/ JEDEC J-STD-609A.01) Notes: 1. Non-repetitive current pulse, per Fig. 4 & 6 and derated above TJ (initial) =25C per Fig. 3. Functional Diagram Applications Bi-directional Cathode SMF3.3 devices are ideal for the protection of portable devices/hard drives, notebooks, VCC busses, POS terminal, SSDs, power supplies, monitors, and vulnerable circuit used in other consumer applications. Anode Uni-directional Electrical Characteristics (T =25C unless otherwise noted) A Part Number SMF3.3 Marking Code 33 Breakdown Voltage VBR (Volts) @ IT MIN MAX Test Current IT (mA) 3.4 4.3 10 Reverse Stand off Voltage VR (V) Maximum Reverse Leakage @ VR IR (A) Maximum Peak Pulse Current (10/1000S) Ipp (A) 3.3 0.5 30.0 Maximum Clamping Voltage @Ipp (10/1000S) VC (V) 6.8 Maximum Peak Pulse Current (8/20S) Ipp (A) 120.0 Maximum Clamping Voltage @Ipp (8/20S) VC (V) 10.0 Notes: 1. VBR measured after IT applied for 300s, IT = sequare wave pulse or equivalent. 2. Surge current waveform per 10/1000s exponential wave and derated per Fig.2. 3. All terms and symbols are consistent with ANSI/IEEE C62.35. 4. Surge current waveform per 8/20s exponential wave and derated per Fig.6. (c)2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 07/28/16 TVSDiodes Diodes TVS Surface Mount - 200W > SMF3.3 Series I-V Curve Characteristics PPPM Peak Pulse Power Dissipation -- Max power dissipation VR Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation VBR Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (IT) VC Clamping Voltage -- Peak voltage measured across the TVS at a specified Ippm (peak impulse current) IR Reverse Leakage Current -- Current measured at VR VF Forward Voltage Drop for Uni-directional note: VF distribution range from 10V to 15V Uni-directional Vc VBR VR IR IT VF V Ipp Ratings and Characteristic Curves (T =25C unless otherwise noted) A Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating Curve Voltage Transients 10 PPPM-Peak Pulse Power (kW) TJ initial = Tamb Voltage or Current Voltage Across TVS Current Through TVS 1 0.1 0.001 0.01 Figure 3 - Peak Pulse Power Derating Curve IPPM- Peak Pulse Current, % IRSM Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % 150 80 60 40 20 0 25 50 75 100 125 150 TJ - Initial Junction Temperature (C) (c)2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 07/28/16 1 Figure 4 - 10/1000S Pulse Waveform 100 0 0.1 td-Pulse Width (ms) Time 175 tr=10sec TJ=25C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM Peak Value IPPM 100 Half Value IPPM IPPM ( ) 2 50 0 10/1000sec. Waveform as defined by R.E.A td 0 1.0 2.0 t-Time (ms) 3.0 4.0 TVS Diodes Surface Mount - 200W > SMF3.3 Series Figure 5 - Capacitance vs. Reverse Bias Figure 6 - 8/20S Pulse Waveform 120 110% 100% 90% 80% 80 Percent of IPP Capacitance (pF) 100 60 40 70% 60% 50% 40% 30% 20 20% 10% 0 0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3 0% 3.3 0.0 5.0 10.0 15.0 20.0 25.0 30.0 Time (s) Bias Voltage (V) Soldering Parameters Pre Heat Lead-free assembly - Temperature Min (Ts(min)) 150C - Temperature Max (Ts(max)) 200C - Time (min to max) (ts) 60 - 180 secs Average ramp up rate (Liquidus Temp (TA) to peak 3C/second max TS(max) to TA - Ramp-up Rate 3C/second max Reflow - Temperature (TA) (Liquidus) 217C - Time (min to max) (ts) 60 - 150 seconds Peak Temperature (TP) 260+0/-5 C Time within 5C of actual peak Temperature (tp) 20 - 40 seconds Ramp-down Rate 6C/second max Time 25C to peak Temperature (TP) 8 minutes Max. Do not exceed 260C tp TP Ramp-up TL Temperature (T) Reflow Condition tL Critical Zone TL to TP Ts(max) Ts(min) Ramp-down ts Preheat 25C t 25C to Peak Time (t) High Reliability Test Specification Pre-condition (HTRB/ TC/ PCT/ H3TRB) (1) Bake 24hrs @150C (2)168hrs @85% RH and 85C (3) IR reflow,3 reflows, peak temperature of 260C HTRB JESD 22-108C VCC bias= 80%VDRM & TA=150C, 1008hrs Physical Specifications Case SOD-123FL plastic over passivated junction Temperature Cycling MIL-STD-883F, Method 1010.8 Condition C -65C to150C, 1000 cycles Polarity Color band denotes cathode except bipolar Pressure Cooker JEDEC 22-A102C 100%RH @121C @15psi, 96hrs Terminal Matte tin-plated leads, solderable per JESD22-B102 Bias Humidity (H3TRB) JESD 22-A101B Vcc bias (pin1to pin3)=VDRM ,85%RH, 85C , 1008 hours RSH JESD 22-A111 260C ,10 secs. (c)2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 07/28/16 TVSDiodes Diodes TVS Surface Mount - 200W > SMF3.3 Series Dimensions - SOD-123FL Package Max 2.90 3.10 0.114 0.122 B 3.50 3.90 0.138 0.154 C 0.85 1.05 0.033 0.041 D 1.70 2.00 0.067 0.079 F E 0.43 0.83 0.017 0.033 E Min B A Inches Max A C Millimeters Min E Dimensions G H D F 0.10 0.25 0.004 0.010 G 0.00 0.10 0.000 0.004 H 0.90 1.08 0.035 0.043 Mounting Pad Layout 1.6 (0.062) 1.3 (0.051) 1.4 (0.055) Part Numbering System Part Marking System SMF 3.3 LF VR VOLTAGE SERIES 33 YM Cathode Band Marking Code Trace Code Marking Y:Year Code M: Month Code Packaging Options Part number SMF3.3 Component Package SOD-123FL Quantity 3000 Packaging Option Tape & Reel - 8mm tape/7" reel Packaging Specification EIA RS-481 Tape and Reel Specification 0.157 (4.0) Cathode 0.31 (8.0) 0.157 (4.0) 0.059 DIA (1.5) Cover tape Optional 7" 7.0 (178) 0.80 (20.2) Arbor Hole Dia. 0.33 (8.5) (c)2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 07/28/16 Dimensions are in inches (and millimeters). Direction of Feed