HCS12
Microcontrollers
freescale.com
MC9S12KG128
Data Sheet
MC9S12KG128
Rev. 1.16
06/2010
To provide the most up-to-date information, the revision of our documents on the World Wide Web will be
the most current. Your printed copy may be an earlier revision. To verify you have the latest information
available, refer to:
http://freescale.com/
A full list of family members and options is included in the appendices.
The following revision history table summarizes changes contained in this document.
This document contains information for all constituent modules, with the exception of the CPU. For CPU
information please refer to CPU12-1 in the CPU12 & CPU12X Reference Manual.
Revision History
Date Revision
Level Description
June, 2010 1.16
Change SCI from V1 to V2, Chagne ATD from V1 to V3.
Update TIM block guide.
Update mask set Table 1-7, add Section 1.7 ATD External Trigger Input
Connection
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 3
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1) . . . . . . .17
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1). . . . . . .73
Chapter 3 2 Kbyte EEPROM Module (S12EETS2KV1) . . . . . . . . . . . . . .117
Chapter 4 Port Integration Module (PIM9KG128V1) . . . . . . . . . . . . . . . .137
Chapter 5 Clocks and Reset Generator (CRGV4) Block Description . .177
Chapter 6 Pierce Oscillator (S12OSCLCPV1) . . . . . . . . . . . . . . . . . . . . .213
Chapter 7 Analog-to-Digital Converter (ATD10B16CV3) . . . . . . . . . . . .219
Chapter 8 Inter-Integrated Circuit (IICV2) . . . . . . . . . . . . . . . . . . . . . . . .249
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2).
273
Chapter 10 Serial Communications Interface (S12SCIV2) . . . . . . . . . . . .329
Chapter 11 Serial Peripheral Interface (SPIV3) . . . . . . . . . . . . . . . . . . . . .359
Chapter 12 Pulse-Width Modulator (S12PWM8B8CV1) . . . . . . . . . . . . . .381
Chapter 13 Timer Module (TIM16B8CV1) . . . . . . . . . . . . . . . . . . . . . . . . .413
Chapter 14 Dual Output Voltage Regulator (VREG3V3V2) . . . . . . . . . . .441
Chapter 15 Background Debug Module (BDMV4) . . . . . . . . . . . . . . . . . .449
Chapter 16 Debug Module (DBGV1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .475
Chapter 17 Interrupt (INTV1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .507
Chapter 18 Multiplexed External Bus Interface (MEBIV3) . . . . . . . . . . . .515
Chapter 19 Module Mapping Control (MMCV4) . . . . . . . . . . . . . . . . . . . .545
Appendix A Electrical Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . .565
Appendix B Recommended PCB Layout . . . . . . . . . . . . . . . . . . . . . . . . . .599
Appendix C Package Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .602
MC9S12KG128 Data Sheet, Rev. 1.16
4 Freescale Semiconductor
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 5
Chapter 1
MC9S12KG128 Device Overview (MC9S12KG128V1)
1.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
1.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
1.1.2 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
1.1.3 MC9S12KG128 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
1.2 Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
1.2.1 Signal Properties Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
1.2.2 Detailed Signal Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
1.2.3 Power Supply Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
1.3 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
1.3.1 Device Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
1.3.2 Detailed Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
1.3.3 Part ID Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
1.4 System Clock Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
1.5 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
1.5.1 Chip Configuration Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
1.5.2 Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
1.5.3 Low Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
1.6 Resets and Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
1.6.1 Vectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
1.6.2 Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
1.7 ATD External Trigger Input Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Chapter 2
128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
2.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
2.1.1 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
2.1.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
2.1.3 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
2.1.4 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
2.2 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
2.3 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
2.3.1 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
2.3.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
2.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
2.4.1 Flash Command Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
2.5 Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
2.5.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
2.5.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
MC9S12KG128 Data Sheet, Rev. 1.16
6 Freescale Semiconductor
2.5.3 Background Debug Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
2.6 Flash Module Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
2.6.1 Unsecuring the MCU using Backdoor Key Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
2.6.2 Unsecuring the Flash Module in Special Single-Chip Mode using BDM . . . . . . . . . . . 113
2.7 Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
2.7.1 Flash Reset Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
2.7.2 Reset While Flash Command Active . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
2.8 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
2.8.1 Description of Flash Interrupt Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Chapter 3
2 Kbyte EEPROM Module (S12EETS2KV1)
3.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
3.1.1 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
3.1.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
3.1.3 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
3.1.4 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
3.2 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
3.3 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
3.3.1 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
3.3.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
3.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
3.4.1 Program and Erase Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
3.5 Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
3.5.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
3.5.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
3.5.3 Background Debug Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
3.6 Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
3.7 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Chapter 4
Port Integration Module (PIM9KG128V1)
4.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
4.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
4.1.2 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
4.2 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
4.2.1 Signal Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
4.3 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
4.3.1 Port T Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
4.3.2 Port S Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
4.3.3 Port M Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
4.3.4 Port P Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
4.3.5 Port H Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
4.3.6 Port J Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 7
4.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
4.4.1 I/O Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
4.4.2 Input Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
4.4.3 Data Direction Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
4.4.4 Reduced Drive Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
4.4.5 Pull Device Enable Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
4.4.6 Polarity Select Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
4.4.7 Pin Configuration Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
4.5 Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
4.5.1 Reset Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
4.6 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
4.6.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
4.6.2 Interrupt Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
4.6.3 Operation in Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
Chapter 5
Clocks and Reset Generator (CRGV4) Block Description
5.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
5.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
5.1.2 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
5.1.3 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
5.2 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
5.2.1 VDDPLL, VSSPLL — PLL Operating Voltage, PLL Ground . . . . . . . . . . . . . . . . . . . . . . 179
5.2.2 XFC — PLL Loop Filter Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
5.2.3 RESET — Reset Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
5.3 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
5.3.1 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
5.3.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
5.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
5.4.1 Phase Locked Loop (PLL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
5.4.2 System Clocks Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
5.4.3 Clock Monitor (CM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
5.4.4 Clock Quality Checker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
5.4.5 Computer Operating Properly Watchdog (COP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198
5.4.6 Real-Time Interrupt (RTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199
5.4.7 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199
5.4.8 Low-Power Operation in Run Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200
5.4.9 Low-Power Operation in Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200
5.4.10 Low-Power Operation in Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204
5.5 Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208
5.5.1 Clock Monitor Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210
5.5.2 Computer Operating Properly Watchdog (COP) Reset . . . . . . . . . . . . . . . . . . . . . . . . . 210
5.5.3 Power-On Reset, Low Voltage Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211
5.6 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212
5.6.1 Real-Time Interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212
MC9S12KG128 Data Sheet, Rev. 1.16
8 Freescale Semiconductor
5.6.2 PLL Lock Interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212
5.6.3 Self-Clock Mode Interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212
Chapter 6
Pierce Oscillator (S12OSCLCPV1)
6.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213
6.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213
6.1.2 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213
6.1.3 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214
6.2 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214
6.2.1 VDDPLL and VSSPLL — Operating and Ground Voltage Pins . . . . . . . . . . . . . . . . . . . . 214
6.2.2 EXTAL and XTAL — Input and Output Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214
6.2.3 XCLKS — Input Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216
6.3 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216
6.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216
6.4.1 Gain Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216
6.4.2 Clock Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216
6.4.3 Wait Mode Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
6.4.4 Stop Mode Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
Chapter 7
Analog-to-Digital Converter (ATD10B16CV3)
Block Description
7.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219
7.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219
7.1.2 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219
7.1.3 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219
7.2 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221
7.2.1 ANx (x = 15, 14, 13, 12, 11, 10, 9, 8, 7, 6, 5, 4, 3, 2, 1, 0) Analog Input Channel xPins
221
7.2.2 ETRIG — External Trigger Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221
7.2.3 VRH, VRL — High Reference Voltage Pin, Low Reference Voltage Pin . . . . . . . . . . . . 221
7.2.4 VDDA, VSSA — Analog Circuitry Power Supply Pins . . . . . . . . . . . . . . . . . . . . . . . . . 221
7.3 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221
7.3.1 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221
7.3.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223
7.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245
7.4.1 Analog Sub-block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245
7.4.2 Digital Sub-Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246
7.4.3 Operation in Low Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247
7.5 Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 248
7.6 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 248
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 9
Chapter 8
Inter-Integrated Circuit (IICV2) Block Description
8.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249
8.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249
8.1.2 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251
8.1.3 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251
8.2 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252
8.2.1 IIC_SCL — Serial Clock Line Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252
8.2.2 IIC_SDA — Serial Data Line Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252
8.3 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252
8.3.1 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252
8.3.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253
8.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 264
8.4.1 I-Bus Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 264
8.4.2 Operation in Run Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268
8.4.3 Operation in Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268
8.4.4 Operation in Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268
8.5 Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268
8.6 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268
8.7 Initialization/Application Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 269
8.7.1 IIC Programming Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 269
Chapter 9
Freescale’s Scalable Controller Area Network (S12MSCANV2)
9.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273
9.1.1 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273
9.1.2 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274
9.1.3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274
9.1.4 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275
9.2 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275
9.2.1 RXCAN — CAN Receiver Input Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275
9.2.2 TXCAN — CAN Transmitter Output Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275
9.2.3 CAN System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275
9.3 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276
9.3.1 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276
9.3.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278
9.3.3 Programmer’s Model of Message Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300
9.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309
9.4.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309
9.4.2 Message Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 310
9.4.3 Identifier Acceptance Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313
9.4.4 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319
9.4.5 Low-Power Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320
9.4.6 Reset Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325
MC9S12KG128 Data Sheet, Rev. 1.16
10 Freescale Semiconductor
9.4.7 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325
9.5 Initialization/Application Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327
9.5.1 MSCAN initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327
Chapter 10
Serial Communications Interface (S12SCIV2)
Block Description
10.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329
10.1.1 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329
10.1.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 330
10.1.3 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 330
10.1.4 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 331
10.2 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332
10.2.1 TXD-SCI Transmit Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332
10.2.2 RXD-SCI Receive Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332
10.3 Memory Map and Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333
10.3.1 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333
10.3.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333
10.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 341
10.4.1 Data Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 342
10.4.2 Baud Rate Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 343
10.4.3 Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 344
10.4.4 Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 347
10.4.5 Single-Wire Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 356
10.4.6 Loop Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 356
10.5 Initialization Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 356
10.5.1 Reset Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 356
10.5.2 Interrupt Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 357
10.5.3 Recovery from Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 358
Chapter 11
Serial Peripheral Interface (SPIV3) Block Description
11.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 359
11.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 359
11.1.2 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 359
11.1.3 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360
11.2 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360
11.2.1 MOSI — Master Out/Slave In Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360
11.2.2 MISO — Master In/Slave Out Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 361
11.2.3 SS — Slave Select Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 361
11.2.4 SCK — Serial Clock Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 361
11.3 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 361
11.3.1 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 361
11.3.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 362
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 11
11.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 369
11.4.1 Master Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370
11.4.2 Slave Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 371
11.4.3 Transmission Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 372
11.4.4 SPI Baud Rate Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375
11.4.5 Special Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 376
11.4.6 Error Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 377
11.4.7 Operation in Run Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 378
11.4.8 Operation in Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 378
11.4.9 Operation in Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 378
11.5 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 379
11.6 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 379
11.6.1 MODF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 379
11.6.2 SPIF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 379
11.6.3 SPTEF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 379
Chapter 12
Pulse-Width Modulator (S12PWM8B8CV1)
12.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 381
12.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 381
12.1.2 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 381
12.1.3 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 382
12.2 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 382
12.2.1 PWM7 — PWM Channel 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 382
12.2.2 PWM6 — PWM Channel 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 382
12.2.3 PWM5 — PWM Channel 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383
12.2.4 PWM4 — PWM Channel 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383
12.2.5 PWM3 — PWM Channel 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383
12.2.6 PWM3 — PWM Channel 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383
12.2.7 PWM3 — PWM Channel 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383
12.2.8 PWM3 — PWM Channel 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383
12.3 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383
12.3.1 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383
12.3.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 384
12.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 399
12.4.1 PWM Clock Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 399
12.4.2 PWM Channel Timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 402
12.5 Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 410
12.6 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 411
Chapter 13
Timer Module (TIM16B8CV1) Block Description
13.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 413
13.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 413
MC9S12KG128 Data Sheet, Rev. 1.16
12 Freescale Semiconductor
13.1.2 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 413
13.1.3 Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 414
13.2 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 416
13.2.1 IOC7 — Input Capture and Output Compare Channel 7 Pin . . . . . . . . . . . . . . . . . . . . 416
13.2.2 IOC6 — Input Capture and Output Compare Channel 6 Pin . . . . . . . . . . . . . . . . . . . . 416
13.2.3 IOC5 — Input Capture and Output Compare Channel 5 Pin . . . . . . . . . . . . . . . . . . . . 416
13.2.4 IOC4 — Input Capture and Output Compare Channel 4 Pin . . . . . . . . . . . . . . . . . . . . 416
13.2.5 IOC3 — Input Capture and Output Compare Channel 3 Pin . . . . . . . . . . . . . . . . . . . . 416
13.2.6 IOC2 — Input Capture and Output Compare Channel 2 Pin . . . . . . . . . . . . . . . . . . . . 417
13.2.7 IOC1 — Input Capture and Output Compare Channel 1 Pin . . . . . . . . . . . . . . . . . . . . 417
13.2.8 IOC0 — Input Capture and Output Compare Channel 0 Pin . . . . . . . . . . . . . . . . . . . . 417
13.3 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 417
13.3.1 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 417
13.3.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 419
13.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 435
13.4.1 Prescaler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 436
13.4.2 Input Capture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 437
13.4.3 Output Compare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 437
13.4.4 Pulse Accumulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 438
13.4.5 Event Counter Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 438
13.4.6 Gated Time Accumulation Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 439
13.5 Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 439
13.6 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 439
13.6.1 Channel [7:0] Interrupt (C[7:0]F) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 439
13.6.2 Pulse Accumulator Input Interrupt (PAOVI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 440
13.6.3 Pulse Accumulator Overflow Interrupt (PAOVF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 440
13.6.4 Timer Overflow Interrupt (TOF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 440
Chapter 14
Dual Output Voltage Regulator (VREG3V3V2)
Block Description
14.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 441
14.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 441
14.1.2 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 441
14.1.3 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 442
14.2 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 443
14.2.1 VDDR — Regulator Power Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 443
14.2.2 VDDA, VSSA — Regulator Reference Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 443
14.2.3 VDD, VSS — Regulator Output1 (Core Logic) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 444
14.2.4 VDDPLL, VSSPLL — Regulator Output2 (PLL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 444
14.2.5 VREGEN — Optional Regulator Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 444
14.3 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 444
14.3.1 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 444
14.3.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 445
14.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 445
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 13
14.4.1 REG — Regulator Core . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 446
14.4.2 Full-Performance Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 446
14.4.3 Reduced-Power Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 446
14.4.4 LVD — Low-Voltage Detect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 446
14.4.5 POR — Power-On Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 446
14.4.6 LVR — Low-Voltage Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 446
14.4.7 CTRL — Regulator Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 446
14.5 Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 447
14.5.1 Power-On Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 447
14.5.2 Low-Voltage Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 447
14.6 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 447
14.6.1 LVI — Low-Voltage Interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 447
Chapter 15
Background Debug Module (BDMV4) Block Description
15.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 449
15.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 449
15.1.2 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 450
15.2 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 450
15.2.1 BKGD — Background Interface Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 451
15.2.2 TAGHI — High Byte Instruction Tagging Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 451
15.2.3 TAGLO — Low Byte Instruction Tagging Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 451
15.3 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 452
15.3.1 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 452
15.3.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 453
15.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 458
15.4.1 Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 458
15.4.2 Enabling and Activating BDM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 458
15.4.3 BDM Hardware Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 459
15.4.4 Standard BDM Firmware Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 460
15.4.5 BDM Command Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 461
15.4.6 BDM Serial Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 463
15.4.7 Serial Interface Hardware Handshake Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 466
15.4.8 Hardware Handshake Abort Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 468
15.4.9 SYNC — Request Timed Reference Pulse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 471
15.4.10Instruction Tracing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 471
15.4.11Instruction Tagging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 472
15.4.12Serial Communication Time-Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 472
15.4.13Operation in Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 473
15.4.14Operation in Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 473
Chapter 16
Debug Module (DBGV1) Block Description
16.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 475
MC9S12KG128 Data Sheet, Rev. 1.16
14 Freescale Semiconductor
16.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 475
16.1.2 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 477
16.1.3 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 477
16.2 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 479
16.3 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 480
16.3.1 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 480
16.3.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 480
16.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 496
16.4.1 DBG Operating in BKP Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 496
16.4.2 DBG Operating in DBG Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 498
16.4.3 Breakpoints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 505
16.5 Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 506
16.6 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 506
Chapter 17
Interrupt (INTV1) Block Description
17.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 507
17.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 508
17.1.2 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 508
17.2 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 509
17.3 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 509
17.3.1 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 509
17.3.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 509
17.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 511
17.4.1 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 512
17.5 Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 512
17.6 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 512
17.6.1 Interrupt Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 512
17.6.2 Highest Priority I-Bit Maskable Interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 512
17.6.3 Interrupt Priority Decoder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 513
17.7 Exception Priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 513
Chapter 18
Multiplexed External Bus Interface (MEBIV3)
18.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 515
18.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 515
18.1.2 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 517
18.2 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 517
18.3 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 519
18.3.1 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 520
18.3.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 520
18.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 537
18.4.1 Detecting Access Type from External Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 537
18.4.2 Stretched Bus Cycles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 538
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 15
18.4.3 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 538
18.4.4 Internal Visibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 543
18.4.5 Low-Power Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 543
Chapter 19
Module Mapping Control (MMCV4) Block Description
19.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 545
19.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 546
19.1.2 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 546
19.2 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 546
19.3 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 546
19.3.1 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 546
19.3.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 548
19.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 558
19.4.1 Bus Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 558
19.4.2 Address Decoding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 558
19.4.3 Memory Expansion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 560
Appendix A
Electrical Characteristics
A.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 565
A.1.1 Parameter Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 565
A.1.2 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 565
A.1.3 Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 566
A.1.4 Current Injection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 566
A.1.5 Absolute Maximum Ratings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 567
A.1.6 ESD Protection and Latch-up Immunity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 568
A.1.7 Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 569
A.1.8 Power Dissipation and Thermal Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 570
A.1.9 I/O Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 572
A.1.10 Supply Currents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 574
A.2 Voltage Regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 576
A.3 Chip Power-up and LVI/LVR Graphical Explanation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 577
A.4 Output Loads. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 578
A.4.1 Resistive Loads. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 578
A.4.2 Capacitive Loads. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 578
A.5 ATD Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 579
A.5.1 ATD Operating Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 579
A.5.2 Factors Influencing Accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 580
A.5.3 ATD Accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 581
A.6 NVM, Flash and EEPROM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 584
A.6.1 NVM Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 584
A.6.2 NVM Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 586
A.7 Reset, Oscillator and PLL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 587
MC9S12KG128 Data Sheet, Rev. 1.16
16 Freescale Semiconductor
A.7.1 Startup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 587
A.7.2 Oscillator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 588
A.7.3 Phase Locked Loop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 589
A.8 MSCAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 593
A.9 SPI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 593
A.9.1 Master Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 593
A.9.2 Slave Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 595
A.10 External Bus Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 596
A.10.1 General Muxed Bus Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 596
Appendix B
Recommended PCB Layout
Appendix C
Package Information
C.1 112-Pin LQFP Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 603
C.2 80-Pin QFP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 604
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 17
Chapter 1
MC9S12KG128 Device Overview (MC9S12KG128V1)
1.1 Introduction
The MC9S12KG128 is a 112/80 pin 16-bit Flash-based microcontroller family targeted for high reliability
systems. The MC9S12KG128 has an increased performance in reliability over the life of the product due
to a built-in Error Checking and Correction Code (ECC) in the Flash memory. The program and erase
operations automatically generate six parity bits per word making ECC transparent to the user.
The MC9S12KG128 is comprised of standard on-chip peripherals including a 16-bit central processing
unit (CPU12), 128K bytes of Flash EEPROM, 2K bytes of EEPROM, 8K bytes of RAM, two
asynchronous serial communications interface (SCI), three serial peripheral interface (SPI), IIC-bus, an
8-channel IC/OC timer, one 16-channel 10-bit analog-to-digital converter (ADC), an 8-channel
pulse-width modulator (PWM), two CAN 2.0 A, B software compatible modules, 29 discrete digital I/O
channels (Port A, Port B, Port E and Port K), and 20 discrete digital I/O lines with interrupt and wakeup
capability. The MC9S12KG128 has full 16-bit data paths throughout, however, the external bus can
operate in an 8-bit narrow mode so single 8-bit wide memory can be interfaced for lower cost systems. The
inclusion of a PLL circuit allows power consumption and performance to be adjusted to suit operational
requirements.
1.1.1 Features
HCS12 Core
16-bit HCS12 CPU
Upward compatible with M68HC11 instruction set
Interrupt stacking and programmer’s model identical to M68HC11
Instruction queue
Enhanced indexed addressing
MEBI (Multiplexed External Bus Interface)
MMC (Memory Map and Interface)
INT (Interrupt Controller)
DBG (Debugger)
BDM (Background Debug Mode)
Oscillator
4MHz to 16MHz frequency range
Pierce with amplitude loop control
Clock monitor
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
18 Freescale Semiconductor
Clock and Reset Generator (CRG)
Phase-locked loop clock frequency multiplier
Self Clock mode in absence of external clock
COP watchdog
Real Time interrupt (RTI)
Memory
128K Byte Flash EEPROM
Internal program/erase voltage generation
Security and Block Protect bits
Hamming Error Correction Coding (ECC)
2K Byte EEPROM
8K Byte static RAM
Single-cycle misaligned word accesses without wait states
Analog-to-Digital Converter (ADC)
One 16-channel module with 10-bit resolution
External conversion trigger capability
8-channel Timer (TIM)
Programmable input capture or output compare channels
Simple PWM mode
Counter Modulo Reset
External Event Counting
Gated Time Accumulation
8-channel Pulse Width Modulator (PWM)
Programmable period and duty cycle per channel
8-bit 8-channel or 16-bit 4-channel
Edge and center aligned PWM signals
Emergency shutdown input
Two 1M bit per second, CAN 2.0 A, B software compatible modules
Five receive and three transmit buffers
Flexible identifier filter programmable as 2 x 32 bit, 4 x 16 bit or 8 x 8 bit
Four separate interrupt channels for Rx, Tx, error and wake-up
Low-pass filter wake-up function
Loop-back for self test operation
Serial interfaces
Two asynchronous serial communication interface (SCI)
Three synchronous serial peripheral interface (SPI)
Inter-IC Bus (IIC)
Internal 2.5V Regulator
Input voltage range from 3.15V to 5.5V
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 19
Low power mode capability
Low Voltage Reset (LVR) and Low Voltage Interrupt (LVI)
20 key wake up inputs
Rising or falling edge triggered interrupt capability
Digital filter to prevent short pulses from triggering interrupts
Programmable pull ups and pull downs
Operating frequency for ambient temperatures (TA -40°C to 125°C)
50MHz equivalent to 25MHz Bus Speed
112-Pin LQFP or 80-Pin QFP package
I/O lines with 3.3V/5V input and drive capability
3.3V/5V A/D converter inputs
1.1.2 Modes of Operation
Normal modes
Normal Single-Chip Mode
Normal Expanded Wide Mode
Normal Expanded Narrow Mode
Emulation Expanded Wide Mode
Emulation Expanded Narrow Mode
Special Operating Modes
Special Single-Chip Mode with active Background Debug Mode
Special Test Mode (Freescale use only)
Special Peripheral Mode (Freescale use only)
Each of the above modes of operation can be configured for three Low power submodes
Stop Mode
Pseudo Stop Mode
Wait Mode
Secure operation, preventing the unauthorized read and write of the memory contents.
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
20 Freescale Semiconductor
Table 1-1 shows a feature overview of the MC9S12KG128 members.
Figure 1-1 shows the part number coding based on the package and temperature options for the
MC9S12KG128.
Figure 1-1. Order Part number Coding
Table 1-1. List of MC9S12KG128 members
Device Temp Options1
1C: TA = 85˚C, f = 25MHz. V: TA=105˚C, f = 25MHz. M: TA= 125˚C, f = 25MHz
Flash RAM EEPROM Package CAN SCI SPI IIC A/D2
2Number of channels
PWM2TIM2I/O3
3I/O is the sum of ports capable to act as digital input or output.
MC9S12KG128 C, V, M 128K 8K 2K 112 LQFP 2 2 3 1 16 8 8 91
80 QFP 2 2 3 1 8 7 8 59
MC9S12KL128 C, V, M 128K 6K 2K 112 LQFP 1 2 2 1 16 8 8 91
80 QFP 1 1 2 1 8 7 8 59
MC9S12KL64 C, V, M 64K 4K 1K 112 LQFP 1 2 2 1 16 8 8 91
80 QFP 1 1 2 1 8 7 8 59
MC9S12KL32 C, V, M 32K 2K 1K 80 QFP 1 1 2 1 8 7 8 59
MC9S12KC128 C, V, M 128K 6K None 112 LQFP 1 2 2 1 16 8 8 91
80 QFP 1 1 2 1 8 7 8 59
MC9S12KC64 C, V, M 64K 4K None 112 LQFP 1 2 2 1 16 8 8 91
80 QFP 1 1 2 1 8 7 8 59
MC9S12 KG128 C FU
Package Option
Temperature Option
Device Title
Controller Family
Temperature Options
C = -40˚C to 85˚C
V = -40˚C to 105˚C
M = -40˚C to 125˚C
Package Options
PV = 112LQFP
FU = 80QFP
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 21
1.1.3 MC9S12KG128 Block Diagram
Figure 1-2. MC9S12KG128 Block Diagram
128K Byte Flash EEPROM
8K Byte RAM
RESET
EXTAL
XTAL
VDD1,2
VSS1,2
SCI0
BKGD
R/W
MODB
XIRQ
NOACC/XCLKS
System
Integration
Module
(SIM)
VDDR
CPU12
Periodic Interrupt
COP Watchdog
Clock Monitor
Single-Wire BDM
Breakpoints
PLL
VSSPLL
XFC
VDDPLL
Multiplexed Address/Data Bus
ATD
Multiplexed
Wide Bus
Multiplexed
VDDX
VSSX
Internal Logic 2.5V
Narrow Bus
PPAGE
VDDPLL
VSSPLL
OSC/PLL 2.5V
IRQ
LSTRB
ECLK
MODA
PA4
PA3
PA2
PA1
PA0
PA7
PA6
PA5
TEST
ADDR12
ADDR11
ADDR10
ADDR9
ADDR8
ADDR15
ADDR14
ADDR13
DATA12
DATA11
DATA10
DATA9
DATA8
DATA15
DATA14
DATA13
PB4
PB3
PB2
PB1
PB0
PB7
PB6
PB5
ADDR4
ADDR3
ADDR2
ADDR1
ADDR0
ADDR7
ADDR6
ADDR5
DATA4
DATA3
DATA2
DATA1
DATA0
DATA7
DATA6
DATA5
DATA4
DATA3
DATA2
DATA1
DATA0
DATA7
DATA6
DATA5
PE3
PE4
PE5
PE6
PE7
PE0
PE1
PE2
AN02
AN06
AN00
AN07
AN01
AN03
AN04
AN05
PAD03
PAD04
PAD05
PAD06
PAD07
PAD00
PAD01
PAD02
IOC2
IOC6
IOC0
IOC7
IOC1
IOC3
IOC4
IOC5
PT3
PT4
PT5
PT6
PT7
PT0
PT1
PT2
VRH
VRL
VDDA
VSSA
VRH
VRL
AN10
AN14
AN08
AN15
AN09
AN11
AN12
AN13
PAD11
PAD12
PAD13
PAD14
PAD15
PAD08
PAD09
PAD10
VDDA
VSSA
RXD
TXD
MISO
MOSI
PS3
PS4
PS5
PS0
PS1
PS2
SCI1 RXD
TXD
PWM2
PWM6
PWM0
PWM7
PWM1
PWM3
PWM4
PWM5
PP3
PP4
PP5
PP6
PP7
PP0
PP1
PP2
PIX2
PIX0
PIX1
PIX3
ECS
PK3
PK7
PK0
PK1
XADDR17
ECS
XADDR14
XADDR15
XADDR16
SCK
SS PS6
PS7
SPI0
IIC SDA
SCL PJ6
PJ7
CAN0 RxCAN
TxCAN PM1
PM0
PM2
PM3
PM4
PM5
PM6
PM7
KWH2
KWH6
KWH0
KWH7
KWH1
KWH3
KWH4
KWH5
PH3
PH4
PH5
PH6
PH7
PH0
PH1
PH2
KWJ0
KWJ1 PJ0
PJ1
I/O Driver 3.3V/5V
VDDA
VSSA
A/D Converter 3.3V/5V
DDRA DDRB
PTA PTB
DDRE
PTE
PAD
PAD
PTK
DDRK
PTT
DDRT
PTP
DDRP
PTS
DDRS
PTM
DDRM
PTH
DDRH
PTJ
DDRJ
PK2
CRG
Voltage Regulator
VSSR
VDD1,2
VSS1,2
VREGEN
VDDR
VSSR
Voltage Regulator 3.3V/5V
PIX4
PIX5 PK4
PK5 XADDR18
XADDR19
Voltage Reference
KWP2
KWP6
KWP0
KWP7
KWP1
KWP3
KWP4
KWP5
KWJ6
KWJ7
TIM
Signals shown in Bold are not available on n the 80-Pin Package
Module to
Port Routing
2K Byte EEPROM
PWM
MISO
MOSI
SCK
SS
SPI1
MISO
MOSI
SCK
SS
SPI2
CAN4 RxCAN
TxCAN
OSC
Debugger
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
22 Freescale Semiconductor
1.2 Signal Description
The MC9S12KG128 is available in a 112-pin low profile quad flat pack (LQFP) and a 80-pin quad flat
pack (QFP). Most pins perform two or more functions, as described in Section 1.2.1, “Signal Properties
Summary”.Figure 1-3 and Figure 1-4 show the pin assignments for different packages.
Figure 1-3. Pin Assignments for 112 LQFP
VRH
VDDA
PAD15/AN15
PAD07/AN07
PAD14/AN14
PAD06/AN06
PAD13/AN13
PAD05/AN05
PAD12/AN12
PAD04/AN04
PAD11/AN11
PAD03/AN03
PAD10/AN10
PAD02/AN02
PAD09/AN09
PAD01/AN01
PAD08/AN08
PAD00/AN00
VSS2
VDD2
PA7/ADDR15/DATA15
PA6/ADDR14/DATA14
PA5/ADDR13/DATA13
PA4/ADDR12/DATA12
PA3/ADDR11/DATA11
PA2/ADDR10/DATA10
PA1/ADDR9/DATA9
PA0/ADDR8/DATA8
PP4/KWP4/PWM4/MISO2
PP5/KWP5/PWM5/MOSI2
PP6/KWP6/PWM6/SS2
PP7/KWP7/PWM7/SCK2
PK7/ECS
VDDX
VSSX
PM0/RXCAN0
PM1/TXCAN0
PM2/RXCAN0/MISO0
PM3/TXCAN0/SS0
PM4/RXCAN0/RXCAN4/MOSI0
PM5/TXCAN0/TXCAN4/SCK0
PJ6/KWJ6/RXCAN4/SDA
PJ7/KWJ7/TXCAN4/SCL
VREGEN
PS7/SS0
PS6/SCK0
PS5/MOSI0
PS4/MISO0
PS3/TXD1
PS2/RXD1
PS1/TXD0
PS0/RXD0
PM6/RXCAN4
PM7/TXCAN4
VSSA
VRL
SS1/PWM3/KWP3/PP3
SCK1/PWM2/KWP2/PP2
MOSI1/PWM1/KWP1/PP1
MISO1/PWM0/KWP0/PP0
XADDR17/PK3
XADDR16/PK2
XADDR15/PK1
XADDR14/PK0
IOC0/PT0
IOC1/PT1
IOC2/PT2
IOC3/PT3
VDD1
VSS1
IOC4/PT4
IOC5/PT5
IOC6/PT6
IOC7/PT7
XADDR19/PK5
XADDR18/PK4
KWJ1/PJ1
KWJ0/PJ0
MODC/TAGHI/BKGD
ADDR0/DATA0/PB0
ADDR1/DATA1/PB1
ADDR2/DATA2/PB2
ADDR3/DATA3/PB3
ADDR4/DATA4/PB4
ADDR5/DATA5/PB5
ADDR6/DATA6/PB6
ADDR7/DATA7/PB7
SS2/KWH7/PH7
SCK2/KWH6/PH6
MOSI2/KWH5/PH5
MISO2/KWH4/PH4
XCLKS/NOACC/PE7
MODB/IPIPE1/PE6
MODA/IPIPE0/PE5
ECLK/PE4
VSSR
VDDR
RESET
VDDPLL
XFC
VSSPLL
EXTAL
XTAL
TEST
SS1/KWH3/PH3
SCK1/KWH2/PH2
MOSI1/KWH1/PH1
MISO1/KWH0/PH0
LSTRB/TAGLO/PE3
R/W/PE2
IRQ/PE1
XIRQ/PE0
Signals shown in Bold are not available on the 80-pin package
MC9S12KG128
112LQFP
112
111
110
109
108
107
106
105
104
103
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 23
Figure 1-4. Pin Assignments for 80 QFP
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
VRH
VDDA
PAD07/AN07
PAD06/AN06
PAD05/AN05
PAD04/AN04
PAD03/AN03
PAD02/AN02
PAD01/AN01
PAD00/AN00
VSS2
VDD2
PA7/ADDR15/DATA15
PA6/ADDR14/DATA14
PA5/ADDR13/DATA13
PA4/ADDR12/DATA12
PA3/ADDR11/DATA11
PA2/ADDR10/DATA10
PA1/ADDR9/DATA9
PA0/ADDR8/DATA8
PP4/KWP4/PWM4/MISO2
PP5/KWP5/PWM5/MOSI2
PP7/KWP7/PWM7/SCK2
VDDX
VSSX
PM0/RXCAN0
PM1/TXCAN0
PM2/RXCAN0/MISO0
PM3/TXCAN0/SS0
PM4/RXCAN0/RXCAN4/MOSI
0
PM5/TXCAN0/TXCAN4/SCK0
PJ6/KWJ6/RXCAN4/SDA
PJ7/KWJ7/TXCAN4/SCL
VREGEN
PS3/TXD1
PS2/RXD1
PS1/TXD0
PS0/RXD0
VSSA
VRL
PWM3/KWP3/PP3
PWM2/KWP2/PP2
PWM1/KWP1/PP1
PWM0/KWP0/PP0
IOC0/PT0
IOC1/PT1
IOC2/PT2
IOC3/PT3
VDD1
VSS1
IOC4/PT4
IOC5/PT5
IOC6/PT6
IOC7/PT7
MODC/TAGHI/BKGD
ADDR0/DATA0/PB0
ADDR1/DATA1/PB1
ADDR2/DATA2/PB2
ADDR3/DATA3/PB3
ADDR4/DATA4/PB4
ADDR5/DATA5/PB5
ADDR6/DATA6/PB6
ADDR7/DATA7/PB7
XCLKS/NOACC/PE7
MODB/IPIPE1/PE6
MODA/IPIPE0/PE5
ECLK/PE4
VSSR
VDDR
RESET
VDDPLL
XFC
VSSPLL
EXTAL
XTAL
TEST
LSTRB/TAGLO/PE3
R/W/PE2
IRQ/PE1
XIRQ/PE0
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
MC9S12KG128
80 QFP
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
24 Freescale Semiconductor
1.2.1 Signal Properties Summary
Table 1-2 summarizes the pin functionality. Signals shown in bold are not available in the 80-pin package.
Table 1-3 summarizes the power and ground pins.
Table 1-2. Signal Properties (Sheet 1 of 3)
Pin Name
Function 1 Pin Name
Function 2 Pin Name
Function 3 Pin Name
Function 4 Powered
by
Internal Pull
Resistor Description
CTRL Reset
State
EXTAL VDDPLL NA NA Oscillator Pins
XTAL VDDPLL NA NA
RESET VDDR None None External Reset
TEST NA NA NA Test Input
VREGEN VDDX NA NA Voltage Regulator Enable Input
XFC VDDPLL NA NA PLL Loop Filter
BKGD TAGHI MODC VDDR Always Up Up Background Debug, Tag High,
Mode Input
PAD[15:8] AN[15:8] VDDA None None PortAD Input, Analog Inputsof
ATD
PAD[7:0] AN[7:0] VDDA None None Port AD Input, Analog Inputs of
ATD
PA[7:0] ADDR[15:8]/
DATA[15:8] VDDR PUCR Disabled Port A I/O, Multiplexed
Address/Data
PB[7:0] ADDR[7:0]/
DATA[7:0] VDDR PUCR Disabled Port B I/O, Multiplexed
Address/Data
PE7 NOACC XCLKS VDDR PUCR Up Port E I/O, Access, Clock Select
PE6 IPIPE1 MODB VDDR While RESET
pin is low:
Down
Port E I/O, Pipe Status, Mode
Input
PE5 IPIPE0 MODA VDDR While RESET
pin is low:
Down
Port E I/O, Pipe Status, Mode
Input
PE4 ECLK VDDR PUCR Up Port E I/O, Bus Clock Output
PE3 LSTRB TAGLO VDDR PUCR Up Port E I/O, Byte Strobe, Tag Low
PE2 R/W VDDR PUCR Up Port E I/O, R/W in expanded
modes
PE1 IRQ VDDR PUCR Up Port E Input, Maskable Interrupt
PE0 XIRQ VDDR PUCR Up Port E Input, Non Maskable
Interrupt
PH7 KWH7 SS2 VDDR PERH/
PPSH Disabled Port H I/O, Interrupt, SS of SPI2
PH6 KWH6 SCK2 VDDR PERH/
PPSH Disabled Port H I/O, Interrupt, SCK of
SPI2
PH5 KWH5 MOSI2 VDDR PERH/
PPSH Disabled Port H I/O, Interrupt, MOSI of
SPI2
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 25
PH4 KWH4 MISO2 VDDR PERH/
PPSH Disabled Port H I/O, Interrupt, MISO of
SPI2
PH3 KWH3 SS1 VDDR PERH/
PPSH Disabled Port H I/O, Interrupt, SS of SPI1
PH2 KWH2 SCK1 VDDR PERH/
PPSH Disabled Port H I/O, Interrupt, SCK of
SPI1
PH1 KWH1 MOSI1 VDDR PERH/
PPSH Disabled Port H I/O, Interrupt, MOSI of
SPI1
PH0 KWH0 MISO1 VDDR PERH/
PPSH Disabled Port H I/O, Interrupt, MISO of
SPI1
PJ7 KWJ7 TXCAN4 SCL VDDX PERJ/
PPSJ Up Port J I/O, Interrupt, TX of CAN4,
SCL of IIC
PJ6 KWJ6 RXCAN4 SDA VDDX PERJ/
PPSJ Up Port J I/O, Interrupt, RX of CAN4,
SDA of IIC
PJ[1:0] KWJ[1:0] VDDX PERJ/
PPSJ Up Port J I/O, Interrupts
PK7 ECS ROMCTL VDDX PUCR Up Port K I/O, Emulation Chip
Select,
ROM On Enable
PK[5:0] XADDR[19:14] VDDX PUCR Up Port K I/O, Extended
Addresses
PM7 TXCAN4 VDDX PERM/
PPSM Disabled Port M I/O, CAN4 TX
PM6 RXCAN4 VDDX PERM/
PPSM Disabled Port M I/O, CAN4 RX
PM5 TXCAN0 TXCAN4 SCK0 VDDX PERM/
PPSM Disabled Port M I/O, CAN0 TX, CAN4 TX,
SPI0 SCK
PM4 RXCAN0 RXCAN4 MOSI0 VDDX PERM/
PPSM Disabled Port M I/O, CAN0 RX, CAN4 RX,
SPI0 MOSI
PM3 TXCAN0 SS0 VDDX PERM/
PPSM Disabled Port M I/O, CAN0 TX, SPI0 SS
PM2 RXCAN0 MISO0 VDDX PERM/
PPSM Disabled Port M I/O, CAN0 RX, SPI0 MISO
PM1 TXCAN0 VDDX PERM/
PPSM Disabled Port M I/O, CAN0 TX
PM0 RXCAN0 VDDX PERM/
PPSM Disabled Port M I/O, CAN0 RX
PP7 KWP7 PWM7 SCK2 VDDX PERP/
PPSP Disabled Port P I/O, Interrupt, PWM
Channel 7,
SCK of SPI2
PP6 KWP6 PWM6 SS2 VDDX PERP/
PPSP Disabled Port P I/O, Interrupt, PWM
Channel 6, SPI2 SS
Table 1-2. Signal Properties (Sheet 2 of 3)
Pin Name
Function 1 Pin Name
Function 2 Pin Name
Function 3 Pin Name
Function 4 Powered
by
Internal Pull
Resistor Description
CTRL Reset
State
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
26 Freescale Semiconductor
PP5 KWP5 PWM5 MOSI2 VDDX PERP/
PPSP Disabled Port P I/O, Interrupt, PWM
Channel 5,
SPI2 MOSI
PP4 KWP4 PWM4 MISO2 VDDX PERP/
PPSP Disabled Port P I/O, Interrupt, PWM
Channel 4, SPI2 MISO
PP3 KWP3 PWM3 SS1 VDDX PERP/
PPSP Disabled Port P I/O, Interrupt, PWM
Channel 3, SPI1 SS
PP2 KWP2 PWM2 SCK1 VDDX PERP/
PPSP Disabled Port P I/O, Interrupt, PWM
Channel 2, SPI1 SCK
PP1 KWP1 PWM1 MOSI1 VDDX PERP/
PPSP Disabled Port P I/O, Interrupt, PWM
Channel 1, SPI1 MOSI
PP0 KWP0 PWM0 MISO1 VDDX PERP/
PPSP Disabled Port P I/O, Interrupt, PWM
Channel 0, SPI1 MISO
PS7 SS0 VDDX PERS/
PPSS Up Port S I/O, SPI0 SS
PS6 SCK0 VDDX PERS/
PPSS Up Port S I/O, SPI0 SCK
PS5 MOSI0 VDDX PERS/
PPSS Up Port S I/O, SPI0 MOSI
PS4 MISO0 VDDX PERS/
PPSS Up Port S I/O, SPI0 MISO
PS3 TXD1 VDDX PERS/
PPSS Up Port S I/O, SCI1TXD
PS2 RXD1 VDDX PERS/
PPSS Up Port S I/O, SCI1RXD
PS1 TXD0 VDDX PERS/
PPSS Up Port S I/O, SCI0 TXD
PS0 RXD0 VDDX PERS/
PPSS Up Port S I/O, SCI0 RXD
PT[7:0] IOC[7:0] VDDX Up or
Down Disabled Port T I/O, Timer channels
Table 1-2. Signal Properties (Sheet 3 of 3)
Pin Name
Function 1 Pin Name
Function 2 Pin Name
Function 3 Pin Name
Function 4 Powered
by
Internal Pull
Resistor Description
CTRL Reset
State
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 27
NOTE
All VSS pins must be connected together in the application. Because fast
signal transitions place high, short-duration current demands on the power
supply, use bypass capacitors with high-frequency characteristics and place
them as close to the MCU as possible. Bypass requirements depend on
MCU pin load.
1.2.2 Detailed Signal Descriptions
1.2.2.1 EXTAL, XTAL — Oscillator Pins
EXTAL and XTAL are the crystal driver and external clock pins. On reset all the device clocks are derived
from the EXTAL input frequency. XTAL is the crystal output.
1.2.2.2 RESET — External Reset Pin
An active low bidirectional control signal, it acts as an input to initialize the MCU to a known start-up state,
and an output when an internal MCU function causes a reset.
1.2.2.3 TEST — Test Pin
This input only pin is reserved for test.
NOTE
The TEST pin must be tied to VSS in all applications.
Table 1-3. Power and Ground
Mnemonic Nominal
Voltage Description
VDD1 VDD2 2.5 V Internal power and ground generated by internal regulator. These also allow an external
source to supply the core VDD/VSS voltages and bypass the internal voltage regulator.
VSS1
VSS2 0V
VDDR 3.3/5.0 V External power and ground, supply to pin drivers and internal voltage regulator.
VSSR 0 V
VDDX 3.3/5.0 V External power and ground, supply to pin drivers.
VSSX 0 V
VDDA 3.3/5.0 V Operating voltage and ground for the analog-to-digital converter and the reference for the
internal voltage regulator, allows the supply voltage to the A/D to be bypassed
independently.
VSSA 0 V
VRH 3.3/5.0 V Reference voltage high for the ATD converter.
VRL 0 V Reference voltage low for the ATD converter.
VDDPLL 2.5 V Provides operating voltage and ground for the Phased-Locked Loop. This allowsthe supply
voltage to the PLL to be bypassed independently. Internal power and ground generated by
internal regulator.
VSSPLL 0 V
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
28 Freescale Semiconductor
1.2.2.4 VREGEN — Voltage Regulator Enable Pin
This input only pin enables or disables the on-chip voltage regulator.
1.2.2.5 XFC — PLL Loop Filter Pin
PLL loop filter. Please ask your Freescale representative for the interactive application note to compute
PLL loop filter elements. Any current leakage on this pin must be avoided.
Figure 1-5. PLL Loop Filter Connections
1.2.2.6 BKGD / TAGHI / MODC — Background Debug, Tag High, and Mode Pin
The BKGD/TAGHI/MODC pin is used as a pseudo-open-drain pin for the background debug
communication. In MCU expanded modes of operation when instruction tagging is on, an input low on
this pin during the falling edge of E-clock tags the high half of the instruction word being read into the
instruction queue. It is used as a MCU operating mode select pin during reset. The state of this pin is
latched to the MODC bit at the rising edge of RESET.
1.2.2.7 PAD[15:0] / AN[15:0] — Port AD Input Pins
PAD15 - PAD0 are general purpose input pins and analog inputs of the analog to digital converter with 16
channels (ATD).
1.2.2.8 PA[7:0] / ADDR[15:8] / DATA[15:8] — Port A I/O Pins
PA7–PA0 are general purpose input or output pins. In MCU expanded modes of operation, these pins are
used for the multiplexed external address and data bus.
1.2.2.9 PB[7:0] / ADDR[7:0] / DATA[7:0] — Port B I/O Pins
PB7–PB0 are general purpose input or output pins. In MCU expanded modes of operation, these pins are
used for the multiplexed external address and data bus.
1.2.2.10 PE7 / NOACC / XCLKS — Port E I/O Pin 7
PE7 is a general purpose input or output pin. During MCU expanded modes of operation, the NOACC
signal, when enabled, is used to indicate that the current bus cycle is an unused or “free” cycle. This signal
will assert when the CPU is not using the bus.
MCU
XFC
R
CS
CP
VDDPLLVDDPLL
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 29
The XCLKS is an input signal which controls whether a crystal in combination with the internal Loop
Controlled Pierce (low power) oscillator is used or whether Full Swing Pierce oscillator/external clock
circuitry is used. The state of this pin is latched at the rising edge of RESET. If the input is a logic low the
EXTAL pin is configured for an external clock drive or Full Swing Pierce Oscillator. If input is a logic high
a Loop Controlled Pierce oscillator circuit is configured on EXTAL and XTAL. Since this pin is an input
with a pull-up device during reset, if the pin is left floating, the default configuration is a Loop Controlled
Pierce oscillator circuit on EXTAL and XTAL.
Figure 1-6. Loop Controlled Pierce Oscillator Connections (PE7 = 1)
Figure 1-7. Full Swing Pierce Oscillator Connections (PE7 = 0)
Table 1-4. Clock Selection Based on PE7 During Reset
PE7 Description
1 Loop Controlled Pierce Oscillator selected
0 Full Swing Pierce Oscillator or external clock selected
MCU
EXTAL
XTAL
VSSPLL
CRYSTAL OR
CERAMIC
C8
C7
RESONATOR
* Rs can be zero (shorted) when use with higher frequency crystals.
Refer to manufacturer’s data.
MCU
EXTAL
XTAL RS*
RB
VSSPLL
C8
C7
CRYSTAL OR
CERAMIC
RESONATOR
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
30 Freescale Semiconductor
Figure 1-8. External Clock Connections (PE7 = 0)
1.2.2.11 PE6 / MODB / IPIPE1 — Port E I/O Pin 6
PE6 is a general purpose input or output pin. It is used as a MCU operating mode select pin during reset.
The state of this pin is latched to the MODB bit at the rising edge of RESET. This pin is shared with the
instruction queue tracking signal IPIPE1.
1.2.2.12 PE5 / MODA / IPIPE0 — Port E I/O Pin 5
PE5 is a general purpose input or output pin. It is used as a MCU operating mode select pin during reset.
The state of this pin is latched to the MODA bit at the rising edge of RESET. This pin is shared with the
instruction queue tracking signal IPIPE0.
1.2.2.13 PE4 / ECLK — Port E I/O Pin 4
PE4 is a general purpose input or output pin. It can be configured to drive the internal bus clock ECLK.
ECLK can be used as a timing reference.
1.2.2.14 PE3 / LSTRB / TAGLO — Port E I/O Pin 3
PE3 is a general purpose input or output pin. In MCU expanded modes of operation, LSTRB can be used
for the low-byte strobe function to indicate the type of bus access and when instruction tagging is on,
TAGLO is used to tag the low half of the instruction word being read into the instruction queue.
1.2.2.15 PE2 / R/W Port E I/O Pin 2
PE2 is a general purpose input or output pin. In MCU expanded modes of operations, this pin drives the
read/write output signal for the external bus. It indicates the direction of data on the external bus.
1.2.2.16 PE1 / IRQ — Port E Input Pin 1
PE1 is a general purpose input pin and the maskable interrupt request input that provides a means of
applying asynchronous interrupt requests. This will wake up the MCU from STOP or WAIT mode.
MCU
EXTAL
XTAL
CMOS-COMPATIBLE
EXTERNAL OSCILLATOR
NOT CONNECTED
(VDDPLL-LEVEL)
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 31
1.2.2.17 PE0 / XIRQ — Port E Input Pin 0
PE0 is a general purpose input pin and the non-maskable interrupt request input that provides a means of
applying asynchronous interrupt requests. This will wake up the MCU from STOP or WAIT mode.
1.2.2.18 PH7 / KWH7 / SS2 — Port H I/O Pin 7
PH7 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU
to exit STOP or WAIT mode. It can be configured as slave select pin SS of the Serial Peripheral Interface 2
(SPI2).
1.2.2.19 PH6 / KWH6 / SCK2 — Port H I/O Pin 6
PH6 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU
to exit STOP or WAIT mode. It can be configured as serial clock pin SCK of the Serial Peripheral
Interface 2 (SPI2).
1.2.2.20 PH5 / KWH5 / MOSI2 — Port H I/O Pin 5
PH5 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU
to exit STOP or WAIT mode. It can be configured as master output (during master mode) or slave input
pin (during slave mode) MOSI of the Serial Peripheral Interface 2 (SPI2).
1.2.2.21 PH4 / KWH4 / MISO2 — Port H I/O Pin 2
PH4 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU
to exit STOP or WAIT mode. It can be configured as master input (during master mode) or slave output
(during slave mode) pin MISO of the Serial Peripheral Interface 2 (SPI2).
1.2.2.22 PH3 / KWH3 / SS1 — Port H I/O Pin 3
PH3 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU
to exit STOP or WAIT mode. It can be configured as slave select pin SS of the Serial Peripheral Interface 1
(SPI1).
1.2.2.23 PH2 / KWH2 / SCK1 — Port H I/O Pin 2
PH2 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU
to exit STOP or WAIT mode. It can be configured as serial clock pin SCK of the Serial Peripheral
Interface 1 (SPI1).
1.2.2.24 PH1 / KWH1 / MOSI1 — Port H I/O Pin 1
PH1 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU
to exit STOP or WAIT mode. It can be configured as master output (during master mode) or slave input
pin (during slave mode) MOSI of the Serial Peripheral Interface 1 (SPI1).
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
32 Freescale Semiconductor
1.2.2.25 PH0 / KWH0 / MISO1 — Port H I/O Pin 0
PH0 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU
to exit STOP or WAIT mode. It can be configured as master input (during master mode) or slave output
(during slave mode) pin MISO of the Serial Peripheral Interface 1 (SPI1).
1.2.2.26 PJ7 / KWJ7 / TXCAN4 / SCL — PORT J I/O Pin 7
PJ7 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU
to exit STOP or WAIT mode. It can be configured as the transmit pin TXCAN for the Scalable Controller
Area Network controller 4 (CAN4) or the serial clock pin SCL of the IIC module.
1.2.2.27 PJ6 / KWJ6 / RXCAN4 / SDA — PORT J I/O Pin 6
PJ6 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU
to exit STOP or WAIT mode. It can be configured as the receive pin RXCAN for the Scalable Controller
Area Network controller 4 (CAN4) or the serial data pin SDA of the IIC module.
1.2.2.28 PJ[1:0] / KWJ[1:0] — Port J I/O Pins [1:0]
PJ1 and PJ0 are general purpose input or output pins. They can be configured to generate an interrupt
causing the MCU to exit STOP or WAIT mode.
1.2.2.29 PK7 / ECS / ROMCTL — Port K I/O Pin 7
PK7 is a general purpose input or output pin. During MCU expanded modes of operation, this pin is used
as the emulation chip select output (ECS). During MCU expanded modes of operation, this pin is used to
enable the Flash EEPROM memory in the memory map (ROMCTL). At the rising edge of RESET, the
state of this pin is latched to the ROMON bit.
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 33
For all other modes the reset state of the ROMON bit is as follows:
Special single: ROMCTL = 1
Normal single: ROMCTL = 1
Emulation expanded wide: ROMCTL = 0
Emulation expanded narrow: ROMCTL = 0
Special test: ROMCTL = 0
Peripheral test: ROMCTL = 1
1.2.2.30 PK[5:0] / XADDR[19:14] — Port K I/O Pins [5:0]
PK5-PK0 are general purpose input or output pins. In MCU expanded modes of operation, these pins
provide the expanded address XADDR[19:14] for the external bus.
1.2.2.31 PM7 / TXCAN4 — Port M I/O Pin 7
PM7 is a general purpose input or output pin. It can be configured as the transmit pin TXCAN of the
Scalable Controller Area Network controllers 4 (CAN4).
1.2.2.32 PM6 / RXCAN4 — Port M I/O Pin 6
PM6 is a general purpose input or output pin. It can be configured as the receive pin RXCAN of the
Scalable Controller Area Network controllers 4 (CAN4).
1.2.2.33 PM5 / TXCAN0 / TXCAN4 / SCK0 — Port M I/O Pin 5
PM5 is a general purpose input or output pin. It can be configured as the transmit pin TXCAN of the
Scalable Controller Area Network controllers 0 or 4 (CAN0 or CAN4). It can be configured as the serial
clock pin SCK of the Serial Peripheral Interface 0 (SPI0).
1.2.2.34 PM4 / RXCAN0 / RXCAN4/ MOSI0 — Port M I/O Pin 4
PM4 is a general purpose input or output pin. It can be configured as the receive pin RXCAN of the
Scalable Controller Area Network controllers 0 or 4 (CAN0 or CAN4). It can be configured as the master
output (during master mode) or slave input pin (during slave mode) MOSI for the Serial Peripheral
Interface 0 (SPI0).
1.2.2.35 PM3 / TXCAN0 / SS0 — Port M I/O Pin 3
PM3 is a general purpose input or output pin. It can be configured as the transmit pin TXCAN of the
Scalable Controller Area Network controller 0 (CAN0). It can be configured as the slave select pin SS of
the Serial Peripheral Interface 0 (SPI0).
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
34 Freescale Semiconductor
1.2.2.36 PM2 / RXCAN0 / MISO0 — Port M I/O Pin 2
PM2 is a general purpose input or output pin. It can be configured as the receive pin RXCAN of the
Scalable Controller Area Network controller 0 ( CAN0). It can be configured as the master input (during
master mode) or slave output pin (during slave mode) MISO for the Serial Peripheral Interface 0 (SPI0).
1.2.2.37 PM1 / TXCAN0 — Port M I/O Pin 1
PM1 is a general purpose input or output pin. It can be configured as the transmit pin TXCAN of the
Scalable Controller Area Network controller 0 (CAN0).
1.2.2.38 PM0 / RXCAN0 — Port M I/O Pin 0
PM0 is a general purpose input or output pin. It can be configured as the receive pin RXCAN of the
Scalable Controller Area Network controller 0 (CAN0).
1.2.2.39 PP7 / KWP7 / PWM7 / SCK2 — Port P I/O Pin 7
PP7 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU
to exit STOP or WAIT mode. It can be configured as Pulse Width Modulator (PWM) channel 7 output. It
can be configured as serial clock pin SCK of the Serial Peripheral Interface 2 (SPI2).
1.2.2.40 PP6 / KWP6 / PWM6 / SS2 — Port P I/O Pin 6
PP6 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU
to exit STOP or WAIT mode. It can be configured as Pulse Width Modulator (PWM) channel 6 output. It
can be configured as slave select pin SS of the Serial Peripheral Interface 2 (SPI2).
1.2.2.41 PP5 / KWP5 / PWM5 / MOSI2 — Port P I/O Pin 5
PP5 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU
to exit STOP or WAIT mode. It can be configured as Pulse Width Modulator (PWM) channel 5 output. It
can be configured as master output (during master mode) or slave input pin (during slave mode) MOSI of
the Serial Peripheral Interface 2 (SPI2).
1.2.2.42 PP4 / KWP4 / PWM4 / MISO2 — Port P I/O Pin 4
PP4 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU
to exit STOP or WAIT mode. It can be configured as Pulse Width Modulator (PWM) channel 4 output. It
can be configured as master input (during master mode) or slave output (during slave mode) pin MISO of
the Serial Peripheral Interface 2 (SPI2).
1.2.2.43 PP3 / KWP3 / PWM3 / SS1 — Port P I/O Pin 3
PP3 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU
to exit STOP or WAIT mode. It can be configured as Pulse Width Modulator (PWM) channel 3 output. It
can be configured as slave select pin SS of the Serial Peripheral Interface 1 (SPI1).
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 35
1.2.2.44 PP2 / KWP2 / PWM2 / SCK1 — Port P I/O Pin 2
PP2 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU
to exit STOP or WAIT mode. It can be configured as Pulse Width Modulator (PWM) channel 2 output. It
can be configured as serial clock pin SCK of the Serial Peripheral Interface 1 (SPI1).
1.2.2.45 PP1 / KWP1 / PWM1 / MOSI1 — Port P I/O Pin 1
PP1 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU
to exit STOP or WAIT mode. It can be configured as Pulse Width Modulator (PWM) channel 1 output. It
can be configured as master output (during master mode) or slave input pin (during slave mode) MOSI of
the Serial Peripheral Interface 1 (SPI1).
1.2.2.46 PP0 / KWP0 / PWM0 / MISO1 — Port P I/O Pin 0
PP0 is a general purpose input or output pin. It can be configured to generate an interrupt causing the MCU
to exit STOP or WAIT mode. It can be configured as Pulse Width Modulator (PWM) channel 0 output. It
can be configured as master input (during master mode) or slave output (during slave mode) pin MISO of
the Serial Peripheral Interface 1 (SPI1).
1.2.2.47 PS7 / SS0 — Port S I/O Pin 7
PS6 is a general purpose input or output pin. It can be configured as the slave select pin SS of the Serial
Peripheral Interface 0 (SPI0).
1.2.2.48 PS6 / SCK0 — Port S I/O Pin 6
PS6 is a general purpose input or output pin. It can be configured as the serial clock pin SCK of the Serial
Peripheral Interface 0 (SPI0).
1.2.2.49 PS5 / MOSI0 — Port S I/O Pin 5
PS5 is a general purpose input or output pin. It can be configured as master output (during master mode)
or slave input pin (during slave mode) MOSI of the Serial Peripheral Interface 0 (SPI0).
1.2.2.50 PS4 / MISO0 — Port S I/O Pin 4
PS4 is a general purpose input or output pin. It can be configured as master input (during master mode) or
slave output pin (during slave mode) MOSI of the Serial Peripheral Interface 0 (SPI0).
1.2.2.51 PS3 / TXD1 — Port S I/O Pin 3
PS3 is a general purpose input or output pin. It can be configured as the transmit pin TXD of Serial
Communication Interface 1 (SCI1).
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
36 Freescale Semiconductor
1.2.2.52 PS2 / RXD1 — Port S I/O Pin 2
PS2 is a general purpose input or output pin. It can be configured as the receive pin RXD of Serial
Communication Interface 1 (SCI1).
1.2.2.53 PS1 / TXD0 — Port S I/O Pin 1
PS1 is a general purpose input or output pin. It can be configured as the transmit pin TXD of Serial
Communication Interface 0 (SCI0).
1.2.2.54 PS0 / RXD0 — Port S I/O Pin 0
PS0 is a general purpose input or output pin. It can be configured as the receive pin RXD of Serial
Communication Interface 0 (SCI0).
1.2.2.55 PT[7:0] / IOC[7:0] — Port T I/O Pins [7:0]
PT7-PT0 are general purpose input or output pins. They can be configured as input capture or output
compare pins IOC7-IOC0 of the Timer (TIM).
1.2.3 Power Supply Pins
MC9S12KG128 power and ground pins are described below.
NOTE
All VSS pins must be connected together in the application.
1.2.3.1 VDDX,VSSX — Power Supply Pins for I/O Drivers
External power and ground for I/O drivers. Because fast signal transitions place high, short-duration
current demands on the power supply, use bypass capacitors with high-frequency characteristics and place
them as close to the MCU as possible. Bypass requirements depend on how heavily the MCU pins are
loaded.
1.2.3.2 VDDR, VSSR Power Supply Pins for I/O Drivers & for Internal Voltage
Regulator
External power and ground for I/O drivers and input to the internal voltage regulator. Because fast signal
transitions place high, short-duration current demands on the power supply, use bypass capacitors with
high-frequency characteristics and place them as close to the MCU as possible. Bypass requirements
depend on how heavily the MCU pins are loaded.
1.2.3.3 VDD1, VDD2, VSS1, VSS2 — Power Supply Pins for Internal Logic
Power is supplied to the MCU through VDD and VSS. Because fast signal transitions place high,
short-duration current demands on the power supply, use bypass capacitors with high-frequency
characteristics and place them as close to the MCU as possible. This 2.5V supply is derived from the
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 37
internal voltage regulator. There is no static load on those pins allowed. The internal voltage regulator is
turned off, if VREGEN is tied to ground.
NOTE
No load allowed except for bypass capacitors.
1.2.3.4 VDDA, VSSA — Power Supply Pins for ATD and VREG
VDDA, VSSA are the power supply and ground input pins for the voltage regulator and the analog to
digital converter. It also provides the reference for the internal voltage regulator. This allows the supply
voltage to the ATD and the reference voltage to be bypassed independently.
1.2.3.5 VRH, VRL — ATD Reference Voltage Input Pins
VRH and VRL are the reference voltage input pins for the analog to digital converter.
1.2.3.6 VDDPLL, VSSPLL — Power Supply Pins for PLL
Provides operating voltage and ground for the Oscillator and the Phased-Locked Loop. This allows the
supply voltage to the Oscillator and PLL to be bypassed independently. This 2.5V voltage is generated by
the internal voltage regulator.
NOTE
No load allowed except for bypass capacitors.
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
38 Freescale Semiconductor
1.3 Memory Map and Register Definition
1.3.1 Device Memory Map
Table 1-5 shows the device register map of the MC9S12KG128 after reset.
Table 1-5. MC9S12KT256 Device Memory Map
Address Module Size
0x0000–0x0017 CORE (Ports A, B, E, Modes, Inits, Test) 24
0x0018 Reserved 1
0x0019 Voltage Regulator (VREG) 1
0x001A–0x001B Device ID register (PARTID) 2
0x001C–0x001F CORE (MEMSIZ, IRQ, HPRIO) 4
0x0020–0x002F CORE (DBG) 16
0x0030–0x0033 CORE (PPAGE, Port K) 4
0x0034–0x003F Clock and Reset Generator (PLL, RTI, COP) 12
0x0040–0x006F Standard Timer 16-bit 8 channels (TIM) 48
0x0070–0x007F Reserved 16
0x0080–0x00AF Analog to Digital Converter 10-bit 16 channels (ATD) 48
0x00B0–0x00C7 Reserved 24
0x00C8–0x00CF Serial Communications Interface 0 (SCI0) 8
0x00D0–0x00D7 Serial Communications Interface 1 (SCI1) 8
0x00D8–0x00DF Serial Peripheral Interface 0 (SPI0) 8
0x00E0–0x00E7 Inter Integrated Circuit Bus (IIC) 8
0x00E8–0x00EF Reserved 8
0x00F0–0x00F7 Serial Peripheral Interface 1 (SPI1) 8
0x00F8–0x00FF Serial Peripheral Interface 2 (SPI2) 8
0x0100–0x010F Flash Control Register 16
0x0110- 0x011B EEPROM Control Register 12
0x011C–0x013F Reserved 36
0x0140–0x017F Scalable Controller Area Network 0 (CAN0) 64
0x0180–0x023F Reserved 192
0x0240–0x027F Port Integration Module (PIM) 64
0x0280–0x02BF Scalable Controller Area Network 4 (CAN4) 64
0x02C0–0x02E7 Pulse Width Modulator 8-bit 8 channels (PWM) 40
0x02E8–0x03FF Reserved 280
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 39
Figure 1-9 illustrates the full user configurable device memory map of MC9S12KG128.
Figure 1-9. MC9S12KG128 Memory Map
The figure shows a useful map, which is not the map out of reset. After reset the map is:
0x0000–0x03FF: Register Space
0x0000–0x1FFF: 8K RAM (1K RAM hidden behind Register Space)
0x0000–0x07FF: 2K EEPROM (not visible)
0x0000
0
xFFFF
0
xC000
0x8000
0x4000
0x0400
0x0800
0x1000
0x2000
0xFF00
EXT
NORMAL
SINGLE CHIP EXPANDED SPECIAL
SINGLE CHIP
VECTORSVECTORS VECTORS
0xFF00
0xFFFF BDM
(If Active)
0xC000
0xFFFF
16K Fixed Flash EEPROM
2K, 4K, 8K or 16K Protected Boot Sector
0x8000
0xBFFF
16K Page Window
eight * 16K Flash EEPROM Pages
0x4000
0x7FFF 16K Fixed Flash EEPROM
0.5K, 1K, 2K or 4K Protected Sector
0x2000
0x3FFF
8K Bytes RAM
Mappable to any 8K Boundary
0x0800
0x0FFF
2K Bytes EEPROM
Mappable to any 2K Boundary
0x0000
0x03FF
1K Register Space
Mappable to any 2K Boundary
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
40 Freescale Semiconductor
Figure 1-10 illustrates the full user configurable device memory map of MC9S12KL64 and
MC9S12KC64.
Figure 1-10. MC9S12KL(C)64 Memory Map
The figure shows a useful map, which is not the map out of reset. After reset the map is:
0x0000–0x03FF: Register Space
0x0000–0x0FFF: 4K RAM (1K RAM hidden behind Register Space)
0x0000–0x03FF: 1K EEPROM (not visible)
0x0000
0
xFFFF
0
xC000
0x8000
0x4000
0x0400
0x0800
0x1000
0x3000
0xFF00
EXT
NORMAL
SINGLE CHIP EXPANDED SPECIAL
SINGLE CHIP
VECTORSVECTORS VECTORS
0xFF00
0xFFFF BDM
(If Active)
0xC000
0xFFFF
16K Fixed Flash EEPROM
2K, 4K, 8K or 16K Protected Boot Sector
0x8000
0xBFFF
16K Page Window
four * 16K Flash EEPROM Pages
0x4000
0x7FFF 16K Fixed Flash EEPROM
0.5K, 1K, 2K or 4K Protected Sector
0x3000
0x3FFF
4K Bytes RAM
Mappable to any 4K Boundary
0x0800
0x0FFF
1K Bytes EEPROM
Mappable to any 2K Boundary
0x0000
0x03FF
1K Register Space
Mappable to any 2K Boundary
(1K mapped two times in 2K space)
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 41
Figure 1-11 illustrates the full user configurable device memory map of MC9S12KL32.
Figure 1-11. MC9S12KL32 Memory Map
The figure shows a useful map, which is not the map out of reset. After reset the map is:
0x0000–0x03FF: Register Space
0x0000–0x07FF: 2K RAM (1K RAM hidden behind Register Space)
0x0000–0x03FF: 1K EEPROM (not visible)
0x0000
0
xFFFF
0x8000
0x4000
0x0400
0x0800
0x1000
0x3800
0xFF00
EXT
NORMAL
SINGLE CHIP EXPANDED SPECIAL
SINGLE CHIP
VECTORSVECTORS VECTORS
0xFF00
0xFFFF BDM
(If Active)
0xFFFF
32K Fixed Flash EEPROM
2K, 4K, 8K or 16K Protected Boot Sector
0x8000
0x3800
0x3FFF
2K Bytes RAM
Mappable to any 2K Boundary
0x0800
0x0FFF
1K Bytes EEPROM
Mappable to any 2K Boundary
0x0000
0x03FF
1K Register Space
Mappable to any 2K Boundary
(1K mapped two times in 2K space)
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
42 Freescale Semiconductor
1.3.2 Detailed Register Map
The following tables show the detailed register map of the MC9S12KG128.
0x0000–0x000F MEBI Map 1 of 3 (HCS12 Multiplexed External Bus Interface)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0x0000 PORTA RBit 7 6 5 4 3 2 1 Bit 0
W
0x0001 PORTB RBit 7 6 5 4 3 2 1 Bit 0
W
0x0002 DDRA RBit 7 6 5 4 3 2 1 Bit 0
W
0x0003 DDRB RBit 7 6 5 4 3 2 1 Bit 0
W
0x0004 Reserved R00000000
W
0x0005 Reserved R00000000
W
0x0006 Reserved R00000000
W
0x0007 Reserved R00000000
W
0x0008 PORTE RBit 7 6 5 4 3 2 Bit 1 Bit 0
W
0x0009 DDRE RBit 7 6 5 4 3 Bit 2 00
W
0x000A PEAR RNOACCE 0PIPOE NECLK LSTRE RDWE 00
W
0x000B MODE RMODC MODB MODA 0IVIS 0EMK EME
W
0x000C PUCR RPUPKE 00
PUPEE 00
PUPBE PUPAE
W
0x000D RDRIV RRDPK 00
RDPE 00
RDPB RDPA
W
0x000E EBICTL R0000000
ESTR
W
0x000F Reserved R00000000
W
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 43
0x0010–0x0014 MMC Map 1 of 4 (HCS12 Module Mapping Control)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0x0010 INITRM RRAM15 RAM14 RAM13 RAM12 RAM11 00
RAMHAL
W
0x0011 INITRG R0 REG14 REG13 REG12 REG11 000
W
0x0012 INITEE REE15 EE14 EE13 EE12 EE11 00
EEON
W
0x0013 MISC R0 0 0 0 EXSTR1 EXSTR0 ROMHM ROMON
W
0x0014 Reserved R00000000
W
0x0015–0x0016 INT Map 1 of 2 (HCS12 Interrupt)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0x0015 ITCR R0 0 0 WRINT ADR3 ADR2 ADR1 ADR0
W
0x0016 ITEST RINTE INTC INTA INT8 INT6 INT4 INT2 INT0
W
0x0017–0x0017 MMC Map 2 of 4 (HCS12 Module Mapping Control)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0x0017 Reserved R00000000
W
0x0018–0x0018 Miscellaneous Peripherals (Device Guide)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0x0018 Reserved R00000000
W
0x0019–0x0019 VREG3V3 (Voltage Regulator)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0x0019 VREGCTRL R00000LVDS
LVIE LVIF
W
0x001A–0x001B Miscellaneous Peripherals (Device Guide)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0x001A PARTIDH R ID15 ID14 ID13 ID12 ID11 ID10 ID9 ID8
W
0x001B PARTIDL R ID7 ID6 ID5 ID4 ID3 ID2 ID1 ID0
W
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
44 Freescale Semiconductor
0x001C–0x001D MMC Map 3 of 4 (HCS12 Module Mapping Control, Device Guide)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0x001C MEMSIZ0 R reg_sw0 0 eep_sw1 eep_sw0 0 ram_sw2 ram_sw1 ram_sw0
W
0x001D MEMSIZ1 R rom_sw1 rom_sw0 0 0 0 0 pag_sw1 pag_sw0
W
0x001E–0x001E MEBI Map 2 of 3 (HCS12 Multiplexed External Bus Interface)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0x001E INTCR RIRQE IRQEN 000000
W
0x001F–0x001F INT Map 2 of 2 (HCS12 Interrupt)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0x001F HPRIO RPSEL7 PSEL6 PSEL5 PSEL4 PSEL3 PSEL2 PSEL1 0
W
0x0020–0x002F DBG Map 1 of 1 (HCS12 Debug)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0x0020 DBGC1 R DBGEN ARM TRGSEL BEGIN DBGBRK 0CAPMOD
—W
0x0021 DBGSC R AF BF CF 0 TRG
—W
0x0022 DBGTBH R Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8
—W
0x0023 DBGTBL R Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
—W
0x0024 DBGCNT R TBF 0 CNT
—W
0x0025 DBGCCX R PAGSEL EXTCMP
—W
0x0026 DBGCCH R Bit 15 14 13 12 11 10 9 Bit 8
—W
0x0027 DBGCCL R Bit 7 6 5 4 3 2 1 Bit 0
—W
0x0028 DBGC2 R BKABEN FULL BDM TAGAB BKCEN TAGC RWCEN RWC
BKPCT0 W
0x0029 DBGC3 R BKAMBH BKAMBL BKBMBH BKBMBL RWAEN RWA RWBEN RWB
BKPCT1 W
0x002A DBGCAX R PAGSEL EXTCMP
BKP0X W
0x002B DBGCAH R Bit 15 14 13 12 11 10 9 Bit 8
BKP0H W
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 45
0x002C DBGCAL R Bit 7 6 5 4 3 2 1 Bit 0
BKP0L W
0x002D DBGCBX R PAGSEL EXTCMP
BKP1X W
0x002E DBGCBH R Bit 15 14 13 12 11 10 9 Bit 8
BKP1H W
0x002F DBGCBL R Bit 7 6 5 4 3 2 1 Bit 0
BKP1L W
0x0030–0x0031 MMC Map 4 of 4 (HCS12 Module Mapping Control)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0x0030 PPAGE R0 0 PIX5 PIX4 PIX3 PIX2 PIX1 PIX0
W
0x0031 Reserved R00000000
W
0x0032–0x0033 MEBI Map 3 of 3 (HCS12 Multiplexed External Bus Interface)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0x0032 PORTK RBit 7 6 5 4 3 2 1 Bit 0
W
0x0033 DDRK RBit 7 6 5 4 3 2 1 Bit 0
W
0x0034–0x003F CRG (Clock and Reset Generator)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0x0034 SYNR R0 0 SYN5 SYN4 SYN3 SYN2 SYN1 SYN0
W
0x0035 REFDV R0 0 0 0 REFDV3 REFDV2 REFDV1 REFDV0
W
0x0036 CTFLG
TEST ONLY R TOUT7 TOUT6 TOUT5 TOUT4 TOUT3 TOUT2 TOUT1 TOUT0
W
0x0037 CRGFLG RRTIF PROF 0LOCKIF LOCK TRACK SCMIF SCM
W
0x0038 CRGINT RRTIE 00
LOCKIE 00
SCMIE 0
W
0x0039 CLKSEL RPLLSEL PSTP SYSWAI ROAWAI PLLWAI CWAI RTIWAI COPWAI
W
0x003A PLLCTL RCME PLLON AUTO ACQ 0PRE PCE SCME
W
0x003B RTICTL R0 RTR6 RTR5 RTR4 RTR3 RTR2 RTR1 RTR0
W
0x0020–0x002F DBG Map 1 of 1 (HCS12 Debug) (continued)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
46 Freescale Semiconductor
0x003C COPCTL RWCOP RSBCK 000
CR2 CR1 CR0
W
0x003D FORBYP
TEST ONLY RRTIBYP COPBYP 0PLLBYP 00
FCM 0
W
0x003E CTCTL
TEST ONLY R TCTL7 TCTL6 TCTL5 TCTL4 TCLT3 TCTL2 TCTL1 TCTL0
W
0x003F ARMCOP R00000000
W Bit 7 6 5 4 3 2 1 Bit 0
0x0040–0x006FTIM (Timer 16 Bit 8 Channels) (Sheet 1 of 3)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0x0040 TIOS RIOS7 IOS6 IOS5 IOS4 IOS3 IOS2 IOS1 IOS0
W
0x0041 CFORC R00000000
W FOC7 FOC6 FOC5 FOC4 FOC3 FOC2 FOC1 FOC0
0x0042 OC7M ROC7M7 OC7M6 OC7M5 OC7M4 OC7M3 OC7M2 OC7M1 OC7M0
W
0x0043 OC7D ROC7D7 OC7D6 OC7D5 OC7D4 OC7D3 OC7D2 OC7D1 OC7D0
W
0x0044 TCNT (hi) R Bit 15 14 13 12 11 10 9 Bit 8
W
0x0045 TCNT (lo) R Bit 7 6 5 4 3 2 1 Bit 0
W
0x0046 TSCR1 RTEN TSWAI TSFRZ TFFCA 0000
W
0x0047 TTOV RTOV7 TOV6 TOV5 TOV4 TOV3 TOV2 TOV1 TOV0
W
0x0048 TCTL1 ROM7 OL7 OM6 OL6 OM5 OL5 OM4 OL4
W
0x0049 TCTL2 ROM3 OL3 OM2 OL2 OM1 OL1 OM0 OL0
W
0x004A TCTL3 REDG7B EDG7A EDG6B EDG6A EDG5B EDG5A EDG4B EDG4A
W
0x004B TCTL4 REDG3B EDG3A EDG2B EDG2A EDG1B EDG1A EDG0B EDG0A
W
0x004C TIE RC7I C6I C5I C4I C3I C2I C1I C0I
W
0x004D TSCR2 RTOI 000
TCRE PR2 PR1 PR0
W
0x004E TFLG1 RC7F C6F C5F C4F C3F C2F C1F C0F
W
0x004F TFLG2 RTOF 0000000
W
0x0034–0x003F CRG (Clock and Reset Generator) (continued)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 47
0x0050 TC0 (hi) RBit 15 14 13 12 11 10 9 Bit 8
W
0x0051 TC0 (lo) RBit 7 6 5 4 3 2 1 Bit 0
W
0x0052 TC1 (hi) RBit 15 14 13 12 11 10 9 Bit 8
W
0x0053 TC1 (lo) RBit 7 6 5 4 3 2 1 Bit 0
W
0x0054 TC2 (hi) RBit 15 14 13 12 11 10 9 Bit 8
W
0x0055 TC2 (lo) RBit 7 6 5 4 3 2 1 Bit 0
W
0x0056 TC3 (hi) RBit 15 14 13 12 11 10 9 Bit 8
W
0x0057 TC3 (lo) RBit 7 6 5 4 3 2 1 Bit 0
W
0x0058 TC4 (hi) RBit 15 14 13 12 11 10 9 Bit 8
W
0x0059 TC4 (lo) RBit 7 6 5 4 3 2 1 Bit 0
W
0x005A TC5 (hi) RBit 15 14 13 12 11 10 9 Bit 8
W
0x005B TC5 (lo) RBit 7 6 5 4 3 2 1 Bit 0
W
0x005C TC6 (hi) RBit 15 14 13 12 11 10 9 Bit 8
W
0x005D TC6 (lo) RBit 7 6 5 4 3 2 1 Bit 0
W
0x005E TC7 (hi) RBit 15 14 13 12 11 10 9 Bit 8
W
0x005F TC7 (lo) RBit 7 6 5 4 3 2 1 Bit 0
W
0x0060 PACTL R0 PAEN PAMOD PEDGE CLK1 CLK0 PAOVI PAI
W
0x0061 PAFLG R000000
PAOVF PAIF
W
0x0062 PACNT (hi) RBit 7 6 5 4 3 2 1 Bit 0
W
0x0063 PACNT (lo) RBit 7 6 5 4 3 2 1 Bit 0
W
0x0064 Reserved R00000000
W
0x0065 Reserved R00000000
W
0x0066 Reserved R00000000
W
0x0040–0x006FTIM (Timer 16 Bit 8 Channels) (Sheet 2 of 3)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
48 Freescale Semiconductor
0x0067 Reserved R00000000
W
0x0068 Reserved R00000000
W
0x0069 Reserved R00000000
W
0x006A Reserved R00000000
W
0x006B Reserved R00000000
W
0x006C Reserved R00000000
W
0x006D Reserved R00000000
W
0x006E Reserved R00000000
W
0x006F Reserved R00000000
W
0x0070–0x007FReserved Space
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0x0070–
0x007F Reserved R00000000
W
0x0080–0x00AF ATD (Analog to Digital Converter 10 Bit 16 Channel)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0x0080 ATDCTL0 R0 0 0 0 WRAP3 WRAP2 WRAP1 WRAP0
W
0x0081 ATDCTL1 RETRIGSEL 000
ETRIGCH3 ETRIGCH2 ETRIGCH1 ETRIGCH0
W
0x0082 ATDCTL2 RADPU AFFC AWAI ETRIGLE ETRIGP ETRIG ASCIE ASCIF
W
0x0083 ATDCTL3 R0 S8C S4C S2C S1C FIFO FRZ1 FRZ0
W
0x0084 ATDCTL4 RSRES8 SMP1 SMP0 PRS4 PRS3 PRS2 PRS1 PRS0
W
0x0085 ATDCTL5 RDJM DSGN SCAN MULT 0CC CB CA
W
0x0086 ATDSTAT0 RSCF 0ETORF FIFOR 0 CC2 CC1 CC0
W
0x0087 Reserved R00000000
W
0x0040–0x006FTIM (Timer 16 Bit 8 Channels) (Sheet 3 of 3)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 49
0x0088 ATDTEST0 R00000000
W
0x0089 ATDTEST1 R0000000SC
W
0x008A ATDSTAT0 R CCF15 CCF14 CCF13 CCF12 CCF11 CCF10 CCF9 CCF8
W
0x008B ATDSTAT1 R CCF7 CCF6 CCF5 CCF4 CCF3 CCF2 CCF1 CCF0
W
0x008C ATDDIEN1 RIEN15 IEN14 IEN13 IEN12 IEN11 IEN10 IEN9 IEN8
W
0x008D ATDDIEN0 RIEN7 IEN6 IEN5 IEN4 IEN3 IEN2 IEN1 IEN0
W
0x008E PORTAD1 R PTAD15 PTAD14 PTAD13 PTAD12 PTAD11 PTAD10 PTAD9 PTAD8
W
0x008F PORTAD0 R PTAD7 PTAD6 PTAD5 PTAD4 PTAD3 PTAD2 PTAD1 PTAD0
W
0x0090 ATDDR0H R Bit 15 14 13 12 11 10 9 Bit 8
W
0x0091 ATDDR0L R Bit 7 Bit 6 0 0 0 0 0 0
W
0x0092 ATDDR1H R Bit 15 14 13 12 11 10 9 Bit 8
W
0x0093 ATDDR1L R Bit 7 Bit 6 0 0 0 0 0 0
W
0x0094 ATDDR2H R Bit 15 14 13 12 11 10 9 Bit 8
W
0x0095 ATDDR2L R Bit 7 Bit 6 0 0 0 0 0 0
W
0x0096 ATDDR3H R Bit 15 14 13 12 11 10 9 Bit 8
W
0x0097 ATDDR3L R Bit 7 Bit 6 0 0 0 0 0 0
W
0x0098 ATDDR4H R Bit 15 14 13 12 11 10 9 Bit 8
W
0x0099 ATDDR4L R Bit 7 Bit 6 0 0 0 0 0 0
W
0x009A ATDDR5H R Bit 15 14 13 12 11 10 9 Bit 8
W
0x009B ATDDR5L R Bit 7 Bit 6 0 0 0 0 0 0
W
0x009C ATDDR6H R Bit 15 14 13 12 11 10 9 Bit 8
W
0x009D ATDDR6L R Bit 7 Bit 6 0 0 0 0 0 0
W
0x009E ATDDR7H R Bit 15 14 13 12 11 10 9 Bit 8
W
0x0080–0x00AF ATD (Analog to Digital Converter 10 Bit 16 Channel) (continued)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
50 Freescale Semiconductor
0x009F ATDDR7L R Bit 7 Bit 6 0 0 0 0 0 0
W
0x00A0 ATDDR8H R Bit 15 14 13 12 11 10 9 Bit 8
W
0x00A1 ATDDR8L R Bit 7 Bit 6 0 0 0 0 0 0
W
0x00A2 ATDDR9H R Bit 15 14 13 12 11 10 9 Bit 8
W
0x00A3 ATDDR9L R Bit 7 Bit 6 0 0 0 0 0 0
W
0x00A4 ATDDR10H R Bit 15 14 13 12 11 10 9 Bit 8
W
0x00A5 ATDDR10L R Bit 7 Bit 6 0 0 0 0 0 0
W
0x00A6 ATDDR11H R Bit 15 14 13 12 11 10 9 Bit 8
W
0x00A7 ATDDR11L R Bit 7 Bit 6 0 0 0 0 0 0
W
0x00A8 ATDDR12H R Bit 15 14 13 12 11 10 9 Bit 8
W
0x00A9 ATDDR12L R Bit 7 Bit 6 0 0 0 0 0 0
W
0x00AA ATDDR13H R Bit 15 14 13 12 11 10 9 Bit 8
W
0x00AB ATDDR13L R Bit 7 Bit 6 0 0 0 0 0 0
W
0x00AC ATDDR14H R Bit 15 14 13 12 11 10 9 Bit 8
W
0x00AD ATDDR14L R Bit 7 Bit 6 0 0 0 0 0 0
W
0x00AE ATDDR15H R Bit 15 14 13 12 11 10 9 Bit 8
W
0x00AF ATDDR15L R Bit 7 Bit 6 0 0 0 0 0 0
W
0x00B0–0x00C7 Reserved space
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0x00B0–
0x00C7 Reserved R00000000
W
0x0080–0x00AF ATD (Analog to Digital Converter 10 Bit 16 Channel) (continued)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 51
0x00C8–0x00CF SCI0 (Asynchronous Serial Interface)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0x00C8 SCI0BDH R0 0 0 SBR12 SBR11 SBR10 SBR9 SBR8
W
0x00C9 SCI0BDL RSBR7 SBR6 SBR5 SBR4 SBR3 SBR2 SBR1 SBR0
W
0x00CA SCI0CR1 RLOOPS SCISWAI RSRC M WAKE ILT PE PT
W
0x00CB SCI0CR2 RTIE TCIE RIE ILIE TE RE RWU SBK
W
0x00CC SCI0SR1 R TDRE TC RDRF IDLE OR NF FE PF
W
0x00CD SCI0SR2 R00000
BRK13 TXDIR RAF
W
0x00CE SCI0DRH RR8 T8 000000
W
0x00CF SCI0DRL RR7R6R5R4R3R2R1R0
WT7T6T5T4T3T2T1T0
0x00D0–0x00D7 SCI1 (Asynchronous Serial Interface)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0x00D0 SCI1BDH R0 0 0 SBR12 SBR11 SBR10 SBR9 SBR8
W
0x00D1 SCI1BDL RSBR7 SBR6 SBR5 SBR4 SBR3 SBR2 SBR1 SBR0
W
0x00D2 SCI1CR1 RLOOPS SCISWAI RSRC M WAKE ILT PE PT
W
0x00D3 SCI1CR2 RTIE TCIE RIE ILIE TE RE RWU SBK
W
0x00D4 SCI1SR1 R TDRE TC RDRF IDLE OR NF FE PF
W
0x00D5 SCI1SR2 R00000
BRK13 TXDIR RAF
W
0x00D6 SCI1DRH RR8 T8 000000
W
0x00D7 SCI1DRL RR7R6R5R4R3R2R1R0
WT7T6T5T4T3T2T1T0
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
52 Freescale Semiconductor
0x00D8–0x00DF SPI0 (Serial Peripheral Interface)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0x00D8 SPI0CR1 RSPIE SPE SPTIE MSTR CPOL CPHA SSOE LSBFE
W
0x00D9 SPI0CR2 R0 0 0MODFEN BIDIROE 0SPISWAI SPC0
W
0x00DA SPI0BR R0 SPPR2 SPPR1 SPPR0 0SPR2 SPR1 SPR0
W
0x00DB SPI0SR R SPIF 0 SPTEF MODF 0 0 0 0
W
0x00DC Reserved R00000000
W
0x00DD SPI0DR RBit 7 6 5 4 3 2 1 Bit 0
W
0x00DE Reserved R00000000
W
0x00DF Reserved R00000000
W
0x00E0–0x00E7 IIC (Inter IC Bus)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0x00E0 IBAD RADR7 ADR6 ADR5 ADR4 ADR3 ADR2 ADR1 0
W
0x00E1 IBFD RIBC7 IBC6 IBC5 IBC4 IBC3 IBC2 IBC1 IBC0
W
0x00E2 IBCR RIBEN IBIE MS/SL TX/RX TXAK 00
IBSWAI
W RSTA
0x00E3 IBSR R TCF IAAS IBB IBAL 0SRW
IBIF RXAK
W
0x00E4 IBDR RD7 D6 D5 D4 D3 D2 D1 D 0
W
0x00E5 Reserved R0 0 00 0 0 00
W
0x00E6 Reserved R00000000
W
0x00E7 Reserved R00000000
W
0x00E8–0x00EF Reserved Space
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0x00E8–
0x00EF Reserved R00000000
W
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 53
0x00F0–0x00F7 SPI1 (Serial Peripheral Interface)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0x00F0 SPI1CR1 RSPIE SPE SPTIE MSTR CPOL CPHA SSOE LSBFE
W
0x00F1 SPI1CR2 R0 0 0MODFEN BIDIROE 0SPISWAI SPC0
W
0x00F2 SPI1BR R0 SPPR2 SPPR1 SPPR0 0SPR2 SPR1 SPR0
W
0x00F3 SPI1SR R SPIF 0 SPTEF MODF 0 0 0 0
W
0x00F4 Reserved R00000000
W
0x00F5 SPI1DR RBit 7 6 5 4 3 2 1 Bit 0
W
0x00F6 Reserved R00000000
W
0x00F7 Reserved R00000000
W
0x00F8–0x00FF SPI2 (Serial Peripheral Interface)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0x00F8 SPI2CR1 RSPIE SPE SPTIE MSTR CPOL CPHA SSOE LSBFE
W
0x00F9 SPI2CR2 R0 0 0MODFEN BIDIROE 0SPISWAI SPC0
W
0x00FA SPI2BR R0 SPPR2 SPPR1 SPPR0 0SPR2 SPR1 SPR0
W
0x00FB SPI2SR R SPIF 0 SPTEF MODF 0 0 0 0
W
0x00FC Reserved R00000000
W
0x00FD SPI2DR RBit 7 6 5 4 3 2 1 Bit 0
W
0x00FE Reserved R00000000
W
0x00FF Reserved R00000000
W
0x0100–0x010F Flash Control Register
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0x0100 FCLKDIV R FDIVLD PRDIV8 FDIV5 FDIV4 FDIV3 FDIV2 FDIV1 FDIV0
W
0x0101 FSEC R KEYEN RNV5 RNV4 RNV3 RNV2 SEC
W
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
54 Freescale Semiconductor
0x0102 FTSTMOD R0 0 0 0 FDFD 000
W
0x0103 FCNFG RCBEIE CCIE KEYACC 0DFDIE 000
W
0x0104 FPROT RFPOPEN RNV6 FPHDIS FPHS FPLDIS FPLS
W
0x0105 FSTAT RCBEIF CCIF PVIOL ACCERR DFDIF BLANK 0 0
W
0x0106 FCMD R0 CMDB
W
0x0107 Reserved R00000000
W
0x0108 FADDRHI R FADDRHI
W
0x0109 FADDRLO R FADDRLO
W
0x010A FDATAHI R FDATAHI
W
0x010B FDATALO R FDATALO
W
0x010C Reserved R00000000
W
0x010D Reserved R00000000
W
0x010E Reserved R00000000
W
0x010F Reserved R00000000
W
0x0110–0x011B EEPROM Control Register
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0x0110 ECLKDIV R EDIVLD PRDIV8 EDIV5 EDIV4 EDIV3 EDIV2 EDIV1 EDIV0
W
0x0111 Reserved R00000000
W
0x0112 Reserved for
Factory Test R00000000
W
0x0113 ECNFG RCBEIE CCIE 000000
W
0x0114 EPROT REPOPEN NV6 NV5 NV4 EPDIS EP2 EP1 EP0
W
0x0115 ESTAT RCBEIF CCIF PVIOL ACCERR 0BLANK 00
W
0x0100–0x010F Flash Control Register (continued)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 55
0x0116 ECMD R0 CMDB6 CMDB5 00
CMDB2 0CMDB0
W
0x0117 Reserved for
Factory Test R00000000
W
0x0118 EADDRHI R00000
10 9 Bit 8
W
0x0119 EADDRLO RBit 7 6 5 4 3 2 1 Bit 0
W
0x011A EDATAHI RBit 15 14 13 12 11 10 9 Bit 8
W
0x011B EDATALO RBit 7 6 5 4 3 2 1 Bit 0
W
0x011C–0x013F Reserved Space
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0x011C–
0x013F Reserved R00000000
W
0x0140–0x017F CAN0 (MSCAN)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0x0140 CAN0CTL0 RRXFRM RXACT CSWAI SYNCH TIME WUPE SLPRQ INITRQ
W
0x0141 CAN0CTL1 RCANE CLKSRC LOOPB LISTEN 0WUPM SLPAK INITAK
W
0x0142 CAN0BTR0 RSJW1 SJW0 BRP5 BRP4 BRP3 BRP2 BRP1 BRP0
W
0x0143 CAN0BTR1 RSAMP TSEG22 TSEG21 TSEG20 TSEG13 TSEG12 TSEG11 TSEG10
W
0x0144 CAN0RFLG RWUPIF CSCIF RSTAT1 RSTAT0 TSTAT1 TSTAT0 OVRIF RXF
W
0x0145 CAN0RIER RWUPIE CSCIE RSTATE1 RSTATE0 TSTATE1 TSTATE0 OVRIE RXFIE
W
0x0146 CAN0TFLG R00000
TXE2 TXE1 TXE0
W
0x0147 CAN0TIER R00000
TXEIE2 TXEIE1 TXEIE0
W
0x0148 CAN0TARQ R00000
ABTRQ2 ABTRQ1 ABTRQ0
W
0x0149 CAN0TAAK R 0 0 0 0 0 ABTAK2 ABTAK1 ABTAK0
W
0x014A CAN0TBSEL R00000
TX2 TX1 TX0
W
0x0110–0x011B EEPROM Control Register (continued)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
56 Freescale Semiconductor
0x014B CAN0IDAC R0 0 IDAM1 IDAM0 0 IDHIT2 IDHIT1 IDHIT0
W
0x014C Reserved R00000000
W
0x014D Reserved R00000000
W
0x014E CAN0RXERR R RXERR7 RXERR6 RXERR5 RXERR4 RXERR3 RXERR2 RXERR1 RXERR0
W
0x014F CAN0TXERR R TXERR7 TXERR6 TXERR5 TXERR4 TXERR3 TXERR2 TXERR1 TXERR0
W
0x0150–
0x0153 CAN0IDAR0–
CAN0IDAR3 RAC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0
W
0x0154–
0x0157 CAN0IDMR0–
CAN0IDMR3 RAM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0
W
0x0158–
0x015B CAN0IDAR4–
CAN0IDAR7 RAC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0
W
0x015C–
0x015F CAN0IDMR4–
CAN0IDMR7 RAM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0
W
0x0160–
0x016F CAN0RXFG R FOREGROUND RECEIVE BUFFER (see Table 1-6)
W
0x0170–
0x017F CAN0TXFG RFOREGROUND TRANSMIT BUFFER (see Table 1-6)
W
Table 1-6. Detailed MSCAN Foreground Receive and Transmit Buffer Layout
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0x00 Extended ID R ID28 ID27 ID26 ID25 ID24 ID23 ID22 ID21
Standard ID R ID10 ID9 ID8 ID7 ID6 ID5 ID4 ID3
CANxRIDR0 W
0x01 Extended ID R ID20 ID19 ID18 SRR=1 IDE=1 ID17 ID16 ID15
Standard ID R ID2 ID1 ID0 RTR IDE=0
CANxRIDR1 W
0x02 Extended ID R ID14 ID13 ID12 ID11 ID10 ID9 ID8 ID7
Standard ID R
CANxRIDR2 W
0x03 Extended ID R ID6 ID5 ID4 ID3 ID2 ID1 ID0 RTR
Standard ID R
CANxRIDR3 W
0x04–
0x0B CANxRDSR0–
CANxRDSR7 R DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
W
0x0C CANRxDLR RDLC3 DLC2 DLC1 DLC0
W
0x0D Reserved R
W
0x0E CANxRTSRH R TSR15 TSR14 TSR13 TSR12 TSR11 TSR10 TSR9 TSR8
W
0x0140–0x017F CAN0 (MSCAN)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 57
0x0F CANxRTSRL R TSR7 TSR6 TSR5 TSR4 TSR3 TSR2 TSR1 TSR0
W
0x10
Extended ID R ID28 ID27 ID26 ID25 ID24 ID23 ID22 ID21
CANxTIDR0 W
Standard ID R ID10 ID9 ID8 ID7 ID6 ID5 ID4 ID3
W
0x10
Extended ID R ID20 ID19 ID18 SRR=1 IDE=1 ID17 ID16 ID15
CANxTIDR1 W
Standard ID R ID2 ID1 ID0 RTR IDE=0
W
0x12
Extended ID R ID14 ID13 ID12 ID11 ID10 ID9 ID8 ID7
CANxTIDR2 W
Standard ID R
W
0x13
Extended ID R ID6 ID5 ID4 ID3 ID2 ID1 ID0 RTR
CANxTIDR3 W
Standard ID R
W
0x14–
0x1B CANxTDSR0–
CANxTDSR7 RDB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
W
0x1C CANxTDLR RDLC3 DLC2 DLC1 DLC0
W
0x1D CONxTTBPR RPRIO7 PRIO6 PRIO5 PRIO4 PRIO3 PRIO2 PRIO1 PRIO0
W
0x1E CANxTTSRH R TSR15 TSR14 TSR13 TSR12 TSR11 TSR10 TSR9 TSR8
W
0x1F CANxTTSRL R TSR7 TSR6 TSR5 TSR4 TSR3 TSR2 TSR1 TSR0
W
0x0180–0x023F Reserved Space
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0x0180–
0x023F Reserved R00000000
W
0x0240–0x027F PIM (Port Integration Module) (Sheet 1 of 3)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0x0240 PTT RPTT7 PTT6 PTT5 PTT4 PTT3 PTT2 PTT1 PTT0
W
0x0241 PTIT R PTIT7 PTIT6 PTIT5 PTIT4 PTIT3 PTIT2 PTIT1 PTIT0
W
0x0242 DDRT RDDRT7 DDRT7 DDRT5 DDRT4 DDRT3 DDRT2 DDRT1 DDRT0
W
Table 1-6. Detailed MSCAN Foreground Receive and Transmit Buffer Layout (continued)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
58 Freescale Semiconductor
0x0243 RDRT RRDRT7 RDRT6 RDRT5 RDRT4 RDRT3 RDRT2 RDRT1 RDRT0
W
0x0244 PERT RPERT7 PERT6 PERT5 PERT4 PERT3 PERT2 PERT1 PERT0
W
0x0245 PPST RPPST7 PPST6 PPST5 PPST4 PPST3 PPST2 PPST1 PPST0
W
0x0246 Reserved R00000000
W
0x0247 Reserved R00000000
W
0x0248 PTS RPTS7 PTS6 PTS5 PTS4 PTS3 PTS2 PTS1 PTS0
W
0x0249 PTIS R PTIS7 PTIS6 PTIS5 PTIS4 PTIS3 PTIS2 PTIS1 PTIS0
W
0x024A DDRS RDDRS7 DDRS7 DDRS5 DDRS4 DDRS3 DDRS2 DDRS1 DDRS0
W
0x024B RDRS RRDRS7 RDRS6 RDRS5 RDRS4 RDRS3 RDRS2 RDRS1 RDRS0
W
0x024C PERS RPERS7 PERS6 PERS5 PERS4 PERS3 PERS2 PERS1 PERS0
W
0x024D PPSS RPPSS7 PPSS6 PPSS5 PPSS4 PPSS3 PPSS2 PPSS1 PPSS0
W
0x024E WOMS RWOMS7 WOMS6 WOMS5 WOMS4 WOMS3 WOMS2 WOMS1 WOMS0
W
0x024F Reserved R00000000
W
0x0250 PTM RPTM7 PTM6 PTM5 PTM4 PTM3 PTM2 PTM1 PTM0
W
0x0251 PTIM R PTIM7 PTIM6 PTIM5 PTIM4 PTIM3 PTIM2 PTIM1 PTIM0
W
0x0252 DDRM RDDRM7 DDRM7 DDRM5 DDRM4 DDRM3 DDRM2 DDRM1 DDRM0
W
0x0253 RDRM RRDRM7 RDRM6 RDRM5 RDRM4 RDRM3 RDRM2 RDRM1 RDRM0
W
0x0254 PERM RPERM7 PERM6 PERM5 PERM4 PERM3 PERM2 PERM1 PERM0
W
0x0255 PPSM RPPSM7 PPSM6 PPSM5 PPSM4 PPSM3 PPSM2 PPSM1 PPSM0
W
0x0256 WOMM RWOMM7 WOMM6 WOMM5 WOMM4 WOMM3 WOMM2 WOMM1 WOMM0
W
0x0257 MODRR R0MODRR6 MODRR5 MODRR4 MODRR3 MODRR2 MODRR1 MODRR0
W
0x0258 PTP RPTP7 PTP6 PTP5 PTP4 PTP3 PTP2 PTP1 PTP0
W
0x0259 PTIP R PTIP7 PTIP6 PTIP5 PTIP4 PTIP3 PTIP2 PTIP1 PTIP0
W
0x0240–0x027F PIM (Port Integration Module) (Sheet 2 of 3)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 59
0x025A DDRP RDDRP7 DDRP7 DDRP5 DDRP4 DDRP3 DDRP2 DDRP1 DDRP0
W
0x025B RDRP RRDRP7 RDRP6 RDRP5 RDRP4 RDRP3 RDRP2 RDRP1 RDRP0
W
0x025C PERP RPERP7 PERP6 PERP5 PERP4 PERP3 PERP2 PERP1 PERP0
W
0x025D PPSP RPPSP7 PPSP6 PPSP5 PPSP4 PPSP3 PPSP2 PPSP1 PPSS0
W
0x025E PIEP RPIEP7 PIEP6 PIEP5 PIEP4 PIEP3 PIEP2 PIEP1 PIEP0
W
0x025F PIFP RPIFP7 PIFP6 PIFP5 PIFP4 PIFP3 PIFP2 PIFP1 PIFP0
W
0x0260 PTH RPTH7 PTH6 PTH5 PTH4 PTH3 PTH2 PTH1 PTH0
W
0x0261 PTIH R PTIH7 PTIH6 PTIH5 PTIH4 PTIH3 PTIH2 PTIH1 PTIH0
W
0x0262 DDRH RDDRH7 DDRH7 DDRH5 DDRH4 DDRH3 DDRH2 DDRH1 DDRH0
W
0x0263 RDRH RRDRH7 RDRH6 RDRH5 RDRH4 RDRH3 RDRH2 RDRH1 RDRH0
W
0x0264 PERH RPERH7 PERH6 PERH5 PERH4 PERH3 PERH2 PERH1 PERH0
W
0x0265 PPSH RPPSH7 PPSH6 PPSH5 PPSH4 PPSH3 PPSH2 PPSH1 PPSH0
W
0x0266 PIEH RPIEH7 PIEH6 PIEH5 PIEH4 PIEH3 PIEH2 PIEH1 PIEH0
W
0x0267 PIFH RPIFH7 PIFH6 PIFH5 PIFH4 PIFH3 PIFH2 PIFH1 PIFH0
W
0x0268 PTJ RPTJ7 PTJ6 0000
PTJ1 PTJ0
W
0x0269 PTIJ R PTIJ7 PTIJ6 0 0 0 0 PTIJ1 PTIJ0
W
0x026A DDRJ RDDRJ7 DDRJ7 0000
DDRJ1 DDRJ0
W
0x026B RDRJ RRDRJ7 RDRJ6 0000
RDRJ1 RDRJ0
W
0x026C PERJ RPERJ7 PERJ6 0000
PERJ1 PERJ0
W
0x026D PPSJ RPPSJ7 PPSJ6 0000
PPSJ1 PPSJ0
W
0x026E PIEJ RPIEJ7 PIEJ6 0000
PIEJ1 PIEJ0
W
0x026F PIFJ RPIFJ7 PIFJ6 0000
PIFJ1 PIFJ0
W
0x0270–
0x027F Reserved R
0x0240–0x027F PIM (Port Integration Module) (Sheet 3 of 3)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
60 Freescale Semiconductor
0x0280–0x02BF CAN4 (MSCAN)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0x0280 CAN4CTL0 RRXFRM RXACT CSWAI SYNCH TIME WUPE SLPRQ INITRQ
W
0x0281 CAN4CTL1 RCANE CLKSRC LOOPB LISTEN 0WUPM SLPAK INITAK
W
0x0282 CAN4BTR0 RSJW1 SJW0 BRP5 BRP4 BRP3 BRP2 BRP1 BRP0
W
0x0283 CAN4BTR1 RSAMP TSEG22 TSEG21 TSEG20 TSEG13 TSEG12 TSEG11 TSEG10
W
0x0284 CAN4RFLG RWUPIF CSCIF RSTAT1 RSTAT0 TSTAT1 TSTAT0 OVRIF RXF
W
0x0285 CAN4RIER RWUPIE CSCIE RSTATE1 RSTATE0 TSTATE1 TSTATE0 OVRIE RXFIE
W
0x0286 CAN4TFLG R00000
TXE2 TXE1 TXE0
W
0x0287 CAN4TIER R00000
TXEIE2 TXEIE1 TXEIE0
W
0x0288 CAN4TARQ R00000
ABTRQ2 ABTRQ1 ABTRQ0
W
0x0289 CAN4TAAK R 0 0 0 0 0 ABTAK2 ABTAK1 ABTAK0
W
0x028A CAN4TBSEL R00000
TX2 TX1 TX0
W
0x028B CAN4IDAC R0 0 IDAM1 IDAM0 0 IDHIT2 IDHIT1 IDHIT0
W
0x028C Reserved R00000000
W
0x028D Reserved R00000000
W
0x028E CAN4RXERR R RXERR7 RXERR6 RXERR5 RXERR4 RXERR3 RXERR2 RXERR1 RXERR0
W
0x028F CAN4TXERR R TXERR7 TXERR6 TXERR5 TXERR4 TXERR3 TXERR2 TXERR1 TXERR0
W
0x0290 CAN4IDAR0 RAC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0
W
0x0291 CAN4IDAR1 RAC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0
W
0x0292 CAN4IDAR2 RAC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0
W
0x0293 CAN4IDAR3 RAC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0
W
0x0294 CAN4IDMR0 RAM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0
W
0x0295 CAN4IDMR1 RAM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0
W
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 61
0x0296 CAN4IDMR2 RAM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0
W
0x0297 CAN4IDMR3 RAM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0
W
0x0298 CAN4IDAR4 RAC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0
W
0x0299 CAN4IDAR5 RAC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0
W
0x029A CAN4IDAR6 RAC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0
W
0x029B CAN4IDAR7 RAC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0
W
0x029C CAN4IDMR4 RAM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0
W
0x029D CAN4IDMR5 RAM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0
W
0x029E CAN4IDMR6 RAM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0
W
0x029F CAN4IDMR7 RAM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0
W
0x02A0–
0x02AF CAN4RXFG R FOREGROUND RECEIVE BUFFER (see Table 1-6)
W
0x02B0–
0x02BF CAN4TXFG RFOREGROUND TRANSMIT BUFFER (see Table 1-6)
W
0x02C0–0x02E7 PWM (Pulse Width Modulator 8 Bit 8 Channel)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0x02C0 PWME RPWME7 PWME6 PWME5 PWME4 PWME3 PWME2 PWME1 PWME0
W
0x02C1 PWMPOL RPPOL7 PPOL6 PPOL5 PPOL4 PPOL3 PPOL2 PPOL1 PPOL0
W
0x02C2 PWMCLK RPCLK7 PCLK6 PCLK5 PCLK4 PCLK3 PCLK2 PCLK1 PCLK0
W
0x02C3 PWMPRCLK R0 PCKB2 PCKB1 PCKB0 0PCKA2 PCKA1 PCKA0
W
0x02C4 PWMCAE RCAE7 CAE6 CAE5 CAE4 CAE3 CAE2 CAE1 CAE0
W
0x02C5 PWMCTL RCON67 CON45 CON23 CON01 PSWAI PFRZ 00
W
0x02C6 PWMTST
Test Only R00000000
W
0x02C7 PWMPRSC R00000000
W
0x0280–0x02BF CAN4 (MSCAN) (continued)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
62 Freescale Semiconductor
0x02C8 PWMSCLA RBit 7 6 5 4 3 2 1 Bit 0
W
0x02C9 PWMSCLB RBit 7 6 5 4 3 2 1 Bit 0
W
0x02CA PWMSCNTA R00000000
W
0x02CB PWMSCNTB R00000000
W
0x02CC PWMCNT0 R Bit 7 6 5 4 3 2 1 Bit 0
W00000000
0x02CD PWMCNT1 R Bit 7 6 5 4 3 2 1 Bit 0
W00000000
0x02CE PWMCNT2 R Bit 7 6 5 4 3 2 1 Bit 0
W00000000
0x02CF PWMCNT3 R Bit 7 6 5 4 3 2 1 Bit 0
W00000000
0x02D0 PWMCNT4 R Bit 7 6 5 4 3 2 1 Bit 0
W00000000
0x02D1 PWMCNT5 R Bit 7 6 5 4 3 2 1 Bit 0
W00000000
0x02D2 PWMCNT6 R Bit 7 6 5 4 3 2 1 Bit 0
W00000000
0x02D3 PWMCNT7 R Bit 7 6 5 4 3 2 1 Bit 0
W00000000
0x02D4 PWMPER0 RBit 7 6 5 4 3 2 1 Bit 0
W
0x02D5 PWMPER1 RBit 7 6 5 4 3 2 1 Bit 0
W
0x02D6 PWMPER2 RBit 7 6 5 4 3 2 1 Bit 0
W
0x02D7 PWMPER3 RBit 7 6 5 4 3 2 1 Bit 0
W
0x02D8 PWMPER4 RBit 7 6 5 4 3 2 1 Bit 0
W
0x02D9 PWMPER5 RBit 7 6 5 4 3 2 1 Bit 0
W
0x02DA PWMPER6 RBit 7 6 5 4 3 2 1 Bit 0
W
0x02DB PWMPER7 RBit 7 6 5 4 3 2 1 Bit 0
W
0x02DC PWMDTY0 RBit 7 6 5 4 3 2 1 Bit 0
W
0x02DD PWMDTY1 RBit 7 6 5 4 3 2 1 Bit 0
W
0x02DE PWMDTY2 RBit 7 6 5 4 3 2 1 Bit 0
W
0x02C0–0x02E7 PWM (Pulse Width Modulator 8 Bit 8 Channel) (continued)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 63
0x02DF PWMDTY3 RBit 7 6 5 4 3 2 1 Bit 0
W
0x02E0 PWMDTY4 RBit 7 6 5 4 3 2 1 Bit 0
W
0x02E1 PWMDTY5 RBit 7 6 5 4 3 2 1 Bit 0
W
0x02E2 PWMDTY6 RBit 7 6 5 4 3 2 1 Bit 0
W
0x02E3 PWMDTY7 RBit 7 6 5 4 3 2 1 Bit 0
W
0x02E4 PWMSDN RPWMIF PWMIE PWMRSTRT PWMLVL 0PWM7IN PWM7INL PWM7ENA
W
0x02E5 Reserved R00000000
W
0x02E6 Reserved R00000000
W
0x02E7 Reserved R00000000
W
0x02E8–0x03FF Reserved Space
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
0x02E8–
0x03FF Reserved R00000000
W
0x02C0–0x02E7 PWM (Pulse Width Modulator 8 Bit 8 Channel) (continued)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
64 Freescale Semiconductor
1.3.3 Part ID Assignments
The part ID is located in two 8-bit registers PARTIDH and PARTIDL (addresses 0x001A and 0x001B after
reset. The read-only value is a unique part ID for each revision of the chip. Table 1-7 shows the assigned
part ID number.
The device memory sizes are located in two 8-bit registers MEMSIZ0 and MEMSIZ1 (addresses 0x001C
and 0x001D after reset). Table 1-8 shows the read-only values of these registers. Refer to HCS12 Module
Mapping and Control (MMC) block description chapter for further details.
Table 1-7. Assigned Part ID Numbers
Device Mask Set Number Part ID1
1The coding is as follows:
Bit 15-12: Major family identifier
Bit 11-8: Minor family identifier
Bit 7-4: Major mask set revision number including FAB transfers
Bit 3-0: Minor - non full - mask set revision
MC9S12KG128 0L74N 0x7100
MC9S12KG128 1L74N 0x7101
MC9S12KG128 2L74N 0x7102
MC9S12KG128 3L74N 0x7103
MC9S12KG128 4L74N 0x7104
MC9S12KG128 5L74N 0x7105
Table 1-8. Memory Size Registers
Device Register Name Value
MC9S12KG128 MEMSIZ0 0x13
MC9S12KG128 MEMSIZ1 0x80
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 65
1.4 System Clock Description
The Clock and Reset Generator provides the internal clock signals for the core and all peripheral modules.
Figure 1-12 shows the clock connections from the CRG to all modules. Consult the CRG Block Guide for
details on clock generation.
Figure 1-12. Clock Connections
1.5 Modes of Operation
Eight possible modes determine the operating configuration of the MC9S12KG128. Each mode has an
associated default memory map and external bus configuration controlled by a further pin.
Three low power modes exist for the device.
1.5.1 Chip Configuration Summary
The operating mode out of reset is determined by the states of the MODC, MODB, and MODA pins during
reset (Table 1-9). The MODC, MODB, and MODA bits in the MODE register show the current operating
mode and provide limited mode switching during operation. The states of the MODC, MODB, and MODA
pins are latched into these bits on the rising edge of the reset signal. The ROMCTL signal allows the setting
of the ROMON bit in the MISC register thus controlling whether the internal Flash is visible in the memory
CRG BUS CLOCK
CORE CLOCK
EXTAL
XTAL OSCILLATOR CLOCK
HCS12 CORE
Flash
BDM
OSC
CPU
MEBI MMC
INT DBG
IIC
RAM
SCI0, SCI1
PWM
ATD
EEPROM
TIM
SPI0, SPI1, SPI2
CAN0, CAN4
PIM
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
66 Freescale Semiconductor
map. ROMON = 1 mean the Flash is visible in the memory map. The state of the ROMCTL pin is latched
into the ROMON bit in the MISC register on the rising edge of the reset signal.
For further explanation on the modes refer to the HCS12 MEBI block description chapter.
Table 1-9. Mode Selection
BKGD =
MODC PE6 =
MODB PE5 =
MODA PK7 =
ROMCTL ROMON
Bit Mode Description
0 0 0 X 1 Special Single Chip, BDM allowed and ACTIVE. BDM is
allowed in all other modes but a serial command is
required to make BDM active.
00101Emulation Expanded Narrow, BDM allowed
10
0 1 0 X 0 Special Test (Expanded Wide), BDM allowed
01101Emulation Expanded Wide, BDM allowed
10
1 0 0 X 1 Normal Single Chip, BDM allowed
10100Normal Expanded Narrow, BDM allowed
11
1 1 0 X 1 Peripheral; BDM allowed but bus operations would cause
bus conflicts (must not be used)
11100Normal Expanded Wide, BDM allowed
11
Table 1-10. Clock Selection Based on PE7
PE7 = XCLKS Description
1 Loop Controlled Pierce Oscillator selected
0 Full Swing Pierce Oscillator or external clock selected
Table 1-11. Voltage Regulator VREGEN
VREGEN Description
1 Internal Voltage Regulator enabled
0 Internal Voltage Regulator disabled, VDD1,2 and
VDDPLL must be supplied externally with 2.5V
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 67
1.5.2 Security
The device will make available a security feature preventing the unauthorized read and write of the
memory contents. This feature allows:
Protection of the contents of FLASH,
Protection of the contents of EEPROM,
Operation in single-chip mode,
Operation from external memory with internal FLASH and EEPROM disabled.
The user must be reminded that part of the security must lie with the user’s code. An extreme example
would be user’s code that dumps the contents of the internal program. This code would defeat the purpose
of security. At the same time the user may also wish to put a back door in the user’s program. An example
of this is the user downloads a key through the SCI which allows access to a programming routine that
updates parameters stored in EEPROM.
1.5.2.1 Securing the Microcontroller
Once the user has programmed the FLASH and EEPROM (if desired), the part can be secured by
programming the security bits located in the FLASH module. These non-volatile bits will keep the part
secured through resetting the part and through powering down the part.
The security byte resides in a portion of the Flash array.
Check the Flash Block Guide for more details on the security configuration.
1.5.2.2 Operation of the Secured Microcontroller
1.5.2.2.1 Normal Single Chip Mode
This will be the most common usage of the secured part. Everything will appear the same as if the part was
not secured with the exception of BDM operation. The BDM operation will be blocked.
1.5.2.2.2 Executing from External Memory
The user may wish to execute from external space with a secured microcontroller. This is accomplished
by resetting directly into expanded mode. The internal FLASH and EEPROM will be disabled. BDM
operations will be blocked.
1.5.2.3 Unsecuring the Microcontroller
In order to unsecure the microcontroller, the internal FLASH and EEPROM must be erased. This can be
done through an external program in expanded mode.
Once the user has erased the FLASH and EEPROM, the part can be reset into special single chip mode.
This invokes a program that verifies the erasure of the internal FLASH and EEPROM. Once this program
completes, the user can erase and program the FLASH security bits to the unsecured state. This is generally
done through the BDM, but the user could also change to expanded mode (by writing the mode bits
through the BDM) and jumping to an external program (again through BDM commands). Note that if the
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
68 Freescale Semiconductor
part goes through a reset before the security bits are reprogrammed to the unsecure state, the part will be
secured again.
1.5.3 Low Power Modes
The microcontroller features three main low power modes. Consult the respective Block Guide for
information on the module behavior in Stop, Pseudo Stop, and Wait Mode. An important source of
information about the clock system is the Clock and Reset Generator Guide (CRG).
1.5.3.1 Stop
Executing the CPU STOP instruction stops all clocks and the oscillator thus putting the chip in fully static
mode. Wake up from this mode can be done via reset or external interrupts.
1.5.3.2 Pseudo Stop
This mode is entered by executing the CPU STOP instruction. In this mode the oscillator is still running
and the Real Time Interrupt (RTI) or Watchdog (COP) sub module can stay active. Other peripherals are
turned off. This mode consumes more current than the full STOP mode, but the wake up time from this
mode is significantly shorter.
1.5.3.3 Wait
This mode is entered by executing the CPU WAI instruction. In this mode the CPU will not execute
instructions. The internal CPU signals (address and data bus) will be fully static. All peripherals stay
active. For further power consumption the peripherals can individually turn off their local clocks.
1.5.3.4 Run
Although this is not a low power mode, unused peripheral modules should not be enabled in order to save
power.
1.6 Resets and Interrupts
Consult the Exception Processing section of the CPU12 Reference Manual for information on resets and
interrupts. Both local masking and CCR masking are included as listed in Table 1-12. System resets can
be generated through external control of the RESET pin, through the clock and reset generator module
CRG or through the low voltage reset (LVR) generator of the voltage regulator module. Refer to the CRG
and VREG block description chapters for detailed information on reset generation.
1.6.1 Vectors
1.6.1.1 Vector Table
Table 1-12 lists interrupt sources and vectors in default order of priority.
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 69
Table 1-12. Interrupt Vector Locations
Vector
Address Interrupt
Source CCR
Mask Local
Enable HPRIO Value
to Elevate
0xFFFE, 0xFFFF External Reset, Power On Reset or Low
Voltage Reset (see CRG Flags Register
to determine reset source)
None None
0xFFFC, 0xFFFD Clock Monitor fail reset None PLLCTL (CME, FCME)
0xFFFA, 0xFFFB COP failure reset None COP rate select
0xFFF8, 0xFFF9 Unimplemented instruction trap None None
0xFFF6, 0xFFF7 SWI None None
0xFFF4, 0xFFF5 XIRQ X Bit None
0xFFF2, 0xFFF3 IRQ I Bit IRQCR (IRQEN) 0xF2
0xFFF0, 0xFFF1 Real Time Interrupt I Bit CRGINT (RTIE) 0xF0
0xFFEE, 0xFFEF Standard Timer channel 0 I Bit TIE (C0I) 0xEE
0xFFEC, 0xFFED Standard Timer channel 1 I Bit TIE (C1I) 0xEC
0xFFEA, 0xFFEB Standard Timer channel 2 I Bit TIE (C2I) 0xEA
0xFFE8, 0xFFE9 Standard Timer channel 3 I Bit TIE (C3I) 0xE8
0xFFE6, 0xFFE7 Standard Timer channel 4 I Bit TIE (C4I) 0xE6
0xFFE4, 0xFFE5 Standard Timer channel 5 I Bit TIE (C5I) 0xE4
0xFFE2, 0xFFE3 Standard Timer channel 6 I Bit TIE (C6I) 0xE2
0xFFE0, 0xFFE1 Standard Timer channel 7 I Bit TIE (C7I) 0xE0
0xFFDE, 0xFFDF Standard Timer overflow I Bit TSCR2 (TOI) 0xDE
0xFFDC, 0xFFDD Pulse accumulator overflow I Bit PACTL (PAOVI) 0xDC
0xFFDA, 0xFFDB Pulse accumulator input edge I Bit PACTL (PAI) 0xDA
0xFFD8, 0xFFD9 SPI0 I Bit SPICR1 (SPIE, SPTIE) 0xD8
0xFFD6, 0xFFD7 SCI0 I Bit SCICR2
(TIE, TCIE, RIE, ILIE) 0xD6
0xFFD4, 0xFFD5 SCI1 I Bit SCICR2
(TIE, TCIE, RIE, ILIE) 0xD4
0xFFD2, 0xFFD3 ATD I Bit ATDCTL2 (ASCIE) 0xD2
0xFFD0, 0xFFD1 Reserved I Bit Reserved 0xD0
0xFFCE, 0xFFCF Port J I Bit PIEJ
(PIEJ7, PIEJ6, PIEJ1, PIEJ0) 0xCE
0xFFCC, 0xFFCD Port H I Bit PIEH (PIEH7–0) 0xCC
0xFFCA, 0xFFCB Reserved I Bit Reserved 0xCA
0xFFC8, 0xFFC9 I Bit 0xC8
0xFFC6, 0xFFC7 CRG PLL lock I Bit CRGINT (LOCKIE) 0xC6
0xFFC4, 0xFFC5 CRG Self Clock Mode I Bit CRGINT (SCMIE) 0xC4
0xFFC2, 0xFFC3 FLASH Double Fault Detect I Bit FCNFG (DFDIE) 0xC2
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
70 Freescale Semiconductor
0xFFC0, 0xFFC1 IIC Bus I Bit IBCR (IBIE) 0xC0
0xFFBE, 0xFFBF SPI1 I Bit SPICR1 (SPIE, SPTIE) 0xBE
0xFFBC, 0xFFBD SPI2 I Bit SPICR1 (SPIE, SPTIE) 0xBC
0xFFBA, 0xFFBB EEPROM command I Bit ECNFG (CCIE, CBEIE) 0xBA
0xFFB8, 0xFFB9 FLASH command I Bit FCNFG (CCIE, CBEIE) 0xB8
0xFFB6, 0xFFB7 CAN0 wake-up I Bit CAN0RIER (WUPIE) 0xB6
0xFFB4, 0xFFB5 CAN0 errors I Bit CAN0RIER (CSCIE, OVRIE) 0xB4
0xFFB2, 0xFFB3 CAN0 receive I Bit CAN0RIER (RXFIE) 0xB2
0xFFB0, 0xFFB1 CAN0 transmit I Bit CAN0TIER (TXEIE2–TXEIE0) 0xB0
0xFFAE, 0xFFAF
Reserved
I Bit
Reserved
0xAE
0xFFAC, 0xFFAD I Bit 0xAC
0xFFAA, 0xFFAB I Bit 0xAA
0xFFA8, 0xFFA9 I Bit 0xA8
0xFFA6, 0xFFA7 I Bit 0xA6
0xFFA4, 0xFFA5 I Bit 0xA4
0xFFA2, 0xFFA3 I Bit 0xA2
0xFFA0, 0xFFA1 I Bit 0xA0
0xFF9E, 0xFF9F I Bit 0x9E
0xFF9C, 0xFF9D I Bit 0x9C
0xFF9A, 0xFF9B I Bit 0x9A
0xFF98, 0xFF99 I Bit 0x98
0xFF96, 0xFF97 CAN4 wake-up I Bit CAN4RIER (WUPIE) 0x96
0xFF94, 0xFF95 CAN4 errors I Bit CAN4RIER (CSCIE, OVRIE) 0x94
0xFF92, 0xFF93 CAN4 receive I Bit CAN4RIER (RXFIE) 0x92
0xFF90, 0xFF91 CAN4 transmit I Bit CAN4TIER (TXEIE2–TXEIE0) 0x90
0xFF8E, 0xFF8F Port P I Bit PIEP (PIEP7–0) 0x8E
0xFF8C, 0xFF8D PWM Emergency Shutdown I Bit PWMSDN (PWMIE) 0x8C
0xFF8A, 0xFF8B VREG Low Voltage Interrupt I Bit CTRL0 (LVIE) 0x8A
0xFF80 - 0xFF89 Reserved I Bit Reserved 0x80 - 0x89
Table 1-12. Interrupt Vector Locations (continued)
Vector
Address Interrupt
Source CCR
Mask Local
Enable HPRIO Value
to Elevate
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 71
1.6.2 Resets
Resets are a subset of the interrupts featured inTable 1-12. The different sources capable of generating a
system reset are summarized in Table 1-13.
1.6.2.1 Effects of Reset
When a reset occurs, MCU registers and control bits are changed to known start-up states. Refer to the
respective module block description chapters for register reset states.
Refer to the PIM block description chapter for reset configurations of all peripheral module ports.
Refer to Table 1-5 for locations of the memories depending on the operating mode after reset.
The RAM array is not automatically initialized out of reset.
1.7 ATD External Trigger Input Connection
The ATD module includes external trigger input ETRIG. On MC9S12KG128, the ETRIG input is tied to
GND.
Table 1-13. Reset Summary
Reset Priority Source Vector
Power-on Reset 1 CRG Module 0xFFFE, 0xFFFF
External Reset 1 RESET pin 0xFFFE, 0xFFFF
Low Voltage Reset 1 VREG Module 0xFFFE, 0xFFFF
Clock Monitor Reset 2 CRG Module 0xFFFC, 0xFFFD
COP Watchdog Reset 3 CRG Module 0xFFFA, 0xFFFB
Chapter 1 MC9S12KG128 Device Overview (MC9S12KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
72 Freescale Semiconductor
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 73
Chapter 2
128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
2.1 Introduction
This document describes the FTS128K1ECC module that includes a 128Kbyte Flash (nonvolatile)
memory with built-in Error Code Correction (ECC). The Flash memory may be read as either bytes,
aligned words, or misaligned words. Read access time is one bus cycle for bytes and aligned words, and
two bus cycles for misaligned words.
The Flash memory is ideal for program and data storage for single-supply applications allowing for field
reprogramming without requiring external voltage sources for program or erase. Program and erase
functions are controlled by a command driven interface. The Flash module supports both block erase and
sector erase. An erased bit reads 1 and a programmed bit reads 0. The high voltage required to program
and erase the Flash memory is generated internally. It is not possible to read from a Flash block while it is
being erased or programmed.
The ECC logic is included in the Flash module with the program and erase operations automatically
generating the ECC parity bits. The ECC logic implements a modified Hamming code capable of
correcting single bit faults and detecting double bit faults in each word of the Flash memory.
CAUTION
A Flash word must be in the erased state before being programmed.
Cumulative programming of bits within a Flash word is not allowed and will
result in invalid data stored.
2.1.1 Glossary
Command Write Sequence — A three-step MCU instruction sequence to execute built-in algorithms
(including program and erase) on the Flash memory.
Table 2-1. FTS128K1ECC Revision History
Version
Number Revision
Date Author Description of Changes
V01.01 01JUL03 1. Update Protection Address Range Tables.
2. Update Protection Scenarios FIgure.
V01.02 04APR05 1. Reformat document.
V01.03 15SEP06 1. Add address range restriction to data compress command.
2. Describe algorithm for data compress command.
3. Add note about margin read during data compress command.
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
74 Freescale Semiconductor
2.1.2 Features
128 Kbytes of Flash memory comprised of one 128 Kbyte block divided into 128 sectors of 1024
bytes with every word (two bytes) accompanied by 6 ECC parity bits
Single bit fault correction per word during read operations
Automated program and erase algorithm with generation of ECC parity bits
Interrupts on Flash command completion, command buffer empty and double bit fault detection
Fast sector erase and word program operation
2-stage command pipeline for faster multi-word program times
Sector erase abort feature for critical interrupt response
Flexible protection scheme to prevent accidental program or erase
Single power supply for all Flash operations including program and erase
Security feature to prevent unauthorized access to the Flash memory
Code integrity check using built-in data compression
2.1.3 Modes of Operation
Program, erase, erase verify, and data compress operations (please refer to Section 2.4.1 for details).
2.1.4 Block Diagram
A block diagram of the Flash module is shown in Figure 2-1.
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 75
Figure 2-1. FTS128K1ECC Block Diagram
2.2 External Signal Description
The Flash module contains no signals that connect off-chip.
2.3 Memory Map and Register Definition
This subsection describes the memory map and registers for the Flash module.
2.3.1 Module Memory Map
The Flash memory map is shown in Figure 2-2. The HCS12 architecture places the Flash memory
addresses between 0x4000 and 0xFFFF which corresponds to three 16-Kbyte pages. The content of the
FTS128K1ECC
Oscillator Clock
Divider
Clock
Command
Interface
Command Pipeline
comm2
Command
Interrupt
Request
FCLK
addr2
data2
comm1
addr1
data1
Flash Block
64K * 22 Bits
Protection
Security
Double Fault
Detect Interrupt
Request
Error Detection
and Correction
sector 0
sector 1
sector 127
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
76 Freescale Semiconductor
HCS12 core PPAGE register is used to map the logical middle page ranging from address 0x8000 to
0xBFFF to any physical 16 Kbyte page in the Flash memory. By placing 0x3E or 0x3F in the HCS12 Core
PPAGE register, the associated 16 Kbyte pages appear twice in the MCU memory map.
The FPROT register, described in Section 2.3.2.5, “Flash Protection Register (FPROT)”, can be set to
globally protect a Flash block. However, three separate memory regions, one growing upward from the
first address in the next-to-last page in the Flash block (called the lower region), one growing downward
from the last address in the last page in the Flash block (called the higher region), and the remaining
addresses in the Flash block, can be activated for protection. The Flash locations of these protectable
regions are shown in Table 2-3. The higher address region is mainly targeted to hold the boot loader code
because it covers the vector space. The lower address region can be used for EEPROM emulation in an
MCU without an EEPROM module because it can remain unprotected while the remaining addresses are
protected from program or erase.
Security information that allows the MCU to restrict access to the Flash module is stored in the Flash
configuration field, described in Table 2-2.
Table 2-2. Flash Configuration Field
Unpaged Flash
Address Paged Flash Address
(PPAGE 0x3F) Size
(bytes) Description
0xFF00 - 0xFF07 0xBF00-0xBF07 8 Backdoor Comparison Key
Refer to Section Section 2.6.1,
“Unsecuring the MCU using
Backdoor Key Access
0xFF08 - 0xFF0C 0xBF08-0xBF0C 5 Reserved
0xFF0D 0xBF0D 1 Flash Protection byte
Refer to Section 2.3.2.5, “Flash
Protection Register (FPROT)
0xFF0E 0xBF0E 1 Reserved
0xFF0F 0xBF0F 1 Flash Security byte
Refer to Section 2.3.2.2, “Flash
Security Register (FSEC)
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 77
Figure 2-2. Flash Memory Map
Flash Registers
MODULE BASE + 0x0000
0xFF00 - 0xFF0F, Flash Configuration Field
MODULE BASE + 0x000F
0x8000
(16 bytes)
Flash Protected Low Sectors
1, 2, 4, 8 Kbytes
FLASH_START = 0x4000
0x5000
0x4400
0x6000
16K PAGED
MEMORY
0x38 0x39 0x3A 0x3B
0x3E
0x3C 0x3D 0x3E 0x3F
Note: 0x38-0x3F correspond to the PPAGE register content
FLASH_END = 0xFFFF
0xF800
0xF000
0xC000
0xE000 Flash Protected High Sectors
2, 4, 8, 16 Kbytes
0x3F
0x4800
Flash Block
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
78 Freescale Semiconductor
The Flash module also contains a set of 16 control and status registers located in address space module
base + 0x0000 to module base + 0x000F. A summary of these registers is given in Table 2-4 while their
accessibility in normal and special modes is detailed in Section 2.3.2, “Register Descriptions”.
Table 2-3. Detailed Flash Memory Map Summary
MCU Address
Range PPAGE ProtectableLower
Range Protectable
Higher Range Block Relative
Address1
1Block Relative Address for 128 Kbyte Flash block consists of 17 address bits.
0x4000-0x7FFF Unpaged
(0x3E) 0x4000-0x43FF N.A. 0x18000-0x1BFFF
0x4000-0x47FF
0x4000-0x4FFF
0x4000-0x5FFF
0x8000-0xBFFF 0x38 N.A. N.A. 0x00000-0x03FFF
0x39 N.A. N.A. 0x04000-0x07FFF
0x3A N.A. N.A. 0x08000-0x0BFFF
0x3B N.A. N.A. 0x0C000-0x0FFFF
0x3C N.A. N.A. 0x10000-0x13FFF
0x3D N.A. N.A. 0x14000-0x17FFF
0x3E 0x8000-0x83FF N.A. 0x18000-0x1BFFF
0x8000-0x87FF
0x8000-0x8FFF
0x8000-0x9FFF
0x3F N.A. 0xB800-0xBFFF 0x1C000-0x1FFFF
0xB000-0xBFFF
0xA000-0xBFFF
0x8000-0xBFFF
0xC000-0xFFFF Unpaged
(0x3F) N.A. 0xF800-0xFFFF 0x1C000-0x1FFFF
0xF000-0xFFFF
0xE000-0xFFFF
0xC000-0xFFFF
Table 2-4. Flash Register Map
MODULE
BASE + Use Normal Mode
Access
0x0000 Flash Clock Divider Register (FCLKDIV) R/W
0x0001 Flash Security Register (FSEC) R
0x0002 Flash Test Mode Register (FTSTMOD) R/W
0x0003 Flash Configuration Register (FCNFG) R/W
0x0004 Flash Protection Register (FPROT) R/W
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 79
0x0005 Flash Status Register (FSTAT) R/W
0x0006 Flash Command Register (FCMD) R/W
0x0007 RESERVED11R
0x0008 Flash High Address Register (FADDRHI) R
0x0009 Flash Low Address Register (FADDRLO) R
0x000A Flash High Data Register (FDATAHI) R
0x000B Flash Low Data Register (FDATALO) R
0x000C RESERVED21R
0x000D RESERVED31R
0x000E RESERVED41R
0x000F RESERVED51R
1Intended for factory test purposes only.
Table 2-4. Flash Register Map
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
80 Freescale Semiconductor
2.3.2 Register Descriptions
Register
Name Bit 7 654321Bit 0
0x0000
FCLKDIV RFDIVLD PRDIV8 FDIV5 FDIV4 FDIV3 FDIV2 FDIV1 FDIV0
W
0x0001
FSEC R KEYEN RNV5 RNV4 RNV3 RNV2 SEC
W
0x0002
FTSTMOD R00000000
W
0x0003
FCNFG RCBEIE CCIE KEYACC 00000
W
0x0004
FPROT RFPOPEN RNV6 FPHDIS FPHS FPLDIS FPLS
W
0x0005
FSTAT RCBEIF CCIF PVIOL ACCERR 0 BLANK 0 0
W
0x0006
FCMD R0 CMDB
W
0x0007
FCTL R NV7 NV6 NV5 NV4 NV3 NV2 NV1 NV0
W
0x0008
FADDRHI R FADDRHI
W
0x0009
FADDRLO R FADDRLO
W
0x000A
FDATAHI R FDATAHI
W
0x000B
FDATALO R FDATALO
W
0x000C
RESERVED1 R00000000
W
= Unimplemented or Reserved
Figure 2-3. FTS128K1ECC Register Summary
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 81
2.3.2.1 Flash Clock Divider Register (FCLKDIV)
The FCLKDIV register is used to control timed events in program and erase algorithms.
All bits in the FCLKDIV register are readable, bits 6-0 are write once and bit 7 is not writable.
0x000D
RESERVED2 R00000000
W
0x000E
RESERVED3 R00000000
W
0x000F
RESERVED4 R00000000
W
Module Base + 0x0000
76543210
R FDIVLD PRDIV8 FDIV5 FDIV4 FDIV3 FDIV2 FDIV1 FDIV0
W
Reset 00000000
= Unimplemented or Reserved
Figure 2-4. Flash Clock Divider Register (FCLKDIV)
Table 2-5. FCLKDIV Field Descriptions
Field Description
7
FDIVLD Clock Divider Loaded.
0 Register has not been written.
1 Register has been written to since the last reset.
6
PRDIV8 Enable Prescalar by 8.
0 The oscillator clock is directly fed into the clock divider.
1 The oscillator clock is divided by 8 before feeding into the clock divider.
5-0
FDIV[5:0] Clock Divider Bits — The combination of PRDIV8 and FDIV[5:0] must divide the oscillator clock down to a
frequency of 150 kHz–200 kHz. The maximum divide ratio is 512. Please refer to Section 2.4.1.1, “Writing the
FCLKDIV Register” for more information.
Register
Name Bit 7 654321Bit 0
= Unimplemented or Reserved
Figure 2-3. FTS128K1ECC Register Summary (continued)
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
82 Freescale Semiconductor
2.3.2.2 Flash Security Register (FSEC)
The FSEC register holds all bits associated with the security of the MCU and Flash module.
All bits in the FSEC register are readable but are not writable.
The FSEC register is loaded from the Flash Configuration Field at address $FF0F during the reset
sequence, indicated by F in Figure 2-5. If the DFDIF flag in the FSTAT register is set while reading the
securityfieldlocation during the resetsequence,all bits in theFSEC register will be settoleave the module
in a secured state with backdoor key access disabled.
Module Base + 0x0001
76543210
R KEYEN RNV5 RNV4 RNV3 RNV2 SEC
W
Reset F F FFFFFF
= Unimplemented or Reserved
Figure 2-5. Flash Security Register (FSEC)
Table 2-6. FSEC Field Descriptions
Field Description
1-0
KEYEN[1:0] Backdoor Key Security Enable Bits —The KEYEN[1:0] bits define the enabling of backdoor key access to the
Flash module as shown in Table 2-7.
5-2
RNV[5:2] Reserved Nonvolatile Bits — The RNV[5:2] bits must remain in the erased 1 state for future enhancements.
1-0
SEC[1:0] Flash Security Bits The SEC[1:0] bits define the security state of the MCU as shown in Table 2-8. If the Flash
module is unsecured using backdoor key access, the SEC bits are forced to 10.
Table 2-7. Flash KEYEN States
KEYEN[1:0] Status of Backdoor Key Access
00 DISABLED
011
1Preferred KEYEN state to disable Backdoor Key Access.
DISABLED
10 ENABLED
11 DISABLED
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 83
The security function in the Flash module is described in Section 2.6, “Flash Module Security”.
2.3.2.3 Flash Test Mode Register (FTSTMOD)
The FTSTMOD register is used to control Flash test features.
FDFD is readable and writable while all remaining bits read 0 and are not writable in normal mode.
2.3.2.4 Flash Configuration Register (FCNFG)
The FCNFG register enables the Flash interrupts and gates the security backdoor writes.
Table 2-8. Flash Security States
SEC[1:0] Status of Security
00 SECURED
011
1Preferred SEC state to set MCU to secured state.
SECURED
10 UNSECURED
11 SECURED
Module Base + 0x0002
76543210
R0000
FDFD 000
W
Reset 00000000
= Unimplemented or Reserved
Figure 2-6. Flash Test Mode Register (FTSTMOD)
Table 2-9. FTSTMOD Field Descriptions
Field Description
3
FDFD Force Double Fault Detect — The FDFD bit allows the user to simulate a double bit fault during Flash array
read operations and check the associated interrupt routine. The FDFD bit is cleared by writing a 0 to FDFD.
0 Flash array read operations will set the DFDIF flag in the FSTAT register only if a double bit fault is detected.
1 Any Flash array read operation will force the DFDIF flag in the FSTAT register to be set and an interrupt will
be generated as long as the DFDIE interrupt enable in the FCNFG register is set.
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
84 Freescale Semiconductor
CBEIE, CCIE, KEYACC and DFDIE bits are readable and writable while all remaining bits read 0 and
are not writable. KEYACC is only writable if KEYEN (see Section 2.3.2.2) is set to the enabled state.
2.3.2.5 Flash Protection Register (FPROT)
The FPROT register defines which Flash sectors are protected against program or erase operations.
All bits in the FPROT register are readable and writable with restrictions except for RNV[6] which is only
readable (see Section 2.3.2.6, “Flash Protection Restrictions”).
During reset, the FPROT register is loaded from the Flash Configuration Field at address 0xFF0D. To
change the Flash protection that will be loaded during the reset sequence, the upper sector of the Flash
memory must be unprotected, then the Flash Protect/Security byte located as described in Table 2-2 must
be reprogrammed. If the DFDIF flag in the FSTAT register is set while reading the protection field location
Module Base + 0x0003
76543210
RCBEIE CCIE KEYACC 000 BKSEL
W
Reset 00000000
= Unimplemented or Reserved
Figure 2-7. Flash Configuration Register (FCNFG)
Table 2-10. FCNFG Field Descriptions
Field Description
7
CBEIE Command Buffer Empty Interrupt Enable TheCBEIEbit enablesan interrupt in case of anempty command
buffer in the Flash module.
0 Command buffer empty interrupt disabled.
1 Aninterrupt will be requested wheneverthe CBEIF flag (see Section 2.3.2.7, “Flash Status Register (FSTAT)”)
is set.
6
CCIE Command Complete Interrupt Enable The CCIE bit enables an interrupt in case all commands have been
completed in the Flash module.
0 Command complete interrupt disabled.
1 An interrupt will be requested whenever the CCIF flag (see Section 2.3.2.7, “Flash Status Register (FSTAT)”)
is set.
5
KEYACC Enable Security Key Writing
0 Flash writes are interpreted as the start of a command write sequence.
1 Writes to Flash array are interpreted as keys to open the backdoor. Reads of the Flash array return invalid
data.
3
DFDIE Double Fault Detect Interrupt Enable — The DFDIE bit enables an interrupt in case a double bit fault is
detected during a Flash block operation.
0 Double bit fault detect interrupt disabled.
1 An interrupt will be requested whenever the DFDIF flag is set (see Section 2.3.2.7, “Flash Status Register
(FSTAT)”).
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 85
during the reset sequence, the FPOPEN bit will be cleared and remaining bits in the FPROT register will
be set to leave the Flash block fully protected.
Trying to alter data in any of the protected areas in the Flash block will result in a protection violation error
and the PVIOL flag will be set in the FSTAT register. A mass erase of the Flash block is not possible if
any of the contained Flash sectors are protected.
Table 2-11. FPROT Field Descriptions
Field Description
7
FPOPEN Protection Function Bit The FPOPEN bit determines the protection function for program or erase as shown
in Table 2-12.
0 FPHDIS and FPLDIS bits define unprotected address ranges as specified by the corresponding FPHS[1:0]
and FPLS[1:0] bits. For an MCU without an EEPROM module, the FPOPEN clear state allows the main part
of the Flash block to be protected while a small address range can remain unprotected for EEPROM
emulation.
1 FPHDIS and FPLDIS bits enable protection for the address range specified by the corresponding FPHS[1:0]
and FPLS[1:0] bits.
6
RNV[6] Reserved Nonvolatile Bit — The RNV[6] bit must remain in the erased state 1 for future enhancements.
5
FPHDIS Flash Protection Higher Address Range Disable — The FPHDIS bit determines whether there is a
protected/unprotected area in the higher address space of the Flash block.
0 Protection/Unprotection enabled
1 Protection/Unprotection disabled
4:3
FPHS[1:0] Flash Protection Higher Address Size The FPHS[1:0] bits determine the size of the protected/unprotected
area as shown in Table 2-13. The FPHS[1:0] bits can only be written to while the FPHDIS bit is set.
2
FPLDIS Flash Protection Lower address range Disable — The FPLDIS bit determines whether there is a
protected/unprotected area in the lower address space of the Flash block.
0 Protection/Unprotection enabled
1 Protection/Unprotection disabled
1:0
FPLS[1:0] Flash Protection Lower Address Size The FPLS[1:0] bits determine the size of the protected/unprotected
area as shown in Table 2-14. The FPLS[1:0] bits can only be written to while the FPLDIS bit is set.
Table 2-12. Flash Protection Function
FPOPEN FPHDIS FPLDIS Function1
1For range sizes, refer to and .
1 1 1 No Protection
1 1 0 Protected Low Range
1 0 1 Protected High Range
1 0 0 Protected High and Low Ranges
0 1 1 Full Block Protected
0 1 0 Unprotected Low Range
0 0 1 Unprotected High Range
0 0 0 Unprotected High and Low Ranges
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
86 Freescale Semiconductor
All possible Flash protection scenarios are illustrated in Figure 2-8. Although the protection scheme is
loaded from the Flash array after reset, it can be changed by the user. This protection scheme can be used
by applications requiring re-programming in single-chip mode while providing as much protection as
possible if re-programming is not required.
Table 2-13. Flash Protection Higher Address Range
FPHS[1:0] Unpaged
Address Range Paged
Address Range Protected Size
00 0xF800-0xFFFF 0x3F: 0xC800-0xCFFF 2 Kbytes
01 0xF000-0xFFFF 0x3F: 0xC000-0xCFFF 4 Kbytes
10 0xE000-0xFFFF 0x3F: 0xB000-0xCFFF 8 Kbytes
11 0xC000-0xFFFF 0x3F: 0x8000-0xCFFF 16 Kbytes
Table 2-14. Flash Protection Lower Address Range
FPLS[1:0] Unpaged
Address Range Paged
Address Range Protected Size
00 0x4000-0x43FF 0x3E: 0x8000-0x83FF 1 Kbyte
01 0x4000-0x47FF 0x3E: 0x8000-0x87FF 2 Kbytes
10 0x4000-0x4FFF 0x3E: 0x8000-0x8FFF 4 Kbytes
11 0x4000-0x5FFF 0x3E: 0x8000-0x9FFF 8 Kbytes
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 87
Figure 2-8. Flash Protection Scenarios
7654
FPHS[1:0] FPLS[1:0]
3210
FPHS[1:0] FPLS[1:0]
FPHDIS=1
FPLDIS=1
FPHDIS=1
FPLDIS=0
FPHDIS=0
FPLDIS=1
FPHDIS=0
FPLDIS=0
Scenario
Scenario
Unprotected region Protected region with size
Protected region Protected region with size
defined by FPLS
defined by FPHSnot defined by FPLS, FPHS
FPOPEN=1FPOPEN=0
PPAGE 0x38-0x3D
PPAGE 0x3E-0x3F
PPAGE 0x38-0x3D
PPAGE 0x3E-0x3F
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
88 Freescale Semiconductor
2.3.2.6 Flash Protection Restrictions
The general guideline is that Flash protection can only be added and not removed. Table 2-15 specifies all
valid transitions between Flash protection scenarios. Any attempt to write an invalid scenario to the
FPROT register will be ignored and the FPROT register will remain unchanged. The contents of the
FPROT register reflect the active protection scenario. See the FPHS and FPLS descriptions for additional
restrictions.
2.3.2.7 Flash Status Register (FSTAT)
The FSTAT register defines the operational status of the module.
Table 2-15. Flash Protection Scenario Transitions
From
Protection
Scenario
To Protection Scenario1
1Allowed transitions marked with X.
01234567
0 XXXX
1XX
2XX
3X
4XX
5 XXXX
6XXXX
7 XXXXXXXX
Module Base + 0x0005
76543210
RCBEIF CCIF PVIOL ACCERR DFDIF BLANK 0 0
W
Reset 11000000
= Unimplemented or Reserved
Figure 2-9. Flash Status Register (FSTAT - Normal Mode)
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 89
CBEIF, PVIOL, ACCERR and DFDIF are readable and writable, CCIF and BLANK are readable and not
writable, remaining bits read 0 and are not writable in normal mode. FAIL is readable and writable in
special mode. FAIL must be clear when starting a command write sequence.
Module Base + 0x0005
76543210
RCBEIF CCIF PVIOL ACCERR DFDIF BLANK FAIL 0
W
Reset 11000000
= Unimplemented or Reserved
Figure 2-10. Flash Status Register (FSTAT - Special Mode)
Table 2-16. FSTAT Field Descriptions
Field Description
7
CBEIF Command Buffer Empty Interrupt Flag — The CBEIF flag indicates that the address, data and command
buffers are empty so that a new command write sequence can be started. The CBEIF flag is cleared by writing
a 1 to CBEIF. Writing a 0 to the CBEIF flag has no effect on CBEIF. Writing a 0 to CBEIF after writing an aligned
word to the Flash address space but before CBEIF is cleared will abort a command write sequence and cause
the ACCERR flag to be set. Writing a 0 to CBEIF outside of a command write sequence will not set the ACCERR
flag. The CBEIF flag is used together with the CBEIE bit in the FCNFG register to generate an interrupt request
(see Figure 2-31).
0 Buffers are full.
1 Buffers are ready to accept a new command.
6
CCIF Command Complete Interrupt Flag The CCIF flag indicatesthat there are no morecommandspending. The
CCIF flag is cleared when CBEIF is clear and sets automatically upon completion of all active and pending
commands. The CCIF flag does not set when an active commands completes and a pending command is
fetched from the command buffer. Writing to the CCIF flag has no effect on CCIF. The CCIF flag is used together
with the CCIE bit in the FCNFG register to generate an interrupt request (see Figure 2-31).
0 Command in progress.
1 All commands are completed.
5
PVIOL Protection Violation Flag — The PVIOL flag indicates an attempt was made to program or erase an address
in a protected area of the Flash block during a command write sequence. The PVIOL flag is cleared by writing a
1 to PVIOL. Writing a 0 to the PVIOL flag has no effect on PVIOL. While PVIOL is set, it is not possible to launch
a command or start a command write sequence.
0 No failure.
1 A protection violation has occurred.
4
ACCERR Access Error Flag — The ACCERR flag indicates an illegal access to the Flash array caused by either a
violation of the command write sequence, issuing an illegal command (illegal combination of the CMDBx bits in
the FCMD register), launching the sector erase abort command terminating a sector erase operation early,
detection of a double fault or the execution of a CPU STOP instruction while a command is executing (CCIF =
0). The ACCERR flag is cleared by writing a 1 to ACCERR. Writing a 0 to the ACCERR flag has no effect on
ACCERR. While ACCERR is set, it is not possible to launch a command or start a command write sequence. If
ACCERR is set by the detection of a double fault, an erase verify operation or a data compress operation, any
buffered command will not launch.
0 No access error detected.
1 Access error has occurred.
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
90 Freescale Semiconductor
2.3.2.8 Flash Command Register (FCMD)
The FCMD register is the Flash command register.
All CMDB bits are readable and writable during a command write sequence while bit 7 reads 0 and is not
writable.
3
DFDIF Double Fault Detect Interrupt Flag The DFDIF flag indicates that one of the following Flash block operations
has detected a double bit fault in the stored parity and data bits.
Array Read.
Erase Verify.
Data Compress.
Reset Sequence (reads of the protection and security fields stored in the Flash memory).
When the DFDIF flag is set during a Flash array read operation, the data read from the Flash module are the
data bits read out of the Flash array without correction and should be considered invalid. When the DFDIF flag
is set during a Flash array read, erase verify, data compress or reset sequence operation, the Flash block
address containing the parity and data bits that caused the DFDIF flag to set will be stored in the FADDR register
and the parity bits will be stored in the FDATA register. The DFDIF flag is cleared by writing a 1 to the ACCERR
bit which is set when the DFDIF flag is set. Writing a 0 to the DFDIF flag has no effect on DFDIF. TheDFDIF flag
is used together with the DFDIE enable bit to generate an interrupt request (see Figure 2-31). While DFDIF is
set, Flash array read operations are allowed. If DFDIF is not cleared and another double bit fault is detected, the
FADDR and FDATA registers will maintain the contents from the fault that caused the DFDIF bit to set.
0 No double bit fault detected.
1 Double bit fault detected.
2
BLANK Erase Verify Operation Status Flag When the CCIF flag is set after completion of an erase verify command,
the BLANK flag indicates the result of the erase verify operation. The BLANK flag is cleared by the Flash module
when CBEIF is cleared as part of a new valid command write sequence. Writing to the BLANK flag has no effect
on BLANK.
0 Flash block verified as not erased.
1 Flash block verified as erased.
1
FAIL Flag Indicating a Failed Flash Operation The FAIL flag will set if the erase verify operation fails (Flash block
verified as not erased). The FAIL flag will also set if a double bit fault is detected during an array read, erase
verify, or data compress operation. The FAIL flag is cleared by writing a 1 to FAIL. Writing a 0 to the FAIL flag
has no effect on FAIL.
0 Flash operation completed without error.
1 Flash operation failed.
Module Base + 0x0006
76543210
R0 CMDB
W
Reset 00000000
= Unimplemented or Reserved
Figure 2-11. Flash Command Register (FCMD - NVM User Mode)
Table 2-16. FSTAT Field Descriptions
Field Description
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 91
2.3.2.9 RESERVED1
This register is reserved for factory testing and is not accessible.
All bits read 0 and are not writable.
2.3.2.10 Flash Address Registers (FADDR)
The FADDRHI and FADDRLO registers are the Flash address registers.
Table 2-17. FCMD Field Descriptions
Field Description
6-0
CMDB[6:0] Flash Command — Valid Flash commands are shown in Table 2-18. Writing any command other than those
listed in Table 2-18 sets the ACCERR flag in the FSTAT register.
Table 2-18. Valid Flash Command List
CMDB[6:0] NVM Command
0x05 Erase Verify
0x06 Data Compress
0x20 Word Program
0x40 Sector Erase
0x41 Mass Erase
0x47 Sector Erase Abort
Module Base + 0x0007
76543210
R00000000
W
Reset 00000000
= Unimplemented or Reserved
Figure 2-12. RESERVED1
Table 2-19. FCTL Field Descriptions
Field Description
7-0
NV[7:0] Nonvolatile Bits The NV[7:0] bits are available as nonvolatile bits. Refer to the Device User Guide for proper
use of the NV bits.
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
92 Freescale Semiconductor
All FADDRHI and FADDRLO bits are readable but are not writable. After an array write as part of a
command write sequence, the FADDR registers will contain the mapped MCU address written. If a double
bit fault is detected, as indicated by the setting of the DFDIF bit in the FSTAT register, the faulty Flash
block address is stored in the FADDR registers as a word address. The faulty Flash block address remains
readable until the start of the next command write sequence. The mapping of the FADDR registers to the
MCU address is shown in Figure 2-15 and Figure 2-16.
Figure 2-15. FADDR to MCU Address Mapping (Paged)
Module Base + 0x0008
76543210
R FADDRHI
W
Reset 00000000
= Unimplemented or Reserved
Figure 2-13. Flash Address High Register (FADDRHI)
Module Base + 0x0009
76543210
R FADDRLO
W
Reset 00000000
= Unimplemented or Reserved
Figure 2-14. Flash Address Low Register (FADDRLO)
AB1AB2AB3AB4AB5AB6AB7AB8AB9AB10AB11AB12AB13
Byte Select
FADDRLO[7:0]
FADDRHI[7:0]
MCU Address
FADDR Register
PPAGE Register PIX2 PIX1 PIX0111
01 AB0
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 93
Figure 2-16. FADDR to MCU Address Mapping (Unpaged)
2.3.2.11 Flash Data Registers (FDATA)
The FDATAHI and FDATALO registers are the Flash data registers.
All FDATAHI and FDATALO bits are readable but are not writable. After an array write as part of a
command write sequence, the FDATA registers will contain the data written. At the completion of a data
compress operation, the resulting 16-bit signature is stored in the FDATA registers. The data compression
signature is readable in the FDATA registers until a new command write sequence is started or a double bit
fault is detected in a Flash array read operation.If a double bit fault is detected during a Flash array read,
erase verify or data compress operation, the parity bits stored in the Flash array at the failed location will
Module Base + 0x000A
76543210
R FDATAHI
W
Reset 00000000
= Unimplemented or Reserved
Figure 2-17. Flash Data High Register (FDATAHI)
Module Base + 0x000B
76543210
R FDATALO
W
Reset 00000000
= Unimplemented or Reserved
Figure 2-18. Flash Data Low Register (FDATALO)
AB1AB2AB3AB4AB5AB6AB7AB8AB9AB10AB11AB12AB13
Byte Select
FADDRLO[7:0]
FADDRHI[4:0]
MCU Address (0x4000-0x7FFF)
FADDR Register
10 AB0
AB1AB2AB3AB4AB5AB6AB7AB8AB9AB10AB11AB12AB13
Byte Select
MCU Address (0xC000-0xFFFF) 11 AB0
1
0
11
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
94 Freescale Semiconductor
be stored in the lower six bits of FDATALO. The faulty parity bits remain readable until the start of the
next command write sequence.
2.3.2.12 RESERVED2
This register is reserved for factory testing and is not accessible.
All bits read 0 and are not writable.
2.3.2.13 RESERVED3
This register is reserved for factory testing and is not accessible.
All bits read 0 and are not writable.
2.3.2.14 RESERVED4
This register is reserved for factory testing and is not accessible.
Module Base + 0x000C
76543210
R00000000
W
Reset 00000000
= Unimplemented or Reserved
Figure 2-19. RESERVED2
Module Base + 0x000D
76543210
R00000000
W
Reset 00000000
= Unimplemented or Reserved
Figure 2-20. RESERVED3
Module Base + 0x000E
76543210
R00000000
W
Reset 00000000
= Unimplemented or Reserved
Figure 2-21. RESERVED4
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 95
All bits read 0 and are not writable.
2.3.2.15 RESERVED5
This register is reserved for factory testing and is not accessible.
All bits read 0 and are not writable.
2.4 Functional Description
2.4.1 Flash Command Operations
Write and read operations are both used for the program, erase, erase verify, and data compress algorithms
described in this subsection. The program and erase algorithms are time controlled by a state machine
whose timebase, FCLK, is derived from the oscillator clock via a programmable divider. The command
register as well as the associated address and data registers operate as a buffer and a register (2-stage FIFO)
so that a second command along with the necessary data and address can be stored to the buffer while the
first command remains in progress. This pipelined operation allows a time optimization when
programming more than one word on a specific row in the Flash block as the high voltage generation can
be kept active in between two programming commands. The pipelined operation also allows a
simplification of command launching. Buffer empty as well as command completion are signalled by flags
in the Flash status register with interrupts generated, if enabled.
The next paragraphs describe:
1. How to write the FCLKDIV register.
2. Command write sequences used to program, erase, and verify the Flash memory.
3. Valid Flash commands.
4. Effects resulting from illegal Flash command write sequences or aborting Flash operations.
2.4.1.1 Writing the FCLKDIV Register
Prior to issuing any program, erase, erase verify, or data compress command, it is first necessary to write
the FCLKDIV register to divide the oscillator clock down to within the 150 kHz to 200 kHz range.
Because the program and erase timings are also a function of the bus clock, the FCLKDIV determination
must take this information into account.
Module Base + 0x000F
76543210
R00000000
W
Reset 00000000
= Unimplemented or Reserved
Figure 2-22. RESERVED5
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
96 Freescale Semiconductor
If we define:
FCLK as the clock of the Flash timing control block,
Tbus as the period of the bus clock, and
INT(x) as taking the integer part of x (e.g. INT(4.323)=4).
Then, FCLKDIV register bits PRDIV8 and FDIV[5:0] are to be set as described in Figure 2-23.
For example, if the oscillator clock frequency is 950 kHz and the bus clock frequency is 10 MHz,
FCLKDIV bits FDIV[5:0] must be set to 4 (000100) and bit PRDIV8 set to 0. The resulting FCLK
frequency is then 190 kHz. As a result, the Flash program and erase algorithm timings are increased over
the optimum target by:
CAUTION
Program and erase command execution time will increase proportionally
with the period of FCLK. Because of the impact of clock synchronization
on the accuracy of the functional timings, programming or erasing the Flash
memory cannot be performed if the bus clock runs at less than 1 MHz.
Programming or erasing the Flash memory with FCLK < 150 kHz must be
avoided. Setting FCLKDIV to a value such that FCLK < 150 kHz can
destroy the Flash memory due to overstress. Setting FCLKDIV to a value
such that (1/FCLK + Tbus) < 5µs can result in incomplete programming or
erasure of the Flash memory cells.
If the FCLKDIV register is written, the FDIVLD bit is set automatically. If the FDIVLD bit is 0, the
FCLKDIV register has not been written since the last reset. Flash commands will not be executed if the
FCLKDIV register has not been written to.
200 190()200100×5%=
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 97
Figure 2-23. Determination Procedure for PRDIV8 and FDIV Bits
PRDIV8=1
YES
NO
PRDIV8=0 (reset)
FCLK=(PRDCLK)/(1+FDIV[5:0])
PRDCLK=oscillator_clock
PRDCLK=oscillator_clock/8
PRDCLK[MHz]*(5+Tbus[µs]) NO
FDIV[5:0]=PRDCLK[MHz]*(5+Tbus[µs])-1
YES
START
Tbus < 1µs?
an integer?
FDIV[5:0]=INT(PRDCLK[MHz]*(5+Tbus[µs]))
1/FCLK[MHz] + Tbus[µs] > 5
AND
FCLK > 0.15 MHz
?
END
YES
NO
FDIV[5:0] > 4?
ALL COMMANDS IMPOSSIBLE
YES
NO
ALL COMMANDS IMPOSSIBLE
NO
TRY TO DECREASE Tbus
YES
OSCILLATOR
CLOCK
> 12.8 MHZ?
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
98 Freescale Semiconductor
2.4.1.2 Command Write Sequence
The Flash command controller is used to supervise the command write sequence to execute program,
erase, erase verify, and data compress algorithms.
Before starting a command write sequence, the ACCERR and PVIOL flags in the FSTAT register must be
clear (see Section 2.3.2.7, “Flash Status Register (FSTAT)”) and the CBEIF flag must be tested to
determine the state of the address, data, and command buffers. If the CBEIF flag is set, indicating the
buffers are empty, a new command write sequence can be started. If the CBEIF flag is clear, indicating the
buffers are not available, a new command write sequence will overwrite the contents of the address, data,
and command buffers.
A command write sequence consists of three steps which must be strictly adhered to with writes to the
Flash module not permitted between the steps. However, Flash register and array reads are allowed during
a command write sequence. A command write sequence consists of the following steps:
1. Write an aligned data word to a valid Flash array address. The address and data will be stored in
the address and data buffers, respectively. If the CBEIF flag is clear when the Flash array write
occurs, the contents of the address and data buffers will be overwritten and the CBEIF flag will be
set.
2. Write a valid command to the FCMD register.
a) For the erase verify command (see Section 2.4.1.3.1, “Erase Verify Command”), the contents
of the data buffer are ignored and all address bits in the address buffer are ignored.
b) For the data compress command (see Section 2.4.1.3.2, “Data Compress Command”), the
contents of the data buffer represents the number of consecutive words to read for data
compression and the contents of the address buffer represents the starting address.
c) For the program command (see Section 2.4.1.3.3, “Program Command”), the contents of the
data buffer will be programmed to the address specified in the address buffer with all address
bits valid.
d) For the sector erase command (see Section 2.4.1.3.4, “Sector Erase Command”), the contents
of the data buffer are ignored and address bits [9:0] contained in the address buffer are ignored.
e) For the mass erase command (see Section 2.4.1.3.5, “Mass Erase Command”), the contents of
the data buffer and address buffer are ignored.
f) For the sector erase abort command (see Section 2.4.1.3.6, “Sector Erase Abort Command”),
the contents of the data buffer and address buffer are ignored.
3. Clear the CBEIF flag by writing a 1 to CBEIF to launch the command. When the CBEIF flag is
cleared, the CCIF flag is cleared on the same bus cycle by internal hardware indicating that the
command was successfully launched. For all command write sequences except data compress and
sector erase abort, the CBEIF flag will set four bus cycles after the CCIF flag is cleared indicating
that the address, data, and command buffers are ready for a new command write sequence to begin.
For data compress and sector erase abort operations, the CBEIF flag will remain clear until the
operation completes.
A command write sequence can be aborted prior to clearing the CBEIF flag by writing a 0 to the CBEIF
flag and will result in the ACCERR flag being set.
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 99
Except for the sector erase abort command, a buffered command will wait for the active operation to be
completed before being launched. The sector erase abort command is launched when the CBEIF flag is
cleared as part of a sector erase abort command write sequence. After a command is launched, the
completion of the command operation is indicated by the setting of the CCIF flag. The CCIF flag only sets
when all active and buffered commands have been completed.
2.4.1.3 Valid Flash Commands
Table 2-20 summarizes the valid Flash commands along with the effects of the commands on the Flash
block.
CAUTION
A Flash word must be in the erased state before being programmed.
Cumulative programming of bits within a Flash word is not allowed and will
result in invalid data stored.
Table 2-20. Valid Flash Command Description
FCMDB NVM
Command Function on Flash Memory
0x05 Erase
Verify Verify all memory bytes in the Flash block are erased. If the Flash block is erased, the BLANK
flag in the FSTAT register will set upon command completion.
0x06 Data
Compress Compress data from a selected portion of the Flash block. The resulting signature is stored in
the FDATA register.
0x20 Program Program a word (two bytes) in the Flash block.
0x40 Sector
Erase Erase all memory bytes in a sector of the Flash block.
0x41 Mass
Erase Erase all memory bytes in the Flash block. A mass erase of the full Flash block is only possible
when FPLDIS, FPHDIS, and FPOPEN bits in the FPROT register are set prior to launching the
command.
0x47 Sector
Erase
Abort
Abort the sector erase operation. The sector erase operation will terminate according to a set
procedure. The Flash sector must not be considered erased if the ACCERR flag is set upon
command completion.
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
100 Freescale Semiconductor
2.4.1.3.1 Erase Verify Command
The erase verify operation is used to confirm that a Flash block is erased. After launching the erase verify
command, the CCIF flag in the FSTAT register will set after the operation has completed unless a second
command has been buffered. The number of bus cycles required to execute the erase verify operation is
equal to the number of addresses in the Flash block plus 12 bus cycles as measured from the time the
CBEIF flag is cleared until the CCIF flag is set. The result of the erase verify operation is reflected in the
state of the BLANK flag in the FSTAT register. If the BLANK flag is set in the FSTAT register, the Flash
memory is erased.
If the ECC logic detects a double bit fault during the erase verify operation, the operation will terminate
immediately and set the DFDIF and ACCERR flags in the FSTAT register. The faulty address will be
stored in the FADDR registers and the ECC parity bits read at the faulty address will be stored in the
FDATALO register. The CCIF flag will set after the DFDIF flag is set and the faulty information is stored
in the FADDR and FDATALO registers.
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 101
Figure 2-24. Example Erase Verify Command Flow
Write: Register FCLKDIV
Read: Register FCLKDIV
Bit FDIVLD set?
Write: Flash Block Address
Write: Register FCMD
Erase Verify Command 0x05
Write: Register FSTAT
yes
no
Clear bit CBEIF 0x80
Clock Register
Loaded
Check
1.
2.
3.
Clear bit ACCERR 0x10
Write: Register FSTAT
yes
Access
Error Check
Read: Register FSTAT
no
no
and Dummy Data
Bit Polling for
Command
Completion Check Read: Register FSTAT
NOTE: command write sequence
aborted by writing 0x00 to
FSTAT register.
NOTE: command write sequence
aborted by writing 0x00 to
FSTAT register.
CCIF
Set?
Bit
ACCERR
Set?
Bit
EXIT
yes
BLANK
Set?
Bit
yes
no
yes
Double Bit
Fault Detection
Check no
DFDIF
Set?
Bit
Clear bit DFDIF 0x08
Write: Register FSTAT
Mass Erase Flash Block
yes
no
DFDIF
Set?
Bit
Flash Block not erased
Blank
Status Check
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
102 Freescale Semiconductor
2.4.1.3.2 Data Compress Command
The data compress command is used to check Flash code integrity by compressing data from a selected
portion of the Flash block into a signature analyzer. The starting address for the data compress operation
is defined by the address written during the command write sequence. The number of consecutive word
addresses compressed is defined by the data written during the command write sequence. The number of
words that can be compressed in a single data compress operation ranges from 1 to 16,384. After launching
the data compress command, the CCIF flag in the FSTAT register will set after the data compress
operation has completed. The number of bus cycles required to execute the data compress operation is
equal to two times the number of addresses read plus 20 bus cycles as measured from the time the CBEIF
flag is cleared until the CCIF flag is set. After the CCIF flag is set, the signature generated by the data
compress operation is available in the FDATA register. The signature in the FDATA register can be
compared to the expected signature to determine the integrity of the selected data stored in the Flash block.
If the last address of the Flash block is reached during the data compress operation, data compression will
continue with the starting address of the Flash block.
NOTE
Since the FDATA register (or data buffer) is written to as part of the data
compress operation, a command write sequence is not allowed to be
buffered behind a data compress command write sequence. The CBEIF flag
will not set after launching the data compress command to indicate that a
command must not be buffered behind it. If an attempt is made to start a new
command write sequence with a data compress operation active, the
ACCERR flag in the FSTAT register will be set. A new command write
sequence must only be started after reading the signature stored in the
FDATA register. A Flash array read that generates a double bit fault will
overwrite the contents of the FDATA register.
In order to take corrective action, it is recommended that the data compress command be executed on a
Flash sector or subset of a Flash sector. If the data compress operation on a Flash sector returns an invalid
signature, the Flash sector should be erased using the sector erase command and then reprogrammed using
the program command.
NOTE
During the data compress operation, the Flash array is read with a
sense-amp margin setting that is different from the normal array read
setting. Therefore, if the data compress operation returns an invalid
signature, the section of the Flash array compressed may still be functional.
The failing section of the Flash array could be validated using normal array
read operations.
The data compress command can be used to verify that a sector or sequential set of sectors are erased.
If the ECC logic detects a double bit fault during the data compress operation, the operation will terminate
immediately and set the DFDIF and ACCERR flags in the FSTAT register. The faulty address will be
stored in the FADDR registers and the ECC parity bits read at the faulty address will be stored in the
FDATALO register. The CCIF flag will set after the DFDIF flag is set and the faulty information is stored
in the FADDR and FDATALO registers.
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 103
Figure 2-25. Example Data Compress Command Flow
Write: Register FCLKDIV
Read: Register FCLKDIV
Bit FDIVLD set?
Write: Flash address to start
Write: Register FCMD
Data Compress Command 0x06
Write: Register FSTAT
yes
no
Clear bit CBEIF 0x80
Clock Register
Loaded
Check
1.
2.
3.
Read: Register FSTAT
no
EXIT
compression and number of
Bit Polling for
Command
Completion Check Read: Register FSTAT
yes
NOTE: command write sequence
aborted by writing 0x00 to
FSTAT register.
NOTE: command write sequence
aborted by writing 0x00 to
FSTAT register.
CCIF
Set?
Bit
word addresses to compress (max 16,384)
Read: Register FDATA
Data Compress Signature
no Erase and Reprogram
yes
Signature
Valid?
Signature Flash Region Compressed
Compared to
Known Value
yes
Double Bit
Fault Detection
Check
no
DFDIF
Set?
Bit
Clear bit ACCERR 0x10
Write: Register FSTAT
yes
Access
Error Check ACCERR
Set?
Bit yes
no
DFDIF
Set?
Bit
Clear bit DFDIF 0x08
Write: Register FSTAT
no
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
104 Freescale Semiconductor
Data Compress Operation
The Flash module contains a 16-bit multiple-input signature register (MISR) to generate a 16-bit signature
based on selected Flash array data. The final signature, which is stored in the FDATA register, is based on
the following logic equation which is executed on every data compression cycle during the operation:
MISR[15:0] = {MISR[14:0], ^MISR[15,4,2,1]} ^ DATA[15:0] Eqn. 2-1
where MISR is the content of the internal signature register and DATA is the data to be compressed as
shown in Figure 2-26.
Figure 2-26. 16-Bit MISR Diagram
During the data compress operation, the following steps are executed:
1. MISR is reset to 0xFFFF.
2. DATA from the selected Flash array data range is read and compressed into the MISR with address
incrementing.
3. DATA from the selected Flash array data range is read and compressed into the MISR with address
decrementing.
4. The contents of the MISR are written to the FDATA register.
DQ
>
+
+
= Exclusive-OR
DATA[0]
M0 DQ
>
+
DATA[1]
M1 DQ
>
+
DATA[2]
M2 DQ
>
+
DATA[3]
M3 DQ
>
+
DATA[4]
M4 DQ
>
+
DATA[5]
M5 DQ
>
+
DATA[15]
M15
...
+ +
+
MISR[15:0] = Q[15:0]
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 105
2.4.1.3.3 Program Command
The program command is used to program a previously erased word in the Flash memory using an
embedded algorithm. If the word to be programmed is in a protected area of the Flash block, the PVIOL
flag in the FSTAT register will set and the program command will not launch. After the program command
has successfully launched, the CCIF flag in the FSTAT register will set after the program operation has
completed unless a second command has been buffered.
A summary of the launching of a program operation is shown in Figure 2-27.
Figure 2-27. Example Program Command Flow
Write: Register FCLKDIV
Read: Register FCLKDIV
Bit FDIVLD set?
Write: Flash Address and
Write: Register FCMD
Program Command 0x20
Write: Register FSTAT
yes
no
Clear bit CBEIF 0x80
yes
Clock Register
Loaded
Check
1.
2.
3.
Clear bit ACCERR 0x10
Write: Register FSTAT
no
yes
no
Protection
Violation Check
Access
Error Check
Read: Register FSTAT
no
no
Address, Data,
Command
Buffer Empty Check Next Write?
yes
EXIT
no
Program Data
Clear bit PVIOL 0x20
Write: Register FSTAT
yes
Bit Polling for
Command
Completion Check Read: Register FSTAT
yes
NOTE: command write sequence
aborted by writing 0x00 to
FSTAT register.
NOTE: command write sequence
aborted by writing 0x00 to
FSTAT register.
CCIF
Set?
Bit
CBEIF
Set?
Bit
ACCERR
Set?
Bit
PVIOL
Set?
Bit
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
106 Freescale Semiconductor
2.4.1.3.4 Sector Erase Command
The sector erase command is used to erase the addressed sector in the Flash memory using an embedded
algorithm. If the Flash sector to be erased is in a protected area of the Flash block, the PVIOL flag in the
FSTAT register will set and the sector erase command will not launch. After the sector erase command
has successfully launched, the CCIF flag in the FSTAT register will set after the sector erase operation has
completed unless a second command has been buffered.
Figure 2-28. Example Sector Erase Command Flow
Write: Register FCLKDIV
Read: Register FCLKDIV
Bit FDIVLD set?
Write: Flash Sector Address
Write: Register FCMD
Sector Erase Command 0x40
Write: Register FSTAT
yes
no
Clear bit CBEIF 0x80
yes
Clock Register
Loaded
Check
1.
2.
3.
Clear bit ACCERR 0x10
Write: Register FSTAT
no
yes
no
Protection
Violation Check
Access
Error Check
Read: Register FSTAT
no
no
Address, Data,
Command
Buffer Empty Check Next Write?
yes
EXIT
no
and Dummy Data
Clear bit PVIOL 0x20
Write: Register FSTAT
yes
Bit Polling for
Command
Completion Check Read: Register FSTAT
yes
NOTE: command write sequence
aborted by writing 0x00 to
FSTAT register.
NOTE: command write sequence
aborted by writing 0x00 to
FSTAT register.
CCIF
Set?
Bit
PVIOL
Set?
Bit
ACCERR
Set?
Bit
CBEIF
Set?
Bit
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 107
2.4.1.3.5 Mass Erase Command
The mass erase command is used to erase a Flash memory block using an embedded algorithm. If the Flash
block to be erased contains any protected area, the PVIOL flag in the FSTAT register will set and the mass
erase command will not launch. After the mass erase command has successfully launched, the CCIF flag
in the FSTAT register will set after the mass erase operation has completed unless a second command has
been buffered.
Figure 2-29. Example Mass Erase Command Flow
Write: Register FCLKDIV
Read: Register FCLKDIV
Bit FDIVLD set?
Write: Flash Block Address
Write: Register FCMD
Mass Erase Command 0x41
Write: Register FSTAT
yes
no
Clear bit CBEIF 0x80
yes
Clock Register
Loaded
Check
1.
2.
3.
Clear bit ACCERR 0x10
Write: Register FSTAT
no
yes
no
Protection
Violation Check
Access
Error Check
Read: Register FSTAT
CCIF
Set?
Bit no
no
Address, Data,
Command
Buffer Empty Check Next Write?
yes
EXIT
no
and Dummy Data
Clear bit PVIOL 0x20
Write: Register FSTAT
yes
Bit Polling for
Command
Completion Check Read: Register FSTAT
yes
NOTE: command write sequence
aborted by writing 0x00 to
FSTAT register.
NOTE: command write sequence
aborted by writing 0x00 to
FSTAT register.
PVIOL
Set?
Bit
ACCERR
Set?
Bit
CBEIF
Set?
Bit
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
108 Freescale Semiconductor
2.4.1.3.6 Sector Erase Abort Command
The sector erase abort command is used to terminate the sector erase operation so that other sectors in the
Flash block are available for read and program operations without waiting for the sector erase operation
to complete. If the sector erase abort command is launched resulting in the early termination of an active
sector erase operation, the ACCERR flag will set after the operation completes as indicated by the CCIF
flag being set. The ACCERR flag sets to inform the user that the sector may not be fully erased and a new
sector erase command must be launched before programming any location in that specific sector. If the
sector erase abort command is launched but the active sector erase operation completes normally, the
ACCERR flag will not set upon completion of the operation as indicated by the CCIF flag being set.
Therefore, if the ACCERR flag is not set after the sector erase abort command has completed, the sector
being erased when the abort command was launched is fully erased. The maximum number of cycles
required to abort a sector erase operation is equal to four FCLK periods (see Section 2.4.1.1, “Writing the
FCLKDIV Register”) plus five bus cycles as measured from the time the CBEIF flag is cleared until the
CCIF flag is set.
NOTE
Since the ACCERR bit in the FSTAT register may be set at the completion
of the sector erase abort operation, a command write sequence is not
allowed to be buffered behind a sector erase abort command write sequence.
The CBEIF flag will not set after launching the sector erase abort command
to indicate that a command must not be buffered behind it. If an attempt is
made to start a new command write sequence with a sector erase abort
operation active, the ACCERR flag in the FSTAT register will be set. A new
command write sequence may be started after clearing the ACCERR flag, if
set.
NOTE
The sector erase abort command must be used sparingly because a sector
erase operation that is aborted counts as a complete program/erase cycle.
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 109
Figure 2-30. Example Sector Erase Abort Command Flow
Write: Dummy Flash Address
Write: Register FCMD
Sector Erase Abort Cmd 0x47
Write: Register FSTAT
Clear bit CBEIF 0x80
1.
2.
3.
Read: Register FSTAT
no
EXIT
and Dummy Data
Bit Polling for
Command
Completion Check Read: Register FSTAT
yes
NOTE: command write sequence
aborted by writing 0x00 to
FSTAT register.
NOTE: command write sequence
aborted by writing 0x00 to
FSTAT register.
CCIF
Set?
Bit
Execute Sector Erase Command Flow
no
Bit Polling for
Command
Completion Check Read: Register FSTAT
yes
CCIF
Set?
Bit no
yes
Abort
Needed?
Erase
EXIT
Clear bit ACCERR 0x10
Write: Register FSTAT
yes
no
Access
Error Check ACCERR
Set?
Bit
EXIT
Sector Erase
Completed Sector Erase
Aborted
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
110 Freescale Semiconductor
2.4.1.4 Illegal Flash Operations
The ACCERR flag will be set during the command write sequence if any of the following illegal steps are
performed, causing the command write sequence to immediately abort:
1. Writing to a Flash address before initializing the FCLKDIV register.
2. Writing a byte or misaligned word to a valid Flash address.
3. Starting a command write sequence while a data compress operation is active.
4. Starting a command write sequence while a sector erase abort operation is active.
5. Writing a second word to a Flash address in the same command write sequence.
6. Writing to any Flash register other than FCMD after writing a word to a Flash address.
7. Writing a second command to the FCMD register in the same command write sequence.
8. Writing an invalid command to the FCMD register.
9. When security is enabled, writing a command other than mass erase to the FCMD register when
the write originates from a non-secure memory location or from the Background Debug Mode.
10. Writing to any Flash register other than FSTAT (to clear CBEIF) after writing to the FCMD
register.
11. Writing a 0 to the CBEIF flag in the FSTAT register to abort a command write sequence.
The ACCERR flag will not be set if any Flash register is read during a valid command write sequence.
The ACCERR flag will also be set if any of the following events occur:
1. Launching the sector erase abort command while a sector erase operation is active which results in
the early termination of the sector erase operation (see Section 2.4.1.3.6, “Sector Erase Abort
Command”)
2. A double bit fault is detected in any of the following Flash operations:
a) Array read
b) Erase Verify
c) Data Compress
d) Reset Sequence Array Read (Configuration Field)
3. The MCU enters stop mode and a program or erase operation is in progress. The operation is
aborted immediately and any pending command is purged (see Section 2.5.2, “Stop Mode”).
If the Flash memory is read during execution of an algorithm (i.e., CCIF flag in the FSTAT register is low),
the read operation will return invalid data and the ACCERR flag will not be set.
If the ACCERR flag is set in the FSTAT register, the user must clear the ACCERR flag before starting
another command write sequence (see Section 2.3.2.7, “Flash Status Register (FSTAT)”).
The PVIOL flag will be set after the command is written to the FCMD register during a command write
sequence if any of the following illegal operations are attempted, causing the command write sequence to
immediately abort:
1. Writing the program command if the address written in the command write sequence was in a
protected area of the Flash memory.
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 111
2. Writing the sector erase command if the address written in the command write sequence was in a
protected area of the Flash memory.
3. Writing the mass erase command while any Flash protection is enabled.
If the PVIOL flag is set in the FSTAT register, the user must clear the PVIOL flag before starting another
command write sequence (see Section 2.3.2.7, “Flash Status Register (FSTAT)”).
2.5 Operating Modes
2.5.1 Wait Mode
If a command is active (CCIF = 0) when the MCU enters wait mode, the active command and any buffered
command will be completed.
The Flash module can recover the MCU from wait mode if the CBEIF and CCIF interrupts are enabled
(Section 2.8, “Interrupts”).
2.5.2 Stop Mode
If a command is active (CCIF = 0) when the MCU enters stop mode, the operation will be aborted and, if
the operation is program or erase, the Flash array data being programmed or erased may be corrupted and
the CCIF and ACCERR flags will be set. If active, the high voltage circuitry to the Flash memory will
immediately be switched off when entering stop mode. Upon exit from stop mode, the CBEIF flag is set
and any buffered command will not be launched. The ACCERR flag must be cleared before starting a
command write sequence (see Section 2.4.1.2, “Command Write Sequence”).
NOTE
As active commands are immediately aborted when the MCU enters stop
mode, it is strongly recommended that the user does not use the STOP
instruction during program or erase operations.
2.5.3 Background Debug Mode
In background debug mode (BDM), the FPROT register is writable. If the MCU is unsecured, then all
Flash commands listed in Table 2-20 can be executed.
2.6 Flash Module Security
The Flash module provides the necessary security information to the MCU. After each reset, the Flash
module determines the security state of the MCU as defined in Section 2.3.2.2, “Flash Security Register
(FSEC)”.
The contents of the Flash security byte at 0xFF0F in the Flash configuration field must be changed directly
by programming 0xFF0F when the MCU is unsecured and the higher address sector is unprotected. If the
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
112 Freescale Semiconductor
Flash security byte remains in a secured state, any reset will cause the MCU to initialize to a secure
operating mode.
2.6.1 Unsecuring the MCU using Backdoor Key Access
The MCU may be unsecured by using the backdoor key access feature which requires knowledge of the
contents of the backdoor keys (four 16-bit words programmed at addresses 0xFF00–0xFF07). If the
KEYEN[1:0] bits are in the enabled state (see Section 2.3.2.2, “Flash Security Register (FSEC)”) and the
KEYACC bit is set, a write to a backdoor key address in the Flash memory triggers a comparison between
the written data and the backdoor key data stored in the Flash memory. If all four words of data are written
to the correct addresses in the correct order and the data matches the backdoor keys stored in the Flash
memory, the MCU will be unsecured. The data must be written to the backdoor keys sequentially starting
with 0xFF00–0xFF01 and ending with 0xFF06–0xFF07. 0x0000 and 0xFFFF are not permitted as
backdoor keys. While the KEYACC bit is set, reads of the Flash memory will return invalid data.
The user code stored in the Flash memory must have a method of receiving the backdoor key from an
external stimulus. This external stimulus would typically be through one of the on-chip serial ports.
If the KEYEN[1:0] bits are in the enabled state (see Section 2.3.2.2, “Flash Security Register (FSEC)”),
the MCU can be unsecured by the backdoor access sequence described below:
1. Set the KEYACC bit in the Flash configuration register (FCNFG).
2. Write the correct four 16-bit words to Flash addresses 0xFF00–0xFF07 sequentially starting with
0xFF00.
3. Clear the KEYACC bit.
4. If all four 16-bit words match the backdoor keys stored in Flash addresses 0xFF00–0xFF07, the
MCU is unsecured and the SEC[1:0] bits in the FSEC register are forced to the unsecure state of
1:0.
The backdoor key access sequence is monitored by an internal security state machine. An illegal operation
during the backdoor key access sequence will cause the security state machine to lock, leaving the MCU
in the secured state. A reset of the MCU will cause the security state machine to exit the lock state and
allow a new backdoor key access sequence to be attempted. The following operations during the backdoor
key access sequence will lock the security state machine:
1. If any of the four 16-bit words does not match the backdoor keys programmed in the Flash array.
Double bit faults detected while reading the backdoor keys from the Flash array are ignored.
2. If the four 16-bit words are written in the wrong sequence.
3. If more than four 16-bit words are written.
4. If any of the four 16-bit words written are 0x0000 or 0xFFFF.
5. If the KEYACC bit does not remain set while the four 16-bit words are written.
6. If any two of the four 16-bit words are written on successive MCU clock cycles.
After the backdoor keys have been correctly matched, the MCU will be unsecured. After the MCU is
unsecured, the Flash security byte can be programmed to the unsecure state, if desired.
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 113
In the unsecure state, the user has full control of the contents of the backdoor keys by programming
addresses 0xFF00–0xFF07 in the Flash configuration field.
The security as defined in the Flash security byte (0xFF0F) is not changed by using the backdoor key
access sequence to unsecure. The backdoor keys stored in addresses 0xFF00–0xFF07 are unaffected by
the backdoor key access sequence. After the next reset of the MCU, the security state of the Flash module
is determined by the Flash security byte (0xFF0F). The backdoor key access sequence has no effect on the
program and erase protections defined in the Flash protection register.
It is not possible to unsecure the MCU in special single-chip mode by using the backdoor key access
sequence via the background debug mode (BDM).
2.6.2 Unsecuring the Flash Module in Special Single-Chip Mode using
BDM
The MCU can be unsecured in special single-chip mode by erasing the Flash module by the following
method :
Reset the MCU into special single-chip mode, delay while the erase test is performed by the BDM
secure ROM, send BDM commands to disable protection in the Flash module, and execute a mass
erase command write sequence to erase the Flash memory.
After the CCIF flag sets to indicate that the mass operation has completed, reset the MCU into special
single-chip mode. The BDM secure ROM will verify that the Flash memory is erased and will assert the
UNSEC bit in the BDM status register. This BDM action will cause the MCU to override the Flash security
state and the MCU will be unsecured. All BDM commands will be enabled and the Flash security byte
may be programmed to the unsecure state by the following method:
Send BDM commands to execute a word program sequence to program the Flash security byte to
the unsecured state and reset the MCU.
2.7 Resets
2.7.1 Flash Reset Sequence
On each reset, the Flash module executes a reset sequence to hold CPU activity while loading the following
registers from the Flash memory according to Table 2-2:
FPROT — Flash Protection Register (see Section 2.3.2.5).
If a double bit fault is detected during the read of the protection field as part of the reset sequence,
the FPOPEN bit in the FPROT register will be clear and remaining bits will be set leaving the Flash
block fully protected from program and erase.
FSEC — Flash Security Register (see Section 2.3.2.2).
If a double bit fault is detected during the read of the security field as part of the reset sequence, all
bits in the FSEC register will be set leaving the Flash module in a secure state with Backdoor Key
Access disabled.
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
114 Freescale Semiconductor
If a double bit fault is detected during array reads as part of the reset sequence, the ACCERR flag will set
in the FSTAT register.
2.7.2 Reset While Flash Command Active
If a reset occurs while any Flash command is in progress, that command will be immediately aborted. The
state of the word being programmed or the sector / block being erased is not guaranteed.
2.8 Interrupts
The Flash module can generate an interrupt when all Flash command operations have completed, when the
Flash address, data, and command buffers are empty, or when a Flash array read or operation has detected
a double bit fault.
NOTE
Vector addresses and their relative interrupt priority are determined at the
MCU level.
2.8.1 Description of Flash Interrupt Operation
The logic used for generating interrupts is shown in Figure 2-31.
The Flash module uses the CBEIF and CCIF flags in combination with the CBIE and CCIE enable bits to
generate the Flash command interrupt request. The Flash module uses the DFDIF flag in combination with
the DFDIE enable bit to generate the Flash double fault detect interrupt request.
Table 2-21. Flash Interrupt Sources
Interrupt Source Interrupt Flag Local Enable Global(CCR)
Mask
Flash Address, Data and Command
Buffers empty CBEIF
(FSTAT register) CBEIE
(FCNFG register) I-Bit
All Flash commands completed CCIF
(FSTAT register) CCIE
(FCNFG register) I-Bit
Flash array read or verify operation
detected a double bit fault DFDIF
(FSTAT register) DFDIE
(FCNFG register) I-Bit
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 115
Figure 2-31. Flash Interrupt Implementation
For a detailed description of the register bits, refer to Section 2.3.2.4, “Flash Configuration Register
(FCNFG)” and Section 2.3.2.7, “Flash Status Register (FSTAT)”.
Flash Command Interrupt Request
CBEIE
CBEIF
CCIE
CCIF
DFDIE
DFDIF Flash Double Fault Detect Interrupt Request
Chapter 2 128 Kbyte ECC Flash Module (S12FTS128K1ECCV1)
MC9S12KG128 Data Sheet, Rev. 1.16
116 Freescale Semiconductor
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 117
Chapter 3
2 Kbyte EEPROM Module (S12EETS2KV1)
3.1 Introduction
This document describes the EETS2K module which is a 2 Kbyte EEPROM (nonvolatile) memory. The
EETS2K block uses a small sector Flash memory to emulate EEPROM functionality. It is an array of
electrically erasable and programmable, nonvolatile memory. The EEPROM memory is organized as 1024
rows of 2 bytes (1 word). The EEPROM memory’s erase sector size is 2 rows or 2 words (4 bytes).
The EEPROM memory may be read as either bytes, aligned words, or misaligned words. Read access time
is one bus cycle for byte and aligned word, and two bus cycles for misaligned words.
Program and erase functions are controlled by a command driven interface. Both sector erase and mass
erase of the entire EEPROM memory are supported. An erased bit reads 1 and a programmed bit reads 0.
The high voltage required to program and erase is generated internally by on-chip charge pumps.
It is not possible to read from the EEPROM memory while it is being erased or programmed.
The EEPROM memory is ideal for data storage for single-supply applications allowing for field
reprogramming without requiring external programming voltage sources.
CAUTION
An EEPROM word must be in the erased state before being programmed.
Cumulative programming of bits within a word is not allowed.
3.1.1 Glossary
Command Write Sequence A three-step MCU instruction sequence to program, erase, or erase verify
the EEPROM.
3.1.2 Features
2 Kbytes of EEPROM memory
Minimum erase sector of 4 bytes
Automated program and erase algorithms
Interrupts on EEPROM command completion and command buffer empty
Fast sector erase and word program operation
2-stage command pipeline
Flexible protection scheme for protection against accidental program or erase
Single power supply program and erase
Chapter 3 2 Kbyte EEPROM Module (S12EETS2KV1)
MC9S12KG128 Data Sheet, Rev. 1.16
118 Freescale Semiconductor
3.1.3 Modes of Operation
Program and erase operation (please refer to Section 3.4.1 for details).
3.1.4 Block Diagram
Figure 3-1 shows a block diagram of the EETS2K module.
Figure 3-1. EETS2K Block Diagram
3.2 External Signal Description
The EETS2K module contains no signals that connect off chip.
3.3 Memory Map and Register Definition
This section describes the EETS2K memory map and registers.
3.3.1 Module Memory Map
Figure 3-2 shows the EETS2K memory map. Location of the EEPROM array in the MCU memory map
is defined in the Device Overview chapter and is reflected in the INITEE register contents defined in the
INT block description chapter. Shown within the EEPROM array are: a protection/reserved field and
user-defined EEPROM protected sectors. The 16-byte protection/reserved field is located in the EEPROM
array from address 0x07F0 to 0x07FF. A description of this protection/reserved field is given in Table 3-1.
EETS2K
EEPROM Array
1024 * 16 Bits
row0
row1
row1023
Oscillator Clock
Divider
Clock
Command
Interface
Command Pipeline
comm2
Registers
EECLK
addr2
data2
comm1
addr1
data1
Command
Complete
Interrupt
Command
Buffer Empty
Interrupt
Chapter 3 2 Kbyte EEPROM Module (S12EETS2KV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 119
The EEPROM module has hardware interlocks which protect data from accidental corruption. A protected
sector is located at the higher address end of the EEPROM array, just below address 0x07FF. The protected
sector in the EEPROM array can be sized from 64 bytes to 512 bytes. In addition, the EPOPEN bit in the
EPROT register, described in Section 3.3.2.5, “EEPROM Protection Register (EPROT)”, can be set to
globally protect the entire EEPROM array.
Chip security is defined at the MCU level.
Figure 3-2. EEPROM Memory Map
Table 3-1. EEPROM Protection/Reserved Field
Address Offset Size
(Bytes) Description
0x07F0 – 0x07FC 13 Reserved
0x07FD 1 EEPROM protection byte
0x07FE – 0x07FF 2 Reserved
EEPROM Registers
MODULE BASE + 0x0000
EEPROM BASE + 0x07FF
0x07C0
0x07F0 – 0x07FF, EEPROM Protection/Reserved Field
MODULE BASE + 0x000B
0x0780
0x0600
(12 BYTES)
0x0700 EEPROM Protected High Sectors
64, 128, 192, 256, 320, 384, 448, 512 bytes
EEPROM BASE + 0x0000
1536 BYTES
0x0740
0x06C0
0x0640
0x0680
EEPROM ARRAY
Chapter 3 2 Kbyte EEPROM Module (S12EETS2KV1)
MC9S12KG128 Data Sheet, Rev. 1.16
120 Freescale Semiconductor
The EEPROM module also contains a set of 12 control and status registers located in address space module
base + 0x0000 to module base + 0x000B.
Table 3-2 gives an overview of all EETS2K registers.
Table 3-2. EEPROM Register Map
Module
Base + Register Name Normal Mode
Access
0x0000 EEPROM Clock Divider Register (ECLKDIV) R/W
0x0001 RESERVED11
1Intended for factory test purposes only.
R
0x0002 RESERVED21R
0x0003 EEPROM Configuration Register (ECNFG) R/W
0x0004 EEPROM Protection Register (EPROT) R/W
0x0005 EEPROM Status Register (ESTAT) R/W
0x0006 EEPROM Command Register (ECMD) R/W
0x0007 RESERVED31R
0x0008 EEPROM High Address Register (EADDRHI) R/W
0x0009 EEPROM Low Address Register (EADDRLO) R/W
0x000A EEPROM High Data Register (EDATAHI) R/W
0x000B EEPROM Low Data Register (EDATALO) R/W
Chapter 3 2 Kbyte EEPROM Module (S12EETS2KV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 121
3.3.2 Register Descriptions
3.3.2.1 EEPROM Clock Divider Register (ECLKDIV)
The ECLKDIV register is used to control timed events in program and erase algorithms.
Register
Name Bit 7 654321Bit 0
0x0000
ECLKDIV R EDIVLD PRDIV8 EDIV5 EDIV4 EDIV3 EDIV2 EDIV1 EDIV0
W
0x0001
RESERVED1 R00000000
W
0x0002
RESERVED2 R00000000
W
0x0003
ECNFG RCBEIE CCIE 000000
W
0x0004
EPROT REPOPEN NV6 NV5 NV4 EPDIS EP2 EP1 EPO
W
0x0005
ESTAT RCBEIF CCIF PVIOL ACCERR 0 BLANK 0 0
W
0x0006
ECMD R0 CMDB6 CMDB5 00
CMDB2 0CMDB0
W
0x0007
RESERVED3 R00000000
W
0x0008
EADDRHI R000000 EABHI
W
0x0009
EADDRLO REABLO
W
0x000A
EDATAHI REDHI
W
0x000B
EDATALO REDLO
W
= Unimplemented or Reserved
Figure 3-3. EETS2K Register Summary
Chapter 3 2 Kbyte EEPROM Module (S12EETS2KV1)
MC9S12KG128 Data Sheet, Rev. 1.16
122 Freescale Semiconductor
All bits in the ECLKDIV register are readable while bits 6-0 are write once and bit 7 is not writable.
3.3.2.2 RESERVED1
This register is reserved for factory testing and is not accessible to the user.
All bits read 0 and are not writable.
3.3.2.3 RESERVED2
This register is reserved for factory testing and is not accessible to the user.
Module Base + 0x0000
76543210
R EDIVLD PRDIV8 EDIV5 EDIV4 EDIV3 EDIV2 EDIV1 EDIV0
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 3-4. EEPROM Clock Divider Register (ECLKDIV)
Table 3-3. ECLKDIV Field Descriptions
Field Description
7
EDIVLD Clock Divider Loaded
0 Register has not been written.
1 Register has been written to since the last reset.
6
PRDIV8 Enable Prescaler by 8
0 The oscillator clock is directly fed into the ECLKDIV divider.
1 The oscillator clock is divided by 8 before feeding into the clock divider.
5:0
EDIV[5:0] Clock Divider Bits — The combination of PRDIV8 and EDIV[5:0] must divide the oscillator clock down to a
frequency of 150 kHz 200 kHz. The maximum divide ratio is 512. Please refer to Section 3.4.1.1, “Writing the
ECLKDIV Register” for more information.
Module Base + 0x0001
76543210
R00000000
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 3-5. RESERVED1
Chapter 3 2 Kbyte EEPROM Module (S12EETS2KV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 123
All bits read 0 and are not writable.
3.3.2.4 EEPROM Configuration Register (ECNFG)
The ECNFG register enables the EEPROM interrupts.
CBEIE and CCIE bits are readable and writable while bits 5-0 read 0 and are not writable.
3.3.2.5 EEPROM Protection Register (EPROT)
The EPROT register defines which EEPROM sectors are protected against program or erase.
Module Base + 0x0002
76543210
R00000000
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 3-6. RESERVED2
Module Base + 0x0003
76543210
RCBEIE CCIE 000000
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 3-7. EEPROM Configuration Register (ECNFG)
Table 3-4. ECNFG Field Descriptions
Field Description
7
CBEIE Command Buffer Empty Interrupt Enable — The CBEIE bit enables the interrupts in case of an empty
command buffer in the EEPROM.
0 Command buffer empty interrupts disabled.
1 An interrupt will be requested whenever the CBEIF flag is set (see Section 3.3.2.6, “EEPROM Status Register
(ESTAT)”).
6
CCIE Command Complete Interrupt Enable — The CCIE bit enables the interrupts in case of all commands being
completed in the EEPROM.
0 Command complete interrupts disabled.
1 An interrupt will be requested whenever the CCIF flag is set (see Section 3.3.2.6, “EEPROM Status Register
(ESTAT)”).
Chapter 3 2 Kbyte EEPROM Module (S12EETS2KV1)
MC9S12KG128 Data Sheet, Rev. 1.16
124 Freescale Semiconductor
The EPROT register is loaded from EEPROM array address 0x07FD during reset, as indicated by the F in
Figure 3-8.
All bits in the EPROT register are readable. Bits NV[6:4] are not writable. The EPOPEN and EPDIS bits
in the EPROT register can only be written to the protected state (i.e., 0). The EP[2:0] bits can be written
anytime until bit EPDIS is cleared. If the EPOPEN bit is cleared, then the state of the EPDIS and EP[2:0]
bits is irrelevant.
To change the EEPROM protection that will be loaded on reset, the upper sector of EEPROM must first
be unprotected, then the EEPROM protect byte located at address 0x07FD must be written to.
A protected EEPROM sector is disabled by the EPDIS bit while the size of the protected sector is defined
by the EP bits in the EPROT register.
Trying to alter any of the protected areas will result in a protect violation error and PVIOL flag will be set
in the ESTAT register. A mass erase of a whole EEPROM block is only possible when protection is fully
disabled by setting the EPOPEN and EPDIS bits. An attempt to mass erase an EEPROM block while
protection is enabled will set the PVIOL flag in the ESTAT register.
Module Base + 0x0004
76543210
REPOPEN NV6 NV5 NV4 EPDIS EP2 EP1 EP0
W
Reset F FFFFFFF
= Unimplemented or Reserved
Figure 3-8. EEPROM Protection Register (EPROT)
Table 3-5. EPROT Field Descriptions
Field Description
7
EPOPEN Opens EEPROM for Program or Erase
0 The whole EEPROM array is protected. In this case, the EPDIS and EP bits within the protection register are
ignored.
1 The EEPROM sectors not protected are enabled for program or erase.
6:4
NV[6:4] Nonvolatile Flag Bits — These three bits are available to the user as nonvolatile flags.
3
EPDIS EEPROM Protection Address Range Disable The EPDIS bit determines whether there is a protected area
in the space of the EEPROM address map.
0 Protection enabled
1 Protection disabled
2:0
EP[2:0] EEPROM Protection Address Size — The EP[2:0] bits determine the size of the protected sector. Refer to
Table 3-6.
Chapter 3 2 Kbyte EEPROM Module (S12EETS2KV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 125
3.3.2.6 EEPROM Status Register (ESTAT)
The ESTAT register defines the EEPROM state machine command status and EEPROM array access,
protection and erase verify status.
CBEIF, PVIOL, and ACCERR bits are readable and writable, CCIF and BLANK bits are readable but not
writable, remaining bits read 0 and are not writable in normal mode. FAIL is readable and writable in
special mode. FAIL must be clear when starting a command write sequence. DONE is readable but not
writable in special mode.
Table 3-6. EEPROM Address Range Protection
EP[2:0] Protected
Address Range Protected Size
000 0x07C0-0x07FF 64 bytes
001 0x0780-0x07FF 128 bytes
010 0x0740-0x07FF 192 bytes
011 0x0700-0x07FF 256 bytes
100 0x06C0-0x07FF 320 bytes
101 0x0680-0x07FF 384 bytes
110 0x0640-0x07FF 448 bytes
111 0x0600-0x07FF 512 bytes
Module Base + 0x0005
76543210
RCBEIF CCIF PVIOL ACCERR 0 BLANK 0 0
W
Reset 1 1 0 00000
= Unimplemented or Reserved
Figure 3-9. EEPROM Status Register (ESTAT - Normal Mode)
Module Base + 0x0005
76543210
RCBEIF CCIF PVIOL ACCERR 0 BLANK FAIL DONE
W
Reset 1 1 0 00001
= Unimplemented or Reserved
Figure 3-10. EEPROM Status Register (ESTAT - Special Mode)
Chapter 3 2 Kbyte EEPROM Module (S12EETS2KV1)
MC9S12KG128 Data Sheet, Rev. 1.16
126 Freescale Semiconductor
3.3.2.7 EEPROM Command Register (ECMD)
The ECMD register defines the EEPROM commands.
Table 3-7. ESTAT Field Descriptions
Field Description
7
CBEIF Command Buffer Empty Interrupt Flag — The CBEIF flag indicates that the address, data, and command
buffers are empty so that a new command sequence can be started. The CBEIF flag is cleared by writing a 1 to
CBEIF. Writing a 0 to the CBEIF flag has no effect on CBEIF. Writing a 0 to CBEIF after writing an aligned word
to the EEPROM address space but before CBEIF is cleared will abort a command sequence and cause the
ACCERR flag in the ESTAT register to be set. Writing a 0 to CBEIF outside of a command sequence will not set
the ACCERR flag. The CBEIF flag is used together with the CBEIE bit in the ECNFG register to generate an
interrupt request.
0 Buffers are full
1 Buffers are ready to accept a new command
6
CCIF Command Complete Interrupt Flag The CCIF flag indicatesthat there are no morecommandspending. The
CCIF flag is cleared when CBEIF is cleared and sets automatically upon completion of all active and pending
commands. The CCIF flag does not set when an active command completes and a pending command is fetched
from the command buffer. Writing to the CCIF flag has no effect. The CCIF flag is used together with the CCIE
bit in the ECNFG register to generate an interrupt request.
0 Command in progress
1 All commands are completed
5
PVIOL Protection Violation — The PVIOL flag indicates an attempt was made to program or erase an address in a
protected EEPROM memory area (Section 3.4.1.4, “Illegal EEPROM Operations”). The PVIOL flag is cleared by
writing a 1 to PVIOL. Writing a 0 to the PVIOL flag has no effect on PVIOL. While PVIOL is set, it is not possible
to launch another command in the EEPROM.
0 No failure
1 A protection violation has occurred
4
ACCERR EEPROM Access Error — The ACCERR flag indicates an illegal access to the selected EEPROM array
(Section 3.4.1.4, “Illegal EEPROM Operations). This can be either a violation of the command sequence, issuing
an illegal command (illegal combination of the CMDBx bits in the ECMD register) or the execution of a CPU
STOP instruction while a command is executing (CCIF = 0). The ACCERR flag is cleared by writing a 1 to
ACCERR. Writing a 0 to the ACCERR flag has no effect on ACCERR. While ACCERR is set, it is not possible to
launch another command in the EEPROM.
0 No failure
1 Access error has occurred
2
BLANK Array Has Been Verified as Erased — The BLANK flag indicates that an erase verify command has checked
the EEPROM array and found it to be erased. The BLANK flag is cleared by hardware when CBEIF is cleared
as part of a new valid command sequence. Writing to the BLANK flag has no effect on BLANK.
0 If an erase verify command has been requested and the CCIF flag is set, then a 0 in BLANK indicates array
is not erased
1 EEPROM array verifies as erased
1
FAIL Flag Indicating a Failed EEPROM Operation — The FAIL flag will set if the erase verify operation fails
(EEPROM block verified as not erased). The FAIL flag is cleared writing a 1 to FAIL. Writing a 0 to the FAIL flag
has no effect on FAIL.
0 EEPROM operation completed without error
1 EEPROM operation failed
0
DONE Flag Indicating a Completed EEPROM Operation
0 EEPROM operation is active (program, erase, erase verify)
1 EEPROM operation not active
Chapter 3 2 Kbyte EEPROM Module (S12EETS2KV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 127
CMDB6, CMDB5, CMDB2, and CMDB0 bits are readable and writable during a command sequence
while bits 7, 4, 3, and 1 read 0 and are not writable.
3.3.2.8 RESERVED3
This register is reserved for factory testing and is not accessible to the user.
All bits read 0 and are not writable.
Module Base + 0x0006
76543210
R0 CMDB6 CMDB5 00
CMDB2 0CMDB0
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 3-11. EEPROM Command Register (ECMD)
Table 3-8. ECMD Field Descriptions
Field Description
6, 5, 2, 0
CMDB[6:5]
CMDB2
CMDB0
EEPROM Command — Valid EEPROM commands are shown in Table 3-9. Any other command written than
those mentioned in Table 3-9 sets the ACCERR bit in the ESTAT register.
Table 3-9. Valid EEPROM Command List
Command Meaning
0x05 Erase verify
0x20 Word program
0x40 Sector erase
0x41 Mass erase
0x60 Sector modify
Module Base + 0x0007
76543210
R00000000
W
Reset 00000000
= Unimplemented or Reserved
Figure 3-12. RESERVED3
Chapter 3 2 Kbyte EEPROM Module (S12EETS2KV1)
MC9S12KG128 Data Sheet, Rev. 1.16
128 Freescale Semiconductor
3.3.2.9 EEPROM Address Register (EADDR)
EADDRHI and EADDRLO are the EEPROM address registers.
In normal modes, all EADDRHI and EADDRLO bits read 0 and are not writable.
In special modes, all EADDRHI and EADDRLO bits are readable and writable except EADDRHI[7:2]
which are not writable and always read 0.
For sector erase, the MCU address bits AB[1:0] are ignored.
For mass erase, any address within the block is valid to start the command.
Module Base + 0x0008
76543210
R000000 EABHI
W
Reset 00000000
= Unimplemented or Reserved
Figure 3-13. EEPROM Address High Register (EADDRHI)
Module Base + 0x0009
76543210
REABLO
W
Reset 00000000
Figure 3-14. EEPROM Address Low Register (EADDRLO)
Chapter 3 2 Kbyte EEPROM Module (S12EETS2KV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 129
3.3.2.10 EEPROM Data Register (EDATA)
EDATAHI and EDATALO are the EEPROM data registers.
In normal modes, all EDATAHI and EDATALO bits read 0 and are not writable.
In special modes, all EDATAHI and EDATALO bits are readable and writable.
3.4 Functional Description
3.4.1 Program and Erase Operation
Write and read operations are both used for the program and erase algorithms described in this subsection.
These algorithms are controlled by a state machine whose timebase, EECLK, is derived from the oscillator
clock via a programmable divider. The command register as well as the associated address and data
registers operate as a buffer and a register (2-stage FIFO) so that a new command along with the necessary
data and address can be stored to the buffer while the previous command is remains in progress. The
pipelined operation allows a simplification of command launching. Buffer empty as well as command
completion are signalled by flags in the EEPROM status register. Interrupts for the EEPROM will be
generated if enabled.
The next four subsections describe:
How to write the ECLKDIV register.
Command write sequences used to program, erase, and verify the EEPROM memory.
Valid EEPROM commands.
Errors resulting from illegal EEPROM operations.
Module Base + 0x000A
76543210
REDHI
W
Reset 00000000
Figure 3-15. EEPROM Data High Register (EDATAHI)
Module Base + 0x000B
76543210
REDLO
W
Reset 00000000
Figure 3-16. EEPROM Data Low Register (EDATALO)
Chapter 3 2 Kbyte EEPROM Module (S12EETS2KV1)
MC9S12KG128 Data Sheet, Rev. 1.16
130 Freescale Semiconductor
3.4.1.1 Writing the ECLKDIV Register
Prior to issuing any program or erase command, it is first necessary to write the ECLKDIV register to
divide the oscillator down to within 150 kHz to 200 kHz range. The program and erase timings are also a
function of the bus clock, such that the ECLKDIV determination must take this information into account.
If we define:
EECLK as the clock of the EEPROM timing control block
Tbus as the period of the bus clock
INT(x) as taking the integer part of x (e.g., INT(4.323)=4), then ECLKDIV register bits PRDIV8
and EDIV[5:0] are to be set as described in Figure 3-17.
For example, if the oscillator clock is 950 kHz and the bus clock is 10 MHz, ECLKDIV bits EDIV[5:0]
must be set to 4 (binary 000100) and bit PRDIV8 set to 0. The resulting EECLK is then 190 kHz. As a
result, the EEPROM algorithm timings are increased over optimum target by:
Command execution time will increase proportionally with the period of EECLK.
CAUTION
Because of the impact of clock synchronization on the accuracy of the
functional timings, programming or erasing the EEPROM cannot be
performed if the bus clock runs at less than 1 MHz. Programming the
EEPROM with an oscillator clock < 150 kHz must be avoided. Setting
ECLKDIV to a value such that EECLK < 150 kHz can reduce the lifetime
of the EEPROM due to overstress. Setting ECLKDIV to a value such that
(1/EECLK+Tbus) < 5µs can result in incomplete programming or erasure
of the memory array cells.
If the ECLKDIV register is written, the bit EDIVLD is set automatically. If this bit is 0, the register has
not been written since the last reset. EEPROM commands will not be executed if this register has not been
written to.
200 190()200100×5%=
Chapter 3 2 Kbyte EEPROM Module (S12EETS2KV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 131
Figure 3-17. PRDIV8 and EDIV Bits Determination Procedure
PRDIV8 = 1
yes
NO
PRDIV8 = 0 (reset)
EECLK = (PRDCLK)/(1+EDIV[5:0])
PRDCLK = oscillator clock
PRDCLK = oscillator clock/8
PRDCLK[MHz]*(5+Tbus[µs]) NO
EDIV[5:0] = PRDCLK[MHz]*(5+Tbus[µs])-1
YES
START
Tbus 1 µs?
an integer?
EDIV[5:0] = INT(PRDCLK[MHz]*(5+Tbus[µs]))
1/EECLK [MHz] + Tbus[ms] 5
AND
EECLK > 0.15 MHz
?
END
YES
NO
EDIV[5:0] 4?
PROGRAM/ERASE IMPOSSIBLE
yes
NO
PROGRAM/ERASE IMPOSSIBLE
NO
TRY TO DECREASE Tbus
YES
OSCILLATOR
CLOCK
> 12.8 MHz?
Chapter 3 2 Kbyte EEPROM Module (S12EETS2KV1)
MC9S12KG128 Data Sheet, Rev. 1.16
132 Freescale Semiconductor
3.4.1.2 Command Write Sequence
The EEPROM command controller is used to supervise the command write sequence to execute program,
erase, mass erase, sector modify, and erase verify operations. Before starting a command write sequence,
it is necessary to check that there is no pending access error or protection violation (the ACCERR and
PVIOL flags must be cleared in the ESTAT register).
After this initial step, the CBEIF flag must be tested to ensure that the address, data and command buffers
are empty. If so, the command sequence can be started. The following 3-step command write sequence
must be strictly adhered to and no intermediate access to the EEPROM array is permitted between the 3
steps. It is possible to read any EEPROM register during a command sequence. The command write
sequence is as follows:
1. Write an aligned word to be to a valid EEPROM array address. The address and data will be stored
in internal buffers.
For program and sector modify, all address and data bits are valid.
For erase, the value of the data bytes are ignored.
For mass erase and erase verify, the address can be anywhere in the available address space of
the array.
For sector erase, the address bits[1:0] are ignored.
2. Write a valid command, listed in Table 3-10, to the ECMD register.
3. Clear the CBEIF flag by writing a 1 to CBEIF to launch the command. When the CBEIF flag is
cleared, the CCIF flag is cleared by hardware indicating that the command was successfully
launched. The CBEIF flag will be set again indicating the address, data, and command buffers are
ready for a new command write sequence to begin.
The completion of the command is indicated by the CCIF flag setting. The CCIF flag only sets when all
active and pending commands have been completed.
The EEPROM command controller will flag errors in command write sequences by means of the
ACCERR (access error) and PVIOL (protection violation) flags in the ESTAT register. An erroneous
command write sequence will abort and set the appropriate flag. If set, the user must clear the ACCERR
or PVIOL flags before commencing another command write sequence. By writing a 0 to the CBEIF flag
the command sequence can be aborted after the word write to the EEPROM address space or after writing
a command to the ECMD register and before the command is launched. Writing a 0 to the CBEIF flag in
this way will set the ACCERR flag.
A summary of the launching of a program operation is shown in Figure 3-18. For other operations, the user
writes the appropriate command to the ECMD register.
Chapter 3 2 Kbyte EEPROM Module (S12EETS2KV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 133
Figure 3-18. Example Program Command Flow
Write: Register ECLKDIV
Read: Register ECLKDIV
Bit EDIVLD set?
Write: Array Address and
Write: Register ECMD
Program Command 0x20
Write: Register ESTAT
yes
no
Clear bit CBEIF 0x80
CBEIF
Set?
Bit yes
Clock Register
Written
Check
1.
2.
3.
Clear bit ACCERR 0x10
Write: Register ESTAT
no
yes
no
Protection
Violation Check
Access
Error Check
Read: Register ESTAT
CCIF
Set?
Bit no
no
Address, Data,
Command
Buffer Empty Check Next Write?
yes
EXIT
no
Program Data
Clear bit PVIOL 0x20
Write: Register ESTAT
yes
PVIOL
Set?
Bit
ACCERR
Set?
Bit
Bit Polling for
Command
Completion Check Read: Register ESTAT
yes
NOTE: command sequence
aborted by writing 0x00 to
ESTAT register.
NOTE: command sequence
aborted by writing 0x00 to
ESTAT register.
Chapter 3 2 Kbyte EEPROM Module (S12EETS2KV1)
MC9S12KG128 Data Sheet, Rev. 1.16
134 Freescale Semiconductor
3.4.1.3 Valid EEPROM Commands
Table 3-10 summarizes the valid EEPROM commands. Also shown are the effects of the commands on
the EEPROM array.
CAUTION
An EEPROM word must be in an erased state before being programmed.
Cumulative programming of bits within a word is not allowed.
The sector modify command (0x60) is a two-step command which first erases a sector (2 words) of the
EEPROM array and then re-programs one of the words in that sector. The EEPROM sector which is erased
by the sector modify command is the sector containing the address of the aligned array write which starts
the valid command sequence. That same address is re-programmed with the data which is written. By
launching a sector modify command and then pipelining a program command it is possible to completely
replace the contents of an EEPROM sector.
3.4.1.4 Illegal EEPROM Operations
The ACCERR flag will be set during the command write sequence if any of the following illegal
operations are performed causing the command write sequence to immediately abort:
1. Writing to the EEPROM address space before initializing ECLKDIV.
2. Writing a misaligned word or a byte to the valid EEPROM address space.
3. Writing to the EEPROM address space while CBEIF is not set.
4. Writing a second word to the EEPROM address space before executing a program or erase
command on the previously written word.
5. Writing to any EEPROM register other than ECMD after writing a word to the EEPROM address
space.
6. Writing a second command to the ECMD register before executing the previously written
command.
7. Writing an invalid command to the ECMD register in normal mode.
8. Writing to any EEPROM register other than ESTAT (to clear CBEIF) after writing to the command
register (ECMD).
Table 3-10. Valid EEPROM Commands
ECMD Meaning Function on EEPROM Array
0x05 Erase Verify Verify all memory bytes of the EEPROM array are erased. If the array is erased, the BLANK bit
will set in the ESTAT register upon command completion.
0x20 Program Program a word (two bytes).
0x40 Sector Erase Erase two words (four bytes) of EEPROM array.
0x41 Mass Erase Erase all of the EEPROM array. A mass erase of the full array is only possible when EPDIS and
EPOPEN are set.
0x60 Sector Modify Erase two words of EEPROM, re-program one word.
Chapter 3 2 Kbyte EEPROM Module (S12EETS2KV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 135
9. The part enters stop mode and a program or erase command is in progress. The command is aborted
and any pending command is killed.
10. A 0 is written to the CBEIF bit in the ESTAT register.
The ACCERR flag will not be set if any EEPROM register is read during the command sequence.
If the EEPROM array is read during execution of an algorithm (i.e., CCIF bit in the ESTAT register is
low), the read will return non-valid data and the ACCERR flag will not be set.
When an ACCERR flag is set in the ESTAT register, the command state machine is locked. It is not
possible to launch another command until the ACCERR flag is cleared.
The PVIOL flag will be set during the command write sequence after the word write to the EEPROM
address space and the command sequence will be aborted if any of the following illegal operations are
performed.
1. Writing a EEPROM address to program in a protected area of the EEPROM.
2. Writing a EEPROM address to erase in a protected area of the EEPROM.
3. Writing the mass erase command to ECMD while any protection is enabled.
When the PVIOL flag is set in the ESTAT register the command state machine is locked. It is not possible
to launch another command until the PVIOL flag is cleared.
3.5 Operating Modes
3.5.1 Wait Mode
If an EEPROM command is active (CCIF = 0) when the MCU enters wait mode, that command and any
pending command will be completed.
The EETS2K module can recover the MCU from wait mode if the interrupts are enabled (see Section 3.7,
“Interrupts”).
3.5.2 Stop Mode
If a command is active (CCIF = 0) when the MCU enters stop mode, the operation will be aborted and if
the operation is program, erase, or sector modify, the data being programmed or erased may be corrupted
and the CCIF and ACCERR flags will be set. If active, the high voltage circuitry to the EEPROM array
will be switched off when entering stop mode. Upon exit from stop mode, the CBEIF flag is set and any
pending command will not be launched. The ACCERR flag must be cleared before starting a new
command write sequence.
NOTE
As active commands are immediately aborted when the MCU enters stop
mode, it is strongly recommended that the user does not use the STOP
instruction during program, erase, or sector modify operations.
Chapter 3 2 Kbyte EEPROM Module (S12EETS2KV1)
MC9S12KG128 Data Sheet, Rev. 1.16
136 Freescale Semiconductor
3.5.3 Background Debug Mode
In background debug mode (BDM), the EPROT register is writable. If the chip is unsecured then all
EEPROM commands listed in Table 3-10 can be executed. If the chip is secured in special single-chip
mode, then the only possible command to execute is mass erase.
3.6 Resets
If a reset occurs while any EEPROM command is in progress, that command will be immediately aborted.
The state of the word being programmed or the sector / block being erased is not guaranteed.
3.7 Interrupts
The EEPROM module can generate an interrupt when all EEPROM commands are completed or the
address, data, and command buffers are empty.
NOTE
Vector addresses and their relative interrupt priority are determined at the
MCU level.
For a detailed description of the register bits, refer to Section 3.3.2.4, “EEPROM Configuration Register
(ECNFG)” and Section 3.3.2.6, “EEPROM Status Register (ESTAT)”.
Table 3-11. EEPROM Interrupt Sources
Interrupt Source Interrupt Flag Local Enable Global (CCR) Mask
EEPROM address, data and
command buffers empty CBEIF
(ESTAT register) CBEIE I Bit
All commands are completed
on EEPROM CCIF
(ESTAT register) CCIE I Bit
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 137
Chapter 4
Port Integration Module (PIM9KG128V1)
4.1 Introduction
The Port Integration Module (PIM) establishes the interface between the peripheral modules and the I/O
pins for ports H, J, M, P, S and T.
This section covers:
Port H associated with the two SPI modules — SPI1 and SPI2. These ports can also be used as
external interrupt sources.
Port J associated with 1 IIC module and the CAN4 module, which can also be used as an external
interrupt source
Port M associated with 2 CAN modules CAN0 and CAN4, the SPI module associated with port
S
Port P connected to either the PWM or the two SPI modules associated with Port H, which also can
be used as an external interrupt source
Port S associated with 2 SCI and 1 SPI module
Port T connected to TIM module
Each I/O pin can be configured by several registers in order to select data direction and drive strength, to
enable and select pull-up or pull-down resistors. On certain pins also interrupts can be enabled which result
in status flags.
The I/O’s of 2 CAN and all 3 SPI modules can be routed from their default location to determined pins.
4.1.1 Features
A standard port has the following minimum features:
Input/output selection
3.3V/5V output drive with two selectable drive strength
3.3V/5V digital and analog input
Input with selectable pull-up or pull-down device
Optional features:
Open drain for wired-OR connections
Interrupt inputs with glitch filtering
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
138 Freescale Semiconductor
4.1.2 Block Diagram
Figure 4-1 is a block diagram of the PIM9KG128.
Figure 4-1. PIM9KG128 Block Diagram
Port T
PT0
PT1
PT2
PT3
PT4
PT5
PT6
PT7
TIM
IOC0
IOC1
IOC2
IOC3
IOC4
IOC5
IOC6
IOC7
Port P
PP0
PP1
PP2
PP3
PP4
PP5
PP6
PP7
PWM
PW0
PW1
PW2
PW3
PW4
PW5
PW6
PW7
Port S
PS0
PS1
PS2
PS3
PS4
PS5
PS6
PS7
RXD
TXD
RXD
TXD
SDI/MISO
SDO/MOSI
SCK
SS
SCI0
SCI1
SPI0
Port H
PH0
PH1
PH2
PH3
PH4
PH5
PH6
PH7
Port J
PJ0
PJ1
PJ6
PJ7
Port M
PM0
PM1
PM2
PM3
PM4
PM5
PM6
PM7
Port Integration Module
IP-Bus
INTJ
INTH
INTP
KWP0
KWP1
KWP2
KWP3
KWP4
KWP5
KWP6
KWP7
KWH0
KWH1
KWH2
KWH3
KWH4
KWH5
KWH6
KWH7
SDI/MISO
SDO/MOSI
SCK
SS
SPI1
SDI/MISO
SDO/MOSI
SCK
SS
SPI2
Module to
Port Routing
RxCAN
TxCAN CAN0
RxCAN
TxCAN CAN4
SDA
SCL IIC
KWJ0
KWJ1
KWW6
KWW7
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 139
4.2 External Signal Description
This section lists and describes the signals that do connect off chip.
4.2.1 Signal Properties
Table 4-1 shows all the pins and their functions that are controlled by the PIM9KG128. If there is more
than one function associated with a pin, the priority is indicated by the position in the table from top
(highest priority) to down (lowest priority). All pins have reset state as input.
Table 4-1. Pin Functions and Priorities (Sheet 1 of 4)
Port Pin
Name Pin Function
and Priority Description Pull
Mode
after Reset
Pin
Function
after Reset
Port T PT[7:0] IOC[7:0] Timer Channels 7 to 0 Hi-Z GPIO
GPIO General-purpose I/O
Port S PS7 SS0 Serial Peripheral Interface 0 slave select output in
master mode, input in slave mode or master mode. Pull-up GPIO
GPIO General-purpose I/O
PS6 SCK0 Serial Peripheral Interface 0 serial clock pin
GPIO General-purpose I/O
PS5 MOSI0 Serial Peripheral Interface 0 master out/slave in pin
GPIO General-purpose I/O
PS4 MISO0 Serial Peripheral Interface 0 master in/slave out pin
GPIO General-purpose I/O
PS3 TXD1 Serial Communication Interface 1 transmit pin
GPIO General-purpose I/O
PS2 RXD1 Serial Communication Interface 1 receive pin
GPIO General-purpose I/O
PS1 TXD0 Serial Communication Interface 0 transmit pin
GPIO General-purpose I/O
PS0 RXD0 Serial Communication Interface 0 receive pin
GPIO General-purpose I/O
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
140 Freescale Semiconductor
Port M
PM7 TXCAN4 MSCAN4 transmit pin
Hi-Z GPIO
GPIO General-purpose I/O
PM6 RXCAN4 MSCAN4 receive pin
GPIO General-purpose I/O
PM5
TXCAN0 MSCAN0 transmit pin
TXCAN4 MSCAN4 transmit pin
SCK0 Serial Peripheral Interface 0 serial clock pin
GPIO General-purpose I/O
PM4
RXCAN0 MSCAN0 receive pin
RXCAN4 MSCAN4 receive pin
MOSI0 Serial Peripheral Interface 0 master out/slave in pin
GPIO General-purpose I/O
PM3
TXCAN0 MSCAN0 transmit pin
SS01Serial Peripheral Interface 0 slave select output in
master mode, input for slave mode or master mode.
GPIO General-purpose I/O
PM2
RXCAN0 MSCAN0 receive pin
MISO01Serial Peripheral Interface 0 master in/slave out pin
GPIO General-purpose I/O
PM1 TXCAN0 MSCAN0 transmit pin
GPIO General-purpose I/O
PM0 RXCAN0 MSCAN0 receive pin
GPIO General-purpose I/O
Table 4-1. Pin Functions and Priorities (Sheet 2 of 4)
Port Pin
Name Pin Function
and Priority Description Pull
Mode
after Reset
Pin
Function
after Reset
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 141
Port P
PP7 PWM7 Pulse Width Modulator channel 7
Hi-Z GPIO
SCK2 Serial Peripheral Interface 2 serial clock pin
GPIO/KWP7 General-purpose I/O with interrupt
PP6
PWM6 Pulse Width Modulator channel 6
SS2 Serial Peripheral Interface 2 slave select output in
master mode, input in slave mode or master mode.
GPIO/KWP6 General-purpose I/O with interrupt
PP5 PWM5 Pulse Width Modulator channel 5
MOSI2 Serial Peripheral Interface 2 master out/slave in pin
GPIO/KWP5 General-purpose I/O with interrupt
PP4 PWM4 Pulse Width Modulator channel 4
MISO2 Serial Peripheral Interface 2 master in/slave out pin
GPIO/KWP4 General-purpose I/O with interrupt
PP3
PWM3 Pulse Width Modulator channel 3
SS1 Serial Peripheral Interface 1 slave select output in
master mode, input in slave mode or master mode.
GPIO/KWP3 General-purpose I/O with interrupt
PP2 PWM2 Pulse Width Modulator channel 2
SCK1 Serial Peripheral Interface 1 serial clock pin
GPIO/KWP2 General-purpose I/O with interrupt
PP1 PWM1 Pulse Width Modulator channel 1
MOSI1 Serial Peripheral Interface 1 master out/slave in pin
GPIO/KWP1 General-purpose I/O with interrupt
PP0 PWM0 Pulse Width Modulator channel 0
MISO1 Serial Peripheral Interface 1 master in/slave out pin
GPIO/KWP0 General-purpose I/O with interrupt
Table 4-1. Pin Functions and Priorities (Sheet 3 of 4)
Port Pin
Name Pin Function
and Priority Description Pull
Mode
after Reset
Pin
Function
after Reset
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
142 Freescale Semiconductor
Port H
PH7 SS2 Serial Peripheral Interface 2 slave select output in
master mode, input in slave mode or master mode.
Hi-Z GPIO
GPIO/KWH7 General-purpose I/O with interrupt
PH6 SCK2 Serial Peripheral Interface 2 serial clock pin
GPIO/KWH6 General-purpose I/O with interrupt
PH5 MOSI2 Serial Peripheral Interface 2 master out/slave in pin
GPIO/KWH5 General-purpose I/O with interrupt
PH4 MISO2 Serial Peripheral Interface 2 master in/slave out pin
GPIO/KWH4 General-purpose I/O with interrupt
PH3 SS1 Serial Peripheral Interface 1 slave select output in
master mode, input in slave mode or master mode.
GPIO/KWH3 General-purpose I/O with interrupt
PH2 SCK1 Serial Peripheral Interface 1 serial clock pin
GPIO/KWH2 General-purpose I/O with interrupt
PH1 MOSI1 Serial Peripheral Interface 1 master out/slave in pin
GPIO/KWH1 General-purpose I/O with interrupt
PH0 MISO1 Serial Peripheral Interface 1 master in/slave out pin
GPIO/KWH0 General-purpose I/O with interrupt
Port J
PJ7 TXCAN4 MSCAN4 transmit pin
Pull-up GPIO
SCL Inter Integrated Circuit serial clock line
GPIO/KWJ7 General-purpose I/O with interrupt
PJ6 RXCAN4 MSCAN4 receive pin
SDA Inter Integrated Circuit serial data line
GPIO/KWJ6 General-purpose I/O with interrupt
PJ1 GPIO/KWJ1 General-purpose I/O with interrupt
PJ0 GPIO/KWJ0 General-purpose I/O with interrupt
1If CAN0 is routed to PM[3:2] the SPI0 can still be used in bidirectional master mode.
Table 4-1. Pin Functions and Priorities (Sheet 4 of 4)
Port Pin
Name Pin Function
and Priority Description Pull
Mode
after Reset
Pin
Function
after Reset
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 143
4.3 Memory Map and Register Definition
This section provides a detailed description of all registers. Table 4-2 is a standard memory map of
PIM9KG128.
Table 4-2. PIM9KG128 Memory Map
Address Offset Use Access
0x0000 Port T I/O Register (PTT) R/W
0x0001 Port T Input Register (PTIT) R
0x0002 Port T Data Direction Register (DDRT) R/W
0x0003 Port T Reduced Drive Register (RDRT) R/W
0x0004 Port T Pull Device Enable Register (PERT) R/W
0x0005 Port T Polarity Select Register (PPST) R/W
0x0006 - 0x0007 Reserved
0x0008 Port S I/O Register (PTS) R/W
0x0009 Port S Input Register (PTIS) R
0x000A Port S Data Direction Register (DDRS) R/W
0x000B Port S Reduced Drive Register (RDRS) R/W
0x000C Port S Pull Device Enable Register (PERS) R/W
0x000D Port S Polarity Select Register (PPSS) R/W
0x000E Port S Wired-OR Mode Register (WOMS) R/W
0x000F Reserved
0x0010 Port M I/O Register (PTM) R/W
0x0011 Port M Input Register (PTIM) R
0x0012 Port M Data Direction Register (DDRM) R/W
0x0013 Port M Reduced Drive Register (RDRM) R/W
0x0014 Port M Pull Device Enable Register (PERM) R/W
0x0015 Port M Polarity Select Register (PPSM) R/W
0x0016 Port M Wired-OR Mode Register (WOMM) R/W
0x0017 Port M Module Routing Register (MODRR) R/W
0x0018 Port P I/O Register (PTP) R/W
0x0019 Port P Input Register (PTIP) R
0x001A Port P Data Direction Register (DDRP) R/W
0x001B Port P Reduced Drive Register (RDRP) R/W
0x001C Port P Pull Device Enable Register (PERP) R/W
0x001D Port P Polarity Select Register (PPSP) R/W
0x001E Port P Interrupt Enable Register (PIEP) R/W
0x001F Port P Interrupt Flag Register (PIFP) R/W
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
144 Freescale Semiconductor
0x0020 Port H I/O Register (PTH) R/W
0x0021 Port H Input Register (PTIH) R
0x0022 Port H Data Direction Register (DDRH) R/W
0x0023 Port H Reduced Drive Register (RDRH) R/W
0x0024 Port H Pull Device Enable Register (PERH) R/W
0x0025 Port H Polarity Select Register (PPSH) R/W
0x0026 Port H Interrupt Enable Register (PIEH) R/W
0x0027 Port H Interrupt Flag Register (PIFH) R/W
0x0028 Port J I/O Register (PTJ) R/W
0x0029 Port J Input Register (PTIJ) R
0x002A Port J Data Direction Register (DDRJ) R/W
0x002B Port J Reduced Drive Register (RDRJ) R/W
0x002C Port J Pull Device Enable Register (PERJ) R/W
0x002D Port J Polarity Select Register (PPSJ) R/W
0x002E Port J Interrupt Enable Register (PIEJ) R/W
0x002F Port J Interrupt Flag Register (PIFJ) R/W
0x0030 - 0x003F Reserved
Table 4-2. PIM9KG128 Memory Map (continued)
Address Offset Use Access
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 145
4.3.1 Port T Registers
Port T is associated with the 8-channel timer (TIM). Each pin is assigned to these modules according to
the following priority: Timer > general-purpose I/O.
If the timer is enabled, the timer channels configured for output compare are available on port T pins
PT[7:0].
Refer to the TIM block description chapter for information on enabling and disabling the TIM module.
During reset, port T pins are configured as high-impedance inputs.
4.3.1.1 Port T I/O Register (PTT)
Read: Anytime. Write: Anytime.
If the data direction bits of the associated I/O pins are set to 1, a read returns the value of the port register,
otherwise the value at the pins is read.
4.3.1.2 Port T Input Register (PTIT)
Read: Anytime. Write: Never, writes to this register have no effect.
This register always reads back the status of the associated pins.
Module Base + 0x0000
76543210
RPTT7 PTT6 PTT5 PTT4 PTT3 PTT2 PTT1 PTT0
W
Timer IOC7 IOC6 IOC5 IOC4 IOC3 IOC2 IOC1 IOC0
Reset 0 0 0 00000
Figure 4-2. Port T I/O Register (PTT))
Module Base + 0x0001
76543210
R PTIT7 PTIT6 PTIT5 PTIT4 PTIT3 PTIT2 PTIT1 PTIT0
W
Reset u u u uuuuu
= Reserved or Unimplemented u = Unaffected by reset
Figure 4-3. Port T Input Register (PTIT)
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
146 Freescale Semiconductor
4.3.1.3 Port T Data Direction Register (DDRT)
Read: Anytime. Write: Anytime.
This register configures each port T pin as either input or output. The TIM forces the I/O state to be an
output for each timer port associated with an enabled output compare. In these cases the data direction bits
will not change. The DDRT bits revert to controlling the I/O direction of a pin when the associated timer
output compare is disabled. The timer input capture always monitors the state of the pin.
4.3.1.4 Port T Reduced Drive Register (RDRT)
Read: Anytime. Write: Anytime.
This register configures the drive strength of each port T output pin as either full or reduced. If the port is
used as input this bit is ignored.
Module Base + 0x0002
76543210
RDDRT7 DDRT6 DDRT5 DDRT4 DDRT3 DDRT2 DDRT1 DDRT0
W
Reset 0 0 0 00000
Figure 4-4. Port T Data Direction Register (DDRT)
Table 4-3. DDRT Field Descriptions
Field Description
7–0
DDRT[7:0] Data Direction Port T
0 Associated pin is configured as input.
1 Associated pin is configured as output.
Module Base + 0x0003
76543210
RRDRT7 RDRT6 RDRT5 RDRT4 RDRT3 RDRT2 RDRT1 RDRT0
W
Reset 0 0 0 00000
Figure 4-5. Port T Reduced Drive Register (RDRT)
Table 4-4. RDRT Field Descriptions
Field Description
7–0
RDRT[7:0] Reduced Drive Port T
0 Full drive strength at output.
1 Associated pin drives at about 1/6 of the full drive strength.
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 147
4.3.1.5 Port T Pull Device Enable Register (PERT)
Read: Anytime. Write: Anytime.
This register configures whether a pull-up or a pull-down device is activated, if the port is used as input.
This bit has no effect if the port is used as output. Out of reset no pull device is enabled.
4.3.1.6 Port T Polarity Select Register (PPST)
Read: Anytime. Write: Anytime.
This register selects whether a pull-down or a pull-up device is connected to the pin.
Module Base + 0x0004
76543210
RPERT7 PERT6 PERT5 PERT4 PERT3 PERT2 PERT1 PERT0
W
Reset 0 0 0 00000
Figure 4-6. Port T Pull Device Enable Register (PERT)
Table 4-5. PERT Field Descriptions
Field Description
7–0
PERT[7:0] Pull Device Enable Port T
0 Pull-up or pull-down device is disabled.
1 Either a pull-up or pull-down device is enabled.
Module Base + 0x0005
76543210
RPPST7 PPST6 PPST5 PPST4 PPST3 PPST2 PPST1 PPST0
W
Reset 0 0 0 00000
Figure 4-7. Port T Polarity Select Register (PPST)
Table 4-6. PPST Field Descriptions
Field Description
7–0
PPST[7:0] Pull Select Port T
0 A pull-up device is connected to the associated port T pin, if enabled by the associated bit in register PERT
and if the port is used as input.
1 A pull-down device is connected to the associated port T pin, if enabled by the associated bitin register PERT
and if the port is used as input.
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
148 Freescale Semiconductor
4.3.2 Port S Registers
Port S is associated with the serial peripheral interface (SPI0) and serial communication interfaces (SCI1,
SCI0). Each pin is assigned to these modules according to the following priority: SPI0/SCI1/SCI0 >
general-purpose I/O.
When the SPI0 is enabled, the PS[7:4] pins become SS0, SCK0, MOSI0, and MISO0 respectively. Refer
to the SPI block description chapter for information on enabling and disabling the SPI0. The SPI0 pins can
be re-routed. Refer to Section 4.3.3.8, “Module Routing Register (MODRR)”.
When the SCI1 receiver and transmitter are enabled, the PS[3:2] pins become TXD1 and RXD1
respectively. When the SCI0 receiver and transmitter are enabled, the PS[1:0] pins become TXD0 and
RXD0 respectively. Refer to the SCI block description chapter for information on enabling and disabling
the SCI receiver and transmitter.
During reset, port S pins are configured as inputs with pull-up.
4.3.2.1 Port S I/O Register (PTS)
Read: Anytime. Write: Anytime.
If the data direction bits of the associated I/O pins are set to 1, a read returns the value of the port register,
otherwise the value at the pins is read.
The SPI0 function takes precedence over the general-purpose I/O function if the SPI0 is enabled.
If enabled, the SCI0(1) transmitter takes precedence over the general-purpose I/O function, and the
corresponding TXD0(1) pin is configured as an output. If enabled, the SCI0(1) receiver takes precedence
over the general-purpose I/O function, and the corresponding RXD0(1) pin is configured as an input.
Module Base + 0x0008
76543210
RPTS7 PTS6 PTS5 PTS4 PTS3 PTS2 PTS1 PTS0
W
SPI/SCI SS0 SCK0 MOSI0 MISO0 TXD1 RXD1 TXD0 RXD0
Reset 0 0 0 00000
Figure 4-8. Port S I/O Register (PTS)
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 149
4.3.2.2 Port S Input Register (PTIS)
Read: Anytime. Write: Never, writes to this register have no effect.
This register always reads back the status of the associated pins.
4.3.2.3 Port S Data Direction Register (DDRS)
Read: Anytime. Write: Anytime.
This register configures each port S pin as either input or output.
When the SPI0 is enabled, the PS[7:4] pins become the SPI bidirectional pins. The associated Data
Direction Register bits have no effect.
When the SCI0(1) transmitter is enabled, the PS[1](PS[3]) pin becomes the TXD0(1) output pin and the
associated Data Direction Register bit has no effect. When the SCI0(1) receiver is enabled, the
PS[0](PS[2]) pin becomes the RXD0(1) input pin and the associated Data Direction Register bit has no
effect.
If the SPI0, SCI0 and SCI1 functions are disabled, the corresponding Data Direction Register bit reverts
to control the I/O direction of the associated pin.
Module Base + 0x0009
76543210
R PTIS7 PTIS6 PTIS5 PTIS4 PTIS3 PTIS2 PTIS1 PTIS0
W
Reset u u u uuuuu
= Reserved or Unimplemented u = Unaffected by reset
Figure 4-9. Port S Input Register (PTIS)
Module Base + 0x000A
76543210
RDDRS7 DDRS6 DDRS5 DDRS4 DDRS3 DDRS2 DDRS1 DDRS0
W
Reset 0 0 0 00000
Figure 4-10. Port S Data Direction Register (DDRS)
Table 4-7. DDRS Field Descriptions
Field Description
7–0
DDRS[7:0] Data Direction Port S
0 Associated pin is configured as input.
1 Associated pin is configured as output.
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
150 Freescale Semiconductor
4.3.2.4 Port S Reduced Drive Register (RDRS)
Read: Anytime. Write: Anytime.
This register configures the drive strength of each port S output pin as either full or reduced. If the port is
used as input this bit is ignored.
4.3.2.5 Port S Pull Device Enable Register (PERS)
Read: Anytime. Write: Anytime.
This register configures whether a pull-up or a pull-down device is activated, if the port is used as input or
as output in wired-OR (open drain) mode. This bit has no effect if the port is used as push-pull output. Out
of reset a pull-up device is enabled.
Module Base + 0x000B
76543210
RRDRS7 RDRS6 RDRS5 RDRS4 RDRS3 RDRS2 RDRS1 RDRS0
W
Reset 0 0 0 00000
Figure 4-11. Port S Reduced Drive Register (RDRS)
Table 4-8. RDRS Field Descriptions
Field Description
7–0
RDRS[7:0] Reduced Drive Port S
0 Full drive strength at output.
1 Associated pin drives at about 1/6 of the full drive strength.
Module Base + 0x000C
76543210
RPERS7 PERS6 PERS5 PERS4 PERS3 PERS2 PERS1 PERS0
W
Reset 1 1 1 11111
Figure 4-12. Port S Pull Device Enable Register (PERS)
Table 4-9. PERS Field Descriptions
Field Description
7–0
PERS[7:] Pull Device Enable Port S
0 Pull-up or pull-down device is disabled.
1 Either a pull-up or pull-down device is enabled.
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 151
4.3.2.6 Port S Polarity Select Register (PPSS)
Read: Anytime. Write: Anytime.
This register selects whether a pull-down or a pull-up device is connected to the pin.
4.3.2.7 Port S Wired-OR Mode Register (WOMS)
Read: Anytime. Write: Anytime.
This register configures the output pins as wired-OR. If enabled the output is driven active low only
(open-drain). A logic level of “1” is not driven. It applies also to the SPI and SCI outputs and allows a
multipoint connection of several serial modules. This bit has no influence on pins used as inputs.
Module Base + 0x000D
76543210
RPPSS7 PPSS6 PPSS5 PPSS4 PPSS3 PPSS2 PPSS1 PPSS0
W
Reset 0 0 0 00000
Figure 4-13. Port S Polarity Select Register (PPSS)
Table 4-10. PPSS Field Descriptions
Field Description
7–0
PPSS[7:0] Pull Select Port S
0 A pull-up device is connected to the associated port S pin, if enabled by the associated bit in register PERS
and if the port is used as input or as wired-OR output.
1 A pull-down device is connected to the associated port S pin, if enabled by the associated bit in register PERS
and if the port is used as input.
Module Base + 0x000E
76543210
RWOMS7 WOMS6 WOMS5 WOMS4 WOMS3 WOMS2 WOMS1 WOMS0
W
Reset 0 0 0 00000
Figure 4-14. Port S Wired-OR Mode Register (WOMS)
Table 4-11. WOMS Field Descriptions
Field Description
7–0
WOMS[7:0] Wired-OR Mode Port S
0 Output buffers operate as push-pull outputs.
1 Output buffers operate as open-drain outputs.
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
152 Freescale Semiconductor
4.3.3 Port M Registers
Port M is associated with two Freescale’s scalable controller area network (CAN4, CAN0) and one serial
peripheral interface (SPI0) modules. Each pin is assigned to these modules according to the following
priority: CAN0 > CAN4 > SPI0 > general-purpose I/O.
Refer to the SPI block description chapter for information on enabling and disabling the SPI0. Refer to the
MSCAN block description chapter for information on enabling and disabling CAN0 or CAN4.The SPI0,
CAN0 and CAN4 pins can be re-routed. Refer to Section 4.3.3.8, “Module Routing Register (MODRR)”.
During reset, port M pins are configured as high-impedance inputs.
4.3.3.1 Port M I/O Register (PTM)
Read: Anytime. Write: Anytime.
If the data direction bits of the associated I/O pins are set to 1, a read returns the value of the port register,
otherwise the value at the pins is read.
4.3.3.2 Port M Input Register (PTIM)
Read: Anytime. Write: Never, writes to this register have no effect.
This register always reads back the status of the associated pins.
Module Base + 0x0010
76543210
RPTM7 PTM6 PTM5 PTM4 PTM3 PTM2 PTM1 PTM0
W
SPI0 SCK0 MOSI0 SS0 MISO0
CAN4 TXCAN4 RXCAN4 TXCAN4 RXCAN4
CAN0 TXCAN0 RXCAN0 TXCAN0 RXCAN0 TXCAN0 RXCAN0
Reset 0 0 0 00000
Figure 4-15. Port M I/O Register (PTM)
Module Base + 0x0011
76543210
R PTIM7 PTIM6 PTIM5 PTIM4 PTIM3 PTIM2 PTIM1 PTIM0
W
Reset u u u uuuuu
= Reserved or Unimplemented u = Unaffected by reset
Figure 4-16. Port M Input Register (PTIM)
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 153
4.3.3.3 Port M Data Direction Register (DDRM)
Read: Anytime. Write: Anytime.
This register configures each port M pin as either input or output. The CAN forces the I/O state to be an
output for each port line associated with an enabled output (TXCAN4 and TXCAN0). It also forces the
I/O state to be an input for each port line associated with an enabled input (RXCAN4 and RXCAN0). In
those cases the data direction bits will not change. The DDRM bits revert to controlling the I/O direction
of a pin when the associated peripheral module is disabled.
4.3.3.4 Port M Reduced Drive Register (RDRM)
Read: Anytime. Write: Anytime.
This register configures the drive strength of each port M output pin as either full or reduced. If the port is
used as input this bit is ignored.
Module Base + 0x0012
76543210
RDDRM7 DDRM6 DDRM5 DDRM4 DDRM3 DDRM2 DDRM1 DDRM0
W
Reset 0 0 0 00000
Figure 4-17. Port M Data Direction Register (DDRM)
Table 4-12. DDRM Field Descriptions
Field Description
7–0
DDRM[7:0] Data Direction Port M
0 Associated pin is configured as input.
1 Associated pin is configured as output.
Module Base + 0x0013
76543210
RRDRM7 RDRM6 RDRM5 RDRM4 RDRM3 RDRM2 RDRM1 RDRM0
W
Reset 0 0 0 00000
Figure 4-18. Port M Reduced Drive Register (RDRM)
Table 4-13. RDRM Field Descriptions
Field Description
7–0
RDRM[7:0] Reduced Drive Port M
0 Full drive strength at output.
1 Associated pin drives at about 1/6 of the full drive strength.
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
154 Freescale Semiconductor
4.3.3.5 Port M Pull Device Enable Register (PERM)
Read: Anytime. Write: Anytime.
This register configures whether a pull-up or a pull-down device is activated, if the port is used as input or
wired-OR output. This bit has no effect if the port is used as push-pull output. Out of reset no pull device
is enabled.
4.3.3.6 Port M Polarity Select Register (PPSM)
Read: Anytime. Write: Anytime.
This register selects whether a pull-down or a pull-up device is connected to the pin. If CAN is active a
pull-up device can be activated on the receiver inputs, but not a pull-down.
Module Base + 0x0014
76543210
RPERM7 PERM6 PERM5 PERM4 PERM3 PERM2 PERM1 PERM0
W
Reset 0 0 0 00000
Figure 4-19. Port M Pull Device Enable Register (PERM)
Table 4-14. PERM Field Descriptions
Field Description
7–0
PERM[7:0] Pull Device Enable Port M
0 Pull-up or pull-down device is disabled.
1 Either a pull-up or pull-down device is enabled.
Module Base + 0x0015
76543210
RPPSM7 PPSM6 PPSM5 PPSM4 PPSM3 PPSM2 PPSM1 PPSM0
W
Reset 0 0 0 00000
Figure 4-20. Port M Polarity Select Register (PPSM)
Table 4-15. PPSM Field Descriptions
Field Description
7–0
PPSM[7:0] Pull Select Port M
0 A pull-up device is connected to the associated port M pin, if enabled by the associated bit in register PERM
and if the port is used as general purpose, RXCAN input.
1 Apull-down deviceisconnected to the associatedportM pin, ifenabled bytheassociatedbit in register PERM
and if the port is used as a general purpose but not as RXCAN.
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 155
4.3.3.7 Port M Wired-OR Mode Register (WOMM)
Read: Anytime. Write: Anytime.
This register configures the output pins as wired-OR. If enabled the output is driven active low only
(open-drain). A logic level of “1” is not driven. It applies also to the CAN outputs and allows a multipoint
connection of several serial modules. This bit has no influence on pins used as inputs.
4.3.3.8 Module Routing Register (MODRR)
Read: Anytime. Write: Anytime.
This register configures the re-routing of CAN0, CAN4, SPI0, SPI1 and SPI2 on defined port pins.
Module Base + 0x0016
76543210
RWOMM7 WOMM6 WOMM5 WOMM4 WOMM3 WOMM2 WOMM1 WOMM0
W
Reset 0 0 0 00000
Figure 4-21. Port M Wired-OR Mode Register (WOMM)
Table 4-16. WOMM Field Descriptions
Field Description
7–0
WOMM[7:0] Wired-OR Mode Port M
0 Output buffers operate as push-pull outputs.
1 Output buffers operate as open-drain outputs.
Module Base + 0x0017
76543210
R0 MODRR6 MODRR5 MODRR4 MODRR3 MODRR2 MODRR1 MODRR0
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 4-22. Module Routing Register (MODRR)
Table 4-17. MODRR Field Descriptions
Field Description
6
MODRR6 SPI2 Routing Bit — See Table 4-22.
5
MODRR5 SPI1 Routing Bit — See Table 4-21.
4
MODRR4 SPI0 Routing Bit — See Table 4-20.
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
156 Freescale Semiconductor
3–2
MODRR[3:2] CAN4 Routing Bits — See Table 4-19.
1–0
MODRR[1:0] CAN0 Routing Bits — See Table 4-18.
Table 4-18. CAN0 Routing
MODRR[1] MODRR[0] RXCAN0 TXCAN0
0 0 PM0 PM1
0 1 PM2 PM3
1 0 PM4 PM5
1 1 Reserved
Table 4-19. CAN4 Routing
MODRR[3] MODRR[2] RXCAN4 TXCAN4
0 0 PJ6 PJ7
0 1 PM4 PM5
1 0 PM6 PM7
1 1 Reserved
Table 4-20. SPI0 Routing
MODRR[4] MISO0 MOSI0 SCK0 SS0
0 PS4 PS5 PS6 PS7
1 PM2 PM4 PM5 PM3
Table 4-21. SPI1 Routing
MODRR[5] MISO1 MOSI1 SCK1 SS1
0 PP0 PP1 PP2 PP3
1 PH0 PH1 PH2 PH3
Table 4-22. SPI2 Routing
MODRR[6] MISO2 MOSI2 SCK2 SS2
0 PP4 PP5 PP6 PP7
1 PH4 PH5 PH6 PH7
Table 4-17. MODRR Field Descriptions (continued)
Field Description
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 157
If the SPI0 module is routed on PM[5:4] and used in bidirectional master mode with disabled SS output,
PM[3:2] are free to be used with CAN or GPIO.
Table 4-23. Implemented Modules on Derivatives
Number
of Modules
MSCAN Modules SPI Modules
CAN0 CAN4 SPI0 SPI1 SPI2
3XXXXX
2XXXX
1XX
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
158 Freescale Semiconductor
4.3.4 Port P Registers
Port P is associated with the Pulse Width Modulator (PWM) and two serial peripheral interfaces (SPI1,
SPI2). Each pin is assigned to these modules according to the following priority: PWM > SPI2/SP1 >
general-purpose I/O.
When a PWM channel is enabled, the corresponding pin becomes a PWM output with the exception of of
pin 7 which can be PWM input or output. Refer to the PWM block description chapter for information on
enabling and disabling the PWM channels.
When SPI2 is enabled and the corresponding PWM channels are disabled, the respective pin configuration
for PP[7:4] is determined by several status bits in the SPI2 module. When SPI1 is enabled and the
corresponding PWM channels are disabled, the respective pin configuration for PP[3:0] is determined by
several status bits in the SPI1 module. Refer to the SPI block description chapter for information on
enabling and disabling the SPI. The SPI1 and SPI2 pins can be re-routed. Refer to Section 4.3.3.8,
“Module Routing Register (MODRR)”.
During reset, port P pins are configured as high-impedance inputs.
4.3.4.1 Port P I/O Register (PTP)
Read: Anytime. Write: Anytime.
If the data direction bits of the associated I/O pins are set to 1, a read returns the value of the port register,
otherwise the value at the pins is read.
The PWM function takes precedence over the general purpose I/O function if the associated PWM channel
is enabled. While channels 6-0 are output only if the respective channel is enabled, channel 7 can be PWM
output or input if the shutdown feature is enabled.
The SPI function takes precedence over the general purpose I/O function associated with if enabled. If both
PWM and SPI are enabled the PWM functionality takes precedence.
Module Base + 0x0018
76543210
RPTP7 PTP6 PTP5 PTP4 PTP3 PTP2 PTP1 PTP0
W
PWM PWM7 PWM6 PWM5 PWM4 PWM3 PWM2 PWM1 PWM0
SPI SCK2 SS2 MOSI2 MISO2 SS1 SCK1 MOSI1 MISO1
Reset 0 0 0 00000
Figure 4-23. Port P I/O Register (PTP)
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 159
4.3.4.2 Port P Input Register (PTIP)
Read: Anytime. Write: Never, writes to this register have no effect.
This register always reads back the status of the associated pins.
4.3.4.3 Port P Data Direction Register (DDRP)
Read: Anytime. Write: Anytime.
This register configures each port P pin as either input or output.
If the associated PWM channel or SPI module is enabled this register has no effect on the pins. The PWM
forces the I/O state to be an output for each port line associated with an enabled PWM7-0 channel. Channel
7 can force the pin to input if the shutdown feature is enabled. If a SPI module is enabled, the SPI
determines the pin direction
If the PWM, SPI1 and SPI2 functions are disabled, the corresponding Data Direction Register bit reverts
to control the I/O direction of the associated pin.
Module Base + 0x0019
76543210
R PTIP7 PTIP6 PTIP5 PTIP4 PTIP3 PTIP2 PTIP1 PTIP0
W
Reset u u u uuuuu
= Reserved or Unimplemented u = Unaffected by reset
Figure 4-24. Port P Input Register (PTIP)
Module Base + 0x001A
76543210
RDDRP7 DDRP6 DDRP5 DDRP4 DDRP3 DDRP2 DDRP1 DDRP0
W
Reset 0 0 0 00000
Figure 4-25. Port P Data Direction Register (DDRP)
Table 4-24. DDRP Field Descriptions
Field Description
7–0
DDRP[7:0] Data Direction Port P
0 Associated pin is configured as input.
1 Associated pin is configured as output.
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
160 Freescale Semiconductor
4.3.4.4 Port P Reduced Drive Register (RDRP)
Read: Anytime. Write: Anytime.
This register configures the drive strength of each port P output pin as either full or reduced. If the port is
used as input this bit is ignored.
4.3.4.5 Port P Pull Device Enable Register (PERP)
Read: Anytime. Write: Anytime.
This register configures whether a pull-up or a pull-down device is activated, if the port is used as input.
This bit has no effect if the port is used as output. Out of reset no pull device is enabled.
Module Base + 0x001B
76543210
RRDRP7 RDRP6 RDRP5 RDRP4 RDRP3 RDRP2 RDRP1 RDRP0
W
Reset 0 0 0 00000
Figure 4-26. Port P Reduced Drive Register (RDRP)
Table 4-25. RDRP Field Descriptions
Field Description
7–0
RDRP[7:0] Reduced Drive Port P
0 Full drive strength at output.
1 Associated pin drives at about 1/6 of the full drive strength.
Module Base + 0x001C
76543210
RPERP7 PERP6 PERP5 PERP4 PERP3 PERP2 PERP1 PERP0
W
Reset 0 0 0 00000
Figure 4-27. Port P Pull Device Enable Register (PERP)
Table 4-26. PERP Field Descriptions
Field Description
7–0
PERP[7:0] Pull Device Enable Port P
0 Pull-up or pull-down device is disabled.
1 Either a pull-up or pull-down device is enabled.
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 161
4.3.4.6 Port P Polarity Select Register (PPSP)
Read: Anytime. Write: Anytime.
This register serves a dual purpose by selecting the polarity of the active interrupt edge as well as selecting
a pull-up or pull-down device if enabled.
4.3.4.7 Port P Interrupt Enable Register (PIEP)
Read: Anytime. Write: Anytime.
This register disables or enables on a per pin basis the edge sensitive external interrupt associated with
port P.
Module Base + 0x001D
76543210
RPPSP7 PPSP6 PPSP5 PPSP4 PPSP3 PPSP2 PPSP1 PPSP0
W
Reset 0 0 0 00000
Figure 4-28. Port P Polarity Select Register (PPSP)
Table 4-27. PPSP Field Descriptions
Field Description
7–0
PPSP[7:0] Polarity Select Port P
0 Falling edge on the associated port P pin sets the associated flag bit in the PIFP register.A pull-up device is
connected to the associated port P pin, if enabled by the associated bit in register PERP and if the port is used
as input.
1 Rising edge on the associated port P pin sets the associated flag bit in the PIFP register.A pull-down device
is connected to the associated port P pin, if enabled by the associated bit in register PERP and if the port is
used as input.
Module Base + 0x001E
76543210
RPIEP7 PIEP6 PIEP5 PIEP4 PIEP3 PIEP2 PIEP1 PIEP0
W
Reset 0 0 0 00000
Figure 4-29. Port P Interrupt Enable Register (PIEP)
Table 4-28. PIEP Field Descriptions
Field Description
7–0
PIEP[7:0] Interrupt Enable Port P
0 Interrupt is disabled (interrupt flag masked).
1 Interrupt is enabled.
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
162 Freescale Semiconductor
4.3.4.8 Port P Interrupt Flag Register (PIFP)
Read: Anytime. Write: Anytime.
Each flag is set by an active edge on the associated input pin. This could be a rising or a falling edge based
on the state of the PPSP register. To clear this flag, write “1” to the corresponding bit in the PIFP register.
Writing a “0” has no effect.
Module Base + 0x001F
76543210
RPIFP7 PIFP6 PIFP5 PIFP4 PIFP3 PIFP2 PIFP1 PIFP0
W
Reset 0 0 0 00000
Figure 4-30. Port P Interrupt Flag Register (PIFP)
Table 4-29. Field Descriptions
Field Description
7–0
PIFP[7:0] Interrupt Flags Port P
0 No active edge pending.
Writing a “0” has no effect.
1 Active edge on the associated bit has occurred (an interrupt will occur if the associated enable bit is set).
Writing a “1” clears the associated flag.
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 163
4.3.5 Port H Registers
Port H is associated with two serial peripheral interfaces (SPI1, SPI2). Each pin is assigned to these
modules according to the following priority: SPI2/SP1 > general-purpose I/O.
When SPI2 is enabled, the respective pin configuration for PH[7:4] is determined by several status bits in
the SPI2 module. When SPI1 is enabled, the respective pin configuration for PH[3:0] is determined by
several status bits in the SPI1 module. Refer to the SPI block description chapter for information on
enabling and disabling the SPI. The SPI1 and SPI2 pins can be re-routed. Refer to Section 4.3.3.8,
“Module Routing Register (MODRR)”.
During reset, port H pins are configured as high-impedance inputs.
4.3.5.1 Port H I/O Register (PTH)
Read: Anytime. Write: Anytime.
If the data direction bits of the associated I/O pins are set to 1, a read returns the value of the port register,
otherwise the value at the pins is read.
The SPI function takes precedence over the general purpose I/O if enabled..
4.3.5.2 Port H Input Register (PTIH)
Read: Anytime. Write: Never, writes to this register have no effect.
This register always reads back the status of the associated pins.
Module Base + 0x0020
76543210
RPTH7 PTH6 PTH5 PTH4 PTH3 PTH2 PTH1 PTH0
W
SPI SS2 SCK2 MOSI2 MISO2 SS1 SCK1 MOSI1 MISO1
Reset 0 0 0 00000
Figure 4-31. Port H I/O Register (PTH)
Module Base + 0x0021
76543210
R PTIH7 PTIH6 PTIH5 PTIH4 PTIH3 PTIH2 PTIH1 PTIH0
W
Reset u u u uuuuu
= Reserved or Unimplemented u = Unaffected by reset
Figure 4-32. Port H Input Register (PTIH)
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
164 Freescale Semiconductor
4.3.5.3 Port H Data Direction Register (DDRH)
Read: Anytime. Write: Anytime.
This register configures each port H pin as either input or output.
4.3.5.4 Port H Reduced Drive Register (RDRH)
Read: Anytime. Write: Anytime.
This register configures the drive strength of each port H output pin as either full or reduced. If the port is
used as input this bit is ignored.
Module Base + 0x0022
76543210
RDDRH7 DDRH6 DDRH5 DDRH4 DDRH3 DDRH2 DDRH1 DDRH0
W
Reset 0 0 0 00000
Figure 4-33. Port H Data Direction Register (DDRH)
Table 4-30. DDRH Field Descriptions
Field Description
7–0
DDRH]7:0] Data Direction Port H
0 Associated pin is configured as input.
1 Associated pin is configured as output.
Module Base + 0x0023
76543210
RRDRH7 RDRH6 RDRH5 RDRH4 RDRH3 RDRH2 RDRH1 RDRH0
W
Reset 0 0 0 00000
Figure 4-34. Port H Reduced Drive Register (RDRH)
Table 4-31. RDRH Field Descriptions
Field Description
7–0
RDRH[7:0] Reduced Drive Port H
0 Full drive strength at output.
1 Associated pin drives at about 1/6 of the full drive strength.
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 165
4.3.5.5 Port H Pull Device Enable Register (PERH)
Read: Anytime. Write: Anytime.
This register configures whether a pull-up or a pull-down device is activated, if the port is used as input.
This bit has no effect if the port is used as output. Out of reset no pull device is enabled.
4.3.5.6 Port H Polarity Select Register (PPSH)
Read: Anytime. Write: Anytime.
This register serves a dual purpose by selecting the polarity of the active interrupt edge as well as selecting
a pull-up or pull-down device if enabled.
Module Base + 0x0024
76543210
RPERH7 PERH6 PERH5 PERH4 PERH3 PERH2 PERH1 PERH0
W
Reset 0 0 0 00000
Figure 4-35. Port H Pull Device Enable Register (PERH)
Table 4-32. PERH Field Descriptions
Field Description
7–0
PERH[7:0] Pull Device Enable Port H
0 Pull-up or pull-down device is disabled.
1 Either a pull-up or pull-down device is enabled.
Module Base + 0x0025
76543210
RPPSH7 PPSH6 PPSH5 PPSH4 PPSH3 PPSH2 PPSH1 PPSH0
W
Reset 0 0 0 00000
Figure 4-36. Port H Polarity Select Register (PPSH)
Table 4-33. PPSH Field Descriptions
Field Description
7–0
PPSH[7:0] Polarity Select Port H
0 Falling edge on the associated port H pin sets the associated flag bit in the PIFH register. A pull-up device is
connectedtotheassociatedport H pin, if enabledbythe associated bit in register PERH and if the portis used
as input.
1 Rising edge on the associated port H pin sets the associated flag bit in the PIFH register. A pull-down device
is connected to the associated port H pin, if enabled by the associated bit in register PERH and if the port is
used as input.
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
166 Freescale Semiconductor
4.3.5.7 Port H Interrupt Enable Register (PIEH)
Read: Anytime. Write: Anytime.
This register disables or enables on a per pin basis the edge sensitive external interrupt associated with
port H.
4.3.5.8 Port H Interrupt Flag Register (PIFH)
Read: Anytime. Write: Anytime.
Each flag is set by an active edge on the associated input pin. This could be a rising or a falling edge based
on the state of the PPSH register. To clear this flag, write “1” to the corresponding bit in the PIFH register.
Writing a “0” has no effect.
Module Base + 0x0026
76543210
RPIEH7 PIEH6 PIEH5 PIEH4 PIEH3 PIEH2 PIEH1 PIEH0
W
Reset 0 0 0 00000
Figure 4-37. Port H Interrupt Enable Register (PIEH)
Table 4-34. PIEH Field Descriptions
Field Description
7–0
PIEH[7:0] Interrupt Enable Port H
0 Interrupt is disabled (interrupt flag masked).
1 Interrupt is enabled.
Module Base + 0x0027
76543210
RPIFH7 PIFH6 PIFH5 PIFH4 PIFH3 PIFH2 PIFH1 PIFH0
W
Reset 0 0 0 00000
Figure 4-38. Port H Interrupt Flag Register (PIFH)
Table 4-35. PIFH Field Descriptions
Field Description
7–0
PIFH[7:0] Interrupt Flags Port H
0 No active edge pending. Writing a “0” has no effect.
1 Active edge on the associated bit has occurred (an interrupt will occur if the associated enable bit is set).
Writing a “1” clears the associated flag.
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 167
4.3.6 Port J Registers
Port J is associated with Freescale’s scalable controller area network (CAN4) and Inter-IC bus (IIC)
modules. Each pin is assigned to these modules according to the following priority: CAN4 > IIC >
general-purpose I/O.
The CAN4 function (TXCAN4 and RXCAN4) takes precedence over the IIC and the general purpose I/O
function if the CAN4 module is enabled. Refer to the MSCAN block description chapter for information
on enabling and disabling CAN4.
The IIC function (SCL and SDA) takes precedence over the general purpose I/O function if the IIC is
enabled. If the IIC module takes precedence the SDA and SCL outputs are configured as open drain
outputs. Refer to the IIC block description chapter for information on enabling and disabling the IIC.
During reset, port J pins are configured as inputs with pull-up.
4.3.6.1 Port J I/O Register (PTJ)
Read: Anytime. Write: Anytime.
If the data direction bits of the associated I/O pins are set to 1, a read returns the value of the port register,
otherwise the value at the pins is read.
4.3.6.2 Port J Input Register (PTIJ)
Read: Anytime. Write: Never, writes to this register have no effect.
This register always reads back the status of the associated pins.
Module Base + 0x0028
76543210
RPTJ7 PTJ6 0000
PTJ1 PTJ0
W
CAN4 TXCAN4 RXCAN4
IIC SCL SDA
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 4-39. Port J I/O Register (PTJ)
Module Base + 0x0029
76543210
R PTIJ7 PTIJ6 0 0 0 0 PTIJ1 PTIJ0
W
Reset u u 0 000uu
= Reserved or Unimplemented u = Unaffected by reset
Figure 4-40. Port J Input Register (PTIJ)
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
168 Freescale Semiconductor
4.3.6.3 Port J Data Direction Register (DDRJ)
Read: Anytime. Write: Anytime.
This register configures each port J pin as either input or output.
If enable, CAN4 forces the I/O state to be an output on PJ7 (TXCAN4) and an input on pin PJ6
(RXCAN4). If CAN4 is disabled, the IIC takes control of the I/O if enabled. In these cases the data
direction bits will not change.
The DDRJ bits revert to controlling the I/O direction of a pin when the associated peripheral module is
disabled.
4.3.6.4 Port J Reduced Drive Register (RDRJ)
Read: Anytime. Write: Anytime.
This register configures the drive strength of each port J output pin as either full or reduced. If the port is
used as input this bit is ignored.
Module Base + 0x002A
76543210
RDDRJ7 DDRJ6 0000
DDRJ1 DDRJ0
W
Reset 0 0 ———— 0 0
= Unimplemented or Reserved
Figure 4-41. Port J Data Direction Register (DDRJ)
Table 4-36. Field Descriptions
Field Description
7, 6, 1, 0
DDRJ[7:6]
DDRJ[1:0]
Data Direction Port J
0 Associated pin is configured as input.
1 Associated pin is configured as output.
Module Base + 0x002B
76543210
RRDRJ7 RDRJ6 0000
RDRJ1 RDRJ0
W
Reset 0 0 ———— 0 0
= Unimplemented or Reserved
Figure 4-42. Port J Reduced Drive Register (RDRJ)
Table 4-37. RDRJ Field Descriptions
Field Description
7, 6, 1, 0
RDRJ[7:6]
RDRJ[1:0]
Reduced Drive Port J
0 Full drive strength at output.
1 Associated pin drives at about 1/6 of the full drive strength.
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 169
4.3.6.5 Port J Pull Device Enable Register (PERJ)
Read: Anytime. Write: Anytime.
This register configures whether a pull-up or a pull-down device is activated, if the port is used as input or
as wired-OR output. This bit has no effect if the port is used as push-pull output. Out of reset a pull-up
device is enabled.
4.3.6.6 Port J Polarity Select Register (PPSJ)
Read: Anytime. Write: Anytime.
This register serves a dual purpose by selecting the polarity of the active interrupt edge as well as selecting
a pull-up or pull-down device if enabled.
Module Base + 0x002C
76543210
RPERJ7 PERJ6 0000
PERJ1 PERJ0
W
Reset 1 1 ———— 1 1
= Unimplemented or Reserved
Figure 4-43. Port J Pull Device Enable Register (PERJ)
Table 4-38. PERJ Field Descriptions
Field Description
7, 6, 1, 0
PERJ[7:6]
PERJ[1:0]
Pull Device Enable Port J
0 Pull-up or pull-down device is disabled.
1 Either a pull-up or pull-down device is enabled.
Module Base + 0x002D
76543210
RPPSJ7 PPSJ6 0000
PPSJ1 PPSJ0
W
Reset 0 0 ———— 0 0
= Unimplemented or Reserved
Figure 4-44. Port J Polarity Select Register (PPSJ)
Table 4-39. PPSJ Field Descriptions
Field Description
7, 6, 1, 0
PPSJ[7:6]
PPSJ[1:0]
Polarity Select Port J
0 Falling edge on the associated port J pin sets the associated flag bit in the PIFJ register. A pull-up device is
connected to the associated port J pin, if enabled by the associated bit in register PERJ and if the port is used
as general purpose input or as IIC port.
1 Rising edge on the associated port J pin sets the associated flag bit in the PIFJ register. A pull-down device
is connected to the associated port J pin, if enabled by the associated bit in register PERJ and if the port is
used as input.
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
170 Freescale Semiconductor
4.3.6.7 Port J Interrupt Enable Register (PIEJ)
Read: Anytime. Write: Anytime.
This register disables or enables on a per pin basis the edge sensitive external interrupt associated with
port J.
4.3.6.8 Port J Interrupt Flag Register (PIFJ)
Read: Anytime. Write: Anytime.
Each flag is set by an active edge on the associated input pin. This could be a rising or a falling edge based
on the state of the PPSJ register. To clear this flag, write “1” to the corresponding bit in the PIFJ register.
Writing a “0” has no effect.
Module Base + 0x002E
76543210
RPIEJ7 PIEJ6 0000
PIEJ1 PIEJ0
W
Reset 0 0 ———— 0 0
= Unimplemented or Reserved
Figure 4-45. Port J Interrupt Enable Register (PIEJ)
Table 4-40. PIEJ Field Descriptions
Field Description
7, 6, 1, 0
PIEJ[7:6]
PIEJ[1:0]
Interrupt Enable Port J
0 Interrupt is disabled (interrupt flag masked).
1 Interrupt is enabled.
Module Base + 0x002F
76543210
RPIFJ7 PIFJ6 0000
PIFJ1 PIFJ0
W
Reset 0 0 ———— 0 0
= Unimplemented or Reserved
Figure 4-46. Port J Interrupt Flag Register (PIFJ)
Table 4-41. PIFJ Field Descriptions
Field Description
7, 6, 1, 0
PIFJ[7:6]
PIFJ[1:0]
Interrupt Flags Port J
0 No active edge pending. Writing a “0” has no effect.
1 Active edge on the associated bit has occurred (an interrupt will occur if the associated enable bit is set).
Writing a “1” clears the associated flag.
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 171
4.4 Functional Description
Each pin can act as general purpose I/O. In addition the pin can act as an output from a peripheral module
or an input to a peripheral module. Table 4-42 summarizes the priority in case of multiple enabled modules
trying to control a shared port.
A set of configuration registers is common to all ports. All registers can be written at any time, however a
specific configuration might not become active.
Example:
A selected pull-up resistor does not become active while the port is used as a push-pull output.
4.4.1 I/O Register
The I/O Register holds the value driven out to the pin if the port is used as a general-purpose I/O. Writing
to the I/O Register only has an effect on the pin if the port is used as general-purpose output.
When reading the I/O Register, the value of each pin is returned if the corresponding Data Direction
Register bit is set to 0 (pin configured as input). If the data direction register bits is set to 1, the content of
the I/O Register bit is returned. This is independent of any other configuration (Figure 4-47).
Due to internal synchronization circuits, it can take up to 2 bus cycles until the correct value is read on the
I/O Register when changing the data direction register.
4.4.2 Input Register
The Input Register is a read-only register and generally returns the value of the pin (Figure 4-47). It can
be used to detect overload or short circuit conditions.
Due to internal synchronization circuits, it can take up to 2 bus cycles until the correct value is read on the
Input Register when changing the Data Direction Register.
Table 4-42. Summary of Functional Priority
Port Priority1
1Highest priority >... > lowest priority
T TIMER > GPIO
S SCI0, SCI1, SPI0 > GPIO
M CAN0 > GPIO
CAN0 (routed) > SPI0 (routed) > GPIO
CAN0 (routed) > CAN4 (routed) > SPI0 (routed) > GPIO
CAN4 (routed) > GPIO
P PWM > SPI1, SPI2 > GPIO
H SPI1, SPI2 > GPIO
J CAN4 > IIC > GPIO
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
172 Freescale Semiconductor
4.4.3 Data Direction Register
The Data Direction Register defines whether the pin is used as an input or an output. A Data Direction
Register bit set to 0 configures the pin as an input. A Data Direction Register bit set to 0 configures the pin
as an output. If a peripheral module controls the pin the contents of the data direction register is ignored
(Figure 4-47).
Figure 4-47. Illustration of I/O Pin Functionality
Figure 4-48 shows the state of digital inputs and outputs when an analog module drives the port. When the
analog module is enabled all associated digital output ports are disabled and all associated digital input
ports read “1”.
Figure 4-48. Digital Ports and Analog Module
4.4.4 Reduced Drive Register
If the port is used as an output the Reduced Drive Register allows the configuration of the drive strength.
PTx
DDRx
output enable
module enable
1
0
1
1
0
0
PAD
PTIx
data out
Digital
Module
Analog
Module
1
0
1
PAD
Digital
Input
Digital
Output
1
0
Analog
Module
Enable
Output
PIM Boundary
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 173
4.4.5 Pull Device Enable Register
The Pull Device Enable Register turns on a pull-up or pull-down device. The pull device becomes active
only if the pin is used as an input or as a wired-or output.
4.4.6 Polarity Select Register
The Polarity Select Register selects either a pull-up or pull-down device if enabled. The pull device
becomes active only if the pin is used as an input or as a wired-or output.
4.4.7 Pin Configuration Summary
The following table summarizes the effect on the various configuration bits, data direction (DDR), output
level (I/O), reduced drive (RDR), pull enable (PE), pull select (PS) and interrupt enable (IE) for the ports.
The configuration bit PS is used for two purposes:
1. Configure the sensitive interrupt edge (rising or falling), if interrupt is enabled.
2. Select either a pull-up or pull-down device if PE is active.
NOTE
All bits of all registers in this module are completely synchronous to internal
clocks during a register read.
Table 4-43. Pin Configuration Summary
DDR IO RDR PE PS IE1
1Applicable only on port P, H, and J.
Function Pull Device Interrupt
0 X X 0 X 0 Input Disabled Disabled
0 X X 1 0 0 Input Pull Up Disabled
0 X X 1 1 0 Input Pull Down Disabled
0 X X 0 0 1 Input Disabled Falling edge
0 X X 0 1 1 Input Disabled Rising edge
0 X X 1 0 1 Input Pull Up Falling edge
0 X X 1 1 1 Input Pull Down Rising edge
1 0 0 X X 0 Output, full drive to 0 Disabled Disabled
1 1 0 X X 0 Output, full drive to 1 Disabled Disabled
1 0 1 X X 0 Output, reduced drive to 0 Disabled Disabled
1 1 1 X X 0 Output, reduced drive to 1 Disabled Disabled
1 0 0 X 0 1 Output, full drive to 0 Disabled Falling edge
1 1 0 X 1 1 Output, full drive to 1 Disabled Rising edge
1 0 1 X 0 1 Output, reduced drive to 0 Disabled Falling edge
1 1 1 X 1 1 Output, reduced drive to 1 Disabled Rising edge
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
174 Freescale Semiconductor
4.5 Resets
The reset values of all registers are given in the Register Description in Section 4.3, “Memory Map and
Register Definition”.
4.5.1 Reset Initialization
All registers including the data registers get set/reset asynchronously. Table 4-44 summarizes the port
properties after reset initialization.
4.6 Interrupts
4.6.1 General
Port P, H and J generate a separate edge sensitive interrupt if enabled. Each port offers I/O pins with edge
triggered interrupt capability in wired-or fashion. The interrupt enable as well as the sensitivity to rising
or falling edges can be individually configured on per pin basis. All bits/pins per port share the same
interrupt vector. Interrupts can be used with the pins configured as inputs or outputs.
An interrupt is generated when a bit in the port interrupt flag register and its corresponding port interrupt
enable bit are both set. This external interrupt feature is capable to wake up the CPU when it is in stop or
wait mode.
A digital filter on each pin prevents pulses (Figure 4-49) shorter than a specified time from generating an
interrupt. The minimum time varies over process conditions, temperature and voltage (Figure 4-50 and
Table 4-45).
Figure 4-49. Pulse Illustration
Table 4-44. Port Reset State Summary
Port Reset States
Data
Direction Pull
Mode Reduced
Drive Wired-OR
Mode Interrupt
T Input Hi-Z Disabled N/A N/A
S Input Pull-up Disabled Disabled N/A
M Input Hi-Z Disabled Disabled N/A
P Input Hi-Z Disabled N/A Disabled
H Input Hi-Z Disabled N/A Disabled
J Input Pull-up Disabled N/A Disabled
tpulse
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 175
Figure 4-50. Interrupt Glitch Filter (PPS = 0)
A valid edge on an input is detected if 4 consecutive samples of a passive level are followed by 4
consecutive samples of an active level directly or indirectly.
The filters are continuously clocked by the bus clock in RUN and WAIT mode. In STOP mode the clock
is generated by a single RC oscillator in the port integration module. To maximize current saving the RC
oscillator runs only if the following condition is true on any pin:
Sample count <= 4 and port interrupt enabled (PIE=1) and port interrupt flag not set (PIF=0).
Table 4-45. Pulse Detection Criteria
Pulse
Mode
STOP STOP1
1These values include the spread of the oscillator frequency over temperature,
voltage and process.
Unit Unit
Ignored tpulse <= 3 Bus Clock tpulse <= 3.2 µs
Uncertain 3 < tpulse < 4 Bus Clock 3.2 < tpulse < 10 µs
Valid tpulse >= 4 Bus Clock tpulse >= 10 µs
Glitch, filtered out, no interrupt flag set
Valid pulse, interrupt flag set
tifmin
tifmax
Chapter 4 Port Integration Module (PIM9KG128V1)
MC9S12KG128 Data Sheet, Rev. 1.16
176 Freescale Semiconductor
4.6.2 Interrupt Sources
NOTE
Vector addresses and their relative interrupt priority are determined at the
MCU level.
4.6.3 Operation in Stop Mode
All clocks are stopped in STOP mode. The port integration module has asynchronous paths on port P, H
and J to generate wake-up interrupts from stop mode. For other sources of external interrupts refer to the
respective block description chapters.
Table 4-46. Port Integration Module Interrupt Sources
Interrupt Source Interrupt Flag Local Enable Global (CCR) Mask
Port P PIFP[7:0] PIEP[7:0] I Bit
Port H PIFH[7:0] PIEH[7:0] I Bit
Port J PIFJ[7:6,1:0] PIEJ[7:6,1:0] I Bit
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 177
Chapter 5
Clocks and Reset Generator (CRGV4) Block Description
5.1 Introduction
This specification describes the function of the clocks and reset generator (CRGV4).
5.1.1 Features
The main features of this block are:
Phase-locked loop (PLL) frequency multiplier
Reference divider
Automatic bandwidth control mode for low-jitter operation
Automatic frequency lock detector
CPU interrupt on entry or exit from locked condition
Self-clock mode in absence of reference clock
System clock generator
Clock quality check
Clock switch for either oscillator- or PLL-based system clocks
User selectable disabling of clocks during wait mode for reduced power consumption
Computer operating properly (COP) watchdog timer with time-out clear window
System reset generation from the following possible sources:
Power-on reset
Low voltage reset
Refer to the device overview section for availability of this feature.
COP reset
Loss of clock reset
External pin reset
Real-time interrupt (RTI)
Chapter 5 Clocks and Reset Generator (CRGV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
178 Freescale Semiconductor
5.1.2 Modes of Operation
This subsection lists and briefly describes all operating modes supported by the CRG.
Run mode
All functional parts of the CRG are running during normal run mode. If RTI or COP functionality
is required the individual bits of the associated rate select registers (COPCTL, RTICTL) have to be
set to a nonzero value.
Wait mode
This mode allows to disable the system and core clocks depending on the configuration of the
individual bits in the CLKSEL register.
Stop mode
Depending on the setting of the PSTP bit, stop mode can be differentiated between full stop mode
(PSTP = 0) and pseudo-stop mode (PSTP = 1).
Full stop mode
The oscillator is disabled and thus all system and core clocks are stopped. The COP and the
RTI remain frozen.
Pseudo-stop mode
The oscillator continues to run and most of the system and core clocks are stopped. If the
respective enable bits are set the COP and RTI will continue to run, else they remain frozen.
Self-clock mode
Self-clock mode will be entered if the clock monitor enable bit (CME) and the self-clock mode
enable bit (SCME) are both asserted and the clock monitor in the oscillator block detects a loss of
clock. As soon as self-clock mode is entered the CRGV4 starts to perform a clock quality check.
Self-clock mode remains active until the clock quality check indicates that the required quality of
the incoming clock signal is met (frequency and amplitude). Self-clock mode should be used for
safetypurposesonly. It providesreduced functionalitytothe MCU incasea loss of clockis causing
severe system conditions.
5.1.3 Block Diagram
Figure 5-1 shows a block diagram of the CRGV4.
Chapter 5 Clocks and Reset Generator (CRGV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 179
Figure 5-1. CRG Block Diagram
5.2 External Signal Description
This section lists and describes the signals that connect off chip.
5.2.1 VDDPLL, VSSPLL — PLL Operating Voltage, PLL Ground
These pins provides operating voltage (VDDPLL) and ground (VSSPLL) for the PLL circuitry. This allows
the supply voltage to the PLL to be independently bypassed. Even if PLL usage is not required VDDPLL
and VSSPLL must be connected properly.
5.2.2 XFC — PLL Loop Filter Pin
A passive external loop filter must be placed on the XFC pin. The filter is a second-order, low-pass filter
to eliminate the VCO input ripple. The value of the external filter network and the reference frequency
determines the speed of the corrections and the stability of the PLL. Refer to the device overview chapter
for calculation of PLL loop filter (XFC) components. If PLL usage is not required the XFC pin must be
tied to VDDPLL.
CRG
Registers
Clock and Reset
COP
RESET
RTI
PLL
XFC
VDDPLL
VSSPLL
Oscil-
EXTAL
XTAL
Control
Bus Clock
System Reset
Oscillator Clock
PLLCLK
OSCCLK
Core Clock
Clock
Monitor
CM fail
Clock Quality
Checker
Reset
Generator
XCLKS
Power-on Reset
Low Voltage Reset 1
COP Timeout
Real-Time Interrupt
PLL Lock Interrupt
Self-Clock Mode
Interrupt
lator
Voltage
Regulator
1 Refer to the device overview section for availability of the low-voltage reset feature.
Chapter 5 Clocks and Reset Generator (CRGV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
180 Freescale Semiconductor
Figure 5-2. PLL Loop Filter Connections
5.2.3 RESET — Reset Pin
RESET is an active low bidirectional reset pin. As an input it initializes the MCU asynchronously to a
known start-up state. As an open-drain output it indicates that an system reset (internal to MCU) has been
triggered.
5.3 Memory Map and Register Definition
This section provides a detailed description of all registers accessible in the CRGV4.
5.3.1 Module Memory Map
Table 5-1 gives an overview on all CRGV4 registers.
Table 5-1. CRGV4 Memory Map
Address
Offset Use Access
0x0000 CRG Synthesizer Register (SYNR) R/W
0x0001 CRG Reference Divider Register (REFDV) R/W
0x0002 CRG Test Flags Register (CTFLG)1
1CTFLG is intended for factory test purposes only.
R/W
0x0003 CRG Flags Register (CRGFLG) R/W
0x0004 CRG Interrupt Enable Register (CRGINT) R/W
0x0005 CRG Clock Select Register (CLKSEL) R/W
0x0006 CRG PLL Control Register (PLLCTL) R/W
0x0007 CRG RTI Control Register (RTICTL) R/W
0x0008 CRG COP Control Register (COPCTL) R/W
0x0009 CRG Force and Bypass Test Register (FORBYP)2
2FORBYP is intended for factory test purposes only.
R/W
0x000A CRG Test Control Register (CTCTL)3
3CTCTL is intended for factory test purposes only.
R/W
0x000B CRG COP Arm/Timer Reset (ARMCOP) R/W
MCU
XFC
RS
CS
VDDPLL
CP
Chapter 5 Clocks and Reset Generator (CRGV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 181
NOTE
Register address = base address + address offset, where the base address is
defined at the MCU level and the address offset is defined at the module
level.
5.3.2 Register Descriptions
This section describes in address order all the CRGV4 registers and their individual bits.
Register
Name Bit 7 654321Bit 0
0x0000
SYNR R0 0 SYN5 SYN4 SYN3 SYN2 SYN1 SYN0
W
0x0001
REFDV R0000
REFDV3 REFDV2 REFDV1 REFDV0
W
0x0002
CTFLG R00000000
W
0x0003
CRGFLG RRTIF PORF LVRF LOCKIF LOCK TRACK SCMIF SCM
W
0x0004
CRGINT RRTIE 00
LOCKIE 00
SCMIE 0
W
0x0005
CLKSEL RPLLSEL PSTP SYSWAI ROAWAI PLLWAI CWAI RTIWAI COPWAI
W
0x0006
PLLCTL RCME PLLON AUTO ACQ 0PRE PCE SCME
W
0x0007
RTICTL R0 RTR6 RTR5 RTR4 RTR3 RTR2 RTR1 RTR0
W
0x0008
COPCTL RWCOP RSBCK 000
CR2 CR1 CR0
W
0x0009
FORBYP R00000000
W
0x000A
CTCTL R00000000
W
= Unimplemented or Reserved
Figure 5-3. CRG Register Summary
Chapter 5 Clocks and Reset Generator (CRGV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
182 Freescale Semiconductor
5.3.2.1 CRG Synthesizer Register (SYNR)
The SYNR register controls the multiplication factor of the PLL. If the PLL is on, the count in the loop
divider (SYNR) register effectively multiplies up the PLL clock (PLLCLK) from the reference frequency
by 2 x (SYNR+1). PLLCLK will not be below the minimum VCO frequency (fSCM).
NOTE
If PLL is selected (PLLSEL=1), Bus Clock = PLLCLK / 2
Bus Clock must not exceed the maximum operating system frequency.
Read: anytime
Write: anytime except if PLLSEL = 1
NOTE
Write to this register initializes the lock detector bit and the track detector
bit.
0x000B
ARMCOP R00000000
W Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Module Base + 0x0000
76543210
R0 0 SYN5 SYNR SYN3 SYN2 SYN1 SYN0
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 5-4. CRG Synthesizer Register (SYNR)
Register
Name Bit 7 654321Bit 0
= Unimplemented or Reserved
Figure 5-3. CRG Register Summary (continued)
PLLCLK 2xOSCCLKx SYNR 1+()
REFDV 1+()
-----------------------------------
=
Chapter 5 Clocks and Reset Generator (CRGV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 183
5.3.2.2 CRG Reference Divider Register (REFDV)
The REFDV register provides a finer granularity for the PLL multiplier steps. The count in the reference
divider divides OSCCLK frequency by REFDV + 1.
Read: anytime
Write: anytime except when PLLSEL = 1
NOTE
Write to this register initializes the lock detector bit and the track detector
bit.
5.3.2.3 Reserved Register (CTFLG)
This register is reserved for factory testing of the CRGV4 module and is not available in normal modes.
Read: always reads 0x0000 in normal modes
Write: unimplemented in normal modes
NOTE
Writing to this register when in special mode can alter the CRGV4
functionality.
Module Base + 0x0001
76543210
R0000
REFDV3 REFDV2 REFDV1 REFDV0
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 5-5. CRG Reference Divider Register (REFDV)
Module Base + 0x0002
76543210
R00000000
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 5-6. CRG Reserved Register (CTFLG)
Chapter 5 Clocks and Reset Generator (CRGV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
184 Freescale Semiconductor
5.3.2.4 CRG Flags Register (CRGFLG)
This register provides CRG status bits and flags.
Read: anytime
Write: refer to each bit for individual write conditions
Module Base + 0x0003
76543210
RRTIF PORF LVRF LOCKIF LOCK TRACK SCMIF SCM
W
Reset 0 Note 1 Note 2 00000
1. PORF is set to 1 when a power-on reset occurs. Unaffected by system reset.
2. LVRF is set to 1 when a low-voltage reset occurs. Unaffected by system reset.
= Unimplemented or Reserved
Figure 5-7. CRG Flag Register (CRGFLG)
Table 5-2. CRGFLG Field Descriptions
Field Description
7
RTIF Real-Time Interrupt Flag RTIF is set to 1 at the end of the RTI period. This flag can only be cleared by writing
a 1. Writing a 0 has no effect. If enabled (RTIE = 1), RTIF causes an interrupt request.
0 RTI time-out has not yet occurred.
1 RTI time-out has occurred.
6
PORF Power-on Reset Flag PORF is set to 1 when a power-on reset occurs. This flag can only be cleared by writing
a 1. Writing a 0 has no effect.
0 Power-on reset has not occurred.
1 Power-on reset has occurred.
5
LVRF Low-Voltage Reset Flag If low voltage reset feature is not available (see the device overview chapter), LVRF
always reads 0. LVRF is set to 1 when a low voltage reset occurs. This flag can only be cleared by writing a 1.
Writing a 0 has no effect.
0 Low voltage reset has not occurred.
1 Low voltage reset has occurred.
4
LOCKIF PLL Lock Interrupt Flag LOCKIF is set to 1 when LOCK status bit changes. This flag can only be cleared by
writing a 1. Writing a 0 has no effect.If enabled (LOCKIE = 1), LOCKIF causes an interrupt request.
0 No change in LOCK bit.
1 LOCK bit has changed.
3
LOCK Lock Status Bit LOCK reflects the current state of PLL lock condition. This bit is cleared in self-clock mode.
Writes have no effect.
0 PLL VCO is not within the desired tolerance of the target frequency.
1 PLL VCO is within the desired tolerance of the target frequency.
2
TRACK Track Status Bit TRACKreflects the current stateof PLL trackcondition.This bit iscleared in self-clockmode.
Writes have no effect.
0 Acquisition mode status.
1 Tracking mode status.
Chapter 5 Clocks and Reset Generator (CRGV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 185
5.3.2.5 CRG Interrupt Enable Register (CRGINT)
This register enables CRG interrupt requests.
Read: anytime
Write: anytime
1
SCMIF Self-Clock Mode Interrupt Flag — SCMIF is set to 1 when SCM status bit changes. This flag can only be
cleared by writing a 1. Writing a 0 has no effect. If enabled (SCMIE=1), SCMIF causes an interrupt request.
0 No change in SCM bit.
1 SCM bit has changed.
0
SCM Self-Clock Mode Status Bit — SCM reflects the current clocking mode. Writes have no effect.
0 MCU is operating normally with OSCCLK available.
1 MCU is operating in self-clock mode with OSCCLK in an unknown state. All clocks are derived from PLLCLK
running at its minimum frequency fSCM.
Module Base + 0x0004
76543210
RRTIE 00
LOCKIE 00
SCMIE 0
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 5-8. CRG Interrupt Enable Register (CRGINT)
Table 5-3. CRGINT Field Descriptions
Field Description
7
RTIE Real-Time Interrupt Enable Bit
0 Interrupt requests from RTI are disabled.
1 Interrupt will be requested whenever RTIF is set.
4
LOCKIE Lock Interrupt Enable Bit
0 LOCK interrupt requests are disabled.
1 Interrupt will be requested whenever LOCKIF is set.
1
SCMIE Self-Clock Mode Interrupt Enable Bit
0 SCM interrupt requests are disabled.
1 Interrupt will be requested whenever SCMIF is set.
Table 5-2. CRGFLG Field Descriptions (continued)
Field Description
Chapter 5 Clocks and Reset Generator (CRGV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
186 Freescale Semiconductor
5.3.2.6 CRG Clock Select Register (CLKSEL)
This register controls CRG clock selection. Refer to Figure 5-17 for details on the effect of each bit.
Read: anytime
Write: refer to each bit for individual write conditions
Module Base + 0x0005
76543210
RPLLSEL PSTP SYSWAI ROAWAI PLLWAI CWAI RTIWAI COPWAI
W
Reset 0 0 0 00000
Figure 5-9. CRG Clock Select Register (CLKSEL)
Table 5-4. CLKSEL Field Descriptions
Field Description
7
PLLSEL PLL Select Bit Write anytime. Writing a 1 when LOCK = 0 and AUTO = 1, or TRACK = 0 and AUTO = 0 has
no effect. This prevents the selection of an unstable PLLCLK as SYSCLK. PLLSEL bit is cleared when the MCU
enters self-clock mode, stop mode or wait mode with PLLWAI bit set.
0 System clocks are derived from OSCCLK (Bus Clock = OSCCLK / 2).
1 System clocks are derived from PLLCLK (Bus Clock = PLLCLK / 2).
6
PSTP Pseudo-Stop Bit — Write: anytime — This bit controls the functionality of the oscillator during stop mode.
0 Oscillator is disabled in stop mode.
1 Oscillator continues to run in stop mode (pseudo-stop). The oscillator amplitude is reduced. Refer to oscillator
block description for availability of a reduced oscillator amplitude.
Note: Pseudo-stop allows for faster stop recovery and reduces the mechanical stress and aging of the resonator
in case of frequent stop conditions at the expense of a slightly increased power consumption.
Note: Lower oscillator amplitude exhibits lower power consumption but could have adverse effects during any
electro-magnetic susceptibility (EMS) tests.
5
SYSWAI System Clocks Stop in Wait Mode Bit — Write: anytime
0 In wait mode, the system clocks continue to run.
1 In wait mode, the system clocks stop.
Note: RTI and COP are not affected by SYSWAI bit.
4
ROAWAI Reduced Oscillator Amplitude in Wait Mode Bit — Write: anytime — Refer to oscillator block description
chapter for availability of a reduced oscillator amplitude. If no such feature exists in the oscillator block then
setting this bit to 1 will not have any effect on power consumption.
0 Normal oscillator amplitude in wait mode.
1 Reduced oscillator amplitude in wait mode.
Note: Lower oscillator amplitude exhibits lower power consumption but could have adverse effects during any
electro-magnetic susceptibility (EMS) tests.
3
PLLWAI PLL Stops in Wait Mode Bit Write: anytime If PLLWAI is set, the CRGV4 will clear the PLLSEL bit before
entering wait mode. The PLLON bit remains set during wait mode but the PLL is powered down. Upon exiting
wait mode, the PLLSEL bit has to be set manually if PLL clock is required.
While the PLLWAI bit is set the AUTO bit is set to 1 in order to allow the PLL to automatically lock on the selected
target frequency after exiting wait mode.
0 PLL keeps running in wait mode.
1 PLL stops in wait mode.
Chapter 5 Clocks and Reset Generator (CRGV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 187
5.3.2.7 CRG PLL Control Register (PLLCTL)
This register controls the PLL functionality.
Read: anytime
Write: refer to each bit for individual write conditions
2
CWAI Core Stops in Wait Mode Bit — Write: anytime
0 Core clock keeps running in wait mode.
1 Core clock stops in wait mode.
1
RTIWAI RTI Stops in Wait Mode Bit — Write: anytime
0 RTI keeps running in wait mode.
1 RTI stops and initializes the RTI dividers whenever the part goes into wait mode.
0
COPWAI COP Stops in Wait Mode Bit — Normal modes: Write once —Special modes: Write anytime
0 COP keeps running in wait mode.
1 COP stops and initializes the COP dividers whenever the part goes into wait mode.
Module Base + 0x0006
76543210
RCME PLLON AUTO ACQ 0PRE PCE SCME
W
Reset 1 1 1 10001
= Unimplemented or Reserved
Figure 5-10. CRG PLL Control Register (PLLCTL)
Table 5-5. PLLCTL Field Descriptions
Field Description
7
CME Clock Monitor Enable Bit — CME enables the clock monitor. Write anytime except when SCM = 1.
0 Clock monitor is disabled.
1 Clock monitor is enabled. Slow or stopped clocks will cause a clock monitor reset sequence or self-clock
mode.
Note: Operating with CME = 0 will not detect any loss of clock. In case of poor clock quality this could cause
unpredictable operation of the MCU.
Note: In Stop Mode (PSTP = 0) the clock monitor is disabled independently of the CME bit setting and any loss
of clock will not be detected.
6
PLLON Phase Lock Loop On Bit PLLON turns on the PLL circuitry. In self-clock mode, the PLL is turned on, but the
PLLON bit reads the last latched value. Write anytime except when PLLSEL = 1.
0 PLL is turned off.
1 PLL is turned on. If AUTO bit is set, the PLL will lock automatically.
Table 5-4. CLKSEL Field Descriptions (continued)
Field Description
Chapter 5 Clocks and Reset Generator (CRGV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
188 Freescale Semiconductor
5.3.2.8 CRG RTI Control Register (RTICTL)
This register selects the timeout period for the real-time interrupt.
Read: anytime
Write: anytime
NOTE
A write to this register initializes the RTI counter.
5
AUTO Automatic Bandwidth Control Bit — AUTO selects either the high bandwidth (acquisition) mode or the low
bandwidth (tracking) mode depending on how close to the desired frequency the VCO is running. Write anytime
except when PLLWAI=1, because PLLWAI sets the AUTO bit to 1.
0 Automatic mode control is disabled and the PLL is under software control, using ACQ bit.
1 Automatic mode control is enabled and ACQ bit has no effect.
4
ACQ Acquisition Bit — Write anytime. If AUTO=1 this bit has no effect.
0 Low bandwidth filter is selected.
1 High bandwidth filter is selected.
2
PRE RTI Enable during Pseudo-Stop Bit — PRE enables the RTI during pseudo-stop mode. Write anytime.
0 RTI stops running during pseudo-stop mode.
1 RTI continues running during pseudo-stop mode.
Note: If the PRE bit is cleared the RTI dividers will go static while pseudo-stop mode is active. The RTI dividers
will not initialize like in wait mode with RTIWAI bit set.
1
PCE COP Enable during Pseudo-Stop Bit — PCE enables the COP during pseudo-stop mode. Write anytime.
0 COP stops running during pseudo-stop mode
1 COP continues running during pseudo-stop mode
Note: Ifthe PCE bitis cleared theCOP dividers will gostatic while pseudo-stopmode is active.TheCOP dividers
will not initialize like in wait mode with COPWAI bit set.
0
SCME Self-Clock Mode Enable Bit Normal modes: Write once —Special modes: Write anytime SCME can not
be cleared while operating in self-clock mode (SCM=1).
0 Detection of crystal clock failure causes clock monitor reset (see Section 5.5.1, “Clock Monitor Reset”).
1 Detection of crystal clock failure forces the MCU in self-clock mode (see Section 5.4.7.2, “Self-Clock Mode”).
Module Base + 0x0007
76543210
R0 RTR6 RTR5 RTR4 RTR3 RTR2 RTR1 RTR0
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 5-11. CRG RTI Control Register (RTICTL)
Table 5-5. PLLCTL Field Descriptions (continued)
Field Description
Chapter 5 Clocks and Reset Generator (CRGV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 189
Table 5-6. RTICTL Field Descriptions
Field Description
6:4
RTR[6:4] Real-Time Interrupt Prescale Rate Select Bits These bits select the prescale ratefor the RTI.See Table 5-7.
3:0
RTR[3:0] Real-Time Interrupt Modulus Counter Select Bits — These bits select the modulus counter target value to
provide additional granularity. Table 5-7 shows all possible divide values selectable by the RTICTL register. The
source clock for the RTI is OSCCLK.
Table 5-7. RTI Frequency Divide Rates
RTR[3:0]
RTR[6:4] =
000
(OFF) 001
(210)010
(211)011
(212)100
(213)101
(214)110
(215)111
(216)
0000 (÷1) OFF*210 211 212 213 214 215 216
0001 (÷2) OFF*2x210 2x211 2x212 2x213 2x214 2x215 2x216
0010 (÷3) OFF*3x210 3x211 3x212 3x213 3x214 3x215 3x216
0011 (÷4) OFF*4x210 4x211 4x212 4x213 4x214 4x215 4x216
0100 (÷5) OFF*5x210 5x211 5x212 5x213 5x214 5x215 5x216
0101 (÷6) OFF*6x210 6x211 6x212 6x213 6x214 6x215 6x216
0110 (÷7) OFF*7x210 7x211 7x212 7x213 7x214 7x215 7x216
0111 (÷8) OFF*8x210 8x211 8x212 8x213 8x214 8x215 8x216
1000 (÷9) OFF*9x210 9x211 9x212 9x213 9x214 9x215 9x216
1001 (÷10) OFF*10x210 10x211 10x212 10x213 10x214 10x215 10x216
1010 (÷11) OFF*11x210 11x211 11x212 11x213 11x214 11x215 11x216
1011 (÷12) OFF*12x210 12x211 12x212 12x213 12x214 12x215 12x216
1100 (÷13) OFF*13x210 13x211 13x212 13x213 13x214 13x215 13x216
1101 (÷14) OFF*14x210 14x211 14x212 14x213 14x214 14x215 14x216
1110 (÷15) OFF*15x210 15x211 15x212 15x213 15x214 15x215 15x216
1111 (÷16) OFF*16x210 16x211 16x212 16x213 16x214 16x215 16x216
* Denotes the default value out of reset.This value should be used to disable the RTI to ensure future backwards compatibility.
Chapter 5 Clocks and Reset Generator (CRGV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
190 Freescale Semiconductor
5.3.2.9 CRG COP Control Register (COPCTL)
This register controls the COP (computer operating properly) watchdog.
Read: anytime
Write: WCOP, CR2, CR1, CR0: once in user mode, anytime in special mode
Write: RSBCK: once
Module Base + 0x0008
76543210
RWCOP RSBCK 000
CR2 CR1 CR0
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 5-12. CRG COP Control Register (COPCTL)
Table 5-8. COPCTL Field Descriptions
Field Description
7
WCOP Window COP Mode Bit When set, a write to the ARMCOP register must occur in the last 25% of the selected
period. A write during the first 75% of the selected period will reset the part. As long as all writes occur during
this window, 0x0055 can be written as often as desired. As soon as 0x00AA is written after the 0x0055, the
time-out logic restarts and the user must wait until the next window before writing to ARMCOP. Table 5-9 shows
the exact duration of this window for the seven available COP rates.
0 Normal COP operation
1 Window COP operation
6
RSBCK COP and RTI Stop in Active BDM Mode Bit
0 Allows the COP and RTI to keep running in active BDM mode.
1 Stops the COP and RTI counters whenever the part is in active BDM mode.
2:0
CR[2:0] COP Watchdog Timer Rate Select — These bits select the COP time-out rate (see Table 5-9). The COP
time-outperiod is OSCCLK period divided by CR[2:0] value.Writing a nonzerovaluetoCR[2:0]enables the COP
counter and starts the time-out period. A COP counter time-out causes a system reset. This can be avoided by
periodically (before time-out) reinitializing the COP counter via the ARMCOP register.
Table 5-9. COP Watchdog Rates1
1OSCCLK cycles are referenced from the previous COP time-out reset
(writing 0x0055/0x00AA to the ARMCOP register)
CR2 CR1 CR0 OSCCLK
Cycles to Time Out
0 0 0 COP disabled
001 2
14
010 2
16
011 2
18
100 2
20
101 2
22
110 2
23
111 2
24
Chapter 5 Clocks and Reset Generator (CRGV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 191
5.3.2.10 Reserved Register (FORBYP)
NOTE
This reserved register is designed for factory test purposes only, and is not
intended for general user access. Writing to this register when in special
modes can alter the CRG’s functionality.
Read: always read 0x0000 except in special modes
Write: only in special modes
5.3.2.11 Reserved Register (CTCTL)
NOTE
This reserved register is designed for factory test purposes only, and is not
intended for general user access. Writing to this register when in special test
modes can alter the CRG’s functionality.
Read: always read 0x0080 except in special modes
Write: only in special modes
Module Base + 0x0009
76543210
R00000000
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 5-13. Reserved Register (FORBYP)
Module Base + 0x000A
76543210
R00000000
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 5-14. Reserved Register (CTCTL)
Chapter 5 Clocks and Reset Generator (CRGV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
192 Freescale Semiconductor
5.3.2.12 CRG COP Timer Arm/Reset Register (ARMCOP)
This register is used to restart the COP time-out period.
Read: always reads 0x0000
Write: anytime
When the COP is disabled (CR[2:0] = “000”) writing to this register has no effect.
When the COP is enabled by setting CR[2:0] nonzero, the following applies:
Writing any value other than 0x0055 or 0x00AA causes a COP reset. To restart the COP time-out
period you must write 0x0055 followed by a write of 0x00AA. Other instructions may be executed
between these writes but the sequence (0x0055, 0x00AA) must be completed prior to COP end of
time-out period to avoid a COP reset. Sequences of 0x0055 writes or sequences of 0x00AA writes
are allowed. When the WCOP bit is set, 0x0055 and 0x00AA writes must be done in the last 25%
of the selected time-out period; writing any value in the first 75% of the selected period will cause
a COP reset.
5.4 Functional Description
This section gives detailed informations on the internal operation of the design.
5.4.1 Phase Locked Loop (PLL)
The PLL is used to run the MCU from a different time base than the incoming OSCCLK. For increased
flexibility, OSCCLK can be divided in a range of 1 to 16 to generate the reference frequency. This offers
a finer multiplication granularity. The PLL can multiply this reference clock by a multiple of 2, 4, 6,...
126,128 based on the SYNR register.
CAUTION
Although it is possible to set the two dividers to command a very high clock
frequency, do not exceed the specified bus frequency limit for the MCU.
If (PLLSEL = 1), Bus Clock = PLLCLK / 2
Module Base + 0x000B
76543210
R00000000
W Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Reset 0 0 0 00000
Figure 5-15. ARMCOP Register Diagram
PLLCLK 2 OSCCLK SYNR 1+[]
REFDV 1+[]
-----------------------------------
××=
Chapter 5 Clocks and Reset Generator (CRGV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 193
The PLL is a frequency generator that operates in either acquisition mode or tracking mode, depending on
the difference between the output frequency and the target frequency. The PLL can change between
acquisition and tracking modes either automatically or manually.
The VCO has a minimum operating frequency, which corresponds to the self-clock mode frequency fSCM.
Figure 5-16. PLL Functional Diagram
5.4.1.1 PLL Operation
The oscillator output clock signal (OSCCLK) is fed through the reference programmable divider and is
divided in a range of 1 to 16 (REFDV+1) to output the reference clock. The VCO output clock, (PLLCLK)
is fed back through the programmable loop divider and is divided in a range of 2 to 128 in increments of
[2 x (SYNR +1)] to output the feedback clock. See Figure 5-16.
The phase detector then compares the feedback clock, with the reference clock. Correction pulses are
generated based on the phase difference between the two signals. The loop filter then slightly alters the DC
voltage on the external filter capacitor connected to XFC pin, based on the width and direction of the
correction pulse. The filter can make fast or slow corrections depending on its mode, as described in the
next subsection. The values of the external filter network and the reference frequency determine the speed
of the corrections and the stability of the PLL.
5.4.1.2 Acquisition and Tracking Modes
The lock detector compares the frequencies of the feedback clock, and the reference clock. Therefore, the
speed of the lock detector is directly proportional to the final reference frequency. The circuit determines
the mode of the PLL and the lock condition based on this comparison.
REDUCED
CONSUMPTION
OSCILLATOR
EXTAL
XTAL
OSCCLK
PLLCLK
REFERENCE
PROGRAMMABLE
DIVIDER PDET
PHASE
DETECTOR
REFDV <3:0>
LOOP
PROGRAMMABLE
DIVIDER
SYN <5:0>
CPUMP VCO
LOCK
LOOP
FILTER
XFC
PIN
UP
DOWN
LOCK
DETECTOR
REFERENCE
FEEDBACK
VDDPLL
VDDPLL/VSSPLL
CRYSTAL
MONITOR
VDDPLL/VSSPLL
VDD/VSS
supplied by:
Chapter 5 Clocks and Reset Generator (CRGV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
194 Freescale Semiconductor
The PLL filter can be manually or automatically configured into one of two possible operating modes:
Acquisition mode
In acquisition mode, the filter can make large frequency corrections to the VCO. This mode is used
at PLL start-up or when the PLL has suffered a severe noise hit and the VCO frequency is far off
the desired frequency. When in acquisition mode, the TRACK status bit is cleared in the CRGFLG
register.
Tracking mode
In tracking mode, the filter makes only small corrections to the frequency of the VCO. PLL jitter
is much lower in tracking mode, but the response to noise is also slower. The PLL enters tracking
mode when the VCO frequency is nearly correct and the TRACK bit is set in the CRGFLG register.
The PLL can change the bandwidth or operational mode of the loop filter manually or automatically.
In automatic bandwidth control mode (AUTO = 1), the lock detector automatically switches between
acquisition and tracking modes. Automatic bandwidth control mode also is used to determine when the
PLL clock (PLLCLK) is safe to use as the source for the system and core clocks. If PLL LOCK interrupt
requests are enabled, the software can wait for an interrupt request and then check the LOCK bit. If CPU
interrupts are disabled, software can poll the LOCK bit continuously (during PLL start-up, usually) or at
periodic intervals. In either case, only when the LOCK bit is set, is the PLLCLK clock safe to use as the
source for the system and core clocks. If the PLL is selected as the source for the system and core clocks
and the LOCK bit is clear, the PLL has suffered a severe noise hit and the software must take appropriate
action, depending on the application.
The following conditions apply when the PLL is in automatic bandwidth control mode (AUTO = 1):
The TRACK bit is a read-only indicator of the mode of the filter.
The TRACK bit is set when the VCO frequency is within a certain tolerance, trk, and is clear when
the VCO frequency is out of a certain tolerance, unt.
The LOCK bit is a read-only indicator of the locked state of the PLL.
The LOCK bit is set when the VCO frequency is within a certain tolerance, Lock, and is cleared
when the VCO frequency is out of a certain tolerance, unl.
CPU interrupts can occur if enabled (LOCKIE = 1) when the lock condition changes, toggling the
LOCK bit.
The PLL can also operate in manual mode (AUTO = 0). Manual mode is used by systems that do not
require an indicator of the lock condition for proper operation. Such systems typically operate well below
the maximum system frequency (fsys) and require fast start-up. The following conditions apply when in
manual mode:
ACQ is a writable control bit that controls the mode of the filter. Before turning on the PLL in
manual mode, the ACQ bit should be asserted to configure the filter in acquisition mode.
After turning on the PLL by setting the PLLON bit software must wait a given time (tacq) before
entering tracking mode (ACQ = 0).
After entering tracking mode software must wait a given time (tal) before selecting the PLLCLK
as the source for system and core clocks (PLLSEL = 1).
Chapter 5 Clocks and Reset Generator (CRGV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 195
5.4.2 System Clocks Generator
Figure 5-17. System Clocks Generator
The clock generator creates the clocks used in the MCU (see Figure 5-17). The gating condition placed on
top of the individual clock gates indicates the dependencies of different modes (stop, wait) and the setting
of the respective configuration bits.
The peripheral modules use the bus clock. Some peripheral modules also use the oscillator clock. The
memory blocks use the bus clock. If the MCU enters self-clock mode (see Section 5.4.7.2, “Self-Clock
Mode”), oscillator clock source is switched to PLLCLK running at its minimum frequency fSCM. The bus
clock is used to generate the clock visible at the ECLK pin. The core clock signal is the clock for the CPU.
The core clock is twice the bus clock as shown in Figure 5-18. But note that a CPU cycle corresponds to
one bus clock.
PLL clock mode is selected with PLLSEL bit in the CLKSEL register. When selected, the PLL output
clock drives SYSCLK for the main system including the CPU and peripherals. The PLL cannot be turned
off by clearing the PLLON bit, if the PLL clock is selected. When PLLSEL is changed, it takes a maximum
OSCILLATOR
PHASE
LOCK
LOOP
EXTAL
XTAL
SYSCLK
RTI
OSCCLK
PLLCLK
CLOCK PHASE
GENERATOR
Bus Clock
Clock
Monitor
1
0
PLLSEL or SCM
÷2
Core Clock
COP
Oscillator
Oscillator
= Clock Gate
Gating
Condition
WAIT(CWAI,SYSWAI),
STOP
WAIT(RTIWAI),
STOP(PSTP,PRE),
RTI enable
WAIT(COPWAI),
STOP(PSTP,PCE),
COP enable
WAIT(SYSWAI),
STOP
STOP(PSTP)
1
0
SCM
WAIT(SYSWAI),
STOP
Clock
Clock
(running during
Pseudo-Stop Mode
Chapter 5 Clocks and Reset Generator (CRGV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
196 Freescale Semiconductor
of 4 OSCCLK plus 4 PLLCLK cycles to make the transition. During the transition, all clocks freeze and
CPU activity ceases.
Figure 5-18. Core Clock and Bus Clock Relationship
5.4.3 Clock Monitor (CM)
If no OSCCLK edges are detected within a certain time, the clock monitor within the oscillator block
generates a clock monitor fail event. The CRGV4 then asserts self-clock mode or generates a system reset
depending on the state of SCME bit. If the clock monitor is disabled or the presence of clocks is detected
no failure is indicated by the oscillator block.The clock monitor function is enabled/disabled by the CME
control bit.
5.4.4 Clock Quality Checker
The clock monitor performs a coarse check on the incoming clock signal. The clock quality checker
provides a more accurate check in addition to the clock monitor.
A clock quality check is triggered by any of the following events:
Power-on reset (POR)
Low voltage reset (LVR)
Wake-up from full stop mode (exit full stop)
Clock monitor fail indication (CM fail)
A time window of 50000 VCO clock cycles1 is called check window.
A number greater equal than 4096 rising OSCCLK edges within a check window is called osc ok. Note that
osc ok immediately terminates the current check window. See Figure 5-19 as an example.
1. VCO clock cycles are generated by the PLL when running at minimum frequency fSCM.
CORE CLOCK:
BUS CLOCK / ECLK
Chapter 5 Clocks and Reset Generator (CRGV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 197
Figure 5-19. Check Window Example
The sequence for clock quality check is shown in Figure 5-20.
Figure 5-20. Sequence for Clock Quality Check
NOTE
Remember that in parallel to additional actions caused by self-clock mode
or clock monitor reset1 handling the clock quality checker continues to
check the OSCCLK signal.
1. A Clock Monitor Reset will always set the SCME bit to logical’1’
12 49999 50000
VCO
clock
check window
12345
4095
4096
3
OSCCLK
osc ok
check window
osc ok
?
SCM
active? Switch to OSCCLK
Exit SCM
Clock OK
num=0
num<50
?
num=num+1
yes
no
yes
SCME=1
?
no
Enter SCM
SCM
active?
yes
Clock Monitor Reset
no
yes
no
num=50
yes
no
POR exit full stop
CM fail
LVR
Chapter 5 Clocks and Reset Generator (CRGV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
198 Freescale Semiconductor
NOTE
The clock quality checker enables the PLL and the voltage regulator
(VREG) anytime a clock check has to be performed. An ongoing clock
quality check could also cause a running PLL (fSCM) and an active VREG
during pseudo-stop mode or wait mode
5.4.5 Computer Operating Properly Watchdog (COP)
Figure 5-21. Clock Chain for COP
The COP (free running watchdog timer) enables the user to check that a program is running and
sequencing properly. The COP is disabled out of reset. When the COP is being used, software is
responsible for keeping the COP from timing out. If the COP times out it is an indication that the software
is no longer being executed in the intended sequence; thus a system reset is initiated (see Section 5.5.2,
“Computer Operating Properly Watchdog (COP) Reset).” The COP runs with a gated OSCCLK (see
Section Figure 5-21., “Clock Chain for COP”). Three control bits in the COPCTL register allow selection
of seven COP time-out periods.
When COP is enabled, the program must write 0x0055 and 0x00AA (in this order) to the ARMCOP
register during the selected time-out period. As soon as this is done, the COP time-out period is restarted.
If the program fails to do this and the COP times out, the part will reset. Also, if any value other than
0x0055 or 0x00AA is written, the part is immediately reset.
Windowed COP operation is enabled by setting WCOP in the COPCTL register. In this mode, writes to
the ARMCOP register to clear the COP timer must occur in the last 25% of the selected time-out period.
A premature write will immediately reset the part.
If PCE bit is set, the COP will continue to run in pseudo-stop mode.
OSCCLK
CR[2:0]
COP TIMEOUT
0:0:0
0:0:1
0:1:0
0:1:1
1:0:0
1:0:1
1:1:0
1:1:1
÷ 4
÷ 4
÷ 2
÷ 4
÷ 2
÷
16384
÷
4
CR[2:0]
= Clock Gate
WAIT(COPWAI),
STOP(PSTP,PCE),
COP enable
gating condition
Chapter 5 Clocks and Reset Generator (CRGV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 199
5.4.6 Real-Time Interrupt (RTI)
The RTI can be used to generate a hardware interrupt at a fixed periodic rate. If enabled (by setting
RTIE=1), this interrupt will occur at the rate selected by the RTICTL register. The RTI runs with a gated
OSCCLK (see Section Figure 5-22., “Clock Chain for RTI”). At the end of the RTI time-out period the
RTIF flag is set to 1 and a new RTI time-out period starts immediately.
A write to the RTICTL register restarts the RTI time-out period.
If the PRE bit is set, the RTI will continue to run in pseudo-stop mode.
.
Figure 5-22. Clock Chain for RTI
5.4.7 Modes of Operation
5.4.7.1 Normal Mode
The CRGV4 block behaves as described within this specification in all normal modes.
5.4.7.2 Self-Clock Mode
The VCO has a minimum operating frequency, fSCM. If the external clock frequency is not available due
to a failure or due to long crystal start-up time, the bus clock and the core clock are derived from the VCO
OSCCLK
RTR[6:4]
0:0:0
0:0:1
0:1:0
0:1:1
1:0:0
1:0:1
1:1:0
1:1:1
÷ 2
÷ 2
÷ 2
÷ 2
÷ 2
÷ 2
COUNTER (RTR[3:0])
4-BIT MODULUS
÷ 1024
RTI TIMEOUT
= Clock Gate
WAIT(RTIWAI),
STOP(PSTP,PRE),
RTI enable
gating condition
Chapter 5 Clocks and Reset Generator (CRGV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
200 Freescale Semiconductor
running at minimum operating frequency; this mode of operation is called self-clock mode. This requires
CME = 1 and SCME = 1. If the MCU was clocked by the PLL clock prior to entering self-clock mode, the
PLLSEL bit will be cleared. If the external clock signal has stabilized again, the CRG will automatically
select OSCCLK to be the system clock and return to normal mode. See Section 5.4.4, “Clock Quality
Checker” for more information on entering and leaving self-clock mode.
NOTE
In order to detect a potential clock loss, the CME bit should be always
enabled (CME=1).
If CME bit is disabled and the MCU is configured to run on PLL clock
(PLLCLK), a loss of external clock (OSCCLK) will not be detected and will
cause the system clock to drift towards the VCO’s minimum frequency
fSCM. As soon as the external clock is available again the system clock
ramps up to its PLL target frequency. If the MCU is running on external
clock any loss of clock will cause the system to go static.
5.4.8 Low-Power Operation in Run Mode
The RTI can be stopped by setting the associated rate select bits to 0.
The COP can be stopped by setting the associated rate select bits to 0.
5.4.9 Low-Power Operation in Wait Mode
The WAI instruction puts the MCU in a low power consumption stand-by mode depending on setting of
the individual bits in the CLKSEL register. All individual wait mode configuration bits can be superposed.
This provides enhanced granularity in reducing the level of power consumption during wait mode.
Table 5-10 lists the individual configuration bits and the parts of the MCU that are affected in wait mode.
After executing the WAI instruction the core requests the CRG to switch MCU into wait mode. The CRG
then checks whether the PLLWAI, CWAI and SYSWAI bits are asserted (see Figure 5-23). Depending on
the configuration the CRG switches the system and core clocks to OSCCLK by clearing the PLLSEL bit,
disables the PLL, disables the core clocks and finally disables the remaining system clocks. As soon as all
clocks are switched off wait mode is active.
Table 5-10. MCU Configuration During Wait Mode
PLLWAI CWAI SYSWAI RTIWAI COPWAI ROAWAI
PLL stopped —————
Core stopped stopped
System stopped
RTI stopped
COP ————stopped
Oscillator —————reduced1
1Refer to oscillator block description for availability of a reduced oscillator amplitude.
Chapter 5 Clocks and Reset Generator (CRGV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 201
Figure 5-23. Wait Mode Entry/Exit Sequence
Enter
Wait Mode
PLLWAI=1
?
Exit Wait w.
CMRESET
Exit Wait w.
ext.RESET
Exit
Wait Mode
Enter
SCM
Exit
Wait Mode
Core req’s
Wait Mode.
CWAI or
SYSWAI=1
?
SYSWAI=1
?
Clear
PLLSEL,
Disable PLL
Disable
core clocks
Disable
system clocks CME=1
?
INT
?
CM fail
?
SCME=1
?
SCMIE=1
?
Continue w.
normal OP
no
no
no
no
no
no
no
yes
yes
yes
yes
yes
no
yes
yes
yes
Wait Mode left
due to external
reset
Generate
SCM Interrupt
(Wakeup from Wait) SCM=1
?
Enter
SCM
no
yes
Chapter 5 Clocks and Reset Generator (CRGV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
202 Freescale Semiconductor
There are five different scenarios for the CRG to restart the MCU from wait mode:
External reset
Clock monitor reset
COP reset
Self-clock mode interrupt
Real-time interrupt (RTI)
If the MCU gets an external reset during wait mode active, the CRG asynchronously restores all
configuration bits in the register space to its default settings and starts the reset generator. After completing
the reset sequence processing begins by fetching the normal reset vector. Wait mode is exited and the MCU
is in run mode again.
If the clock monitor is enabled (CME=1) the MCU is able to leave wait mode when loss of
oscillator/external clock is detected by a clock monitor fail. If the SCME bit is not asserted the CRG
generates a clock monitor fail reset (CMRESET). The CRG’s behavior for CMRESET is the same
compared to external reset, but another reset vector is fetched after completion of the reset sequence. If the
SCME bit is asserted the CRG generates a SCM interrupt if enabled (SCMIE=1). After generating the
interrupt the CRG enters self-clock mode and starts the clock quality checker (see Section 5.4.4, “Clock
Quality Checker”). Then the MCU continues with normal operation.If the SCM interrupt is blocked by
SCMIE = 0, the SCMIF flag will be asserted and clock quality checks will be performed but the MCU will
not wake-up from wait mode.
If any other interrupt source (e.g. RTI) triggers exit from wait mode the MCU immediately continues with
normal operation. If the PLL has been powered-down during wait mode the PLLSEL bit is cleared and the
MCU runs on OSCCLK after leaving wait mode. The software must manually set the PLLSEL bit again,
in order to switch system and core clocks to the PLLCLK.
If wait mode is entered from self-clock mode, the CRG will continue to check the clock quality until clock
check is successful. The PLL and voltage regulator (VREG) will remain enabled.
Table 5-11 summarizes the outcome of a clock loss while in wait mode.
Chapter 5 Clocks and Reset Generator (CRGV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 203
Table 5-11. Outcome of Clock Loss in Wait Mode
CME SCME SCMIE CRG Actions
0 X X Clock failure -->
No action, clock loss not detected.
1 0 X Clock failure -->
CRG performs Clock Monitor Reset immediately
1 1 0 Clock failure -->
Scenario 1: OSCCLK recovers prior to exiting Wait Mode.
– MCU remains in Wait Mode,
– VREG enabled,
– PLL enabled,
– SCM activated,
– Start Clock Quality Check,
– Set SCMIF interrupt flag.
Some time later OSCCLK recovers.
– CM no longer indicates a failure,
– 4096 OSCCLK cycles later Clock Quality Check indicates clock o.k.,
– SCM deactivated,
– PLL disabled depending on PLLWAI,
– VREG remains enabled (never gets disabled in Wait Mode).
– MCU remains in Wait Mode.
Some time later either a wakeup interrupt occurs (no SCM interrupt)
– Exit Wait Mode using OSCCLK as system clock (SYSCLK),
– Continue normal operation.
or an External Reset is applied.
– Exit Wait Mode using OSCCLK as system clock,
– Start reset sequence.
Scenario 2: OSCCLK does not recover prior to exiting Wait Mode.
– MCU remains in Wait Mode,
– VREG enabled,
– PLL enabled,
– SCM activated,
– Start Clock Quality Check,
– Set SCMIF interrupt flag,
– Keep performing Clock Quality Checks (could continue infinitely)
while in Wait Mode.
Some time later either a wakeup interrupt occurs (no SCM interrupt)
– Exit Wait Mode in SCM using PLL clock (fSCM) as system clock,
– Continue to perform additional Clock Quality Checks until OSCCLK
is o.k. again.
or an External RESET is applied.
– Exit Wait Mode in SCM using PLL clock (fSCM) as system clock,
– Start reset sequence,
– Continue to perform additional Clock Quality Checks until OSCCLK
is o.k.again.
Chapter 5 Clocks and Reset Generator (CRGV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
204 Freescale Semiconductor
5.4.10 Low-Power Operation in Stop Mode
All clocks are stopped in STOP mode, dependent of the setting of the PCE, PRE and PSTP bit. The
oscillator is disabled in STOP mode unless the PSTP bit is set. All counters and dividers remain frozen but
do not initialize. If the PRE or PCE bits are set, the RTI or COP continues to run in pseudo-stop mode. In
addition to disabling system and core clocks the CRG requests other functional units of the MCU (e.g.
voltage-regulator) to enter their individual power-saving modes (if available). This is the main difference
between pseudo-stop mode and wait mode.
After executing the STOP instruction the core requests the CRG to switch the MCU into stop mode. If the
PLLSEL bit remains set when entering stop mode, the CRG will switch the system and core clocks to
OSCCLK by clearing the PLLSEL bit. Then the CRG disables the PLL, disables the core clock and finally
disables the remaining system clocks. As soon as all clocks are switched off, stop mode is active.
If pseudo-stop mode (PSTP = 1) is entered from self-clock mode the CRG will continue to check the clock
quality until clock check is successful. The PLL and the voltage regulator (VREG) will remain enabled. If
full stop mode (PSTP = 0) is entered from self-clock mode an ongoing clock quality check will be stopped.
A complete timeout window check will be started when stop mode is exited again.
Wake-up from stop mode also depends on the setting of the PSTP bit.
1 1 1 Clock failure -->
– VREG enabled,
– PLL enabled,
– SCM activated,
– Start Clock Quality Check,
– SCMIF set.
SCMIF generates Self-Clock Mode wakeup interrupt.
– Exit Wait Mode in SCM using PLL clock (fSCM) as system clock,
– Continue to perform a additional Clock Quality Checks until OSCCLK
is o.k. again.
Table 5-11. Outcome of Clock Loss in Wait Mode (continued)
CME SCME SCMIE CRG Actions
Chapter 5 Clocks and Reset Generator (CRGV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 205
Figure 5-24. Stop Mode Entry/Exit Sequence
5.4.10.1 Wake-Up from Pseudo-Stop (PSTP=1)
Wake-upfrom pseudo-stop isthesame as wake-upfromwaitmode.Thereare also threedifferentscenarios
for the CRG to restart the MCU from pseudo-stop mode:
External reset
Clock monitor fail
Wake-up interrupt
Exit Stop w.
CMRESET
Exit
Stop Mode
Enter
SCM
Exit
Stop Mode
Core req’s
Stop Mode.
Clear
PLLSEL,
Disable PLL
CME=1
?
INT
?
CM fail
?
SCME=1
?
SCMIE=1
?
Continue w.
normal OP
no
no
no
no
yes
yes
yes
yes
yes
Generate
SCM Interrupt
(Wakeup from Stop)
Enter
Stop Mode
Exit Stop w.
ext.RESET
Wait Mode left
due to external
Clock
OK
?
SCME=1
?
Enter
SCM
yes
no
yes
Exit Stop w.
CMRESET no
no
no PSTP=1
?
INT
?
yesno
yes
Exit
Stop Mode
Exit
Stop Mode
SCM=1
?
Enter
SCM
no
yes
Chapter 5 Clocks and Reset Generator (CRGV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
206 Freescale Semiconductor
If the MCU gets an external reset during pseudo-stop mode active, the CRG asynchronously restores all
configuration bits in the register space to its default settings and starts the reset generator. After completing
the reset sequence processing begins by fetching the normal reset vector. Pseudo-stop mode is exited and
the MCU is in run mode again.
If the clock monitor is enabled (CME = 1) the MCU is able to leave pseudo-stop mode when loss of
oscillator/external clock is detected by a clock monitor fail. If the SCME bit is not asserted the CRG
generates a clock monitor fail reset (CMRESET). The CRG’s behavior for CMRESET is the same
compared to external reset, but another reset vector is fetched after completion of the reset sequence. If the
SCME bit is asserted the CRG generates a SCM interrupt if enabled (SCMIE=1). After generating the
interrupt the CRG enters self-clock mode and starts the clock quality checker (see Section 5.4.4, “Clock
Quality Checker”). Then the MCU continues with normal operation. If the SCM interrupt is blocked by
SCMIE = 0, the SCMIF flag will be asserted but the CRG will not wake-up from pseudo-stop mode.
If any other interrupt source (e.g. RTI) triggers exit from pseudo-stop mode the MCU immediately
continues with normal operation. Because the PLL has been powered-down during stop mode the PLLSEL
bit is cleared and the MCU runs on OSCCLK after leaving stop mode. The software must set the PLLSEL
bit again, in order to switch system and core clocks to the PLLCLK.
Table 5-12 summarizes the outcome of a clock loss while in pseudo-stop mode.
Chapter 5 Clocks and Reset Generator (CRGV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 207
Table 5-12. Outcome of Clock Loss in Pseudo-Stop Mode
CME SCME SCMIE CRG Actions
0 X X Clock failure -->
No action, clock loss not detected.
1 0 X Clock failure -->
CRG performs Clock Monitor Reset immediately
1 1 0 Clock Monitor failure -->
Scenario 1: OSCCLK recovers prior to exiting Pseudo-Stop Mode.
– MCU remains in Pseudo-Stop Mode,
– VREG enabled,
– PLL enabled,
– SCM activated,
– Start Clock Quality Check,
– Set SCMIF interrupt flag.
Some time later OSCCLK recovers.
– CM no longer indicates a failure,
– 4096 OSCCLK cycles later Clock Quality Check indicates clock o.k.,
– SCM deactivated,
– PLL disabled,
– VREG disabled.
– MCU remains in Pseudo-Stop Mode.
Some time later either a wakeup interrupt occurs (no SCM interrupt)
– Exit Pseudo-Stop Mode using OSCCLK as system clock (SYSCLK),
– Continue normal operation.
or an External Reset is applied.
– Exit Pseudo-Stop Mode using OSCCLK as system clock,
– Start reset sequence.
Scenario 2: OSCCLK does not recover prior to exiting Pseudo-Stop Mode.
– MCU remains in Pseudo-Stop Mode,
– VREG enabled,
– PLL enabled,
– SCM activated,
– Start Clock Quality Check,
– Set SCMIF interrupt flag,
– Keep performing Clock Quality Checks (could continue infinitely)
while in Pseudo-Stop Mode.
Some time later either a wakeup interrupt occurs (no SCM interrupt)
– Exit Pseudo-Stop Mode in SCM using PLL clock (fSCM) as system clock
– Continue to perform additional Clock Quality Checks until OSCCLK
is o.k. again.
or an External RESET is applied.
– Exit Pseudo-Stop Mode in SCM using PLL clock (fSCM) as system clock
– Start reset sequence,
– Continue to perform additional Clock Quality Checks until OSCCLK
is o.k.again.
Chapter 5 Clocks and Reset Generator (CRGV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
208 Freescale Semiconductor
5.4.10.2 Wake-up from Full Stop (PSTP=0)
The MCU requires an external interrupt or an external reset in order to wake-up from stop mode.
If the MCU gets an external reset during full stop mode active, the CRG asynchronously restores all
configuration bits in the register space to its default settings and will perform a maximum of 50 clock
check_windows (see Section 5.4.4, “Clock Quality Checker”). After completing the clock quality check
the CRG starts the reset generator. After completing the reset sequence processing begins by fetching the
normal reset vector. Full stop mode is exited and the MCU is in run mode again.
If the MCU is woken-up by an interrupt, the CRG will also perform a maximum of 50 clock
check_windows (see Section 5.4.4, “Clock Quality Checker”). If the clock quality check is successful, the
CRG will release all system and core clocks and will continue with normal operation. If all clock checks
within the timeout-window are failing, the CRG will switch to self-clock mode or generate a clock monitor
reset (CMRESET) depending on the setting of the SCME bit.
Because the PLL has been powered-down during stop mode the PLLSEL bit is cleared and the MCU runs
on OSCCLK after leaving stop mode. The software must manually set the PLLSEL bit again, in order to
switch system and core clocks to the PLLCLK.
NOTE
In full stop mode, the clock monitor is disabled and any loss of clock will
not be detected.
5.5 Resets
This section describes how to reset the CRGV4 and how the CRGV4 itself controls the reset of the MCU.
It explains all special reset requirements. Because the reset generator for the MCU is part of the CRG, this
section also describes all automatic actions that occur during or as a result of individual reset conditions.
The reset values of registers and signals are provided in Section 5.3, “Memory Map and Register
1 1 1 Clock failure -->
– VREG enabled,
– PLL enabled,
– SCM activated,
– Start Clock Quality Check,
– SCMIF set.
SCMIF generates Self-Clock Mode wakeup interrupt.
– Exit Pseudo-Stop Mode in SCM using PLL clock (fSCM) as system clock,
– Continue to perform a additional Clock Quality Checks until OSCCLK
is o.k. again.
Table 5-12. Outcome of Clock Loss in Pseudo-Stop Mode (continued)
CME SCME SCMIE CRG Actions
Chapter 5 Clocks and Reset Generator (CRGV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 209
Definition.” All reset sources are listed in Table 5-13. Refer to the device overview chapter for related
vector addresses and priorities.
The reset sequence is initiated by any of the following events:
Low level is detected at the RESET pin (external reset).
Power on is detected.
Low voltage is detected.
COP watchdog times out.
Clock monitor failure is detected and self-clock mode was disabled (SCME = 0).
Upon detection of any reset event, an internal circuit drives the RESET pin low for 128 SYSCLK cycles
(see Figure 5-25). Because entry into reset is asynchronous it does not require a running SYSCLK.
However, the internal reset circuit of the CRGV4 cannot sequence out of current reset condition without a
running SYSCLK. The number of 128 SYSCLK cycles might be increased by n = 3 to 6 additional
SYSCLK cycles depending on the internal synchronization latency. After 128+n SYSCLK cycles the
RESET pin is released. The reset generator of the CRGV4 waits for additional 64 SYSCLK cycles and
then samples the RESET pin to determine the originating source. Table 5-14 shows which vector will be
fetched.
NOTE
External circuitry connected to the RESET pin should not include a large
capacitance that would interfere with the ability of this signal to rise to a
valid logic 1 within 64 SYSCLK cycles after the low drive is released.
Table 5-13. Reset Summary
Reset Source Local Enable
Power-on Reset None
Low Voltage Reset None
External Reset None
Clock Monitor Reset PLLCTL (CME=1, SCME=0)
COP Watchdog Reset COPCTL (CR[2:0] nonzero)
Table 5-14. Reset Vector Selection
Sampled RESET Pin
(64 Cycles After
Release)
Clock Monitor
Reset Pending COP Reset
Pending Vector Fetch
1 0 0 POR / LVR / External Reset
1 1 X Clock Monitor Reset
1 0 1 COP Reset
0 X X POR / LVR / External Reset
with rise of RESET pin
Chapter 5 Clocks and Reset Generator (CRGV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
210 Freescale Semiconductor
The internal reset of the MCU remains asserted while the reset generator completes the 192 SYSCLK long
reset sequence. The reset generator circuitry always makes sure the internal reset is deasserted
synchronously after completion of the 192 SYSCLK cycles. In case the RESET pin is externally driven
low for more than these 192 SYSCLK cycles (external reset), the internal reset remains asserted too.
Figure 5-25. RESET Timing
5.5.1 Clock Monitor Reset
The CRGV4 generates a clock monitor reset in case all of the following conditions are true:
Clock monitor is enabled (CME=1)
Loss of clock is detected
Self-clock mode is disabled (SCME=0)
The reset event asynchronously forces the configuration registers to their default settings (see Section 5.3,
“Memory Map and Register Definition”). In detail the CME and the SCME are reset to logical ‘1’ (which
doesn’t change the state of the CME bit, because it has already been set). As a consequence, the CRG
immediately enters self-clock mode and starts its internal reset sequence. In parallel the clock quality
check starts. As soon as clock quality check indicates a valid oscillator clock the CRG switches to
OSCCLK and leaves self-clock mode. Because the clock quality checker is running in parallel to the reset
generator, the CRG may leave self-clock mode while completing the internal reset sequence. When the
reset sequence is finished the CRG checks the internally latched state of the clock monitor fail circuit. If a
clock monitor fail is indicated processing begins by fetching the clock monitor reset vector.
5.5.2 Computer Operating Properly Watchdog (COP) Reset
When COP is enabled, the CRG expects sequential write of 0x0055 and 0x00AA (in this order) to the
ARMCOP register during the selected time-out period. As soon as this is done, the COP time-out period
restarts. If the program fails to do this the CRG will generate a reset. Also, if any value other than 0x0055
or 0x00AA is written, the CRG immediately generates a reset. In case windowed COP operation is enabled
) ( ) (
)(
)
SYSCLK
128+n cycles 64 cycles
with nbeing
min 3 / max 6
cycles depending
on internal
synchronization
delay
CRG drives RESET pin low
possibly
SYSCLK
not
running
possibly
RESET
driven low
externally
)(
(
RESET
RESET pin
released
Chapter 5 Clocks and Reset Generator (CRGV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 211
writes (0x0055 or 0x00AA) to the ARMCOP register must occur in the last 25% of the selected time-out
period. A premature write the CRG will immediately generate a reset.
As soon as the reset sequence is completed the reset generator checks the reset condition. If no clock
monitor failure is indicated and the latched state of the COP timeout is true, processing begins by fetching
the COP vector.
5.5.3 Power-On Reset, Low Voltage Reset
The on-chip voltage regulator detects when VDD to the MCU has reached a certain level and asserts
power-on reset or low voltage reset or both. As soon as a power-on reset or low voltage reset is triggered
the CRG performs a quality check on the incoming clock signal. As soon as clock quality check indicates
a valid oscillator clock signal the reset sequence starts using the oscillator clock. If after 50 check windows
the clock quality check indicated a non-valid oscillator clock the reset sequence starts using self-clock
mode.
Figure 5-26 and Figure 5-27 show the power-up sequence for cases when the RESET pin is tied to VDD
and when the RESET pin is held low.
Figure 5-26. RESET Pin Tied to VDD (by a Pull-Up Resistor)
Figure 5-27. RESET Pin Held Low Externally
RESET
Internal POR
128 SYSCLK
64 SYSCLK
Internal RESET
Clock Quality Check
(no Self-Clock Mode)
) (
) (
) (
Clock Quality Check
RESET
Internal POR
Internal RESET
128 SYSCLK
64 SYSCLK
(no Self-Clock Mode)
) (
) (
) (
Chapter 5 Clocks and Reset Generator (CRGV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
212 Freescale Semiconductor
5.6 Interrupts
The interrupts/reset vectors requested by the CRG are listed in Table 5-15. Refer to the device overview
chapter for related vector addresses and priorities.
5.6.1 Real-Time Interrupt
The CRGV4 generates a real-time interrupt when the selected interrupt time period elapses. RTI interrupts
are locally disabled by setting the RTIE bit to 0. The real-time interrupt flag (RTIF) is set to 1 when a
timeout occurs, and is cleared to 0 by writing a 1 to the RTIF bit.
The RTI continues to run during pseudo-stop mode if the PRE bit is set to 1. This feature can be used for
periodic wakeup from pseudo-stop if the RTI interrupt is enabled.
5.6.2 PLL Lock Interrupt
The CRGV4 generates a PLL lock interrupt when the LOCK condition of the PLL has changed, either
from a locked state to an unlocked state or vice versa. Lock interrupts are locally disabled by setting the
LOCKIE bit to 0. The PLL Lock interrupt flag (LOCKIF) is set to1 when the LOCK condition has
changed, and is cleared to 0 by writing a 1 to the LOCKIF bit.
5.6.3 Self-Clock Mode Interrupt
The CRGV4 generates a self-clock mode interrupt when the SCM condition of the system has changed,
either entered or exited self-clock mode. SCM conditions can only change if the self-clock mode enable
bit (SCME) is set to 1. SCM conditions are caused by a failing clock quality check after power-on reset
(POR) or low voltage reset (LVR) or recovery from full stop mode (PSTP = 0) or clock monitor failure.
For details on the clock quality check refer to Section 5.4.4, “Clock Quality Checker. If the clock monitor
is enabled (CME = 1) a loss of external clock will also cause a SCM condition (SCME = 1).
SCM interrupts are locally disabled by setting the SCMIE bit to 0. The SCM interrupt flag (SCMIF) is set
to 1 when the SCM condition has changed, and is cleared to 0 by writing a 1 to the SCMIF bit.
Table 5-15. CRG Interrupt Vectors
Interrupt Source CCR
Mask Local Enable
Real-time interrupt I bit CRGINT (RTIE)
LOCK interrupt I bit CRGINT (LOCKIE)
SCM interrupt I bit CRGINT (SCMIE)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 213
Chapter 6
Pierce Oscillator (S12OSCLCPV1)
6.1 Introduction
The Pierce oscillator (XOSC) module provides a robust, low-noise and low-power clock source. The
module will be operated from the VDDPLL supply rail (2.5 V nominal) and require the minimum number
of external components. It is designed for optimal start-up margin with typical crystal oscillators.
6.1.1 Features
The XOSC will contain circuitry to dynamically control current gain in the output amplitude. This ensures
a signal with low harmonic distortion, low power and good noise immunity.
High noise immunity due to input hysteresis
Low RF emissions with peak-to-peak swing limited dynamically
Transconductance (gm) sized for optimum start-up margin for typical oscillators
Dynamic gain control eliminates the need for external current limiting resistor
Integrated resistor eliminates the need for external bias resistor
Low power consumption:
Operates from 2.5 V (nominal) supply
Amplitude control limits power
Clock monitor
6.1.2 Modes of Operation
Two modes of operation exist:
1. Loop controlled Pierce oscillator
2. External square wave mode featuring also full swing Pierce without internal feedback resistor
Chapter 6 Pierce Oscillator (S12OSCLCPV1)
MC9S12KG128 Data Sheet, Rev. 1.16
214 Freescale Semiconductor
6.1.3 Block Diagram
Figure 6-1 shows a block diagram of the XOSC.
Figure 6-1. XOSC Block Diagram
6.2 External Signal Description
This section lists and describes the signals that connect off chip
6.2.1 VDDPLL and VSSPLL — Operating and Ground Voltage Pins
Theses pins provides operating voltage (VDDPLL) and ground (VSSPLL) for the XOSC circuitry. This
allows the supply voltage to the XOSC to be independently bypassed.
6.2.2 EXTAL and XTAL — Input and Output Pins
These pins provide the interface for either a crystal or a CMOS compatible clock to control the internal
clock generator circuitry. EXTAL is the external clock input or the input to the crystal oscillator amplifier.
XTAL is the output of the crystal oscillator amplifier. The MCU internal system clock is derived from the
EXTAL XTAL
Gain Control
VDDPLL = 2.5 V
Rf
OSCCLK
Monitor_Failure
Clock
Monitor
Peak
Detector
Chapter 6 Pierce Oscillator (S12OSCLCPV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 215
EXTAL input frequency. In full stop mode (PSTP = 0), the EXTAL pin is pulled down by an internal
resistor of typical 200 k.
NOTE
Freescale recommends an evaluation of the application board and chosen
resonator or crystal by the resonator or crystal supplier.
Loop controlled circuit is not suited for overtone resonators and crystals.
Figure 6-2. Loop Controlled Pierce Oscillator Connections (XCLKS = 0)
NOTE
Full swing Pierce circuit is not suited for overtone resonators and crystals
without a careful component selection.
Figure 6-3. Full Swing Pierce Oscillator Connections (XCLKS = 1)
Figure 6-4. External Clock Connections (XCLKS = 1)
MCU
EXTAL
XTAL
VSSPLL
Crystal or
Ceramic Resonator
C2
C1
* Rs can be zero (shorted) when use with higher frequency crystals.
Refer to manufacturer’s data.
MCU
EXTAL
XTAL RS*
RB
VSSPLL
Crystal or
Ceramic Resonator
C2
C1
MCU
EXTAL
XTAL Not Connected
CMOS Compatible
External Oscillator
(VDDPLL Level)
Chapter 6 Pierce Oscillator (S12OSCLCPV1)
MC9S12KG128 Data Sheet, Rev. 1.16
216 Freescale Semiconductor
6.2.3 XCLKS — Input Signal
The XCLKS is an input signal which controls whether a crystal in combination with the internal loop
controlled (low power) Pierce oscillator is used or whether full swing Pierce oscillator/external clock
circuitry is used. Refer to the Device Overview chapter for polarity and sampling conditions of the XCLKS
pin. Table 6-1 lists the state coding of the sampled XCLKS signal.
.
6.3 Memory Map and Register Definition
The CRG contains the registers and associated bits for controlling and monitoring the oscillator module.
6.4 Functional Description
The XOSC module has control circuitry to maintain the crystal oscillator circuit voltage level to an optimal
level which is determined by the amount of hysteresis being used and the maximum oscillation range.
The oscillator block has two external pins, EXTAL and XTAL. The oscillator input pin, EXTAL, is
intended to be connected to either a crystal or an external clock source. The selection of loop controlled
Pierce oscillator or full swing Pierce oscillator/external clock depends on the XCLKS signal which is
sampled during reset. The XTAL pin is an output signal that provides crystal circuit feedback.
A buffered EXTAL signal becomes the internal clock. To improve noise immunity, the oscillator is
powered by the VDDPLL and VSSPLL power supply pins.
6.4.1 Gain Control
A closed loop control system will be utilized whereby the amplifier is modulated to keep the output
waveform sinusoidal and to limit the oscillation amplitude. The output peak to peak voltage will be kept
above twice the maximum hysteresis level of the input buffer. Electrical specification details are provided
in the Electrical Characteristics appendix.
6.4.2 Clock Monitor
The clock monitor circuit is based on an internal RC time delay so that it can operate without any MCU
clocks. If no OSCCLK edges are detected within this RC time delay, the clock monitor indicates failure
which asserts self-clock mode or generates a system reset depending on the state of SCME bit. If the clock
monitor is disabled or the presence of clocks is detected no failure is indicated.The clock monitor function
is enabled/disabled by the CME control bit, described in the CRG block description chapter.
Table 6-1. Clock Selection Based on XCLKS
XCLKS Description
0 Loop controlled Pierce oscillator selected
1 Full swing Pierce oscillator/external clock selected
Chapter 6 Pierce Oscillator (S12OSCLCPV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 217
6.4.3 Wait Mode Operation
During wait mode, XOSC is not impacted.
6.4.4 Stop Mode Operation
XOSC is placed in a static state when the part is in stop mode except when pseudo-stop mode is enabled.
During pseudo-stop mode, XOSC is not impacted.
Chapter 6 Pierce Oscillator (S12OSCLCPV1)
MC9S12KG128 Data Sheet, Rev. 1.16
218 Freescale Semiconductor
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 219
Chapter 7
Analog-to-Digital Converter (ATD10B16CV3)
Block Description
7.1 Introduction
The ATD10B16C is a 16-channel, 10-bit, multiplexed input successive approximation analog-to-digital
converter. Refer to device electical for ATD accuracy.
7.1.1 Features
8-/10-bit resolution
•7µs, 10-bit single conversion time
Sample buffer amplifier
Programmable sample time
Left/right justified, signed/unsigned result data
External trigger control
Conversion completion interrupt generation
Analog input multiplexer for 16 analog input channels
Analog/digital input pin multiplexing
1 to 16 conversion sequence lengths
Continuous conversion mode
Multiple channel scans
Configurable external trigger functionality on any AD channel or additional trigger input. The
additional trigger input can be chip external or internal. Refer to device specification for
availability and connectivity
Configurable location for channel wrap around (when converting multiple channels in a sequence)
7.1.2 Modes of Operation
There is software programmable selection between performing single or continuous conversion on a
single channel or multiple channels.
7.1.3 Block Diagram
Refer to Figure 7-1 for a block diagram of the ATD0B16C block.
Chapter 7 Analog-to-Digital Converter (ATD10B16CV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
220 Freescale Semiconductor
Figure 7-1. ATD10B16C Block Diagram
VRL
AN8 / PAD8
ATD10B16C
Port AD Data Registers
Analog
MUX
Mode and Timing Control
Successive
Approximation
Register (SAR)
Results
ATD 0
ATD 1
ATD 2
ATD 3
ATD 4
ATD 5
ATD 6
ATD 7
and DAC
Sample & Hold
1
1
VRH
VSSA
VDDA
Conversion
Complete Interrupt
+
-
Comparator
Clock
Prescaler
Bus Clock ATD clock
ATD Input Enable Registers
ATD 8
ATD 9
ATD 10
ATD 11
ATD 12
ATD 13
ATD 14
ATD 15
AN7 / PAD7
AN6 / PAD6
AN5 / PAD5
AN4 / PAD4
AN3 / PAD3
AN2 / PAD2
AN1 / PAD1
AN0 / PAD0
AN9 / PAD9
AN10 / PAD10
AN11 / PAD11
AN12 / PAD12
AN13 / PAD13
AN14 / PAD14
AN15 / PAD15
ETRIG
(see device specifi-
cation for availablity)
Chapter 7 Analog-to-Digital Converter (ATD10B16CV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 221
7.2 External Signal Description
This section lists all inputs to the ATD10B16C block.
7.2.1 ANx(x= 15, 14, 13, 12, 11, 10, 9, 8, 7, 6, 5, 4, 3, 2, 1, 0) Analog Input
Channel x Pins
This pin serves as the analog input channel x. It can also be configured as general-purpose digital input
and/or external trigger for the ATD conversion.
7.2.2 ETRIG — External Trigger Pins
This input can be configured to serve as an external trigger for the ATD conversion.
Refer to device specification for availability and connectivity of this pin.
7.2.3 VRH,V
RL High Reference Voltage Pin, Low Reference Voltage Pin
VRH is the high reference voltage, VRL is the low reference voltage for ATD conversion.
7.2.4 VDDA, VSSA — Analog Circuitry Power Supply Pins
These pins are the power supplies for the analog circuitry of the ATD10B16CV3 block.
7.3 Memory Map and Register Definition
This section provides a detailed description of all registers accessible in the ATD10B16C.
7.3.1 Module Memory Map
Table 7-1 gives an overview of all ATD10B16C registers
Chapter 7 Analog-to-Digital Converter (ATD10B16CV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
222 Freescale Semiconductor
.
NOTE
Register Address = Base Address + Address Offset, where the Base Address
is defined at the MCU level and the Address Offset is defined at the module
level.
Table 7-1. ATD10B16CV3 Memory Map
Address Offset Use Access
0x0000 ATD Control Register 0 (ATDCTL0) R/W
0x0001 ATD Control Register 1 (ATDCTL1) R/W
0x0002 ATD Control Register 2 (ATDCTL2) R/W
0x0003 ATD Control Register 3 (ATDCTL3) R/W
0x0004 ATD Control Register 4 (ATDCTL4) R/W
0x0005 ATD Control Register 5 (ATDCTL5) R/W
0x0006 ATD Status Register 0 (ATDSTAT0) R/W
0x0007 Unimplemented
0x0008 ATD Test Register 0 (ATDTEST0)1
1ATDTEST0 is intended for factory test purposes only.
R
0x0009 ATD Test Register 1 (ATDTEST1) R/W
0x000A ATD Status Register 2 (ATDSTAT2) R
0x000B ATD Status Register 1 (ATDSTAT1) R
0x000C ATD Input Enable Register 0 (ATDDIEN0) R/W
0x000D ATD Input Enable Register 1 (ATDDIEN1) R/W
0x000E Port Data Register 0 (PORTAD0) R
0x000F Port Data Register 1 (PORTAD1) R
0x0010, 0x0011 ATD Result Register 0 (ATDDR0H, ATDDR0L) R/W
0x0012, 0x0013 ATD Result Register 1 (ATDDR1H, ATDDR1L) R/W
0x0014, 0x0015 ATD Result Register 2 (ATDDR2H, ATDDR2L) R/W
0x0016, 0x0017 ATD Result Register 3 (ATDDR3H, ATDDR3L) R/W
0x0018, 0x0019 ATD Result Register 4 (ATDDR4H, ATDDR4L) R/W
0x001A, 0x001B ATD Result Register 5 (ATDDR5H, ATDDR5L) R/W
0x001C, 0x001D ATD Result Register 6 (ATDDR6H, ATDDR6L) R/W
0x001E, 0x001F ATD Result Register 7 (ATDDR7H, ATDDR7L) R/W
0x0020, 0x0021 ATD Result Register 8 (ATDDR8H, ATDDR8L) R/W
0x0022, 0x0023 ATD Result Register 9 (ATDDR9H, ATDDR9L) R/W
0x0024, 0x0025 ATD Result Register 10 (ATDDR10H, ATDDR10L) R/W
0x0026, 0x0027 ATD Result Register 11 (ATDDR11H, ATDDR11L) R/W
0x0028, 0x0029 ATD Result Register 12 (ATDDR12H, ATDDR12L) R/W
0x002A, 0x002B ATD Result Register 13 (ATDDR13H, ATDDR13L) R/W
0x002C, 0x002D ATD Result Register 14 (ATDDR14H, ATDDR14L) R/W
0x002E, 0x002F ATD Result Register 15 (ATDDR15H, ATDDR15L) R/W
Chapter 7 Analog-to-Digital Converter (ATD10B16CV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 223
7.3.2 Register Descriptions
This section describes in address order all the ATD10B16C registers and their individual bits.
Register
Name Bit 7 6 5 4 3 2 1 Bit 0
0x0000
ATDCTL0 R0000
WRAP3 WRAP2 WRAP1 WRAP0
W
0x0001
ATDCTL1 RETRIGSEL 000
ETRIGCH3 ETRIGCH2 ETRIGCH1 ETRIGCH0
W
0x0002
ATDCTL2 RADPU AFFC AWAI ETRIGLE ETRIGP ETRIGE ASCIE ASCIF
W
0x0003
ATDCTL3 R0 S8C S4C S2C S1C FIFO FRZ1 FRZ0
W
0x0004
ATDCTL4 RSRES8 SMP1 SMP0 PRS4 PRS3 PRS2 PRS1 PRS0
W
0x0005
ATDCTL5 RDJM DSGN SCAN MULT CD CC CB CA
W
0x0006
ATDSTAT0 RSCF 0ETORF FIFOR CC3 CC2 CC1 CC0
W
0x0007
Unimplemented R
W
0x0008
ATDTEST0 R Unimplemented
W
0x0009
ATDTEST1 R Unimplemented SC
W
0x000A
ATDSTAT2 R CCF15 CCF14 CCF13 CCF12 CCF11 CCF10 CCF9 CCF8
W
0x000B
ATDSTAT1 R CCF7 CCF6 CCF5 CCF4 CCF3 CCF2 CCF1 CCF0
W
0x000C
ATDDIEN0 RIEN15 IEN14 IEN13 IEN12 IEN11 IEN10 IEN9 IEN8
W
= Unimplemented or Reserved u = Unaffected
Figure 7-2. ATD Register Summary
Chapter 7 Analog-to-Digital Converter (ATD10B16CV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
224 Freescale Semiconductor
7.3.2.1 ATD Control Register 0 (ATDCTL0)
Writes to this register will abort current conversion sequence but will not start a new sequence.
Read: Anytime
Write: Anytime
0x000D
ATDDIEN1 RIEN7 IEN6 IEN5 IEN4 IEN3 IEN2 IEN1 IEN0
W
0x000E
PORTAD0 R PTAD15 PTAD14 PTAD13 PTAD12 PTAD11 PTAD10 PTAD9 PTAD8
W
0x000F
PORTAD1 R PTAD7 PTAD6 PTAD5 PTAD4 PTAD3 PTAD2 PTAD1 PTAD0
W
R BIT 9 MSB
BIT 7 MSB BIT 8
BIT 6 BIT 7
BIT 5 BIT 6
BIT 4 BIT 5
BIT 3 BIT 4
BIT 2 BIT 3
BIT 1 BIT 2
BIT 0
0x0010–0x002F
ATDDRxH–
ATDDRxL
W
R BIT 1
uBIT 0
u0
00
00
00
00
00
0
W
76543210
R0000
WRAP3 WRAP2 WRAP1 WRAP0
W
Reset 0 0 0 01111
= Unimplemented or Reserved
Figure 7-3. ATD Control Register 0 (ATDCTL0)
Table 7-2. ATDCTL0 Field Descriptions
Field Description
3:0
WRAP[3:0] Wrap Around Channel Select Bits — These bits determine the channel for wrap around when doing
multi-channel conversions. The coding is summarized in Table 7-3.
Register
Name Bit 7 6 5 4 3 2 1 Bit 0
= Unimplemented or Reserved u = Unaffected
Figure 7-2. ATD Register Summary (continued)
Chapter 7 Analog-to-Digital Converter (ATD10B16CV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 225
7.3.2.2 ATD Control Register 1 (ATDCTL1)
Writes to this register will abort current conversion sequence but will not start a new sequence.
Read: Anytime
Write: Anytime
Table 7-3. Multi-Channel Wrap Around Coding
WRAP3 WRAP2 WRAP1 WRAP0 Multiple Channel Conversions
(MULT = 1) Wrap Around to AN0
after Converting
0 0 0 0 Reserved
0001 AN1
0010 AN2
0011 AN3
0100 AN4
0101 AN5
0110 AN6
0111 AN7
1000 AN8
1001 AN9
1 0 1 0 AN10
1 0 1 1 AN11
1 1 0 0 AN12
1 1 0 1 AN13
1 1 1 0 AN14
1 1 1 1 AN15
76543210
RETRIGSEL 000
ETRIGCH3 ETRIGCH2 ETRIGCH1 ETRIGCH0
W
Reset 0 0 0 01111
= Unimplemented or Reserved
Figure 7-4. ATD Control Register 1 (ATDCTL1)
Table 7-4. ATDCTL1 Field Descriptions
Field Description
7
ETRIGSEL External Trigger Source Select — This bit selects the external trigger source to be either one of the AD
channels or the ETRIG inputs. See device specification for availability and connectivity of ETRIG input. If
ETRIG input option is not available, writing a 1 to ETRISEL only sets the bit but has no effect, that means one
of the AD channels (selected by ETRIGCH[3:0]) remains the source for external trigger. The coding is
summarized in Table 7-5.
3:0
ETRIGCH[3:0] External Trigger Channel Select These bitsselectone of the ADchannels inputs as source fortheexternal
trigger. The coding is summarized in Table 7-5.
Chapter 7 Analog-to-Digital Converter (ATD10B16CV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
226 Freescale Semiconductor
7.3.2.3 ATD Control Register 2 (ATDCTL2)
This register controls power down, interrupt and external trigger. Writes to this register will abort current
conversion sequence but will not start a new sequence.
Read: Anytime
Write: Anytime
Table 7-5. External Trigger Channel Select Coding
ETRIGSEL ETRIGCH3 ETRIGCH2 ETRIGCH1 ETRIGCH0 External Trigger Source
0 0 0 0 0 AN0
0 0 0 0 1 AN1
0 0 0 1 0 AN2
0 0 0 1 1 AN3
0 0 1 0 0 AN4
0 0 1 0 1 AN5
0 0 1 1 0 AN6
0 0 1 1 1 AN7
0 1 0 0 0 AN8
0 1 0 0 1 AN9
0 1 0 1 0 AN10
0 1 0 1 1 AN11
0 1 1 0 0 AN12
0 1 1 0 1 AN13
0 1 1 1 0 AN14
0 1 1 1 1 AN15
1 x x x x ETRIG
76543210
RADPU AFFC AWAI ETRIGLE ETRIGP ETRIGE ASCIE ASCIF
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 7-5. ATD Control Register 2 (ATDCTL2)
Chapter 7 Analog-to-Digital Converter (ATD10B16CV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 227
Table 7-6. ATDCTL2 Field Descriptions
Field Description
7
ADPU ATD Power Down This bit provides on/off control over the ATD10B16C block allowing reduced MCU power
consumption. Because analog electronic is turned off when powered down, the ATD requires a recovery time
period after ADPU bit is enabled.
0 Power down ATD
1 Normal ATD functionality
6
AFFC ATD Fast Flag Clear All
0 ATD flag clearing operates normally (read the status register ATDSTAT1 before reading the result register
to clear the associate CCF flag).
1 Changes all ATD conversion complete flags to a fast clear sequence. Any access to a result register will
cause the associate CCF flag to clear automatically.
5
AWAI ATD Power Down in Wait Mode — When entering Wait Mode this bit provides on/off control over the
ATD10B16CblockallowingreducedMCU power.Becauseanalogelectronic is turned off when powereddown,
the ATD requires a recovery time period after exit from Wait mode.
0 ATD continues to run in Wait mode
1 Halt conversion and power down ATD during Wait mode
After exiting Wait mode with an interrupt conversion will resume. But due to the recovery time the result of
this conversion should be ignored.
4
ETRIGLE External Trigger Level/Edge Control — This bit controls the sensitivity of the external trigger signal. See
Table 7-7 for details.
3
ETRIGP External Trigger Polarity — This bit controls the polarity of the external trigger signal. See Table 7-7 for
details.
2
ETRIGE External Trigger Mode Enable Thisbit enablestheexternaltrigger onone ofthe ADchannelsor theETRIG
input as described in Table 7-5. If external trigger source is one of the AD channels, the digital input buffer of
this channel is enabled. The external trigger allows to synchronize the start of conversion with external events.
0 Disable external trigger
1 Enable external trigger
Note: If using one of the ATD channel as external trigger (ETRIGSEL = 0) the conversion results for this
channel have no meaning while external trigger mode is enabled.
1
ASCIE ATD Sequence Complete Interrupt Enable
0 ATD Sequence Complete interrupt requests are disabled.
1 ATD Interrupt will be requested whenever ASCIF = 1 is set.
0
ASCIF ATD Sequence Complete Interrupt Flag — If ASCIE = 1 the ASCIF flag equals the SCF flag (see
Section 7.3.2.7, “ATD Status Register 0 (ATDSTAT0)”), else ASCIF reads zero. Writes have no effect.
0 No ATD interrupt occurred
1 ATD sequence complete interrupt pending
Table 7-7. External Trigger Configurations
ETRIGLE ETRIGP External Trigger Sensitivity
0 0 Falling Edge
0 1 Ring Edge
1 0 Low Level
1 1 High Level
Chapter 7 Analog-to-Digital Converter (ATD10B16CV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
228 Freescale Semiconductor
7.3.2.4 ATD Control Register 3 (ATDCTL3)
This register controls the conversion sequence length, FIFO for results registers and behavior in Freeze
Mode. Writes to this register will abort current conversion sequence but will not start a new sequence.
Read: Anytime
Write: Anytime
76543210
R0 S8C S4C S2C S1C FIFO FRZ1 FRZ0
W
Reset 0 0 1 00000
= Unimplemented or Reserved
Figure 7-6. ATD Control Register 3 (ATDCTL3)
Table 7-8. ATDCTL3 Field Descriptions
Field Description
6
S8C Conversion Sequence Length This bit controls the number of conversions per sequence. Table 7-9 shows
allcombinations. At reset,S4C is setto 1 (sequencelengthis 4).Thisis to maintainsoftwarecontinuitytoHC12
Family.
5
S4C Conversion Sequence Length This bit controls the number of conversions per sequence. Table 7-9 shows
allcombinations. At reset,S4C is setto 1 (sequencelengthis 4).Thisis to maintainsoftwarecontinuitytoHC12
Family.
4
S2C Conversion Sequence Length This bit controls the number of conversions per sequence. Table 7-9 shows
allcombinations. At reset,S4C is setto 1 (sequencelengthis 4).Thisis to maintainsoftwarecontinuitytoHC12
Family.
3
S1C Conversion Sequence Length This bit controls the number of conversions per sequence. Table 7-9 shows
allcombinations. At reset,S4C is setto 1 (sequencelengthis 4).Thisis to maintainsoftwarecontinuitytoHC12
Family.
Chapter 7 Analog-to-Digital Converter (ATD10B16CV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 229
2
FIFO Result Register FIFO Mode —If this bit is zero (non-FIFO mode), the A/D conversion results map into the
result registers based on the conversion sequence; the result of the first conversion appears in the first result
register, the second result in the second result register, and so on.
If this bit is one (FIFO mode) the conversion counter is not reset at the beginning or ending of a conversion
sequence; sequential conversion results are placed in consecutive result registers. In a continuously scanning
conversion sequence, the result register counter will wrap around when it reaches the end of the result register
file. The conversion counter value (CC3-0 in ATDSTAT0) can be used to determine where in the result register
file, the current conversion result will be placed.
Aborting a conversion or starting a new conversion by write to an ATDCTL register (ATDCTL5-0) clears the
conversion counter even if FIFO=1. So the first result of a new conversion sequence, started by writing to
ATDCTL5, will always be place in the first result register (ATDDDR0). Intended usage of FIFO mode is
continuos conversion (SCAN=1) or triggered conversion (ETRIG=1).
Finally, which result registers holdvaliddatacan be trackedusing the conversioncompleteflags. Fast flag clear
mode may or may not be useful in a particular application to track valid data.
0 Conversion results are placed in the corresponding result register up to the selected sequence length.
1 Conversion results are placed in consecutive result registers (wrap around at end).
1:0
FRZ[1:0] Background Debug Freeze Enable When debugging an application, it is useful in many cases to have the
ATDpause when abreakpoint(FreezeMode) is encountered.These2 bits determinehow theATD will respond
to a breakpoint as shown in Table 7-10. Leakage onto the storage node and comparator reference capacitors
may compromise the accuracy of an immediately frozen conversion depending on the length of the freeze
period.
Table 7-9. Conversion Sequence Length Coding
S8C S4C S2C S1C Number of Conversions
per Sequence
0000 16
0001 1
0010 2
0011 3
0100 4
0101 5
0110 6
0111 7
1000 8
1001 9
1010 10
1011 11
1100 12
1101 13
1110 14
1111 15
Table 7-8. ATDCTL3 Field Descriptions (continued)
Field Description
Chapter 7 Analog-to-Digital Converter (ATD10B16CV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
230 Freescale Semiconductor
Table 7-10. ATD Behavior in Freeze Mode (Breakpoint)
FRZ1 FRZ0 Behavior in Freeze Mode
0 0 Continue conversion
0 1 Reserved
1 0 Finish current conversion, then freeze
1 1 Freeze Immediately
Chapter 7 Analog-to-Digital Converter (ATD10B16CV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 231
7.3.2.5 ATD Control Register 4 (ATDCTL4)
This register selects the conversion clock frequency, the length of the second phase of the sample time and
the resolution of the A/D conversion (i.e., 8-bits or 10-bits). Writes to this register will abort current
conversion sequence but will not start a new sequence.
Read: Anytime
Write: Anytime
76543210
RSRES8 SMP1 SMP0 PRS4 PRS3 PRS2 PRS1 PRS0
W
Reset 0 0 0 00101
Figure 7-7. ATD Control Register 4 (ATDCTL4)
Table 7-11. ATDCTL4 Field Descriptions
Field Description
7
SRES8 A/D Resolution Select — This bit selects the resolution of A/D conversion results as either 8 or 10 bits. The
A/Dconverterhas an accuracy of 10 bits.However,if low resolution is required, the conversioncan be speeded
up by selecting 8-bit resolution.
0 10 bit resolution
1 8 bit resolution
6:5
SMP[1:0] Sample Time Select —These two bits select the length of the second phase of the sample time in units of ATD
conversion clock cycles. Note that the ATD conversion clock period is itself a function of the prescaler value
(bits PRS4-0). The sample time consists of two phases. The first phase is two ATD conversion clock cycles
long and transfers the sample quickly (via the buffer amplifier) onto the A/D machine’s storage node. The
second phase attaches the external analog signal directly to the storage node for final charging and high
accuracy. Table 7-12 lists the lengths available for the second sample phase.
4:0
PRS[4:0] ATD Clock Prescaler — These 5 bits are the binary value prescaler value PRS. The ATD conversion clock
frequency is calculated as follows:
Note: The maximum ATD conversion clock frequency is half the bus clock. The default (after reset) prescaler
value is 5 which results in a default ATD conversion clock frequency that is bus clock divided by 12.
Table 7-13 illustrates the divide-by operation and the appropriate range of the bus clock.
Table 7-12. Sample Time Select
SMP1 SMP0 Length of 2nd Phase of Sample Time
0 0 2 A/D conversion clock periods
0 1 4 A/D conversion clock periods
1 0 8 A/D conversion clock periods
1 1 16 A/D conversion clock periods
ATDclock BusClock[]
PRS 1+[]
-------------------------------- 0.5×=
Chapter 7 Analog-to-Digital Converter (ATD10B16CV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
232 Freescale Semiconductor
Table 7-13. Clock Prescaler Values
Prescale Value Total Divisor
Value Max. Bus Clock1
1Maximum ATD conversion clock frequency is 2 MHz. The maximum allowed bus clock frequency is
shown in this column.
Min. Bus Clock2
2Minimum ATD conversion clock frequency is 500 kHz. The minimum allowed bus clock frequency is
shown in this column.
00000
00001
00010
00011
00100
00101
00110
00111
01000
01001
01010
01011
01100
01101
01110
01111
10000
10001
10010
10011
10100
10101
10110
10111
11000
11001
11010
11011
11100
11101
11110
11111
Divide by 2
Divide by 4
Divide by 6
Divide by 8
Divide by 10
Divide by 12
Divide by 14
Divide by 16
Divide by 18
Divide by 20
Divide by 22
Divide by 24
Divide by 26
Divide by 28
Divide by 30
Divide by 32
Divide by 34
Divide by 36
Divide by 38
Divide by 40
Divide by 42
Divide by 44
Divide by 46
Divide by 48
Divide by 50
Divide by 52
Divide by 54
Divide by 56
Divide by 58
Divide by 60
Divide by 62
Divide by 64
4 MHz
8 MHz
12 MHz
16 MHz
20 MHz
24 MHz
28 MHz
32 MHz
36 MHz
40 MHz
44 MHz
48 MHz
52 MHz
56 MHz
60 MHz
64 MHz
68 MHz
72 MHz
76 MHz
80 MHz
84 MHz
88 MHz
92 MHz
96 MHz
100 MHz
104 MHz
108 MHz
112 MHz
116 MHz
120 MHz
124 MHz
128 MHz
1 MHz
2 MHz
3 MHz
4 MHz
5 MHz
6 MHz
7 MHz
8 MHz
9 MHz
10 MHz
11 MHz
12 MHz
13 MHz
14 MHz
15 MHz
16 MHz
17 MHz
18 MHz
19 MHz
20 MHz
21 MHz
22 MHz
23 MHz
24 MHz
25 MHz
26 MHz
27 MHz
28 MHz
29 MHz
30 MHz
31 MHz
32 MHz
Chapter 7 Analog-to-Digital Converter (ATD10B16CV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 233
7.3.2.6 ATD Control Register 5 (ATDCTL5)
This register selects the type of conversion sequence and the analog input channels sampled. Writes to this
register will abort current conversion sequence and start a new conversion sequence.
Read: Anytime
Write: Anytime
76543210
RDJM DSGN SCAN MULT CD CC CB CA
W
Reset 0 0 0 00000
Figure 7-8. ATD Control Register 5 (ATDCTL5)
Table 7-14. ATDCTL5 Field Descriptions
Field Description
7
DJM Result Register Data Justification This bit controls justification of conversion data in the result registers.
See Section 7.3.2.16, “ATD Conversion Result Registers (ATDDRx)” for details.
0 Left justified data in the result registers.
1 Right justified data in the result registers.
6
DSGN Result Register Data Signed or Unsigned Representation This bit selects between signed and unsigned
conversion data representation in the result registers. Signed data is represented as 2’s complement. Signed
data is not available in right justification. See <st-bold>7.3.2.16 ATD Conversion Result Registers (ATDDRx)
for details.
0 Unsigned data representation in the result registers.
1 Signed data representation in the result registers.
Table 7-15 summarizes the result data formats available and how they are set up using the control bits.
Table 7-16 illustrates the difference between the signed and unsigned, left justified output codes for an input
signal range between 0 and 5.12 Volts.
5
SCAN Continuous Conversion Sequence Mode This bit selects whether conversion sequences are performed
continuously or only once.
0 Single conversion sequence
1 Continuous conversion sequences (scan mode)
4
MULT Multi-Channel Sample Mode — When MULT is 0, the ATD sequence controller samples only from the
specified analog input channel for an entire conversion sequence. The analog channel is selected by channel
selectioncode (controlbits CD/CC/CB/CAlocated in ATDCTL5).When MULT is1, theATD sequencecontroller
samplesacross channels. The number of channelssampledis determined bythe sequence length value(S8C,
S4C, S2C, S1C). The first analog channel examined is determined by channel selection code (CC, CB, CA
control bits); subsequent channels sampled in the sequence are determined by incrementing the channel
selection code or wrapping around to AN0 (channel 0.
0 Sample only one channel
1 Sample across several channels
Chapter 7 Analog-to-Digital Converter (ATD10B16CV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
234 Freescale Semiconductor
3:0
C[D:A} Analog Input Channel Select Code — These bits select the analog input channel(s) whose signals are
sampled and converted to digital codes. Table 7-17 lists the coding used to select the various analog input
channels.
In the case of single channel conversions (MULT = 0), this selection code specified the channel to be examined.
In the case of multiple channel conversions (MULT = 1), this selection code represents the first channel to be
examined in the conversion sequence. Subsequent channels are determined by incrementing the channel
selection code or wrapping around to AN0 (after converting the channel defined by the Wrap Around Channel
Select Bits WRAP[3:0] in ATDCTL0). In case starting with a channel number higher than the one defined by
WRAP[3:0] the first wrap around will be AN15 to AN0.
Table 7-15. Available Result Data Formats.
SRES8 DJM DSGN Result Data Formats
Description and Bus Bit Mapping
1
1
1
0
0
0
0
0
1
0
0
1
0
1
X
0
1
X
8-bit / left justified / unsigned — bits 15:8
8-bit / left justified / signed — bits 15:8
8-bit / right justified / unsigned — bits 7:0
10-bit / left justified / unsigned — bits 15:6
10-bit / left justified / signed -— bits 15:6
10-bit / right justified / unsigned — bits 9:0
Table 7-16. Left Justified, Signed and Unsigned ATD Output Codes.
Input Signal
VRL = 0 Volts
VRH = 5.12 Volts
Signed
8-Bit Codes Unsigned
8-Bit Codes Signed
10-Bit Codes Unsigned
10-Bit Codes
5.120 Volts
5.100
5.080
2.580
2.560
2.540
0.020
0.000
7F
7F
7E
01
00
FF
81
80
FF
FF
FE
81
80
7F
01
00
7FC0
7F00
7E00
0100
0000
FF00
8100
8000
FFC0
FF00
FE00
8100
8000
7F00
0100
0000
Table 7-14. ATDCTL5 Field Descriptions (continued)
Field Description
Chapter 7 Analog-to-Digital Converter (ATD10B16CV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 235
Table 7-17. Analog Input Channel Select Coding
CD CC CB CA Analog Input
Channel
0 0 0 0 AN0
0 0 0 1 AN1
0 0 1 0 AN2
0 0 1 1 AN3
0 1 0 0 AN4
0 1 0 1 AN5
0 1 1 0 AN6
0 1 1 1 AN7
1 0 0 0 AN8
1 0 0 1 AN9
1 0 1 0 AN10
1 0 1 1 AN11
1 1 0 0 AN12
1 1 0 1 AN13
1 1 1 0 AN14
1 1 1 1 AN15
Chapter 7 Analog-to-Digital Converter (ATD10B16CV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
236 Freescale Semiconductor
7.3.2.7 ATD Status Register 0 (ATDSTAT0)
This read-only register contains the Sequence Complete Flag, overrun flags for external trigger and FIFO
mode, and the conversion counter.
Read: Anytime
Write: Anytime (No effect on CC[3:0])
76543210
RSCF 0ETORF FIFOR CC3 CC2 CC1 CC0
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 7-9. ATD Status Register 0 (ATDSTAT0)
Table 7-18. ATDSTAT0 Field Descriptions
Field Description
7
SCF Sequence Complete Flag — This flag is set upon completion of a conversion sequence. If conversion
sequences are continuously performed (SCAN = 1), the flag is set after each one is completed. This flag is
cleared when one of the following occurs:
Write “1” to SCF
Write to ATDCTL5 (a new conversion sequence is started)
If AFFC = 1 and read of a result register
0 Conversion sequence not completed
1 Conversion sequence has completed
5
ETORF External Trigger Overrun Flag —While in edge trigger mode (ETRIGLE = 0), if additional active edges are
detected while a conversion sequence is in process the overrun flag is set. This flag is cleared when one of the
following occurs:
Write “1” to ETORF
Write to ATDCTL0,1,2,3,4 (a conversion sequence is aborted)
Write to ATDCTL5 (a new conversion sequence is started)
0 No External trigger over run error has occurred
1 External trigger over run error has occurred
Chapter 7 Analog-to-Digital Converter (ATD10B16CV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 237
4
FIFOR FIFO Over Run Flag — This bit indicates that a result register has been written to before its associated
conversion complete flag (CCF) has been cleared. This flag is most useful when usingtheFIFOmode because
the flag potentially indicates that result registers are out of sync with the input channels. However, it is also
practical for non-FIFO modes, and indicates that a result register has been over written before it has been read
(i.e., the old data has been lost). This flag is cleared when one of the following occurs:
Write “1” to FIFOR
Start a new conversion sequence (write to ATDCTL5 or external trigger)
0 No over run has occurred
1 Overrun condition exists (result register has been written while associated CCFx flag remained set)
3:0
CC[3:0} Conversion Counter These 4 read-only bits are the binary value of the conversion counter. The conversion
counter points to the result register that will receive the result of the current conversion. For example, CC3 = 0,
CC2 = 1, CC1 = 1, CC0 = 0 indicates that the result of the current conversion will be in ATD Result Register 6.
If in non-FIFO mode (FIFO = 0) the conversion counter is initialized to zero at the begin and end of the
conversion sequence. If in FIFO mode (FIFO = 1) the register counter is not initialized. The conversion
counters wraps around when its maximum value is reached.
Aborting a conversion or starting a new conversion by write to an ATDCTL register (ATDCTL5-0) clears the
conversion counter even if FIFO=1.
Table 7-18. ATDSTAT0 Field Descriptions (continued)
Field Description
Chapter 7 Analog-to-Digital Converter (ATD10B16CV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
238 Freescale Semiconductor
7.3.2.8 Reserved Register 0 (ATDTEST0)
Read: Anytime, returns unpredictable values
Write: Anytime in special modes, unimplemented in normal modes
NOTE
Writing to this register when in special modes can alter functionality.
7.3.2.9 ATD Test Register 1 (ATDTEST1)
This register contains the SC bit used to enable special channel conversions.
Read: Anytime, returns unpredictable values for bit 7 and bit 6
Write: Anytime
NOTE
Writing to this register when in special modes can alter functionality.
76543210
Ruuuuuuuu
W
Reset 1 0 0 00000
= Unimplemented or Reserved u = Unaffected
Figure 7-10. Reserved Register 0 (ATDTEST0)
76543210
Ruuuuuuu
SC
W
Reset 0 0 0 00000
= Unimplemented or Reserved u = Unaffected
Figure 7-11. Reserved Register 1 (ATDTEST1)
Table 7-19. ATDTEST1 Field Descriptions
Field Description
0
SC Special Channel Conversion Bit — If this bit is set, then special channel conversion can be selected using
CC, CB, and CA of ATDCTL5. Table 7-20 lists the coding.
0 Special channel conversions disabled
1 Special channel conversions enabled
Chapter 7 Analog-to-Digital Converter (ATD10B16CV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 239
7.3.2.10 ATD Status Register 2 (ATDSTAT2)
This read-only register contains the Conversion Complete Flags CCF15 to CCF8.
Read: Anytime
Write: Anytime, no effect
Table 7-20. Special Channel Select Coding
SC CD CC CB CA Analog Input Channel
1 0 0 X X Reserved
101 0 0 V
RH
101 0 1 V
RL
101 1 0 (V
RH+VRL) / 2
1 0 1 1 1 Reserved
1 1 X X X Reserved
76543210
R CCF15 CCF14 CCF13 CCF12 CCF11 CCF10 CCF9 CCF8
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 7-12. ATD Status Register 2 (ATDSTAT2)
Table 7-21. ATDSTAT2 Field Descriptions
Field Description
7:0
CCF[15:8] Conversion Complete Flag Bits — A conversion complete flag is set at the end of each conversion in a
conversion sequence. The flags are associated with the conversion position in a sequence (and also the result
register number). Therefore, CCF8 is set when the ninth conversion in a sequence is complete and the result
is available in result register ATDDR8; CCF9 is set when the tenth conversion in a sequence is complete and
the result is available in ATDDR9, and so forth. A flag CCFx (x = 15, 14, 13, 12, 11, 10, 9, 8) is cleared when
one of the following occurs:
Write to ATDCTL5 (a new conversion sequence is started)
If AFFC = 0 and read of ATDSTAT2 followed by read of result register ATDDRx
If AFFC = 1 and read of result register ATDDRx
In case of a concurrent set and clear on CCFx: The clearing by method A) will overwrite the set. The clearing
by methods B) or C) will be overwritten by the set.
0 Conversion number x not completed
1 Conversion number x has completed, result ready in ATDDRx
Chapter 7 Analog-to-Digital Converter (ATD10B16CV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
240 Freescale Semiconductor
7.3.2.11 ATD Status Register 1 (ATDSTAT1)
This read-only register contains the Conversion Complete Flags CCF7 to CCF0
Read: Anytime
Write: Anytime, no effect
76543210
R CCF7 CCF6 CCF5 CCF4 CCF3 CCF2 CCF1 CCF0
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 7-13. ATD Status Register 1 (ATDSTAT1)
Table 7-22. ATDSTAT1 Field Descriptions
Field Description
7:0
CCF[7:0] Conversion Complete Flag Bits — A conversion complete flag is set at the end of each conversion in a
conversion sequence. The flags are associated with the conversion position in a sequence (and also the result
register number). Therefore, CCF0 is set when the first conversion in a sequence is complete and the result is
available in result register ATDDR0; CCF1 is set when the second conversion in a sequence is complete and
the result is available in ATDDR1, and so forth. A CCF flag is cleared when one of the following occurs:
Write to ATDCTL5 (a new conversion sequence is started)
If AFFC = 0 and read of ATDSTAT1 followed by read of result register ATDDRx
If AFFC = 1 and read of result register ATDDRx
In case of a concurrent set and clear on CCFx: The clearing by method A) will overwrite the set. The clearing
by methods B) or C) will be overwritten by the set.
Conversion number x not completed
Conversion number x has completed, result ready in ATDDRx
Chapter 7 Analog-to-Digital Converter (ATD10B16CV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 241
7.3.2.12 ATD Input Enable Register 0 (ATDDIEN0)
Read: Anytime
Write: anytime
7.3.2.13 ATD Input Enable Register 1 (ATDDIEN1)
Read: Anytime
Write: Anytime
76543210
RIEN15 IEN14 IEN13 IEN12 IEN11 IEN10 IEN9 IEN8
W
Reset 0 0 0 00000
Figure 7-14. ATD Input Enable Register 0 (ATDDIEN0)
Table 7-23. ATDDIEN0 Field Descriptions
Field Description
7:0
IEN[15:8] ATD Digital Input Enable on Channel Bits — This bit controls the digital input buffer from the analog input
pin (ANx) to PTADx data register.
0 Disable digital input buffer to PTADx
1 Enable digital input buffer to PTADx.
Note: Setting this bit will enable the corresponding digital input buffer continuously. If this bit is set while
simultaneously using it as an analog port, there is potentially increased power consumption because the
digital input buffer maybe in the linear region.
76543210
RIEN7 IEN6 IEN5 IEN4 IEN3 IEN2 IEN1 IEN0
W
Reset 0 0 0 00000
Figure 7-15. ATD Input Enable Register 1 (ATDDIEN1)
Table 7-24. ATDDIEN1 Field Descriptions
Field Description
7:0
IEN[7:0] ATD Digital Input Enable on Channel Bits — This bit controls the digital input buffer from the analog input
pin (ANx) to PTADx data register.
0 Disable digital input buffer to PTADx
1 Enable digital input buffer to PTADx.
Note: Setting this bit will enable the corresponding digital input buffer continuously. If this bit is set while
simultaneously using it as an analog port, there is potentially increased power consumption because the
digital input buffer maybe in the linear region.
Chapter 7 Analog-to-Digital Converter (ATD10B16CV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
242 Freescale Semiconductor
7.3.2.14 Port Data Register 0 (PORTAD0)
The data port associated with the ATD is input-only. The port pins are shared with the analog A/D inputs
AN[15:8].
Read: Anytime
Write: Anytime, no effect
The A/D input channels may be used for general-purpose digital input.
76543210
R PTAD15 PTAD14 PTAD13 PTAD12 PTAD11 PTAD10 PTAD9 PTAD8
W
Reset 1 1 1 11111
Pin
Function AN15 AN14 AN13 AN12 AN11 AN10 AN9 AN8
= Unimplemented or Reserved
Figure 7-16. Port Data Register 0 (PORTAD0)
Table 7-25. PORTAD0 Field Descriptions
Field Description
7:0
PTAD[15:8] A/D Channel x (ANx) Digital Input Bits— If the digital input buffer on the ANx pin is enabled (IENx = 1) or
channel x is enabled as external trigger (ETRIGE = 1, ETRIGCH[3-0] = x, ETRIGSEL = 0) read returns the
logic level on ANx pin (signal potentials not meeting VIL or VIH specifications will have an indeterminate value)).
If the digital input buffers are disabled (IENx = 0) and channel x is not enabled as external trigger, read returns
a “1”.
Reset sets all PORTAD0 bits to “1”.
Chapter 7 Analog-to-Digital Converter (ATD10B16CV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 243
7.3.2.15 Port Data Register 1 (PORTAD1)
The data port associated with the ATD is input-only. The port pins are shared with the analog A/D inputs
AN7-0.
Read: Anytime
Write: Anytime, no effect
The A/D input channels may be used for general-purpose digital input.
76543210
R PTAD7 PTAD6 PTAD5 PTAD4 PTAD3 PTAD2 PTAD1 PTAD0
W
Reset 1 1 1 11111
Pin
Function AN 7 AN6 AN5 AN4 AN3 AN2 AN1 AN0
= Unimplemented or Reserved
Figure 7-17. Port Data Register 1 (PORTAD1)
Table 7-26. PORTAD1 Field Descriptions
Field Description
7:0
PTAD[7:8] A/D Channel x (ANx) Digital Input Bits — If the digital input buffer on the ANx pin is enabled (IENx=1) or
channel x is enabled as external trigger (ETRIGE = 1, ETRIGCH[3-0] = x, ETRIGSEL = 0) read returns the
logic level on ANx pin (signal potentials not meeting VIL or VIH specifications will have an indeterminate value)).
If the digital input buffers are disabled (IENx = 0) and channel x is not enabled as external trigger, read returns
a “1”.
Reset sets all PORTAD1 bits to “1”.
Chapter 7 Analog-to-Digital Converter (ATD10B16CV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
244 Freescale Semiconductor
7.3.2.16 ATD Conversion Result Registers (ATDDRx)
The A/D conversion results are stored in 16 read-only result registers. The result data is formatted in the
result registers bases on two criteria. First there is left and right justification; this selection is made using
the DJM control bit in ATDCTL5. Second there is signed and unsigned data; this selection is made using
the DSGN control bit in ATDCTL5. Signed data is stored in 2’s complement format and only exists in left
justified format. Signed data selected for right justified format is ignored.
Read: Anytime
Write: Anytime in special mode, unimplemented in normal modes
7.3.2.16.1 Left Justified Result Data
76543210
R (10-BIT)
R (8-BIT) BIT 9 MSB
BIT 7 MSB BIT 8
BIT 6 BIT 7
BIT 5 BIT 6
BIT 4 BIT 5
BIT 3 BIT 4
BIT 2 BIT 3
BIT 1 BIT 2
BIT 0
W
Reset 00000000
= Unimplemented or Reserved
Figure 7-18. Left Justified, ATD Conversion Result Register x, High Byte (ATDDRxH)
76543210
R (10-BIT)
R (8-BIT) BIT 1
uBIT 0
u0
00
00
00
00
00
0
W
Reset 00000000
= Unimplemented or Reserved u = Unaffected
Figure 7-19. Left Justified, ATD Conversion Result Register x, Low Byte (ATDDRxL)
Chapter 7 Analog-to-Digital Converter (ATD10B16CV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 245
7.3.2.16.2 Right Justified Result Data
7.4 Functional Description
The ATD10B16C is structured in an analog and a digital sub-block.
7.4.1 Analog Sub-block
The analog sub-block contains all analog electronics required to perform a single conversion. Separate
power supplies VDDA and VSSA allow to isolate noise of other MCU circuitry from the analog sub-block.
7.4.1.1 Sample and Hold Machine
The sample and hold (S/H) machine accepts analog signals from the external world and stores them as
capacitor charge on a storage node.
The sample process uses a two stage approach. During the first stage, the sample amplifier is used to
quickly charge the storage node.The second stage connects the input directly to the storage node to
complete the sample for high accuracy.
When not sampling, the sample and hold machine disables its own clocks. The analog electronics continue
drawing their quiescent current. The power down (ADPU) bit must be set to disable both the digital clocks
and the analog power consumption.
The input analog signals are unipolar and must fall within the potential range of VSSA to VDDA.
76543210
R (10-BIT)
R (8-BIT) 0
00
00
00
00
00
0BIT 9 MSB
0BIT 8
0
W
Reset 00000000
= Unimplemented or Reserved
Figure 7-20. Right Justified, ATD Conversion Result Register x, High Byte (ATDDRxH)
76543210
R (10-BIT)
R (8-BIT) BIT 7
BIT 7 MSB BIT 6
BIT 6 BIT 5
BIT 5 BIT 4
BIT 4 BIT 3
BIT 3 BIT 2
BIT 2 BIT 1
BIT 1 BIT 0
BIT 0
W
Reset 00000000
= Unimplemented or Reserved
Figure 7-21. Right Justified, ATD Conversion Result Register x, Low Byte (ATDDRxL)
Chapter 7 Analog-to-Digital Converter (ATD10B16CV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
246 Freescale Semiconductor
7.4.1.2 Analog Input Multiplexer
The analog input multiplexer connects one of the 16 external analog input channels to the sample and hold
machine.
7.4.1.3 Sample Buffer Amplifier
The sample amplifier is used to buffer the input analog signal so that the storage node can be quickly
charged to the sample potential.
7.4.1.4 Analog-to-Digital (A/D) Machine
The A/D machine performs analog to digital conversions. The resolution is program selectable at either 8
or 10 bits. The A/D machine uses a successive approximation architecture. It functions by comparing the
stored analog sample potential with a series of digitally generated analog potentials. By following a binary
search algorithm, the A/D machine locates the approximating potential that is nearest to the sampled
potential.
When not converting the A/D machine disables its own clocks. The analog electronics continue drawing
quiescent current. The power down (ADPU) bit must be set to disable both the digital clocks and the analog
power consumption.
Only analog input signals within the potential range of VRL to VRH (A/D reference potentials) will result
in a non-railed digital output codes.
7.4.2 Digital Sub-Block
This subsection explains some of the digital features in more detail. See register descriptions for all details.
7.4.2.1 External Trigger Input
The external trigger feature allows the user to synchronize ATD conversions to the external environment
events rather than relying on software to signal the ATD module when ATD conversions are to take place.
The external trigger signal (out of reset ATD channel 15, configurable in ATDCTL1) is programmable to
be edge or level sensitive with polarity control. Table 7-27 gives a brief description of the different
combinations of control bits and their effect on the external trigger function.
During a conversion, if additional active edges are detected the overrun error flag ETORF is set.
Table 7-27. External Trigger Control Bits
ETRIGLE ETRIGP ETRIGE SCAN Description
X X 0 0 Ignores external trigger. Performs one conversion sequence and stops.
X X 0 1 Ignores external trigger. Performs continuous conversion sequences.
0 0 1 X Falling edge triggered. Performs one conversion sequence per trigger.
0 1 1 X Rising edge triggered. Performs one conversion sequence per trigger.
1 0 1 X Trigger active low. Performs continuous conversions while trigger is active.
1 1 1 X Trigger active high. Performs continuous conversions while trigger is active.
Chapter 7 Analog-to-Digital Converter (ATD10B16CV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 247
In either level or edge triggered modes, the first conversion begins when the trigger is received. In both
cases, the maximum latency time is one bus clock cycle plus any skew or delay introduced by the trigger
circuitry.
After ETRIGE is enabled, conversions cannot be started by a write to ATDCTL5, but rather must be
triggered externally.
If the level mode is active and the external trigger both de-asserts and re-asserts itself during a conversion
sequence, this does not constitute an overrun. Therefore, the flag is not set. If the trigger remains asserted
in level mode while a sequence is completing, another sequence will be triggered immediately.
7.4.2.2 General-Purpose Digital Input Port Operation
The input channel pins can be multiplexed between analog and digital data. As analog inputs, they are
multiplexed and sampled to supply signals to the A/D converter. As digital inputs, they supply external
input data that can be accessed through the digital port registers (PORTAD0 & PORTAD1) (input-only).
The analog/digital multiplex operation is performed in the input pads. The input pad is always connected
to the analog inputs of the ATD10B16C. The input pad signal is buffered to the digital port registers. This
buffer can be turned on or off with the ATDDIEN0 & ATDDIEN1 register. This is important so that the
buffer does not draw excess current when analog potentials are presented at its input.
7.4.3 Operation in Low Power Modes
The ATD10B16C can be configured for lower MCU power consumption in three different ways:
Stop Mode
Stop Mode: This halts A/D conversion. Exit from Stop mode will resume A/D conversion, But due
to the recovery time the result of this conversion should be ignored.
Entering stop mode causes all clocks to halt and thus the system is placed in a minimum power
standby mode. This halts any conversion sequence in progress. During recovery from stop mode,
there must be a minimum delay for the stop recovery time tSR before initiating a new ATD
conversion sequence.
Wait Mode
Wait Mode with AWAI = 1: This halts A/D conversion. Exit from Wait mode will resume A/D
conversion, but due to the recovery time the result of this conversion should be ignored.
Entering wait mode, the ATD conversion either continues or halts for low power depending on the
logical value of the AWAIT bit.
Freeze Mode
Writing ADPU = 0 (Note that all ATD registers remain accessible.): This aborts any A/D
conversion in progress.
In freeze mode, the ATD10B16C will behave according to the logical values of the FRZ1 and FRZ0
bits. This is useful for debugging and emulation.
NOTE
The reset value for the ADPU bit is zero. Therefore, when this module is
reset, it is reset into the power down state.
Chapter 7 Analog-to-Digital Converter (ATD10B16CV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
248 Freescale Semiconductor
7.5 Resets
At reset the ATD10B16C is in a power down state. The reset state of each individual bit is listed within
Section 7.3, “Memory Map and Register Definition, which details the registers and their bit fields.
7.6 Interrupts
The interrupt requested by the ATD10B16C is listed in Table 7-28. Refer to MCU specification for related
vector address and priority.
See Section 7.3.2, “Register Descriptions, for further details.
Table 7-28. ATD Interrupt Vectors
Interrupt Source CCR Mask Local Enable
Sequence Complete Interrupt I bit ASCIE in ATDCTL2
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 249
Chapter 8
Inter-Integrated Circuit (IICV2) Block Description
8.1 Introduction
The inter-IC bus (IIC) is a two-wire, bidirectional serial bus that provides a simple, efficient method of data
exchange between devices. Being a two-wire device, the IIC bus minimizes the need for large numbers of
connections between devices, and eliminates the need for an address decoder.
This bus is suitable for applications requiring occasional communications over a short distance between a
number of devices. It also provides flexibility, allowing additional devices to be connected to the bus for
further expansion and system development.
The interface is designed to operate up to 100 kbps with maximum bus loading and timing. The device is
capable of operating at higher baud rates, up to a maximum of clock/20, with reduced bus loading. The
maximum communication length and the number of devices that can be connected are limited by a
maximum bus capacitance of 400 pF.
8.1.1 Features
The IIC module has the following key features:
Compatible with I2C bus standard
Multi-master operation
Software programmable for one of 256 different serial clock frequencies
Software selectable acknowledge bit
Interrupt driven byte-by-byte data transfer
Arbitration lost interrupt with automatic mode switching from master to slave
Version
Number Revision
Date Effective
Date Author Description of Changes
0.1 8-Sep-99 Original draft. Distributed only within Freescale
2.06 18-Aug-20
02
Reformated for SRS3.0,and add examples for programing general
use and some diagrams to make it more user friendly as suggested
by Joachim
2.07 12-Mar-20
04 Changed to Freescale chapter format
Chapter 8 Inter-Integrated Circuit (IICV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
250 Freescale Semiconductor
Calling address identification interrupt
Start and stop signal generation/detection
Repeated start signal generation
Acknowledge bit generation/detection
Bus busy detection
Chapter 8 Inter-Integrated Circuit (IICV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 251
8.1.2 Modes of Operation
The IIC functions the same in normal, special, and emulation modes. It has two low power modes: wait
and stop modes.
8.1.3 Block Diagram
The block diagram of the IIC module is shown in Figure 8-1.
Figure 8-1. IIC Block Diagram
In/Out
Data
Shift
Register
Address
Compare
SDA
Interrupt
Clock
Control
Start
Stop
Arbitration
Control
SCL
bus_clock
IIC
Registers
Chapter 8 Inter-Integrated Circuit (IICV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
252 Freescale Semiconductor
8.2 External Signal Description
The IICV2 module has two external pins.
8.2.1 IIC_SCL — Serial Clock Line Pin
This is the bidirectional serial clock line (SCL) of the module, compatible to the IIC bus specification.
8.2.2 IIC_SDA — Serial Data Line Pin
This is the bidirectional serial data line (SDA) of the module, compatible to the IIC bus specification.
8.3 Memory Map and Register Definition
This section provides a detailed description of all memory and registers for the IIC module.
8.3.1 Module Memory Map
The memory map for the IIC module is given below in Figure 8-2. The address listed for each register is
the address offset.The total address for each register is the sum of the base address for the IIC module and
the address offset for each register.
Chapter 8 Inter-Integrated Circuit (IICV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 253
8.3.2 Register Descriptions
This section consists of register descriptions in address order. Each description includes a standard register
diagram with an associated figure number. Details of register bit and field function follow the register
diagrams, in bit order.
8.3.2.1 IIC Address Register (IBAD)
Read and write anytime
This register contains the address the IIC bus will respond to when addressed as a slave; note that it is not
the address sent on the bus during the address transfer.
Register
Name Bit 7 654321Bit 0
0x0000
IBAD RADR7 ADR6 ADR5 ADR4 ADR3 ADR2 ADR1 0
W
0x0001
IBFD RIBC7 IBC6 IBC5 IBC4 IBC3 IBC2 IBC1 IBC0
W
0x0002
IBCR RIBEN IBIE MS/SL Tx/Rx TXAK 00
IBSWAI
WRSTA
0x0003
IBSR R TCF IAAS IBB IBAL 0SRW
IBIF RXAK
W
0x0004
IBDR RD7 D6 D5 D4 D3 D2 D1 D0
W
= Unimplemented or Reserved
Figure 8-2. IIC Register Summary
Offset Module Base +0x0000
76543210
RADR7 ADR6 ADR5 ADR4 ADR3 ADR2 ADR1 0
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 8-3. IIC Bus Address Register (IBAD)
Chapter 8 Inter-Integrated Circuit (IICV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
254 Freescale Semiconductor
8.3.2.2 IIC Frequency Divider Register (IBFD)
Read and write anytime
Table 8-1. IBAD Field Descriptions
Field Description
7:1
ADR[7:1] Slave Address Bit 1 to bit 7 contain the specific slave address to be used by the IIC bus module.The default
mode of IIC bus is slave mode for an address match on the bus.
0
Reserved Reserved — Bit 0 of the IBAD is reserved for future compatibility. This bit will always read 0.
Offset Module Base + 0x0001
76543210
RIBC7 IBC6 IBC5 IBC4 IBC3 IBC2 IBC1 IBC0
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 8-4. IIC Bus Frequency Divider Register (IBFD)
Table 8-2. IBFD Field Descriptions
Field Description
7:0
IBC[7:0] I Bus Clock Rate 7:0 — This field is used to prescale the clock for bit rate selection. The bit clock generator is
implemented as a prescale divider IBC7:6, prescaled shift register IBC5:3 select the prescaler divider and
IBC2-0 select the shift register tap point. The IBC bits are decoded to give the tap and prescale values as shown
in Table 8-3.
Table 8-3. I-Bus Tap and Prescale Values
IBC2-0
(bin) SCL Tap
(clocks) SDA Tap
(clocks)
000 5 1
001 6 1
010 7 2
011 8 2
100 9 3
101 10 3
110 12 4
111 15 4
IBC5-3
(bin) scl2start
(clocks) scl2stop
(clocks) scl2tap
(clocks) tap2tap
(clocks)
0002741
0012742
Chapter 8 Inter-Integrated Circuit (IICV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 255
The number of clocks from the falling edge of SCL to the first tap (Tap[1]) is defined by the values shown
in the scl2tap column of Table 8-3, all subsequent tap points are separated by 2IBC5-3 as shown in the
tap2tap column in Table 8-3. The SCL Tap is used to generated the SCL period and the SDA Tap is used
to determine the delay from the falling edge of SCL to SDA changing, the SDA hold time.
IBC7–6 defines the multiplier factor MUL. The values of MUL are shown in the Table 8-4.
0102964
0116968
100 14 17 14 16
101 30 33 30 32
110 62 65 62 64
111 126 129 126 128
Table 8-4. Multiplier Factor
IBC7-6 MUL
00 01
01 02
10 04
11 RESERVED
IBC5-3
(bin) scl2start
(clocks) scl2stop
(clocks) scl2tap
(clocks) tap2tap
(clocks)
SCL Divider
SDA Hold
SCL
SDA
Chapter 8 Inter-Integrated Circuit (IICV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
256 Freescale Semiconductor
Figure 8-5. SCL Divider and SDA Hold
The equation used to generate the divider values from the IBFD bits is:
SCL Divider = MUL x {2 x (scl2tap + [(SCL_Tap -1) x tap2tap] + 2)}
The SDA hold delay is equal to the CPU clock period multiplied by the SDA Hold value shown in
Table 8-5. The equation used to generate the SDA Hold value from the IBFD bits is:
SDA Hold = MUL x {scl2tap + [(SDA_Tap - 1) x tap2tap] + 3}
The equation for SCL Hold values to generate the start and stop conditions from the IBFD bits is:
SCL Hold(start) = MUL x [scl2start + (SCL_Tap - 1) x tap2tap]
SCL Hold(stop) = MUL x [scl2stop + (SCL_Tap - 1) x tap2tap]
Table 8-5. IIC Divider and Hold Values (Sheet 1 of 5)
IBC[7:0]
(hex) SCL Divider
(clocks) SDA Hold
(clocks) SCL Hold
(start) SCL Hold
(stop)
MUL=1 00 20 7 6 11
01 22 7 7 12
02 24 8 8 13
03 26 8 9 14
04 28 9 10 15
05 30 9 11 16
06 34 10 13 18
07 40 10 16 21
08 28 7 10 15
09 32 7 12 17
0A 36 9 14 19
0B 40 9 16 21
0C 44 11 18 23
0D 48 11 20 25
0E 56 13 24 29
0F 68 13 30 35
10 48 9 18 25
SDA
SCL
START condition STOP condition
SCL Hold(start) SCL Hold(stop)
Chapter 8 Inter-Integrated Circuit (IICV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 257
11 56 9 22 29
12 64 13 26 33
13 72 13 30 37
14 80 17 34 41
15 88 17 38 45
16 104 21 46 53
17 128 21 58 65
18 80 9 38 41
19 96 9 46 49
1A 112 17 54 57
1B 128 17 62 65
1C 144 25 70 73
1D 160 25 78 81
1E 192 33 94 97
1F 240 33 118 121
20 160 17 78 81
21 192 17 94 97
22 224 33 110 113
23 256 33 126 129
24 288 49 142 145
25 320 49 158 161
26 384 65 190 193
27 480 65 238 241
28 320 33 158 161
29 384 33 190 193
2A 448 65 222 225
2B 512 65 254 257
2C 576 97 286 289
2D 640 97 318 321
2E 768 129 382 385
2F 960 129 478 481
30 640 65 318 321
31 768 65 382 385
32 896 129 446 449
33 1024 129 510 513
34 1152 193 574 577
35 1280 193 638 641
36 1536 257 766 769
37 1920 257 958 961
38 1280 129 638 641
39 1536 129 766 769
3A 1792 257 894 897
3B 2048 257 1022 1025
3C 2304 385 1150 1153
3D 2560 385 1278 1281
Table 8-5. IIC Divider and Hold Values (Sheet 2 of 5)
IBC[7:0]
(hex) SCL Divider
(clocks) SDA Hold
(clocks) SCL Hold
(start) SCL Hold
(stop)
Chapter 8 Inter-Integrated Circuit (IICV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
258 Freescale Semiconductor
3E 3072 513 1534 1537
3F 3840 513 1918 1921
MUL=2 40 40 14 12 22
41 44 14 14 24
42 48 16 16 26
43 52 16 18 28
44 56 18 20 30
45 60 18 22 32
46 68 20 26 36
47 80 20 32 42
48 56 14 20 30
49 64 14 24 34
4A 72 18 28 38
4B 80 18 32 42
4C 88 22 36 46
4D 96 22 40 50
4E 112 26 48 58
4F 136 26 60 70
50 96 18 36 50
51 112 18 44 58
52 128 26 52 66
53 144 26 60 74
54 160 34 68 82
55 176 34 76 90
56 208 42 92 106
57 256 42 116 130
58 160 18 76 82
59 192 18 92 98
5A 224 34 108 114
5B 256 34 124 130
5C 288 50 140 146
5D 320 50 156 162
5E 384 66 188 194
5F 480 66 236 242
60 320 34 156 162
61 384 34 188 194
62 448 66 220 226
63 512 66 252 258
64 576 98 284 290
65 640 98 316 322
66 768 130 380 386
67 960 130 476 482
68 640 66 316 322
69 768 66 380 386
Table 8-5. IIC Divider and Hold Values (Sheet 3 of 5)
IBC[7:0]
(hex) SCL Divider
(clocks) SDA Hold
(clocks) SCL Hold
(start) SCL Hold
(stop)
Chapter 8 Inter-Integrated Circuit (IICV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 259
6A 896 130 444 450
6B 1024 130 508 514
6C 1152 194 572 578
6D 1280 194 636 642
6E 1536 258 764 770
6F 1920 258 956 962
70 1280 130 636 642
71 1536 130 764 770
72 1792 258 892 898
73 2048 258 1020 1026
74 2304 386 1148 1154
75 2560 386 1276 1282
76 3072 514 1532 1538
77 3840 514 1916 1922
78 2560 258 1276 1282
79 3072 258 1532 1538
7A 3584 514 1788 1794
7B 4096 514 2044 2050
7C 4608 770 2300 2306
7D 5120 770 2556 2562
7E 6144 1026 3068 3074
7F 7680 1026 3836 3842
MUL=4 80 80 28 24 44
81 88 28 28 48
82 96 32 32 52
83 104 32 36 56
84 112 36 40 60
85 120 36 44 64
86 136 40 52 72
87 160 40 64 84
88 112 28 40 60
89 128 28 48 68
8A 144 36 56 76
8B 160 36 64 84
8C 176 44 72 92
8D 192 44 80 100
8E 224 52 96 116
8F 272 52 120 140
90 192 36 72 100
91 224 36 88 116
92 256 52 104 132
93 288 52 120 148
94 320 68 136 164
95 352 68 152 180
Table 8-5. IIC Divider and Hold Values (Sheet 4 of 5)
IBC[7:0]
(hex) SCL Divider
(clocks) SDA Hold
(clocks) SCL Hold
(start) SCL Hold
(stop)
Chapter 8 Inter-Integrated Circuit (IICV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
260 Freescale Semiconductor
96 416 84 184 212
97 512 84 232 260
98 320 36 152 164
99 384 36 184 196
9A 448 68 216 228
9B 512 68 248 260
9C 576 100 280 292
9D 640 100 312 324
9E 768 132 376 388
9F 960 132 472 484
A0 640 68 312 324
A1 768 68 376 388
A2 896 132 440 452
A3 1024 132 504 516
A4 1152 196 568 580
A5 1280 196 632 644
A6 1536 260 760 772
A7 1920 260 952 964
A8 1280 132 632 644
A9 1536 132 760 772
AA 1792 260 888 900
AB 2048 260 1016 1028
AC 2304 388 1144 1156
AD 2560 388 1272 1284
AE 3072 516 1528 1540
AF 3840 516 1912 1924
B0 2560 260 1272 1284
B1 3072 260 1528 1540
B2 3584 516 1784 1796
B3 4096 516 2040 2052
B4 4608 772 2296 2308
B5 5120 772 2552 2564
B6 6144 1028 3064 3076
B7 7680 1028 3832 3844
B8 5120 516 2552 2564
B9 6144 516 3064 3076
BA 7168 1028 3576 3588
BB 8192 1028 4088 4100
BC 9216 1540 4600 4612
BD 10240 1540 5112 5124
BE 12288 2052 6136 6148
BF 15360 2052 7672 7684
Table 8-5. IIC Divider and Hold Values (Sheet 5 of 5)
IBC[7:0]
(hex) SCL Divider
(clocks) SDA Hold
(clocks) SCL Hold
(start) SCL Hold
(stop)
Chapter 8 Inter-Integrated Circuit (IICV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 261
8.3.2.3 IIC Control Register (IBCR)
Read and write anytime
Offset Module Base + 0x0002
76543210
RIBEN IBIE MS/SL Tx/Rx TXAK 00
IBSWAI
WRSTA
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 8-6. IIC Bus Control Register (IBCR)
Table 8-6. IBCR Field Descriptions
Field Description
7
IBEN I-Bus Enable — This bit controls the software reset of the entire IIC bus module.
0 The module is reset and disabled. This is the power-on reset situation. When low the interface is held in reset
but registers can be accessed
1 The IIC bus module is enabled.This bit must be set before any other IBCR bits have any effect
If the IIC bus module is enabled in the middle of a byte transfer the interface behaves as follows: slave mode
ignores the current transfer on the bus and starts operating whenever a subsequent start condition is detected.
Master mode will not be aware that the bus is busy, hence if a start cycle is initiated then the current bus cycle
may become corrupt. This would ultimately result in either the current bus master or the IIC bus module losing
arbitration, after which bus operation would return to normal.
6
IBIE I-Bus Interrupt Enable
0 Interrupts from the IIC bus module are disabled. Note that this does not clear any currently pending interrupt
condition
1 Interrupts from the IIC bus module are enabled. An IIC bus interrupt occurs provided the IBIF bit in the status
register is also set.
5
MS/SL Master/Slave Mode Select Bit Upon reset, this bit is cleared. When this bit is changed from 0 to 1, a START
signal is generated on the bus, and the master mode is selected. When this bit is changed from 1 to 0, a STOP
signal is generated and the operation mode changes from master to slave.A STOP signal should only be
generated if the IBIF flag is set. MS/SL is cleared without generating a STOP signal when the master loses
arbitration.
0 Slave Mode
1 Master Mode
4
Tx/Rx Transmit/Receive Mode Select Bit — This bit selects the direction of master and slave transfers. When
addressed as a slave this bit should be set by software according to the SRW bit in the status register. In master
mode this bit should be set according to the type of transfer required. Therefore, for address cycles, this bit will
always be high.
0 Receive
1 Transmit
3
TXAK Transmit Acknowledge Enable This bit specifies the value driven onto SDA during data acknowledge cycles
for both master and slave receivers. The IIC module will always acknowledge address matches, provided it is
enabled, regardless of the value of TXAK. Note that values written to this bit are only used when the IIC bus is a
receiver, not a transmitter.
0 An acknowledge signal will be sent out to the bus at the 9th clock bit after receiving one byte data
1 No acknowledge signal response is sent (i.e., acknowledge bit = 1)
Chapter 8 Inter-Integrated Circuit (IICV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
262 Freescale Semiconductor
Wait mode is entered via execution of a CPU WAI instruction. In the event that the IBSWAI bit is set, all
clocks internal to the IIC will be stopped and any transmission currently in progress will halt.If the CPU
were woken up by a source other than the IIC module, then clocks would restart and the IIC would resume
from where was during the previous transmission. It is not possible for the IIC to wake up the CPU when
its internal clocks are stopped.
If it were the case that the IBSWAI bit was cleared when the WAI instruction was executed, the IIC internal
clocks and interface would remain alive, continuing the operation which was currently underway. It is also
possible to configure the IIC such that it will wake up the CPU via an interrupt at the conclusion of the
current operation. See the discussion on the IBIF and IBIE bits in the IBSR and IBCR, respectively.
8.3.2.4 IIC Status Register (IBSR)
This status register is read-only with exception of bit 1 (IBIF) and bit 4 (IBAL), which are software
clearable.
2
RSTA Repeat Start — Writing a 1 to this bit will generate a repeated START condition on the bus, provided it is the
current bus master. This bit will always be read as a low. Attempting a repeated start at the wrong time, if the bus
is owned by another master, will result in loss of arbitration.
1 Generate repeat start cycle
1
RESERVED Reserved — Bit 1 of the IBCR is reserved for future compatibility. This bit will always read 0.
0
IBSWAI I Bus Interface Stop in Wait Mode
0 IIC bus module clock operates normally
1 Halt IIC bus module clock generation in wait mode
Offset Module Base + 0x0003
76543210
R TCF IAAS IBB IBAL 0SRW
IBIF RXAK
W
Reset 1 0 0 00000
= Unimplemented or Reserved
Figure 8-7. IIC Bus Status Register (IBSR)
Table 8-7. IBSR Field Descriptions
Field Description
7
TCF Data Transferring Bit — While one byte of data is being transferred, this bit is cleared. It is set by the falling
edge of the 9th clock of a byte transfer. Note that this bit is only valid during or immediately following a transfer
to the IIC module or from the IIC module.
0 Transfer in progress
1 Transfer complete
Table 8-6. IBCR Field Descriptions (continued)
Field Description
Chapter 8 Inter-Integrated Circuit (IICV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 263
6
IAAS Addressed as a Slave Bit When its own specific address (I-bus address register) is matched with the calling
address, this bit is set.The CPU is interrupted provided the IBIE is set.Then the CPU needs to check the SRW
bit and set its Tx/Rx mode accordingly.Writing to the I-bus control register clears this bit.
0 Not addressed
1 Addressed as a slave
5
IBB Bus Busy Bit
0 This bit indicates the status of the bus. When a START signal is detected, the IBB is set. If a STOP signal is
detected, IBB is cleared and the bus enters idle state.
1 Bus is busy
4
IBAL Arbitration Lost — The arbitration lost bit (IBAL) is set by hardware when the arbitration procedure is lost.
Arbitration is lost in the following circumstances:
1. SDA sampled low when the master drives a high during an address or data transmit cycle.
2. SDA sampled low when the master drives a high during the acknowledge bit of a data receive cycle.
3. A start cycle is attempted when the bus is busy.
4. A repeated start cycle is requested in slave mode.
5. A stop condition is detected when the master did not request it.
This bit must be cleared by software, by writing a one to it. A write of 0 has no effect on this bit.
3
RESERVED Reserved — Bit 3 of IBSR is reserved for future use. A read operation on this bit will return 0.
2
SRW Slave Read/Write When IAAS is set this bit indicates the value of the R/W command bit of the calling address
sent from the master
This bit is only valid when the I-bus is in slave mode, a complete address transfer has occurred with an address
match and no other transfers have been initiated.
Checking this bit, the CPU can select slave transmit/receive mode according to the command of the master.
0 Slave receive, master writing to slave
1 Slave transmit, master reading from slave
1
IBIF I-Bus Interrupt — The IBIF bit is set when one of the following conditions occurs:
— Arbitration lost (IBAL bit set)
— Byte transfer complete (TCF bit set)
— Addressed as slave (IAAS bit set)
It will cause a processor interrupt request if the IBIE bit is set. This bit must be cleared by software, writing a one
to it. A write of 0 has no effect on this bit.
0
RXAK Received Acknowledge — The value of SDA during the acknowledge bit of a bus cycle. If the received
acknowledge bit (RXAK) is low, it indicates an acknowledge signal has been received after the completion of 8
bits data transmission on the bus. If RXAK is high, it means no acknowledge signal is detected at the 9th clock.
0 Acknowledge received
1 No acknowledge received
Table 8-7. IBSR Field Descriptions (continued)
Field Description
Chapter 8 Inter-Integrated Circuit (IICV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
264 Freescale Semiconductor
8.3.2.5 IIC Data I/O Register (IBDR)
In master transmit mode, when data is written to the IBDR a data transfer is initiated. The most significant
bit is sent first. In master receive mode, reading this register initiates next byte data receiving. In slave
mode, the same functions are available after an address match has occurred.Note that the Tx/Rx bit in the
IBCR must correctly reflect the desired direction of transfer in master and slave modes for the transmission
to begin. For instance, if the IIC is configured for master transmit but a master receive is desired, then
reading the IBDR will not initiate the receive.
Reading the IBDR will return the last byte received while the IIC is configured in either master receive or
slave receive modes. The IBDR does not reflect every byte that is transmitted on the IIC bus, nor can
software verify that a byte has been written to the IBDR correctly by reading it back.
In master transmit mode, the first byte of data written to IBDR following assertion of MS/SL is used for
the address transfer and should com.prise of the calling address (in position D7:D1) concatenated with the
required R/W bit (in position D0).
8.4 Functional Description
This section provides a complete functional description of the IICV2.
8.4.1 I-Bus Protocol
The IIC bus system uses a serial data line (SDA) and a serial clock line (SCL) for data transfer. All devices
connected to it must have open drain or open collector outputs. Logic AND function is exercised on both
lines with external pull-up resistors. The value of these resistors is system dependent.
Normally, a standard communication is composed of four parts: START signal, slave address transmission,
data transfer and STOP signal. They are described briefly in the following sections and illustrated in
Figure 8-9.
Offset Module Base + 0x0004
76543210
RD7 D6 D5 D4 D3 D2 D1 D0
W
Reset 0 0 0 00000
Figure 8-8. IIC Bus Data I/O Register (IBDR)
Chapter 8 Inter-Integrated Circuit (IICV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 265
Figure 8-9. IIC-Bus Transmission Signals
8.4.1.1 START Signal
When the bus is free, i.e. no master device is engaging the bus (both SCL and SDA lines are at logical
high), a master may initiate communication by sending a START signal.As shown in Figure 8-9, a START
signal is defined as a high-to-low transition of SDA while SCL is high. This signal denotes the beginning
of a new data transfer (each data transfer may contain several bytes of data) and brings all slaves out of
their idle states.
Figure 8-10. Start and Stop Conditions
SCL
SDA
Start
Signal
Ack
Bit
12345678
MSB LSB
12345678
MSB LSB
Stop
Signal
No
SCL
SDA
1234567 8
MSB LSB
1 2 5 678
MSB LSB
Repeated
34
99
AD7 AD6 AD5 AD4 AD3 AD2 AD1 R/W XXX D7 D6 D5 D4 D3 D2 D1 D0
Calling Address Read/ Data Byte
AD7 AD6 AD5 AD4 AD3 AD2 AD1 R/W AD7 AD6 AD5 AD4 AD3 AD2 AD1 R/W
New Calling Address
99
XX
Ack
Bit
Write
Start
Signal
Start
Signal
Ack
Bit
Calling Address Read/
Write
Stop
Signal
No
Ack
Bit
Read/
Write
SDA
SCL
START Condition STOP Condition
Chapter 8 Inter-Integrated Circuit (IICV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
266 Freescale Semiconductor
8.4.1.2 Slave Address Transmission
The first byte of data transfer immediately after the START signal is the slave address transmitted by the
master. This is a seven-bit calling address followed by a R/W bit. The R/W bit tells the slave the desired
direction of data transfer.
1 = Read transfer, the slave transmits data to the master.
0 = Write transfer, the master transmits data to the slave.
Only the slave with a calling address that matches the one transmitted by the master will respond by
sending back an acknowledge bit. This is done by pulling the SDA low at the 9th clock (see Figure 8-9).
No two slaves in the system may have the same address. If the IIC bus is master, it must not transmit an
address that is equal to its own slave address. The IIC bus cannot be master and slave at the same
time.However, if arbitration is lost during an address cycle the IIC bus will revert to slave mode and operate
correctly even if it is being addressed by another master.
8.4.1.3 Data Transfer
As soon as successful slave addressing is achieved, the data transfer can proceed byte-by-byte in a
direction specified by the R/W bit sent by the calling master
All transfers that come after an address cycle are referred to as data transfers, even if they carry sub-address
information for the slave device.
Each data byte is 8 bits long. Data may be changed only while SCL is low and must be held stable while
SCL is high as shown in Figure 8-9. There is one clock pulse on SCL for each data bit, the MSB being
transferred first. Each data byte has to be followed by an acknowledge bit, which is signalled from the
receiving device by pulling the SDA low at the ninth clock. So one complete data byte transfer needs nine
clock pulses.
If the slave receiver does not acknowledge the master, the SDA line must be left high by the slave. The
master can then generate a stop signal to abort the data transfer or a start signal (repeated start) to
commence a new calling.
If the master receiver does not acknowledge the slave transmitter after a byte transmission, it means 'end
of data' to the slave, so the slave releases the SDA line for the master to generate STOP or START signal.
8.4.1.4 STOP Signal
The master can terminate the communication by generating a STOP signal to free the bus. However, the
master may generate a START signal followed by a calling command without generating a STOP signal
first. This is called repeated START. A STOP signal is defined as a low-to-high transition of SDA while
SCL at logical 1 (see Figure 8-9).
The master can generate a STOP even if the slave has generated an acknowledge at which point the slave
must release the bus.
Chapter 8 Inter-Integrated Circuit (IICV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 267
8.4.1.5 Repeated START Signal
As shown in Figure 8-9, a repeated START signal is a START signal generated without first generating a
STOP signal to terminate the communication. This is used by the master to communicate with another
slave or with the same slave in different mode (transmit/receive mode) without releasing the bus.
8.4.1.6 Arbitration Procedure
The Inter-IC bus is a true multi-master bus that allows more than one master to be connected on it. If two
or more masters try to control the bus at the same time, a clock synchronization procedure determines the
bus clock, for which the low period is equal to the longest clock low period and the high is equal to the
shortest one among the masters. The relative priority of the contending masters is determined by a data
arbitration procedure, a bus master loses arbitration if it transmits logic 1 while another master transmits
logic 0. The losing masters immediately switch over to slave receive mode and stop driving SDA output.
In this case the transition from master to slave mode does not generate a STOP condition. Meanwhile, a
status bit is set by hardware to indicate loss of arbitration.
8.4.1.7 Clock Synchronization
Because wire-AND logic is performed on SCL line, a high-to-low transition on SCL line affects all the
devices connected on the bus. The devices start counting their low period and as soon as a device's clock
has gone low, it holds the SCL line low until the clock high state is reached.However, the change of low to
high in this device clock may not change the state of the SCL line if another device clock is within its low
period. Therefore, synchronized clock SCL is held low by the device with the longest low period. Devices
with shorter low periods enter a high wait state during this time (see Figure 8-10). When all devices
concerned have counted off their low period, the synchronized clock SCL line is released and pulled high.
There is then no difference between the device clocks and the state of the SCL line and all the devices start
counting their high periods.The first device to complete its high period pulls the SCL line low again.
Figure 8-11. IIC-Bus Clock Synchronization
SCL1
SCL2
SCL
Internal Counter Reset
WAIT Start Counting High Period
Chapter 8 Inter-Integrated Circuit (IICV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
268 Freescale Semiconductor
8.4.1.8 Handshaking
The clock synchronization mechanism can be used as a handshake in data transfer. Slave devices may hold
the SCL low after completion of one byte transfer (9 bits). In such case, it halts the bus clock and forces
the master clock into wait states until the slave releases the SCL line.
8.4.1.9 Clock Stretching
The clock synchronization mechanism can be used by slaves to slow down the bit rate of a transfer. After
the master has driven SCL low the slave can drive SCL low for the required period and then release it.If
the slave SCL low period is greater than the master SCL low period then the resulting SCL bus signal low
period is stretched.
8.4.2 Operation in Run Mode
This is the basic mode of operation.
8.4.3 Operation in Wait Mode
IIC operation in wait mode can be configured. Depending on the state of internal bits, the IIC can operate
normally when the CPU is in wait mode or the IIC clock generation can be turned off and the IIC module
enters a power conservation state during wait mode. In the later case, any transmission or reception in
progress stops at wait mode entry.
8.4.4 Operation in Stop Mode
The IIC is inactive in stop mode for reduced power consumption. The STOP instruction does not affect IIC
register states.
8.5 Resets
The reset state of each individual bit is listed in Section 8.3, “Memory Map and Register Definition, which
details the registers and their bit-fields.
8.6 Interrupts
IICV2 uses only one interrupt vector.
Table 8-8. Interrupt Summary
Internally there are three types of interrupts in IIC. The interrupt service routine can determine the interrupt
type by reading the status register.
Interrupt Offset Vector Priority Source Description
IIC
Interrupt IBAL, TCF,IAAS
bits in IBSR
register
When either of IBAL, TCF or IAAS bits is set
may cause an interrupt based on arbitration
lost, transfer complete or address detect
conditions
Chapter 8 Inter-Integrated Circuit (IICV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 269
IIC Interrupt can be generated on
1. Arbitration lost condition (IBAL bit set)
2. Byte transfer condition (TCF bit set)
3. Address detect condition (IAAS bit set)
The IIC interrupt is enabled by the IBIE bit in the IIC control register. It must be cleared by writing 0 to
the IBF bit in the interrupt service routine.
8.7 Initialization/Application Information
8.7.1 IIC Programming Examples
8.7.1.1 Initialization Sequence
Reset will put the IIC bus control register to its default status. Before the interface can be used to transfer
serial data, an initialization procedure must be carried out, as follows:
1. Update the frequency divider register (IBFD) and select the required division ratio to obtain SCL
frequency from system clock.
2. Update the IIC bus address register (IBAD) to define its slave address.
3. Set the IBEN bit of the IIC bus control register (IBCR) to enable the IIC interface system.
4. Modify the bits of the IIC bus control register (IBCR) to select master/slave mode, transmit/receive
mode and interrupt enable or not.
8.7.1.2 Generation of START
After completion of the initialization procedure, serial data can be transmitted by selecting the 'master
transmitter' mode. If the device is connected to a multi-master bus system, the state of the IIC bus busy bit
(IBB) must be tested to check whether the serial bus is free.
If the bus is free (IBB=0), the start condition and the first byte (the slave address) can be sent. The data
written to the data register comprises the slave calling address and the LSB set to indicate the direction of
transfer required from the slave.
The bus free time (i.e., the time between a STOP condition and the following START condition) is built
into the hardware that generates the START cycle. Depending on the relative frequencies of the system
clock and the SCL period it may be necessary to wait until the IIC is busy after writing the calling address
to the IBDR before proceeding with the following instructions. This is illustrated in the following example.
An example of a program which generates the START signal and transmits the first byte of data (slave
address) is shown below:
CHFLAG BRSET IBSR,#$20,* ;WAIT FOR IBB FLAG TO CLEAR
TXSTART BSET IBCR,#$30 ;SET TRANSMIT AND MASTER MODE;i.e. GENERATE START CONDITION
MOVB CALLING,IBDR ;TRANSMIT THE CALLING ADDRESS, D0=R/W
IBFREE BRCLR IBSR,#$20,* ;WAIT FOR IBB FLAG TO SET
Chapter 8 Inter-Integrated Circuit (IICV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
270 Freescale Semiconductor
8.7.1.3 Post-Transfer Software Response
Transmission or reception of a byte will set the data transferring bit (TCF) to 1, which indicates one byte
communication is finished. The IIC bus interrupt bit (IBIF) is set also; an interrupt will be generated if the
interrupt function is enabled during initialization by setting the IBIE bit. Software must clear the IBIF bit
in the interrupt routine first. The TCF bit will be cleared by reading from the IIC bus data I/O register
(IBDR) in receive mode or writing to IBDR in transmit mode.
Software may service the IIC I/O in the main program by monitoring the IBIF bit if the interrupt function
is disabled. Note that polling should monitor the IBIF bit rather than the TCF bit because their operation
is different when arbitration is lost.
Note that when an interrupt occurs at the end of the address cycle the master will always be in transmit
mode, i.e. the address is transmitted. If master receive mode is required, indicated by R/W bit in IBDR,
then the Tx/Rx bit should be toggled at this stage.
During slave mode address cycles (IAAS=1), the SRW bit in the status register is read to determine the
direction of the subsequent transfer and the Tx/Rx bit is programmed accordingly. For slave mode data
cycles (IAAS=0) the SRW bit is not valid, the Tx/Rx bit in the control register should be read to determine
the direction of the current transfer.
The following is an example of a software response by a 'master transmitter' in the interrupt routine.
8.7.1.4 Generation of STOP
A data transfer ends with a STOP signal generated by the 'master' device. A master transmitter can simply
generate a STOP signal after all the data has been transmitted. The following is an example showing how
a stop condition is generated by a master transmitter.
If a master receiver wants to terminate a data transfer, it must inform the slave transmitter by not
acknowledging the last byte of data which can be done by setting the transmit acknowledge bit (TXAK)
before reading the 2nd last byte of data. Before reading the last byte of data, a STOP signal must be
generated first. The following is an example showing how a STOP signal is generated by a master receiver.
ISR BCLR IBSR,#$02 ;CLEAR THE IBIF FLAG
BRCLR IBCR,#$20,SLAVE ;BRANCH IF IN SLAVE MODE
BRCLR IBCR,#$10,RECEIVE ;BRANCH IF IN RECEIVE MODE
BRSET IBSR,#$01,END ;IF NO ACK, END OF TRANSMISSION
TRANSMIT MOVB DATABUF,IBDR ;TRANSMIT NEXT BYTE OF DATA
MASTX TST TXCNT ;GET VALUE FROM THE TRANSMITING COUNTER
BEQ END ;END IF NO MORE DATA
BRSET IBSR,#$01,END ;END IF NO ACK
MOVB DATABUF,IBDR ;TRANSMIT NEXT BYTE OF DATA
DEC TXCNT ;DECREASE THE TXCNT
BRA EMASTX ;EXIT
END BCLR IBCR,#$20 ;GENERATE A STOP CONDITION
EMASTX RTI ;RETURN FROM INTERRUPT
Chapter 8 Inter-Integrated Circuit (IICV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 271
8.7.1.5 Generation of Repeated START
At the end of data transfer, if the master continues to want to communicate on the bus, it can generate
another START signal followed by another slave address without first generating a STOP signal. A
program example is as shown.
8.7.1.6 Slave Mode
In the slave interrupt service routine, the module addressed as slave bit (IAAS) should be tested to check
if a calling of its own address has just been received. If IAAS is set, software should set the transmit/receive
mode select bit (Tx/Rx bit of IBCR) according to the R/W command bit (SRW). Writing to the IBCR
clears the IAAS automatically. Note that the only time IAAS is read as set is from the interrupt at the end
of the address cycle where an address match occurred, interrupts resulting from subsequent data transfers
will have IAAS cleared. A data transfer may now be initiated by writing information to IBDR, for slave
transmits, or dummy reading from IBDR, in slave receive mode. The slave will drive SCL low in-between
byte transfers, SCL is released when the IBDR is accessed in the required mode.
In slave transmitter routine, the received acknowledge bit (RXAK) must be tested before transmitting the
next byte of data. Setting RXAK means an 'end of data' signal from the master receiver, after which it must
be switched from transmitter mode to receiver mode by software. A dummy read then releases the SCL
line so that the master can generate a STOP signal.
8.7.1.7 Arbitration Lost
If several masters try to engage the bus simultaneously, only one master wins and the others lose
arbitration. The devices which lost arbitration are immediately switched to slave receive mode by the
hardware. Their data output to the SDA line is stopped, but SCL continues to be generated until the end of
the byte during which arbitration was lost. An interrupt occurs at the falling edge of the ninth clock of this
transfer with IBAL=1 and MS/SL=0. If one master attempts to start transmission while the bus is being
engaged by another master, the hardware will inhibit the transmission; switch the MS/SL bit from 1 to 0
without generating STOP condition; generate an interrupt to CPU and set the IBAL to indicate that the
attempt to engage the bus is failed. When considering these cases, the slave service routine should test the
IBAL first and the software should clear the IBAL bit if it is set.
MASR DEC RXCNT ;DECREASE THE RXCNT
BEQ ENMASR ;LAST BYTE TO BE READ
MOVB RXCNT,D1 ;CHECK SECOND LAST BYTE
DEC D1 ;TO BE READ
BNE NXMAR ;NOT LAST OR SECOND LAST
LAMAR BSET IBCR,#$08 ;SECOND LAST, DISABLE ACK
;TRANSMITTING
BRA NXMAR
ENMASR BCLR IBCR,#$20 ;LAST ONE, GENERATE ‘STOP’ SIGNAL
NXMAR MOVB IBDR,RXBUF ;READ DATA AND STORE
RTI
RESTART BSET IBCR,#$04 ;ANOTHER START (RESTART)
MOVB CALLING,IBDR ;TRANSMIT THE CALLING ADDRESS;D0=R/W
Chapter 8 Inter-Integrated Circuit (IICV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
272 Freescale Semiconductor
Figure 8-12. Flow-Chart of Typical IIC Interrupt Routine
Clear
Master
Mode
?
Tx/Rx
?
Last Byte
Transmitted
?
RXAK=0
?
End Of
Addr Cycle
(Master Rx)
?
Write Next
Byte To IBDR
Switch To
Rx Mode
Dummy Read
From IBDR
Generate
Stop Signal
Read Data
From IBDR
And Store
Set TXAK =1 Generate
Stop Signal
2nd Last
Byte To Be Read
?
Last
Byte To Be Read
?
Arbitration
Lost
?
Clear IBAL
IAAS=1
?
IAAS=1
?
SRW=1
?
TX/RX
?
Set TX
Mode
Write Data
To IBDR
Set RX
Mode
Dummy Read
From IBDR
ACK From
Receiver
?
Tx Next
Byte
Read Data
From IBDR
And Store
Switch To
Rx Mode
Dummy Read
From IBDR
RTI
YN
Y
YY
Y
Y
Y
Y
Y
Y
N
N
N
N
N
N
N
N
N
Y
TX RX
RX
TX
(Write)
(Read)
N
IBIF
Address Transfer Data Transfer
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 273
Chapter 9
Freescale’s Scalable Controller Area Network
(S12MSCANV2)
9.1 Introduction
Freescale’s scalable controller area network (S12MSCANV2) definition is based on the MSCAN12
definition, which is the specific implementation of the MSCAN concept targeted for the M68HC12
microcontroller family.
The module is a communication controller implementing the CAN 2.0A/B protocol as defined in the
Bosch specification dated September 1991. For users to fully understand the MSCAN specification, it is
recommended that the Bosch specification be read first to familiarize the reader with the terms and
concepts contained within this document.
Though not exclusively intended for automotive applications, CAN protocol is designed to meet the
specific requirements of a vehicle serial data bus: real-time processing, reliable operation in the EMI
environment of a vehicle, cost-effectiveness, and required bandwidth.
MSCAN uses an advanced buffer arrangement resulting in predictable real-time behavior and simplified
application software.
9.1.1 Glossary
ACK: Acknowledge of CAN message
CAN: Controller Area Network
CRC: Cyclic Redundancy Code
EOF: End of Frame
FIFO: First-In-First-Out Memory
IFS: Inter-Frame Sequence
SOF: Start of Frame
CPU bus: CPU related read/write data bus
CAN bus: CAN protocol related serial bus
oscillator clock: Direct clock from external oscillator
bus clock: CPU bus realated clock
CAN clock: CAN protocol related clock
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
274 Freescale Semiconductor
9.1.2 Block Diagram
Figure 9-1. MSCAN Block Diagram
9.1.3 Features
The basic features of the MSCAN are as follows:
Implementation of the CAN protocol — Version 2.0A/B
Standard and extended data frames
Zero to eight bytes data length
Programmable bit rate up to 1 Mbps1
Support for remote frames
Five receive buffers with FIFO storage scheme
Three transmit buffers with internal prioritization using a “local priority” concept
Flexible maskable identifier filter supports two full-size (32-bit) extended identifier filters, or four
16-bit filters, or eight 8-bit filters
Programmable wakeup functionality with integrated low-pass filter
Programmable loopback mode supports self-test operation
Programmable listen-only mode for monitoring of CAN bus
Separate signalling and interrupt capabilities for all CAN receiver and transmitter error states
(warning, error passive, bus-off)
Programmable MSCAN clock source either bus clock or oscillator clock
Internal timer for time-stamping of received and transmitted messages
Three low-power modes: sleep, power down, and MSCAN enable
1. Depending on the actual bit timing and the clock jitter of the PLL.
RXCAN
TXCAN
Receive/
Transmit
Engine
Message
Filtering
and
Buffering
Control
and
Status
Wake-Up Interrupt Req.
Errors Interrupt Req.
Receive Interrupt Req.
Transmit Interrupt Req.
CANCLK
Bus Clock
Configuration
Oscillator Clock
MUX
Presc.
Tq Clk
MSCAN
Low Pass Filter
Wake-Up
Registers
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 275
Global initialization of configuration registers
9.1.4 Modes of Operation
The following modes of operation are specific to the MSCAN. See Section 9.4, “Functional Description,”
for details.
Listen-Only Mode
MSCAN Sleep Mode
MSCAN Initialization Mode
MSCAN Power Down Mode
9.2 External Signal Description
The MSCAN uses two external pins:
9.2.1 RXCAN — CAN Receiver Input Pin
RXCAN is the MSCAN receiver input pin.
9.2.2 TXCAN — CAN Transmitter Output Pin
TXCAN is the MSCAN transmitter output pin. The TXCAN output pin represents the logic level on the
CAN bus:
0 = Dominant state
1 = Recessive state
9.2.3 CAN System
A typical CAN system with MSCAN is shown in Figure 9-2. Each CAN station is connected physically
to the CAN bus lines through a transceiver device. The transceiver is capable of driving the large current
needed for the CAN bus and has current protection against defective CAN or defective stations.
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
276 Freescale Semiconductor
Figure 9-2. CAN System
9.3 Memory Map and Register Definition
This section provides a detailed description of all registers accessible in the MSCAN.
9.3.1 Module Memory Map
Figure 9-3 gives an overview on all registers and their individual bits in the MSCAN memory map. The
register address results from the addition of base address and address offset. The base address is
determined at the MCU level and can be found in the MCU memory map description. The address offset
is defined at the module level.
The MSCAN occupies 64 bytes in the memory space. The base address of the MSCAN module is
determined at the MCU level when the MCU is defined. The register decode map is fixed and begins at the
first address of the module address offset.
The detailed register descriptions follow in the order they appear in the register map.
CAN Bus
CAN Controller
(MSCAN)
Transceiver
CAN node 1 CAN node 2 CAN node n
CAN_L
CAN_H
MCU
TXCAN RXCAN
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 277
Register
Name Bit 7 6 5 4 3 2 1 Bit 0
0x0000
CANCTL0 RRXFRM RXACT CSWAI SYNCH TIME WUPE SLPRQ INITRQ
W
0x0001
CANCTL1 RCANE CLKSRC LOOPB LISTEN WUPM SLPAK INITAK
W
0x0002
CANBTR0 RSJW1 SJW0 BRP5 BRP4 BRP3 BRP2 BRP1 BRP0
W
0x0003
CANBTR1 RSAMP TSEG22 TSEG21 TSEG20 TSEG13 TSEG12 TSEG11 TSEG10
W
0x0004
CANRFLG RWUPIF CSCIF RSTAT1 RSTAT0 TSTAT1 TSTAT0 OVRIF RXF
W
0x0005
CANRIER RWUPIE CSCIE RSTATE1 RSTATE0 TSTATE1 TSTATE0 OVRIE RXFIE
W
0x0006
CANTFLG R0 0000
TXE2 TXE1 TXE0
W
0x0007
CANTIER R00000
TXEIE2 TXEIE1 TXEIE0
W
0x0008
CANTARQ R00000
ABTRQ2 ABTRQ1 ABTRQ0
W
0x0009
CANTAAK R00000ABTAK2 ABTAK1 ABTAK0
W
0x000A
CANTBSEL R00000
TX2 TX1 TX0
W
0x000B
CANIDAC R0 0 IDAM1 IDAM0 0 IDHIT2 IDHIT1 IDHIT0
W
0x000C–0x000D
Reserved R00000000
W
0x000E
CANRXERR R RXERR7 RXERR6 RXERR5 RXERR4 RXERR3 RXERR2 RXERR1 RXERR0
W
0x000F
CANTXERR R TXERR7 TXERR6 TXERR5 TXERR4 TXERR3 TXERR2 TXERR1 TXERR0
W
= Unimplemented or Reserved u = Unaffected
Figure 9-3. MSCAN Register Summary
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
278 Freescale Semiconductor
9.3.2 Register Descriptions
This section describes in detail all the registers and register bits in the MSCAN module. Each description
includes a standard register diagram with an associated figure number. Details of register bit and field
function follow the register diagrams, in bit order. All bits of all registers in this module are completely
synchronous to internal clocks during a register read.
9.3.2.1 MSCAN Control Register 0 (CANCTL0)
The CANCTL0 register provides various control bits of the MSCAN module as described below.
0x0010–0x0013
CANIDAR0–3 RAC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0
W
0x0014–0x0017
CANIDMRx RAM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0
W
0x0018–0x001B
CANIDAR4–7 RAC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0
W
0x001C–0x001F
CANIDMR4–7 RAM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0
W
0x0020–0x002F
CANRXFG RSee Section 9.3.3, “Programmer’s Model of Message Storage
W
0x0030–0x003F
CANTXFG RSee Section 9.3.3, “Programmer’s Model of Message Storage
W
Module Base + 0x0000
76543210
RRXFRM RXACT CSWAI SYNCH TIME WUPE SLPRQ INITRQ
W
Reset: 00000001
= Unimplemented
Figure 9-4. MSCAN Control Register 0 (CANCTL0)
Register
Name Bit 7 6 5 4 3 2 1 Bit 0
= Unimplemented or Reserved u = Unaffected
Figure 9-3. MSCAN Register Summary (continued)
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 279
NOTE
The CANCTL0 register, except WUPE, INITRQ, and SLPRQ, is held in the
reset state when the initialization mode is active (INITRQ = 1 and
INITAK = 1). This register is writable again as soon as the initialization
mode is exited (INITRQ = 0 and INITAK = 0).
Read: Anytime
Write: Anytime when out of initialization mode; exceptions are read-only RXACT and SYNCH, RXFRM
(which is set by the module only), and INITRQ (which is also writable in initialization mode).
Table 9-1. CANCTL0 Register Field Descriptions
Field Description
7
RXFRM1Received Frame Flag This bit is read and clear only. It is set when a receiver has received a valid message
correctly, independently of the filter configuration. After it is set, it remains set until cleared by software or reset.
Clearing is done by writing a 1. Writing a 0 is ignored. This bit is not valid in loopback mode.
0 No valid message was received since last clearing this flag
1 A valid message was received since last clearing of this flag
6
RXACT Receiver Active Status — This read-only flag indicates the MSCAN is receiving a message. The flag is
controlled by the receiver front end. This bit is not valid in loopback mode.
0 MSCAN is transmitting or idle2
1 MSCAN is receiving a message (including when arbitration is lost)2
5
CSWAI3CAN Stops in Wait Mode Enabling this bit allows for lower power consumption in wait mode by disabling all
the clocks at the CPU bus interface to the MSCAN module.
0 The module is not affected during wait mode
1 The module ceases to be clocked during wait mode
4
SYNCH Synchronized Status This read-only flag indicates whether the MSCAN is synchronized to the CAN bus and
able to participate in the communication process. It is set and cleared by the MSCAN.
0 MSCAN is not synchronized to the CAN bus
1 MSCAN is synchronized to the CAN bus
3
TIME Timer Enable This bit activates an internal 16-bit wide free running timer which is clocked by the bit clock rate.
If the timer is enabled, a 16-bit time stamp will be assigned to each transmitted/received message within the
active TX/RX buffer. Right after the EOF of a valid message on the CAN bus, the time stamp is written to the
highest bytes (0x000E, 0x000F) in the appropriate buffer (see Section 9.3.3, “Programmer’s Model of Message
Storage”). The internal timer is reset (all bits set to 0) when disabled. This bit is held low in initialization mode.
0 Disable internal MSCAN timer
1 Enable internal MSCAN timer
2
WUPE4Wake-Up Enable This configuration bit allows the MSCAN to restart from sleep mode when traffic on CAN is
detected (see Section 9.4.5.4, “MSCAN Sleep Mode”).
0 Wake-up disabled — The MSCAN ignores traffic on CAN
1 Wake-up enabled — The MSCAN is able to restart
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
280 Freescale Semiconductor
9.3.2.2 MSCAN Control Register 1 (CANCTL1)
The CANCTL1 register provides various control bits and handshake status information of the MSCAN
module as described below.
1
SLPRQ5Sleep Mode Request — This bit requests the MSCAN to enter sleep mode, which is an internal power saving
mode (see Section 9.4.5.4, “MSCAN Sleep Mode”). The sleep mode request is serviced when the CAN bus is
idle, i.e., the module is not receiving a message and all transmit buffers are empty. The module indicates entry
to sleep mode by setting SLPAK = 1 (see Section 9.3.2.2, “MSCAN Control Register 1 (CANCTL1)”). SLPRQ
cannot be set while the WUPIF flag is set (see Section 9.3.2.5, “MSCAN Receiver Flag Register (CANRFLG)”).
Sleep mode will be active until SLPRQ is cleared by the CPU or, depending on the setting of WUPE, the MSCAN
detects activity on the CAN bus and clears SLPRQ itself.
0 Running — The MSCAN functions normally
1 Sleep mode request — The MSCAN enters sleep mode when CAN bus idle
0
INITRQ6,7 Initialization Mode Request — When this bit is set by the CPU, the MSCAN skips to initialization mode (see
Section 9.4.5.5, “MSCAN Initialization Mode”). Any ongoing transmission or reception is aborted and
synchronization to the CAN bus is lost. The module indicates entry to initialization mode by setting INITAK = 1
(Section 9.3.2.2, “MSCAN Control Register 1 (CANCTL1)”).
The following registers enter their hard reset state and restore their default values: CANCTL08, CANRFLG9,
CANRIER10, CANTFLG, CANTIER, CANTARQ, CANTAAK, and CANTBSEL.
The registers CANCTL1, CANBTR0, CANBTR1, CANIDAC, CANIDAR0-7, and CANIDMR0-7 can only be
written by the CPU when the MSCAN is in initialization mode (INITRQ = 1 and INITAK = 1). The values of the
error counters are not affected by initialization mode.
When this bit is cleared by the CPU, the MSCAN restarts and then tries to synchronize to the CAN bus. If the
MSCAN is not in bus-off state, it synchronizes after 11 consecutive recessive bits on the CAN bus; if the MSCAN
is in bus-off state, it continues to wait for 128 occurrences of 11 consecutive recessive bits.
Writing to otherbits in CANCTL0, CANRFLG, CANRIER, CANTFLG, or CANTIER must be done only after
initialization mode is exited, which is INITRQ = 0 and INITAK = 0.
0 Normal operation
1 MSCAN in initialization mode
1The MSCAN must be in normal mode for this bit to become set.
2See the Bosch CAN 2.0A/B specification for a detailed definition of transmitter and receiver states.
3In order to protect from accidentally violating the CAN protocol, the TXCAN pin is immediately forced to a recessive state when
the CPU enters wait (CSWAI = 1) or stop mode (see Section 9.4.5.2,“Operation in WaitMode and Section 9.4.5.3, “Operation
in Stop Mode”).
4The CPU has to make sure that the WUPE register and the WUPIE wake-up interrupt enable register (see Section 9.3.2.6,
“MSCAN Receiver Interrupt Enable Register (CANRIER)) is enabled, if the recovery mechanism from stop or wait is required.
5The CPU cannot clear SLPRQ before the MSCAN has entered sleep mode (SLPRQ = 1 and SLPAK = 1).
6The CPU cannot clear INITRQ before the MSCAN has entered initialization mode (INITRQ = 1 and INITAK = 1).
7In order to protect from accidentally violating the CAN protocol, the TXCAN pin is immediately forced to a recessive state when
the initialization mode is requested by the CPU. Thus, the recommended procedure is to bring the MSCAN into sleep mode
(SLPRQ = 1 and SLPAK = 1) before requesting initialization mode.
8Not including WUPE, INITRQ, and SLPRQ.
9TSTAT1 and TSTAT0 are not affected by initialization mode.
10 RSTAT1 and RSTAT0 are not affected by initialization mode.
Table 9-1. CANCTL0 Register Field Descriptions (continued)
Field Description
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 281
Read: Anytime
Write: Anytime when INITRQ = 1 and INITAK = 1, except CANE which is write once in normal and
anytime in special system operation modes when the MSCAN is in initialization mode (INITRQ = 1 and
INITAK = 1).
Module Base + 0x0001
7 654 3 210
RCANE CLKSRC LOOPB LISTEN WUPM SLPAK INITAK
W
Reset: 0 0 0 1 0 0 0 1
= Unimplemented
Figure 9-5. MSCAN Control Register 1 (CANCTL1)
Table 9-2. CANCTL1 Register Field Descriptions
Field Description
7
CANE MSCAN Enable
0 MSCAN module is disabled
1 MSCAN module is enabled
6
CLKSRC MSCAN Clock Source This bit defines the clock source for the MSCAN module (only for systems with a clock
generation module; Section 9.4.3.2, “Clock System,” and Section Figure 9-42., “MSCAN Clocking Scheme,”).
0 MSCAN clock source is the oscillator clock
1 MSCAN clock source is the bus clock
5
LOOPB Loopback Self Test Mode When this bit is set, the MSCAN performs an internal loopback which can be used
for self test operation. The bit stream output of the transmitter is fed back to the receiver internally. The RXCAN
input pin is ignored and the TXCAN output goes to the recessive state (logic 1). The MSCAN behaves as it does
normally when transmitting and treats its own transmitted message as a message received from a remote node.
In this state, the MSCAN ignores the bit sent during the ACK slot in the CAN frame acknowledge field to ensure
proper reception of its own message. Both transmit and receive interrupts are generated.
0 Loopback self test disabled
1 Loopback self test enabled
4
LISTEN Listen Only Mode This bit configures the MSCAN as a CAN bus monitor. When LISTEN is set, all valid CAN
messages with matching ID are received, but no acknowledgement or error frames are sent out (see
Section 9.4.4.4, “Listen-Only Mode”). In addition, the error counters are frozen. Listen only mode supports
applications which require “hot plugging” or throughput analysis. The MSCAN is unable to transmit any
messages when listen only mode is active.
0 Normal operation
1 Listen only mode activated
2
WUPM Wake-Up Mode — If WUPE in CANCTL0 is enabled, this bit defines whether the integrated low-pass filter is
applied to protect the MSCAN from spurious wake-up (see Section 9.4.5.4, “MSCAN Sleep Mode”).
0 MSCAN wakes up on any dominant level on the CAN bus
1 MSCAN wakes up only in case of a dominant pulse on the CAN bus that has a length of Twup
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
282 Freescale Semiconductor
1
SLPAK Sleep Mode Acknowledge — This flag indicates whether the MSCAN module has entered sleep mode (see
Section 9.4.5.4, “MSCAN Sleep Mode”). It is used as a handshake flag for the SLPRQ sleep mode request.
Sleep mode is active when SLPRQ = 1 and SLPAK = 1. Depending on the setting of WUPE, the MSCAN will
clear the flag if it detects activity on the CAN bus while in sleep mode.
0 Running — The MSCAN operates normally
1 Sleep mode active — The MSCAN has entered sleep mode
0
INITAK Initialization Mode Acknowledge — This flag indicates whether the MSCAN module is in initialization mode
(see Section 9.4.5.5, “MSCAN Initialization Mode”). It is used as a handshake flag for the INITRQ initialization
mode request. Initialization mode is active when INITRQ = 1 and INITAK = 1. The registers CANCTL1,
CANBTR0,CANBTR1, CANIDAC,CANIDAR0–CANIDAR7, and CANIDMR0–CANIDMR7 canbewritten only by
the CPU when the MSCAN is in initialization mode.
0 Running — The MSCAN operates normally
1 Initialization mode active — The MSCAN has entered initialization mode
Table 9-2. CANCTL1 Register Field Descriptions (continued)
Field Description
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 283
9.3.2.3 MSCAN Bus Timing Register 0 (CANBTR0)
The CANBTR0 register configures various CAN bus timing parameters of the MSCAN module.
Read: Anytime
Write: Anytime in initialization mode (INITRQ = 1 and INITAK = 1)
Module Base + 0x0002
76543210
RSJW1 SJW0 BRP5 BRP4 BRP3 BRP2 BRP1 BRP0
W
Reset: 00000000
Figure 9-6. MSCAN Bus Timing Register 0 (CANBTR0)
Table 9-3. CANBTR0Register Field Descriptions
Field Description
7:6
SJW[1:0] Synchronization Jump Width The synchronization jump width defines the maximum number of time quanta
(Tq) clock cycles a bit can be shortened or lengthened to achieve resynchronization to data transitions on the
CAN bus (see Table 9-4).
5:0
BRP[5:0] Baud Rate Prescaler These bits determine the time quanta (Tq) clock which is used to build up the bit timing
(see Table 9-5).
Table 9-4. Synchronization Jump Width
SJW1 SJW0 Synchronization Jump Width
0 0 1 Tq clock cycle
0 1 2 Tq clock cycles
1 0 3 Tq clock cycles
1 1 4 Tq clock cycles
Table 9-5. Baud Rate Prescaler
BRP5 BRP4 BRP3 BRP2 BRP1 BRP0 Prescaler value (P)
000000 1
000001 2
000010 3
000011 4
:::::: :
111111 64
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
284 Freescale Semiconductor
9.3.2.4 MSCAN Bus Timing Register 1 (CANBTR1)
The CANBTR1 register configures various CAN bus timing parameters of the MSCAN module.
Read: Anytime
Write: Anytime in initialization mode (INITRQ = 1 and INITAK = 1)
Module Base + 0x0003
76543210
RSAMP TSEG22 TSEG21 TSEG20 TSEG13 TSEG12 TSEG11 TSEG10
W
Reset: 00000000
Figure 9-7. MSCAN Bus Timing Register 1 (CANBTR1)
Table 9-6. CANBTR1 Register Field Descriptions
Field Description
7
SAMP Sampling — This bit determines the number of CAN bus samples taken per bit time.
0 One sample per bit.
1 Three samples per bit1.
If SAMP = 0, the resulting bit value is equal to the value of the single bit positioned at the sample point. If
SAMP = 1, the resulting bit value is determined by using majority rule on the three total samples. For higher bit
rates, it is recommended that only one sample is taken per bit time (SAMP = 0).
1In this case, PHASE_SEG1 must be at least 2 time quanta (Tq).
6:4
TSEG2[2:0] Time Segment 2 Time segments within the bit time fix the number of clock cycles per bit time and the location
of the sample point (see Figure 9-43). Time segment 2 (TSEG2) values are programmable as shown in Table 9-7.
3:0
TSEG1[3:0] Time Segment 1 Time segments within the bit time fix the number of clock cycles per bit time and the location
of the sample point (see Figure 9-43). Time segment 1 (TSEG1) values are programmable as shown in Table 9-8.
Table 9-7. Time Segment 2 Values
TSEG22 TSEG21 TSEG20 Time Segment 2
0 0 0 1 Tq clock cycle1
1This setting is not valid. Please refer to Table 9-34 for valid settings.
0 0 1 2 Tq clock cycles
::: :
1 1 0 7 Tq clock cycles
1 1 1 8 Tq clock cycles
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 285
The bit time is determined by the oscillator frequency, the baud rate prescaler, and the number of time
quanta (Tq) clock cycles per bit (as shown in Table 9-7 and Table 9-8).
Eqn. 9-1
9.3.2.5 MSCAN Receiver Flag Register (CANRFLG)
A flag can be cleared only by software (writing a 1 to the corresponding bit position) when the condition
which caused the setting is no longer valid. Every flag has an associated interrupt enable bit in the
CANRIER register.
NOTE
The CANRFLG register is held in the reset state1 when the initialization
modeis active(INITRQ = 1 andINITAK = 1). Thisregisteriswritable again
as soon as the initialization mode is exited (INITRQ = 0 and INITAK = 0).
Read: Anytime
Write: Anytime when out of initialization mode, except RSTAT[1:0] and TSTAT[1:0] flags which are
read-only; write of 1 clears flag; write of 0 is ignored.
Table 9-8. Time Segment 1 Values
TSEG13 TSEG12 TSEG11 TSEG10 Time segment 1
0 0 0 0 1 Tq clock cycle1
1This setting is not valid. Please refer to Table 9-34 for valid settings.
0 0 0 1 2 Tq clock cycles1
0 0 1 0 3 Tq clock cycles1
0 0 1 1 4 Tq clock cycles
:::: :
1 1 1 0 15 Tq clock cycles
1 1 1 1 16 Tq clock cycles
Module Base + 0x0004
76543210
RWUPIF CSCIF RSTAT1 RSTAT0 TSTAT1 TSTAT0 OVRIF RXF
W
Reset: 00000000
= Unimplemented
Figure 9-8. MSCAN Receiver Flag Register (CANRFLG)
1. The RSTAT[1:0], TSTAT[1:0] bits are not affected by initialization mode.
Bit Time Prescaler value()
fCANCLK
------------------------------------------------------1 TimeSegment1 TimeSegment2++()=
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
286 Freescale Semiconductor
Table 9-9. CANRFLG Register Field Descriptions
Field Description
7
WUPIF Wake-Up Interrupt Flag — If the MSCAN detects CAN bus activity while in sleep mode (see Section 9.4.5.4,
“MSCAN Sleep Mode,”) and WUPE = 1 in CANTCTL0 (see Section 9.3.2.1, “MSCAN Control Register 0
(CANCTL0)”), the module will set WUPIF. If not masked, a wake-up interrupt is pending while this flag is set.
0 No wake-up activity observed while in sleep mode
1 MSCAN detected activity on the CAN bus and requested wake-up
6
CSCIF CAN Status Change Interrupt Flag — This flag is set when the MSCAN changes its current CAN bus status
due to the actual value of the transmit error counter (TEC) and the receive error counter (REC). An additional
4-bit (RSTAT[1:0], TSTAT[1:0]) status register, which is split into separate sections for TEC/REC, informs the
system on the actual CAN bus status (see Section 9.3.2.6, “MSCAN Receiver Interrupt Enable Register
(CANRIER)”). If not masked, an error interrupt is pending while this flag is set. CSCIF provides a blocking
interrupt. Thatguaranteesthatthe receiver/transmitterstatus bits(RSTAT/TSTAT)are onlyupdated whenno CAN
status change interrupt is pending. If the TECs/RECs change their current value after the CSCIF is asserted,
which would cause an additional state change in the RSTAT/TSTAT bits, these bits keep their status until the
current CSCIF interrupt is cleared again.
0 No change in CAN bus status occurred since last interrupt
1 MSCAN changed current CAN bus status
5:4
RSTAT[1:0] Receiver Status Bits — The values of the error counters control the actual CAN bus status of the MSCAN. As
soon as the status change interrupt flag (CSCIF) is set, these bits indicate the appropriate receiver related CAN
bus status of the MSCAN. The coding for the bits RSTAT1, RSTAT0 is:
00 RxOK: 0 receive error counter 96
01 RxWRN: 96 < receive error counter 127
10 RxERR: 127 < receive error counter
11 Bus-off1: transmit error counter > 255
1Redundant Information forthe most critical CAN bus status which is “bus-off”. This only occurs if the Tx error counter exceeds
a number of 255 errors. Bus-off affects the receiver state. As soon as the transmitter leaves its bus-off state the receiver state
skips to RxOK too. Refer also to TSTAT[1:0] coding in this register.
3:2
TSTAT[1:0] Transmitter Status Bits — The values of the error counters control the actual CAN bus status of the MSCAN.
As soon as the status change interrupt flag (CSCIF) is set, these bits indicate the appropriate transmitter related
CAN bus status of the MSCAN. The coding for the bits TSTAT1, TSTAT0 is:
00 TxOK: 0 transmit error counter 96
01 TxWRN: 96 < transmit error counter 127
10 TxERR: 127 < transmit error counter 255
11 Bus-Off: transmit error counter > 255
1
OVRIF Overrun Interrupt Flag This flag is set when a data overrun condition occurs. If not masked, an error interrupt
is pending while this flag is set.
0 No data overrun condition
1 A data overrun detected
0
RXF2
2To ensure data integrity, do not read the receive buffer registers while the RXF flag is cleared. For MCUs with dual CPUs,
reading the receive buffer registers while the RXF flag is cleared may result in a CPU fault condition.
Receive Buffer Full Flag RXF is set by the MSCAN when a new message is shifted in the receiver FIFO. This
flag indicates whether the shifted buffer is loaded with a correctly received message (matching identifier,
matching cyclic redundancy code (CRC) and no other errors detected). After the CPU has read that message
from the RxFG buffer in the receiver FIFO, the RXF flag must be cleared to release the buffer. A set RXF flag
prohibits the shifting of the next FIFO entry into the foreground buffer (RxFG). If not masked, a receive interrupt
is pending while this flag is set.
0 No new message available within the RxFG
1 The receiver FIFO is not empty. A new message is available in the RxFG
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 287
9.3.2.6 MSCAN Receiver Interrupt Enable Register (CANRIER)
This register contains the interrupt enable bits for the interrupt flags described in the CANRFLG register.
NOTE
TheCANRIER registeris held inthe reset statewhen the initializationmode
is active (INITRQ=1 and INITAK=1). This register is writable when not in
initialization mode (INITRQ=0 and INITAK=0).
The RSTATE[1:0], TSTATE[1:0] bits are not affected by initialization
mode.
Read: Anytime
Write: Anytime when not in initialization mode
Module Base + 0x0005
76543210
RWUPIE CSCIE RSTATE1 RSTATE0 TSTATE1 TSTATE0 OVRIE RXFIE
W
Reset: 00000000
Figure 9-9. MSCAN Receiver Interrupt Enable Register (CANRIER)
Table 9-10. CANRIER Register Field Descriptions
Field Description
7
WUPIE1Wake-Up Interrupt Enable
0 No interrupt request is generated from this event.
1 A wake-up event causes a Wake-Up interrupt request.
6
CSCIE CAN Status Change Interrupt Enable
0 No interrupt request is generated from this event.
1 A CAN Status Change event causes an error interrupt request.
5:4
RSTATE[1:0] Receiver Status Change Enable These RSTAT enable bits control the sensitivity level in which receiver state
changes are causing CSCIF interrupts. Independent of the chosen sensitivity level the RSTAT flags continue to
indicate the actual receiver state and are only updated if no CSCIF interrupt is pending.
00 Do not generate any CSCIF interrupt caused by receiver state changes.
01 Generate CSCIF interrupt only if the receiver enters or leaves “bus-off” state. Discard other receiver state
changes for generating CSCIF interrupt.
10 Generate CSCIF interrupt only if the receiver enters or leaves “RxErr” or “bus-off2 state. Discard other
receiver state changes for generating CSCIF interrupt.
11 Generate CSCIF interrupt on all state changes.
3:2
TSTATE[1:0] Transmitter Status Change Enable These TSTAT enable bits control the sensitivity level in which transmitter
state changes are causing CSCIF interrupts. Independent of the chosen sensitivity level, the TSTAT flags
continue to indicate the actual transmitter state and are only updated if no CSCIF interrupt is pending.
00 Do not generate any CSCIF interrupt caused by transmitter state changes.
01 Generate CSCIF interrupt only if the transmitter enters or leaves “bus-off” state. Discard other transmitter
state changes for generating CSCIF interrupt.
10 Generate CSCIF interrupt only if the transmitter enters or leaves “TxErr” or “bus-off” state. Discard other
transmitter state changes for generating CSCIF interrupt.
11 Generate CSCIF interrupt on all state changes.
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
288 Freescale Semiconductor
9.3.2.7 MSCAN Transmitter Flag Register (CANTFLG)
The transmit buffer empty flags each have an associated interrupt enable bit in the CANTIER register.
NOTE
The CANTFLG register is held in the reset state when the initialization
modeis active(INITRQ = 1 andINITAK = 1).This registeris writable when
not in initialization mode (INITRQ = 0 and INITAK = 0).
Read: Anytime
Write: Anytime for TXEx flags when not in initialization mode; write of 1 clears flag, write of 0 is ignored
1
OVRIE Overrun Interrupt Enable
0 No interrupt request is generated from this event.
1 An overrun event causes an error interrupt request.
0
RXFIE Receiver Full Interrupt Enable
0 No interrupt request is generated from this event.
1 A receive buffer full (successful message reception) event causes a receiver interrupt request.
1WUPIE and WUPE (see Section 9.3.2.1, “MSCAN Control Register 0 (CANCTL0)”) must both be enabled if the recovery
mechanism from stop or wait is required.
2Bus-off state is defined by the CAN standard (see Bosch CAN 2.0A/B protocol specification: for only transmitters. Because the
only possible state change for the transmitter from bus-off to TxOK also forces the receiver to skip its current state to RxOK,
the coding of the RXSTAT[1:0] flags define an additional bus-off state for the receiver (see Section 9.3.2.5, “MSCAN Receiver
Flag Register (CANRFLG)”).
Module Base + 0x0006
76543210
R0 0000
TXE2 TXE1 TXE0
W
Reset: 00000111
= Unimplemented
Figure 9-10. MSCAN Transmitter Flag Register (CANTFLG)
Table 9-10. CANRIER Register Field Descriptions (continued)
Field Description
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 289
9.3.2.8 MSCAN Transmitter Interrupt Enable Register (CANTIER)
This register contains the interrupt enable bits for the transmit buffer empty interrupt flags.
NOTE
TheCANTIERregister isheldin the reset state when theinitializationmode
is active (INITRQ = 1 and INITAK = 1). This register is writable when not
in initialization mode (INITRQ = 0 and INITAK = 0).
Read: Anytime
Write: Anytime when not in initialization mode
Table 9-11. CANTFLG Register Field Descriptions
Field Description
2:0
TXE[2:0] Transmitter Buffer Empty This flag indicates that the associated transmit message buffer is empty, and thus
not scheduled for transmission. The CPU must clear the flag after a message is set up in the transmit buffer and
is due for transmission. The MSCAN sets the flag after the message is sent successfully. The flag is also set by
the MSCAN when the transmission request is successfully aborted due to a pending abort request (see
Section 9.3.2.9, “MSCAN Transmitter Message Abort Request Register (CANTARQ)”). If not masked, a transmit
interrupt is pending while this flag is set.
Clearing a TXEx flag also clears the corresponding ABTAKx (see Section 9.3.2.10, “MSCAN Transmitter
Message Abort Acknowledge Register (CANTAAK)”). When a TXEx flag is set, the corresponding ABTRQx bit
is cleared (see Section 9.3.2.9, “MSCAN Transmitter Message Abort Request Register (CANTARQ)”).
When listen-mode is active (see Section 9.3.2.2, “MSCAN Control Register 1 (CANCTL1)”) the TXEx flags
cannot be cleared and no transmission is started.
Read and write accesses to the transmit buffer will be blocked, if the corresponding TXEx bit is cleared
(TXEx = 0) and the buffer is scheduled for transmission.
0 The associated message buffer is full (loaded with a message due for transmission)
1 The associated message buffer is empty (not scheduled)
Module Base + 0x0007
76543210
R00000
TXEIE2 TXEIE1 TXEIE0
W
Reset: 00000000
= Unimplemented
Figure 9-11. MSCAN Transmitter Interrupt Enable Register (CANTIER)
Table 9-12. CANTIER Register Field Descriptions
Field Description
2:0
TXEIE[2:0] Transmitter Empty Interrupt Enable
0 No interrupt request is generated from this event.
1 A transmitter empty (transmit buffer available for transmission) event causes a transmitter empty interrupt
request.
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
290 Freescale Semiconductor
9.3.2.9 MSCAN Transmitter Message Abort Request Register (CANTARQ)
The CANTARQ register allows abort request of queued messages as described below.
NOTE
The CANTARQ register is held in the reset state when the initialization
modeis active(INITRQ = 1 andINITAK = 1).This registeris writable when
not in initialization mode (INITRQ = 0 and INITAK = 0).
Read: Anytime
Write: Anytime when not in initialization mode
Module Base + 0x0008
76543210
R00000
ABTRQ2 ABTRQ1 ABTRQ0
W
Reset: 00000000
= Unimplemented
Figure 9-12. MSCAN Transmitter Message Abort Request Register (CANTARQ)
Table 9-13. CANTARQ Register Field Descriptions
Field Description
2:0
ABTRQ[2:0] Abort Request — The CPU sets the ABTRQx bit to request that a scheduled message buffer (TXEx = 0) be
aborted. The MSCAN grants the request if the message has not already started transmission, or if the
transmission is not successful (lost arbitration or error). When a message is aborted, the associated TXE (see
Section 9.3.2.7, “MSCAN Transmitter Flag Register (CANTFLG)”) and abort acknowledge flags (ABTAK, see
Section 9.3.2.10, “MSCAN Transmitter Message Abort Acknowledge Register (CANTAAK)”) are set and a
transmit interrupt occurs if enabled. The CPU cannot reset ABTRQx. ABTRQx is reset whenever the associated
TXE flag is set.
0 No abort request
1 Abort request pending
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 291
9.3.2.10 MSCAN Transmitter Message Abort Acknowledge Register (CANTAAK)
The CANTAAK register indicates the successful abort of a queued message, if requested by the
appropriate bits in the CANTARQ register.
NOTE
The CANTAAK register is held in the reset state when the initialization
mode is active (INITRQ = 1 and INITAK = 1).
Read: Anytime
Write: Unimplemented for ABTAKx flags
Module Base + 0x0009
76543210
R00000ABTAK2 ABTAK1 ABTAK0
W
Reset: 00000000
= Unimplemented
Figure 9-13. MSCAN Transmitter Message Abort Acknowledge Register (CANTAAK)
Table 9-14. CANTAAK Register Field Descriptions
Field Description
2:0
ABTAK[2:0] Abort Acknowledge — This flag acknowledges that a message was aborted due to a pending abort request
from the CPU. After a particular message buffer is flagged empty, this flag can be used by the application
software to identify whether the message was aborted successfully or was sent anyway. The ABTAKx flag is
cleared whenever the corresponding TXE flag is cleared.
0 The message was not aborted.
1 The message was aborted.
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
292 Freescale Semiconductor
9.3.2.11 MSCAN Transmit Buffer Selection Register (CANTBSEL)
The CANTBSEL register allows the selection of the actual transmit message buffer, which then will be
accessible in the CANTXFG register space.
NOTE
The CANTBSEL register is held in the reset state when the initialization
mode is active (INITRQ = 1 and INITAK=1). This register is writable when
not in initialization mode (INITRQ = 0 and INITAK = 0).
Read: Find the lowest ordered bit set to 1, all other bits will be read as 0
Write: Anytime when not in initialization mode
The following gives a short programming example of the usage of the CANTBSEL register:
To get the next available transmit buffer, application software must read the CANTFLG register and write
this value back into the CANTBSEL register. In this example Tx buffers TX1 and TX2 are available. The
value read from CANTFLG is therefore 0b0000_0110. When writing this value back to CANTBSEL, the
Tx buffer TX1 is selected in the CANTXFG because the lowest numbered bit set to 1 is at bit position 1.
Reading back this value out of CANTBSEL results in 0b0000_0010, because only the lowest numbered
bit position set to 1 is presented. This mechanism eases the application software the selection of the next
available Tx buffer.
LDD CANTFLG; value read is 0b0000_0110
STD CANTBSEL; value written is 0b0000_0110
LDD CANTBSEL; value read is 0b0000_0010
If all transmit message buffers are deselected, no accesses are allowed to the CANTXFG registers.
Module Base + 0x000A
76543210
R00000
TX2 TX1 TX0
W
Reset: 00000000
= Unimplemented
Figure 9-14. MSCAN Transmit Buffer Selection Register (CANTBSEL)
Table 9-15. CANTBSEL Register Field Descriptions
Field Description
2:0
TX[2:0] Transmit Buffer Select — The lowest numbered bit places the respective transmit buffer in the CANTXFG
register space (e.g., TX1 = 1 and TX0 = 1 selects transmit buffer TX0; TX1 = 1 and TX0 = 0 selects transmit
buffer TX1). Read and write accesses to the selected transmit buffer will be blocked, if the corresponding TXEx
bit is cleared and the buffer is scheduled for transmission (see Section 9.3.2.7, “MSCAN Transmitter Flag
Register (CANTFLG)”).
0 The associated message buffer is deselected
1 The associated message buffer is selected, if lowest numbered bit
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 293
9.3.2.12 MSCAN Identifier Acceptance Control Register (CANIDAC)
The CANIDAC register is used for identifier acceptance control as described below.
Read: Anytime
Write: Anytime in initialization mode (INITRQ = 1 and INITAK = 1), except bits IDHITx, which are
read-only
Module Base + 0x000B
76543210
R0 0 IDAM1 IDAM0 0 IDHIT2 IDHIT1 IDHIT0
W
Reset: 00000000
= Unimplemented
Figure 9-15. MSCAN Identifier Acceptance Control Register (CANIDAC)
Table 9-16. CANIDAC Register Field Descriptions
Field Description
5:4
IDAM[1:0] Identifier Acceptance Mode The CPU sets these flags to define the identifier acceptance filter organization
(see Section 9.4.3, “Identifier Acceptance Filter”). Table 9-17 summarizes the different settings. In filter closed
mode, no message is accepted such that the foreground buffer is never reloaded.
2:0
IDHIT[2:0] Identifier Acceptance Hit Indicator — The MSCAN sets these flags to indicate an identifier acceptance hit (see
Section 9.4.3, “Identifier Acceptance Filter”). Table 9-18 summarizes the different settings.
Table 9-17. Identifier Acceptance Mode Settings
IDAM1 IDAM0 Identifier Acceptance Mode
0 0 Two 32-bit acceptance filters
0 1 Four 16-bit acceptance filters
1 0 Eight 8-bit acceptance filters
1 1 Filter closed
Table 9-18. Identifier Acceptance Hit Indication
IDHIT2 IDHIT1 IDHIT0 Identifier Acceptance Hit
0 0 0 Filter 0 hit
0 0 1 Filter 1 hit
0 1 0 Filter 2 hit
0 1 1 Filter 3 hit
1 0 0 Filter 4 hit
1 0 1 Filter 5 hit
1 1 0 Filter 6 hit
1 1 1 Filter 7 hit
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
294 Freescale Semiconductor
The IDHITx indicators are always related to the message in the foreground buffer (RxFG). When a
message gets shifted into the foreground buffer of the receiver FIFO the indicators are updated as well.
9.3.2.13 MSCAN Reserved Registers
These registers are reserved for factory testing of the MSCAN module and is not available in normal
system operation modes.
Read: Always read 0x0000 in normal system operation modes
Write: Unimplemented in normal system operation modes
NOTE
Writing to this register when in special modes can alter the MSCAN
functionality.
9.3.2.14 MSCAN Receive Error Counter (CANRXERR)
This register reflects the status of the MSCAN receive error counter.
Read: Only when in sleep mode (SLPRQ = 1 and SLPAK = 1) or initialization mode (INITRQ = 1 and
INITAK = 1)
Write: Unimplemented
Module Base + 0x000C, 0x000D
76543210
R00000000
W
Reset: 00000000
= Unimplemented
Figure 9-16. MSCAN Reserved Registers
Module Base + 0x000E
76543210
R RXERR7 RXERR6 RXERR5 RXERR4 RXERR3 RXERR2 RXERR1 RXERR0
W
Reset: 00000000
= Unimplemented
Figure 9-17. MSCAN Receive Error Counter (CANRXERR)
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 295
NOTE
Reading this register when in any other mode other than sleep or
initialization mode may return an incorrect value. For MCUs with dual
CPUs, this may result in a CPU fault condition.
Writing to this register when in special modes can alter the MSCAN
functionality.
9.3.2.15 MSCAN Transmit Error Counter (CANTXERR)
This register reflects the status of the MSCAN transmit error counter.
Read: Only when in sleep mode (SLPRQ = 1 and SLPAK = 1) or initialization mode (INITRQ = 1 and
INITAK = 1)
Write: Unimplemented
NOTE
Reading this register when in any other mode other than sleep or
initialization mode, may return an incorrect value. For MCUs with dual
CPUs, this may result in a CPU fault condition.
Writing to this register when in special modes can alter the MSCAN
functionality.
Module Base + 0x000F
76543210
R TXERR7 TXERR6 TXERR5 TXERR4 TXERR3 TXERR2 TXERR1 TXERR0
W
Reset: 00000000
= Unimplemented
Figure 9-18. MSCAN Transmit Error Counter (CANTXERR)
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
296 Freescale Semiconductor
9.3.2.16 MSCAN Identifier Acceptance Registers (CANIDAR0-7)
On reception, each message is written into the background receive buffer. The CPU is only signalled to
read the message if it passes the criteria in the identifier acceptance and identifier mask registers
(accepted); otherwise, the message is overwritten by the next message (dropped).
The acceptance registers of the MSCAN are applied on the IDR0–IDR3 registers (see Section 9.3.3.1,
“Identifier Registers (IDR0–IDR3)”) of incoming messages in a bit by bit manner (see Section 9.4.3,
“Identifier Acceptance Filter”).
For extended identifiers, all four acceptance and mask registers are applied. For standard identifiers, only
the first two (CANIDAR0/1, CANIDMR0/1) are applied.
Read: Anytime
Write: Anytime in initialization mode (INITRQ = 1 and INITAK = 1)
Module Base + 0x0010 (CANIDAR0)
0x0011 (CANIDAR1)
0x0012 (CANIDAR2)
0x0013 (CANIDAR3)
76543210
RAC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0
W
Reset 00000000
76543210
RAC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0
W
Reset 00000000
76543210
RAC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0
W
Reset 00000000
76543210
RAC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0
W
Reset 00000000
Figure 9-19. MSCAN Identifier Acceptance Registers (First Bank) — CANIDAR0–CANIDAR3
Table 9-19. CANIDAR0–CANIDAR3 Register Field Descriptions
Field Description
7:0
AC[7:0] Acceptance Code Bits AC[7:0] comprise a user-defined sequence of bits with which the corresponding bits
ofthe related identifier register (IDRn)ofthe receivemessage bufferare compared. The result of thiscomparison
is then masked with the corresponding identifier mask register.
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 297
Read: Anytime
Write: Anytime in initialization mode (INITRQ = 1 and INITAK = 1)
Module Base + 0x0018 (CANIDAR4)
0x0019 (CANIDAR5)
0x001A (CANIDAR6)
0x001B (CANIDAR7)
76543210
RAC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0
W
Reset 00000000
76543210
RAC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0
W
Reset 00000000
76543210
RAC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0
W
Reset 00000000
76543210
RAC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0
W
Reset 00000000
Figure 9-20. MSCAN Identifier Acceptance Registers (Second Bank) — CANIDAR4–CANIDAR7
Table 9-20. CANIDAR4–CANIDAR7 Register Field Descriptions
Field Description
7:0
AC[7:0] Acceptance Code Bits AC[7:0] comprise a user-defined sequence of bits with which the corresponding bits
ofthe related identifier register (IDRn)ofthe receivemessage bufferare compared. The result of thiscomparison
is then masked with the corresponding identifier mask register.
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
298 Freescale Semiconductor
9.3.2.17 MSCAN Identifier Mask Registers (CANIDMR0–CANIDMR7)
The identifier mask register specifies which of the corresponding bits in the identifier acceptance register
are relevant for acceptance filtering. To receive standard identifiers in 32 bit filter mode, it is required to
program the last three bits (AM[2:0]) in the mask registers CANIDMR1 and CANIDMR5 to “don’t care.
To receive standard identifiers in 16 bit filter mode, it is required to program the last three bits (AM[2:0])
in the mask registers CANIDMR1, CANIDMR3, CANIDMR5, and CANIDMR7 to “don’t care.
Read: Anytime
Write: Anytime in initialization mode (INITRQ = 1 and INITAK = 1)
Module Base + 0x0014 (CANIDMR0)
0x0015 (CANIDMR1)
0x0016 (CANIDMR2)
0x0017 (CANIDMR3)
76543210
RAM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0
W
Reset 00000000
76543210
RAM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0
W
Reset 00000000
76543210
RAM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0
W
Reset 00000000
76543210
RAM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0
W
Reset 00000000
Figure 9-21. MSCAN Identifier Mask Registers (First Bank) — CANIDMR0–CANIDMR3
Table 9-21. CANIDMR0–CANIDMR3 Register Field Descriptions
Field Description
7:0
AM[7:0] Acceptance Mask Bits If a particular bit in this register is cleared, this indicates that the corresponding bit in
the identifier acceptance register must be the same as its identifier bit before a match is detected. The message
is accepted if all such bits match. If a bit is set, it indicates that the state of the corresponding bit in the identifier
acceptance register does not affect whether or not the message is accepted.
0 Match corresponding acceptance code register and identifier bits
1 Ignore corresponding acceptance code register bit
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 299
Read: Anytime
Write: Anytime in initialization mode (INITRQ = 1 and INITAK = 1)
Module Base + 0x001C (CANIDMR4)
0x001D (CANIDMR5)
0x001E (CANIDMR6)
0x001F (CANIDMR7)
76543210
RAM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0
W
Reset 00000000
76543210
RAM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0
W
Reset 00000000
76543210
RAM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0
W
Reset 00000000
76543210
RAM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0
W
Reset 00000000
Figure 9-22. MSCAN Identifier Mask Registers (Second Bank) — CANIDMR4–CANIDMR7
Table 9-22. CANIDMR4–CANIDMR7 Register Field Descriptions
Field Description
7:0
AM[7:0] Acceptance Mask Bits If a particular bit in this register is cleared, this indicates that the corresponding bit in
the identifier acceptance register must be the same as its identifier bit before a match is detected. The message
is accepted if all such bits match. If a bit is set, it indicates that the state of the corresponding bit in the identifier
acceptance register does not affect whether or not the message is accepted.
0 Match corresponding acceptance code register and identifier bits
1 Ignore corresponding acceptance code register bit
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
300 Freescale Semiconductor
9.3.3 Programmer’s Model of Message Storage
The following section details the organization of the receive and transmit message buffers and the
associated control registers.
To simplify the programmer interface, the receive and transmit message buffers have the same outline.
Each message buffer allocates 16 bytes in the memory map containing a 13 byte data structure.
An additional transmit buffer priority register (TBPR) is defined for the transmit buffers. Within the last
two bytes of this memory map, the MSCAN stores a special 16-bit time stamp, which is sampled from an
internal timer after successful transmission or reception of a message. This feature is only available for
transmit and receiver buffers, if the TIME bit is set (see Section 9.3.2.1, “MSCAN Control Register 0
(CANCTL0)”).
The time stamp register is written by the MSCAN. The CPU can only read these registers.
Figure 9-23 shows the common 13-byte data structure of receive and transmit buffers for extended
identifiers. The mapping of standard identifiers into the IDR registers is shown in Figure 9-24.
All bits of the receive and transmit buffers are ‘x’ out of reset because of RAM-based implementation1.
All reserved or unused bits of the receive and transmit buffers always read ‘x’.
Table 9-23. Message Buffer Organization
Offset
Address Register Access
0x00X0 Identifier Register 0
0x00X1 Identifier Register 1
0x00X2 Identifier Register 2
0x00X3 Identifier Register 3
0x00X4 Data Segment Register 0
0x00X5 Data Segment Register 1
0x00X6 Data Segment Register 2
0x00X7 Data Segment Register 3
0x00X8 Data Segment Register 4
0x00X9 Data Segment Register 5
0x00XA Data Segment Register 6
0x00XB Data Segment Register 7
0x00XC Data Length Register
0x00XD Transmit Buffer Priority Register1
1Not applicable for receive buffers
0x00XE Time Stamp Register (High Byte)2
2Read-only for CPU
0x00XF Time Stamp Register (Low Byte)3
3Read-only for CPU
1. Exception: The transmit priority registers are 0 out of reset.
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 301
Read: For transmit buffers, anytime when TXEx flag is set (see Section 9.3.2.7, “MSCAN Transmitter
Flag Register (CANTFLG)”) and the corresponding transmit buffer is selected in CANTBSEL (see
Section 9.3.2.11, “MSCAN Transmit Buffer Selection Register (CANTBSEL)”). For receive buffers, only
when RXF flag is set (see Section 9.3.2.5, “MSCAN Receiver Flag Register (CANRFLG)”).
Register
Name Bit 7 654321Bit0
0x00X0
IDR0 RID28 ID27 ID26 ID25 ID24 ID23 ID22 ID21
W
0x00X1
IDR1 RID20 ID19 ID18 SRR (=1) IDE (=1) ID17 ID16 ID15
W
0x00X2
IDR2 RID14 ID13 ID12 ID11 ID10 ID9 ID8 ID7
W
0x00X3
IDR3 RID6 ID5 ID4 ID3 ID2 ID1 ID0 RTR
W
0x00X4
DSR0 RDB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
W
0x00X5
DSR1 RDB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
W
0x00X6
DSR2 RDB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
W
0x00X7
DSR3 RDB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
W
0x00X8
DSR4 RDB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
W
0x00X9
DSR5 RDB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
W
0x00XA
DSR6 RDB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
W
0x00XB
DSR7 RDB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
W
0x00XC
DLR RDLC3 DLC2 DLC1 DLC0
W
= Unused, always read ‘x’
Figure 9-23. Receive/Transmit Message Buffer — Extended Identifier Mapping
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
302 Freescale Semiconductor
Write: For transmit buffers, anytime when TXEx flag is set (see Section 9.3.2.7, “MSCAN Transmitter
Flag Register (CANTFLG)”) and the corresponding transmit buffer is selected in CANTBSEL (see
Section 9.3.2.11, “MSCAN Transmit Buffer Selection Register (CANTBSEL)”). Unimplemented for
receive buffers.
Reset: Undefined (0x00XX) because of RAM-based implementation
9.3.3.1 Identifier Registers (IDR0–IDR3)
The identifier registers for an extended format identifier consist of a total of 32 bits; ID[28:0], SRR, IDE,
and RTR bits. The identifier registers for a standard format identifier consist of a total of 13 bits; ID[10:0],
RTR, and IDE bits.
9.3.3.1.1 IDR0–IDR3 for Extended Identifier Mapping
Register
Name Bit 7 654321Bit 0
IDR0
0x00X0 RID10 ID9 ID8 ID7 ID6 ID5 ID4 ID3
W
IDR1
0x00X1 RID2 ID1 ID0 RTR IDE (=0)
W
IDR2
0x00X2 R
W
IDR3
0x00X3 R
W
= Unused, always read ‘x’
Figure 9-24. Receive/Transmit Message Buffer — Standard Identifier Mapping
Module Base + 0x00X1
76543210
RID28 ID27 ID26 ID25 ID24 ID23 ID22 ID21
W
Reset: xxxxxxxx
Figure 9-25. Identifier Register 0 (IDR0) — Extended Identifier Mapping
Table 9-24. IDR0 Register Field Descriptions — Extended
Field Description
7:0
ID[28:21] Extended Format Identifier — The identifiers consist of 29 bits (ID[28:0]) for the extended format. ID28 is the
most significant bit and is transmitted first on the CAN bus during the arbitration procedure. The priority of an
identifier is defined to be highest for the smallest binary number.
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 303
Module Base + 0x00X1
76543210
RID20 ID19 ID18 SRR (=1) IDE (=1) ID17 ID16 ID15
W
Reset: xxxxxxxx
Figure 9-26. Identifier Register 1 (IDR1) — Extended Identifier Mapping
Table 9-25. IDR1 Register Field Descriptions — Extended
Field Description
7:5
ID[20:18] Extended Format Identifier — The identifiers consist of 29 bits (ID[28:0]) for the extended format. ID28 is the
most significant bit and is transmitted first on the CAN bus during the arbitration procedure. The priority of an
identifier is defined to be highest for the smallest binary number.
4
SRR Substitute Remote Request — This fixed recessive bit is used only in extended format. It must be set to 1 by
the user for transmission buffers and is stored as received on the CAN bus for receive buffers.
3
IDE ID Extended This flag indicates whether the extended or standard identifier format is applied in this buffer. In
the case of a receive buffer, the flag is set as received and indicates to the CPU how to process the buffer
identifier registers. In the case of a transmit buffer, the flag indicates to the MSCAN what type of identifier to send.
0 Standard format (11 bit)
1 Extended format (29 bit)
2:0
ID[17:15] Extended Format Identifier — The identifiers consist of 29 bits (ID[28:0]) for the extended format. ID28 is the
most significant bit and is transmitted first on the CAN bus during the arbitration procedure. The priority of an
identifier is defined to be highest for the smallest binary number.
Module Base + 0x00X2
76543210
RID14 ID13 ID12 ID11 ID10 ID9 ID8 ID7
W
Reset: xxxxxxxx
Figure 9-27. Identifier Register 2 (IDR2) — Extended Identifier Mapping
Table 9-26. IDR2 Register Field Descriptions — Extended
Field Description
7:0
ID[14:7] Extended Format Identifier — The identifiers consist of 29 bits (ID[28:0]) for the extended format. ID28 is the
most significant bit and is transmitted first on the CAN bus during the arbitration procedure. The priority of an
identifier is defined to be highest for the smallest binary number.
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
304 Freescale Semiconductor
9.3.3.1.2 IDR0–IDR3 for Standard Identifier Mapping
Module Base + 0x00X3
76543210
RID6 ID5 ID4 ID3 ID2 ID1 ID0 RTR
W
Reset: xxxxxxxx
Figure 9-28. Identifier Register 3 (IDR3) — Extended Identifier Mapping
Table 9-27. IDR3 Register Field Descriptions — Extended
Field Description
7:1
ID[6:0] Extended Format Identifier — The identifiers consist of 29 bits (ID[28:0]) for the extended format. ID28 is the
most significant bit and is transmitted first on the CAN bus during the arbitration procedure. The priority of an
identifier is defined to be highest for the smallest binary number.
0
RTR Remote Transmission Request — This flag reflects the status of the remote transmission request bit in the
CAN frame. In the case of a receive buffer, it indicates the status of the received frame and supports the
transmission of an answering frame in software. In the case of a transmit buffer, this flag defines the setting of
the RTR bit to be sent.
0 Data frame
1 Remote frame
Module Base + 0x00X0
76543210
RID10 ID9 ID8 ID7 ID6 ID5 ID4 ID3
W
Reset: xxxxxxxx
Figure 9-29. Identifier Register 0 — Standard Mapping
Table 9-28. IDR0 Register Field Descriptions — Standard
Field Description
7:0
ID[10:3] Standard Format Identifier — The identifiers consist of 11 bits (ID[10:0]) for the standard format. ID10 is the
most significant bit and is transmitted first on the CAN bus during the arbitration procedure. The priority of an
identifier is defined to be highest for the smallest binary number. See also ID bits in Table 9-29.
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 305
Module Base + 0x00X1
76543210
RID2 ID1 ID0 RTR IDE (=0)
W
Reset: xxxxxxxx
= Unused; always read ‘x’
Figure 9-30. Identifier Register 1 — Standard Mapping
Table 9-29. IDR1 Register Field Descriptions
Field Description
7:5
ID[2:0] Standard Format Identifier — The identifiers consist of 11 bits (ID[10:0]) for the standard format. ID10 is the
most significant bit and is transmitted first on the CAN bus during the arbitration procedure. The priority of an
identifier is defined to be highest for the smallest binary number. See also ID bits in Table 9-28.
4
RTR Remote Transmission Request This flag reflects the status of the Remote Transmission Request bit in the
CAN frame. In the case of a receive buffer, it indicates the status of the received frame and supports the
transmission of an answering frame in software. In the case of a transmit buffer, this flag defines the setting of
the RTR bit to be sent.
0 Data frame
1 Remote frame
3
IDE ID Extended This flag indicates whether the extended or standard identifier format is applied in this buffer. In
the case of a receive buffer, the flag is set as received and indicates to the CPU how to process the buffer
identifier registers. In the case of a transmit buffer, the flag indicates to the MSCAN what type of identifier to send.
0 Standard format (11 bit)
1 Extended format (29 bit)
Module Base + 0x00X2
76543210
R
W
Reset: xxxxxxxx
= Unused; always read ‘x’
Figure 9-31. Identifier Register 2 — Standard Mapping
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
306 Freescale Semiconductor
9.3.3.2 Data Segment Registers (DSR0-7)
The eight data segment registers, each with bits DB[7:0], contain the data to be transmitted or received.
The number of bytes to be transmitted or received is determined by the data length code in the
corresponding DLR register.
Module Base + 0x00X3
76543210
R
W
Reset: xxxxxxxx
= Unused; always read ‘x’
Figure 9-32. Identifier Register 3 — Standard Mapping
Module Base + 0x0004 (DSR0)
0x0005 (DSR1)
0x0006 (DSR2)
0x0007 (DSR3)
0x0008 (DSR4)
0x0009 (DSR5)
0x000A (DSR6)
0x000B (DSR7)
76543210
RDB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
W
Reset: xxxxxxxx
Figure 9-33. Data Segment Registers (DSR0–DSR7) — Extended Identifier Mapping
Table 9-30. DSR0–DSR7 Register Field Descriptions
Field Description
7:0
DB[7:0] Data bits 7:0
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 307
9.3.3.3 Data Length Register (DLR)
This register keeps the data length field of the CAN frame.
9.3.3.4 Transmit Buffer Priority Register (TBPR)
This register defines the local priority of the associated message buffer. The local priority is used for the
internal prioritization process of the MSCAN and is defined to be highest for the smallest binary number.
The MSCAN implements the following internal prioritization mechanisms:
All transmission buffers with a cleared TXEx flag participate in the prioritization immediately
before the SOF (start of frame) is sent.
The transmission buffer with the lowest local priority field wins the prioritization.
Module Base + 0x00XB
76543210
RDLC3 DLC2 DLC1 DLC0
W
Reset: xxxxxxxx
= Unused; always read “x”
Figure 9-34. Data Length Register (DLR) — Extended Identifier Mapping
Table 9-31. DLR Register Field Descriptions
Field Description
3:0
DLC[3:0] Data Length Code Bits The data length code contains thenumber of bytes(data bytecount) ofthe respective
message. During the transmission of a remote frame, the data length code is transmitted as programmed while
the number of transmitted data bytes is always 0. The data byte count ranges from 0 to 8 for a data frame.
Table 9-32 shows the effect of setting the DLC bits.
Table 9-32. Data Length Codes
Data Length Code Data Byte
Count
DLC3 DLC2 DLC1 DLC0
00000
00011
00102
00113
01004
01015
01106
01117
10008
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
308 Freescale Semiconductor
In cases of more than one buffer having the same lowest priority, the message buffer with the lower index
number wins.
Read: Anytime when TXEx flag is set (see Section 9.3.2.7, “MSCAN Transmitter Flag Register
(CANTFLG)”) and the corresponding transmit buffer is selected in CANTBSEL (see Section 9.3.2.11,
“MSCAN Transmit Buffer Selection Register (CANTBSEL)”).
Write: Anytime when TXEx flag is set (see Section 9.3.2.7, “MSCAN Transmitter Flag Register
(CANTFLG)”) and the corresponding transmit buffer is selected in CANTBSEL (see Section 9.3.2.11,
“MSCAN Transmit Buffer Selection Register (CANTBSEL)”).
9.3.3.5 Time Stamp Register (TSRH–TSRL)
If the TIME bit is enabled, the MSCAN will write a time stamp to the respective registers in the active
transmit or receive buffer right after the EOF of a valid message on the CAN bus (see Section 9.3.2.1,
“MSCAN Control Register 0 (CANCTL0)”). In case of a transmission, the CPU can only read the time
stamp after the respective transmit buffer has been flagged empty.
The timer value, which is used for stamping, is taken from a free running internal CAN bit clock. A timer
overrun is not indicated by the MSCAN. The timer is reset (all bits set to 0) during initialization mode. The
CPU can only read the time stamp registers.
Module Base + 0xXXXD
76543210
RPRIO7 PRIO6 PRIO5 PRIO4 PRIO3 PRIO2 PRIO1 PRIO0
W
Reset: 00000000
Figure 9-35. Transmit Buffer Priority Register (TBPR)
Module Base + 0xXXXE
76543210
R TSR15 TSR14 TSR13 TSR12 TSR11 TSR10 TSR9 TSR8
W
Reset: xxxxxxxx
Figure 9-36. Time Stamp Register — High Byte (TSRH)
Module Base + 0xXXXF
76543210
R TSR7 TSR6 TSR5 TSR4 TSR3 TSR2 TSR1 TSR0
W
Reset: xxxxxxxx
Figure 9-37. Time Stamp Register — Low Byte (TSRL)
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 309
Read: Anytime when TXEx flag is set (see Section 9.3.2.7, “MSCAN Transmitter Flag Register
(CANTFLG)”) and the corresponding transmit buffer is selected in CANTBSEL (see Section 9.3.2.11,
“MSCAN Transmit Buffer Selection Register (CANTBSEL)”).
Write: Unimplemented
9.4 Functional Description
9.4.1 General
This section provides a complete functional description of the MSCAN. It describes each of the features
and modes listed in the introduction.
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
310 Freescale Semiconductor
9.4.2 Message Storage
Figure 9-38. User Model for Message Buffer Organization
MSCAN facilitates a sophisticated message storage system which addresses the requirements of a broad
range of network applications.
MSCAN
Rx0
Rx1
CAN
Receive / Transmit
Engine
CPU12
Memory Mapped
I/O
CPU bus
MSCAN
Tx2
TXE2
PRIO
Receiver
Transmitter
RxBG
TxBG
Tx0
TXE0
PRIO
TxBG
Tx1
PRIO
TXE1
TxFG
CPU bus
Rx2
Rx3
Rx4
RXF
RxFG
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 311
9.4.2.1 Message Transmit Background
Modern application layer software is built upon two fundamental assumptions:
Any CAN node is able to send out a stream of scheduled messages without releasing the CAN bus
between the two messages. Such nodes arbitrate for the CAN bus immediately after sending the
previous message and only release the CAN bus in case of lost arbitration.
The internal message queue within any CAN node is organized such that the highest priority
message is sent out first, if more than one message is ready to be sent.
The behavior described in the bullets above cannot be achieved with a single transmit buffer. That buffer
must be reloaded immediately after the previous message is sent. This loading process lasts a finite amount
of time and must be completed within the inter-frame sequence (IFS) to be able to send an uninterrupted
stream of messages. Even if this is feasible for limited CAN bus speeds, it requires that the CPU reacts
with short latencies to the transmit interrupt.
A double buffer scheme de-couples the reloading of the transmit buffer from the actual message sending
and, therefore, reduces the reactiveness requirements of the CPU. Problems can arise if the sending of a
message is finished while the CPU re-loads the second buffer. No buffer would then be ready for
transmission, and the CAN bus would be released.
At least three transmit buffers are required to meet the first of the above requirements under all
circumstances. The MSCAN has three transmit buffers.
The second requirement calls for some sort of internal prioritization which the MSCAN implements with
the “local priority” concept described in Section 9.4.2.2, “Transmit Structures.”
9.4.2.2 Transmit Structures
The MSCAN triple transmit buffer scheme optimizes real-time performance by allowing multiple
messages to be set up in advance. The three buffers are arranged as shown in Figure 9-38.
All three buffers have a 13-byte data structure similar to the outline of the receive buffers (see
Section 9.3.3, “Programmer’s Model of Message Storage”). An additional Section 9.3.3.4, “Transmit
Buffer Priority Register (TBPR) contains an 8-bit local priority field (PRIO) (see Section 9.3.3.4,
“Transmit Buffer Priority Register (TBPR)”). The remaining two bytes are used for time stamping of a
message, if required (see Section 9.3.3.5, “Time Stamp Register (TSRH–TSRL)”).
To transmit a message, the CPU must identify an available transmit buffer, which is indicated by a set
transmitter buffer empty (TXEx) flag (see Section 9.3.2.7, “MSCAN Transmitter Flag Register
(CANTFLG)”). If a transmit buffer is available, the CPU must set a pointer to this buffer by writing to the
CANTBSEL register (see Section 9.3.2.11, “MSCAN Transmit Buffer Selection Register
(CANTBSEL)”). This makes the respective buffer accessible within the CANTXFG address space (see
Section 9.3.3, “Programmer’s Model of Message Storage”). The algorithmic feature associated with the
CANTBSEL register simplifies the transmit buffer selection. In addition, this scheme makes the handler
software simpler because only one address area is applicable for the transmit process, and the required
address space is minimized.
The CPU then stores the identifier, the control bits, and the data content into one of the transmit buffers.
Finally, the buffer is flagged as ready for transmission by clearing the associated TXE flag.
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
312 Freescale Semiconductor
The MSCAN then schedules the message for transmission and signals the successful transmission of the
buffer by setting the associated TXE flag. A transmit interrupt (see Section 9.4.7.2, “Transmit Interrupt”)
is generated1 when TXEx is set and can be used to drive the application software to re-load the buffer.
If more than one buffer is scheduled for transmission when the CAN bus becomes available for arbitration,
the MSCAN uses the local priority setting of the three buffers to determine the prioritization. For this
purpose, every transmit buffer has an 8-bit local priority field (PRIO). The application software programs
this field when the message is set up. The local priority reflects the priority of this particular message
relative to the set of messages being transmitted from this node. The lowest binary value of the PRIO field
is defined to be the highest priority. The internal scheduling process takes place whenever the MSCAN
arbitrates for the CAN bus. This is also the case after the occurrence of a transmission error.
When a high priority message is scheduled by the application software, it may become necessary to abort
a lower priority message in one of the three transmit buffers. Because messages that are already in
transmission cannot be aborted, the user must request the abort by setting the corresponding abort request
bit (ABTRQ) (see Section 9.3.2.9, “MSCAN Transmitter Message Abort Request Register
(CANTARQ)”.) The MSCAN then grants the request, if possible, by:
1. Setting the corresponding abort acknowledge flag (ABTAK) in the CANTAAK register.
2. Setting the associated TXE flag to release the buffer.
3. Generating a transmit interrupt. The transmit interrupt handler software can determine from the
setting of the ABTAK flag whether the message was aborted (ABTAK = 1) or sent (ABTAK = 0).
9.4.2.3 Receive Structures
The received messages are stored in a five stage input FIFO. The five message buffers are alternately
mappedinto a singlememoryarea (see Figure 9-38).The background receivebuffer (RxBG) isexclusively
associated with the MSCAN, but the foreground receive buffer (RxFG) is addressable by the CPU (see
Figure 9-38). This scheme simplifies the handler software because only one address area is applicable for
the receive process.
All receive buffers have a size of 15 bytes to store the CAN control bits, the identifier (standard or
extended), the data contents, and a time stamp, if enabled (see Section 9.3.3, “Programmer’s Model of
Message Storage”).
The receiver full flag (RXF) (see Section 9.3.2.5, “MSCAN Receiver Flag Register (CANRFLG)”) signals
the status of the foreground receive buffer. When the buffer contains a correctly received message with a
matching identifier, this flag is set.
On reception, each message is checked to see whether it passes the filter (see Section 9.4.3, “Identifier
Acceptance Filter”) and simultaneously is written into the active RxBG. After successful reception of a
valid message, the MSCAN shifts the content of RxBG into the receiver FIFO2, sets the RXF flag, and
generates a receive interrupt (see Section 9.4.7.3, “Receive Interrupt”) to the CPU3. The user’s receive
handler must read the received message from the RxFG and then reset the RXF flag to acknowledge the
interrupt and to release the foreground buffer. A new message, which can follow immediately after the IFS
1. The transmit interrupt occurs only if not masked. A polling scheme can be applied on TXEx also.
2. Only if the RXF flag is not set.
3. The receive interrupt occurs only if not masked. A polling scheme can be applied on RXF also.
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 313
field of the CAN frame, is received into the next available RxBG. If the MSCAN receives an invalid
message in its RxBG (wrong identifier, transmission errors, etc.) the actual contents of the buffer will be
over-written by the next message. The buffer will then not be shifted into the FIFO.
When the MSCAN module is transmitting, the MSCAN receives its own transmitted messages into the
background receive buffer, RxBG, but does not shift it into the receiver FIFO, generate a receive interrupt,
or acknowledge its own messages on the CAN bus. The exception to this rule is in loopback mode (see
Section 9.3.2.2, “MSCAN Control Register 1 (CANCTL1)”) where the MSCAN treats its own messages
exactly like all other incoming messages. The MSCAN receives its own transmitted messages in the event
that it loses arbitration. If arbitration is lost, the MSCAN must be prepared to become a receiver.
An overrun condition occurs when all receive message buffers in the FIFO are filled with correctly
received messages with accepted identifiers and another message is correctly received from the CAN bus
with an accepted identifier. The latter message is discarded and an error interrupt with overrun indication
is generated if enabled (see Section 9.4.7.5, “Error Interrupt”). The MSCAN remains able to transmit
messages while the receiver FIFO being filled, but all incoming messages are discarded. As soon as a
receive buffer in the FIFO is available again, new valid messages will be accepted.
9.4.3 Identifier Acceptance Filter
The MSCAN identifier acceptance registers (see Section 9.3.2.12, “MSCAN Identifier Acceptance
Control Register (CANIDAC)”) define the acceptable patterns of the standard or extended identifier
(ID[10:0] or ID[28:0]). Any of these bits can be marked ‘don’t care’ in the MSCAN identifier mask
registers (see Section 9.3.2.17, “MSCAN Identifier Mask Registers (CANIDMR0–CANIDMR7)”).
A filter hit is indicated to the application software by a set receive buffer full flag (RXF = 1) and three bits
in the CANIDAC register (see Section 9.3.2.12, “MSCAN Identifier Acceptance Control Register
(CANIDAC)”). These identifier hit flags (IDHIT[2:0]) clearly identify the filter section that caused the
acceptance. They simplify the application software’s task to identify the cause of the receiver interrupt. If
more than one hit occurs (two or more filters match), the lower hit has priority.
A very flexible programmable generic identifier acceptance filter has been introduced to reduce the CPU
interrupt loading. The filter is programmable to operate in four different modes (see Bosch CAN 2.0A/B
protocol specification):
Two identifier acceptance filters, each to be applied to:
The full 29 bits of the extended identifier and to the following bits of the CAN 2.0B frame:
Remote transmission request (RTR)
Identifier extension (IDE)
Substitute remote request (SRR)
The 11 bits of the standard identifier plus the RTR and IDE bits of the CAN 2.0A/B messages1.
This mode implements two filters for a full length CAN 2.0B compliant extended identifier.
Figure 9-39 shows how the first 32-bit filter bank (CANIDAR0–CANIDAR3,
CANIDMR0–CANIDMR3) produces a filter 0 hit. Similarly, the second filter bank
(CANIDAR4–CANIDAR7, CANIDMR4–CANIDMR7) produces a filter 1 hit.
1.Although this mode can be used for standard identifiers, it is recommended to use the four or eight identifier acceptance
filters for standard identifiers
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
314 Freescale Semiconductor
Four identifier acceptance filters, each to be applied to
a) the 14 most significant bits of the extended identifier plus the SRR and IDE bits of CAN 2.0B
messages or
b) the 11 bits of the standard identifier, the RTR and IDE bits of CAN 2.0A/B messages.
Figure 9-40 shows how the first 32-bit filter bank (CANIDAR0–CANIDA3,
CANIDMR0–3CANIDMR) produces filter 0 and 1 hits. Similarly, the second filter bank
(CANIDAR4–CANIDAR7, CANIDMR4–CANIDMR7) produces filter 2 and 3 hits.
Eight identifier acceptance filters, each to be applied to the first 8 bits of the identifier. This mode
implements eight independent filters for the first 8 bits of a CAN 2.0A/B compliant standard
identifierora CAN 2.0B compliant extendedidentifier. Figure 9-41 showshowthefirst 32-bit filter
bank(CANIDAR0–CANIDAR3,CANIDMR0–CANIDMR3) produces filter0to 3 hits.Similarly,
the second filter bank (CANIDAR4–CANIDAR7, CANIDMR4–CANIDMR7) produces filter 4 to
7 hits.
Closed filter. No CAN message is copied into the foreground buffer RxFG, and the RXF flag is
never set.
Figure 9-39. 32-bit Maskable Identifier Acceptance Filter
ID28 ID21IDR0
ID10 ID3IDR0
ID20 ID15IDR1
ID2 IDEIDR1
ID14 ID7IDR2
ID10 ID3IDR2
ID6 RTRIDR3
ID10 ID3IDR3
AC7 AC0CANIDAR0
AM7 AM0CANIDMR0
AC7 AC0CANIDAR1
AM7 AM0CANIDMR1
AC7 AC0CANIDAR2
AM7 AM0CANIDMR2
AC7 AC0CANIDAR3
AM7 AM0CANIDMR3
ID Accepted (Filter 0 Hit)
CAN 2.0B
Extended Identifier
CAN 2.0A/B
Standard Identifier
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 315
Figure 9-40. 16-bit Maskable Identifier Acceptance Filters
ID28 ID21IDR0
ID10 ID3IDR0
ID20 ID15IDR1
ID2 IDEIDR1
ID14 ID7IDR2
ID10 ID3IDR2
ID6 RTRIDR3
ID10 ID3IDR3
AC7 AC0CANIDAR0
AM7 AM0CANIDMR0
AC7 AC0CANIDAR1
AM7 AM0CANIDMR1
ID Accepted (Filter 0 Hit)
AC7 AC0CANIDAR2
AM7 AM0CANIDMR2
AC7 AC0CANIDAR3
AM7 AM0CANIDMR3
ID Accepted (Filter 1 Hit)
CAN 2.0B
Extended Identifier
CAN 2.0A/B
Standard Identifier
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
316 Freescale Semiconductor
Figure 9-41. 8-bit Maskable Identifier Acceptance Filters
CAN 2.0B
Extended Identifier
CAN 2.0A/B
Standard Identifier
AC7 AC0CIDAR3
AM7 AM0CIDMR3
ID Accepted (Filter 3 Hit)
AC7 AC0CIDAR2
AM7 AM0CIDMR2
ID Accepted (Filter 2 Hit)
AC7 AC0CIDAR1
AM7 AM0CIDMR1
ID Accepted (Filter 1 Hit)
ID28 ID21IDR0
ID10 ID3IDR0
ID20 ID15IDR1
ID2 IDEIDR1
ID14 ID7IDR2
ID10 ID3IDR2
ID6 RTRIDR3
ID10 ID3IDR3
AC7 AC0CIDAR0
AM7 AM0CIDMR0
ID Accepted (Filter 0 Hit)
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 317
9.4.3.1 Protocol Violation Protection
The MSCAN protects the user from accidentally violating the CAN protocol through programming errors.
The protection logic implements the following features:
The receive and transmit error counters cannot be written or otherwise manipulated.
All registers which control the configuration of the MSCAN cannot be modifiedwhile the MSCAN
is on-line. The MSCAN has to be in Initialization Mode. The corresponding INITRQ/INITAK
handshake bits in the CANCTL0/CANCTL1 registers (see Section 9.3.2.1, “MSCAN Control
Register 0 (CANCTL0)”) serve as a lock to protect the following registers:
MSCAN control 1 register (CANCTL1)
MSCAN bus timing registers 0 and 1 (CANBTR0, CANBTR1)
MSCAN identifier acceptance control register (CANIDAC)
MSCAN identifier acceptance registers (CANIDAR0–CANIDAR7)
MSCAN identifier mask registers (CANIDMR0–CANIDMR7)
The TXCAN pin is immediately forced to a recessive state when the MSCAN goes into the power
down mode or initialization mode (see Section 9.4.5.6, “MSCAN Power Down Mode,” and
Section 9.4.5.5, “MSCAN Initialization Mode”).
The MSCAN enable bit (CANE) is writable only once in normal system operation modes, which
provides further protection against inadvertently disabling the MSCAN.
9.4.3.2 Clock System
Figure 9-42 shows the structure of the MSCAN clock generation circuitry.
Figure 9-42. MSCAN Clocking Scheme
The clock source bit (CLKSRC) in the CANCTL1 register (9.3.2.2/9-280) defines whether the internal
CANCLK is connected to the output of a crystal oscillator (oscillator clock) or to the bus clock.
The clock source has to be chosen such that the tight oscillator tolerance requirements (up to 0.4%) of the
CAN protocol are met. Additionally, for high CAN bus rates (1 Mbps), a 45% to 55% duty cycle of the
clock is required.
Bus Clock
Oscillator Clock
MSCAN
CANCLK
CLKSRC
CLKSRC
Prescaler
(1 .. 64)
Time quanta clock (Tq)
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
318 Freescale Semiconductor
If the bus clock is generated from a PLL, it is recommended to select the oscillator clock rather than the
bus clock due to jitter considerations, especially at the faster CAN bus rates.
For microcontrollers without a clock and reset generator (CRG), CANCLK is driven from the crystal
oscillator (oscillator clock).
A programmable prescaler generates the time quanta (Tq) clock from CANCLK. A time quantum is the
atomic unit of time handled by the MSCAN.
Eqn. 9-2
A bit time is subdivided into three segments as described in the Bosch CAN specification. (see
Figure 9-43):
SYNC_SEG: This segment has a fixed length of one time quantum. Signal edges are expected to
happen within this section.
Time Segment 1: This segment includes the PROP_SEG and the PHASE_SEG1 of the CAN
standard. It can be programmed by setting the parameter TSEG1 to consist of 4 to 16 time quanta.
Time Segment 2: This segment represents the PHASE_SEG2 of the CAN standard. It can be
programmed by setting the TSEG2 parameter to be 2 to 8 time quanta long.
Eqn. 9-3
Figure 9-43. Segments within the Bit Time
Tq fCANCLK
Prescaler value(
)
----------------------------------------------------
--
=
Bit Rate fTq
number of Time Quanta()
---------------------------------------------------------------------------------=
SYNC_SEG Time Segment 1 Time Segment 2
1 4 ... 16 2 ... 8
8 ... 25 Time Quanta
= 1 Bit Time
NRZ Signal
Sample Point
(single or triple sampling)
(PROP_SEG + PHASE_SEG1) (PHASE_SEG2)
Transmit Point
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 319
The synchronization jump width (see the Bosch CAN specification for details) can be programmed in a
range of 1 to 4 time quanta by setting the SJW parameter.
The SYNC_SEG, TSEG1, TSEG2, and SJW parameters are set by programming the MSCAN bus timing
registers (CANBTR0, CANBTR1) (see Section 9.3.2.3, “MSCAN Bus Timing Register 0 (CANBTR0)
and Section 9.3.2.4, “MSCAN Bus Timing Register 1 (CANBTR1)”).
Table 9-34 gives an overview of the CAN compliant segment settings and the related parameter values.
NOTE
It is the user’s responsibility to ensure the bit time settings are in compliance
with the CAN standard.
9.4.4 Modes of Operation
9.4.4.1 Normal Modes
The MSCAN module behaves as described within this specification in all normal system operation modes.
9.4.4.2 Special Modes
The MSCAN module behaves as described within this specification in all special system operation modes.
Table 9-33. Time Segment Syntax
Syntax Description
SYNC_SEG System expects transitions to occur on the CAN bus during this
period.
Transmit Point A node in transmit mode transfers a new value to the CAN bus at
this point.
Sample Point A node in receive mode samples the CAN bus at this point. If the
three samples per bit option is selected, then this point marks the
position of the third sample.
Table 9-34. CAN Standard Compliant Bit Time Segment Settings
Time Segment 1 TSEG1 Time Segment 2 TSEG2 Synchronization
Jump Width SJW
5 .. 10 4 .. 9 2 1 1 .. 2 0 .. 1
4 .. 11 3 .. 10 3 2 1 .. 3 0 .. 2
5 .. 12 4 .. 11 4 3 1 .. 4 0 .. 3
6 .. 13 5 .. 12 5 4 1 .. 4 0 .. 3
7 .. 14 6 .. 13 6 5 1 .. 4 0 .. 3
8 .. 15 7 .. 14 7 6 1 .. 4 0 .. 3
9 .. 16 8 .. 15 8 7 1 .. 4 0 .. 3
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
320 Freescale Semiconductor
9.4.4.3 Emulation Modes
In all emulation modes, the MSCAN module behaves just like normal system operation modes as
described within this specification.
9.4.4.4 Listen-Only Mode
In an optional CAN bus monitoring mode (listen-only), the CAN node is able to receive valid data frames
and valid remote frames, but it sends only “recessive” bits on the CAN bus. In addition, it cannot start a
transmision. If the MAC sub-layer is required to send a “dominant” bit (ACK bit, overload flag, or active
error flag), the bit is rerouted internally so that the MAC sub-layer monitors this “dominant” bit, although
the CAN bus may remain in recessive state externally.
9.4.4.5 Security Modes
The MSCAN module has no security features.
9.4.5 Low-Power Options
If the MSCAN is disabled (CANE = 0), the MSCAN clocks are stopped for power saving.
If the MSCAN is enabled (CANE = 1), the MSCAN has two additional modes with reduced power
consumption, compared to normal mode: sleep and power down mode. In sleep mode, power consumption
is reduced by stopping all clocks except those to access the registers from the CPU side. In power down
mode, all clocks are stopped and no power is consumed.
Table 9-35 summarizes the combinations of MSCAN and CPU modes. A particular combination of modes
is entered by the given settings on the CSWAI and SLPRQ/SLPAK bits.
For all modes, an MSCAN wake-up interrupt can occur only if the MSCAN is in sleep mode (SLPRQ = 1
and SLPAK = 1), wake-up functionality is enabled (WUPE = 1), and the wake-up interrupt is enabled
(WUPIE = 1).
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 321
9.4.5.1 Operation in Run Mode
As shown in Table 9-35, only MSCAN sleep mode is available as low power option when the CPU is in
run mode.
9.4.5.2 Operation in Wait Mode
The WAI instruction puts the MCU in a low power consumption stand-by mode. If the CSWAI bit is set,
additional power can be saved in power down mode because the CPU clocks are stopped. After leaving
this power down mode, the MSCAN restarts its internal controllers and enters normal mode again.
While the CPU is in wait mode, the MSCAN can be operated in normal mode and generate interrupts
(registers can be accessed via background debug mode). The MSCAN can also operate in any of the
low-power modes depending on the values of the SLPRQ/SLPAK and CSWAI bits as seen in Table 9-35.
9.4.5.3 Operation in Stop Mode
The STOP instruction puts the MCU in a low power consumption stand-by mode. In stop mode, the
MSCAN is set in power down mode regardless of the value of the SLPRQ/SLPAK and CSWAI bits
Table 9-35.
9.4.5.4 MSCAN Sleep Mode
The CPU can request the MSCAN to enter this low power mode by asserting the SLPRQ bit in the
CANCTL0 register. The time when the MSCAN enters sleep mode depends on a fixed synchronization
delay and its current activity:
Table 9-35. CPU vs. MSCAN Operating Modes
CPU Mode
MSCAN Mode
Normal
Reduced Power Consumption
Sleep Power Down Disabled
(CANE=0)
RUN CSWAI = X1
SLPRQ = 0
SLPAK = 0
1‘X’ means don’t care.
CSWAI = X
SLPRQ = 1
SLPAK = 1
CSWAI = X
SLPRQ = X
SLPAK = X
WAIT CSWAI = 0
SLPRQ = 0
SLPAK = 0
CSWAI = 0
SLPRQ = 1
SLPAK = 1
CSWAI = 1
SLPRQ = X
SLPAK = X
CSWAI = X
SLPRQ = X
SLPAK = X
STOP CSWAI = X
SLPRQ = X
SLPAK = X
CSWAI = X
SLPRQ = X
SLPAK = X
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
322 Freescale Semiconductor
If there are one or more message buffers scheduled for transmission (TXEx = 0), the MSCAN will
continue to transmit until all transmit message buffers are empty (TXEx = 1, transmitted
successfully or aborted) and then goes into sleep mode.
If the MSCAN is receiving, it continues to receive and goes into sleep mode as soon as the CAN
bus next becomes idle.
If the MSCAN is neither transmitting nor receiving, it immediately goes into sleep mode.
Figure 9-44. Sleep Request / Acknowledge Cycle
NOTE
The application software must avoid setting up a transmission (by clearing
one or more TXEx flag(s)) and immediately request sleep mode (by setting
SLPRQ). Whether the MSCAN starts transmitting or goes into sleep mode
directly depends on the exact sequence of operations.
If sleep mode is active, the SLPRQ and SLPAK bits are set (Figure 9-44). The application software must
use SLPAK as a handshake indication for the request (SLPRQ) to go into sleep mode.
When in sleep mode (SLPRQ = 1 and SLPAK = 1), the MSCAN stops its internal clocks. However, clocks
that allow register accesses from the CPU side continue to run.
If the MSCAN is in bus-off state, it stops counting the 128 occurrences of 11 consecutive recessive bits
due to the stopped clocks. The TXCAN pin remains in a recessive state. If RXF = 1, the message can be
read and RXF can be cleared. Shifting a new message into the foreground buffer of the receiver FIFO
(RxFG) does not take place while in sleep mode.
It is possible to access the transmit buffers and to clear the associated TXE flags. No message abort takes
place while in sleep mode.
If the WUPE bit in CANCLT0 is not asserted, the MSCAN will mask any activity it detects on CAN. The
RXCAN pin is therefore held internally in a recessive state. This locks the MSCAN in sleep mode
(Figure 9-45). WUPE must be set before entering sleep mode to take effect.
SYNC
SYNC
Bus Clock Domain CAN Clock Domain
MSCAN
in Sleep Mode
CPU
Sleep Request
SLPRQ
Flag
SLPAK
Flag
SLPRQ
sync.
SLPAK
sync.
SLPRQ
SLPAK
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 323
The MSCAN is able to leave sleep mode (wake up) only when:
CAN bus activity occurs and WUPE = 1
or
the CPU clears the SLPRQ bit
NOTE
The CPU cannot clear the SLPRQ bit before sleep mode (SLPRQ = 1 and
SLPAK = 1) is active.
After wake-up, the MSCAN waits for 11 consecutive recessive bits to synchronize to the CAN bus. As a
consequence, if the MSCAN is woken-up by a CAN frame, this frame is not received.
The receive message buffers (RxFG and RxBG) contain messages if they were received before sleep mode
was entered. All pending actions will be executed upon wake-up; copying of RxBG into RxFG, message
aborts and message transmissions. If the MSCAN remains in bus-off state after sleep mode was exited, it
continues counting the 128 occurrences of 11 consecutive recessive bits.
Figure 9-45. Simplified State Transitions for Entering/Leaving Sleep Mode
Wait
Idle
Tx/Rx
Message
Active
CAN Activity
CAN Activity &
Sleep
SLPRQ
StartUp for Idle
(CAN Activity & WUPE) |
(CAN Activity & WUPE) | SLPRQ
CAN Activity
CAN Activity
CAN Activity &
CAN Activity
SLPRQ
SLPRQ
CAN Activity
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
324 Freescale Semiconductor
9.4.5.5 MSCAN Initialization Mode
In initialization mode, any on-going transmission or reception is immediately aborted and synchronization
to the CAN bus is lost, potentially causing CAN protocol violations. To protect the CAN bus system from
fatal consequences of violations, the MSCAN immediately drives the TXCAN pin into a recessive state.
NOTE
The user is responsible for ensuring that the MSCAN is not active when
initialization mode is entered. The recommended procedure is to bring the
MSCAN into sleep mode (SLPRQ = 1 and SLPAK = 1) before setting the
INITRQ bit in the CANCTL0 register. Otherwise, the abort of an on-going
message can cause an error condition and can impact other CAN bus
devices.
In initialization mode, the MSCAN is stopped. However, interface registers remain accessible. This mode
is used to reset the CANCTL0, CANRFLG, CANRIER, CANTFLG, CANTIER, CANTARQ,
CANTAAK, and CANTBSEL registers to their default values. In addition, the MSCAN enables the
configuration of the CANBTR0, CANBTR1 bit timing registers; CANIDAC; and the CANIDAR,
CANIDMR message filters. See Section 9.3.2.1, “MSCAN Control Register 0 (CANCTL0),” for a
detailed description of the initialization mode.
Figure 9-46. Initialization Request/Acknowledge Cycle
Due to independent clock domains within the MSCAN, INITRQ must be synchronized to all domains by
using a special handshake mechanism. This handshake causes additional synchronization delay (see
Section Figure 9-46., “Initialization Request/Acknowledge Cycle”).
If there is no message transfer ongoing on the CAN bus, the minimum delay will be two additional bus
clocks and three additional CAN clocks. When all parts of the MSCAN are in initialization mode, the
INITAK flag is set. The application software must use INITAK as a handshake indication for the request
(INITRQ) to go into initialization mode.
NOTE
The CPU cannot clear INITRQ before initialization mode (INITRQ = 1 and
INITAK = 1) is active.
SYNC
SYNC
Bus Clock Domain CAN Clock Domain
CPU
Init Request
INIT
Flag
INITAK
Flag
INITRQ
sync.
INITAK
sync.
INITRQ
INITAK
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 325
9.4.5.6 MSCAN Power Down Mode
The MSCAN is in power down mode (Table 9-35) when
CPU is in stop mode
or
CPU is in wait mode and the CSWAI bit is set
When entering the power down mode, the MSCAN immediately stops all ongoing transmissions and
receptions, potentially causing CAN protocol violations. To protect the CAN bus system from fatal
consequences of violations to the above rule, the MSCAN immediately drives the TXCAN pin into a
recessive state.
NOTE
The user is responsible for ensuring that the MSCAN is not active when
power down mode is entered. The recommended procedure is to bring the
MSCAN into Sleep mode before the STOP or WAI instruction (if CSWAI
is set) is executed. Otherwise, the abort of an ongoing message can cause an
error condition and impact other CAN bus devices.
In power down mode, all clocks are stopped and no registers can be accessed. If the MSCAN was not in
sleep mode before power down mode became active, the module performs an internal recovery cycle after
powering up. This causes some fixed delay before the module enters normal mode again.
9.4.5.7 Programmable Wake-Up Function
The MSCAN can be programmed to wake up the MSCAN as soon as CAN bus activity is detected (see
control bit WUPE in Section 9.3.2.1, “MSCAN Control Register 0 (CANCTL0)”). The sensitivity to
existing CAN bus action can be modified by applying a low-pass filter function to the RXCAN input line
while in sleep mode (see control bit WUPM in Section 9.3.2.2, “MSCAN Control Register 1
(CANCTL1)”).
This feature can be used to protect the MSCAN from wake-up due to short glitches on the CAN bus lines.
Such glitches can result from—for example—electromagnetic interference within noisy environments.
9.4.6 Reset Initialization
The reset state of each individual bit is listed in Section 9.3.2, “Register Descriptions,” which details all
the registers and their bit-fields.
9.4.7 Interrupts
This section describes all interrupts originated by the MSCAN. It documents the enable bits and generated
flags. Each interrupt is listed and described separately.
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
326 Freescale Semiconductor
9.4.7.1 Description of Interrupt Operation
The MSCAN supports four interrupt vectors (see Table 9-36), any of which can be individually masked
(for details see sections from Section 9.3.2.6, “MSCAN Receiver Interrupt Enable Register (CANRIER),”
to Section 9.3.2.8, “MSCAN Transmitter Interrupt Enable Register (CANTIER)”).
NOTE
The dedicated interrupt vector addresses are defined in the Resets and
Interrupts chapter.
9.4.7.2 Transmit Interrupt
At least one of the three transmit buffers is empty (not scheduled) and can be loaded to schedule a message
for transmission. The TXEx flag of the empty message buffer is set.
9.4.7.3 Receive Interrupt
A message is successfully received and shifted into the foreground buffer (RxFG) of the receiver FIFO.
This interrupt is generated immediately after receiving the EOF symbol. The RXF flag is set. If there are
multiple messages in the receiver FIFO, the RXF flag is set as soon as the next message is shifted to the
foreground buffer.
9.4.7.4 Wake-Up Interrupt
A wake-up interrupt is generated if activity on the CAN bus occurs during MSCN internal sleep mode.
WUPE (see Section 9.3.2.1, “MSCAN Control Register 0 (CANCTL0)”) must be enabled.
9.4.7.5 Error Interrupt
An error interrupt is generated if an overrun of the receiver FIFO, error, warning, or bus-off condition
occurrs. Section 9.3.2.5, “MSCAN Receiver Flag Register (CANRFLG) indicates one of the following
conditions:
Overrun An overrun condition of the receiver FIFO as described in Section 9.4.2.3, “Receive
Structures,” occurred.
CAN Status Change — The actual value of the transmit and receive error counters control the
CAN bus state of the MSCAN. As soon as the error counters skip into a critical range
(Tx/Rx-warning, Tx/Rx-error, bus-off) the MSCAN flags an error condition. The status change,
which caused the error condition, is indicated by the TSTAT and RSTAT flags (see Section 9.3.2.5,
Table 9-36. Interrupt Vectors
Interrupt Source CCR Mask Local Enable
Wake-Up Interrupt (WUPIF) I bit CANRIER (WUPIE)
Error Interrupts Interrupt (CSCIF, OVRIF) I bit CANRIER (CSCIE, OVRIE)
Receive Interrupt (RXF) I bit CANRIER (RXFIE)
Transmit Interrupts (TXE[2:0]) I bit CANTIER (TXEIE[2:0])
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 327
“MSCAN Receiver Flag Register (CANRFLG) and Section 9.3.2.6, “MSCAN Receiver Interrupt
Enable Register (CANRIER)”).
9.4.7.6 Interrupt Acknowledge
Interrupts are directly associated with one or more status flags in either the Section 9.3.2.5, “MSCAN
Receiver Flag Register (CANRFLG)” or the Section 9.3.2.7, “MSCAN Transmitter Flag Register
(CANTFLG).” Interrupts are pending as long as one of the corresponding flags is set. The flags in
CANRFLG and CANTFLG must be reset within the interrupt handler to handshake the interrupt. The flags
are reset by writing a 1 to the corresponding bit position. A flag cannot be cleared if the respective
condition prevails.
NOTE
It must be guaranteed that the CPU clears only the bit causing the current
interrupt. For this reason, bit manipulation instructions (BSET) must not be
used to clear interrupt flags. These instructions may cause accidental
clearing of interrupt flags which are set after entering the current interrupt
service routine.
9.4.7.7 Recovery from Stop or Wait
The MSCAN can recover from stop or wait via the wake-up interrupt. This interrupt can only occur if the
MSCAN was in sleep mode (SLPRQ = 1 and SLPAK = 1) before entering power down mode, the wake-up
option is enabled (WUPE = 1), and the wake-up interrupt is enabled (WUPIE = 1).
9.5 Initialization/Application Information
9.5.1 MSCAN initialization
The procedure to initially start up the MSCAN module out of reset is as follows:
1. Assert CANE
2. Write to the configuration registers in initialization mode
3. Clear INITRQ to leave initialization mode and enter normal mode
If the configuration of registers which are writable in initialization mode needs to be changed only when
the MSCAN module is in normal mode:
1. Bring the module into sleep mode by setting SLPRQ and awaiting SLPAK to assert after the CAN
bus becomes idle.
2. Enter initialization mode: assert INITRQ and await INITAK
3. Write to the configuration registers in initialization mode
4. Clear INITRQ to leave initialization mode and continue in normal mode
Chapter 9 Freescale’s Scalable Controller Area Network (S12MSCANV2)
MC9S12KG128 Data Sheet, Rev. 1.16
328 Freescale Semiconductor
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 329
Chapter 10
Serial Communications Interface (S12SCIV2)
Block Description
Revision History
10.1 Introduction
This block guide provide an overview of serial communication interface (SCI) module. The SCI allows
asynchronous serial communications with peripheral devices and other CPUs.
10.1.1 Glossary
IRQ — Interrupt Request
LSB — Least Significant Bit
MSB — Most Significant Bit
NRZ — Non-Return-to-Zero
RZI — Return-to-Zero-Inverted
RXD — Receive Pin
SCI — Serial Communication Interface
TXD — Transmit Pin
Version
Number Revision
Date Effective
Date Author Description of Changes
02.06 11/15/2002 Update Table 4-3 to use more general module clock
frequency 25 MHz instead of 10.2 MHz
02.07 07/05/2003 Updated according to SRS3.0
02.08 04/16/2004 Update OR flag and PF falg description; Correct baud rate
tolerance in 4.5.5.1 and 4.5.5.2
02.09 02/21/2006 Fix fig1-8, SCIDRL reset value from 0x40 to 0x0
Chapter 10 Serial Communications Interface (S12SCIV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
330 Freescale Semiconductor
10.1.2 Features
The SCI includes these distinctive features:
Full-duplex operation
Standard mark/space non-return-to-zero (NRZ) format
13-bit baud rate selection
Programmable 8-bit or 9-bit data format
Separately enabled transmitter and receiver
Programmable transmitter output parity
Two receiver wake up methods:
Idle line wake-up
Address mark wake-up
Interrupt-driven operation with eight flags:
Transmitter empty
Transmission complete
Receiver full
Idle receiver input
Receiver overrun
Noise error
Framing error
Parity error
Receiver framing error detection
Hardware parity checking
1/16 bit-time noise detection
10.1.3 Modes of Operation
The SCI operation is the same independent of device resource mapping and bus interface mode. Different
power modes are available to facilitate power saving.
10.1.3.1 Run Mode
Normal mode of operation.
10.1.3.2 Wait Mode
SCI operation in wait mode depends on the state of the SCISWAI bit in the SCI control register 1
(SCICR1).
If SCISWAI is clear, the SCI operates normally when the CPU is in wait mode.
Chapter 10 Serial Communications Interface (S12SCIV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 331
If SCISWAI is set, SCI clock generation ceases and the SCI module enters a power-conservation
state when the CPU is in wait mode. Setting SCISWAI does not affect the state of the receiver
enable bit, RE, or the transmitter enable bit, TE.
If SCISWAI is set, any transmission or reception in progress stops at wait mode entry. The
transmission or reception resumes when either an internal or external interrupt brings the CPU out
of wait mode. Exiting wait mode by reset aborts any transmission or reception in progress and
resets the SCI.
10.1.3.3 Stop Mode
The SCI is inactive during stop mode for reduced power consumption. The STOP instruction does not
affect the SCI register states, but the SCI module clock will be disabled. The SCI operation resumes from
where it left off after an external interrupt brings the CPU out of stop mode. Exiting stop mode by reset
aborts any transmission or reception in progress and resets the SCI.
10.1.4 Block Diagram
Figure 10-1 is a high level block diagram of the SCI module, showing the interaction of various functional
blocks.
Figure 10-1. SCI Block Diagram
SCI DATA REGISTER
RECEIVE SHIFT REGISTER
RECEIVE & WAKE UP CONTROL
DATA FORMAT CONTROL
TRANSMIT CONTROL
TRANSMIT SHIFT REGISTER
SCI DATA REGISTER
BAUD
GENERATOR
RX DATA IN
÷16
BUS CLOCK
TXDATA OUT
IDLE IRQ
RDR/OR IRQ
TDRE IRQ
TC IRQ
ORING
IRQ GENERATION IRQ GENERATION
IRQ
TO CPU
Chapter 10 Serial Communications Interface (S12SCIV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
332 Freescale Semiconductor
10.2 External Signal Description
The SCI module has a total of two external pins:
10.2.1 TXD-SCI Transmit Pin
This pin serves as transmit data output of SCI.
10.2.2 RXD-SCI Receive Pin
This pin serves as receive data input of the SCI.
Chapter 10 Serial Communications Interface (S12SCIV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 333
10.3 Memory Map and Registers
This section provides a detailed description of all memory and registers.
10.3.1 Module Memory Map
The memory map for the SCI module is given below in Figure 10-2. The Address listed for each register
is the address offset. The total address for each register is the sum of the base address for the SCI module
and the address offset for each register.
10.3.2 Register Descriptions
This section consists of register descriptions in address order. Each description includes a standard register
diagram with an associated figure number. Writes to a reserved register location do not have any effect and
reads of these locations return a zero. Details of register bit and field function follow the register diagrams,
in bit order.
Address Name Bit 7 65432 1Bit 0
0x0000 SCIBDH R0 0 0 SBR12 SBR11 SBR10 SBR9 SBR8
W
0x0001 SCIBDL RSBR7 SBR6 SBR5 SBR4 SBR3 SBR2 SBR1 SBR0
W
0x0002 SCICR1 RLOOPS SCISWAI RSRC M WAKE ILT PE PT
W
0x0003 SCICR2 RTIE TCIE RIE ILIE TE RE RWU SBK
W
0x0004 SCISR1 R TDRE TC RDRF IDLE OR NF FE PF
W
0x0005 SCISR2 R0 0000
BRK13 TXDIR RAF
W
0x0006 SCIDRH RR8 T8 0000 0 0
W
0x0007 SCIDRL RR7 R6R5R4R3R2 R1 R0
WT7 T6T5T4T3T2 T1 T0
= Unimplemented or Reserved
Figure 10-2. SCI Register Summary
Chapter 10 Serial Communications Interface (S12SCIV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
334 Freescale Semiconductor
10.3.2.1 SCI Baud Rate Registers (SCIBDH and SCHBDL)
The SCI Baud Rate Register is used by the counter to determine the baud rate of the SCI. The formula for
calculating the baud rate is:
SCI baud rate = SCI module clock / (16 x BR)
where:
BR is the content of the SCI baud rate registers, bits SBR12 through SBR0. The baud rate registers
can contain a value from 1 to 8191.
Read: Anytime. If only SCIBDH is written to, a read will not return the correct data until SCIBDL is
written to as well, following a write to SCIBDH.
Write: Anytime
Module Base + 0x_0000
76543210
R000
SBR12 SBR11 SBR10 SBR9 SBR8
W
Reset 0 0 0 00000
Module Base + 0x_0001
76543210
RSBR7 SBR6 SBR5 SBR4 SBR3 SBR2 SBR1 SBR0
W
Reset 0 0 0 00100
= Unimplemented or Reserved
Figure 10-3. SCI Baud Rate Registers (SCIBDH and SCIBDL)
Table 10-1. SCIBDH AND SCIBDL Field Descriptions
Field Description
4–0
7–0
SBR[12:0]
SCI Baud Rate Bits — The baud rate for the SCI is determined by these 13 bits.
Note: The baud rate generator is disabled until the TE bit or the RE bit is set for the first time after reset. The
baud rate generator is disabled when BR = 0.
Writing to SCIBDH has no effect without writing to SCIBDL, since writing to SCIBDH puts the data in a
temporary location until SCIBDL is written to.
Chapter 10 Serial Communications Interface (S12SCIV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 335
10.3.2.2 SCI Control Register 1 (SCICR1)
Read: Anytime
Write: Anytime
Module Base + 0x_0002
76543210
RLOOPS SCISWAI RSRC M WAKE ILT PE PT
W
Reset 0 0 0 00000
Figure 10-4. SCI Control Register 1 (SCICR1)
Table 10-2. SCICR1 Field Descriptions
Field Description
7
LOOPS Loop Select Bit LOOPS enables loop operation.In loop operation, the RXD pin is disconnected from the SCI
and the transmitter output is internally connected to the receiver input. Both the transmitter and the receiver must
be enabled to use the loop function.See Table 10-3.
0 Normal operation enabled
1 Loop operation enabled
Note: The receiver input is determined by the RSRC bit.
6
SCISWAI SCI Stop in Wait Mode Bit — SCISWAI disables the SCI in wait mode.
0 SCI enabled in wait mode
1 SCI disabled in wait mode
5
RSRC Receiver Source Bit — When LOOPS = 1, the RSRC bit determines the source for the receiver shift register
input.
0 Receiver input internally connected to transmitter output
1 Receiver input connected externally to transmitter
4
MData Format Mode Bit — MODE determines whether data characters are eight or nine bits long.
0 One start bit, eight data bits, one stop bit
1 One start bit, nine data bits, one stop bit
3
WAKE Wakeup Condition Bit WAKE determines which condition wakes up the SCI: a logic 1 (address mark) in the
most significant bit position of a received data character or an idle condition on the RXD.
0 Idle line wakeup
1 Address mark wakeup
2
ILT Idle Line Type Bit — ILT determines when the receiver starts counting logic 1s as idle character bits. The
counting begins either after the start bit or after the stop bit. If the count begins after the start bit, then a string of
logic 1s preceding the stop bit may cause false recognition of an idle character. Beginning the count after the
stop bit avoids false idle character recognition, but requires properly synchronized transmissions.
0 Idle character bit count begins after start bit
1 Idle character bit count begins after stop bit
1
PE Parity Enable Bit PE enables the parity function. When enabled, the parity function inserts a parity bit in the
most significant bit position.
0 Parity function disabled
1 Parity function enabled
0
PT Parity Type Bit PT determines whether the SCI generates and checks for even parity or odd parity. With even
parity, an even number of 1s clears the parity bit and an odd number of 1s sets the parity bit. With odd parity, an
odd number of 1s clears the parity bit and an even number of 1s sets the parity bit.
0 Even parity
1 Odd parity
Chapter 10 Serial Communications Interface (S12SCIV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
336 Freescale Semiconductor
10.3.2.3 SCI Control Register 2 (SCICR2)
Read: Anytime
Write: Anytime
Table 10-3. Loop Functions
LOOPS RSRC Function
0 x Normal operation
1 0 Loop mode with Rx input internally connected to Tx output
1 1 Single-wire mode with Rx input connected to TXD
Module Base + 0x_0003
76543210
RTIE TCIE RIE ILIE TE RE RWU SBK
W
Reset 0 0 0 00000
Figure 10-5. SCI Control Register 2 (SCICR2)
Table 10-4. SCICR2 Field Descriptions
Field Description
7
TIE Transmitter Interrupt Enable Bit — TIE enables the transmit data register empty flag, TDRE, to generate
interrupt requests.
0 TDRE interrupt requests disabled
1 TDRE interrupt requests enabled
6
TCIE Transmission Complete Interrupt Enable Bit TCIE enables the transmission complete flag, TC, to generate
interrupt requests.
0 TC interrupt requests disabled
1 TC interrupt requests enabled
5
RIE Receiver Full Interrupt Enable Bit RIE enables the receive data register full flag, RDRF, or the overrun flag,
OR, to generate interrupt requests.
0 RDRF and OR interrupt requests disabled
1 RDRF and OR interrupt requests enabled
4
ILIE Idle Line Interrupt Enable Bit — ILIE enables the idle line flag, IDLE, to generate interrupt requests.
0 IDLE interrupt requests disabled
1 IDLE interrupt requests enabled
3
TE Transmitter Enable Bit — TE enables the SCI transmitter and configures the TXD pin as being controlled by
the SCI. The TE bit can be used to queue an idle preamble.
0 Transmitter disabled
1 Transmitter enabled
2
RE Receiver Enable Bit — RE enables the SCI receiver.
0 Receiver disabled
1 Receiver enabled
Chapter 10 Serial Communications Interface (S12SCIV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 337
10.3.2.4 SCI Status Register 1 (SCISR1)
The SCISR1 and SCISR2 registers provides inputs to the MCU for generation of SCI interrupts. Also,
these registers can be polled by the MCU to check the status of these bits. The flag-clearing procedures
require that the status register be read followed by a read or write to the SCI Data Register.It is permissible
to execute other instructions between the two steps as long as it does not compromise the handling of I/O,
but the order of operations is important for flag clearing.
Read: Anytime
Write: Has no meaning or effect
1
RWU Receiver Wakeup Bit — Standby state
0 Normal operation.
1 RWU enables the wakeup function and inhibits further receiver interrupt requests. Normally, hardware wakes
the receiver by automatically clearing RWU.
0
SBK Send Break Bit — Toggling SBK sends one break character (10 or 11 logic 0s, respectively 13 or 14 logics 0s
if BRK13 is set). Toggling implies clearing the SBK bit before the break character has finished transmitting. As
long as SBK is set, the transmitter continues to send complete break characters (10 or 11 bits, respectively 13
or 14 bits).
0 No break characters
1 Transmit break characters
Module Base + 0x_0004
76543210
R TDRE TC RDRF IDLE OR NF FE PF
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 10-6. SCI Status Register 1 (SCISR1)
Table 10-5. SCISR1 Field Descriptions
Field Description
7
TDRE Transmit Data Register Empty Flag — TDRE is set when the transmit shift register receives a byte from the
SCI data register. When TDRE is 1, the transmit data register (SCIDRH/L) is empty and can receive a new value
to transmit.Clear TDRE by reading SCI status register 1 (SCISR1), with TDRE set and then writing to SCI data
register low (SCIDRL).
0 No byte transferred to transmit shift register
1 Byte transferred to transmit shift register; transmit data register empty
6
TC Transmit Complete Flag TC is set low when there is a transmission in progress or when a preamble or break
character is loaded. TC is set high when the TDRE flag is set and no data, preamble, or break character is being
transmitted.When TC is set, the TXD out signal becomes idle (logic 1). Clear TC by reading SCI status register
1 (SCISR1) with TC set and then writing to SCI data register low (SCIDRL). TC is cleared automatically when
data, preamble, or break is queued and ready to be sent. TC is cleared in the event of a simultaneous set and
clear of the TC flag (transmission not complete).
0 Transmission in progress
1 No transmission in progress
Table 10-4. SCICR2 Field Descriptions (continued)
Field Description
Chapter 10 Serial Communications Interface (S12SCIV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
338 Freescale Semiconductor
5
RDRF Receive Data Register Full Flag RDRF is set when the data in the receive shift register transfers to the SCI
data register. Clear RDRF by reading SCI status register 1 (SCISR1) with RDRF set and then reading SCI data
register low (SCIDRL).
0 Data not available in SCI data register
1 Received data available in SCI data register
4
IDLE Idle Line Flag — IDLE is set when 10 consecutive logic 1s (if M=0) or 11 consecutive logic 1s (if M=1) appear
on the receiver input. Once the IDLE flag is cleared, a valid frame must again set the RDRF flag before an idle
condition can set the IDLE flag.Clear IDLE by reading SCI status register 1 (SCISR1) with IDLE set and then
reading SCI data register low (SCIDRL).
0 Receiver input is either active now or has never become active since the IDLE flag was last cleared
1 Receiver input has become idle
Note: When the receiver wakeup bit (RWU) is set, an idle line condition does not set the IDLE flag.
3
OR Overrun Flag — OR is set when software fails to read the SCI data register before the receive shift register
receives the next frame. The OR bit is set immediately after the stop bit has been completely received for the
second frame. The data in the shift register is lost, but the data already in the SCI data registers is not affected.
Clear OR by reading SCI status register 1 (SCISR1) with OR set and then reading SCI data register low
(SCIDRL).
0 No overrun
1 Overrun
Note: OR flag may read back as set when RDRF flag is clear. This may happen if the following sequence of
events occurs:
1. After the first frame is received, read status register SCISR1 (returns RDRF set and OR flag clear);
2. Receive second frame without reading the first frame in the data register (the second frame is not
received and OR flag is set);
3. Read data register SCIDRL (returns first frame and clears RDRF flag in the status register);
4. Read status register SCISR1 (returns RDRF clear and OR set).
Event 3 may be at exactly the same time as event 2 or any time after. When this happens, a dummy
SCIDRL read following event 4 will be required to clear the OR flag if further frames are to be received.
2
NF Noise Flag NF is set when the SCI detects noise on the receiver input. NF bit is set during the same cycle as
the RDRF flag but does not get set in the case of an overrun. Clear NF by reading SCI status register 1(SCISR1),
and then reading SCI data register low (SCIDRL).
0 No noise
1 Noise
1
FE Framing Error Flag FE is set when a logic 0 is accepted as the stop bit. FE bit is set during the same cycle
as the RDRF flag but does not get set in the case of an overrun. FE inhibits further data reception until it is
cleared. Clear FE by reading SCI status register 1 (SCISR1) with FE set and then reading the SCI data register
low (SCIDRL).
0 No framing error
1 Framing error
0
PF Parity Error Flag PF is set when the parity enable bit (PE) is set and the parity of the received data does not
match the parity type bit (PT). PF bit is set during the same cycle as the RDRF flag but does not get set in the
case of an overrun. Clear PF by reading SCI status register 1 (SCISR1), and then reading SCI data register low
(SCIDRL).
0 No parity error
1 Parity error
Table 10-5. SCISR1 Field Descriptions (continued)
Field Description
Chapter 10 Serial Communications Interface (S12SCIV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 339
10.3.2.5 SCI Status Register 2 (SCISR2)
Read: Anytime
Write: Anytime; writing accesses SCI status register 2; writing to any bits except TXDIR and BRK13
(SCISR2[1] & [2]) has no effect
Module Base + 0x_0005
76543210
R00000
BK13 TXDIR RAF
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 10-7. SCI Status Register 2 (SCISR2)
Table 10-6. SCISR2 Field Descriptions
Field Description
2
BK13 Break Transmit Character Length — This bit determines whether the transmit break character is 10 or 11 bit
respectively 13 or 14 bits long. The detection of a framing error is not affected by this bit.
0 Break Character is 10 or 11 bit long
1 Break character is 13 or 14 bit long
1
TXDIR Transmitter Pin Data Direction in Single-Wire Mode. This bit determines whether the TXD pin is going to
be used as an input or output, in the Single-Wire mode of operation. This bit is only relevant in the Single-Wire
mode of operation.
0 TXD pin to be used as an input in Single-Wire mode
1 TXD pin to be used as an output in Single-Wire mode
0
RAF Receiver Active Flag RAF is set when the receiver detects a logic 0 during the RT1 time period of the start
bit search. RAF is cleared when the receiver detects an idle character.
0 No reception in progress
1 Reception in progress
Chapter 10 Serial Communications Interface (S12SCIV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
340 Freescale Semiconductor
10.3.2.6 SCI Data Registers (SCIDRH and SCIDRL)
Read: Anytime; reading accesses SCI receive data register
Write: Anytime; writing accesses SCI transmit data register; writing to R8 has no effect
NOTE
If the value of T8 is the same as in the previous transmission, T8 does not
have to be rewritten.The same value is transmitted until T8 is rewritten
In 8-bit data format, only SCI data register low (SCIDRL) needs to be
accessed.
When transmitting in 9-bit data format and using 8-bit write instructions,
write first to SCI data register high (SCIDRH), then SCIDRL.
Module Base + 0x_0006
76543210
RR8 T8 000000
W
Reset 0 0 0 00000
Module Base + 0x_0007
76543210
RR7R6R5R4R3R2R1R0
W T7 T6 T5 T4 T3 T2 T1 T0
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 10-8. SCI Data Registers (SCIDRH and SCIDRL)
Table 10-7. SCIDRH AND SCIDRL Field Descriptions
Field Description
7
R8 Received Bit 8 — R8 is the ninth data bit received when the SCI is configured for 9-bit data format (M = 1).
6
T8 Transmit Bit 8 — T8 is the ninth data bit transmitted when the SCI is configured for 9-bit data format (M = 1).
7–0
R[7:0]
T[7:0]
Received Bits — Received bits seven through zero for 9-bit or 8-bit data formats
Transmit Bits — Transmit bits seven through zero for 9-bit or 8-bit formats
Chapter 10 Serial Communications Interface (S12SCIV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 341
10.4 Functional Description
This section provides a complete functional description of the SCI block, detailing the operation of the
design from the end user perspective in a number of subsections.
Figure 10-9 shows the structure of the SCI module. The SCI allows full duplex, asynchronous, NRZ serial
communication between the CPU and remote devices, including other CPUs. The SCI transmitter and
receiver operate independently, although they use the same baud rate generator. The CPU monitors the
status of the SCI, writes the data to be transmitted, and processes received data.
Figure 10-9. SCI Block Diagram
SCI DATA
RECEIVE
SHIFT REGISTER
SCI DATA
REGISTER
TRANSMIT
SHIFT REGISTER
REGISTER
BAUD RATE
GENERATOR
SBR12–SBR0
BUS
TRANSMIT
CONTROL
÷16
RECEIVE
AND WAKEUP
DATA FORMAT
CONTROL
CONTROL
T8
PF
FE
NF
RDRF
IDLE
TIE
OR
TCIE
TDRE
TC
R8
RAF
LOOPS
RWU
RE
PE
ILT
PT
WAKE
M
CLOCK
ILIE
RIE
RXD
RSRC
SBK
LOOPS
TE
RSRC
TXD
RDRF/OR IRQ
TDRE IRQ
IDLE IRQ
TC IRQ
IRQ
TO CPU
Chapter 10 Serial Communications Interface (S12SCIV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
342 Freescale Semiconductor
10.4.1 Data Format
The SCI uses the standard NRZ mark/space data format illustrated in Figure 10-10 below.
Figure 10-10. SCI Data Formats
Each data character is contained in a frame that includes a start bit, eight or nine data bits, and a stop bit.
Clearing the M bit in SCI control register 1 configures the SCI for 8-bit data characters.A frame with eight
data bits has a total of 10 bits. Setting the M bit configures the SCI for nine-bit data characters. A frame
with nine data bits has a total of 11 bits
When the SCI is configured for 9-bit data characters, the ninth data bit is the T8 bit in SCI data register
high (SCIDRH). It remains unchanged after transmission and can be used repeatedly without rewriting it.
A frame with nine data bits has a total of 11 bits.
Table 10-9. Example of 9-Bit Data Formats
Table 10-8. Example of 8-Bit Data Formats
Start
Bit Data
Bits Address
Bits Parity
Bits Stop
Bit
18 0 0 1
17 0 1 1
17 1
1
1The address bit identifies the frame as an address character. See
Section 10.4.4.6, “Receiver Wakeup”.
01
Start
Bit Data
Bits Address
Bits Parity
Bits Stop
Bit
19 0 0 1
18 0 1 1
18 1
1
1The address bit identifies the frame as an address character. See
Section 10.4.4.6, “Receiver Wakeup”.
01
BIT 5
START
BIT BIT 0 BIT 1
NEXT
STOP
BIT
START
BIT
9-BIT DATA FORMAT
BIT 2 BIT 3 BIT 4 BIT 6 BIT 7
PARITY
OR DATA
BIT
PARITY
OR DATA
BIT
BIT M IN SCICR1 SET
8-BIT DATA FORMAT
BIT M IN SCICR1 CLEAR
BIT 5BIT 0 BIT 1 BIT 2 BIT 3 BIT 4 BIT 6 BIT 7 BIT 8 STOP
BIT
NEXT
START
BIT
START
BIT
Chapter 10 Serial Communications Interface (S12SCIV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 343
10.4.2 Baud Rate Generation
A 13-bit modulus counter in the baud rate generator derives the baud rate for both the receiver and the
transmitter. The value from 0 to 8191 written to the SBR12–SBR0 bits determines the module clock
divisor. The SBR bits are in the SCI baud rate registers (SCIBDH and SCIBDL). The baud rate clock is
synchronized with the bus clock and drives the receiver. The baud rate clock divided by 16 drives the
transmitter. The receiver has an acquisition rate of 16 samples per bit time.
Baud rate generation is subject to one source of error:
Integer division of the module clock may not give the exact target frequency.
Table 10-10 lists some examples of achieving target baud rates with a module clock frequency of 25 MHz
SCI baud rate = SCI module clock / (16 * SCIBR[12:0])
Table 10-10. Baud Rates (Example: Module Clock = 25 MHz)
Bits
SBR[12-0] Receiver
Clock (Hz) Transmitter
Clock (Hz) Target Baud
Rate Error
(%)
41 609,756.1 38,109.8 38,400 .76
81 308,642.0 19,290.1 19,200 .47
163 153,374.2 9585.9 9600 .16
326 76,687.1 4792.9 4800 .15
651 38,402.5 2400.2 2400 .01
1302 19,201.2 1200.1 1200 .01
2604 9600.6 600.0 600 .00
5208 4800.0 300.0 300 .00
Chapter 10 Serial Communications Interface (S12SCIV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
344 Freescale Semiconductor
10.4.3 Transmitter
Figure 10-11. Transmitter Block Diagram
10.4.3.1 Transmitter Character Length
The SCI transmitter can accommodate either 8-bit or 9-bit data characters. The state of the M bit in SCI
control register 1 (SCICR1) determines the length of data characters. When transmitting 9-bit data, bit T8
in SCI data register high (SCIDRH) is the ninth bit (bit 8).
10.4.3.2 Character Transmission
To transmit data, the MCU writes the data bits to the SCI data registers (SCIDRH/SCIDRL), which in turn
are transferred to the transmitter shift register. The transmit shift register then shifts a frame out through
the Tx output signal, after it has prefaced them with a start bit and appended them with a stop bit. The SCI
data registers (SCIDRH and SCIDRL) are the write-only buffers between the internal data bus and the
transmit shift register.
The SCI also sets a flag, the transmit data register empty flag (TDRE), every time it transfers data from
the buffer (SCIDRH/L) to the transmitter shift register.The transmit driver routine may respond to this flag
PE
PT
H876543210L
11-BIT TRANSMIT SHIFT REGISTER
STOP
START
T8
TDRE
TIE
TCIE
SBK
TC
PARITY
GENERATION
MSB
SCI DATA REGISTERS
LOAD FROM SCIDR
SHIFT ENABLE
PREAMBLE (ALL ONES)
BREAK (ALL 0s)
TRANSMITTER CONTROL
M
INTERNAL BUS
SBR12–SBR0
BAUD DIVIDER ÷ 16
TDRE INTERRUPT REQUEST
TC INTERRUPT REQUEST
BUS
LOOP
RSRC
CLOCK
TE
TO
CONTROL RXD
LOOPS
TXD
Chapter 10 Serial Communications Interface (S12SCIV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 345
by writing another byte to the Transmitter buffer (SCIDRH/SCIDRL), while the shift register is still
shifting out the first byte.
To initiate an SCI transmission:
1. Configure the SCI:
a) Select a baud rate. Write this value to the SCI baud registers (SCIBDH/L) to begin the baud
rate generator. Remember that the baud rate generator is disabled when the baud rate is zero.
Writing to the SCIBDH has no effect without also writing to SCIBDL.
b) Write to SCICR1 to configure word length, parity, and other configuration bits
(LOOPS,RSRC,M,WAKE,ILT,PE,PT).
c) Enable the transmitter, interrupts, receive, and wake up as required, by writing to the SCICR2
register bits (TIE,TCIE,RIE,ILIE,TE,RE,RWU,SBK). A preamble or idle character will now
be shifted out of the transmitter shift register.
2. Transmit Procedure for Each Byte:
a. Poll the TDRE flag by reading the SCISR1 or responding to the TDRE interrupt. Keep in mind
that the TDRE bit resets to one.
d) If the TDRE flag is set, write the data to be transmitted to SCIDRH/L, where the ninth bit is
written to the T8 bit in SCIDRH if the SCI is in 9-bit data format. A new transmission will not
result until the TDRE flag has been cleared.
3. Repeat step 2 for each subsequent transmission.
NOTE
The TDRE flag is set when the shift register is loaded with the next data to
be transmitted from SCIDRH/L, which happens, generally speaking, a little
over half-way through the stop bit of the previous frame. Specifically, this
transfer occurs 9/16ths of a bit time AFTER the start of the stop bit of the
previous frame.
Writing the TE bit from 0 to a 1 automatically loads the transmit shift register with a preamble of 10 logic
1s (if M = 0) or 11 logic 1s (if M = 1). After the preamble shifts out, control logic transfers the data from
the SCI data register into the transmit shift register. A logic 0 start bit automatically goes into the least
significant bit position of the transmit shift register. A logic 1 stop bit goes into the most significant bit
position.
Hardware supports odd or even parity. When parity is enabled, the most significant bit (msb) of the data
character is the parity bit.
The transmit data register empty flag, TDRE, in SCI status register 1 (SCISR1) becomes set when the SCI
data register transfers a byte to the transmit shift register. The TDRE flag indicates that the SCI data
register can accept new data from the internal data bus. If the transmit interrupt enable bit, TIE, in SCI
control register 2 (SCICR2) is also set, the TDRE flag generates a transmitter interrupt request.
When the transmit shift register is not transmitting a frame, the Tx output signal goes to the idle condition,
logic 1. If at any time software clears the TE bit in SCI control register 2 (SCICR2), the transmitter enable
signal goes low and the transmit signal goes idle.
Chapter 10 Serial Communications Interface (S12SCIV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
346 Freescale Semiconductor
If software clears TE while a transmission is in progress (TC = 0), the frame in the transmit shift register
continues to shift out. To avoid accidentally cutting off the last frame in a message, always wait for TDRE
to go high after the last frame before clearing TE.
To separate messages with preambles with minimum idle line time, use this sequence between messages:
1. Write the last byte of the first message to SCIDRH/L.
2. Wait for the TDRE flag to go high, indicating the transfer of the last frame to the transmit shift
register.
3. Queue a preamble by clearing and then setting the TE bit.
4. Write the first byte of the second message to SCIDRH/L.
10.4.3.3 Break Characters
Writing a logic 1 to the send break bit, SBK, in SCI control register 2 (SCICR2) loads the transmit shift
register with a break character. A break character contains all logic 0s and has no start, stop, or parity bit.
Break character length depends on the M bit in SCI control register 1 (SCICR1). As long as SBK is at
logic 1, transmitter logic continuously loads break characters into the transmit shift register. After software
clears the SBK bit, the shift register finishes transmitting the last break character and then transmits at least
one logic 1. The automatic logic 1 at the end of a break character guarantees the recognition of the start bit
of the next frame.
The SCI recognizes a break character when a start bit is followed by eight or nine logic 0 data bits and a
logic 0 where the stop bit should be. Receiving a break character has these effects on SCI registers:
Sets the framing error flag, FE
Sets the receive data register full flag, RDRF
Clears the SCI data registers (SCIDRH/L)
May set the overrun flag, OR, noise flag, NF, parity error flag, PE, or the receiver active flag, RAF
(see Section 10.3.2.4, “SCI Status Register 1 (SCISR1)” and Section 10.3.2.5, “SCI Status
Register 2 (SCISR2)”
10.4.3.4 Idle Characters
An idle character contains all logic 1s and has no start, stop, or parity bit. Idle character length depends on
the M bit in SCI control register 1 (SCICR1). The preamble is a synchronizing idle character that begins
the first transmission initiated after writing the TE bit from 0 to 1.
If the TE bit is cleared during a transmission, the Tx output signal becomes idle after completion of the
transmission in progress. Clearing and then setting the TE bit during a transmission queues an idle
character to be sent after the frame currently being transmitted.
Chapter 10 Serial Communications Interface (S12SCIV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 347
NOTE
When queueing an idle character, return the TE bit to logic 1 before the stop
bit of the current frame shifts out through the Tx output signal. Setting TE
after the stop bit appears on Tx output signal causes data previously written
to the SCI data register to be lost. Toggle the TE bit for a queued idle
character while the TDRE flag is set and immediately before writing the
next byte to the SCI data register.
NOTE
If the TE bit is clear and the transmission is complete, the SCI is not the
master of the TXD pin
10.4.4 Receiver
Figure 10-12. SCI Receiver Block Diagram
10.4.4.1 Receiver Character Length
The SCI receiver can accommodate either 8-bit or 9-bit data characters. The state of the M bit in SCI
control register 1 (SCICR1) determines the length of data characters. When receiving 9-bit data, bit R8 in
SCI data register high (SCIDRH) is the ninth bit (bit 8).
ALL ONES
M
WAKE
ILT
PE
PT
RE
H876543210L
11-BIT RECEIVE SHIFT REGISTER
STOP
START
DATA
WAKEUP
PARITY
CHECKING
MSB
SCI DATA REGISTER
R8
RIE
ILIE
RWU
RDRF
OR
NF
FE
PE
INTERNAL
BUS
BUS
IDLE INTERRUPT REQUEST
RDRF/OR INTERRUPT REQUEST
SBR12–SBR0
BAUD DIVIDER
LOOP
RSRC
FROM TXD
CLOCK
IDLE
RAF
RECOVERY
CONTROL
LOGIC
LOOPS
RXD
Chapter 10 Serial Communications Interface (S12SCIV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
348 Freescale Semiconductor
10.4.4.2 Character Reception
During an SCI reception, the receive shift register shifts a frame in from the Rx input signal. The SCI data
register is the read-only buffer between the internal data bus and the receive shift register.
After a complete frame shifts into the receive shift register, the data portion of the frame transfers to the
SCI data register. The receive data register full flag, RDRF, in SCI status register 1 (SCISR1) becomes set,
indicating that the received byte can be read. If the receive interrupt enable bit, RIE, in SCI control
register 2 (SCICR2) is also set, the RDRF flag generates an RDRF interrupt request.
10.4.4.3 Data Sampling
The receiver samples the Rx input signal at the RT clock rate. The RT clock is an internal signal with a
frequency 16 times the baud rate. To adjust for baud rate mismatch, the RT clock (see Figure 10-13) is
re-synchronized:
After every start bit
After the receiver detects a data bit change from logic 1 to logic 0 (after the majority of data bit
samples at RT8, RT9, and RT10 returns a valid logic 1 and the majority of the next RT8, RT9, and
RT10 samples returns a valid logic 0)
To locate the start bit, data recovery logic does an asynchronous search for a logic 0 preceded by three
logic 1s.When the falling edge of a possible start bit occurs, the RT clock begins to count to 16.
Figure 10-13. Receiver Data Sampling
To verify the start bit and to detect noise, data recovery logic takes samples at RT3, RT5, and RT7.
Table 10-11 summarizes the results of the start bit verification samples.
Table 10-11. Start Bit Verification
RT3, RT5, and RT7 Samples Start Bit Verification Noise Flag
000 Yes 0
001 Yes 1
010 Yes 1
011 No 0
RESET RT CLOCK
RT1
RT1
RT1
RT1
RT1
RT1
RT1
RT1
RT1
RT2
RT3
RT4
RT5
RT8
RT7
RT6
RT11
RT10
RT9
RT15
RT14
RT13
RT12
RT16
RT1
RT2
RT3
RT4
SAMPLES
RT CLOCK
RT CLOCK COUNT
START BIT
Rx Input Signal
START BIT
QUALIFICATION
START BIT DATA
SAMPLING
111111110000000
LSB
VERIFICATION
Chapter 10 Serial Communications Interface (S12SCIV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 349
If start bit verification is not successful, the RT clock is reset and a new search for a start bit begins.
To determine the value of a data bit and to detect noise, recovery logic takes samples at RT8, RT9, and
RT10. Table 10-12 summarizes the results of the data bit samples.
NOTE
The RT8, RT9, and RT10 samples do not affect start bit verification. If any
or all of the RT8, RT9, and RT10 start bit samples are logic 1s following a
successful start bit verification, the noise flag (NF) is set and the receiver
assumes that the bit is a start bit (logic 0).
To verify a stop bit and to detect noise, recovery logic takes samples at RT8, RT9, and RT10. Table 10-13
summarizes the results of the stop bit samples.
Table 10-13. Stop Bit Recovery
100 Yes 1
101 No 0
110 No 0
111 No 0
Table 10-12. Data Bit Recovery
RT8, RT9, and RT10 Samples Data Bit Determination Noise Flag
000 0 0
001 0 1
010 0 1
011 1 1
100 0 1
101 1 1
110 1 1
111 1 0
RT8, RT9, and RT10 Samples Framing Error Flag Noise Flag
000 1 0
001 1 1
010 1 1
011 0 1
100 1 1
101 0 1
110 0 1
111 0 0
Table 10-11. Start Bit Verification
RT3, RT5, and RT7 Samples Start Bit Verification Noise Flag
Chapter 10 Serial Communications Interface (S12SCIV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
350 Freescale Semiconductor
In Figure 10-14 the verification samples RT3 and RT5 determine that the first low detected was noise and
not the beginning of a start bit. The RT clock is reset and the start bit search begins again. The noise flag
is not set because the noise occurred before the start bit was found.
Figure 10-14. Start Bit Search Example 1
In Figure 10-15, verification sample at RT3 is high. The RT3 sample sets the noise flag. Although the
perceived bit time is misaligned, the data samples RT8, RT9, and RT10 are within the bit time and data
recovery is successful.
Figure 10-15. Start Bit Search Example 2
RESET RT CLOCK
RT1
RT1
RT1
RT1
RT2
RT3
RT4
RT5
RT1
RT1
RT2
RT3
RT4
RT7
RT6
RT5
RT10
RT9
RT8
RT14
RT13
RT12
RT11
RT15
RT16
RT1
RT2
RT3
SAMPLES
RT CLOCK
RT CLOCK COUNT
START BIT
Rx Input Signal
110111100000
LSB
0 0
RESET RT CLOCK
RT1
RT1
RT1
RT1
RT1
RT1
RT2
RT3
RT4
RT5
RT6
RT7
RT8
RT11
RT10
RT9
RT14
RT13
RT12
RT2
RT1
RT16
RT15
RT3
RT4
RT5
RT6
RT7
SAMPLES
RT CLOCK
RT CLOCK COUNT
ACTUAL START BIT
Rx Input Signal
1111110000
LSB
00
PERCEIVED START BIT
Chapter 10 Serial Communications Interface (S12SCIV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 351
In Figure 10-16, a large burst of noise is perceived as the beginning of a start bit, although the test sample
at RT5 is high. The RT5 sample sets the noise flag. Although this is a worst-case misalignment of perceived
bit time, the data samples RT8, RT9, and RT10 are within the bit time and data recovery is successful.
Figure 10-16. Start Bit Search Example 3
Figure 10-17 shows the effect of noise early in the start bit time. Although this noise does not affect proper
synchronization with the start bit time, it does set the noise flag.
Figure 10-17. Start Bit Search Example 4
RESET RT CLOCK
RT1
RT1
RT1
RT1
RT2
RT3
RT4
RT5
RT6
RT7
RT8
RT9
RT10
RT13
RT12
RT11
RT16
RT15
RT14
RT4
RT3
RT2
RT1
RT5
RT6
RT7
RT8
RT9
SAMPLES
RT CLOCK
RT CLOCK COUNT
ACTUAL START BIT
Rx input Signal
101110000
LSB
0
PERCEIVED START BIT
RESET RT CLOCK
RT1
RT1
RT1
RT1
RT1
RT1
RT1
RT1
RT1
RT1
RT2
RT3
RT4
RT7
RT6
RT5
RT10
RT9
RT8
RT14
RT13
RT12
RT11
RT15
RT16
RT1
RT2
RT3
SAMPLES
RT CLOCK
RT CLOCK COUNT
PERCEIVED AND ACTUAL START BIT
Rx Input Signal
11111001
LSB
11 1 1
Chapter 10 Serial Communications Interface (S12SCIV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
352 Freescale Semiconductor
Figure 10-18 shows a burst of noise near the beginning of the start bit that resets the RT clock. The sample
after the reset is low but is not preceded by three high samples that would qualify as a falling edge.
Depending on the timing of the start bit search and on the data, the frame may be missed entirely or it may
set the framing error flag.
Figure 10-18. Start Bit Search Example 5
In Figure 10-19, a noise burst makes the majority of data samples RT8, RT9, and RT10 high. This sets the
noise flag but does not reset the RT clock. In start bits only, the RT8, RT9, and RT10 data samples are
ignored.
Figure 10-19. Start Bit Search Example 6
RESET RT CLOCK
RT1
RT1
RT1
RT1
RT1
RT1
RT1
RT1
RT1
RT1
RT2
RT3
RT4
RT7
RT6
RT5
RT1
RT1
RT1
RT1
RT1
RT1
RT1
RT1
RT1
RT1
RT1
RT1
SAMPLES
RT CLOCK
RT CLOCK COUNT
START BIT
Rx Input Signal
11111010
LSB
11 1 1 1 0000000 0
NO START BIT FOUND
RESET RT CLOCK
RT1
RT1
RT1
RT1
RT1
RT1
RT1
RT1
RT1
RT1
RT2
RT3
RT4
RT7
RT6
RT5
RT10
RT9
RT8
RT14
RT13
RT12
RT11
RT15
RT16
RT1
RT2
RT3
SAMPLES
RT CLOCK
RT CLOCK COUNT
START BIT
Rx Input Signal
11111000
LSB
11 1 1 0 110
Chapter 10 Serial Communications Interface (S12SCIV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 353
10.4.4.4 Framing Errors
If the data recovery logic does not detect a logic 1 where the stop bit should be in an incoming frame, it
sets the framing error flag, FE, in SCI status register 1 (SCISR1). A break character also sets the FE flag
because a break character has no stop bit. The FE flag is set at the same time that the RDRF flag is set.
10.4.4.5 Baud Rate Tolerance
A transmitting device may be operating at a baud rate below or above the receiver baud rate. Accumulated
bit time misalignment can cause one of the three stop bit data samples (RT8, RT9, and RT10) to fall outside
the actual stop bit.A noise error will occur if the RT8, RT9, and RT10 samples are not all the same logical
values. A framing error will occur if the receiver clock is misaligned in such a way that the majority of the
RT8, RT9, and RT10 stop bit samples are a logic zero.
As the receiver samples an incoming frame, it re-synchronizes the RT clock on any valid falling edge
within the frame. Re synchronization within frames will correct a misalignment between transmitter bit
times and receiver bit times.
10.4.4.5.1 Slow Data Tolerance
Figure 10-20 shows how much a slow received frame can be misaligned without causing a noise error or
a framing error. The slow stop bit begins at RT8 instead of RT1 but arrives in time for the stop bit data
samples at RT8, RT9, and RT10.
Figure 10-20. Slow Data
Let’s take RTr as receiver RT clock and RTt as transmitter RT clock.
For an 8-bit data character, it takes the receiver 9 bit times x 16 RTr cycles +7 RTr cycles =151 RTr cycles
to start data sampling of the stop bit.
With the misaligned character shown in Figure 10-20, the receiver counts 151 RTr cycles at the point when
the count of the transmitting device is 9 bit times x 16 RTt cycles = 144 RTt cycles.
The maximum percent difference between the receiver count and the transmitter count of a slow 8-bit data
character with no errors is:
((151 – 144) / 151) x 100 = 4.63%
For a 9-bit data character, it takes the receiver 10 bit times x 16 RTr cycles + 7 RTr cycles = 167 RTr cycles
to start data sampling of the stop bit.
MSB STOP
RT1
RT2
RT3
RT4
RT5
RT6
RT7
RT8
RT9
RT10
RT11
RT12
RT13
RT14
RT15
RT16
DATA
SAMPLES
RECEIVER
RT CLOCK
Chapter 10 Serial Communications Interface (S12SCIV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
354 Freescale Semiconductor
With the misaligned character shown in Figure 10-20, the receiver counts 167 RTr cycles at the point when
the count of the transmitting device is 10 bit times x 16 RTt cycles = 160 RTt cycles.
The maximum percent difference between the receiver count and the transmitter count of a slow 9-bit
character with no errors is:
((167 – 160) / 167) X 100 = 4.19%
10.4.4.5.2 Fast Data Tolerance
Figure 10-21 shows how much a fast received frame can be misaligned. The fast stop bit ends at RT10
instead of RT16 but is still sampled at RT8, RT9, and RT10.
Figure 10-21. Fast Data
For an 8-bit data character, it takes the receiver 9 bit times x 16 RTr cycles + 10 RTr cycles = 154 RTr
cycles to finish data sampling of the stop bit.
With the misaligned character shown in Figure 10-21, the receiver counts 154 RTr cycles at the point when
the count of the transmitting device is 10 bit times x 16 RTt cycles = 160 RTt cycles.
The maximum percent difference between the receiver count and the transmitter count of a fast 8-bit
character with no errors is:
((160 – 154) / 160) x 100 = 3.75%
For a 9-bit data character, it takes the receiver 10 bit times x 16 RTr cycles + 10 RTr cycles = 170 RTr
cycles to finish data sampling of the stop bit.
With the misaligned character shown in Figure 10-21, the receiver counts 170 RTr cycles at the point when
the count of the transmitting device is 11 bit times x 16 RTt cycles = 176 RTt cycles.
The maximum percent difference between the receiver count and the transmitter count of a fast 9-bit
character with no errors is:
((176 – 170) / 176) x 100 = 3.40%
10.4.4.6 Receiver Wakeup
To enable the SCI to ignore transmissions intended only for other receivers in multiple-receiver systems,
the receiver can be put into a standby state. Setting the receiver wakeup bit, RWU, in SCI control register
2 (SCICR2) puts the receiver into standby state during which receiver interrupts are disabled.The SCI will
still load the receive data into the SCIDRH/L registers, but it will not set the RDRF flag.
IDLE OR NEXT FRAMESTOP
RT1
RT2
RT3
RT4
RT5
RT6
RT7
RT8
RT9
RT10
RT11
RT12
RT13
RT14
RT15
RT16
DATA
SAMPLES
RECEIVER
RT CLOCK
Chapter 10 Serial Communications Interface (S12SCIV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 355
The transmitting device can address messages to selected receivers by including addressing information
in the initial frame or frames of each message.
The WAKE bit in SCI control register 1 (SCICR1) determines how the SCI is brought out of the standby
state to process an incoming message. The WAKE bit enables either idle line wakeup or address mark
wakeup.
10.4.4.6.1 Idle Input Line Wakeup (WAKE = 0)
In this wakeup method, an idle condition on the Rx Input signal clears the RWU bit and wakes up the SCI.
The initial frame or frames of every message contain addressing information. All receivers evaluate the
addressing information, and receivers for which the message is addressed process the frames that follow.
Any receiver for which a message is not addressed can set its RWU bit and return to the standby state. The
RWU bit remains set and the receiver remains on standby until another idle character appears on the Rx
Input signal.
Idle line wakeup requires that messages be separated by at least one idle character and that no message
contains idle characters.
The idle character that wakes a receiver does not set the receiver idle bit, IDLE, or the receive data register
full flag, RDRF.
The idle line type bit, ILT, determines whether the receiver begins counting logic 1s as idle character bits
after the start bit or after the stop bit. ILT is in SCI control register 1 (SCICR1).
10.4.4.6.2 Address Mark Wakeup (WAKE = 1)
In this wakeup method, a logic 1 in the most significant bit (msb) position of a frame clears the RWU bit
and wakes up the SCI. The logic 1 in the msb position marks a frame as an address frame that contains
addressing information. All receivers evaluate the addressing information, and the receivers for which the
message is addressed process the frames that follow.Any receiver for which a message is not addressed can
set its RWU bit and return to the standby state. The RWU bit remains set and the receiver remains on
standby until another address frame appears on the Rx Input signal.
The logic 1 msb of an address frame clears the receiver’s RWU bit before the stop bit is received and sets
the RDRF flag.
Address mark wakeup allows messages to contain idle characters but requires that the msb be reserved for
use in address frames.{sci_wake}
NOTE
With the WAKE bit clear, setting the RWU bit after the Rx Input signal has
been idle can cause the receiver to wake up immediately.
Chapter 10 Serial Communications Interface (S12SCIV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
356 Freescale Semiconductor
10.4.5 Single-Wire Operation
Normally, the SCI uses two pins for transmitting and receiving. In single-wire operation, the RXD pin is
disconnected from the SCI. The SCI uses the TXD pin for both receiving and transmitting.
Figure 10-22. Single-Wire Operation (LOOPS = 1, RSRC = 1)
Enable single-wire operation by setting the LOOPS bit and the receiver source bit, RSRC, in SCI control
register 1 (SCICR1). Setting the LOOPS bit disables the path from the Rx Input signal to the receiver.
Setting the RSRC bit connects the receiver input to the output of the TXD pin driver. Both the transmitter
and receiver must be enabled (TE = 1 and RE = 1).The TXDIR bit (SCISR2[1]) determines whether the
TXD pin is going to be used as an input (TXDIR = 0) or an output (TXDIR = 1) in this mode of operation.
10.4.6 Loop Operation
In loop operation the transmitter output goes to the receiver input. The Rx Input signal is disconnected
from the SCI
.
Figure 10-23. Loop Operation (LOOPS = 1, RSRC = 0)
Enable loop operation by setting the LOOPS bit and clearing the RSRC bit in SCI control register 1
(SCICR1). Setting the LOOPS bit disables the path from the Rx Input signal to the receiver. Clearing the
RSRC bit connects the transmitter output to the receiver input. Both the transmitter and receiver must be
enabled (TE = 1 and RE = 1).
10.5 Initialization Information
10.5.1 Reset Initialization
The reset state of each individual bit is listed in Section 10.3, “Memory Map and Registers” which details
the registers and their bit fields. All special functions or modes which are initialized during or just
following reset are described within this section.
RXD
TRANSMITTER
RECEIVER
Tx OUTPUT SIGNAL
Tx INPUT SIGNAL
RXD
TRANSMITTER
RECEIVER
Tx OUTPUT SIGNAL
Chapter 10 Serial Communications Interface (S12SCIV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 357
10.5.2 Interrupt Operation
10.5.2.1 System Level Interrupt Sources
There are five interrupt sources that can generate an SCI interrupt in to the CPU. They are listed in
Table 10-14.
Table 10-14. SCI Interrupt Source
Interrupt Source Flag Local Enable
Transmitter TDRE TIE
Transmitter TC TCIE
Receiver RDRF RIE
OR
Receiver IDLE ILIE
Chapter 10 Serial Communications Interface (S12SCIV2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
358 Freescale Semiconductor
10.5.2.2 Interrupt Descriptions
The SCI only originates interrupt requests. The following is a description of how the SCI makes a request
and how the MCU should acknowledge that request. The interrupt vector offset and interrupt number are
chip dependent. The SCI only has a single interrupt line (SCI Interrupt Signal, active high operation) and
all the following interrupts, when generated, are ORed together and issued through that port.
10.5.2.2.1 TDRE Description
The TDRE interrupt is set high by the SCI when the transmit shift register receives a byte from the SCI
data register. A TDRE interrupt indicates that the transmit data register (SCIDRH/L) is empty and that a
new byte can be written to the SCIDRH/L for transmission.Clear TDRE by reading SCI status register 1
with TDRE set and then writing to SCI data register low (SCIDRL).
10.5.2.2.2 TC Description
The TC interrupt is set by the SCI when a transmission has been completed.A TC interrupt indicates that
there is no transmission in progress. TC is set high when the TDRE flag is set and no data, preamble, or
break character is being transmitted. When TC is set, the TXD pin becomes idle (logic 1). Clear TC by
reading SCI status register 1 (SCISR1) with TC set and then writing to SCI data register low (SCIDRL).TC
is cleared automatically when data, preamble, or break is queued and ready to be sent.
10.5.2.2.3 RDRF Description
The RDRF interrupt is set when the data in the receive shift register transfers to the SCI data register. A
RDRF interrupt indicates that the received data has been transferred to the SCI data register and that the
byte can now be read by the MCU. The RDRF interrupt is cleared by reading the SCI status register one
(SCISR1) and then reading SCI data register low (SCIDRL).
10.5.2.2.4 OR Description
The OR interrupt is set when software fails to read the SCI data register before the receive shift register
receives the next frame. The newly acquired data in the shift register will be lost in this case, but the data
already in the SCI data registers is not affected. The OR interrupt is cleared by reading the SCI status
register one (SCISR1) and then reading SCI data register low (SCIDRL).
10.5.2.3 IDLE Description
The IDLE interrupt is set when 10 consecutive logic 1s (if M = 0) or 11 consecutive logic 1s (if M = 1)
appear on the receiver input. Once the IDLE is cleared, a valid frame must again set the RDRF flag before
an idle condition can set the IDLE flag. Clear IDLE by reading SCI status register 1 (SCISR1) with IDLE
set and then reading SCI data register low (SCIDRL).
10.5.3 Recovery from Wait Mode
The SCI interrupt request can be used to bring the CPU out of wait mode.
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 359
Chapter 11
Serial Peripheral Interface (SPIV3) Block Description
11.1 Introduction
The SPI module allows a duplex, synchronous, serial communication between the MCU and peripheral
devices. Software can poll the SPI status flags or the SPI operation can be interrupt driven.
11.1.1 Features
The SPIV3 includes these distinctive features:
Master mode and slave mode
Bidirectional mode
Slave select output
Mode fault error flag with CPU interrupt capability
Double-buffered data register
Serial clock with programmable polarity and phase
Control of SPI operation during wait mode
11.1.2 Modes of Operation
The SPI functions in three modes, run, wait, and stop.
Run Mode
This is the basic mode of operation.
Wait Mode
SPI operation in wait mode is a configurable low power mode, controlled by the SPISWAI bit
located in the SPICR2 register. In wait mode, if the SPISWAI bit is clear, the SPI operates like in
Run Mode. If the SPISWAI bit is set, the SPI goes into a power conservative state, with the SPI
clock generation turned off. If the SPI is configured as a master, any transmission in progress stops,
but is resumed after CPU goes into Run Mode. If the SPI is configured as a slave, reception and
transmission of a byte continues, so that the slave stays synchronized to the master.
Stop Mode
The SPI is inactive in stop mode for reduced power consumption. If the SPI is configured as a
master, any transmission in progress stops, but is resumed after CPU goes into run mode. If the SPI
is configured as a slave, reception and transmission of a byte continues, so that the slave stays
synchronized to the master.
This is a high level description only, detailed descriptions of operating modes are contained in
Section 11.4, “Functional Description.
Chapter 11 Serial Peripheral Interface (SPIV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
360 Freescale Semiconductor
11.1.3 Block Diagram
Figure 11-1 gives an overview on the SPI architecture. The main parts of the SPI are status, control, and
data registers, shifter logic, baud rate generator, master/slave control logic, and port control logic.
Figure 11-1. SPI Block Diagram
11.2 External Signal Description
This section lists the name and description of all ports including inputs and outputs that do, or may, connect
off chip. The SPIV3 module has a total of four external pins.
11.2.1 MOSI — Master Out/Slave In Pin
This pin is used to transmit data out of the SPI module when it is configured as a master and receive data
when it is configured as slave.
SPI Control Register 1
SPI Control Register 2
SPI Baud Rate Register
SPI Status Register
SPI Data Register
Shifter
Port
Control
Logic
MOSI
SCK
Interrupt Control
SPI
MSB LSB
LSBFE=1 LSBFE=0
LSBFE=0 LSBFE=1
data in
LSBFE=1
LSBFE=0
data out
8
8
Baud Rate Generator
Prescaler
Bus Clock
Counter
Clock Select
SPPR 33
SPR
Baud Rate
Phase +
Polarity
Control
Master
Slave
SCK in
SCK out
Master Baud Rate
Slave Baud Rate
Phase +
Polarity
Control
Control
Control CPOL CPHA
2
BIDIROE
SPC0
2
MODFSPIF SPTEF
SPI
Request
Interrupt
SS
Shift
Clock Sample
Clock
Chapter 11 Serial Peripheral Interface (SPIV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 361
11.2.2 MISO — Master In/Slave Out Pin
This pin is used to transmit data out of the SPI module when it is configured as a slave and receive data
when it is configured as master.
11.2.3 SS — Slave Select Pin
This pin is used to output the select signal from the SPI module to another peripheral with which a data
transfer is to take place when its configured as a master and its used as an input to receive the slave select
signal when the SPI is configured as slave.
11.2.4 SCK — Serial Clock Pin
This pin is used to output the clock with respect to which the SPI transfers data or receive clock in case of
slave.
11.3 Memory Map and Register Definition
This section provides a detailed description of address space and registers used by the SPI.
The memory map for the SPIV3 is given below in Table 11-1. The address listed for each register is the
sum of a base address and an address offset. The base address is defined at the SoC level and the address
offset is defined at the module level. Reads from the reserved bits return zeros and writes to the reserved
bits have no effect.
11.3.1 Module Memory Map
Table 11-1. SPIV3 Memory Map
Address Use Access
0x0000 SPI Control Register 1 (SPICR1) R/W
0x0001 SPI Control Register 2 (SPICR2) R/W1
1Certain bits are non-writable.
0x0002 SPI Baud Rate Register (SPIBR) R/W1
0x0003 SPI Status Register (SPISR) R2
2Writes to this register are ignored.
0x0004 Reserved 2,3
3Reading from this register returns all zeros.
0x0005 SPI Data Register (SPIDR) R/W
0x0006 Reserved 2,3
0x0007 Reserved 2,3
Chapter 11 Serial Peripheral Interface (SPIV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
362 Freescale Semiconductor
11.3.2 Register Descriptions
This section consists of register descriptions in address order. Each description includes a standard register
diagram with an associated figure number. Details of register bit and field function follow the register
diagrams, in bit order.
11.3.2.1 SPI Control Register 1 (SPICR1)
Read: anytime
Write: anytime
Name 7 6 5 4 3 2 1 0
0x0000
SPICR1 RSPIE SPE SPTIE MSTR CPOL CPHA SSOE LSBFE
W
0x0001
SPICR2 R0 0 0MODFEN BIDIROE 0SPISWAI SPC0
W
0x0002
SPIBR R0 SPPR2 SPPR1 SPPR0 0SPR2 SPR1 SPR0
W
0x0003
SPISR R SPIF 0 SPTEF MODF 0 0 0 0
W
0x0004
Reserved R
W
0x0005
SPIDR RBit 7 6 5 4 3 2 2 Bit 0
W
0x0006
Reserved R
W
0x0007
Reserved R
W
= Unimplemented or Reserved
Figure 11-2. SPI Register Summary
Module Base 0x0000
76543210
RSPIE SPE SPTIE MSTR CPOL CPHA SSOE LSBFE
W
Reset 0 0 0 00100
Figure 11-3. SPI Control Register 1 (SPICR1)
Chapter 11 Serial Peripheral Interface (SPIV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 363
Table 11-2. SPICR1 Field Descriptions
Field Description
7
SPIE SPI Interrupt Enable Bit — This bit enables SPI interrupt requests, if SPIF or MODF status flag is set.
0 SPI interrupts disabled.
1 SPI interrupts enabled.
6
SPE SPI System Enable Bit — This bit enables the SPI system and dedicates the SPI port pins to SPI system
functions. If SPE is cleared, SPI is disabled and forced into idle state, status bits in SPISR register are reset.
0 SPI disabled (lower power consumption).
1 SPI enabled, port pins are dedicated to SPI functions.
5
SPTIE SPI Transmit Interrupt Enable — This bit enables SPI interrupt requests, if SPTEF flag is set.
0 SPTEF interrupt disabled.
1 SPTEF interrupt enabled.
4
MSTR SPI Master/Slave Mode Select Bit — This bit selects, if the SPI operates in master or slave mode. Switching
the SPI from master to slave or vice versa forces the SPI system into idle state.
0 SPI is in slave mode
1 SPI is in master mode
3
CPOL SPI Clock Polarity Bit This bit selects an inverted or non-inverted SPI clock. To transmit data between SPI
modules, the SPI modules must have identical CPOL values. In master mode, a change of this bit will abort a
transmission in progress and force the SPI system into idle state.
0 Active-high clocks selected. In idle state SCK is low.
1 Active-low clocks selected. In idle state SCK is high.
2
CPHA SPI Clock Phase Bit This bit is used to select the SPI clock format. In master mode, a change of this bit will
abort a transmission in progress and force the SPI system into idle state.
0 Sampling of data occurs at odd edges (1,3,5,...,15) of the SCK clock
1 Sampling of data occurs at even edges (2,4,6,...,16) of the SCK clock
1
SSOE Slave Select Output Enable — The SS output feature is enabled only in master mode, if MODFEN is set, by
asserting the SSOE as shown in Table 11-3. In master mode, a change of this bit will abort a transmission in
progress and force the SPI system into idle state.
0
LSBFE LSB-First Enable — This bit does not affect the position of the MSB and LSB in the data register. Reads and
writes of the data register always have the MSB in bit 7. In master mode, a change of this bit will abort a
transmission in progress and force the SPI system into idle state.
0 Data is transferred most significant bit first.
1 Data is transferred least significant bit first.
Table 11-3. SS Input / Output Selection
MODFEN SSOE Master Mode Slave Mode
00 SS not used by SPI SS input
01 SS not used by SPI SS input
10
SS input with MODF feature SS input
11SS is slave select output SS input
Chapter 11 Serial Peripheral Interface (SPIV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
364 Freescale Semiconductor
11.3.2.2 SPI Control Register 2 (SPICR2)
Read: anytime
Write: anytime; writes to the reserved bits have no effect
Module Base 0x0001
76543210
R000
MODFEN BIDIROE 0SPISWAI SPC0
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 11-4. SPI Control Register 2 (SPICR2)
Table 11-4. SPICR2 Field Descriptions
Field Description
4
MODFEN Mode Fault Enable Bit — This bit allows the MODF failure being detected. If the SPI is in master mode and
MODFEN is cleared, then the SS port pin is not used by the SPI. In slave mode, the SS is available only as an
input regardless of the value of MODFEN. For an overview on the impact of the MODFEN bit on the SS port pin
configuration refer to Table 11-3. In master mode, a change of this bit will abort a transmission in progress and
force the SPI system into idle state.
0SS port pin is not used by the SPI
1SS port pin with MODF feature
3
BIDIROE Output Enable in the Bidirectional Mode of Operation This bit controls the MOSI and MISO output buffer
of the SPI, when in bidirectional mode of operation (SPC0 is set). In master mode this bit controls the output
buffer of the MOSI port, in slave mode it controls the output buffer of the MISO port. In master mode, with SPC0
set, a change of this bit will abort a transmission in progress and force the SPI into idle state.
0 Output buffer disabled
1 Output buffer enabled
1
SPISWAI SPI Stop in Wait Mode Bit — This bit is used for power conservation while in wait mode.
0 SPI clock operates normally in wait mode
1 Stop SPI clock generation when in wait mode
0
SPC0 Serial Pin Control Bit 0 — This bit enables bidirectional pin configurations as shown in Table 11-5. In master
mode, a change of this bit will abort a transmission in progress and force the SPI system into idle state
Table 11-5. Bidirectional Pin Configurations
Pin Mode SPC0 BIDIROE MISO MOSI
Master Mode of Operation
Normal 0 X Master In Master Out
Bidirectional 1 0 MISO not used by SPI Master In
1 Master I/O
Slave Mode of Operation
Normal 0 X Slave Out Slave In
Chapter 11 Serial Peripheral Interface (SPIV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 365
11.3.2.3 SPI Baud Rate Register (SPIBR)
Read: anytime
Write: anytime; writes to the reserved bits have no effect
The baud rate divisor equation is as follows:
The baud rate can be calculated with the following equation:
Bidirectional 1 0 Slave In MOSI not used by SPI
1 Slave I/O
Module Base 0x0002
76543210
R0 SPPR2 SPPR1 SPPR0 0SPR2 SPR1 SPR0
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 11-5. SPI Baud Rate Register (SPIBR)
Table 11-6. SPIBR Field Descriptions
Field Description
6:4
SPPR[2:0] SPI Baud Rate Preselection Bits — These bits specify the SPI baud rates as shown in Table 11-7. In master
mode, a change of these bits will abort a transmission in progress and force the SPI system into idle state.
2:0
SPR[2:0} SPI Baud Rate Selection Bits These bits specify the SPI baud ratesasshown in Table 11-7.In master mode,
a change of these bits will abort a transmission in progress and force the SPI system into idle state.
Table 11-5. Bidirectional Pin Configurations (continued)
Pin Mode SPC0 BIDIROE MISO MOSI
BaudRateDivisor SPPR 1+()2SPR 1+()
=
Baud Rate BusClock BaudRateDivisor=
Chapter 11 Serial Peripheral Interface (SPIV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
366 Freescale Semiconductor
Table 11-7. Example SPI Baud Rate Selection (25 MHz Bus Clock)
SPPR2 SPPR1 SPPR0 SPR2 SPR1 SPR0 Baud Rate
Divisor Baud Rate
000000212.5 MHz
00000146.25 MHz
00001083.125 MHz
000011161.5625 MHz
00010032781.25 kHz
00010164390.63 kHz
000110128195.31 kHz
00011125697.66 kHz
00100046.25 MHz
00100183.125 MHz
001010161.5625 MHz
00101132781.25 kHz
00110064390.63 kHz
001101128195.31 kHz
00111025697.66 kHz
00111151248.83 kHz
01000064.16667 MHz
010001122.08333 MHz
010010241.04167 MHz
01001148520.83 kHz
01010096260.42 kHz
010101192130.21 kHz
01011038465.10 kHz
01011176832.55 kHz
01100083.125 MHz
011001161.5625 MHz
01101032781.25 kHz
01101164390.63 kHz
011100128195.31 kHz
01110125697.66 kHz
01111051248.83 kHz
0111111024 24.41 kHz
100000102.5 MHz
100001201.25 MHz
10001040625 kHz
10001180312.5 kHz
100100160156.25 kHz
10010132078.13 kHz
10011064039.06 kHz
Chapter 11 Serial Peripheral Interface (SPIV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 367
NOTE
In slave mode of SPI S-clock speed DIV2 is not supported.
1001111280 19.53 kHz
101000122.08333 MHz
101001241.04167 MHz
10101048520.83 kHz
10101196260.42 kHz
101100192130.21 kHz
10110138465.10 kHz
10111076832.55 kHz
1011111536 16.28 kHz
110000141.78571 MHz
11000128892.86 kHz
11001056446.43 kHz
110011112223.21 kHz
110100224111.61 kHz
11010144855.80 kHz
11011089627.90 kHz
1101111792 13.95 kHz
111000161.5625 MHz
11100132781.25 kHz
11101064390.63 kHz
111011128195.31 kHz
11110025697.66 kHz
11110151248.83 kHz
1111101024 24.41 kHz
1111112048 12.21 kHz
Table 11-7. Example SPI Baud Rate Selection (25 MHz Bus Clock) (continued)
SPPR2 SPPR1 SPPR0 SPR2 SPR1 SPR0 Baud Rate
Divisor Baud Rate
Chapter 11 Serial Peripheral Interface (SPIV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
368 Freescale Semiconductor
11.3.2.4 SPI Status Register (SPISR)
Read: anytime
Write: has no effect
11.3.2.5 SPI Data Register (SPIDR)
Read: anytime; normally read only after SPIF is set
Module Base 0x0003
76543210
R SPIF 0 SPTEF MODF 0000
W
Reset 0 0 1 00000
= Unimplemented or Reserved
Figure 11-6. SPI Status Register (SPISR)
Table 11-8. SPISR Field Descriptions
Field Description
7
SPIF SPIF Interrupt Flag This bit is set after a received data byte has been transferred into the SPI Data Register.
This bit is cleared by reading the SPISR register (with SPIF set) followed by a read access to the SPI Data
Register.
0 Transfer not yet complete
1 New data copied to SPIDR
5
SPTEF SPI Transmit Empty Interrupt Flag If set, this bit indicates that the transmit data register is empty. To clear
this bit and place data into the transmit data register, SPISR has to be read with SPTEF = 1, followed by a write
to SPIDR. Any write to the SPI Data Register without reading SPTEF = 1, is effectively ignored.
0 SPI Data register not empty
1 SPI Data register empty
4
MODF Mode Fault Flag This bit is set if the SS input becomes low while the SPI is configured as a master and mode
fault detection is enabled, MODFEN bit of SPICR2 register is set. Refer to MODFEN bit description in
Section 11.3.2.2,“SPI Control Register 2 (SPICR2).Theflag is cleared automatically bya read of the SPI Status
Register (with MODF set) followed by a write to the SPI Control Register 1.
0 Mode fault has not occurred.
1 Mode fault has occurred.
Module Base 0x0005
76543210
RBit 7 6 5 4322Bit 0
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 11-7. SPI Data Register (SPIDR)
Chapter 11 Serial Peripheral Interface (SPIV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 369
Write: anytime
The SPI Data Register is both the input and output register for SPI data. A write to this register allows a
data byte to be queued and transmitted. For a SPI configured as a master, a queued data byte is transmitted
immediately after the previous transmission has completed. The SPI Transmitter Empty Flag SPTEF in
the SPISR register indicates when the SPI Data Register is ready to accept new data.
Reading the data can occur anytime from after the SPIF is set to before the end of the next transfer. If the
SPIF is not serviced by the end of the successive transfers, those data bytes are lost and the data within the
SPIDR retains the first byte until SPIF is serviced.
11.4 Functional Description
The SPI module allows a duplex, synchronous, serial communication between the MCU and peripheral
devices. Software can poll the SPI status flags or SPI operation can be interrupt driven.
The SPI system is enabled by setting the SPI enable (SPE) bit in SPI Control Register 1. While SPE bit is
set, the four associated SPI port pins are dedicated to the SPI function as:
Slave select (SS)
Serial clock (SCK)
Master out/slave in (MOSI)
Master in/slave out (MISO)
The main element of the SPI system is the SPI Data Register. The 8-bit data register in the master and the
8-bit data register in the slave are linked by the MOSI and MISO pins to form a distributed 16-bit register.
When a data transfer operation is performed, this 16-bit register is serially shifted eight bit positions by the
S-clock from the master, so data is exchanged between the master and the slave. Data written to the master
SPI Data Register becomes the output data for the slave, and data read from the master SPI Data Register
after a transfer operation is the input data from the slave.
A read of SPISR with SPTEF = 1 followed by a write to SPIDR puts data into the transmit data register.
When a transfer is complete, received data is moved into the receive data register. Data may be read from
this double-buffered system any time before the next transfer has completed. This 8-bit data register acts
as the SPI receive data register for reads and as the SPI transmit data register for writes. A single SPI
register address is used for reading data from the read data buffer and for writing data to the transmit data
register.
The clock phase control bit (CPHA) and a clock polarity control bit (CPOL) in the SPI Control Register 1
(SPICR1) select one of four possible clock formats to be used by the SPI system. The CPOL bit simply
selects a non-inverted or inverted clock. The CPHA bit is used to accommodate two fundamentally
different protocols by sampling data on odd numbered SCK edges or on even numbered SCK edges (see
Section 11.4.3, “Transmission Formats”).
The SPI can be configured to operate as a master or as a slave. When the MSTR bit in SPI Control
Register1 is set, master mode is selected, when the MSTR bit is clear, slave mode is selected.
Chapter 11 Serial Peripheral Interface (SPIV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
370 Freescale Semiconductor
11.4.1 Master Mode
The SPI operates in master mode when the MSTR bit is set. Only a master SPI module can initiate
transmissions. A transmission begins by writing to the master SPI Data Register. If the shift register is
empty, the byte immediately transfers to the shift register. The byte begins shifting out on the MOSI pin
under the control of the serial clock.
S-clock
The SPR2, SPR1, and SPR0 baud rate selection bits in conjunction with the SPPR2, SPPR1, and
SPPR0 baud rate preselection bits in the SPI Baud Rate register control the baud rate generator and
determine the speed of the transmission. The SCK pin is the SPI clock output. Through the SCK
pin, the baud rate generator of the master controls the shift register of the slave peripheral.
MOSI and MISO Pins
In master mode, the function of the serial data output pin (MOSI) and the serial data input pin
(MISO) is determined by the SPC0 and BIDIROE control bits.
SS Pin
If MODFEN and SSOE bit are set, the SS pin is configured as slave select output. The SS output
becomes low during each transmission and is high when the SPI is in idle state.
If MODFEN is set and SSOE is cleared, the SS pin is configured as input for detecting mode fault
error. If the SS input becomes low this indicates a mode fault error where another master tries to
drive the MOSI and SCK lines. In this case, the SPI immediately switches to slave mode, by
clearing the MSTR bit and also disables the slave output buffer MISO (or SISO in bidirectional
mode). So the result is that all outputs are disabled and SCK, MOSI and MISO are inputs. If a
transmission is in progress when the mode fault occurs, the transmission is aborted and the SPI is
forced into idle state.
This mode fault error also sets the mode fault (MODF) flag in the SPI Status Register (SPISR). If the SPI
interrupt enable bit (SPIE) is set when the MODF flag gets set, then an SPI interrupt sequence is also
requested.
When a write to the SPI Data Register in the master occurs, there is a half SCK-cycle delay. After the delay,
SCK is started within the master. The rest of the transfer operation differs slightly, depending on the clock
format specified by the SPI clock phase bit, CPHA, in SPI Control Register 1 (see Section 11.4.3,
“Transmission Formats”).
NOTE
A change of the bits CPOL, CPHA, SSOE, LSBFE, MODFEN, SPC0,
BIDIROE with SPC0 set, SPPR2–SPPR0 and SPR2–SPR0 in master mode
will abort a transmission in progress and force the SPI into idle state. The
remote slave cannot detect this, therefore the master has to ensure that the
remote slave is set back to idle state.
Chapter 11 Serial Peripheral Interface (SPIV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 371
11.4.2 Slave Mode
The SPI operates in slave mode when the MSTR bit in SPI Control Register1 is clear.
SCK Clock
In slave mode, SCK is the SPI clock input from the master.
MISO and MOSI Pins
In slave mode, the function of the serial data output pin (MISO) and serial data input pin (MOSI)
is determined by the SPC0 bit and BIDIROE bit in SPI Control Register 2.
SS Pin
The SS pin is the slave select input. Before a data transmission occurs, the SS pin of the slave SPI
must be low. SS must remain low until the transmission is complete. If SS goes high, the SPI is
forced into idle state.
The SS input also controls the serial data output pin, if SS is high (not selected), the serial data
output pin is high impedance, and, if SS is low the first bit in the SPI Data Register is driven out of
the serial data output pin. Also, if the slave is not selected (SS is high), then the SCK input is
ignored and no internal shifting of the SPI shift register takes place.
Although the SPI is capable of duplex operation, some SPI peripherals are capable of only receiving SPI
data in a slave mode. For these simpler devices, there is no serial data out pin.
NOTE
When peripherals with duplex capability are used, take care not to
simultaneously enable two receivers whose serial outputs drive the same
system slave’s serial data output line.
As long as no more than one slave device drives the system slave’s serial data output line, it is possible for
several slaves to receive the same transmission from a master, although the master would not receive return
information from all of the receiving slaves.
If the CPHA bit in SPI Control Register 1 is clear, odd numbered edges on the SCK input cause the data
at the serial data input pin to be latched. Even numbered edges cause the value previously latched from the
serial data input pin to shift into the LSB or MSB of the SPI shift register, depending on the LSBFE bit.
If the CPHA bit is set, even numbered edges on the SCK input cause the data at the serial data input pin to
be latched. Odd numbered edges cause the value previously latched from the serial data input pin to shift
into the LSB or MSB of the SPI shift register, depending on the LSBFE bit.
When CPHA is set, the first edge is used to get the first data bit onto the serial data output pin. When CPHA
is clear and the SS input is low (slave selected), the first bit of the SPI data is driven out of the serial data
output pin. After the eighth shift, the transfer is considered complete and the received data is transferred
into the SPI Data Register. To indicate transfer is complete, the SPIF flag in the SPI Status Register is set.
NOTE
A change of the bits CPOL, CPHA, SSOE, LSBFE, MODFEN, SPC0 and
BIDIROE with SPC0 set in slave mode will corrupt a transmission in
progress and has to be avoided.
Chapter 11 Serial Peripheral Interface (SPIV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
372 Freescale Semiconductor
11.4.3 Transmission Formats
During an SPI transmission, data is transmitted (shifted out serially) and received (shifted in serially)
simultaneously. The serial clock (SCK) synchronizes shifting and sampling of the information on the two
serial data lines. A slave select line allows selection of an individual slave SPI device, slave devices that
are not selected do not interfere with SPI bus activities. Optionally, on a master SPI device, the slave select
line can be used to indicate multiple-master bus contention.
Figure 11-8. Master/Slave Transfer Block Diagram
11.4.3.1 Clock Phase and Polarity Controls
Using two bits in the SPI Control Register1, software selects one of four combinations of serial clock phase
and polarity.
The CPOL clock polarity control bit specifies an active high or low clock and has no significant effect on
the transmission format.
The CPHA clock phase control bit selects one of two fundamentally different transmission formats.
Clock phase and polarity should be identical for the master SPI device and the communicating slave
device. In some cases, the phase and polarity are changed between transmissions to allow a master device
to communicate with peripheral slaves having different requirements.
11.4.3.2 CPHA = 0 Transfer Format
The first edge on the SCK line is used to clock the first data bit of the slave into the master and the first
data bit of the master into the slave. In some peripherals, the first bit of the slave’s data is available at the
slave’s data out pin as soon as the slave is selected. In this format, the first SCK edge is issued a half cycle
after SS has become low.
A half SCK cycle later, the second edge appears on the SCK line. When this second edge occurs, the value
previously latched from the serial data input pin is shifted into the LSB or MSB of the shift register,
depending on LSBFE bit.
After this second edge, the next bit of the SPI master data is transmitted out of the serial data output pin of
the master to the serial input pin on the slave. This process continues for a total of 16 edges on the SCK
line, with data being latched on odd numbered edges and shifted on even numbered edges.
SHIFT REGISTER
SHIFT REGISTER
BAUD RATE
GENERATOR
MASTER SPI SLAVE SPI
MOSI MOSI
MISO MISO
SCK SCK
SS SS
VDD
Chapter 11 Serial Peripheral Interface (SPIV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 373
Data reception is double buffered. Data is shifted serially into the SPI shift register during the transfer and
is transferred to the parallel SPI Data Register after the last bit is shifted in.
After the 16th (last) SCK edge:
Data that was previously in the master SPI Data Register should now be in the slave data register
and the data that was in the slave data register should be in the master.
The SPIF flag in the SPI Status Register is set indicating that the transfer is complete.
Figure 11-9 is a timing diagram of an SPI transfer where CPHA = 0. SCK waveforms are shown for
CPOL = 0 and CPOL = 1. The diagram may be interpreted as a master or slave timing diagram because
the SCK, MISO, and MOSI pins are connected directly between the master and the slave. The MISO signal
is the output from the slave and the MOSI signal is the output from the master. The SS pin of the master
must be either high or reconfigured as a general-purpose output not affecting the SPI.
Figure 11-9. SPI Clock Format 0 (CPHA = 0)
In slave mode, if the SS line is not deasserted between the successive transmissions then the content of the
SPI Data Register is not transmitted, instead the last received byte is transmitted. If the SS line is deasserted
for at least minimum idle time (half SCK cycle) between successive transmissions then the content of the
SPI Data Register is transmitted.
tL
Begin End
SCK (CPOL = 0)
SAMPLE I
CHANGE O
SEL SS (O)
Transfer
SCK (CPOL = 1)
MSB first (LSBFE = 0):
LSB first (LSBFE = 1): MSB
LSB LSB
MSB
Bit 5
Bit 2
Bit 6
Bit 1 Bit 4
Bit 3 Bit 3
Bit 4 Bit 2
Bit 5 Bit 1
Bit 6
CHANGE O
SEL SS (I)
MOSI pin
MISO pin
Master only
MOSI/MISO
tT
If next transfer begins here
for tT, tl, tL
Minimum 1/2 SCK
tI tL
tL = Minimum leading time before the first SCK edge
tT = Minimum trailing time after the last SCK edge
tI = Minimum idling time between transfers (minimum SS high time)
tL, tT, and tI are guaranteed for the master mode and required for the slave mode.
1 234 56 78910111213141516
SCK Edge Nr.
End of Idle State Begin of Idle State
Chapter 11 Serial Peripheral Interface (SPIV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
374 Freescale Semiconductor
In master mode, with slave select output enabled the SS line is always deasserted and reasserted between
successive transfers for at least minimum idle time.
11.4.3.3 CPHA = 1 Transfer Format
Some peripherals require the first SCK edge before the first data bit becomes available at the data out pin,
the second edge clocks data into the system. In this format, the first SCK edge is issued by setting the
CPHA bit at the beginning of the 8-cycle transfer operation.
The first edge of SCK occurs immediately after the half SCK clock cycle synchronization delay. This first
edge commands the slave to transfer its first data bit to the serial data input pin of the master.
A half SCK cycle later, the second edge appears on the SCK pin. This is the latching edge for both the
master and slave.
When the third edge occurs, the value previously latched from the serial data input pin is shifted into the
LSB or MSB of the SPI shift register, depending on LSBFE bit. After this edge, the next bit of the master
data is coupled out of the serial data output pin of the master to the serial input pin on the slave.
This process continues for a total of 16 edges on the SCK line with data being latched on even numbered
edges and shifting taking place on odd numbered edges.
Data reception is double buffered, data is serially shifted into the SPI shift register during the transfer and
is transferred to the parallel SPI Data Register after the last bit is shifted in.
After the 16th SCK edge:
Data that was previously in the SPI Data Register of the master is now in the data register of the
slave, and data that was in the data register of the slave is in the master.
The SPIF flag bit in SPISR is set indicating that the transfer is complete.
Figure 11-10 shows two clocking variations for CPHA = 1. The diagram may be interpreted as a master or
slave timing diagram because the SCK, MISO, and MOSI pins are connected directly between the master
and the slave. The MISO signal is the output from the slave, and the MOSI signal is the output from the
master. The SS line is the slave select input to the slave. The SS pin of the master must be either high or
reconfigured as a general-purpose output not affecting the SPI.
The SS line can remain active low between successive transfers (can be tied low at all times). This format
is sometimes preferred in systems having a single fixed master and a single slave that drive the MISO data
line.
Back-to-back transfers in master mode
In master mode, if a transmission has completed and a new data byte is available in the SPI Data Register,
this byte is send out immediately without a trailing and minimum idle time.
The SPI interrupt request flag (SPIF) is common to both the master and slave modes. SPIF gets set one
half SCK cycle after the last SCK edge.
Chapter 11 Serial Peripheral Interface (SPIV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 375
Figure 11-10. SPI Clock Format 1 (CPHA = 1)
11.4.4 SPI Baud Rate Generation
Baud rate generation consists of a series of divider stages. Six bits in the SPI Baud Rate register (SPPR2,
SPPR1, SPPR0, SPR2, SPR1, and SPR0) determine the divisor to the SPI module clock which results in
the SPI baud rate.
The SPI clock rate is determined by the product of the value in the baud rate preselection bits
(SPPR2–SPPR0) and the value in the baud rate selection bits (SPR2–SPR0). The module clock divisor
equation is shown in Figure 11-11
When all bits are clear (the default condition), the SPI module clock is divided by 2. When the selection
bits (SPR2–SPR0) are 001 and the preselection bits (SPPR2–SPPR0) are 000, the module clock divisor
becomes 4. When the selection bits are 010, the module clock divisor becomes 8 etc.
When the preselection bits are 001, the divisor determined by the selection bits is multiplied by 2. When
the preselection bits are 010, the divisor is multiplied by 3, etc. See Table 11-7 for baud rate calculations
for all bit conditions, based on a 25-MHz bus clock. The two sets of selects allows the clock to be divided
by a non-power of two to achieve other baud rates such as divide by 6, divide by 10, etc.
tL tT
for tT, tl, tL
Minimum 1/2 SCK
tI tL
If next transfer begins here
Begin End
SCK (CPOL = 0)
SAMPLE I
CHANGE O
SEL SS (O)
Transfer
SCK (CPOL = 1)
MSB first (LSBFE = 0):
LSB first (LSBFE = 1): MSB
LSB LSB
MSB
Bit 5
Bit 2
Bit 6
Bit 1 Bit 4
Bit 3 Bit 3
Bit 4 Bit 2
Bit 5 Bit 1
Bit 6
CHANGE O
SEL SS (I)
MOSI pin
MISO pin
Master only
MOSI/MISO
tL = Minimum leading time before the first SCK edge, not required for back to back transfers
tT = Minimum trailing time after the last SCK edge
tI = Minimum idling time between transfers (minimum SS high time), not required for back to back transfers
1 234 56 78910111213141516SCK Edge Nr.
End of Idle State Begin of Idle State
Chapter 11 Serial Peripheral Interface (SPIV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
376 Freescale Semiconductor
The baud rate generator is activated only when the SPI is in the master mode and a serial transfer is taking
place. In the other cases, the divider is disabled to decrease IDD current.
Figure 11-11. Baud Rate Divisor Equation
11.4.5 Special Features
11.4.5.1 SS Output
The SS output feature automatically drives the SS pin low during transmission to select external devices
and drives it high during idle to deselect external devices. When SS output is selected, the SS output pin
is connected to the SS input pin of the external device.
The SS output is available only in master mode during normal SPI operation by asserting SSOE and
MODFEN bit as shown in Table 11-3.
The mode fault feature is disabled while SS output is enabled.
NOTE
Care must be taken when using the SS output feature in a multimaster
system because the mode fault feature is not available for detecting system
errors between masters.
11.4.5.2 Bidirectional Mode (MOSI or MISO)
The bidirectional mode is selected when the SPC0 bit is set in SPI Control Register 2 (see Table 11-9). In
this mode, the SPI uses only one serial data pin for the interface with external device(s). The MSTR bit
decides which pin to use. The MOSI pin becomes the serial data I/O (MOMI) pin for the master mode, and
the MISO pin becomes serial data I/O (SISO) pin for the slave mode. The MISO pin in master mode and
MOSI pin in slave mode are not used by the SPI.
Table 11-9. Normal Mode and Bidirectional Mode
When SPE = 1 Master Mode MSTR = 1 Slave Mode MSTR = 0
Normal Mode
SPC0 = 0
Bidirectional Mode
SPC0 = 1
BaudRateDivisor SPPR 1+()2SPR 1+()
=
SPI
MOSI
MISO
Serial Out
Serial In
SPI
MOSI
MISO
Serial In
Serial Out
SPI
MOMI
Serial Out
Serial In
BIDIROE SPI
SISO
Serial In
Serial Out
BIDIROE
Chapter 11 Serial Peripheral Interface (SPIV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 377
The direction of each serial I/O pin depends on the BIDIROE bit. If the pin is configured as an output,
serial data from the shift register is driven out on the pin. The same pin is also the serial input to the shift
register.
The SCK is output for the master mode and input for the slave mode.
The SS is the input or output for the master mode, and it is always the input for the slave mode.
The bidirectional mode does not affect SCK and SS functions.
NOTE
In bidirectional master mode, with mode fault enabled, both data pins MISO
and MOSI can be occupied by the SPI, though MOSI is normally used for
transmissions in bidirectional mode and MISO is not used by the SPI. If a
mode fault occurs, the SPI is automatically switched to slave mode, in this
case MISO becomes occupied by the SPI and MOSI is not used. This has to
be considered, if the MISO pin is used for other purpose.
11.4.6 Error Conditions
The SPI has one error condition:
Mode fault error
11.4.6.1 Mode Fault Error
If the SS input becomes low while the SPI is configured as a master, it indicates a system error where more
than one master may be trying to drive the MOSI and SCK lines simultaneously. This condition is not
permitted in normal operation, the MODF bit in the SPI Status Register is set automatically provided the
MODFEN bit is set.
In the special case where the SPI is in master mode and MODFEN bit is cleared, the SS pin is not used by
the SPI. In this special case, the mode fault error function is inhibited and MODF remains cleared. In case
the SPI system is configured as a slave, the SS pin is a dedicated input pin. Mode fault error doesn’t occur
in slave mode.
If a mode fault error occurs the SPI is switched to slave mode, with the exception that the slave output
buffer is disabled. So SCK, MISO and MOSI pins are forced to be high impedance inputs to avoid any
possibility of conflict with another output driver. A transmission in progress is aborted and the SPI is
forced into idle state.
If the mode fault error occurs in the bidirectional mode for a SPI system configured in master mode, output
enable of the MOMI (MOSI in bidirectional mode) is cleared if it was set. No mode fault error occurs in
the bidirectional mode for SPI system configured in slave mode.
The mode fault flag is cleared automatically by a read of the SPI Status Register (with MODF set) followed
by a write to SPI Control Register 1. If the mode fault flag is cleared, the SPI becomes a normal master or
slave again.
Chapter 11 Serial Peripheral Interface (SPIV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
378 Freescale Semiconductor
11.4.7 Operation in Run Mode
In run mode with the SPI system enable (SPE) bit in the SPI control register clear, the SPI system is in a
low-power, disabled state. SPI registers remain accessible, but clocks to the core of this module are
disabled.
11.4.8 Operation in Wait Mode
SPI operation in wait mode depends upon the state of the SPISWAI bit in SPI Control Register 2.
If SPISWAI is clear, the SPI operates normally when the CPU is in wait mode
If SPISWAI is set, SPI clock generation ceases and the SPI module enters a power conservation
state when the CPU is in wait mode.
If SPISWAI is set and the SPI is configured for master, any transmission and reception in
progress stops at wait mode entry. The transmission and reception resumes when the SPI exits
wait mode.
If SPISWAI is set and the SPI is configured as a slave, any transmission and reception in
progress continues if the SCK continues to be driven from the master. This keeps the slave
synchronized to the master and the SCK.
If the master transmits several bytes while the slave is in wait mode, the slave will continue to
send out bytes consistent with the operation mode at the start of wait mode (i.e. If the slave is
currently sending its SPIDR to the master, it will continue to send the same byte. Else if the
slave is currently sending the last received byte from the master, it will continue to send each
previous master byte).
NOTE
Care must be taken when expecting data from a master while the slave is in
wait or stop mode. Even though the shift register will continue to operate,
the rest of the SPI is shut down (i.e. a SPIF interrupt will not be generated
until exiting stop or wait mode). Also, the byte from the shift register will
not be copied into the SPIDR register until after the slave SPI has exited wait
or stop mode. A SPIF flag and SPIDR copy is only generated if wait mode
is entered or exited during a tranmission. If the slave enters wait mode in idle
mode and exits wait mode in idle mode, neither a SPIF nor a SPIDR copy
will occur.
11.4.9 Operation in Stop Mode
Stop mode is dependent on the system. The SPI enters stop mode when the module clock is disabled (held
high or low). If the SPI is in master mode and exchanging data when the CPU enters stop mode, the
transmission is frozen until the CPU exits stop mode. After stop, data to and from the external SPI is
exchanged correctly. In slave mode, the SPI will stay synchronized with the master.
The stop mode is not dependent on the SPISWAI bit.
Chapter 11 Serial Peripheral Interface (SPIV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 379
11.5 Reset
The reset values of registers and signals are described in the Memory Map and Registers section (see
Section 11.3, “Memory Map and Register Definition”) which details the registers and their bit-fields.
If a data transmission occurs in slave mode after reset without a write to SPIDR, it will transmit
garbage, or the byte last received from the master before the reset.
Reading from the SPIDR after reset will always read a byte of zeros.
11.6 Interrupts
The SPIV3 only originates interrupt requests when SPI is enabled (SPE bit in SPICR1 set). The following
is a description of how the SPIV3 makes a request and how the MCU should acknowledge that request.
The interrupt vector offset and interrupt priority are chip dependent.
The interrupt flags MODF, SPIF and SPTEF are logically ORed to generate an interrupt request.
11.6.1 MODF
MODF occurs when the master detects an error on the SS pin. The master SPI must be configured for the
MODF feature (see Table 11-3). After MODF is set, the current transfer is aborted and the following bit is
changed:
MSTR = 0, The master bit in SPICR1 resets.
The MODF interrupt is reflected in the status register MODF flag. Clearing the flag will also clear the
interrupt. This interrupt will stay active while the MODF flag is set. MODF has an automatic clearing
process which is described in Section 11.3.2.4, “SPI Status Register (SPISR).
11.6.2 SPIF
SPIF occurs when new data has been received and copied to the SPI Data Register. After SPIF is set, it
does not clear until it is serviced. SPIF has an automatic clearing process which is described in
Section 11.3.2.4, “SPI Status Register (SPISR).In the event that the SPIF is not serviced before the end
of the next transfer (i.e. SPIF remains active throughout another transfer), the latter transfers will be
ignored and no new data will be copied into the SPIDR.
11.6.3 SPTEF
SPTEF occurs when the SPI Data Register is ready to accept new data. After SPTEF is set, it does not clear
until it is serviced. SPTEF has an automatic clearing process which is described in Section 11.3.2.4, “SPI
Status Register (SPISR).
Chapter 11 Serial Peripheral Interface (SPIV3) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
380 Freescale Semiconductor
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 381
Chapter 12
Pulse-Width Modulator (S12PWM8B8CV1)
12.1 Introduction
The PWM definition is based on the HC12 PWM definitions. It contains the basic features from the HC11
with some of the enhancements incorporated on the HC12: center aligned output mode and four available
clock sources.The PWM module has eight channels with independent control of left and center aligned
outputs on each channel.
Each of the eight channels has a programmable period and duty cycle as well as a dedicated counter. A
flexible clock select scheme allows a total of four different clock sources to be used with the counters. Each
of the modulators can create independent continuous waveforms with software-selectable duty rates from
0% to 100%. The PWM outputs can be programmed as left aligned outputs or center aligned outputs.
12.1.1 Features
The PWM block includes these distinctive features:
Eight independent PWM channels with programmable period and duty cycle
Dedicated counter for each PWM channel
Programmable PWM enable/disable for each channel
Software selection of PWM duty pulse polarity for each channel
Period and duty cycle are double buffered. Change takes effect when the end of the effective period
is reached (PWM counter reaches zero) or when the channel is disabled.
Programmable center or left aligned outputs on individual channels
Eight 8-bit channel or four 16-bit channel PWM resolution
Four clock sources (A, B, SA, and SB) provide for a wide range of frequencies
Programmable clock select logic
Emergency shutdown
12.1.2 Modes of Operation
There is a software programmable option for low power consumption in wait mode that disables the input
clock to the prescaler.
In freeze mode there is a software programmable option to disable the input clock to the prescaler. This is
useful for emulation.
Chapter 12 Pulse-Width Modulator (S12PWM8B8CV1)
MC9S12KG128 Data Sheet, Rev. 1.16
382 Freescale Semiconductor
12.1.3 Block Diagram
Figure 12-1 shows the block diagram for the 8-bit 8-channel PWM block.
Figure 12-1. PWM Block Diagram
12.2 External Signal Description
The PWM module has a total of 8 external pins.
12.2.1 PWM7 — PWM Channel 7
This pin serves as waveform output of PWM channel 7 and as an input for the emergency shutdown
feature.
12.2.2 PWM6 — PWM Channel 6
This pin serves as waveform output of PWM channel 6.
Period and Duty Counter
Channel 6
Clock Select PWM Clock
Period and Duty Counter
Channel 5
Period and Duty Counter
Channel 4
Period and Duty Counter
Channel 3
Period and Duty Counter
Channel 2
Period and Duty Counter
Channel 1
Alignment
Polarity
Control
PWM8B8C
PWM6
PWM5
PWM4
PWM3
PWM2
PWM1
Enable
PWM Channels
Period and Duty Counter
Channel 7
Period and Duty Counter
Channel 0 PWM0
PWM7
Bus Clock
Chapter 12 Pulse-Width Modulator (S12PWM8B8CV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 383
12.2.3 PWM5 — PWM Channel 5
This pin serves as waveform output of PWM channel 5.
12.2.4 PWM4 — PWM Channel 4
This pin serves as waveform output of PWM channel 4.
12.2.5 PWM3 — PWM Channel 3
This pin serves as waveform output of PWM channel 3.
12.2.6 PWM3 — PWM Channel 2
This pin serves as waveform output of PWM channel 2.
12.2.7 PWM3 — PWM Channel 1
This pin serves as waveform output of PWM channel 1.
12.2.8 PWM3 — PWM Channel 0
This pin serves as waveform output of PWM channel 0.
12.3 Memory Map and Register Definition
This section describes in detail all the registers and register bits in the PWM module.
The special-purpose registers and register bit functions that are not normally available to device end users,
such as factory test control registers and reserved registers, are clearly identified by means of shading the
appropriate portions of address maps and register diagrams. Notes explaining the reasons for restricting
access to the registers and functions are also explained in the individual register descriptions.
12.3.1 Module Memory Map
This section describes the content of the registers in the PWM module. The base address of the PWM
module is determined at the MCU level when the MCU is defined. The register decode map is fixed and
begins at the first address of the module address offset. The figure below shows the registers associated
with the PWM and their relative offset from the base address. The register detail description follows the
order they appear in the register map.
Reserved bits within a register will always read as 0 and the write will be unimplemented. Unimplemented
functions are indicated by shading the bit. .
Chapter 12 Pulse-Width Modulator (S12PWM8B8CV1)
MC9S12KG128 Data Sheet, Rev. 1.16
384 Freescale Semiconductor
NOTE
Register Address = Base Address + Address Offset, where the Base Address
is defined at the MCU level and the Address Offset is defined at the module
level.
12.3.2 Register Descriptions
This section describes in detail all the registers and register bits in the PWM module.
Register
Name Bit 7 6 5 4 3 2 1 Bit 0
0x0000
PWME RPWME7 PWME6 PWME5 PWME4 PWME3 PWME2 PWME1 PWME0
W
0x0001
PWMPOL RPPOL7 PPOL6 PPOL5 PPOL4 PPOL3 PPOL2 PPOL1 PPOL0
W
0x0002
PWMCLK RPCLK7 PCLKL6 PCLK5 PCLK4 PCLK3 PCLK2 PCLK1 PCLK0
W
0x0003
PWMPRCLK R0 PCKB2 PCKB1 PCKB0 0PCKA2 PCKA1 PCKA0
W
0x0004
PWMCAE RCAE7 CAE6 CAE5 CAE4 CAE3 CAE2 CAE1 CAE0
W
0x0005
PWMCTL RCON67 CON45 CON23 CON01 PSWAI PFRZ 00
W
0x0006
PWMTST1R00000000
W
0x0007
PWMPRSC1R00000000
W
0x0008
PWMSCLA RBit 7 6 5 4 3 2 1 Bit 0
W
0x0009
PWMSCLB RBit 7 6 5 4 3 2 1 Bit 0
W
0x000A
PWMSCNTA
1
R00000000
W
= Unimplemented or Reserved
Figure 12-2. PWM Register Summary (Sheet 1 of 3)
Chapter 12 Pulse-Width Modulator (S12PWM8B8CV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 385
0x000B
PWMSCNTB
1
R00000000
W
0x000C
PWMCNT0 R Bit 7 6 5 4 3 2 1 Bit 0
W00000000
0x000D
PWMCNT1 R Bit 7 6 5 4 3 2 1 Bit 0
W00000000
0x000E
PWMCNT2 R Bit 7 6 5 4 3 2 1 Bit 0
W00000000
0x000F
PWMCNT3 R Bit 7 6 5 4 3 2 1 Bit 0
W00000000
0x0010
PWMCNT4 R Bit 7 6 5 4 3 2 1 Bit 0
W00000000
0x0011
PWMCNT5 R Bit 7 6 5 4 3 2 1 Bit 0
W00000000
0x0012
PWMCNT6 R Bit 7 6 5 4 3 2 1 Bit 0
W00000000
0x0013
PWMCNT7 R Bit 7 6 5 4 3 2 1 Bit 0
W00000000
0x0014
PWMPER0 RBit 7 6 5 4 3 2 1 Bit 0
W
0x0015
PWMPER1 RBit 7 6 5 4 3 2 1 Bit 0
W
0x0016
PWMPER2 RBit 7 6 5 4 3 2 1 Bit 0
W
0x0017
PWMPER3 RBit 7 6 5 4 3 2 1 Bit 0
W
0x0018
PWMPER4 RBit 7 6 5 4 3 2 1 Bit 0
W
0x0019
PWMPER5 RBit 7 6 5 4 3 2 1 Bit 0
W
Register
Name Bit 7 6 5 4 3 2 1 Bit 0
= Unimplemented or Reserved
Figure 12-2. PWM Register Summary (Sheet 2 of 3)
Chapter 12 Pulse-Width Modulator (S12PWM8B8CV1)
MC9S12KG128 Data Sheet, Rev. 1.16
386 Freescale Semiconductor
12.3.2.1 PWM Enable Register (PWME)
Each PWM channel has an enable bit (PWMEx) to start its waveform output. When any of the PWMEx
bits are set (PWMEx = 1), the associated PWM output is enabled immediately. However, the actual PWM
waveform is not available on the associated PWM output until its clock source begins its next cycle due to
the synchronization of PWMEx and the clock source.
NOTE
The first PWM cycle after enabling the channel can be irregular.
0x001A
PWMPER6 RBit 7 6 5 4 3 2 1 Bit 0
W
0x001B
PWMPER7 RBit 7 6 5 4 3 2 1 Bit 0
W
0x001C
PWMDTY0 RBit 7 6 5 4 3 2 1 Bit 0
W
0x001D
PWMDTY1 RBit 7 6 5 4 3 2 1 Bit 0
W
0x001E
PWMDTY2 RBit 7 6 5 4 3 2 1 Bit 0
W
0x001F
PWMDTY3 RBit 7 6 5 4 3 2 1 Bit 0
W
0x0010
PWMDTY4 RBit 7 6 5 4 3 2 1 Bit 0
W
0x0021
PWMDTY5 RBit 7 6 5 4 3 2 1 Bit 0
W
0x0022
PWMDTY6 RBit 7 6 5 4 3 2 1 Bit 0
W
0x0023
PWMDTY7 RBit 7 6 5 4 3 2 1 Bit 0
W
0x0024
PWMSDN RPWMIF PWMIE 0PWMLVL 0 PWM7IN PWM7INL PWM7ENA
W PWMRSTRT
1Intended for factory test purposes only.
Register
Name Bit 7 6 5 4 3 2 1 Bit 0
= Unimplemented or Reserved
Figure 12-2. PWM Register Summary (Sheet 3 of 3)
Chapter 12 Pulse-Width Modulator (S12PWM8B8CV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 387
An exception to this is when channels are concatenated. Once concatenated mode is enabled (CONxx bits
set in PWMCTL register), enabling/disabling the corresponding 16-bit PWM channel is controlled by the
low order PWMEx bit.In this case, the high order bytes PWMEx bits have no effect and their
corresponding PWM output lines are disabled.
While in run mode, if all eight PWM channels are disabled (PWME7–0 = 0), the prescaler counter shuts
off for power savings.
Read: Anytime
Write: Anytime
Module Base + 0x0000
76543210
RPWME7 PWME6 PWME5 PWME4 PWME3 PWME2 PWME1 PWME0
W
Reset 0 0 0 00000
Figure 12-3. PWM Enable Register (PWME)
Table 12-1. PWME Field Descriptions
Field Description
7
PWME7 Pulse Width Channel 7 Enable
0 Pulse width channel 7 is disabled.
1 Pulse width channel 7 is enabled. The pulse modulated signal becomes available at PWM output bit 7 when
its clock source begins its next cycle.
6
PWME6 Pulse Width Channel 6 Enable
0 Pulse width channel 6 is disabled.
1 Pulse width channel 6 is enabled. The pulse modulated signal becomes available at PWM output bit6 when
its clock source begins its next cycle. If CON67=1, then bit has no effect and PWM output line 6 is disabled.
5
PWME5 Pulse Width Channel 5 Enable
0 Pulse width channel 5 is disabled.
1 Pulse width channel 5 is enabled. The pulse modulated signal becomes available at PWM output bit 5 when
its clock source begins its next cycle.
4
PWME4 Pulse Width Channel 4 Enable
0 Pulse width channel 4 is disabled.
1 Pulse width channel 4 is enabled. The pulse modulated signal becomes available at PWM, output bit 4 when
its clock source begins its next cycle. If CON45 = 1, then bit has no effect and PWM output bit4 is disabled.
3
PWME3 Pulse Width Channel 3 Enable
0 Pulse width channel 3 is disabled.
1 Pulse width channel 3 is enabled. The pulse modulated signal becomes available at PWM, output bit 3 when
its clock source begins its next cycle.
2
PWME2 Pulse Width Channel 2 Enable
0 Pulse width channel 2 is disabled.
1 Pulse width channel 2 is enabled. The pulse modulated signal becomes available at PWM, output bit 2 when
its clock source begins its next cycle. If CON23 = 1, then bit has no effect and PWM output bit2 is disabled.
Chapter 12 Pulse-Width Modulator (S12PWM8B8CV1)
MC9S12KG128 Data Sheet, Rev. 1.16
388 Freescale Semiconductor
12.3.2.2 PWM Polarity Register (PWMPOL)
The starting polarity of each PWM channel waveform is determined by the associated PPOLx bit in the
PWMPOL register. If the polarity bit is one, the PWM channel output is high at the beginning of the cycle
and then goes low when the duty count is reached. Conversely, if the polarity bit is zero, the output starts
low and then goes high when the duty count is reached.
Read: Anytime
Write: Anytime
NOTE
PPOLx register bits can be written anytime. If the polarity is changed while
a PWM signal is being generated, a truncated or stretched pulse can occur
during the transition
12.3.2.3 PWM Clock Select Register (PWMCLK)
Each PWM channel has a choice of two clocks to use as the clock source for that channel as described
below.
1
PWME1 Pulse Width Channel 1 Enable
0 Pulse width channel 1 is disabled.
1 Pulse width channel 1 is enabled. The pulse modulated signal becomes available at PWM, output bit 1 when
its clock source begins its next cycle.
0
PWME0 Pulse Width Channel 0 Enable
0 Pulse width channel 0 is disabled.
1 Pulse width channel 0 is enabled. The pulse modulated signal becomes available at PWM, output bit 0 when
its clock source begins its next cycle. If CON01 = 1, then bit has no effect and PWM output line0 is disabled.
Module Base + 0x0001
76543210
RPPOL7 PPOL6 PPOL5 PPOL4 PPOL3 PPOL2 PPOL1 PPOL0
W
Reset 0 0 0 00000
Figure 12-4. PWM Polarity Register (PWMPOL)
Table 12-2. PWMPOL Field Descriptions
Field Description
7–0
PPOL[7:0] Pulse Width Channel 7–0 Polarity Bits
0 PWM channel 7–0 outputs are low at the beginning of the period, then go high when the duty count is
reached.
1 PWM channel 7–0 outputs are high at the beginning of the period, then go low when the duty count is
reached.
Table 12-1. PWME Field Descriptions (continued)
Field Description
Chapter 12 Pulse-Width Modulator (S12PWM8B8CV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 389
Read: Anytime
Write: Anytime
NOTE
Register bits PCLK0 to PCLK7 can be written anytime. If a clock select is
changed while a PWM signal is being generated, a truncated or stretched
pulse can occur during the transition.
12.3.2.4 PWM Prescale Clock Select Register (PWMPRCLK)
This register selects the prescale clock source for clocks A and B independently.
Module Base + 0x0002
76543210
RPCLK7 PCLKL6 PCLK5 PCLK4 PCLK3 PCLK2 PCLK1 PCLK0
W
Reset 0 0 0 00000
Figure 12-5. PWM Clock Select Register (PWMCLK)
Table 12-3. PWMCLK Field Descriptions
Field Description
7
PCLK7 Pulse Width Channel 7 Clock Select
0 Clock B is the clock source for PWM channel 7.
1 Clock SB is the clock source for PWM channel 7.
6
PCLK6 Pulse Width Channel 6 Clock Select
0 Clock B is the clock source for PWM channel 6.
1 Clock SB is the clock source for PWM channel 6.
5
PCLK5 Pulse Width Channel 5 Clock Select
0 Clock A is the clock source for PWM channel 5.
1 Clock SA is the clock source for PWM channel 5.
4
PCLK4 Pulse Width Channel 4 Clock Select
0 Clock A is the clock source for PWM channel 4.
1 Clock SA is the clock source for PWM channel 4.
3
PCLK3 Pulse Width Channel 3 Clock Select
0 Clock B is the clock source for PWM channel 3.
1 Clock SB is the clock source for PWM channel 3.
2
PCLK2 Pulse Width Channel 2 Clock Select
0 Clock B is the clock source for PWM channel 2.
1 Clock SB is the clock source for PWM channel 2.
1
PCLK1 Pulse Width Channel 1 Clock Select
0 Clock A is the clock source for PWM channel 1.
1 Clock SA is the clock source for PWM channel 1.
0
PCLK0 Pulse Width Channel 0 Clock Select
0 Clock A is the clock source for PWM channel 0.
1 Clock SA is the clock source for PWM channel 0.
Chapter 12 Pulse-Width Modulator (S12PWM8B8CV1)
MC9S12KG128 Data Sheet, Rev. 1.16
390 Freescale Semiconductor
Read: Anytime
Write: Anytime
NOTE
PCKB2–0 and PCKA2–0 register bits can be written anytime. If the clock
pre-scale is changed while a PWM signal is being generated, a truncated or
stretched pulse can occur during the transition.
s
Module Base + 0x0003
76543210
R0 PCKB2 PCKB1 PCKB0 0PCKA2 PCKA1 PCKA0
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 12-6. PWM Prescale Clock Select Register (PWMPRCLK)
Table 12-4. PWMPRCLK Field Descriptions
Field Description
6–4
PCKB[2:0] Prescaler Select for Clock B Clock B is one of two clock sources which can be used for channels 2, 3, 6, or
7. These three bits determine the rate of clock B, as shown in Table 12-5.
2–0
PCKA[2:0] Prescaler Select for Clock A Clock A is one of two clock sources which can be used for channels 0, 1, 4 or
5. These three bits determine the rate of clock A, as shown in Table 12-6.
Table 12-5. Clock B Prescaler Selects
PCKB2 PCKB1 PCKB0 Value of Clock B
0 0 0 Bus clock
0 0 1 Bus clock / 2
0 1 0 Bus clock / 4
0 1 1 Bus clock / 8
1 0 0 Bus clock / 16
1 0 1 Bus clock / 32
1 1 0 Bus clock / 64
1 1 1 Bus clock / 128
Table 12-6. Clock A Prescaler Selects
PCKA2 PCKA1 PCKA0 Value of Clock A
0 0 0 Bus clock
0 0 1 Bus clock / 2
0 1 0 Bus clock / 4
0 1 1 Bus clock / 8
1 0 0 Bus clock / 16
1 0 1 Bus clock / 32
1 1 0 Bus clock / 64
1 1 1 Bus clock / 128
Chapter 12 Pulse-Width Modulator (S12PWM8B8CV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 391
12.3.2.5 PWM Center Align Enable Register (PWMCAE)
The PWMCAE register contains eight control bits for the selection of center aligned outputs or left aligned
outputs for each PWM channel. If the CAEx bit is set to a one, the corresponding PWM output will be
center aligned. If the CAEx bit is cleared, the corresponding PWM output will be left aligned. See
Section 12.4.2.5, “Left Aligned Outputs” and Section 12.4.2.6, “Center Aligned Outputs” for a more
detailed description of the PWM output modes.
Read: Anytime
Write: Anytime
NOTE
Write these bits only when the corresponding channel is disabled.
12.3.2.6 PWM Control Register (PWMCTL)
The PWMCTL register provides for various control of the PWM module.
Read: Anytime
Write: Anytime
There are three control bits for concatenation, each of which is used to concatenate a pair of PWM
channels into one 16-bit channel. When channels 6 and 7are concatenated, channel 6 registers become the
high order bytes of the double byte channel. When channels 4 and 5 are concatenated, channel 4 registers
become the high order bytes of the double byte channel. When channels 2 and 3 are concatenated, channel
Module Base + 0x0004
76543210
RCAE7 CAE6 CAE5 CAE4 CAE3 CAE2 CAE1 CAE0
W
Reset 0 0 0 00000
Figure 12-7. PWM Center Align Enable Register (PWMCAE)
Table 12-7. PWMCAE Field Descriptions
Field Description
7–0
CAE[7:0] Center Aligned Output Modes on Channels 7–0
0 Channels 7–0 operate in left aligned output mode.
1 Channels 7–0 operate in center aligned output mode.
Module Base + 0x0005
76543210
RCON67 CON45 CON23 CON01 PSWAI PFRZ 00
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 12-8. PWM Control Register (PWMCTL)
Chapter 12 Pulse-Width Modulator (S12PWM8B8CV1)
MC9S12KG128 Data Sheet, Rev. 1.16
392 Freescale Semiconductor
2 registers become the high order bytes of the double byte channel. When channels 0 and 1 are
concatenated, channel 0 registers become the high order bytes of the double byte channel.
See Section 12.4.2.7, “PWM 16-Bit Functions” for a more detailed description of the concatenation PWM
Function.
NOTE
Change these bits only when both corresponding channels are disabled.
Table 12-8. PWMCTL Field Descriptions
Field Description
7
CON67 Concatenate Channels 6 and 7
0 Channels 6 and 7 are separate 8-bit PWMs.
1 Channels 6 and 7 are concatenated to create one 16-bit PWM channel. Channel 6 becomes the high order
byte and channel 7 becomes the low order byte. Channel 7 output pin is used as the output for this 16-bit
PWM (bit 7 of port PWMP). Channel 7 clock select control-bit determines the clock source, channel 7 polarity
bit determines the polarity, channel 7 enable bit enables the output and channel 7 center aligned enable bit
determines the output mode.
6
CON45 Concatenate Channels 4 and 5
0 Channels 4 and 5 are separate 8-bit PWMs.
1 Channels 4 and 5 are concatenated to create one 16-bit PWM channel. Channel 4 becomes the high order
byte and channel 5 becomes the low order byte. Channel 5 output pin is used as the output for this 16-bit
PWM (bit 5 of port PWMP). Channel 5 clock select control-bit determines the clock source, channel 5 polarity
bit determines the polarity, channel 5 enable bit enables the output and channel 5 center aligned enable bit
determines the output mode.
5
CON23 Concatenate Channels 2 and 3
0 Channels 2 and 3 are separate 8-bit PWMs.
1 Channels 2 and 3 are concatenated to create one 16-bit PWM channel. Channel 2 becomes the high order
byte and channel 3 becomes the low order byte. Channel 3 output pin is used as the output for this 16-bit
PWM (bit 3 of port PWMP). Channel 3 clock select control-bit determines the clock source, channel 3 polarity
bit determines the polarity, channel 3 enable bit enables the output and channel 3 center aligned enable bit
determines the output mode.
4
CON01 Concatenate Channels 0 and 1
0 Channels 0 and 1 are separate 8-bit PWMs.
1 Channels 0 and 1 are concatenated to create one 16-bit PWM channel. Channel 0 becomes the high order
byte and channel 1 becomes the low order byte. Channel 1 output pin is used as the output for this 16-bit
PWM (bit 1 of port PWMP). Channel 1 clock select control-bit determines the clock source, channel 1 polarity
bit determines the polarity, channel 1 enable bit enables the output and channel 1 center aligned enable bit
determines the output mode.
3
PSWAI PWM Stops in Wait Mode — Enabling this bit allows for lower power consumption in wait mode by disabling
the input clock to the prescaler.
0 Allow the clock to the prescaler to continue while in wait mode.
1 Stop the input clock to the prescaler whenever the MCU is in wait mode.
2
PFREZ PWM Counters Stop in Freeze Mode — In freeze mode, there is an option to disable the input clock to the
prescaler by setting the PFRZ bit in the PWMCTL register. If this bit is set, whenever the MCU is in freeze mode,
the input clock to the prescaler is disabled. This feature is useful during emulation as it allows the PWM function
to be suspended. In this way, the counters of the PWM can be stopped while in freeze mode so that once normal
program flow is continued, the counters are re-enabled to simulate real-time operations. Since the registers can
still be accessed in this mode, to re-enable the prescaler clock, either disable the PFRZ bit or exit freeze mode.
0 Allow PWM to continue while in freeze mode.
1 Disable PWM input clock to the prescaler whenever the part is in freeze mode. This is useful for emulation.
Chapter 12 Pulse-Width Modulator (S12PWM8B8CV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 393
12.3.2.7 Reserved Register (PWMTST)
This register is reserved for factory testing of the PWM module and is not available in normal modes.
Read: Always read $00 in normal modes
Write: Unimplemented in normal modes
NOTE
Writing to this register when in special modes can alter the PWM
functionality.
12.3.2.8 Reserved Register (PWMPRSC)
This register is reserved for factory testing of the PWM module and is not available in normal modes.
Read: Always read $00 in normal modes
Write: Unimplemented in normal modes
NOTE
Writing to this register when in special modes can alter the PWM
functionality.
12.3.2.9 PWM Scale A Register (PWMSCLA)
PWMSCLA is the programmable scale value used in scaling clock A to generate clock SA. Clock SA is
generated by taking clock A, dividing it by the value in the PWMSCLA register and dividing that by two.
Clock SA = Clock A / (2 * PWMSCLA)
Module Base + 0x0006
76543210
R00000000
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 12-9. Reserved Register (PWMTST)
Module Base + 0x0007
76543210
R00000000
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 12-10. Reserved Register (PWMPRSC)
Chapter 12 Pulse-Width Modulator (S12PWM8B8CV1)
MC9S12KG128 Data Sheet, Rev. 1.16
394 Freescale Semiconductor
NOTE
When PWMSCLA = $00, PWMSCLA value is considered a full scale value
of 256. Clock A is thus divided by 512.
Any value written to this register will cause the scale counter to load the new scale value (PWMSCLA).
Read: Anytime
Write: Anytime (causes the scale counter to load the PWMSCLA value)
12.3.2.10 PWM Scale B Register (PWMSCLB)
PWMSCLB is the programmable scale value used in scaling clock B to generate clock SB. Clock SB is
generated by taking clock B, dividing it by the value in the PWMSCLB register and dividing that by two.
Clock SB = Clock B / (2 * PWMSCLB)
NOTE
When PWMSCLB = $00, PWMSCLB value is considered a full scale value
of 256. Clock B is thus divided by 512.
Any value written to this register will cause the scale counter to load the new scale value (PWMSCLB).
Read: Anytime
Write: Anytime (causes the scale counter to load the PWMSCLB value).
12.3.2.11 Reserved Registers (PWMSCNTx)
The registers PWMSCNTA and PWMSCNTB are reserved for factory testing of the PWM module and are
not available in normal modes.
Module Base + 0x0008
76543210
RBit 7 6 5 4 3 2 1 Bit 0
W
Reset 0 0 0 00000
Figure 12-11. PWM Scale A Register (PWMSCLA)
Module Base + 0x0009
76543210
RBit 7 6 5 4 3 2 1 Bit 0
W
Reset 0 0 0 00000
Figure 12-12. PWM Scale B Register (PWMSCLB)
Chapter 12 Pulse-Width Modulator (S12PWM8B8CV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 395
Read: Always read $00 in normal modes
Write: Unimplemented in normal modes
NOTE
Writing to these registers when in special modes can alter the PWM
functionality.
12.3.2.12 PWM Channel Counter Registers (PWMCNTx)
Each channel has a dedicated 8-bit up/down counter which runs at the rate of the selected clock source.
The counter can be read at any time without affecting the count or the operation of the PWM channel. In
left aligned output mode, the counter counts from 0 to the value in the period register - 1. In center aligned
output mode, the counter counts from 0 up to the value in the period register and then back down to 0.
Any value written to the counter causes the counter to reset to $00, the counter direction to be set to up,
the immediate load of both duty and period registers with values from the buffers, and the output to change
according to the polarity bit. The counter is also cleared at the end of the effective period (see
Section 12.4.2.5, “Left Aligned Outputs” and Section 12.4.2.6, “Center Aligned Outputs” for more
details). When the channel is disabled (PWMEx = 0), the PWMCNTx register does not count. When a
channel becomes enabled (PWMEx = 1), the associated PWM counter starts at the count in the
PWMCNTx register. For more detailed information on the operation of the counters, see Section 12.4.2.4,
“PWM Timer Counters”.
In concatenated mode, writes to the 16-bit counter by using a 16-bit access or writes to either the low or
high order byte of the counter will reset the 16-bit counter. Reads of the 16-bit counter must be made by
16-bit access to maintain data coherency.
NOTE
Writing to the counter while the channel is enabled can cause an irregular PWM cycle to occur.
Read: Anytime
Module Base + 0x000A, 0x000B
76543210
R00000000
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 12-13. Reserved Registers (PWMSCNTx)
Module Base + 0x000C = PWMCNT0, 0x000D = PWMCNT1, 0x000E = PWMCNT2, 0x000F = PWMCNT3
Module Base + 0x0010 = PWMCNT4, 0x0011 = PWMCNT5, 0x0012 = PWMCNT6, 0x0013 = PWMCNT7
76543210
R Bit 7 6 5 4 3 2 1 Bit 0
W00000000
Reset 0 0 0 00000
Figure 12-14. PWM Channel Counter Registers (PWMCNTx)
Chapter 12 Pulse-Width Modulator (S12PWM8B8CV1)
MC9S12KG128 Data Sheet, Rev. 1.16
396 Freescale Semiconductor
Write: Anytime (any value written causes PWM counter to be reset to $00).
12.3.2.13 PWM Channel Period Registers (PWMPERx)
There is a dedicated period register for each channel. The value in this register determines the period of
the associated PWM channel.
The period registers for each channel are double buffered so that if they change while the channel is
enabled, the change will NOT take effect until one of the following occurs:
The effective period ends
The counter is written (counter resets to $00)
The channel is disabled
In this way, the output of the PWM will always be either the old waveform or the new waveform, not some
variation in between. If the channel is not enabled, then writes to the period register will go directly to the
latches as well as the buffer.
NOTE
Reads of this register return the most recent value written. Reads do not
necessarily return the value of the currently active period due to the double
buffering scheme.
See Section 12.4.2.3, “PWM Period and Duty” for more information.
To calculate the output period, take the selected clock source period for the channel of interest (A, B, SA,
or SB) and multiply it by the value in the period register for that channel:
Left aligned output (CAEx = 0)
PWMxPeriod =ChannelClockPeriod *PWMPERxCenterAlignedOutput(CAEx= 1)
PWMx Period = Channel Clock Period * (2 * PWMPERx)
For boundary case programming values, please refer to Section 12.4.2.8, “PWM Boundary Cases”.
Read: Anytime
Write: Anytime
Module Base + 0x0014 = PWMPER0, 0x0015 = PWMPER1, 0x0016 = PWMPER2, 0x0017 = PWMPER3
Module Base + 0x0018 = PWMPER4, 0x0019 = PWMPER5, 0x001A = PWMPER6, 0x001B = PWMPER7
76543210
RBit 7 6 5 4 3 2 1 Bit 0
W
Reset 1 1 1 11111
Figure 12-15. PWM Channel Period Registers (PWMPERx)
Chapter 12 Pulse-Width Modulator (S12PWM8B8CV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 397
12.3.2.14 PWM Channel Duty Registers (PWMDTYx)
There is a dedicated duty register for each channel. The value in this register determines the duty of the
associated PWM channel. The duty value is compared to the counter and if it is equal to the counter value
a match occurs and the output changes state.
The duty registers for each channel are double buffered so that if they change while the channel is enabled,
the change will NOT take effect until one of the following occurs:
The effective period ends
The counter is written (counter resets to $00)
The channel is disabled
In this way, the output of the PWM will always be either the old duty waveform or the new duty waveform,
not some variation in between. If the channel is not enabled, then writes to the duty register will go directly
to the latches as well as the buffer.
NOTE
Reads of this register return the most recent value written. Reads do not
necessarily return the value of the currently active duty due to the double
buffering scheme.
See Section 12.4.2.3, “PWM Period and Duty” for more information.
NOTE
Depending on the polarity bit, the duty registers will contain the count of
either the high time or the low time. If the polarity bit is one, the output starts
high and then goes low when the duty count is reached, so the duty registers
contain a count of the high time. If the polarity bit is zero, the output starts
low and then goes high when the duty count is reached, so the duty registers
contain a count of the low time.
To calculate the output duty cycle (high time as a% of period) for a particular channel:
Polarity = 0 (PPOL x =0)
Duty Cycle = [(PWMPERx-PWMDTYx)/PWMPERx] * 100%
Polarity = 1 (PPOLx = 1)
Duty Cycle = [PWMDTYx / PWMPERx] * 100%
For boundary case programming values, please refer to Section 12.4.2.8, “PWM Boundary Cases”.
Read: Anytime
Module Base + 0x001C = PWMDTY0, 0x001D = PWMDTY1, 0x001E = PWMDTY2, 0x001F = PWMDTY3
Module Base + 0x0020 = PWMDTY4, 0x0021 = PWMDTY5, 0x0022 = PWMDTY6, 0x0023 = PWMDTY7
76543210
RBit 7 6 5 4 3 2 1 Bit 0
W
Reset 1 1 1 11111
Figure 12-16. PWM Channel Duty Registers (PWMDTYx)
Chapter 12 Pulse-Width Modulator (S12PWM8B8CV1)
MC9S12KG128 Data Sheet, Rev. 1.16
398 Freescale Semiconductor
Write: Anytime
12.3.2.15 PWM Shutdown Register (PWMSDN)
The PWMSDN register provides for the shutdown functionality of the PWM module in the emergency
cases. For proper operation, channel 7 must be driven to the active level for a minimum of two bus clocks.
Read: Anytime
Write: Anytime
Module Base + 0x0024
76543210
RPWMIF PWMIE 0PWMLVL 0 PWM7IN PWM7INL PWM7ENA
W PWMRSTRT
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 12-17. PWM Shutdown Register (PWMSDN)
Table 12-9. PWMSDN Field Descriptions
Field Description
7
PWMIF PWM Interrupt Flag — Any change from passive to asserted (active) state or from active to passive state will
be flagged by setting the PWMIF flag = 1. The flag is cleared by writing a logic 1 to it. Writing a 0 has no effect.
0 No change on PWM7IN input.
1 Change on PWM7IN input
6
PWMIE PWM Interrupt Enable — If interrupt is enabled an interrupt to the CPU is asserted.
0 PWM interrupt is disabled.
1 PWM interrupt is enabled.
5
PWMRSTRT PWM Restart The PWM can only be restarted if the PWM channel input 7 is de-asserted. After writing a logic
1 to the PWMRSTRT bit (trigger event) the PWM channels start running after the corresponding counter passes
next “counter == 0” phase. Also, if the PWM7ENA bit is reset to 0, the PWM do not start before the counter
passes $00. The bit is always read as “0”.
4
PWMLVL PWM Shutdown Output Level If active level as defined by the PWM7IN input, gets asserted all enabled PWM
channels are immediately driven to the level defined by PWMLVL.
0 PWM outputs are forced to 0
1 Outputs are forced to 1.
2
PWM7IN PWM Channel 7 Input Status — This reflects the current status of the PWM7 pin.
1
PWM7INL PWM Shutdown Active Input Level for Channel 7 — If the emergency shutdown feature is enabled
(PWM7ENA = 1), this bit determines the active level of the PWM7channel.
0 Active level is low
1 Active level is high
0
PWM7ENA PWM Emergency Shutdown Enable If this bit is logic 1, the pin associated with channel 7 is forced to input
and the emergency shutdown feature is enabled. All the other bits in this register are meaningful only if
PWM7ENA = 1.
0 PWM emergency feature disabled.
1 PWM emergency feature is enabled.
Chapter 12 Pulse-Width Modulator (S12PWM8B8CV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 399
12.4 Functional Description
12.4.1 PWM Clock Select
There are four available clocks: clock A, clock B, clock SA (scaled A), and clock SB (scaled B). These
four clocks are based on the bus clock.
Clock A and B can be software selected to be 1, 1/2, 1/4, 1/8,..., 1/64, 1/128 times the bus clock. Clock SA
uses clock A as an input and divides it further with a reloadable counter. Similarly, clock SB uses clock B
as an input and divides it further with a reloadable counter. The rates available for clock SA are software
selectable to be clock A divided by 2, 4, 6, 8,..., or 512 in increments of divide by 2. Similar rates are
available for clock SB. Each PWM channel has the capability of selecting one of two clocks, either the
pre-scaled clock (clock A or B) or the scaled clock (clock SA or SB).
The block diagram in Figure 12-18 shows the four different clocks and how the scaled clocks are created.
12.4.1.1 Prescale
The input clock to the PWM prescaler is the bus clock. It can be disabled whenever the part is in freeze
mode by setting the PFRZ bit in the PWMCTL register. If this bit is set, whenever the MCU is in freeze
mode (freeze mode signal active) the input clock to the prescaler is disabled. This is useful for emulation
in order to freeze the PWM. The input clock can also be disabled when all eight PWM channels are
disabled (PWME7-0 = 0). This is useful for reducing power by disabling the prescale counter.
Clock A and clock B are scaled values of the input clock. The value is software selectable for both clock
A and clock B and has options of 1, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, or 1/128 times the bus clock. The value
selected for clock A is determined by the PCKA2, PCKA1, PCKA0 bits in the PWMPRCLK register. The
value selected for clock B is determined by the PCKB2, PCKB1, PCKB0 bits also in the PWMPRCLK
register.
12.4.1.2 Clock Scale
The scaled A clock uses clock A as an input and divides it further with a user programmable value and
then divides this by 2. The scaled B clock uses clock B as an input and divides it further with a user
programmable value and then divides this by 2. The rates available for clock SA are software selectable to
be clock A divided by 2, 4, 6, 8,..., or 512 in increments of divide by 2. Similar rates are available for clock
SB.
Chapter 12 Pulse-Width Modulator (S12PWM8B8CV1)
MC9S12KG128 Data Sheet, Rev. 1.16
400 Freescale Semiconductor
Figure 12-18. PWM Clock Select Block Diagram
128248163264
PCKB2
PCKB1
PCKB0
M
U
X
Clock A
Clock B
Clock SA
Clock A/2, A/4, A/6,....A/512
Prescale Scale
Divide by
PFRZ
Freeze Mode Signal
Bus Clock
Clock Select
M
U
X
PCLK0
Clock to
PWM Ch 0
M
U
X
PCLK2
Clock to
PWM Ch 2
M
U
X
PCLK1
Clock to
PWM Ch 1
M
U
X
PCLK4
Clock to
PWM Ch 4
M
U
X
PCLK5
Clock to
PWM Ch 5
M
U
X
PCLK6
Clock to
PWM Ch 6
M
U
X
PCLK7
Clock to
PWM Ch 7
M
U
X
PCLK3
Clock to
PWM Ch 3
Load
DIV 2
PWMSCLB Clock SB
Clock B/2, B/4, B/6,....B/512
M
U
X
PCKA2
PCKA1
PCKA0
PWME7-0
Count = 1
Load
DIV 2
PWMSCLA
Count = 1
8-Bit Down
Counter
8-Bit Down
Counter
Prescaler Taps:
Chapter 12 Pulse-Width Modulator (S12PWM8B8CV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 401
Clock A is used as an input to an 8-bit down counter. This down counter loads a user programmable scale
value from the scale register (PWMSCLA). When the down counter reaches one, a pulse is output and the
8-bit counter is re-loaded. The output signal from this circuit is further divided by two. This gives a greater
range with only a slight reduction in granularity. Clock SA equals clock A divided by two times the value
in the PWMSCLA register.
NOTE
Clock SA = Clock A / (2 * PWMSCLA)
When PWMSCLA = $00, PWMSCLA value is considered a full scale value
of 256. Clock A is thus divided by 512.
Similarly, clock B is used as an input to an 8-bit down counter followed by a divide by two producing clock
SB. Thus, clock SB equals clock B divided by two times the value in the PWMSCLB register.
NOTE
Clock SB = Clock B / (2 * PWMSCLB)
When PWMSCLB = $00, PWMSCLB value is considered a full scale value
of 256. Clock B is thus divided by 512.
As an example, consider the case in which the user writes $FF into the PWMSCLA register. Clock A for
this case will be E divided by 4. A pulse will occur at a rate of once every 255x4 E cycles. Passing this
through the divide by two circuit produces a clock signal at an E divided by 2040 rate. Similarly, a value
of $01 in the PWMSCLA register when clock A is E divided by 4 will produce a clock at an E divided by
8 rate.
Writing to PWMSCLA or PWMSCLB causes the associated 8-bit down counter to be re-loaded.
Otherwise, when changing rates the counter would have to count down to $01 before counting at the proper
rate. Forcing the associated counter to re-load the scale register value every time PWMSCLA or
PWMSCLB is written prevents this.
NOTE
Writing to the scale registers while channels are operating can cause
irregularities in the PWM outputs.
12.4.1.3 Clock Select
Each PWM channel has the capability of selecting one of two clocks. For channels 0, 1, 4, and 5 the clock
choices are clock A or clock SA. For channels 2, 3, 6, and 7 the choices are clock B or clock SB. The clock
selection is done with the PCLKx control bits in the PWMCLK register.
NOTE
Changing clock control bits while channels are operating can cause
irregularities in the PWM outputs.
Chapter 12 Pulse-Width Modulator (S12PWM8B8CV1)
MC9S12KG128 Data Sheet, Rev. 1.16
402 Freescale Semiconductor
12.4.2 PWM Channel Timers
The main part of the PWM module are the actual timers. Each of the timer channels has a counter, a period
register and a duty register (each are 8-bit). The waveform output period is controlled by a match between
the period register and the value in the counter. The duty is controlled by a match between the duty register
and the counter value and causes the state of the output to change during the period. The starting polarity
of the output is also selectable on a per channel basis. Shown below in Figure 12-19 is the block diagram
for the PWM timer.
Figure 12-19. PWM Timer Channel Block Diagram
12.4.2.1 PWM Enable
Each PWM channel has an enable bit (PWMEx) to start its waveform output. When any of the PWMEx
bits are set (PWMEx = 1), the associated PWM output signal is enabled immediately. However, the actual
PWM waveform is not available on the associated PWM output until its clock source begins its next cycle
due to the synchronization of PWMEx and the clock source. An exception to this is when channels are
concatenated. Refer to Section 12.4.2.7, “PWM 16-Bit Functions” for more detail.
NOTE
The first PWM cycle after enabling the channel can be irregular.
Clock Source
T
R
Q
Q
PPOLx
From Port PWMP
Data Register
PWMEx
To Pin
Driver
Gate
8-bit Compare =
PWMDTYx
8-bit Compare =
PWMPERx
CAEx
T
R
Q
Q
8-Bit Counter
PWMCNTx
M
U
X
M
U
X
(Clock Edge
Sync)
Up/Down Reset
Chapter 12 Pulse-Width Modulator (S12PWM8B8CV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 403
On the front end of the PWM timer, the clock is enabled to the PWM circuit by the PWMEx bit being high.
There is an edge-synchronizing circuit to guarantee that the clock will only be enabled or disabled at an
edge. When the channel is disabled (PWMEx = 0), the counter for the channel does not count.
12.4.2.2 PWM Polarity
Each channel has a polarity bit to allow starting a waveform cycle with a high or low signal. This is shown
on the block diagram as a mux select of either the Q output or the Q output of the PWM output flip flop.
When one of the bits in the PWMPOL register is set, the associated PWM channel output is high at the
beginning of the waveform, then goes low when the duty count is reached. Conversely, if the polarity bit
is zero, the output starts low and then goes high when the duty count is reached.
12.4.2.3 PWM Period and Duty
Dedicated period and duty registers exist for each channel and are double buffered so that if they change
while the channel is enabled, the change will NOT take effect until one of the following occurs:
The effective period ends
The counter is written (counter resets to $00)
The channel is disabled
In this way, the output of the PWM will always be either the old waveform or the new waveform, not some
variation in between. If the channel is not enabled, then writes to the period and duty registers will go
directly to the latches as well as the buffer.
A change in duty or period can be forced into effect “immediately” by writing the new value to the duty
and/or period registers and then writing to the counter. This forces the counter to reset and the new duty
and/or period values to be latched. In addition, since the counter is readable, it is possible to know where
the count is with respect to the duty value and software can be used to make adjustments
NOTE
When forcing a new period or duty into effect immediately, an irregular
PWM cycle can occur.
Depending on the polarity bit, the duty registers will contain the count of
either the high time or the low time.
12.4.2.4 PWM Timer Counters
Each channel has a dedicated 8-bit up/down counter which runs at the rate of the selected clock source (see
Section 12.4.1, “PWM Clock Select” for the available clock sources and rates). The counter compares to
two registers, a duty register and a period register as shown in Figure 12-19. When the PWM counter
matches the duty register, the output flip-flop changes state, causing the PWM waveform to also change
state. A match between the PWM counter and the period register behaves differently depending on what
output mode is selected as shown in Figure 12-19 and described in Section 12.4.2.5, “Left Aligned
Outputs” and Section 12.4.2.6, “Center Aligned Outputs”.
Chapter 12 Pulse-Width Modulator (S12PWM8B8CV1)
MC9S12KG128 Data Sheet, Rev. 1.16
404 Freescale Semiconductor
Each channel counter can be read at anytime without affecting the count or the operation of the PWM
channel.
Any value written to the counter causes the counter to reset to $00, the counter direction to be set to up,
the immediate load of both duty and period registers with values from the buffers, and the output to change
according to the polarity bit. When the channel is disabled (PWMEx = 0), the counter stops. When a
channel becomes enabled (PWMEx = 1), the associated PWM counter continues from the count in the
PWMCNTx register. This allows the waveform to continue where it left off when the channel is
re-enabled. When the channel is disabled, writing “0” to the period register will cause the counter to reset
on the next selected clock.
NOTE
If the user wants to start a new “clean” PWM waveform without any
“history” from the old waveform, the user must write to channel counter
(PWMCNTx) prior to enabling the PWM channel (PWMEx = 1).
Generally, writes to the counter are done prior to enabling a channel in order to start from a known state.
However, writing a counter can also be done while the PWM channel is enabled (counting). The effect is
similar to writing the counter when the channel is disabled, except that the new period is started
immediately with the output set according to the polarity bit.
NOTE
Writing to the counter while the channel is enabled can cause an irregular
PWM cycle to occur.
The counter is cleared at the end of the effective period (see Section 12.4.2.5, “Left Aligned Outputs” and
Section 12.4.2.6, “Center Aligned Outputs” for more details).
12.4.2.5 Left Aligned Outputs
The PWM timer provides the choice of two types of outputs, left aligned or center aligned. They are
selected with the CAEx bits in the PWMCAE register. If the CAEx bit is cleared (CAEx = 0), the
corresponding PWM output will be left aligned.
In left aligned output mode, the 8-bit counter is configured as an up counter only. It compares to two
registers, a duty register and a period register as shown in the block diagram in Figure 12-19. When the
PWM counter matches the duty register the output flip-flop changes state causing the PWM waveform to
also change state. A match between the PWM counter and the period register resets the counter and the
output flip-flop, as shown in Figure 12-19, as well as performing a load from the double buffer period and
duty register to the associated registers, as described in Section 12.4.2.3, “PWM Period and Duty”. The
counter counts from 0 to the value in the period register – 1.
Table 12-10. PWM Timer Counter Conditions
Counter Clears ($00) Counter Counts Counter Stops
When PWMCNTx register written to
any value When PWM channel is enabled
(PWMEx = 1). Counts from last value in
PWMCNTx.
When PWM channel is disabled
(PWMEx = 0)
Effective period ends
Chapter 12 Pulse-Width Modulator (S12PWM8B8CV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 405
NOTE
Changing the PWM output mode from left aligned to center aligned output
(or vice versa) while channels are operating can cause irregularities in the
PWM output. It is recommended to program the output mode before
enabling the PWM channel.
Figure 12-20. PWM Left Aligned Output Waveform
To calculate the output frequency in left aligned output mode for a particular channel, take the selected
clock source frequency for the channel (A, B, SA, or SB) and divide it by the value in the period register
for that channel.
PWMx Frequency = Clock (A, B, SA, or SB) / PWMPERx
PWMx Duty Cycle (high time as a% of period):
Polarity = 0 (PPOLx = 0)
Duty Cycle = [(PWMPERx-PWMDTYx)/PWMPERx] * 100%
Polarity = 1 (PPOLx = 1)
Duty Cycle = [PWMDTYx / PWMPERx] * 100%
As an example of a left aligned output, consider the following case:
Clock Source = E, where E = 10 MHz (100 ns period)
PPOLx = 0
PWMPERx = 4
PWMDTYx = 1
PWMx Frequency = 10 MHz/4 = 2.5 MHz
PWMx Period = 400 ns
PWMx Duty Cycle = 3/4 *100% = 75%
The output waveform generated is shown in Figure 12-21.
PWMDTYx
Period = PWMPERx
PPOLx = 0
PPOLx = 1
Chapter 12 Pulse-Width Modulator (S12PWM8B8CV1)
MC9S12KG128 Data Sheet, Rev. 1.16
406 Freescale Semiconductor
Figure 12-21. PWM Left Aligned Output Example Waveform
12.4.2.6 Center Aligned Outputs
For center aligned output mode selection, set the CAEx bit (CAEx = 1) in the PWMCAE register and the
corresponding PWM output will be center aligned.
The 8-bit counter operates as an up/down counter in this mode and is set to up whenever the counter is
equal to $00. The counter compares to two registers, a duty register and a period register as shown in the
block diagram in Figure 12-19. When the PWM counter matches the duty register, the output flip-flop
changes state, causing the PWM waveform to also change state. A match between the PWM counter and
the period register changes the counter direction from an up-count to a down-count. When the PWM
counter decrements and matches the duty register again, the output flip-flop changes state causing the
PWM output to also change state. When the PWM counter decrements and reaches zero, the counter
direction changes from a down-count back to an up-count and a load from the double buffer period and
duty registers to the associated registers is performed, as described in Section 12.4.2.3, “PWM Period and
Duty”. The counter counts from 0 up to the value in the period register and then back down to 0. Thus the
effective period is PWMPERx*2.
NOTE
Changing the PWM output mode from left aligned to center aligned output
(or vice versa) while channels are operating can cause irregularities in the
PWM output. It is recommended to program the output mode before
enabling the PWM channel.
Figure 12-22. PWM Center Aligned Output Waveform
Period = 400 ns
E = 100 ns
Duty Cycle = 75%
PPOLx = 0
PPOLx = 1
PWMDTYx PWMDTYx
Period = PWMPERx*2
PWMPERx
PWMPERx
Chapter 12 Pulse-Width Modulator (S12PWM8B8CV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 407
To calculate the output frequency in center aligned output mode for a particular channel, take the selected
clock source frequency for the channel (A, B, SA, or SB) and divide it by twice the value in the period
register for that channel.
PWMx Frequency = Clock (A, B, SA, or SB) / (2*PWMPERx)
PWMx Duty Cycle (high time as a% of period):
Polarity = 0 (PPOLx = 0)
Duty Cycle = [(PWMPERx-PWMDTYx)/PWMPERx] * 100%
Polarity = 1 (PPOLx = 1)
Duty Cycle = [PWMDTYx / PWMPERx] * 100%
Chapter 12 Pulse-Width Modulator (S12PWM8B8CV1)
MC9S12KG128 Data Sheet, Rev. 1.16
408 Freescale Semiconductor
As an example of a center aligned output, consider the following case:
Clock Source = E, where E = 10 MHz (100 ns period)
PPOLx = 0
PWMPERx = 4
PWMDTYx = 1
PWMx Frequency = 10 MHz/8 = 1.25 MHz
PWMx Period = 800 ns
PWMx Duty Cycle = 3/4 *100% = 75%
Shown in Figure 12-23 is the output waveform generated.
Figure 12-23. PWM Center Aligned Output Example Waveform
12.4.2.7 PWM 16-Bit Functions
The PWM timer also has the option of generating 8-channels of 8-bits or 4-channels of 16-bits for greater
PWM resolution. This 16-bit channel option is achieved through the concatenation of two 8-bit channels.
The PWMCTL register contains four control bits, each of which is used to concatenate a pair of PWM
channels into one 16-bit channel. Channels 6 and 7 are concatenated with the CON67 bit, channels 4 and
5 are concatenated with the CON45 bit, channels 2 and 3 are concatenated with the CON23 bit, and
channels 0 and 1 are concatenated with the CON01 bit.
NOTE
Change these bits only when both corresponding channels are disabled.
When channels 6 and 7 are concatenated, channel 6 registers become the high order bytes of the double
byte channel, as shown in Figure 12-24. Similarly, when channels 4 and 5 are concatenated, channel 4
registers become the high order bytes of the double byte channel. When channels 2 and 3 are concatenated,
channel 2 registers become the high order bytes of the double byte channel. When channels 0 and 1 are
concatenated, channel 0 registers become the high order bytes of the double byte channel.
When using the 16-bit concatenated mode, the clock source is determined by the low order 8-bit channel
clock select control bits. That is channel 7 when channels 6 and 7 are concatenated, channel 5 when
channels 4 and 5 are concatenated, channel 3 when channels 2 and 3 are concatenated, and channel 1 when
channels 0 and 1 are concatenated. The resulting PWM is output to the pins of the corresponding low order
8-bit channel as also shown in Figure 12-24. The polarity of the resulting PWM output is controlled by the
PPOLx bit of the corresponding low order 8-bit channel as well.
E = 100 ns
DUTY CYCLE = 75%
E = 100 ns
PERIOD = 800 ns
Chapter 12 Pulse-Width Modulator (S12PWM8B8CV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 409
Figure 12-24. PWM 16-Bit Mode
Once concatenated mode is enabled (CONxx bits set in PWMCTL register), enabling/disabling the
corresponding 16-bit PWM channel is controlled by the low order PWMEx bit. In this case, the high order
bytes PWMEx bits have no effect and their corresponding PWM output is disabled.
In concatenated mode, writes to the 16-bit counter by using a 16-bit access or writes to either the low or
high order byte of the counter will reset the 16-bit counter. Reads of the 16-bit counter must be made by
16-bit access to maintain data coherency.
PWMCNT6 PWCNT7
PWM7
Clock Source 7 High Low
Period/Duty Compare
PWMCNT4 PWCNT5
PWM5
Clock Source 5 High Low
Period/Duty Compare
PWMCNT2 PWCNT3
PWM3
Clock Source 3 High Low
Period/Duty Compare
PWMCNT0 PWCNT1
PWM1
Clock Source 1 High Low
Period/Duty Compare
Chapter 12 Pulse-Width Modulator (S12PWM8B8CV1)
MC9S12KG128 Data Sheet, Rev. 1.16
410 Freescale Semiconductor
Either left aligned or center aligned output mode can be used in concatenated mode and is controlled by
the low order CAEx bit. The high order CAEx bit has no effect.
Table 12-11 is used to summarize which channels are used to set the various control bits when in 16-bit
mode.
12.4.2.8 PWM Boundary Cases
Table 12-12 summarizes the boundary conditions for the PWM regardless of the output mode (left aligned
or center aligned) and 8-bit (normal) or 16-bit (concatenation).
12.5 Resets
The reset state of each individual bit is listed within the Section 12.3.2, “Register Descriptions” which
details the registers and their bit-fields. All special functions or modes which are initialized during or just
following reset are described within this section.
The 8-bit up/down counter is configured as an up counter out of reset.
All the channels are disabled and all the counters do not count.
Table 12-11. 16-bit Concatenation Mode Summary
CONxx PWMEx PPOLx PCLKx CAEx PWMx
Output
CON67 PWME7 PPOL7 PCLK7 CAE7 PWM7
CON45 PWME5 PPOL5 PCLK5 CAE5 PWM5
CON23 PWME3 PPOL3 PCLK3 CAE3 PWM3
CON01 PWME1 PPOL1 PCLK1 CAE1 PWM1
Table 12-12. PWM Boundary Cases
PWMDTYx PWMPERx PPOLx PWMx Output
$00
(indicates no duty) >$00 1 Always low
$00
(indicates no duty) >$00 0 Always high
XX $001
(indicates no period)
1Counter = $00 and does not count.
1 Always high
XX $001
(indicates no period) 0 Always low
>= PWMPERx XX 1 Always high
>= PWMPERx XX 0 Always low
Chapter 12 Pulse-Width Modulator (S12PWM8B8CV1)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 411
12.6 Interrupts
The PWM module has only one interrupt which is generated at the time of emergency shutdown, if the
corresponding enable bit (PWMIE) is set. This bit is the enable for the interrupt. The interrupt flag PWMIF
is set whenever the input level of the PWM7 channel changes while PWM7ENA = 1 or when PWMENA
is being asserted while the level at PWM7 is active.
In stop mode or wait mode (with the PSWAI bit set), the emergency shutdown feature will drive the PWM
outputs to their shutdown output levels but the PWMIF flag will not be set.
A description of the registers involved and affected due to this interrupt is explained in Section 12.3.2.15,
“PWM Shutdown Register (PWMSDN)”.
The PWM block only generates the interrupt and does not service it. The interrupt signal name is PWM
interrupt signal.
Chapter 12 Pulse-Width Modulator (S12PWM8B8CV1)
MC9S12KG128 Data Sheet, Rev. 1.16
412 Freescale Semiconductor
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 413
Chapter 13
Timer Module (TIM16B8CV1) Block Description
13.1 Introduction
The basic timer consists of a 16-bit, software-programmable counter driven by a seven-stage
programmable prescaler.
This timer can be used for many purposes, including input waveform measurements while simultaneously
generating an output waveform. Pulse widths can vary from microseconds to many seconds.
This timer contains 8 complete input capture/output compare channels and one pulse accumulator. The
input capture function is used to detect a selected transition edge and record the time. The output compare
function is used for generating output signals or for timer software delays. The 16-bit pulse accumulator
is used to operate as a simple event counter or a gated time accumulator. The pulse accumulator shares
timer channel 7 when in event mode.
A full access for the counter registers or the input capture/output compare registers should take place in
one clock cycle. Accessing high byte and low byte separately for all of these registers may not yield the
same result as accessing them in one word.
13.1.1 Features
The TIM16B8CV1 includes these distinctive features:
Eight input capture/output compare channels.
Clock prescaling.
16-bit counter.
16-bit pulse accumulator.
13.1.2 Modes of Operation
Stop: Timer is off because clocks are stopped.
Freeze: Timer counter keep on running, unless TSFRZ in TSCR (0x0006) is set to 1.
Table 13-1. TIM_16B4C Revision History
Version
Number Revision Dates Effective
Date Author Description of Changes
01.05 05 May 2010 05 May 2010 -in 13.3.2.8/13-424,add Table 13-11
-in 13.3.2.11/13-428,TCRE bit description part,add Note
-in 13.4.3/13-437,add Figure 13-29
Chapter 13 Timer Module (TIM16B8CV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
414 Freescale Semiconductor
Wait: Counters keep on running, unless TSWAI in TSCR (0x0006) is set to 1.
Normal: Timer counter keep on running, unless TEN in TSCR (0x0006) is cleared to 0.
13.1.3 Block Diagrams
Figure 13-1. TIM16B8CV1 Block Diagram
Prescaler
16-bit Counter
Input capture
Output compare
16-bit
Pulse accumulator
IOC0
IOC2
IOC1
IOC5
IOC3
IOC4
IOC6
IOC7
PA input
interrupt
PA overflow
interrupt
Timer overflow
interrupt
Timer channel 0
interrupt
Timer channel 7
interrupt
Registers
Bus clock
Input capture
Output compare
Input capture
Output compare
Input capture
Output compare
Input capture
Output compare
Input capture
Output compare
Input capture
Output compare
Input capture
Output compare
Channel 0
Channel 1
Channel 2
Channel 3
Channel 4
Channel 5
Channel 6
Channel 7
Chapter 13 Timer Module (TIM16B8CV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 415
Figure 13-2. 16-Bit Pulse Accumulator Block Diagram
Figure 13-3. Interrupt Flag Setting
Edge detector
Intermodule Bus
PT7
M clock
Divide by 64
Clock select
CLK0
CLK1 4:1 MUX
TIMCLK
PACL K
PACLK / 256
PACLK / 65536
Prescaled clock
(PCLK)
(Timer clock)
Interrupt
MUX
(PAMOD)
PACNT
PTn
Edge detector
16-bit Main Timer
TCn Input Capture Reg.
Set CnF Interrupt
Chapter 13 Timer Module (TIM16B8CV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
416 Freescale Semiconductor
Figure 13-4. Channel 7 Output Compare/Pulse Accumulator Logic
NOTE
For more information see the respective functional descriptions in
Section 13.4, “Functional Description, of this document.
13.2 External Signal Description
The TIM16B8CV1 module has a total of eight external pins.
13.2.1 IOC7 — Input Capture and Output Compare Channel 7 Pin
This pin serves as input capture or output compare for channel 7. This can also be configured as pulse
accumulator input.
13.2.2 IOC6 — Input Capture and Output Compare Channel 6 Pin
This pin serves as input capture or output compare for channel 6.
13.2.3 IOC5 — Input Capture and Output Compare Channel 5 Pin
This pin serves as input capture or output compare for channel 5.
13.2.4 IOC4 — Input Capture and Output Compare Channel 4 Pin
This pin serves as input capture or output compare for channel 4. Pin
13.2.5 IOC3 — Input Capture and Output Compare Channel 3 Pin
This pin serves as input capture or output compare for channel 3.
PULSE
ACCUMULATOR PAD
OM7
OL7
OC7M7
CHANNEL 7 OUTPUT COMPARE
Chapter 13 Timer Module (TIM16B8CV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 417
13.2.6 IOC2 — Input Capture and Output Compare Channel 2 Pin
This pin serves as input capture or output compare for channel 2.
13.2.7 IOC1 — Input Capture and Output Compare Channel 1 Pin
This pin serves as input capture or output compare for channel 1.
13.2.8 IOC0 — Input Capture and Output Compare Channel 0 Pin
This pin serves as input capture or output compare for channel 0.
NOTE
For the description of interrupts see Section 13.6, “Interrupts”.
13.3 Memory Map and Register Definition
This section provides a detailed description of all memory and registers.
13.3.1 Module Memory Map
The memory map for the TIM16B8CV1 module is given below in Table 13-2. The address listed for each
register is the address offset. The total address for each register is the sum of the base address for the
TIM16B8CV1 module and the address offset for each register.
Chapter 13 Timer Module (TIM16B8CV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
418 Freescale Semiconductor
Table 13-2. TIM16B8CV1 Memory Map
Address Offset Use Access
0x0000 Timer Input Capture/Output Compare Select (TIOS) R/W
0x0001 Timer Compare Force Register (CFORC) R/W1
1 Always read 0x0000.
0x0002 Output Compare 7 Mask Register (OC7M) R/W
0x0003 Output Compare 7 Data Register (OC7D) R/W
0x0004 Timer Count Register (TCNT(hi)) R/W2
2Only writable in special modes (test_mode = 1).
0x0005 Timer Count Register (TCNT(lo)) R/W2
0x0006 Timer System Control Register1 (TSCR1) R/W
0x0007 Timer Toggle Overflow Register (TTOV) R/W
0x0008 Timer Control Register1 (TCTL1) R/W
0x0009 Timer Control Register2 (TCTL2) R/W
0x000A Timer Control Register3 (TCTL3) R/W
0x000B Timer Control Register4 (TCTL4) R/W
0x000C Timer Interrupt Enable Register (TIE) R/W
0x000D Timer System Control Register2 (TSCR2) R/W
0x000E Main Timer Interrupt Flag1 (TFLG1) R/W
0x000F Main Timer Interrupt Flag2 (TFLG2) R/W
0x0010 Timer Input Capture/Output Compare Register 0 (TC0(hi)) R/W3
3Write to these registers have no meaning or effect during input capture.
0x0011 Timer Input Capture/Output Compare Register 0 (TC0(lo)) R/W3
0x0012 Timer Input Capture/Output Compare Register 1 (TC1(hi)) R/W3
0x0013 Timer Input Capture/Output Compare Register 1 (TC1(lo)) R/W3
0x0014 Timer Input Capture/Output Compare Register 2 (TC2(hi)) R/W3
0x0015 Timer Input Capture/Output Compare Register 2 (TC2(lo)) R/W3
0x0016 Timer Input Capture/Output Compare Register 3 (TC3(hi)) R/W3
0x0017 Timer Input Capture/Output Compare Register 3 (TC3(lo)) R/W3
0x0018 Timer Input Capture/Output Compare Register4 (TC4(hi)) R/W3
0x0019 Timer Input Capture/Output Compare Register 4 (TC4(lo)) R/W3
0x001A Timer Input Capture/Output Compare Register 5 (TC5(hi)) R/W3
0x001B Timer Input Capture/Output Compare Register 5 (TC5(lo)) R/W3
0x001C Timer Input Capture/Output Compare Register 6 (TC6(hi)) R/W3
0x001D Timer Input Capture/Output Compare Register 6 (TC6(lo)) R/W3
0x001E Timer Input Capture/Output Compare Register 7 (TC7(hi)) R/W3
0x001F Timer Input Capture/Output Compare Register 7 (TC7(lo)) R/W3
0x0020 16-Bit Pulse Accumulator Control Register (PACTL) R/W
0x0021 Pulse Accumulator Flag Register (PAFLG) R/W
0x0022 Pulse Accumulator Count Register (PACNT(hi)) R/W
0x0023 Pulse Accumulator Count Register (PACNT(lo)) R/W
0x0024 – 0x002C Reserved 4
0x002D Timer Test Register (TIMTST) R/W2
0x002E – 0x002F Reserved 4
Chapter 13 Timer Module (TIM16B8CV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 419
13.3.2 Register Descriptions
This section consists of register descriptions in address order. Each description includes a standard
register diagram with an associated figure number. Details of register bit and field function follow the
register diagrams, in bit order.
4Write has no effect; return 0 on read
Register
Name Bit 7 654321Bit 0
0x0000
TIOS RIOS7 IOS6 IOS5 IOS4 IOS3 IOS2 IOS1 IOS0
W
0x0001
CFORC R00000000
W FOC7 FOC6 FOC5 FOC4 FOC3 FOC2 FOC1 FOC0
0x0002
OC7M ROC7M7 OC7M6 OC7M5 OC7M4 OC7M3 OC7M2 OC7M1 OC7M0
W
0x0003
OC7D ROC7D7 OC7D6 OC7D5 OC7D4 OC7D3 OC7D2 OC7D1 OC7D0
W
0x0004
TCNTH RTCNT15 TCNT14 TCNT13 TCNT12 TCNT11 TCNT10 TCNT9 TCNT8
W
0x0005
TCNTL RTCNT7 TCNT6 TCNT5 TCNT4 TCNT3 TCNT2 TCNT1 TCNT0
W
0x0006
TSCR1 RTEN TSWAI TSFRZ TFFCA 0000
W
0x0007
TTOV RTOV7 TOV6 TOV5 TOV4 TOV3 TOV2 TOV1 TOV0
W
0x0008
TCTL1 ROM7 OL7 OM6 OL6 OM5 OL5 OM4 OL4
W
0x0009
TCTL2 ROM3 OL3 OM2 OL2 OM1 OL1 OM0 OL0
W
0x000A
TCTL3 REDG7B EDG7A EDG6B EDG6A EDG5B EDG5A EDG4B EDG4A
W
0x000B
TCTL4 REDG3B EDG3A EDG2B EDG2A EDG1B EDG1A EDG0B EDG0A
W
= Unimplemented or Reserved
Figure 13-5. TIM16B8CV1 Register Summary
Chapter 13 Timer Module (TIM16B8CV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
420 Freescale Semiconductor
13.3.2.1 Timer Input Capture/Output Compare Select (TIOS)
0x000C
TIE RC7I C6I C5I C4I C3I C2I C1I C0I
W
0x000D
TSCR2 RTOI 000
TCRE PR2 PR1 PR0
W
0x000E
TFLG1 RC7F C6F C5F C4F C3F C2F C1F C0F
W
0x000F
TFLG2 RTOF 0000000
W
0x0010–0x001F
TCxH–TCxL
RBit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8
W
RBit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
W
0x0020
PACTL R0 PAEN PAMOD PEDGE CLK1 CLK0 PAOVI PAI
W
0x0021
PAFLG R000000
PAOVF PAIF
W
0x0022
PACNTH RPACNT15 PACNT14 PACNT13 PACNT12 PACNT11 PACNT10 PACNT9 PACNT8
W
0x0023
PACNTL RPACNT7 PACNT6 PACNT5 PACNT4 PACNT3 PACNT2 PACNT1 PACNT0
W
0x0024–0x002F
Reserved R
W
Module Base + 0x0000
76543210
RIOS7 IOS6 IOS5 IOS4 IOS3 IOS2 IOS1 IOS0
W
Reset 0 0 0 00000
Figure 13-6. Timer Input Capture/Output Compare Select (TIOS)
Register
Name Bit 7 654321Bit 0
= Unimplemented or Reserved
Figure 13-5. TIM16B8CV1 Register Summary (continued)
Chapter 13 Timer Module (TIM16B8CV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 421
Read: Anytime
Write: Anytime
13.3.2.2 Timer Compare Force Register (CFORC)
Read: Anytime but will always return 0x0000 (1 state is transient)
Write: Anytime
13.3.2.3 Output Compare 7 Mask Register (OC7M)
Read: Anytime
Write: Anytime
Table 13-3. TIOS Field Descriptions
Field Description
7:0
IOS[7:0] Input Capture or Output Compare Channel Configuration
0 The corresponding channel acts as an input capture.
1 The corresponding channel acts as an output compare.
Module Base + 0x0001
76543210
R00000000
W FOC7 FOC6 FOC5 FOC4 FOC3 FOC2 FOC1 FOC0
Reset 0 0 0 00000
Figure 13-7. Timer Compare Force Register (CFORC)
Table 13-4. CFORC Field Descriptions
Field Description
7:0
FOC[7:0] Force Output Compare Action for Channel 7:0 A write to this register with the corresponding data bit(s) set
causes the action which is programmed for output compare “x” to occur immediately. The action taken is the
same as if a successful comparison had just taken place with the TCx register except the interrupt flag does not
get set.
Note: A successful channel 7 output compare overrides any channel 6:0 compares. If forced output compare on
any channel occurs at the same time as the successful output compare then forced output compare action
will take precedence and interrupt flag won’t get set.
Module Base + 0x0002
76543210
ROC7M7 OC7M6 OC7M5 OC7M4 OC7M3 OC7M2 OC7M1 OC7M0
W
Reset 0 0 0 00000
Figure 13-8. Output Compare 7 Mask Register (OC7M)
Chapter 13 Timer Module (TIM16B8CV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
422 Freescale Semiconductor
13.3.2.4 Output Compare 7 Data Register (OC7D)
Read: Anytime
Write: Anytime
13.3.2.5 Timer Count Register (TCNT)
Table 13-5. OC7M Field Descriptions
Field Description
7:0
OC7M[7:0] Output Compare 7 Mask Setting the OC7Mx (x ranges from 0 to 6) will set the corresponding port to be an
output port when the corresponding TIOSx (x ranges from 0 to 6) bit is set to be an output compare.
Note: A successful channel 7 output compare overrides any channel 6:0 compares. For each OC7M bit that is
set, the output compare action reflects the corresponding OC7D bit.
Module Base + 0x0003
76543210
ROC7D7 OC7D6 OC7D5 OC7D4 OC7D3 OC7D2 OC7D1 OC7D0
W
Reset 0 0 0 00000
Figure 13-9. Output Compare 7 Data Register (OC7D)
Table 13-6. OC7D Field Descriptions
Field Description
7:0
OC7D[7:0] Output Compare 7 Data — A channel 7 output compare can cause bits in the output compare 7 data register
to transfer to the timer port data register depending on the output compare 7 mask register.
Module Base + 0x0004
15 14 13 12 11 10 9 9
RTCNT15 TCNT14 TCNT13 TCNT12 TCNT11 TCNT10 TCNT9 TCNT8
W
Reset 0 0 0 00000
Figure 13-10. Timer Count Register High (TCNTH)
Module Base + 0x0005
76543210
RTCNT7 TCNT6 TCNT5 TCNT4 TCNT3 TCNT2 TCNT1 TCNT0
W
Reset 0 0 0 00000
Figure 13-11. Timer Count Register Low (TCNTL)
Chapter 13 Timer Module (TIM16B8CV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 423
The 16-bit main timer is an up counter.
A full access for the counter register should take place in one clock cycle. A separate read/write for high
byte and low byte will give a different result than accessing them as a word.
Read: Anytime
Write: Has no meaning or effect in the normal mode; only writable in special modes (test_mode = 1).
The period of the first count after a write to the TCNT registers may be a different size because the write
is not synchronized with the prescaler clock.
13.3.2.6 Timer System Control Register 1 (TSCR1)
Read: Anytime
Write: Anytime
Module Base + 0x0006
76543210
RTEN TSWAI TSFRZ TFFCA 0000
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 13-12. Timer System Control Register 1 (TSCR1)
Table 13-7. TSCR1 Field Descriptions
Field Description
7
TEN Timer Enable
0 Disables the main timer, including the counter. Can be used for reducing power consumption.
1 Allows the timer to function normally.
If for any reason the timer is not active, there is no ÷64 clock for the pulse accumulator because the ÷64 is
generated by the timer prescaler.
6
TSWAI Timer Module Stops While in Wait
0 Allows the timer module to continue running during wait.
1 Disables the timer module when the MCU is in the wait mode. Timer interrupts cannot be used to get the MCU
out of wait.
TSWAI also affects pulse accumulator.
Chapter 13 Timer Module (TIM16B8CV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
424 Freescale Semiconductor
13.3.2.7 Timer Toggle On Overflow Register 1 (TTOV)
Read: Anytime
Write: Anytime
13.3.2.8 Timer Control Register 1/Timer Control Register 2 (TCTL1/TCTL2)
5
TSFRZ Timer Stops While in Freeze Mode
0 Allows the timer counter to continue running while in freeze mode.
1 Disables the timer counter whenever the MCU is in freeze mode. This is useful for emulation.
TSFRZ does not stop the pulse accumulator.
4
TFFCA Timer Fast Flag Clear All
0 Allows the timer flag clearing to function normally.
1 For TFLG1(0x000E), a read from an input capture or a write to the output compare channel (0x0010–0x001F)
causes the corresponding channel flag, CnF, to be cleared. For TFLG2 (0x000F), any access to the TCNT
register (0x0004, 0x0005) clears the TOF flag. Any access to the PACNT registers (0x0022, 0x0023) clears
the PAOVF and PAIF flags in the PAFLG register (0x0021). This has the advantage of eliminating software
overhead in a separate clear sequence. Extra care is required to avoid accidental flag clearing due to
unintended accesses.
Module Base + 0x0007
76543210
RTOV7 TOV6 TOV5 TOV4 TOV3 TOV2 TOV1 TOV0
W
Reset 0 0 0 00000
Figure 13-13. Timer Toggle On Overflow Register 1 (TTOV)
Table 13-8. TTOV Field Descriptions
Field Description
7:0
TOV[7:0] Toggle On Overflow Bits TOVx toggles output compare pin on overflow. This feature only takes effect when
in output compare mode. When set, it takes precedence over forced output compare but not channel 7 override
events.
0 Toggle output compare pin on overflow feature disabled.
1 Toggle output compare pin on overflow feature enabled.
Module Base + 0x0008
76543210
ROM7 OL7 OM6 OL6 OM5 OL5 OM4 OL4
W
Reset 0 0 0 00000
Figure 13-14. Timer Control Register 1 (TCTL1)
Table 13-7. TSCR1 Field Descriptions (continued)
Field Description
Chapter 13 Timer Module (TIM16B8CV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 425
Read: Anytime
Write: Anytime
To operate the 16-bit pulse accumulator independently of input capture or output compare 7 and 0
respectively the user must set the corresponding bits IOSx = 1, OMx = 0 and OLx = 0. OC7M7 in the
OC7M register must also be cleared.
To enable output action using the OM7 and OL7 bits on the timer port,the corresponding bit OC7M7 in
the OC7M register must also be cleared. The settings for these bits can be seen in Table 13-11
Table 13-11. The OC7 and OCx event priority
Module Base + 0x0009
76543210
ROM3 OL3 OM2 OL2 OM1 OL1 OM0 OL0
W
Reset 0 0 0 00000
Figure 13-15. Timer Control Register 2 (TCTL2)
Table 13-9. TCTL1/TCTL2 Field Descriptions
Field Description
7:0
OMx Output Mode These eight pairs of control bits are encoded to specify the output action to be taken as a result
of a successful OCx compare. When either OMx or OLx is 1, the pin associated with OCx becomes an output
tied to OCx.
Note: To enable output action by OMx bits on timer port, the corresponding bit in OC7M should be cleared.
7:0
OLx Output Level These eight pairs of control bits are encoded to specify the output action to be taken as a result
of a successful OCx compare. When either OMx or OLx is 1, the pin associated with OCx becomes an output
tied to OCx.
Note: To enable output action by OLx bits on timer port, the corresponding bit in OC7M should be cleared.
Table 13-10. Compare Result Output Action
OMx OLx Action
0 0 Timer disconnected from output pin logic
0 1 Toggle OCx output line
1 0 Clear OCx output line to zero
1 1 Set OCx output line to one
OC7M7=0 OC7M7=1
OC7Mx=1 OC7Mx=0 OC7Mx=1 OC7Mx=0
TC7=TCx TC7>TCx TC7=TCx TC7>TCx TC7=TCx TC7>TCx TC7=TCx TC7>TCx
IOCx=OC7Dx
IOC7=OM7/O
L7
IOCx=OC7Dx
+OMx/OLx
IOC7=OM7/O
L7
IOCx=OMx/OLx
IOC7=OM7/OL7 IOCx=OC7Dx
IOC7=OC7D7 IOCx=OC7Dx
+OMx/OLx
IOC7=OC7D7
IOCx=OMx/OLx
IOC7=OC7D7
Chapter 13 Timer Module (TIM16B8CV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
426 Freescale Semiconductor
Note: in Table 13-11, the IOS7 and IOSx should be set to 1
IOSx is the register TIOS bit x,
OC7Mx is the register OC7M bit x,
TCx is timer Input Capture/Output Compare register,
IOCx is channel x,
OMx/OLx is the register TCTL1/TCTL2,
OC7Dx is the register OC7D bit x.
IOCx = OC7Dx+ OMx/OLx, means that both OC7 event and OCx event will change channel x value.
Chapter 13 Timer Module (TIM16B8CV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 427
13.3.2.9 Timer Control Register 3/Timer Control Register 4 (TCTL3 and TCTL4)
Read: Anytime
Write: Anytime.
Module Base + 0x000A
76543210
REDG7B EDG7A EDG6B EDG6A EDG5B EDG5A EDG4B EDG4A
W
Reset 0 0 0 00000
Figure 13-16. Timer Control Register 3 (TCTL3)
Module Base + 0x000B
76543210
REDG3B EDG3A EDG2B EDG2A EDG1B EDG1A EDG0B EDG0A
W
Reset 0 0 0 00000
Figure 13-17. Timer Control Register 4 (TCTL4)
Table 13-12. TCTL3/TCTL4 Field Descriptions
Field Description
7:0
EDGnB
EDGnA
Input Capture Edge Control — These eight pairs of control bits configure the input capture edge detector
circuits.
Table 13-13. Edge Detector Circuit Configuration
EDGnB EDGnA Configuration
0 0 Capture disabled
0 1 Capture on rising edges only
1 0 Capture on falling edges only
1 1 Capture on any edge (rising or falling)
Chapter 13 Timer Module (TIM16B8CV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
428 Freescale Semiconductor
13.3.2.10 Timer Interrupt Enable Register (TIE)
Read: Anytime
Write: Anytime.
13.3.2.11 Timer System Control Register 2 (TSCR2)
Read: Anytime
Write: Anytime.
Module Base + 0x000C
76543210
RC7I C6I C5I C4I C3I C2I C1I C0I
W
Reset 0 0 0 00000
Figure 13-18. Timer Interrupt Enable Register (TIE)
Table 13-14. TIE Field Descriptions
Field Description
7:0
C7I:C0I Input Capture/Output Compare “x” Interrupt Enable — The bits in TIE correspond bit-for-bit with the bits in
the TFLG1 status register. If cleared, the corresponding flag is disabled from causing a hardware interrupt. If set,
the corresponding flag is enabled to cause a interrupt.
Module Base + 0x000D
76543210
RTOI 000
TCRE PR2 PR1 PR0
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 13-19. Timer System Control Register 2 (TSCR2)
Chapter 13 Timer Module (TIM16B8CV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 429
NOTE
The newly selected prescale factor will not take effect until the next
synchronized edge where all prescale counter stages equal zero.
13.3.2.12 Main Timer Interrupt Flag 1 (TFLG1)
Read: Anytime
Table 13-15. TSCR2 Field Descriptions
Field Description
7
TOI Timer Overflow Interrupt Enable
0 Interrupt inhibited.
1 Hardware interrupt requested when TOF flag set.
3
TCRE Timer Counter Reset Enable This bit allows the timer counter to be reset by a successful output compare 7
event. This mode of operation is similar to an up-counting modulus counter.
0 Counter reset inhibited and counter free runs.
1 Counter reset by a successful output compare 7.
Note: If TC7 = 0x0000 and TCRE = 1, TCNT will stay at 0x0000 continuously. If TC7 = 0xFFFF and TCRE = 1,
TOF will never be set when TCNT is reset from 0xFFFF to 0x0000.
Note: TCRE=1 and TC7!=0, the TCNT cycle period will be TC7 x "prescaler counter width" + "1 Bus Clock", for
a more detail explanation please refer to Section 13.4.3, “Output Compare
2
PR[2:0] Timer Prescaler Select — These three bits select the frequency of the timer prescaler clock derived from the
Bus Clock as shown in Table 13-16.
Table 13-16. Timer Clock Selection
PR2 PR1 PR0 Timer Clock
0 0 0 Bus Clock / 1
0 0 1 Bus Clock / 2
0 1 0 Bus Clock / 4
0 1 1 Bus Clock / 8
1 0 0 Bus Clock / 16
1 0 1 Bus Clock / 32
1 1 0 Bus Clock / 64
1 1 1 Bus Clock / 128
Module Base + 0x000E
76543210
RC7F C6F C5F C4F C3F C2F C1F C0F
W
Reset 0 0 0 00000
Figure 13-20. Main Timer Interrupt Flag 1 (TFLG1)
Chapter 13 Timer Module (TIM16B8CV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
430 Freescale Semiconductor
Write: Used in the clearing mechanism (set bits cause corresponding bits to be cleared). Writing a zero
will not affect current status of the bit.
13.3.2.13 Main Timer Interrupt Flag 2 (TFLG2)
TFLG2 indicates when interrupt conditions have occurred. To clear a bit in the flag register, write the bit
to one while TEN of TSCR1 is set to one.
Read: Anytime
Write: Used in clearing mechanism (set bits cause corresponding bits to be cleared).
Any access to TCNT will clear TFLG2 register if the TFFCA bit in TSCR register is set.
Table 13-17. TRLG1 Field Descriptions
Field Description
7:0
C[7:0]F Input Capture/Output Compare Channel “x” Flag — These flags are set when an input capture or output
compare event occurs. Clearing requires writing a one to the corresponding flag bit when TEN is set to one.
When TFFCA bit in TSCR register is set, a read from an input capture or a write into an output compare channel
(0x0010–0x001F) will cause the corresponding channel flag CxF to be cleared.
Module Base + 0x000F
76543210
RTOF 0000000
W
Reset 0 0 0 00000
Unimplemented or Reserved
Figure 13-21. Main Timer Interrupt Flag 2 (TFLG2)
Table 13-18. TRLG2 Field Descriptions
Field Description
7
TOF Timer Overflow Flag Set when 16-bit free-running timer overflows from 0xFFFF to 0x0000. Clearing this bit
requires writing a one to bit 7 of TFLG2 register while TEN bit of TSCR1 is set to one. (See also TCRE control
bit explanation.)
Chapter 13 Timer Module (TIM16B8CV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 431
13.3.2.14 Timer Input Capture/Output Compare Registers High and Low 0–7
(TCxH and TCxL)
Depending on the TIOS bit for the corresponding channel, these registers are used to latch the value of the
free-running counter when a defined transition is sensed by the corresponding input capture edge detector
or to trigger an output action for output compare.
Read: Anytime
Write: Anytime for output compare function.Writes to these registers have no meaning or effect during
input capture. All timer input capture/output compare registers are reset to 0x0000.
NOTE
Read/Write access in byte mode for high byte should takes place before low
byte otherwise it will give a different result.
Module Base + 0x0010 = TC0H
0x0012 = TC1H
0x0014 = TC2H
0x0016 = TC3H
0x0018 = TC4H
0x001A = TC5H
0x001C = TC6H
0x001E = TC7H
15 14 13 12 11 10 9 0
RBit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8
W
Reset 00000000
Figure 13-22. Timer Input Capture/Output Compare Register x High (TCxH)
Module Base + 0x0011 = TC0L
0x0013 = TC1L
0x0015 = TC2L
0x0017 = TC3L
0x0019 = TC4L
0x001B = TC5L
0x001D = TC6L
0x001F = TC7L
76543210
RBit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
W
Reset 00000000
Figure 13-23. Timer Input Capture/Output Compare Register x Low (TCxL)
Chapter 13 Timer Module (TIM16B8CV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
432 Freescale Semiconductor
13.3.2.15 16-Bit Pulse Accumulator Control Register (PACTL)
When PAEN is set, the PACT is enabled.The PACT shares the input pin with IOC7.
Read: Any time
Write: Any time
Module Base + 0x0020
76543210
R0 PAEN PAMOD PEDGE CLK1 CLK0 PAOVI PAI
W
Reset 0 0 0 00000
Unimplemented or Reserved
Figure 13-24. 16-Bit Pulse Accumulator Control Register (PACTL)
Table 13-19. PACTL Field Descriptions
Field Description
6
PAEN Pulse Accumulator System Enable — PAEN is independent from TEN. With timer disabled, the pulse
accumulator can function unless pulse accumulator is disabled.
0 16-Bit Pulse Accumulator system disabled.
1 Pulse Accumulator system enabled.
5
PAMOD Pulse Accumulator Mode — This bit is active only when the Pulse Accumulator is enabled (PAEN = 1). See
Table 13-20.
0 Event counter mode.
1 Gated time accumulation mode.
4
PEDGE Pulse Accumulator Edge Control This bit is active only when the Pulse Accumulator is enabled (PAEN = 1).
For PAMOD bit = 0 (event counter mode). See Table 13-20.
0 Falling edges on IOC7 pin cause the count to be incremented.
1 Rising edges on IOC7 pin cause the count to be incremented.
For PAMOD bit = 1 (gated time accumulation mode).
0 IOC7 input pin high enables M (bus clock) divided by 64 clock to Pulse Accumulator and the trailing falling
edge on IOC7 sets the PAIF flag.
1 IOC7 input pin low enables M (bus clock) divided by 64 clock to Pulse Accumulator and the trailing rising edge
on IOC7 sets the PAIF flag.
3:2
CLK[1:0] Clock Select Bits — Refer to Table 13-21.
1
PAOVI Pulse Accumulator Overflow Interrupt Enable
0 Interrupt inhibited.
1 Interrupt requested if PAOVF is set.
0
PAI Pulse Accumulator Input Interrupt Enable
0 Interrupt inhibited.
1 Interrupt requested if PAIF is set.
Chapter 13 Timer Module (TIM16B8CV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 433
NOTE
If the timer is not active (TEN = 0 in TSCR), there is no divide-by-64
because the ÷64 clock is generated by the timer prescaler.
For the description of PACLK please refer Figure 13-24.
If the pulse accumulator is disabled (PAEN = 0), the prescaler clock from the timer is always used as an
input clock to the timer counter. The change from one selected clock to the other happens immediately
after these bits are written.
13.3.2.16 Pulse Accumulator Flag Register (PAFLG)
Read: Anytime
Write: Anytime
When the TFFCA bit in the TSCR register is set, any access to the PACNT register will clear all the flags
in the PAFLG register. Timer module must stay enabled (TEN =1) while clearing thse bits.
Table 13-20. Pin Action
PAMOD PEDGE Pin Action
0 0 Falling edge
0 1 Rising edge
1 0 Div. by 64 clock enabled with pin high level
1 1 Div. by 64 clock enabled with pin low level
Table 13-21. Timer Clock Selection
CLK1 CLK0 Timer Clock
0 0 Use timer prescaler clock as timer counter clock
0 1 Use PACLK as input to timer counter clock
1 0 Use PACLK/256 as timer counter clock frequency
1 1 Use PACLK/65536 as timer counter clock frequency
Module Base + 0x0021
76543210
R000000
PAOVF PAIF
W
Reset 0 0 0 00000
Unimplemented or Reserved
Figure 13-25. Pulse Accumulator Flag Register (PAFLG)
Chapter 13 Timer Module (TIM16B8CV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
434 Freescale Semiconductor
Table 13-22. PAFLG Field Descriptions
Field Description
1
PAOVF Pulse Accumulator Overflow Flag Set when the 16-bit pulse accumulator overflows from 0xFFFF to 0x0000.
Clearing this bit requires wirting a one to this bit in the PAFLG register while TEN bit of TSCR1 register is set to
one.
0
PAIF Pulse Accumulator Input edge Flag Set when the selected edge is detected at the IOC7 input pin.In event
mode the event edge triggers PAIF and in gated time accumulation mode the trailing edge of the gate signal at
the IOC7 input pin triggers PAIF.
Clearing this bit requires writing a one to this bit in the PAFLG register while TEN bit of TSCR1 register is set to
one. Any access to the PACNT register will clear all the flags in this register when TFFCA bit in register
TSCR(0x0006) is set.
Chapter 13 Timer Module (TIM16B8CV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 435
13.3.2.17 Pulse Accumulators Count Registers (PACNT)
Read: Anytime
Write: Anytime
These registers contain the number of active input edges on its input pin since the last reset.
When PACNT overflows from 0xFFFF to 0x0000, the Interrupt flag PAOVF in PAFLG (0x0021) is set.
Full count register access should take place in one clock cycle. A separate read/write for high byte and low
byte will give a different result than accessing them as a word.
NOTE
Reading the pulse accumulator counter registers immediately after an active
edge on the pulse accumulator input pin may miss the last count because the
input has to be synchronized with the bus clock first.
13.4 Functional Description
This section provides a complete functional description of the timer TIM16B8CV1 block. Please refer to
the detailed timer block diagram in Figure 13-28 as necessary.
Module Base + 0x0022
15 14 13 12 11 10 9 0
RPACNT15 PACNT14 PACNT13 PACNT12 PACNT11 PACNT10 PACNT9 PACNT8
W
Reset 0 0 0 00000
Figure 13-26. Pulse Accumulator Count Register High (PACNTH)
Module Base + 0x0023
76543210
RPACNT7 PACNT6 PACNT5 PACNT4 PACNT3 PACNT2 PACNT1 PACNT0
W
Reset 0 0 0 00000
Figure 13-27. Pulse Accumulator Count Register Low (PACNTL)
Chapter 13 Timer Module (TIM16B8CV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
436 Freescale Semiconductor
Figure 13-28. Detailed Timer Block Diagram
13.4.1 Prescaler
The prescaler divides the bus clock by 1,2,4,8,16,32,64 or 128. The prescaler select bits, PR[2:0], select
the prescaler divisor. PR[2:0] are in timer system control register 2 (TSCR2).
PRESCALER
CHANNEL 0
IOC0 PIN
16-BIT COUNTER
LOGIC
PR[2:1:0]
DIVIDE-BY-64
TC0
EDGE
DETECT
PACNT(hi):PACNT(lo)
PAOVF PEDGE
PAOVI
TEN
PAE
16-BIT COMPARATOR
TCNT(hi):TCNT(lo)
CHANNEL 1
TC1
16-BIT COMPARATOR
16-BIT COUNTER
INTERRUPT
LOGIC
TOF
TOI
C0F
C1F
EDGE
DETECT
IOC1 PIN
LOGIC
EDGE
DETECT
CxF
CHANNEL7
TC7
16-BIT COMPARATOR C7F
IOC7 PIN
LOGIC
EDGE
DETECT
OM:OL0
TOV0
OM:OL1
TOV1
OM:O73
TOV7
EDG1A EDG1B
EDG7A
EDG7B
EDG0B
TCRE
PAIF
CLEAR COUNTER
PAIF
PAI
INTERRUPT
LOGIC
CxI
INTERRUPT
REQUEST
PAOVF
CH. 7 COMPARE
CH.7 CAPTURE
CH. 1 CAPTURE
MUX
CLK[1:0]
PACLK
PACLK/256
PACLK/65536
IOC1 PIN
IOC0 PIN
IOC7 PIN
PACLK
PACLK/256
PACLK/65536
TE
CH. 1 COMPARE
CH. 0COMPARE
CH. 0 CAPTURE
PA INPUT
CHANNEL2
EDG0A
channel 7 output
compare
IOC0
IOC1
IOC7
Bus Clock
Bus Clock
PAOVF
PAOVI
TOF
C0F
C1F
C7F
Chapter 13 Timer Module (TIM16B8CV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 437
13.4.2 Input Capture
Clearing the I/O (input/output) select bit, IOSx, configures channel x as an input capture channel. The
input capture function captures the time at which an external event occurs. When an active edge occurs on
the pin of an input capture channel, the timer transfers the value in the timer counter into the timer channel
registers, TCx.
The minimum pulse width for the input capture input is greater than two bus clocks.
An input capture on channel x sets the CxF flag. The CxI bit enables the CxF flag to generate interrupt
requests. Timer module must stay enabled (TEN bit of TSCR1 must be set to one) while clearing CxF
(writing one to CxF).
13.4.3 Output Compare
Setting the I/O select bit, IOSx, configures channel x as an output compare channel. The output compare
function can generate a periodic pulse with a programmable polarity, duration, and frequency. When the
timer counter reaches the value in the channel registers of an output compare channel, the timer can set,
clear, or toggle the channel pin. An output compare on channel x sets the CxF flag. The CxI bit enables the
CxF flag to generate interrupt requests. Timer module must stay enabled (TEN bit of TSCR1 register must
be set to one) while clearing CxF (writing one to CxF).
The output mode and level bits, OMx and OLx, select set, clear, toggle on output compare. Clearing both
OMx and OLx disconnects the pin from the output logic.
Setting a force output compare bit, FOCx, causes an output compare on channel x. A forced output
compare does not set the channel flag.
A successful output compare on channel 7 overrides output compares on all other output compare
channels. The output compare 7 mask register masks the bits in the output compare 7 data register. The
timer counter reset enable bit, TCRE, enables channel 7 output compares to reset the timer counter. A
channel 7 output compare can reset the timer counter even if the IOC7 pin is being used as the pulse
accumulator input.
Writing to the timer port bit of an output compare pin does not affect the pin state. The value written is
stored in an internal latch. When the pin becomes available for general-purpose output, the last value
written to the bit appears at the pin.
When TCRE is set and TC7 is not equal to 0, then TCNT will cycle from 0 to TC7. When TCNT reaches
TC7 value, it will last only one bus cycle then reset to 0.
Chapter 13 Timer Module (TIM16B8CV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
438 Freescale Semiconductor
Note: in Figure 13-29,if PR[2:0] is equal to 0, one prescaler counter equal to one bus clock
Figure 13-29. The TCNT cycle diagram under TCRE=1 condition
13.4.4 Pulse Accumulator
The pulse accumulator (PACNT) is a 16-bit counter that can operate in two modes:
Event counter mode — Counting edges of selected polarity on the pulse accumulator input pin, PAI.
Gated time accumulation mode Counting pulses from a divide-by-64 clock. The PAMOD bit selects the
mode of operation.
The minimum pulse width for the PAI input is greater than two bus clocks.
13.4.5 Event Counter Mode
Clearing the PAMOD bit configures the PACNT for event counter operation. An active edge on the IOC7
pin increments the pulse accumulator counter. The PEDGE bit selects falling edges or rising edges to
increment the count.
NOTE
The PACNT input and timer channel 7 use the same pin IOC7. To use the
IOC7, disconnect it from the output logic by clearing the channel 7 output
mode and output level bits, OM7 and OL7. Also clear the channel 7 output
compare 7 mask bit, OC7M7.
The Pulse Accumulator counter register reflect the number of active input edges on the PACNT input pin
since the last reset.
The PAOVF bit is set when the accumulator rolls over from 0xFFFF to 0x0000. The pulse accumulator
overflow interrupt enable bit, PAOVI, enables the PAOVF flag to generate interrupt requests.
NOTE
The pulse accumulator counter can operate in event counter mode even
when the timer enable bit, TEN, is clear.
TC7 01----- TC7-1 TC7 0
TC7 event TC7 event
prescaler
counter 1 bus
clock
Chapter 13 Timer Module (TIM16B8CV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 439
13.4.6 Gated Time Accumulation Mode
Setting the PAMOD bit configures the pulse accumulator for gated time accumulation operation. An active
level on the PACNT input pin enables a divided-by-64 clock to drive the pulse accumulator. The PEDGE
bit selects low levels or high levels to enable the divided-by-64 clock.
The trailing edge of the active level at the IOC7 pin sets the PAIF. The PAI bit enables the PAIF flag to
generate interrupt requests.
The pulse accumulator counter register reflect the number of pulses from the divided-by-64 clock since the
last reset.
NOTE
The timer prescaler generates the divided-by-64 clock. If the timer is not
active, there is no divided-by-64 clock.
13.5 Resets
The reset state of each individual bit is listed within Section 13.3, “Memory Map and Register Definition”
which details the registers and their bit fields.
13.6 Interrupts
This section describes interrupts originated by the TIM16B8CV1 block. Table 13-23 lists the interrupts
generated by the TIM16B8CV1 to communicate with the MCU.
The TIM16B8CV1 uses a total of 11 interrupt vectors. The interrupt vector offsets and interrupt numbers
are chip dependent.
13.6.1 Channel [7:0] Interrupt (C[7:0]F)
This active high outputs will be asserted by the module to request a timer channel 7 – 0 interrupt to be
serviced by the system controller.
Table 13-23. TIM16B8CV1 Interrupts
Interrupt Offset1
1Chip Dependent.
Vector1Priority1Source Description
C[7:0]F Timer Channel 7–0 Active high timer channel interrupts 7–0
PAOVI Pulse Accumulator
Input Active high pulse accumulator input interrupt
PAOVF Pulse Accumulator
Overflow Pulse accumulator overflow interrupt
TOF Timer Overflow Timer Overflow interrupt
Chapter 13 Timer Module (TIM16B8CV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
440 Freescale Semiconductor
13.6.2 Pulse Accumulator Input Interrupt (PAOVI)
This active high output will be asserted by the module to request a timer pulse accumulator input interrupt
to be serviced by the system controller.
13.6.3 Pulse Accumulator Overflow Interrupt (PAOVF)
This active high output will be asserted by the module to request a timer pulse accumulator overflow
interrupt to be serviced by the system controller.
13.6.4 Timer Overflow Interrupt (TOF)
This active high output will be asserted by the module to request a timer overflow interrupt to be serviced
by the system controller.
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 441
Chapter 14
Dual Output Voltage Regulator (VREG3V3V2)
Block Description
14.1 Introduction
The VREG3V3V2 is a dual output voltage regulator providing two separate 2.5 V (typical) supplies
differing in the amount of current that can be sourced. The regulator input voltage range is from 3.3 V up
to 5 V (typical).
14.1.1 Features
The block VREG3V3V2 includes these distinctive features:
Two parallel, linear voltage regulators
Bandgap reference
Low-voltage detect (LVD) with low-voltage interrupt (LVI)
Power-on reset (POR)
Low-voltage reset (LVR)
14.1.2 Modes of Operation
There are three modes VREG3V3V2 can operate in:
Full-performance mode (FPM) (MCU is not in stop mode)
The regulator is active, providing the nominal supply voltage of 2.5 V with full current sourcing
capability at both outputs. Features LVD (low-voltage detect), LVR (low-voltage reset), and POR
(power-on reset) are available.
Reduced-power mode (RPM) (MCU is in stop mode)
The purpose is to reduce power consumption of the device. The output voltage may degrade to a
lower value than in full-performance mode, additionally the current sourcing capability is
substantially reduced. Only the POR is available in this mode, LVD and LVR are disabled.
Shutdown mode
Controlled by VREGEN (see device overview chapter for connectivity of VREGEN).
This mode is characterized by minimum power consumption. The regulator outputs are in a high
impedance state, only the POR feature is available, LVD and LVR are disabled.
This mode must be used to disable the chip internal regulator VREG3V3V2, i.e., to bypass the
VREG3V3V2 to use external supplies.
Chapter 14 Dual Output Voltage Regulator (VREG3V3V2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
442 Freescale Semiconductor
14.1.3 Block Diagram
Figure 14-1 shows the function principle of VREG3V3V2 by means of a block diagram. The regulator
core REG consists of two parallel sub-blocks, REG1 and REG2, providing two independent output
voltages.
Figure 14-1. VREG3V3 Block Diagram
LVR
LVD POR
VDDR
VDD
LVI
POR
LVR
CTRL
VSS
VDDPLL
VSSPLL
VREGEN
REG
REG2
REG1
PIN
VDDA
VSSA
REG: Regulator Core
LVD: Low Voltage Detect
CTRL: Regulator Control
LVR: Low Voltage Reset
POR: Power-on Reset
Chapter 14 Dual Output Voltage Regulator (VREG3V3V2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 443
14.2 External Signal Description
Due to the nature of VREG3V3V2 being a voltage regulator providing the chip internal power supply
voltages most signals are power supply signals connected to pads.
Table 14-1 shows all signals of VREG3V3V2 associated with pins.
NOTE
Check device overview chapter for connectivity of the signals.
14.2.1 VDDR — Regulator Power Input
Signal VDDR is the power input of VREG3V3V2. All currents sourced into the regulator loads flow
through this pin. A chip external decoupling capacitor (100 nF...220 nF, X7R ceramic) between VDDR and
VSSR can smoothen ripple on VDDR.
For entering shutdown mode, pin VDDR should also be tied to ground on devices without a VREGEN pin.
14.2.2 VDDA, VSSA — Regulator Reference Supply
Signals VDDA/VSSA which are supposed to be relatively quiet are used to supply the analog parts of the
regulator. Internal precision reference circuits are supplied from these signals. A chip external decoupling
capacitor (100 nF...220 nF, X7R ceramic) between VDDA and VSSA can further improve the quality of this
supply.
Table 14-1. VREG3V3V2 — Signal Properties
Name Port Function Reset State Pull Up
VDDR VREG3V3V2 power input (positive supply)
VDDA VREG3V3V2 quiet input (positive supply)
VSSA VREG3V3V2 quiet input (ground)
VDD VREG3V3V2 primary output (positive supply)
VSS VREG3V3V2 primary output (ground)
VDDPLL VREG3V3V2 secondary output (positive supply)
VSSPLL VREG3V3V2 secondary output (ground)
VREGEN (optional) VREG3V3V2 (Optional) Regulator Enable
Chapter 14 Dual Output Voltage Regulator (VREG3V3V2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
444 Freescale Semiconductor
14.2.3 VDD, VSS — Regulator Output1 (Core Logic)
Signals VDD/VSS are the primary outputs of VREG3V3V2 that provide the power supply for the core
logic. These signals are connected to device pins to allow external decoupling capacitors (100 nF...220 nF,
X7R ceramic).
In shutdown mode an external supply at VDD/VSS can replace the voltage regulator.
14.2.4 VDDPLL, VSSPLL — Regulator Output2 (PLL)
Signals VDDPLL/VSSPLL are the secondary outputs of VREG3V3V2 that provide the power supply for the
PLL and oscillator. These signals are connected to device pins to allow external decoupling capacitors
(100 nF...220 nF, X7R ceramic).
In shutdown mode an external supply at VDDPLL/VSSPLL can replace the voltage regulator.
14.2.5 VREGEN — Optional Regulator Enable
This optional signal is used to shutdown VREG3V3V2. In that case VDD/VSS and VDDPLL/VSSPLL must
be provided externally. shutdown mode is entered with VREGEN being low. If VREGEN is high, the
VREG3V3V2 is either in full-performance mode or in reduced-power mode.
For the connectivity of VREGEN see device overview chapter.
NOTE
Switching from FPM or RPM to shutdown of VREG3V3V2 and vice versa
is not supported while the MCU is powered.
14.3 Memory Map and Register Definition
This subsection provides a detailed description of all registers accessible in VREG3V3V2.
14.3.1 Module Memory Map
Figure 14-2 provides an overview of all used registers.
Table 14-2. VREG3V3V2 Memory Map
Address
Offset Use Access
0x0000 VREG3V3V2 Control Register (VREGCTRL) R/W
Chapter 14 Dual Output Voltage Regulator (VREG3V3V2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 445
14.3.2 Register Descriptions
The following paragraphs describe, in address order, all the VREG3V3V2 registers and their individual
bits.
14.3.2.1 VREG3V3V2 — Control Register (VREGCTRL)
The VREGCTRL register allows to separately enable features of VREG3V3V2.
NOTE
On entering the reduced-power mode the LVIF is not cleared by the
VREG3V3V2.
14.4 Functional Description
Block VREG3V3V2 is a voltage regulator as depicted in Figure 14-1. The regulator functional elements
are the regulator core (REG), a low-voltage detect module (LVD), a power-on reset module (POR) and a
low-voltage reset module (LVR). There is also the regulator control block (CTRL) which represents the
interface to the digital core logic but also manages the operating modes of VREG3V3V2.
Module Base + 0x0000
76543210
R00000LVDS
LVIE LVIF
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 14-2. VREG3V3 — Control Register (VREGCTRL)
Table 14-3. MCCTL1 Field Descriptions
Field Description
2
LVDS Low-Voltage Detect Status Bit — This read-only status bit reflects the input voltage. Writes have no effect.
0 Input voltage VDDA is above level VLVID or RPM or shutdown mode.
1 Input voltage VDDA is below level VLVIA and FPM.
1
LVIE Low-Voltage Interrupt Enable Bit
0 Interrupt request is disabled.
1 Interrupt will be requested whenever LVIF is set.
0
LVIF Low-Voltage Interrupt Flag LVIF is set to 1 when LVDS status bit changes. This flag can only be cleared by
writing a 1. Writing a 0 has no effect. If enabled (LVIE = 1), LVIF causes an interrupt request.
0 No change in LVDS bit.
1 LVDS bit has changed.
Chapter 14 Dual Output Voltage Regulator (VREG3V3V2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
446 Freescale Semiconductor
14.4.1 REG — Regulator Core
VREG3V3V2, respectively its regulator core has two parallel, independent regulation loops (REG1 and
REG2) that differ only in the amount of current that can be sourced to the connected loads. Therefore, only
REG1 providing the supply at VDD/VSS is explained. The principle is also valid for REG2.
The regulator is a linear series regulator with a bandgap reference in its full-performance mode and a
voltage clamp in reduced-power mode. All load currents flow from input VDDR to VSS or VSSPLL, the
reference circuits are connected to VDDA and VSSA.
14.4.2 Full-Performance Mode
In full-performance mode, a fraction of the output voltage (VDD) and the bandgap reference voltage are
fed to an operational amplifier. The amplified input voltage difference controls the gate of an output driver
which basically is a large NMOS transistor connected to the output.
14.4.3 Reduced-Power Mode
In reduced-power mode, the driver gate is connected to a buffered fraction of the input voltage (VDDR).
The operational amplifier and the bandgap are disabled to reduce power consumption.
14.4.4 LVD — Low-Voltage Detect
sub-block LVD is responsible for generating the low-voltage interrupt (LVI). LVD monitors the input
voltage (VDDA–VSSA) and continuously updates the status flag LVDS. Interrupt flag LVIF is set whenever
status flag LVDS changes its value. The LVD is available in FPM and is inactive in reduced-power mode
and shutdown mode.
14.4.5 POR — Power-On Reset
This functional block monitors output VDD. If VDD is below VPORD, signal POR is high, if it exceeds
VPORD, the signal goes low. The transition to low forces the CPU in the power-on sequence.
Due to its role during chip power-up this module must be active in all operating modes of VREG3V3V2.
14.4.6 LVR — Low-Voltage Reset
Block LVR monitors the primary output voltage VDD. If it drops below the assertion level (VLVRA) signal
LVR asserts and when rising above the deassertion level (VLVRD) signal LVR negates again. The LVR
function is available only in full-performance mode.
14.4.7 CTRL — Regulator Control
This part contains the register block of VREG3V3V2 and further digital functionality needed to control
the operating modes. CTRL also represents the interface to the digital core logic.
Chapter 14 Dual Output Voltage Regulator (VREG3V3V2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 447
14.5 Resets
This subsection describes how VREG3V3V2 controls the reset of the MCU.The reset values of registers
and signals are provided in Section 14.3, “Memory Map and Register Definition”. Possible reset sources
are listed in Table 14-4.
14.5.1 Power-On Reset
During chip power-up the digital core may not work if its supply voltage VDD is below the POR
deassertion level (VPORD). Therefore, signal POR which forces the other blocks of the device into reset is
kept high until VDD exceeds VPORD. Then POR becomes low and the reset generator of the device
continues the start-up sequence. The power-on reset is active in all operation modes of VREG3V3V2.
14.5.2 Low-Voltage Reset
For details on low-voltage reset see Section 14.4.6, “LVR — Low-Voltage Reset”.
14.6 Interrupts
This subsection describes all interrupts originated by VREG3V3V2.
The interrupt vectors requested by VREG3V3V2 are listed in Table 14-5. Vector addresses and interrupt
priorities are defined at MCU level.
14.6.1 LVI — Low-Voltage Interrupt
In FPM VREG3V3V2 monitors the input voltage VDDA. Whenever VDDA drops below level VLVIA the
status bit LVDS is set to 1. Vice versa, LVDS is reset to 0 when VDDA rises above level VLVID. An
interrupt, indicated by flag LVIF = 1, is triggered by any change of the status bit LVDS if interrupt enable
bit LVIE = 1.
NOTE
On entering the reduced-power mode, the LVIF is not cleared by the
VREG3V3V2.
Table 14-4. VREG3V3V2 — Reset Sources
Reset Source Local Enable
Power-on reset Always active
Low-voltage reset Available only in full-performance mode
Table 14-5. VREG3V3V2 — Interrupt Vectors
Interrupt Source Local Enable
Low Voltage Interrupt (LVI) LVIE = 1; Available only in full-performance mode
Chapter 14 Dual Output Voltage Regulator (VREG3V3V2) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
448 Freescale Semiconductor
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 449
Chapter 15
Background Debug Module (BDMV4) Block Description
15.1 Introduction
This section describes the functionality of the background debug module (BDM) sub-block of the HCS12
core platform.
A block diagram of the BDM is shown in Figure 15-1.
Figure 15-1. BDM Block Diagram
The background debug module (BDM) sub-block is a single-wire, background debug system implemented
in on-chip hardware for minimal CPU intervention. All interfacing with the BDM is done via the BKGD
pin.
BDMV4 has enhanced capability for maintaining synchronization between the target and host while
allowing more flexibility in clock rates. This includes a sync signal to show the clock rate and a handshake
signal to indicate when an operation is complete. The system is backwards compatible with older external
interfaces.
15.1.1 Features
Single-wire communication with host development system
BDMV4 (and BDM2): Enhanced capability for allowing more flexibility in clock rates
BDMV4: SYNC command to determine communication rate
BDMV4: GO_UNTIL command
BDMV4: Hardware handshake protocol to increase the performance of the serial communication
Active out of reset in special single-chip mode
ENBDM
SDV
16-BIT SHIFT REGISTER
BKGD
CLOCKS
DATA
ADDRESS
HOST
SYSTEM
BUS INTERFACE
AND
CONTROL LOGIC
INSTRUCTION DECODE
AND EXECUTION
STANDARD BDM
FIRMWARE
LOOKUP TABLE
CLKSW
BDMACT
ENTAG
TRACE
Chapter 15 Background Debug Module (BDMV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
450 Freescale Semiconductor
Nine hardware commands using free cycles, if available, for minimal CPU intervention
Hardware commands not requiring active BDM
15 firmware commands execute from the standard BDM firmware lookup table
Instruction tagging capability
Software control of BDM operation during wait mode
Software selectable clocks
When secured, hardware commands are allowed to access the register space in special single-chip
mode, if the FLASH and EEPROM erase tests fail.
15.1.2 Modes of Operation
BDM is available in all operating modes but must be enabled before firmware commands are executed.
Some system peripherals may have a control bit which allows suspending the peripheral function during
background debug mode.
15.1.2.1 Regular Run Modes
All of these operations refer to the part in run mode. The BDM does not provide controls to conserve power
during run mode.
Normal operation
General operation of the BDM is available and operates the same in all normal modes.
Special single-chip mode
In special single-chip mode, background operation is enabled and active out of reset. This allows
programming a system with blank memory.
Special peripheral mode
BDM is enabled and active immediately out of reset. BDM can be disabled
by clearing the BDMACT bit in the BDM status (BDMSTS) register. The
BDM serial system should not be used in special peripheral mode.
Emulation modes
General operation of the BDM is available and operates the same as in normal modes.
15.1.2.2 Secure Mode Operation
If the part is in secure mode, the operation of the BDM is reduced to a small subset of its regular run mode
operation. Secure operation prevents access to FLASH or EEPROM other than allowing erasure.
15.2 External Signal Description
A single-wire interface pin is used to communicate with the BDM system. Two additional pins are used
for instruction tagging. These pins are part of the multiplexed external bus interface (MEBI) sub-block and
all interfacing between the MEBI and BDM is done within the core interface boundary. Functional
descriptions of the pins are provided below for completeness.
Chapter 15 Background Debug Module (BDMV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 451
BKGD — Background interface pin
TAGHI — High byte instruction tagging pin
TAGLO — Low byte instruction tagging pin
BKGD and TAGHI share the same pin.
TAGLO and LSTRB share the same pin.
NOTE
Generally these pins are shared as described, but it is best to check the
device overview chapter to make certain. All MCUs at the time of this
writing have followed this pin sharing scheme.
15.2.1 BKGD — Background Interface Pin
Debugging control logic communicates with external devices serially via the single-wire background
interface pin (BKGD). During reset, this pin is a mode select input which selects between normal and
special modes of operation. After reset, this pin becomes the dedicated serial interface pin for the
background debug mode.
15.2.2 TAGHI — High Byte Instruction Tagging Pin
This pin is used to tag the high byte of an instruction. When instruction tagging is on, a logic 0 at the falling
edge of the external clock (ECLK) tags the high half of the instruction word being read into the instruction
queue.
15.2.3 TAGLO — Low Byte Instruction Tagging Pin
This pin is used to tag the low byte of an instruction. When instruction tagging is on and low strobe is
enabled, a logic 0 at the falling edge of the external clock (ECLK) tags the low half of the instruction word
being read into the instruction queue.
Chapter 15 Background Debug Module (BDMV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
452 Freescale Semiconductor
15.3 Memory Map and Register Definition
A summary of the registers associated with the BDM is shown in Figure 15-2. Registers are accessed by
host-driven communications to the BDM hardware using READ_BD and WRITE_BD commands.
Detailed descriptions of the registers and associated bits are given in the subsections that follow.
15.3.1 Module Memory Map
Table 15-1. INT Memory Map
Register
Address Use Access
0xFF00 Reserved
0xFF01 BDM Status Register (BDMSTS) R/W
0xFF02–
0xFF05 Reserved
0xFF06 BDM CCR Holding Register (BDMCCR) R/W
0xFF07 BDM Internal Register Position (BDMINR) R
0xFF08–
0xFF0B Reserved
Chapter 15 Background Debug Module (BDMV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 453
15.3.2 Register Descriptions
Register
Name Bit 7 6 5 4321Bit 0
0xFF00
Reserved RXXXXXX00
W
0xFF01
BDMSTS RENBDM BDMACT ENTAG SDV TRACE CLKSW UNSEC 0
W
0xFF02
Reserved RXXXXXXXX
W
0xFF03
Reserved RXXXXXXXX
W
0xFF04
Reserved RXXXXXXXX
W
0xFF05
Reserved RXXXXXXXX
W
0xFF06
BDMCCR RCCR7 CCR6 CCR5 CCR4 CCR3 CCR2 CCR1 CCR0
W
0xFF07
BDMINR R 0 REG14 REG13 REG12 REG11 0 0 0
W
0xFF08
Reserved R00000000
W
0xFF09
Reserved R00000000
W
0xFF0A
Reserved RXXXXXXXX
W
0xFF0B
Reserved RXXXXXXXX
W
= Unimplemented, Reserved = Implemented (do not alter)
X = Indeterminate 0 = Always read zero
Figure 15-2. BDM Register Summary
Chapter 15 Background Debug Module (BDMV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
454 Freescale Semiconductor
15.3.2.1 BDM Status Register (BDMSTS)
Read: All modes through BDM operation
Write: All modes but subject to the following:
BDMACT can only be set by BDM hardware upon entry into BDM. It can only be cleared by the
standard BDM firmware lookup table upon exit from BDM active mode.
CLKSW can only be written via BDM hardware or standard BDM firmware write commands.
All other bits, while writable via BDM hardware or standard BDM firmware write commands,
should only be altered by the BDM hardware or standard firmware lookup table as part of BDM
command execution.
ENBDM should only be set via a BDM hardware command if the BDM firmware commands are
needed. (This does not apply in special single-chip mode).
0xFF01
76543210
RENBDM BDMACT ENTAG SDV TRACE CLKSW UNSEC 0
W
Reset:
Special single-chip mode:
Special peripheral mode:
All other modes:
11
0
0
0
1ENBDM is read as "1" by a debugging environment in Special single-chip mode when the device is not secured or secured
but fully erased (Flash and EEPROM).This is because the ENBDM bit is set by the standard firmware before a BDM command
can be fully transmitted and executed.
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
02
0
0
0
2UNSEC is read as "1" by a debugging environment in Special single-chip mode when the device is secured and fully erased,
else it is "0" and can only be read if not secure (see also bit description).
0
0
0
0
= Unimplemented or Reserved = Implemented (do not alter)
Figure 15-3. BDM Status Register (BDMSTS)
Note:
Chapter 15 Background Debug Module (BDMV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 455
Table 15-2. BDMSTS Field Descriptions
Field Description
7
ENBDM Enable BDM — This bit controls whether the BDM is enabled or disabled. When enabled, BDM can be made
active to allow firmware commands to be executed. When disabled, BDM cannot be made active but BDM
hardware commands are allowed.
0 BDM disabled
1 BDM enabled
Note: ENBDM is set by the firmware immediately out of reset in special single-chip mode. In secure mode, this
bit will not be set by the firmware until after the EEPROM and FLASH erase verify tests are complete.
6
BDMACT BDM Active Status — This bit becomes set upon entering BDM. The standard BDM firmware lookup table is
then enabled and put into the memory map. BDMACT is cleared by a carefully timed store instruction in the
standard BDM firmware as part of the exit sequence to return to user code and remove the BDM memory from
the map.
0 BDM not active
1 BDM active
5
ENTAG Tagging Enable — This bit indicates whether instruction tagging in enabled or disabled. It is set when the
TAGGO command is executed and cleared when BDM is entered. The serial system is disabled and the tag
function enabled 16 cycles after this bit is written. BDM cannot process serial commands while tagging is active.
0 Tagging not enabled or BDM active
1 Tagging enabled
4
SDV Shift Data Valid This bit is set and cleared by the BDM hardware. It is set after data has been transmitted as
part of a firmware read command or after data has been received as part of a firmware write command. It is
cleared when the next BDM command has been received or BDM is exited. SDV is used by the standard BDM
firmware to control program flow execution.
0 Data phase of command not complete
1 Data phase of command is complete
3
TRACE TRACE1 BDM Firmware Command is Being Executed — This bit gets set when a BDM TRACE1 firmware
command is first recognized. It will stay set as long as continuous back-to-back TRACE1 commands are
executed. This bit will get cleared when the next command that is not a TRACE1 command is recognized.
0 TRACE1 command is not being executed
1 TRACE1 command is being executed
Chapter 15 Background Debug Module (BDMV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
456 Freescale Semiconductor
2
CLKSW Clock Switch The CLKSW bit controls which clock the BDM operates with. It is only writable from a hardware
BDM command. A 150 cycle delay at the clock speed that is active during the data portion of the command will
occur before the new clock source is guaranteed to be active. The start of the next BDM command uses the new
clock for timing subsequent BDM communications.
Table 15-3 shows the resulting BDM clock source based on the CLKSW and the PLLSEL (Pll select from the
clock and reset generator) bits.
Note: The BDM alternate clock source can only be selected when CLKSW = 0 and PLLSEL = 1. The BDM serial
interface is now fully synchronized to the alternate clock source, when enabled. This eliminates frequency
restriction on the alternate clock which was required on previous versions. Refer to the device overview
section to determine which clock connects to the alternate clock source input.
Note: If the acknowledge function is turned on, changing the CLKSW bit will cause the ACK to be at the new rate
for the write command which changes it.
1
UNSEC Unsecure This bit is only writable in special single-chip mode from the BDM secure firmware and always gets
reset to zero. It is in a zero state as secure mode is entered so that the secure BDM firmware lookup table is
enabled and put into the memory map along with the standard BDM firmware lookup table.
Thesecure BDMfirmwarelookup tableverifiesthat theon-chip EEPROMandFLASH EEPROMareerased.This
being the case, the UNSEC bit is set and the BDM program jumps to the start of the standard BDM firmware
lookup table and the secure BDM firmware lookup table is turned off. If the erase test fails, the UNSEC bit will
not be asserted.
0 System is in a secured mode
1 System is in a unsecured mode
Note: When UNSEC is set, security is off and the user can change the state of the secure bits in the on-chip
FLASH EEPROM. Note that if the user does not change the state of the bits to “unsecured” mode, the
system will be secured again when it is next taken out of reset.
Table 15-3. BDM Clock Sources
PLLSEL CLKSW BDMCLK
0 0 Bus clock
0 1 Bus clock
1 0 Alternate clock (refer to the device overview chapter to determine the alternate clock
source)
1 1 Bus clock dependent on the PLL
Table 15-2. BDMSTS Field Descriptions (continued)
Field Description
Chapter 15 Background Debug Module (BDMV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 457
15.3.2.2 BDM CCR Holding Register (BDMCCR)
Read: All modes
Write: All modes
NOTE
When BDM is made active, the CPU stores the value of the CCR register in
the BDMCCR register. However, out of special single-chip reset, the
BDMCCR is set to 0xD8 and not 0xD0 which is the reset value of the CCR
register.
When entering background debug mode, the BDM CCR holding register is used to save the contents of the
condition code register of the user’s program. It is also used for temporary storage in the standard BDM
firmware mode. The BDM CCR holding register can be written to modify the CCR value.
15.3.2.3 BDM Internal Register Position Register (BDMINR)
Read: All modes
Write: Never
0xFF06
76543210
RCCR7 CCR6 CCR5 CCR4 CCR3 CCR2 CCR1 CCR0
W
Reset 0 0 0 00000
Figure 15-4. BDM CCR Holding Register (BDMCCR)
0xFF07
76543210
R 0 REG14 REG13 REG12 REG11 0 0 0
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 15-5. BDM Internal Register Position (BDMINR)
Table 15-4. BDMINR Field Descriptions
Field Description
6:3
REG[14:11] Internal Register Map Position These four bits show the state of the upper five bits of the base address for
the system’s relocatable register block. BDMINR is a shadow of the INITRG register which maps the register
block to any 2K byte space within the first 32K bytes of the 64K byte address space.
Chapter 15 Background Debug Module (BDMV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
458 Freescale Semiconductor
15.4 Functional Description
The BDM receives and executes commands from a host via a single wire serial interface. There are two
types of BDM commands, namely, hardware commands and firmware commands.
Hardware commands are used to read and write target system memory locations and to enter active
background debug mode, see Section 15.4.3, “BDM Hardware Commands.” Target system memory
includes all memory that is accessible by the CPU.
Firmware commands are used to read and write CPU resources and to exit from active background debug
mode, see Section 15.4.4, “Standard BDM Firmware Commands. The CPU resources referred to are the
accumulator (D), X index register (X), Y index register (Y), stack pointer (SP), and program counter (PC).
Hardware commands can be executed at any time and in any mode excluding a few exceptions as
highlighted, see Section 15.4.3, “BDM Hardware Commands. Firmware commands can only be executed
when the system is in active background debug mode (BDM).
15.4.1 Security
If the user resets into special single-chip mode with the system secured, a secured mode BDM firmware
lookup table is brought into the map overlapping a portion of the standard BDM firmware lookup table.
The secure BDM firmware verifies that the on-chip EEPROM and FLASH EEPROM are erased. This
being the case, the UNSEC bit will get set. The BDM program jumps to the start of the standard BDM
firmware and the secured mode BDM firmware is turned off and all BDM commands are allowed. If the
EEPROM or FLASH do not verify as erased, the BDM firmware sets the ENBDM bit, without asserting
UNSEC, and the firmware enters a loop. This causes the BDM hardware commands to become enabled,
but does not enable the firmware commands. This allows the BDM hardware to be used to erase the
EEPROM and FLASH. After execution of the secure firmware, regardless of the results of the erase tests,
the CPU registers, INITEE and PPAGE, will no longer be in their reset state.
15.4.2 Enabling and Activating BDM
The system must be in active BDM to execute standard BDM firmware commands. BDM can be activated
only after being enabled. BDM is enabled by setting the ENBDM bit in the BDM status (BDMSTS)
register. The ENBDM bit is set by writing to the BDM status (BDMSTS) register, via the single-wire
interface, using a hardware command such as WRITE_BD_BYTE.
After being enabled, BDM is activated by one of the following1:
Hardware BACKGROUND command
BDM external instruction tagging mechanism
CPU BGND instruction
Breakpoint sub-block’s force or tag mechanism2
When BDM is activated, the CPU finishes executing the current instruction and then begins executing the
firmware in the standard BDM firmware lookup table. When BDM is activated by the breakpoint
1. BDM is enabled and active immediately out of special single-chip reset.
2. This method is only available on systems that have a a breakpoint or a debug sub-block.
Chapter 15 Background Debug Module (BDMV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 459
sub-block, the type of breakpoint used determines if BDM becomes active before or after execution of the
next instruction.
NOTE
If an attempt is made to activate BDM before being enabled, the CPU
resumes normal instruction execution after a brief delay. If BDM is not
enabled, any hardware BACKGROUND commands issued are ignored by
the BDM and the CPU is not delayed.
In active BDM, the BDM registers and standard BDM firmware lookup table are mapped to addresses
0xFF00 to 0xFFFF. BDM registers are mapped to addresses 0xFF00 to 0xFF07. The BDM uses these
registers which are readable anytime by the BDM. However, these registers are not readable by user
programs.
15.4.3 BDM Hardware Commands
Hardware commands are used to read and write target system memory locations and to enter active
background debug mode. Target system memory includes all memory that is accessible by the CPU such
as on-chip RAM, EEPROM, FLASH EEPROM, I/O and control registers, and all external memory.
Hardware commands are executed with minimal or no CPU intervention and do not require the system to
be in active BDM for execution, although they can continue to be executed in this mode. When executing
a hardware command, the BDM sub-block waits for a free CPU bus cycle so that the background access
does not disturb the running application program. If a free cycle is not found within 128 clock cycles, the
CPU is momentarily frozen so that the BDM can steal a cycle. When the BDM finds a free cycle, the
operation does not intrude on normal CPU operation provided that it can be completed in a single cycle.
However, if an operation requires multiple cycles the CPU is frozen until the operation is complete, even
though the BDM found a free cycle.
Chapter 15 Background Debug Module (BDMV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
460 Freescale Semiconductor
The BDM hardware commands are listed in Table 15-5.
NOTE:
If enabled, ACK will occur when data is ready for transmission for all BDM READ commands and will occur after the write is
complete for all BDM WRITE commands.
The READ_BD and WRITE_BD commands allow access to the BDM register locations. These locations
are not normally in the system memory map but share addresses with the application in memory. To
distinguish between physical memory locations that share the same address, BDM memory resources are
enabled just for the READ_BD and WRITE_BD access cycle. This allows the BDM to access BDM
locations unobtrusively, even if the addresses conflict with the application memory map.
15.4.4 Standard BDM Firmware Commands
Firmware commands are used to access and manipulate CPU resources. The system must be in active
BDM to execute standard BDM firmware commands, see Section 15.4.2, “Enabling and Activating
BDM.” Normal instruction execution is suspended while the CPU executes the firmware located in the
standard BDM firmware lookup table. The hardware command BACKGROUND is the usual way to
activate BDM.
As the system enters active BDM, the standard BDM firmware lookup table and BDM registers become
visible in the on-chip memory map at 0xFF00–0xFFFF, and the CPU begins executing the standard BDM
Table 15-5. Hardware Commands
Command Opcode
(hex) Data Description
BACKGROUND 90 None Enter background mode if firmware is enabled. If enabled, an ACK will
be issued when the part enters active background mode.
ACK_ENABLE D5 None Enable handshake. Issues an ACK pulse after the command is
executed.
ACK_DISABLE D6 None Disable handshake. This command does not issue an ACK pulse.
READ_BD_BYTE E4 16-bit address
16-bit data out Read from memory with standard BDM firmware lookup table in map.
Odd address data on low byte; even address data on high byte.
READ_BD_WORD EC 16-bit address
16-bit data out Read from memory with standard BDM firmware lookup table in map.
Must be aligned access.
READ_BYTE E0 16-bit address
16-bit data out Read from memory with standard BDM firmware lookup table out of
map. Odd address data on low byte; even address data on high byte.
READ_WORD E8 16-bit address
16-bit data out Read from memory with standard BDM firmware lookup table out of
map. Must be aligned access.
WRITE_BD_BYTE C4 16-bit address
16-bit data in Write to memory with standard BDM firmware lookup table in map. Odd
address data on low byte; even address data on high byte.
WRITE_BD_WORD CC 16-bit address
16-bit data in Write to memory withstandard BDM firmwarelookup tablein map. Must
be aligned access.
WRITE_BYTE C0 16-bit address
16-bit data in Write to memory with standard BDM firmware lookup table out of map.
Odd address data on low byte; even address data on high byte.
WRITE_WORD C8 16-bit address
16-bit data in Write to memory with standard BDM firmware lookup table out of map.
Must be aligned access.
Chapter 15 Background Debug Module (BDMV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 461
firmware. The standard BDM firmware watches for serial commands and executes them as they are
received.
The firmware commands are shown in Table 15-6.
15.4.5 BDM Command Structure
Hardware and firmware BDM commands start with an 8-bit opcode followed by a 16-bit address and/or a
16-bit data word depending on the command. All the read commands return 16 bits of data despite the byte
or word implication in the command name.
NOTE
8-bit reads return 16-bits of data, of which, only one byte will contain valid
data. If reading an even address, the valid data will appear in the MSB. If
reading an odd address, the valid data will appear in the LSB.
Table 15-6. Firmware Commands
Command1
1If enabled, ACK will occur when data is ready for transmission for all BDM READ commands and will occur after the write is
complete for all BDM WRITE commands.
Opcode (hex) Data Description
READ_NEXT 62 16-bit data out Increment X by 2 (X = X + 2), then read word X points to.
READ_PC 63 16-bit data out Read program counter.
READ_D 64 16-bit data out Read D accumulator.
READ_X 65 16-bit data out Read X index register.
READ_Y 66 16-bit data out Read Y index register.
READ_SP 67 16-bit data out Read stack pointer.
WRITE_NEXT 42 16-bit data in Increment X by 2 (X = X + 2), then write word to location pointed to by X.
WRITE_PC 43 16-bit data in Write program counter.
WRITE_D 44 16-bit data in Write D accumulator.
WRITE_X 45 16-bit data in Write X index register.
WRITE_Y 46 16-bit data in Write Y index register.
WRITE_SP 47 16-bit data in Write stack pointer.
GO 08 None Go to user program. If enabled, ACK will occur when leaving active
background mode.
GO_UNTIL2
2Both WAIT (with clocks to the S12 CPU core disabled) and STOP disable the ACK function. The GO_UNTIL command will not
get an Acknowledge if one of these two CPU instructions occurs before the “UNTIL instruction. This can be a problem for any
instruction that uses ACK, but GO_UNTIL is a lot more difficult for the development tool to time-out.
0C None Go to user program. If enabled, ACK will occur upon returning to active
background mode.
TRACE1 10 None Execute one user instruction then return to active BDM. If enabled, ACK
will occur upon returning to active background mode.
TAGGO 18 None Enable tagging and go to user program. There is no ACK pulse related to
this command.
Chapter 15 Background Debug Module (BDMV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
462 Freescale Semiconductor
NOTE
16-bit misaligned reads and writes are not allowed. If attempted, the BDM
will ignore the least significant bit of the address and will assume an even
address from the remaining bits.
For hardware data read commands, the external host must wait 150 bus clock cycles after sending the
address before attempting to obtain the read data. This is to be certain that valid data is available in the
BDM shift register, ready to be shifted out. For hardware write commands, the external host must wait
150 bus clock cycles after sending the data to be written before attempting to send a new command. This
is to avoid disturbing the BDM shift register before the write has been completed. The 150 bus clock cycle
delay in both cases includes the maximum 128 cycle delay that can be incurred as the BDM waits for a
free cycle before stealing a cycle.
For firmware read commands, the external host should wait 44 bus clock cycles after sending the command
opcode and before attempting to obtain the read data. This includes the potential of an extra 7 cycles when
the access is external with a narrow bus access (+1 cycle) and / or a stretch (+1, 2, or 3 cycles), (7 cycles
could be needed if both occur). The 44 cycle wait allows enough time for the requested data to be made
available in the BDM shift register, ready to be shifted out.
NOTE
This timing has increased from previous BDM modules due to the new
capability in which the BDM serial interface can potentially run faster than
the bus. On previous BDM modules this extra time could be hidden within
the serial time.
For firmware write commands, the external host must wait 32 bus clock cycles after sending the data to be
written before attempting to send a new command. This is to avoid disturbing the BDM shift register
before the write has been completed.
The external host should wait 64 bus clock cycles after a TRACE1 or GO command before starting any
new serial command. This is to allow the CPU to exit gracefully from the standard BDM firmware lookup
table and resume execution of the user code. Disturbing the BDM shift register prematurely may adversely
affect the exit from the standard BDM firmware lookup table.
NOTE
If the bus rate of the target processor is unknown or could be changing, it is
recommended that the ACK (acknowledge function) be used to indicate
when an operation is complete. When using ACK, the delay times are
automated.
Figure 15-6 represents the BDM command structure. The command blocks illustrate a series of eight bit
times starting with a falling edge. The bar across the top of the blocks indicates that the BKGD line idles
in the high state. The time for an 8-bit command is 8 × 16 target clock cycles.1
1. Target clock cycles are cycles measured using the target MCU’s serial clock rate. See Section 15.4.6, “BDM Serial Interface,”
and Section 15.3.2.1, “BDM Status Register (BDMSTS),” for information on how serial clock rate is selected.
Chapter 15 Background Debug Module (BDMV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 463
Figure 15-6. BDM Command Structure
15.4.6 BDM Serial Interface
The BDM communicates with external devices serially via the BKGD pin. During reset, this pin is a mode
select input which selects between normal and special modes of operation. After reset, this pin becomes
the dedicated serial interface pin for the BDM.
The BDM serial interface is timed using the clock selected by the CLKSW bit in the status register see
Section 15.3.2.1, “BDM Status Register (BDMSTS). This clock will be referred to as the target clock in
the following explanation.
The BDM serial interface uses a clocking scheme in which the external host generates a falling edge on
the BKGD pin to indicate the start of each bit time. This falling edge is sent for every bit whether data is
transmitted or received. Data is transferred most significant bit (MSB) first at 16 target clock cycles per
bit. The interface times out if 512 clock cycles occur between falling edges from the host.
The BKGD pin is a pseudo open-drain pin and has an weak on-chip active pull-up that is enabled at all
times. It is assumed that there is an external pull-up and that drivers connected to BKGD do not typically
drive the high level. Because R-C rise time could be unacceptably long, the target system and host provide
brief driven-high (speedup) pulses to drive BKGD to a logic 1. The source of this speedup pulse is the host
for transmit cases and the target for receive cases.
The timing for host-to-target is shown in Figure 15-7 and that of target-to-host in Figure 15-8 and
Figure 15-9. All four cases begin when the host drives the BKGD pin low to generate a falling edge.
Because the host and target are operating from separate clocks, it can take the target system up to one full
clock cycle to recognize this edge. The target measures delays from this perceived start of the bit time
while the host measures delays from the point it actually drove BKGD low to start the bit up to one target
HARDWARE
HARDWARE
FIRMWARE
FIRMWARE
GO,
44-BC
BC = BUS CLOCK CYCLES
COMMAND ADDRESS
150-BC
DELAY
NEXT
DELAY
8 BITS
AT 16 TC/BIT
16 BITS
AT 16 TC/BIT
16 BITS
AT16 TC/BIT
COMMAND ADDRESS DATA NEXT
DATA
READ
WRITE
READ
WRITE
TRACE
COMMAND NEXT
COMMAND DATA
64-BC
DELAY
NEXT
COMMAND
150-BC
DELAY
32-BC
DELAY
COMMAND
COMMAND
COMMAND
COMMAND
DATA
NEXT
COMMAND
TC = TARGET CLOCK CYCLES
Chapter 15 Background Debug Module (BDMV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
464 Freescale Semiconductor
clock cycle earlier. Synchronization between the host and target is established in this manner at the start
of every bit time.
Figure 15-7 shows an external host transmitting a logic 1 and transmitting a logic 0 to the BKGD pin of a
target system. The host is asynchronous to the target, so there is up to a one clock-cycle delay from the
host-generated falling edge to where the target recognizes this edge as the beginning of the bit time. Ten
target clock cycles later, the target senses the bit level on the BKGD pin. Internal glitch detect logic
requires the pin be driven high no later that eight target clock cycles after the falling edge for a logic 1
transmission.
Because the host drives the high speedup pulses in these two cases, the rising edges look like digitally
driven signals.
Figure 15-7. BDM Host-to-Target Serial Bit Timing
The receive cases are more complicated. Figure 15-8 shows the host receiving a logic 1 from the target
system. Because the host is asynchronous to the target, there is up to one clock-cycle delay from the
host-generated falling edge on BKGD to the perceived start of the bit time in the target. The host holds the
BKGD pin low long enough for the target to recognize it (at least two target clock cycles). The host must
release the low drive before the target drives a brief high speedup pulse seven target clock cycles after the
perceived start of the bit time. The host should sample the bit level about 10 target clock cycles after it
started the bit time.
EARLIEST
START OF
NEXT BIT
TARGET SENSES BIT
10 CYCLES
SYNCHRONIZATION
UNCERTAINTY
CLOCK
TARGET SYSTEM
HOST
TRANSMIT 1
HOST
TRANSMIT 0
PERCEIVED
S
TART OF BIT TIME
Chapter 15 Background Debug Module (BDMV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 465
Figure 15-8. BDM Target-to-Host Serial Bit Timing (Logic 1)
Figure 15-9 shows the host receiving a logic 0 from the target. Because the host is asynchronous to the
target, there is up to a one clock-cycle delay from the host-generated falling edge on BKGD to the start of
the bit time as perceived by the target. The host initiates the bit time but the target finishes it. Because the
target wants the host to receive a logic 0, it drives the BKGD pin low for 13 target clock cycles then briefly
drives it high to speed up the rising edge. The host samples the bit level about 10 target clock cycles after
starting the bit time.
Figure 15-9. BDM Target-to-Host Serial Bit Timing (Logic 0)
HIGH-IMPEDANCE
EARLIEST
START OF
NEXT BIT
R-C RISE
10 CYCLES
10 CYCLES
HOST SAMPLES
BKGD PIN
PERCEIVED
START OF BIT TIME
BKGD PIN
CLOCK
TARGET SYSTEM
HOST
DRIVE TO
BKGD PIN
TARGET SYSTEM
SPEEDUP
PULSE
HIGH-IMPEDANCE
HIGH-IMPEDANCE
EARLIEST
START OF
NEXT BIT
CLOCK
TARGET SYS.
HOST
DRIVE TO
BKGD PIN
BKGD PIN
PERCEIVED
START OF BIT TIME
10 CYCLES
10 CYCLES
HOST SAMPLES
BKGD PIN
TARGET SYS.
DRIVE AND
SPEEDUP PULSE
SPEEDUP PULSE
HIGH-IMPEDANCE
Chapter 15 Background Debug Module (BDMV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
466 Freescale Semiconductor
15.4.7 Serial Interface Hardware Handshake Protocol
BDM commands that require CPU execution are ultimately treated at the MCU bus rate. Because the BDM
clock source can be asynchronously related to the bus frequency, when CLKSW = 0, it is very helpful to
provide a handshake protocol in which the host could determine when an issued command is executed by
the CPU. The alternative is to always wait the amount of time equal to the appropriate number of cycles at
the slowest possible rate the clock could be running. This sub-section will describe the hardware
handshake protocol.
The hardware handshake protocol signals to the host controller when an issued command was successfully
executed by the target. This protocol is implemented by a 16 serial clock cycle low pulse followed by a
brief speedup pulse in the BKGD pin. This pulse is generated by the target MCU when a command, issued
by the host, has been successfully executed (see Figure 15-10). This pulse is referred to as the ACK pulse.
After the ACK pulse has finished: the host can start the bit retrieval if the last issued command was a read
command, or start a new command if the last command was a write command or a control command
(BACKGROUND, GO, GO_UNTIL, or TRACE1). The ACK pulse is not issued earlier than 32 serial
clock cycles after the BDM command was issued. The end of the BDM command is assumed to be the
16th tick of the last bit. This minimum delay assures enough time for the host to perceive the ACK pulse.
Note also that, there is no upper limit for the delay between the command and the related ACK pulse,
because the command execution depends upon the CPU bus frequency, which in some cases could be very
slow compared to the serial communication rate. This protocol allows a great flexibility for the POD
designers, because it does not rely on any accurate time measurement or short response time to any event
in the serial communication.
Figure 15-10. Target Acknowledge Pulse (ACK)
NOTE
If the ACK pulse was issued by the target, the host assumes the previous
command was executed. If the CPU enters WAIT or STOP prior to
executing a hardware command, the ACK pulse will not be issued meaning
that the BDM command was not executed. After entering wait or stop mode,
the BDM command is no longer pending.
16 CYCLES
BDM CLOCK
(TARGET MCU)
TARGET
TRANSMITS
PULSE
ACK
HIGH-IMPEDANCE
BKGD PIN
MINIMUM DELAY
FROM THE BDM COMMAND
32 CYCLES
EARLIEST
START OF
NEXT BIT
SPEEDUP PULSE
16th TICK OF THE
LAST COMMAD BIT
HIGH-IMPEDANCE
Chapter 15 Background Debug Module (BDMV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 467
Figure 15-11 shows the ACK handshake protocol in a command level timing diagram. The READ_BYTE
instruction is used as an example. First, the 8-bit instruction opcode is sent by the host, followed by the
address of the memory location to be read. The target BDM decodes the instruction. A bus cycle is grabbed
(free or stolen) by the BDM and it executes the READ_BYTE operation. Having retrieved the data, the
BDM issues an ACK pulse to the host controller, indicating that the addressed byte is ready to be retrieved.
After detecting the ACK pulse, the host initiates the byte retrieval process. Note that data is sent in the form
of a word and the host needs to determine which is the appropriate byte based on whether the address was
odd or even.
Figure 15-11. Handshake Protocol at Command Level
Differently from the normal bit transfer (where the host initiates the transmission), the serial interface ACK
handshake pulse is initiated by the target MCU by issuing a falling edge in the BKGD pin. The hardware
handshake protocol in Figure 15-10 specifies the timing when the BKGD pin is being driven, so the host
should follow this timing constraint in order to avoid the risk of an electrical conflict in the BKGD pin.
NOTE
The only place the BKGD pin can have an electrical conflict is when one
side is driving low and the other side is issuing a speedup pulse (high). Other
“highs” are pulled rather than driven. However, at low rates the time of the
speedup pulse can become lengthy and so the potential conflict time
becomes longer as well.
The ACK handshake protocol does not support nested ACK pulses. If a BDM command is not
acknowledge by an ACK pulse, the host needs to abort the pending command first in order to be able to
issue a new BDM command. When the CPU enters WAIT or STOP while the host issues a command that
requires CPU execution (e.g., WRITE_BYTE), the target discards the incoming command due to the
WAIT or STOP being detected. Therefore, the command is not acknowledged by the target, which means
that the ACK pulse will not be issued in this case. After a certain time the host should decide to abort the
ACK sequence in order to be free to issue a new command. Therefore, the protocol should provide a
mechanism in which a command, and therefore a pending ACK, could be aborted.
NOTE
Differently from a regular BDM command, the ACK pulse does not provide
a time out. This means that in the case of a WAIT or STOP instruction being
executed, the ACK would be prevented from being issued. If not aborted, the
ACK would remain pending indefinitely. See the handshake abort procedure
described in Section 15.4.8, “Hardware Handshake Abort Procedure.”
READ_BYTE
BDM ISSUES THE
BKGD PIN BYTE ADDRESS
BDM EXECUTES THE
READ_BYTE COMMAND
HOST TARGET
HOSTTARGET
BDM DECODES
THE COMMAND
ACK PULSE (OUT OF SCALE)
HOST TARGET
(2) BYTES ARE
RETRIEVED
NEW BDM
COMMAND
Chapter 15 Background Debug Module (BDMV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
468 Freescale Semiconductor
15.4.8 Hardware Handshake Abort Procedure
The abort procedure is based on the SYNC command. In order to abort a command, which had not issued
the corresponding ACK pulse, the host controller should generate a low pulse in the BKGD pin by driving
it low for at least 128 serial clock cycles and then driving it high for one serial clock cycle, providing a
speedup pulse. By detecting this long low pulse in the BKGD pin, the target executes the SYNC protocol,
see Section 15.4.9, “SYNC Request Timed Reference Pulse, and assumes that the pending command
and therefore the related ACK pulse, are being aborted. Therefore, after the SYNC protocol has been
completed the host is free to issue new BDM commands.
Although it is not recommended, the host could abort a pending BDM command by issuing a low pulse in
the BKGD pin shorter than 128 serial clock cycles, which will not be interpreted as the SYNC command.
The ACK is actually aborted when a falling edge is perceived by the target in the BKGD pin. The short
abort pulse should have at least 4 clock cycles keeping the BKGD pin low, in order to allow the falling
edge to be detected by the target. In this case, the target will not execute the SYNC protocol but the pending
command will be aborted along with the ACK pulse. The potential problem with this abort procedure is
when there is a conflict between the ACK pulse and the short abort pulse. In this case, the target may not
perceive the abort pulse. The worst case is when the pending command is a read command (i.e.,
READ_BYTE). If the abort pulse is not perceived by the target the host will attempt to send a new
command after the abort pulse was issued, while the target expects the host to retrieve the accessed
memory byte. In this case, host and target will run out of synchronism. However, if the command to be
aborted is not a read command the short abort pulse could be used. After a command is aborted the target
assumes the next falling edge, after the abort pulse, is the first bit of a new BDM command.
NOTE
The details about the short abort pulse are being provided only as a reference
for the reader to better understand the BDM internal behavior. It is not
recommended that this procedure be used in a real application.
Because the host knows the target serial clock frequency, the SYNC command (used to abort a command)
does not need to consider the lower possible target frequency. In this case, the host could issue a SYNC
very close to the 128 serial clock cycles length. Providing a small overhead on the pulse length in order to
assure the SYNC pulse will not be misinterpreted by the target. See Section 15.4.9, “SYNC — Request
Timed Reference Pulse.”
Figure 15-12 shows a SYNC command being issued after a READ_BYTE, which aborts the
READ_BYTE command. Note that, after the command is aborted a new command could be issued by the
host computer.
NOTE
Figure 15-12 does not represent the signals in a true timing scale
Chapter 15 Background Debug Module (BDMV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 469
Figure 15-12. ACK Abort Procedure at the Command Level
Figure 15-13 shows a conflict between the ACK pulse and the SYNC request pulse. This conflict could
occur if a POD device is connected to the target BKGD pin and the target is already in debug active mode.
Consider that the target CPU is executing a pending BDM command at the exact moment the POD is being
connected to the BKGD pin. In this case, an ACK pulse is issued along with the SYNC command. In this
case, there is an electrical conflict between the ACK speedup pulse and the SYNC pulse. Because this is
not a probable situation, the protocol does not prevent this conflict from happening.
Figure 15-13. ACK Pulse and SYNC Request Conflict
NOTE
This information is being provided so that the MCU integrator will be aware
that such a conflict could eventually occur.
The hardware handshake protocol is enabled by the ACK_ENABLE and disabled by the ACK_DISABLE
BDM commands. This provides backwards compatibility with the existing POD devices which are not
able to execute the hardware handshake protocol. It also allows for new POD devices, that support the
hardware handshake protocol, to freely communicate with the target device. If desired, without the need
for waiting for the ACK pulse.
READ_BYTE READ_STATUSBKGD PIN MEMORY ADDRESS NEW BDM COMMAND
NEW BDM COMMAND
HOST TARGET HOST TARGET HOST TARGET
SYNC RESPONSE
FROM THE TARGET
(OUT OF SCALE)
BDM DECODE
AND STARTS TO EXECUTES
THE READ_BYTE CMD
READ_BYTE CMD IS ABORTED
BY THE SYNC REQUEST
(OUT OF SCALE)
BDM CLOCK
(TARGET MCU)
TARGET MCU
DRIVES TO
BKGD PIN
BKGD PIN
16 CYCLES
SPEEDUP PULSE
HIGH-IMPEDANCE
HOST
DRIVES SYNC
TO BKGD PIN
ACK PULSE
HOST SYNC REQUEST PULSE
AT LEAST 128 CYCLES
ELECTRICAL CONFLICT
HOST AND
TARGET DRIVE
TO BKGD PIN
Chapter 15 Background Debug Module (BDMV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
470 Freescale Semiconductor
The commands are described as follows:
ACK_ENABLE enables the hardware handshake protocol. The target will issue the ACK pulse
when a CPU command is executed by the CPU. The ACK_ENABLE command itself also has the
ACK pulse as a response.
ACK_DISABLE disables the ACK pulse protocol. In this case, the host needs to use the worst
case delay time at the appropriate places in the protocol.
The default state of the BDM after reset is hardware handshake protocol disabled.
All the read commands will ACK (if enabled) when the data bus cycle has completed and the data is then
ready for reading out by the BKGD serial pin. All the write commands will ACK (if enabled) after the data
has been received by the BDM through the BKGD serial pin and when the data bus cycle is complete. See
Section 15.4.3, “BDM Hardware Commands,” and Section 15.4.4, “Standard BDM Firmware
Commands,” for more information on the BDM commands.
The ACK_ENABLE sends an ACK pulse when the command has been completed. This feature could be
used by the host to evaluate if the target supports the hardware handshake protocol. If an ACK pulse is
issued in response to this command, the host knows that the target supports the hardware handshake
protocol. If the target does not support the hardware handshake protocol the ACK pulse is not issued. In
this case, the ACK_ENABLE command is ignored by the target because it is not recognized as a valid
command.
The BACKGROUND command will issue an ACK pulse when the CPU changes from normal to
background mode. The ACK pulse related to this command could be aborted using the SYNC command.
The GO command will issue an ACK pulse when the CPU exits from background mode. The ACK pulse
related to this command could be aborted using the SYNC command.
The GO_UNTIL command is equivalent to a GO command with exception that the ACK pulse, in this
case, is issued when the CPU enters into background mode. This command is an alternative to the GO
command and should be used when the host wants to trace if a breakpoint match occurs and causes the
CPU to enter active background mode. Note that the ACK is issued whenever the CPU enters BDM, which
could be caused by a breakpoint match or by a BGND instruction being executed. The ACK pulse related
to this command could be aborted using the SYNC command.
The TRACE1 command has the related ACK pulse issued when the CPU enters background active mode
after one instruction of the application program is executed. The ACK pulse related to this command could
be aborted using the SYNC command.
The TAGGO command will not issue an ACK pulse because this would interfere with the tagging function
shared on the same pin.
Chapter 15 Background Debug Module (BDMV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 471
15.4.9 SYNC — Request Timed Reference Pulse
The SYNC command is unlike other BDM commands because the host does not necessarily know the
correct communication speed to use for BDM communications until after it has analyzed the response to
the SYNC command. To issue a SYNC command, the host should perform the following steps:
1. Drive the BKGD pin low for at least 128 cycles at the lowest possible BDM serial communication
frequency (the lowest serial communication frequency is determined by the crystal oscillator or the
clock chosen by CLKSW.)
2. Drive BKGD high for a brief speedup pulse to get a fast rise time (this speedup pulse is typically
one cycle of the host clock.)
3. Remove all drive to the BKGD pin so it reverts to high impedance.
4. Listen to the BKGD pin for the sync response pulse.
Upon detecting the SYNC request from the host, the target performs the following steps:
1. Discards any incomplete command received or bit retrieved.
2. Waits for BKGD to return to a logic 1.
3. Delays 16 cycles to allow the host to stop driving the high speedup pulse.
4. Drives BKGD low for 128 cycles at the current BDM serial communication frequency.
5. Drives a one-cycle high speedup pulse to force a fast rise time on BKGD.
6. Removes all drive to the BKGD pin so it reverts to high impedance.
The host measures the low time of this 128 cycle SYNC response pulse and determines the correct speed
for subsequent BDM communications. Typically, the host can determine the correct communication speed
within a few percent of the actual target speed and the communication protocol can easily tolerate speed
errors of several percent.
As soon as the SYNC request is detected by the target, any partially received command or bit retrieved is
discarded. This is referred to as a soft-reset, equivalent to a time-out in the serial communication. After the
SYNC response, the target will consider the next falling edge (issued by the host) as the start of a new
BDM command or the start of new SYNC request.
Another use of the SYNC command pulse is to abort a pending ACK pulse. The behavior is exactly the
same as in a regular SYNC command. Note that one of the possible causes for a command to not be
acknowledged by the target is a host-target synchronization problem. In this case, the command may not
have been understood by the target and so an ACK response pulse will not be issued.
15.4.10 Instruction Tracing
When a TRACE1 command is issued to the BDM in active BDM, the CPU exits the standard BDM
firmware and executes a single instruction in the user code. As soon as this has occurred, the CPU is forced
to return to the standard BDM firmware and the BDM is active and ready to receive a new command. If
the TRACE1 command is issued again, the next user instruction will be executed. This facilitates stepping
or tracing through the user code one instruction at a time.
Chapter 15 Background Debug Module (BDMV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
472 Freescale Semiconductor
If an interrupt is pending when a TRACE1 command is issued, the interrupt stacking operation occurs but
no user instruction is executed. Upon return to standard BDM firmware execution, the program counter
points to the first instruction in the interrupt service routine.
15.4.11 Instruction Tagging
The instruction queue and cycle-by-cycle CPU activity are reconstructible in real time or from trace history
that is captured by a logic analyzer. However, the reconstructed queue cannot be used to stop the CPU at
a specific instruction. This is because execution already has begun by the time an operation is visible
outside the system. A separate instruction tagging mechanism is provided for this purpose.
The tag follows program information as it advances through the instruction queue. When a tagged
instruction reaches the head of the queue, the CPU enters active BDM rather than executing the instruction.
NOTE
Tagging is disabled when BDM becomes active and BDM serial commands
are not processed while tagging is active.
Executing the BDM TAGGO command configures two system pins for tagging. The TAGLO signal shares
a pin with the LSTRB signal, and the TAGHI signal shares a pin with the BKGD signal.
Table 15-7 shows the functions of the two tagging pins. The pins operate independently, that is the state of
one pin does not affect the function of the other. The presence of logic level 0 on either pin at the fall of
the external clock (ECLK) performs the indicated function. High tagging is allowed in all modes. Low
tagging is allowed only when low strobe is enabled (LSTRB is allowed only in wide expanded modes and
emulation expanded narrow mode).
15.4.12 Serial Communication Time-Out
The host initiates a host-to-target serial transmission by generating a falling edge on the BKGD pin. If
BKGD is kept low for more than 128 target clock cycles, the target understands that a SYNC command
was issued. In this case, the target will keep waiting for a rising edge on BKGD in order to answer the
SYNC request pulse. If the rising edge is not detected, the target will keep waiting forever without any
time-out limit.
Consider now the case where the host returns BKGD to logic one before 128 cycles. This is interpreted as
a valid bit transmission, and not as a SYNC request. The target will keep waiting for another falling edge
marking the start of a new bit. If, however, a new falling edge is not detected by the target within 512 clock
cycles since the last falling edge, a time-out occurs and the current command is discarded without affecting
memory or the operating mode of the MCU. This is referred to as a soft-reset.
Table 15-7. Tag Pin Function
TAGHI TAGLO Tag
1 1 No tag
1 0 Low byte
0 1 High byte
0 0 Both bytes
Chapter 15 Background Debug Module (BDMV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 473
If a read command is issued but the data is not retrieved within 512 serial clock cycles, a soft-reset will
occur causing the command to be disregarded. The data is not available for retrieval after the time-out has
occurred. This is the expected behavior if the handshake protocol is not enabled. However, consider the
behavior where the BDC is running in a frequency much greater than the CPU frequency. In this case, the
command could time out before the data is ready to be retrieved. In order to allow the data to be retrieved
even with a large clock frequency mismatch (between BDC and CPU) when the hardware handshake
protocol is enabled, the time out between a read command and the data retrieval is disabled. Therefore, the
host could wait for more then 512 serial clock cycles and continue to be able to retrieve the data from an
issued read command. However, as soon as the handshake pulse (ACK pulse) is issued, the time-out feature
is re-activated, meaning that the target will time out after 512 clock cycles. Therefore, the host needs to
retrieve the data within a 512 serial clock cycles time frame after the ACK pulse had been issued. After
that period, the read command is discarded and the data is no longer available for retrieval. Any falling
edge of the BKGD pin after the time-out period is considered to be a new command or a SYNC request.
Note that whenever a partially issued command, or partially retrieved data, has occurred the time out in the
serial communication is active. This means that if a time frame higher than 512 serial clock cycles is
observed between two consecutive negative edges and the command being issued or data being retrieved
is not complete, a soft-reset will occur causing the partially received command or data retrieved to be
disregarded. The next falling edge of the BKGD pin, after a soft-reset has occurred, is considered by the
target as the start of a new BDM command, or the start of a SYNC request pulse.
15.4.13 Operation in Wait Mode
The BDM cannot be used in wait mode if the system disables the clocks to the BDM.
There is a clearing mechanism associated with the WAIT instruction when the clocks to the BDM (CPU
core platform) are disabled. As the clocks restart from wait mode, the BDM receives a soft reset (clearing
any command in progress) and the ACK function will be disabled. This is a change from previous BDM
modules.
15.4.14 Operation in Stop Mode
The BDM is completely shutdown in stop mode.
There is a clearing mechanism associated with the STOP instruction. STOP must be enabled and the part
must go into stop mode for this to occur. As the clocks restart from stop mode, the BDM receives a soft
reset (clearing any command in progress) and the ACK function will be disabled. This is a change from
previous BDM modules.
Chapter 15 Background Debug Module (BDMV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
474 Freescale Semiconductor
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 475
Chapter 16
Debug Module (DBGV1) Block Description
16.1 Introduction
This section describes the functionality of the debug (DBG) sub-block of the HCS12 core platform.
The DBG module is designed to be fully compatible with the existing BKP_HCS12_A module (BKP
mode) and furthermore provides an on-chip trace buffer with flexible triggering capability (DBG mode).
The DBG module provides for non-intrusive debug of application software. The DBG module is optimized
for the HCS12 16-bit architecture.
16.1.1 Features
The DBG module in BKP mode includes these distinctive features:
Full or dual breakpoint mode
Compare on address and data (full)
Compare on either of two addresses (dual)
BDM or SWI breakpoint
Enter BDM on breakpoint (BDM)
Execute SWI on breakpoint (SWI)
Tagged or forced breakpoint
Break just before a specific instruction will begin execution (TAG)
Break on the first instruction boundary after a match occurs (Force)
Single, range, or page address compares
Compare on address (single)
Compare on address 256 byte (range)
Compare on any 16K page (page)
At forced breakpoints compare address on read or write
High and/or low byte data compares
Comparator C can provide an additional tag or force breakpoint (enhancement for BKP mode)
Chapter 16 Debug Module (DBGV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
476 Freescale Semiconductor
The DBG in DBG mode includes these distinctive features:
Three comparators (A, B, and C)
Dual mode, comparators A and B used to compare addresses
Full mode, comparator A compares address and comparator B compares data
Can be used as trigger and/or breakpoint
Comparator C used in LOOP1 capture mode or as additional breakpoint
Four capture modes
Normal mode, change-of-flow information is captured based on trigger specification
Loop1 mode, comparator C is dynamically updated to prevent redundant change-of-flow
storage.
Detail mode, address and data for all cycles except program fetch (P) and free (f) cycles are
stored in trace buffer
Profile mode, last instruction address executed by CPU is returned when trace buffer address is
read
Two types of breakpoint or debug triggers
Break just before a specific instruction will begin execution (tag)
Break on the first instruction boundary after a match occurs (force)
BDM or SWI breakpoint
Enter BDM on breakpoint (BDM)
Execute SWI on breakpoint (SWI)
Nine trigger modes for comparators A and B
—A
A or B
A then B
A and B, where B is data (full mode)
A and not B, where B is data (full mode)
Event only B, store data
A then event only B, store data
Inside range, A address B
Outside range, address < Α or address > B
Comparator C provides an additional tag or force breakpoint when capture mode is not configured
in LOOP1 mode.
Sixty-four word (16 bits wide) trace buffer for storing change-of-flow information, event only data
and other bus information.
Source address of taken conditional branches (long, short, bit-conditional, and loop constructs)
Destination address of indexed JMP, JSR, and CALL instruction.
Destination address of RTI, RTS, and RTC instructions
Vector address of interrupts, except for SWI and BDM vectors
Chapter 16 Debug Module (DBGV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 477
Data associated with event B trigger modes
Detail report mode stores address and data for all cycles except program (P) and free (f) cycles
Current instruction address when in profiling mode
BGND is not considered a change-of-flow (cof) by the debugger
16.1.2 Modes of Operation
There are two main modes of operation: breakpoint mode and debug mode. Each one is mutually exclusive
of the other and selected via a software programmable control bit.
In the breakpoint mode there are two sub-modes of operation:
Dual address mode, where a match on either of two addresses will cause the system to enter
background debug mode (BDM) or initiate a software interrupt (SWI).
Full breakpoint mode, where a match on address and data will cause the system to enter
background debug mode (BDM) or initiate a software interrupt (SWI).
In debug mode, there are several sub-modes of operation.
Trigger modes
There are many ways to create a logical trigger. The trigger can be used to capture bus information
either starting from the trigger or ending at the trigger. Types of triggers (A and B are registers):
A only
A or B
A then B
Event only B (data capture)
A then event only B (data capture)
A and B, full mode
A and not B, full mode
Inside range
Outside range
Capture modes
There are several capture modes. These determine which bus information is saved and which is
ignored.
Normal: save change-of-flow program fetches
Loop1: save change-of-flow program fetches, ignoring duplicates
Detail: save all bus operations except program and free cycles
Profile: poll target from external device
16.1.3 Block Diagram
Figure 16-1 is a block diagram of this module in breakpoint mode. Figure 16-2 is a block diagram of this
module in debug mode.
Chapter 16 Debug Module (DBGV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
478 Freescale Semiconductor
Figure 16-1. DBG Block Diagram in BKP Mode
COMPARATOR
COMPARE BLOCK
REGISTER BLOCK
COMPARATOR
COMPARATOR
COMPARATOR
COMPARATOR
COMPARATOR
EXPANSION ADDRESSES
EXPANSION ADDRESSES
ADDRESS HIGH
ADDRESS LOW
DATA HIGH
DATA LOW
ADDRESS HIGH
ADDRESS LOW
COMPARATOR
COMPARATOR
READ DATA HIGH
READ DATA LOW
. . . . . . . . . . . .
CLOCKS AND BKP CONTROL
CONTROL SIGNALS SIGNALS
CONTROL BLOCK
BREAKPOINT MODES
AND GENERATION OF SWI,
FORCE BDM, AND TAGS
EXPANSION ADDRESS
ADDRESS
WRITE DATA
READ DATA
READ/WRITE
CONTROL
CONTROL BITS
CONTROL SIGNALS
RESULTS SIGNALS
BKP0H
BKP0L
BKP0X
BKPCT0
BKP1X
BKPCT1
BKP1L
BKP1H
WRITE
BKP READ
DATA BUS
DATA BUS
DATA/ADDRESS
HIGH MUX
DATA/ADDRESS
LOW MUX
Chapter 16 Debug Module (DBGV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 479
Figure 16-2. DBG Block Diagram in DBG Mode
16.2 External Signal Description
The DBG sub-module relies on the external bus interface (generally the MEBI) when the DBG is matching
on the external bus.
The tag pins in Table 16-1 (part of the MEBI) may also be a part of the breakpoint operation.
Table 16-1. External System Pins Associated with DBG and MEBI
Pin Name Pin Functions Description
BKGD/MODC/
TAGHI TAGHI When instruction tagging is on, a 0 at the falling edge of E tags the high half of the
instruction word being read into the instruction queue.
PE3/LSTRB/ TAGLO TAGLO In expanded wide mode or emulation narrow modes, when instruction tagging is on
and low strobe is enabled, a 0 at the falling edge of E tags the low half of the
instruction word being read into the instruction queue.
TAG
FORCE
ADDRESS BUS
MATCH_A
CONTROL
READ DATA BUS
READ/WRITE
STORE
MCU IN BDM
M
U
X
POINTER
REGISTER
MATCH_B
M
U
X
EVENT ONLY
WRITE DATA BUS
TRACE BUFFER
DBG READ DATA BUS
DBG MODE ENABLE
M
U
X
WRITE DATA BUS
READ DATA BUS
READ/WRITE
MATCH_C
LOOP1
DETAIL
M
U
X
PROFILE CAPTURE MODE
CPU PROGRAM COUNTER
CONTROL
COMPARATOR A
ADDRESS/DATA/CONTROL
COMPARATOR B
COMPARATOR C
REGISTERS
TRACER
BUFFER
CONTROL
LOGIC
CHANGE-OF-FLOW
INDICATORS
OR PROFILING DATA
64 x 16 BIT
WORD
TRACE
BUFFER
PROFILE
CAPTURE
REGISTER
LAST
INSTRUCTION
ADDRESS
BUS CLOCK
INSTRUCTION
LAST CYCLE
Chapter 16 Debug Module (DBGV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
480 Freescale Semiconductor
16.3 Memory Map and Register Definition
A summary of the registers associated with the DBG sub-block is shown in Figure 16-3. Detailed
descriptions of the registers and bits are given in the subsections that follow.
16.3.1 Module Memory Map
16.3.2 Register Descriptions
This section consists of the DBG register descriptions in address order. Most of the register bits can be
written to in either BKP or DBG mode, although they may not have any effect in one of the modes.
However, the only bits in the DBG module that can be written while the debugger is armed (ARM = 1) are
DBGEN and ARM
Table 16-2. DBGV1 Memory Map
Address
Offset Use Access
0x0020 Debug Control Register (DBGC1) R/W
0x0021 Debug Status and Control Register (DBGSC) R/W
0x0022 Debug Trace Buffer Register High (DBGTBH) R
0x0023 Debug Trace Buffer Register Low (DBGTBL) R
0x0024 Debug Count Register (DBGCNT) R
0x0025 Debug Comparator C Extended Register (DBGCCX) R/W
0x0026 Debug Comparator C Register High (DBGCCH) R/W
0x0027 Debug Comparator C Register Low (DBGCCL) R/W
0x0028 Debug Control Register 2 (DBGC2) / (BKPCT0) R/W
0x0029 Debug Control Register 3 (DBGC3) / (BKPCT1) R/W
0x002A Debug Comparator A Extended Register (DBGCAX) / (/BKP0X) R/W
0x002B Debug Comparator A Register High (DBGCAH) / (BKP0H) R/W
0x002C Debug Comparator A Register Low (DBGCAL) / (BKP0L) R/W
0x002D Debug Comparator B Extended Register (DBGCBX) / (BKP1X) R/W
0x002E Debug Comparator B Register High (DBGCBH) / (BKP1H) R/W
0x002F Debug Comparator B Register Low (DBGCBL) / (BKP1L) R/W
Name1Bit 7 6 5 4 3 2 1 Bit 0
0x0020
DBGC1 RDBGEN ARM TRGSEL BEGIN DBGBRK 0CAPMOD
W
0x0021
DBGSC RAF BF CF 0 TRG
W
= Unimplemented or Reserved
Figure 16-3. DBG Register Summary
Chapter 16 Debug Module (DBGV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 481
0x0022
DBGTBH R Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8
W
0x0023
DBGTBL R Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
W
0x0024
DBGCNT R TBF 0 CNT
W
0x0025
DBGCCX(2)RPAGSEL EXTCMP
W
0x0026
DBGCCH(2) RBit 15 14 13 12 11 10 9 Bit 8
W
0x0027
DBGCCL(2) RBit 7 6 5 4 3 2 1 Bit 0
W
0x0028
DBGC2
BKPCT0
RBKABEN FULL BDM TAGAB BKCEN TAGC RWCEN RWC
W
0x0029
DBGC3
BKPCT1
RBKAMBH BKAMBL BKBMBH BKBMBL RWAEN RWA RWBEN RWB
W
0x002A
DBGCAX
BKP0X
RPAGSEL EXTCMP
W
0x002B
DBGCAH
BKP0H
RBit 15 14 13 12 11 10 9 Bit 8
W
0x002C
DBGCAL
BKP0L
RBit 7 6 5 4 3 2 1 Bit 0
W
0x002D
DBGCBX
BKP1X
RPAGSEL EXTCMP
W
0x002E
DBGCBH
BKP1H
RBit 15 14 13 12 11 10 9 Bit 8
W
0x002F
DBGCBL
BKP1L
RBit 7 6 5 4 3 2 1 Bit 0
W
Name1Bit 7 6 5 4 3 2 1 Bit 0
= Unimplemented or Reserved
Figure 16-3. DBG Register Summary (continued)
Chapter 16 Debug Module (DBGV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
482 Freescale Semiconductor
16.3.2.1 Debug Control Register 1 (DBGC1)
NOTE
All bits are used in DBG mode only.
NOTE
This register cannot be written if BKP mode is enabled (BKABEN in
DBGC2 is set).
1TheDBG module is designed forbackwardscompatibility to existingBKP modules.Register and bitnameshavechangedfrom
the BKP module. This column shows the DBG register name, as well as the BKP register name for reference.
2Comparator C can be used to enhance the BKP mode by providing a third breakpoint.
Module Base + 0x0020
Starting address location affected by INITRG register setting.
76543210
RDBGEN ARM TRGSEL BEGIN DBGBRK 0CAPMOD
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 16-4. Debug Control Register (DBGC1)
Table 16-3. DBGC1 Field Descriptions
Field Description
7
DBGEN DBG Mode Enable Bit — The DBGEN bit enables the DBG module for use in DBG mode. This bit cannot be
set if the MCU is in secure mode.
0 DBG mode disabled
1 DBG mode enabled
6
ARM Arm Bit — The ARM bit controls whether the debugger is comparing and storing data in the trace buffer. See
Section 16.4.2.4, “Arming the DBG Module,” for more information.
0 Debugger unarmed
1 Debugger armed
Note: This bit cannot be set if the DBGEN bit is not also being set at the same time. For example, a write of 01
to DBGEN[7:6] will be interpreted as a write of 00.
5
TRGSEL Trigger Selection Bit — The TRGSEL bit controls the triggering condition for comparators A and B in DBG
mode. It serves essentially the same function as the TAGAB bit in the DBGC2 register does in BKP mode. See
Section 16.4.2.1.2, “Trigger Selection, for more information. TRGSEL may also determine the type of breakpoint
based on comparator A and B if enabled in DBG mode (DBGBRK = 1). Please refer to Section 16.4.3.1,
“Breakpoint Based on Comparator A and B.”
0 Trigger on any compare address match
1 Trigger before opcode at compare address gets executed (tagged-type)
Chapter 16 Debug Module (DBGV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 483
4
BEGIN Begin/End Trigger Bit The BEGIN bit controls whether the trigger begins or ends storing of data in the trace
buffer. See Section 16.4.2.8.1, “Storing with Begin-Trigger,” and Section 16.4.2.8.2, “Storing with End-Trigger,”
for more details.
0 Trigger at end of stored data
1 Trigger before storing data
3
DBGBRK DBG Breakpoint Enable Bit The DBGBRK bit controls whether the debuggerwill request a breakpoint based
on comparator A and B to the CPU upon completion of a tracing session. Please refer to Section 16.4.3,
“Breakpoints,” for further details.
0 CPU break request not enabled
1 CPU break request enabled
1:0
CAPMOD Capture Mode Field — See Table 16-4 for capture mode field definitions. In LOOP1 mode, the debugger will
automatically inhibit redundant entries into capture memory. In detail mode, the debugger is storing address and
data for all cycles except program fetch (P) and free (f) cycles. In profile mode, the debugger is returning the
address of the last instruction executed by the CPU on each access of trace buffer address. Refer to
Section 16.4.2.6, “Capture Modes,” for more information.
Table 16-4. CAPMOD Encoding
CAPMOD Description
00 Normal
01 LOOP1
10 DETAIL
11 PROFILE
Table 16-3. DBGC1 Field Descriptions (continued)
Field Description
Chapter 16 Debug Module (DBGV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
484 Freescale Semiconductor
16.3.2.2 Debug Status and Control Register (DBGSC)
Module Base + 0x0021
Starting address location affected by INITRG register setting.
76543210
RAF BF CF 0 TRG
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 16-5. Debug Status and Control Register (DBGSC)
Table 16-5. DBGSC Field Descriptions
Field Description
7
AF Trigger A Match Flag — The AF bit indicates if trigger A match condition was met since arming. This bit is
cleared when ARM in DBGC1 is written to a 1 or on any write to this register.
0 Trigger A did not match
1 Trigger A match
6
BF Trigger B Match Flag — The BF bit indicates if trigger B match condition was met since arming.This bit is
cleared when ARM in DBGC1 is written to a 1 or on any write to this register.
0 Trigger B did not match
1 Trigger B match
5
CF Comparator C Match Flag The CF bit indicates if comparator C match condition was met since arming.This
bit is cleared when ARM in DBGC1 is written to a 1 or on any write to this register.
0 Comparator C did not match
1 Comparator C match
3:0
TRG Trigger Mode Bits — The TRG bits select the trigger mode of the DBG module as shown Table 16-6. See
Section 16.4.2.5, “Trigger Modes,” for more detail.
Table 16-6. Trigger Mode Encoding
TRG Value Meaning
0000 A only
0001 A or B
0010 A then B
0011 Event only B
0100 A then event only B
0101 A and B (full mode)
0110 A and Not B (full mode)
0111 Inside range
1000 Outside range
1001
1111
Reserved
(Defaults to A only)
Chapter 16 Debug Module (DBGV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 485
16.3.2.3 Debug Trace Buffer Register (DBGTB)
Module Base + 0x0022
Starting address location affected by INITRG register setting.
15 14 13 12 11 10 9 8
R Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8
W
Reset u u u uuuuu
= Unimplemented or Reserved
Figure 16-6. Debug Trace Buffer Register High (DBGTBH)
Module Base + 0x0023
Starting address location affected by INITRG register setting.
76543210
R Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
W
Reset u u u uuuuu
= Unimplemented or Reserved
Figure 16-7. Debug Trace Buffer Register Low (DBGTBL)
Table 16-7. DBGTB Field Descriptions
Field Description
15:0 Trace Buffer Data Bits The trace buffer data bits contain the data of the trace buffer. This register can be read
only as a word read. Any byte reads or misaligned access of these registers will return 0 and will not cause the
trace buffer pointer to increment to the next trace buffer address. The same is true for word reads while the
debugger is armed. In addition, this register may appear to contain incorrect data if it is not read with the same
capture mode bit settings as when the trace buffer data was recorded (See Section 16.4.2.9, “Reading Data from
Trace Buffer”). Because reads will reflect the contents of the trace buffer RAM, the reset state is undefined.
Chapter 16 Debug Module (DBGV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
486 Freescale Semiconductor
16.3.2.4 Debug Count Register (DBGCNT)
Module Base + 0x0024
Starting address location affected by INITRG register setting.
76543210
R TBF 0 CNT
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 16-8. Debug Count Register (DBGCNT)
Table 16-8. DBGCNT Field Descriptions
Field Description
7
TBF Trace Buffer Full The TBF bit indicates that the trace buffer has stored 64 or more words of data since it was
last armed. If this bit is set, then all 64 words will be valid data, regardless of the value in CNT[5:0]. The TBF bit
is cleared when ARM in DBGC1 is written to a 1.
5:0
CNT Count Value TheCNT bits indicatethe numberof validdatawords storedin the tracebuffer.Table 16-9shows
the correlation between the CNT bits and the number of valid data words in the trace buffer. When the CNT rolls
over to 0, the TBF bit will be set and incrementing of CNT will continue if DBG is in end-trigger mode. The
DBGCNT register is cleared when ARM in DBGC1 is written to a 1.
Table 16-9. CNT Decoding Table
TBF CNT Description
0 000000 No data valid
0 000001 1 word valid
0 000010
..
..
111110
2 words valid
..
..
62 words valid
0 111111 63 words valid
1 000000 64 words valid; if BEGIN = 1, the
ARM bit will be cleared. A
breakpoint will be generated if
DBGBRK = 1
1 000001
..
..
111111
64 words valid,
oldest data has been overwritten
by most recent data
Chapter 16 Debug Module (DBGV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 487
16.3.2.5 Debug Comparator C Extended Register (DBGCCX)
Module Base + 0x0025
Starting address location affected by INITRG register setting.
76543210
RPAGSEL EXTCMP
W
Reset 0 0 0 00000
Figure 16-9. Debug Comparator C Extended Register (DBGCCX)
Table 16-10. DBGCCX Field Descriptions
Field Description
7:6
PAGSEL Page Selector Field — In both BKP and DBG mode, PAGSEL selects the type of paging as shown in
Table 16-11.
DPAGE and EPAGE are not yet implemented so the value in bit 7 will be ignored (i.e., PAGSEL values of 10 and
11 will be interpreted as values of 00 and 01, respectively).
5:0
EXTCMP Comparator C Extended Compare Bits The EXTCMP bits are used as comparison address bits as shown
in Table 16-11 along with the appropriate PPAGE, DPAGE, or EPAGE signal from the core.
Note: Comparator C can be used when the DBG module is configured for BKP mode. Extended addressing
comparisons for comparator C use PAGSEL and will operate differently to the way that comparator A and
B operate in BKP mode.
Table 16-11. PAGSEL Decoding1
1See Figure 16-10.
PAGSEL Description EXTCMP Comment
00 Normal (64k) Not used No paged memory
01 PPAGE
(256 — 16K pages) EXTCMP[5:0] is compared to
address bits [21:16]2
2Current HCS12 implementations have PPAGE limited to 6 bits. Therefore, EXTCMP[5:4] should be set to 00.
PPAGE[7:0] / XAB[21:14] becomes
address bits [21:14]1
103
3Data page (DPAGE) and Extra page (EPAGE) are reserved for implementation on devices that support paged data and extra
space.
DPAGE (reserved)
(256 — 4K pages) EXTCMP[3:0] is compared to
address bits [19:16] DPAGE / XAB[21:14] becomes address
bits [19:12]
112EPAGE (reserved)
(256 — 1K pages) EXTCMP[1:0] is compared to
address bits [17:16] EPAGE / XAB[21:14] becomes address
bits [17:10]
Chapter 16 Debug Module (DBGV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
488 Freescale Semiconductor
16.3.2.6 Debug Comparator C Register (DBGCC)
DBGCXX DBGCXH[15:12]
PAGSEL EXTCMP BIT 15 BIT 14 BIT 13 BIT 12
76
0
50
43 2 1 BIT 0
SEE NOTE 1
PORTK/XAB XAB21 XAB20 XAB19 XAB18 XAB17 XAB16 XAB15 XAB14
PPAGE PIX7 PIX6 PIX5 PIX4 PIX3 PIX2 PIX1 PIX0
SEE NOTE 2
NOTES:
1. In BKP and DBG mode, PAGSEL selects the type of paging as shown in Table 16-11.
2. Current HCS12 implementations are limited to six PPAGE bits, PIX[5:0]. Therefore, EXTCMP[5:4] = 00.
Figure 16-10. Comparator C Extended Comparison in BKP/DBG Mode
Module Base + 0x0026
Starting address location affected by INITRG register setting.
15 14 13 12 11 10 9 8
R Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 16-11. Debug Comparator C Register High (DBGCCH)
Module Base + 0x0027
Starting address location affected by INITRG register setting.
76543210
R Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 16-12. Debug Comparator C Register Low (DBGCCL)
BKP/DBG MODE
Chapter 16 Debug Module (DBGV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 489
16.3.2.7 Debug Control Register 2 (DBGC2)
Figure 16-13. Debug Control Register 2 (DBGC2)
Table 16-12. DBGCC Field Descriptions
Field Description
15:0 Comparator C Compare Bits — The comparator C compare bits control whether comparator C will compare
the address bus bits [15:0] to a logic 1 or logic 0. See Table 16-13.
0 Compare corresponding address bit to a logic 0
1 Compare corresponding address bit to a logic 1
Note: This register will be cleared automatically when the DBG module is armed in LOOP1 mode.
Table 16-13. Comparator C Compares
PAGSEL EXTCMP Compare High-Byte Compare
x0 No compare DBGCCH[7:0] = AB[15:8]
x1 EXTCMP[5:0] = XAB[21:16] DBGCCH[7:0] = XAB[15:14],AB[13:8]
Module Base + 0x0028
Starting address location affected by INITRG register setting.
76543210
RBKABEN1
1When BKABEN is set (BKP mode), all bits in DBGC2 are available. When BKABEN is cleared and DBG is used in DBG mode,
bits FULL and TAGAB have no meaning.
FULL BDM TAGAB BKCEN2
2These bits can be used in BKP mode and DBG mode (when capture mode is not set in LOOP1) to provide a third breakpoint.
TAGC2RWCEN2RWC2
W
Reset 0 0 0 00000
Table 16-14. DBGC2 Field Descriptions
Field Description
7
BKABEN Breakpoint Using Comparator A and B Enable This bit enables the breakpoint capability using comparator
A and B, when set (BKP mode) the DBGEN bit in DBGC1 cannot be set.
0 Breakpoint module off
1 Breakpoint module on
6
FULL Full Breakpoint Mode Enable This bit controls whether the breakpoint module is in dual mode or full mode.
In full mode, comparator A is used to match address and comparator B is used to match data. See
Section 16.4.1.2, “Full Breakpoint Mode,” for more details.
0 Dual address mode enabled
1 Full breakpoint mode enabled
5
BDM Background Debug Mode Enable — This bit determines if the breakpoint causes the system to enter
background debug mode (BDM) or initiate a software interrupt (SWI).
0 Go to software interrupt on a break request
1 Go to BDM on a break request
Chapter 16 Debug Module (DBGV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
490 Freescale Semiconductor
16.3.2.8 Debug Control Register 3 (DBGC3)
Figure 16-14. Debug Control Register 3 (DBGC3)
4
TAGAB Comparator A/B Tag Select Thisbit controls whetherthe breakpoint willcause a breakon the nextinstruction
boundary (force) or on a match that will be an executable opcode (tagged). Non-executed opcodes cannot cause
a tagged breakpoint.
0 On match, break at the next instruction boundary (force)
1 On match, break if/when the instruction is about to be executed (tagged)
3
BKCEN Breakpoint Comparator C Enable Bit — This bit enables the breakpoint capability using comparator C.
0 Comparator C disabled for breakpoint
1 Comparator C enabled for breakpoint
Note: This bit will be cleared automatically when the DBG module is armed in loop1 mode.
2
TAGC Comparator C Tag Select This bit controls whether the breakpoint will cause a break on the next instruction
boundary (force) or on a match that will be an executable opcode (tagged). Non-executed opcodes cannot cause
a tagged breakpoint.
0 On match, break at the next instruction boundary (force)
1 On match, break if/when the instruction is about to be executed (tagged)
1
RWCEN Read/Write Comparator C Enable Bit The RWCEN bit controls whether read or write comparison is enabled
for comparator C. RWCEN is not useful for tagged breakpoints.
0 Read/Write is not used in comparison
1 Read/Write is used in comparison
0
RWC Read/Write Comparator C Value Bit — The RWC bit controls whether read or write is used in compare for
comparator C. The RWC bit is not used if RWCEN = 0.
0 Write cycle will be matched
1 Read cycle will be matched
Module Base + 0x0029
Starting address location affected by INITRG register setting.
76543210
RBKAMBH1
1In DBG mode, BKAMBH:BKAMBL has no meaning and are forced to 0’s.
BKAMBL1BKBMBH2
2In DBG mode, BKBMBH:BKBMBL are used in full mode to qualify data.
BKBMBL2RWAEN RWA RWBEN RWB
W
Reset 0 0 0 00000
Table 16-14. DBGC2 Field Descriptions (continued)
Field Description
Chapter 16 Debug Module (DBGV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 491
Table 16-15. DBGC3 Field Descriptions
Field Description
7:6
BKAMB[H:L] Breakpoint Mask High Byte for First Address In dual or full mode, these bits may be used to mask (disable)
the comparison of the high and/or low bytes of the first address breakpoint. The functionality is as given in
Table 16-16.
The x:0 case is for a full address compare. When a program page is selected, the full address compare will be
based on bits for a 20-bit compare. The registers used for the compare are {DBGCAX[5:0], DBGCAH[5:0],
DBGCAL[7:0]}, where DBGAX[5:0] corresponds to PPAGE[5:0] or extended address bits [19:14] and CPU
address [13:0]. When a program page is not selected, the full address compare will be based on bits for a 16-bit
compare. The registers used for the compare are {DBGCAH[7:0], DBGCAL[7:0]} which corresponds to CPU
address [15:0].
Note: This extended address compare scheme causes an aliasing problem in BKP mode in which several
physical addresses may match with a single logical address. This problem may be avoided by using DBG
mode to generate breakpoints.
The 1:0 case is not sensible because it would ignore the high order address and compare the low order and
expansion addresses. Logic forces this case to compare all address lines (effectively ignoring the BKAMBH
control bit).
The 1:1 case is useful for triggering a breakpoint on any access to a particular expansion page. This only makes
sense if a program page is being accessed so that the breakpoint trigger will occur only if DBGCAX compares.
5:4
BKBMB[H:L] Breakpoint Mask High Byte and Low Byte of Data (Second Address) — In dual mode, these bits may be
used to mask (disable) the comparison of the high and/or low bytes of the second address breakpoint. The
functionality is as given in Table 16-17.
The x:0 case is for a full address compare. When a program page is selected, the full address compare will be
based on bits for a 20-bit compare. The registers used for the compare are {DBGCBX[5:0], DBGCBH[5:0],
DBGCBL[7:0]} where DBGCBX[5:0] corresponds to PPAGE[5:0] or extended address bits [19:14] and CPU
address [13:0]. When a program page is not selected, the full address compare will be based on bits for a 16-bit
compare. The registers used for the compare are {DBGCBH[7:0], DBGCBL[7:0]} which corresponds to CPU
address [15:0].
Note: This extended address compare scheme causes an aliasing problem in BKP mode in which several
physical addresses may match with a single logical address. This problem may be avoided by using DBG
mode to generate breakpoints.
The 1:0 case is not sensible because it would ignore the high order address and compare the low order and
expansion addresses. Logic forces this case to compare all address lines (effectively ignoring the BKBMBH
control bit).
The 1:1 case is useful for triggering a breakpoint on any access to a particular expansion page. This only makes
sense if a program page is being accessed so that the breakpoint trigger will occur only if DBGCBX compares.
In full mode, these bits may be used to mask (disable) the comparison of the high and/or low bytes of the data
breakpoint. The functionality is as given in Table 16-18.
3
RWAEN Read/Write Comparator A Enable Bit The RWAEN bit controls whether read or write comparison is enabled
forcomparator A.SeeSection 16.4.2.1.1, “Reador Write Comparison, formoreinformation.This bitis not useful
for tagged operations.
0 Read/Write is not used in comparison
1 Read/Write is used in comparison
2
RWA Read/Write Comparator A Value Bit — The RWA bit controls whether read or write is used in compare for
comparator A. The RWA bit is not used if RWAEN = 0.
0 Write cycle will be matched
1 Read cycle will be matched
Chapter 16 Debug Module (DBGV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
492 Freescale Semiconductor
1
RWBEN Read/Write Comparator B Enable Bit The RWBEN bit controls whether read or write comparison is enabled
forcomparator B.SeeSection 16.4.2.1.1, “Reador Write Comparison, formoreinformation.This bitis not useful
for tagged operations.
0 Read/Write is not used in comparison
1 Read/Write is used in comparison
0
RWB Read/Write Comparator B Value Bit — The RWB bit controls whether read or write is used in compare for
comparator B. The RWB bit is not used if RWBEN = 0.
0 Write cycle will be matched
1 Read cycle will be matched
Note: RWB and RWBEN are not used in full mode.
Table 16-16. Breakpoint Mask Bits for First Address
BKAMBH:BKAMBL Address Compare DBGCAX DBGCAH DBGCAL
x:0 Full address compare Yes1
1If PPAGE is selected.
Yes Yes
0:1 256 byte address range Yes1Yes No
1:1 16K byte address range Yes1No No
Table 16-17. Breakpoint Mask Bits for Second Address (Dual Mode)
BKBMBH:BKBMBL Address Compare DBGCBX DBGCBH DBGCBL
x:0 Full address compare Yes1
1If PPAGE is selected.
Yes Yes
0:1 256 byte address range Yes1Yes No
1:1 16K byte address range Yes1No No
Table 16-18. Breakpoint Mask Bits for Data Breakpoints (Full Mode)
BKBMBH:BKBMBL Data Compare DBGCBX DBGCBH DBGCBL
0:0 High and low byte compare No1
1Expansion addresses for breakpoint B are not applicable in this mode.
Yes Yes
0:1 High byte No1Yes No
1:0 Low byte No1No Yes
1:1 No compare No1No No
Table 16-15. DBGC3 Field Descriptions (continued)
Field Description
Chapter 16 Debug Module (DBGV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 493
16.3.2.9 Debug Comparator A Extended Register (DBGCAX)
Module Base + 0x002A
Starting address location affected by INITRG register setting.
76543210
RPAGSEL EXTCMP
W
Reset 0 0 0 00000
Figure 16-15. Debug Comparator A Extended Register (DBGCAX)
Table 16-19. DBGCAX Field Descriptions
Field Description
7:6
PAGSEL Page Selector Field — If DBGEN is set in DBGC1, then PAGSEL selects the type of paging as shown in
Table 16-20.
DPAGE and EPAGE are not yet implemented so the value in bit 7 will be ignored (i.e., PAGSEL values of 10 and
11 will be interpreted as values of 00 and 01, respectively).
In BKP mode, PAGSEL has no meaning and EXTCMP[5:0] are compared to address bits [19:14] if the address
is in the FLASH/ROM memory space.
5:0
EXTCMP Comparator A Extended Compare Bits The EXTCMP bits are used as comparison address bits as shown
in Table 16-20 along with the appropriate PPAGE, DPAGE, or EPAGE signal from the core.
Table 16-20. Comparator A or B Compares
Mode EXTCMP Compare High-Byte Compare
BKP1
1See Figure 16-16.
Not FLASH/ROM access No compare DBGCxH[7:0] = AB[15:8]
FLASH/ROM access EXTCMP[5:0] = XAB[19:14] DBGCxH[5:0] = AB[13:8]
DBG2
2See Figure 16-10 (note that while this figure provides extended comparisons for comparator C, the figure also pertains to
comparators A and B in DBG mode only).
PAGSEL = 00 No compare DBGCxH[7:0] = AB[15:8]
PAGSEL = 01 EXTCMP[5:0] = XAB[21:16] DBGCxH[7:0] = XAB[15:14], AB[13:8]
Chapter 16 Debug Module (DBGV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
494 Freescale Semiconductor
16.3.2.10 Debug Comparator A Register (DBGCA)
PAGSEL EXTCMP
DBGCXX 0 0 54321BIT 0
SEE NOTE 1
PORTK/XAB XAB21 XAB20 XAB19 XAB18 XAB17 XAB16 XAB15 XAB14
PPAGE PIX7 PIX6 PIX5 PIX4 PIX3 PIX2 PIX1 PIX0
SEE NOTE 2
NOTES:
1. In BKP mode, PAGSEL has no functionality. Therefore, set PAGSEL to 00 (reset state).
2. Current HCS12 implementations are limited to six PPAGE bits, PIX[5:0].
Figure 16-16. Comparators A and B Extended Comparison in BKP Mode
Module Base + 0x002B
Starting address location affected by INITRG register setting.
15 14 13 12 11 10 9 8
RBit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8
W
Reset 0 0 0 00000
Figure 16-17. Debug Comparator A Register High (DBGCAH)
Module Base + 0x002C
Starting address location affected by INITRG register setting.
76543210
RBit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
W
Reset 0 0 0 00000
Figure 16-18. Debug Comparator A Register Low (DBGCAL)
Table 16-21. DBGCA Field Descriptions
Field Description
15:0
15:0 Comparator A Compare Bits The comparator A compare bits control whether comparator A compares the
address bus bits [15:0] to a logic 1 or logic 0. See Table 16-20.
0 Compare corresponding address bit to a logic 0
1 Compare corresponding address bit to a logic 1
BKP MODE
Chapter 16 Debug Module (DBGV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 495
16.3.2.11 Debug Comparator B Extended Register (DBGCBX)
16.3.2.12 Debug Comparator B Register (DBGCB)
Module Base + 0x002D
76543210
RPAGSEL EXTCMP
W
Reset 0 0 0 00000
Figure 16-19. Debug Comparator B Extended Register (DBGCBX)
Table 16-22. DBGCBX Field Descriptions
Field Description
7:6
PAGSEL Page Selector Field — If DBGEN is set in DBGC1, then PAGSEL selects the type of paging as shown in
Table 16-11.
DPAGE and EPAGE are not yet implemented so the value in bit 7 will be ignored (i.e., PAGSEL values of 10 and
11 will be interpreted as values of 00 and 01, respectively.)
In BKP mode, PAGSEL has no meaning and EXTCMP[5:0] are compared to address bits [19:14] if the address
is in the FLASH/ROM memory space.
5:0
EXTCMP Comparator B Extended Compare Bits The EXTCMP bits are used as comparison address bits as shown
in Table 16-11 along with the appropriate PPAGE, DPAGE, or EPAGE signal from the core. Also see Table 16-20.
Module Base + 0x002E
Starting address location affected by INITRG register setting.
15 14 13 12 11 10 9 8
RBit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8
W
Reset 0 0 0 00000
Figure 16-20. Debug Comparator B Register High (DBGCBH)
Chapter 16 Debug Module (DBGV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
496 Freescale Semiconductor
16.4 Functional Description
This section provides a complete functional description of the DBG module. The DBG module can be
configured to run in either of two modes, BKP or DBG. BKP mode is enabled by setting BKABEN in
DBGC2. DBG mode is enabled by setting DBGEN in DBGC1. Setting BKABEN in DBGC2 overrides the
DBGEN in DBGC1 and prevents DBG mode. If the part is in secure mode, DBG mode cannot be enabled.
16.4.1 DBG Operating in BKP Mode
In BKP mode, the DBG will be fully backwards compatible with the existing BKP_ST12_A module. The
DBGC2 register has four additional bits that were not available on existing BKP_ST12_A modules. As
long as these bits are written to either all 1s or all 0s, they should be transparent to the user. All 1s would
enable comparator C to be used as a breakpoint, but tagging would be enabled. The match address register
would be all 0s if not modified by the user. Therefore, code executing at address 0x0000 would have to
occur before a breakpoint based on comparator C would happen.
The DBG module in BKP mode supports two modes of operation: dual address mode and full breakpoint
mode. Within each of these modes, forced or tagged breakpoint types can be used. Forced breakpoints
occur at the next instruction boundary if a match occurs and tagged breakpoints allow for breaking just
before the tagged instruction executes. The action taken upon a successful match can be to either place the
CPU in background debug mode or to initiate a software interrupt.
The breakpoint can operate in dual address mode or full breakpoint mode. Each of these modes is
discussed in the subsections below.
16.4.1.1 Dual Address Mode
When dual address mode is enabled, two address breakpoints can be set. Each breakpoint can cause the
system to enter background debug mode or to initiate a software interrupt based upon the state of BDM in
Module Base + 0x002F
Starting address location affected by INITRG register setting.
76543210
RBit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
W
Reset 0 0 0 00000
Figure 16-21. Debug Comparator B Register Low (DBGCBL)
Table 16-23. DBGCB Field Descriptions
Field Description
15:0
15:0 Comparator B Compare Bits The comparator B compare bits control whether comparator B compares the
address bus bits [15:0] or data bus bits [15:0] to a logic 1 or logic 0. See Table 16-20.
0 Compare corresponding address bit to a logic 0, compares to data if in Full mode
1 Compare corresponding address bit to a logic 1, compares to data if in Full mode
Chapter 16 Debug Module (DBGV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 497
DBGC2 being logic 1 or logic 0, respectively. BDM requests have a higher priority than SWI requests. No
data breakpoints are allowed in this mode.
TAGAB in DBGC2 selects whether the breakpoint mode is forced or tagged. The BKxMBH:L bits in
DBGC3 select whether or not the breakpoint is matched exactly or is a range breakpoint. They also select
whether the address is matched on the high byte, low byte, both bytes, and/or memory expansion. The
RWx and RWxEN bits in DBGC3 select whether the type of bus cycle to match is a read, write, or
read/write when performing forced breakpoints.
16.4.1.2 Full Breakpoint Mode
Full breakpoint mode requires a match on address and data for a breakpoint to occur. Upon a successful
match, the system will enter background debug mode or initiate a software interrupt based upon the state
of BDM in DBGC2 being logic 1 or logic 0, respectively. BDM requests have a higher priority than SWI
requests. R/W matches are also allowed in this mode.
TAGAB in DBGC2 selects whether the breakpoint mode is forced or tagged. When TAGAB is set in
DBGC2, only addresses are compared and data is ignored. The BKAMBH:L bits in DBGC3 select
whether or not the breakpoint is matched exactly, is a range breakpoint, or is in page space. The
BKBMBH:L bits in DBGC3 select whether the data is matched on the high byte, low byte, or both bytes.
RWA and RWAEN bits in DBGC2 select whether the type of bus cycle to match is a read or a write when
performing forced breakpoints. RWB and RWBEN bits in DBGC2 are not used in full breakpoint mode.
NOTE
The full trigger mode is designed to be used for either a word access or a
byte access, but not both at the same time. Confusing trigger operation
(seemingly false triggers or no trigger) can occur if the trigger address
occurs in the user program as both byte and word accesses.
16.4.1.3 Breakpoint Priority
Breakpoint operation is first determined by the state of the BDM module. If the BDM module is already
active, meaning the CPU is executing out of BDM firmware, breakpoints are not allowed. In addition,
while executing a BDM TRACE command, tagging into BDM is not allowed. If BDM is not active, the
breakpoint will give priority to BDM requests over SWI requests. This condition applies to both forced
and tagged breakpoints.
In all cases, BDM related breakpoints will have priority over those generated by the Breakpoint sub-block.
This priority includes breakpoints enabled by the TAGLO and TAGHI external pins of the system that
interface with the BDM directly and whose signal information passes through and is used by the
breakpoint sub-block.
Chapter 16 Debug Module (DBGV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
498 Freescale Semiconductor
NOTE
BDM should not be entered from a breakpoint unless the ENABLE bit is set
in the BDM. Even if the ENABLE bit in the BDM is cleared, the CPU
actually executes the BDM firmware code. It checks the ENABLE and
returns if ENABLE is not set. If the BDM is not serviced by the monitor then
the breakpoint would be re-asserted when the BDM returns to normal CPU
flow.
There is no hardware to enforce restriction of breakpoint operation if the
BDM is not enabled.
When program control returns from a tagged breakpoint through an RTI or
a BDM GO command, it will return to the instruction whose tag generated
the breakpoint. Unless breakpoints are disabled or modified in the service
routine or active BDM session, the instruction will be tagged again and the
breakpoint will be repeated. In the case of BDM breakpoints, this situation
can also be avoided by executing a TRACE1 command before the GO to
increment the program flow past the tagged instruction.
16.4.1.4 Using Comparator C in BKP Mode
The original BKP_ST12_A module supports two breakpoints. The DBG_ST12_A module can be used in
BKP mode and allow a third breakpoint using comparator C. Four additional bits, BKCEN, TAGC,
RWCEN, and RWC in DBGC2 in conjunction with additional comparator C address registers, DBGCCX,
DBGCCH, and DBGCCL allow the user to set up a third breakpoint. Using PAGSEL in DBGCCX for
expanded memory will work differently than the way paged memory is done using comparator A and B in
BKP mode. See Section 16.3.2.5, “Debug Comparator C Extended Register (DBGCCX),” for more
information on using comparator C.
16.4.2 DBG Operating in DBG Mode
Enabling the DBG module in DBG mode, allows the arming, triggering, and storing of data in the trace
buffer and can be used to cause CPU breakpoints. The DBG module is made up of three main blocks, the
comparators, trace buffer control logic, and the trace buffer.
NOTE
In general, there is a latency between the triggering event appearing on the
bus and being detected by the DBG circuitry. In general, tagged triggers will
be more predictable than forced triggers.
16.4.2.1 Comparators
The DBG contains three comparators, A, B, and C. Comparator A compares the core address bus with the
address stored in DBGCAH and DBGCAL. Comparator B compares the core address bus with the address
stored in DBGCBH and DBGCBL except in full mode, where it compares the data buses to the data stored
in DBGCBH and DBGCBL. Comparator C can be used as a breakpoint generator or as the address
comparison unit in the loop1 mode. Matches on comparator A, B, and C are signaled to the trace buffer
Chapter 16 Debug Module (DBGV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 499
control (TBC) block. When PAGSEL = 01, registers DBGCAX, DBGCBX, and DBGCCX are used to
match the upper addresses as shown in Table 16-11.
NOTE
If a tagged-type C breakpoint is set at the same address as an A/B
tagged-type trigger (including the initial entry in an inside or outside range
trigger), the C breakpoint will have priority and the trigger will not be
recognized.
16.4.2.1.1 Read or Write Comparison
Read or write comparisons are useful only with TRGSEL = 0, because only opcodes should be tagged as
they are “read” from memory. RWAEN and RWBEN are ignored when TRGSEL = 1.
In full modes (“A and B” and “A and not B”) RWAEN and RWA are used to select read or write
comparisons for both comparators A and B. Table 16-24 shows the effect for RWAEN, RWA, and RW on
the DBGCB comparison conditions. The RWBEN and RWB bits are not used and are ignored in full
modes.
16.4.2.1.2 Trigger Selection
The TRGSEL bit in DBGC1 is used to determine the triggering condition in DBG mode. TRGSEL applies
to both trigger A and B except in the event only trigger modes. By setting TRGSEL, the comparators A
and B will qualify a match with the output of opcode tracking logic and a trigger occurs before the tagged
instruction executes (tagged-type trigger). With the TRGSEL bit cleared, a comparator match forces a
trigger when the matching condition occurs (force-type trigger).
NOTE
If the TRGSEL is set, the address stored in the comparator match address
registers must be an opcode address for the trigger to occur.
16.4.2.2 Trace Buffer Control (TBC)
The TBC is the main controller for the DBG module. Its function is to decide whether data should be stored
in the trace buffer based on the trigger mode and the match signals from the comparator. The TBC also
determines whether a request to break the CPU should occur.
Table 16-24. Read or Write Comparison Logic Table
RWAEN bit RWA bit RW signal Comment
0 x 0 Write data bus
0 x 1 Read data bus
1 0 0 Write data bus
1 0 1 No data bus compare since RW=1
1 1 0 No data bus compare since RW=0
1 1 1 Read data bus
Chapter 16 Debug Module (DBGV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
500 Freescale Semiconductor
16.4.2.3 Begin- and End-Trigger
The definitions of begin- and end-trigger as used in the DBG module are as follows:
Begin-trigger: Storage in trace buffer occurs after the trigger and continues until 64 locations are
filled.
End-trigger: Storage in trace buffer occurs until the trigger, with the least recent data falling out of
the trace buffer if more than 64 words are collected.
16.4.2.4 Arming the DBG Module
In DBG mode, arming occurs by setting DBGEN and ARM in DBGC1. The ARM bit in DBGC1 is cleared
when the trigger condition is met in end-trigger mode or when the Trace Buffer is filled in begin-trigger
mode. The TBC logic determines whether a trigger condition has been met based on the trigger mode and
the trigger selection.
16.4.2.5 Trigger Modes
The DBG module supports nine trigger modes. The trigger modes are encoded as shown in Table 16-6.
The trigger mode is used as a qualifier for either starting or ending the storing of data in the trace buffer.
When the match condition is met, the appropriate flag A or B is set in DBGSC. Arming the DBG module
clears the A, B, and C flags in DBGSC. In all trigger modes except for the event-only modes and DETAIL
capture mode, change-of-flow addresses are stored in the trace buffer. In the event-only modes only the
value on the data bus at the trigger event B will be stored. In DETAIL capture mode address and data for
all cycles except program fetch (P) and free (f) cycles are stored in trace buffer.
16.4.2.5.1 A Only
In the A only trigger mode, if the match condition for A is met, the A flag in DBGSC is set and a trigger
occurs.
16.4.2.5.2 A or B
In the A or B trigger mode, if the match condition for A or B is met, the corresponding flag in DBGSC is
set and a trigger occurs.
16.4.2.5.3 A then B
In the A then B trigger mode, the match condition for A must be met before the match condition for B is
compared. When the match condition for A or B is met, the corresponding flag in DBGSC is set. The
trigger occurs only after A then B have matched.
NOTE
When tagging and using A then B, if addresses A and B are close together,
then B may not complete the trigger sequence. This occurs when A and B
are in the instruction queue at the same time. Basically the A trigger has not
yet occurred, so the B instruction is not tagged. Generally, if address B is at
Chapter 16 Debug Module (DBGV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 501
least six addresses higher than address A (or B is lower than A) and there
are not changes of flow to put these in the queue at the same time, then this
operation should trigger properly.
16.4.2.5.4 Event-Only B (Store Data)
In the event-only B trigger mode, if the match condition for B is met, the B flag in DBGSC is set and a
trigger occurs. The event-only B trigger mode is considered a begin-trigger type and the BEGIN bit in
DBGC1 is ignored. Event-only B is incompatible with instruction tagging (TRGSEL = 1), and thus the
value of TRGSEL is ignored. Please refer to Section 16.4.2.7, “Storage Memory,” for more information.
This trigger mode is incompatible with the detail capture mode so the detail capture mode will have
priority. TRGSEL and BEGIN will not be ignored and this trigger mode will behave as if it were “B only”.
16.4.2.5.5 A then Event-Only B (Store Data)
In the A then event-only B trigger mode, the match condition for A must be met before the match condition
for B is compared, after the A match has occurred, a trigger occurs each time B matches. When the match
condition for A or B is met, the corresponding flag in DBGSC is set. The A then event-only B trigger mode
is considered a begin-trigger type and BEGIN in DBGC1 is ignored. TRGSEL in DBGC1 applies only to
the match condition for A. Please refer to Section 16.4.2.7, “Storage Memory,” for more information.
This trigger mode is incompatible with the detail capture mode so the detail capture mode will have
priority. TRGSEL and BEGIN will not be ignored and this trigger mode will be the same as A then B.
16.4.2.5.6 A and B (Full Mode)
In the A and B trigger mode, comparator A compares to the address bus and comparator B compares to
the data bus. In the A and B trigger mode, if the match condition for A and B happen on the same bus cycle,
both the A and B flags in the DBGSC register are set and a trigger occurs.
If TRGSEL = 1, only matches from comparator A are used to determine if the trigger condition is met and
comparator B matches are ignored. If TRGSEL = 0, full-word data matches on an odd address boundary
(misaligned access) do not work unless the access is to a RAM that manages misaligned accesses in a
single clock cycle (which is typical of RAM modules used in HCS12 MCUs).
16.4.2.5.7 A and Not B (Full Mode)
In the A and not B trigger mode, comparator A compares to the address bus and comparator B compares
to the data bus. In the A and not B trigger mode, if the match condition for A and not B happen on the same
bus cycle, both the A and B flags in DBGSC are set and a trigger occurs.
If TRGSEL = 1, only matches from comparator A are used to determine if the trigger condition is met and
comparator B matches are ignored. As described in Section 16.4.2.5.6, A and B (Full Mode), full-word
data compares on misaligned accesses will not match expected data (and thus will cause a trigger in this
mode) unless the access is to a RAM that manages misaligned accesses in a single clock cycle.
Chapter 16 Debug Module (DBGV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
502 Freescale Semiconductor
16.4.2.5.8 Inside Range (A address B)
In the inside range trigger mode, if the match condition for A and B happen on the same bus cycle, both
the A and B flags in DBGSC are set and a trigger occurs. If a match condition on only A or only B occurs
no flags are set. If TRGSEL = 1, the inside range is accurate only to word boundaries. If TRGSEL = 0, an
aligned word access which straddles the range boundary will cause a trigger only if the aligned address is
within the range.
16.4.2.5.9 Outside Range (address < A or address > B)
In the outside range trigger mode, if the match condition for A or B is met, the corresponding flag in
DBGSC is set and a trigger occurs. If TRGSEL = 1, the outside range is accurate only to word boundaries.
If TRGSEL = 0, an aligned word access which straddles the range boundary will cause a trigger only if the
aligned address is outside the range.
16.4.2.5.10 Control Bit Priorities
The definitions of some of the control bits are incompatible with each other. Table 16-25 and the notes
associated with it summarize how these incompatibilities are managed:
Read/write comparisons are not compatible with TRGSEL = 1. Therefore, RWAEN and RWBEN
are ignored.
Event-only trigger modes are always considered a begin-type trigger. See Section 16.4.2.8.1,
“Storing with Begin-Trigger,” and Section 16.4.2.8.2, “Storing with End-Trigger.”
Detail capture mode has priority over the event-only trigger/capture modes. Therefore, event-only
modes have no meaning in detail mode and their functions default to similar trigger modes.
Table 16-25. Resolution of Mode Conflicts
Mode Normal / Loop1 Detail
Tag Force Tag Force
A only
A or B
A then B
Event-only B 1 1, 3 3
A then event-only B 2 4 4
A and B (full mode) 5 5
A and not B (full mode) 5 5
Inside range 6 6
Outside range 6 6
1 — Ignored — same as force
2 — Ignored for comparator B
3 — Reduces to effectively “B only”
4 — Works same as A then B
5 — Reduces to effectively “A only” — B not compared
6 — Only accurate to word boundaries
Chapter 16 Debug Module (DBGV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 503
16.4.2.6 Capture Modes
The DBG in DBG mode can operate in four capture modes. These modes are described in the following
subsections.
16.4.2.6.1 Normal Mode
In normal mode, the DBG module uses comparator A and B as triggering devices. Change-of-flow
information or data will be stored depending on TRG in DBGSC.
16.4.2.6.2 Loop1 Mode
The intent of loop1 mode is to prevent the trace buffer from being filled entirely with duplicate information
from a looping construct such as delays using the DBNE instruction or polling loops using
BRSET/BRCLR instructions. Immediately after address information is placed in the trace buffer, the DBG
module writes this value into the C comparator and the C comparator is placed in ignore address mode.
This will prevent duplicate address entries in the trace buffer resulting from repeated bit-conditional
branches. Comparator C will be cleared when the ARM bit is set in loop1 mode to prevent the previous
contents of the register from interfering with loop1 mode operation. Breakpoints based on comparator C
are disabled.
Loop1 mode only inhibits duplicate source address entries that would typically be stored in most tight
looping constructs. It will not inhibit repeated entries of destination addresses or vector addresses, because
repeated entries of these would most likely indicate a bug in the user’s code that the DBG module is
designed to help find.
NOTE
In certain very tight loops, the source address will have already been fetched
again before the C comparator is updated. This results in the source address
being stored twice before further duplicate entries are suppressed. This
condition occurs with branch-on-bit instructions when the branch is fetched
by the first P-cycle of the branch or with loop-construct instructions in
which the branch is fetched with the first or second P cycle. See examples
below:
LOOP INCX ; 1-byte instruction fetched by 1st P-cycle of BRCLR
BRCLR CMPTMP,#$0c,LOOP ; the BRCLR instruction also will be fetched by 1st P-cycle of BRCLR
LOOP2 BRN * ; 2-byte instruction fetched by 1st P-cycle of DBNE
NOP ; 1-byte instruction fetched by 2nd P-cycle of DBNE
DBNE A,LOOP2 ; this instruction also fetched by 2nd P-cycle of DBNE
NOTE
Loop1 mode does not support paged memory, and inhibits duplicate entries
in the trace buffer based solely on the CPU address. There is a remote
possibility of an erroneous address match if program flow alternates
between paged and unpaged memory space.
Chapter 16 Debug Module (DBGV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
504 Freescale Semiconductor
16.4.2.6.3 Detail Mode
In the detail mode, address and data for all cycles except program fetch (P) and free (f) cycles are stored
in trace buffer. This mode is intended to supply additional information on indexed, indirect addressing
modes where storing only the destination address would not provide all information required for a user to
determine where his code was in error.
16.4.2.6.4 Profile Mode
This mode is intended to allow a host computer to poll a running target and provide a histogram of program
execution. Each read of the trace buffer address will return the address of the last instruction executed. The
DBGCNT register is not incremented and the trace buffer does not get filled. The ARM bit is not used and
all breakpoints and all other debug functions will be disabled.
16.4.2.7 Storage Memory
The storage memory is a 64 words deep by 16-bits wide dual port RAM array. The CPU accesses the RAM
array through a single memory location window (DBGTBH:DBGTBL). The DBG module stores trace
information in the RAM array in a circular buffer format. As data is read via the CPU, a pointer into the
RAM will increment so that the next CPU read will receive fresh information. In all trigger modes except
for event-only and detail capture mode, the data stored in the trace buffer will be change-of-flow addresses.
change-of-flow addresses are defined as follows:
Source address of conditional branches (long, short, BRSET, and loop constructs) taken
Destination address of indexed JMP, JSR, and CALL instruction
Destination address of RTI, RTS, and RTC instructions
Vector address of interrupts except for SWI and BDM vectors
In the event-only trigger modes only the 16-bit data bus value corresponding to the event is stored. In the
detail capture mode, address and then data are stored for all cycles except program fetch (P) and free (f)
cycles.
16.4.2.8 Storing Data in Memory Storage Buffer
16.4.2.8.1 Storing with Begin-Trigger
Storing with begin-trigger can be used in all trigger modes. When DBG mode is enabled and armed in the
begin-trigger mode, data is not stored in the trace buffer until the trigger condition is met. As soon as the
trigger condition is met, the DBG module will remain armed until 64 words are stored in the trace buffer.
If the trigger is at the address of the change-of-flow instruction the change-of-flow associated with the
trigger event will be stored in the trace buffer.
16.4.2.8.2 Storing with End-Trigger
Storing with end-trigger cannot be used in event-only trigger modes. When DBG mode is enabled and
armed in the end-trigger mode, data is stored in the trace buffer until the trigger condition is met. When
the trigger condition is met, the DBG module will become de-armed and no more data will be stored. If
Chapter 16 Debug Module (DBGV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 505
the trigger is at the address of a change-of-flow address the trigger event will not be stored in the trace
buffer.
16.4.2.9 Reading Data from Trace Buffer
The data stored in the trace buffer can be read using either the background debug module (BDM) module
or the CPU provided the DBG module is enabled and not armed. The trace buffer data is read out first-in
first-out. By reading CNT in DBGCNT the number of valid words can be determined. CNT will not
decrement as data is read from DBGTBH:DBGTBL. The trace buffer data is read by reading
DBGTBH:DBGTBL with a 16-bit read. Each time DBGTBH:DBGTBL is read, a pointer in the DBG will
be incremented to allow reading of the next word.
Reading the trace buffer while the DBG module is armed will return invalid data and no shifting of the
RAM pointer will occur.
NOTE
The trace buffer should be read with the DBG module enabled and in the
same capture mode that the data was recorded. The contents of the trace
buffer counter register (DBGCNT) are resolved differently in detail mode
verses the other modes and may lead to incorrect interpretation of the trace
buffer data.
16.4.3 Breakpoints
There are two ways of getting a breakpoint in DBG mode. One is based on the trigger condition of the
trigger mode using comparator A and/or B, and the other is using comparator C. External breakpoints
generated using the TAGHI and TAGLO external pins are disabled in DBG mode.
16.4.3.1 Breakpoint Based on Comparator A and B
A breakpoint request to the CPU can be enabled by setting DBGBRK in DBGC1. The value of BEGIN in
DBGC1 determines when the breakpoint request to the CPU will occur. When BEGIN in DBGC1 is set,
begin-trigger is selected and the breakpoint request will not occur until the trace buffer is filled with
64 words. When BEGIN in DBGC1 is cleared, end-trigger is selected and the breakpoint request will occur
immediately at the trigger cycle.
There are two types of breakpoint requests supported by the DBG module, tagged and forced. Tagged
breakpoints are associated with opcode addresses and allow breaking just before a specific instruction
executes. Forced breakpoints are not associated with opcode addresses and allow breaking at the next
instruction boundary. The type of breakpoint based on comparators A and B is determined by TRGSEL in
the DBGC1 register (TRGSEL = 1 for tagged breakpoint, TRGSEL = 0 for forced breakpoint).
Table 16-26 illustrates the type of breakpoint that will occur based on the debug run.
Chapter 16 Debug Module (DBGV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
506 Freescale Semiconductor
16.4.3.2 Breakpoint Based on Comparator C
A breakpoint request to the CPU can be created if BKCEN in DBGC2 is set. Breakpoints based on a
successful comparator C match can be accomplished regardless of the mode of operation for comparator
A or B, and do not affect the status of the ARM bit. TAGC in DBGC2 is used to select either tagged or
forced breakpoint requests for comparator C. Breakpoints based on comparator C are disabled in LOOP1
mode.
NOTE
Because breakpoints cannot be disabled when the DBG is armed, one must
be careful to avoid an “infinite breakpoint loop” when using tagged-type C
breakpoints while the DBG is armed. If BDM breakpoints are selected,
executing a TRACE1 instruction before the GO instruction is the
recommended way to avoid re-triggering a breakpoint if one does not wish
to de-arm the DBG. If SWI breakpoints are selected, disarming the DBG in
the SWI interrupt service routine is the recommended way to avoid
re-triggering a breakpoint.
16.5 Resets
The DBG module is disabled after reset.
The DBG module cannot cause a MCU reset.
16.6 Interrupts
The DBG contains one interrupt source. If a breakpoint is requested and BDM in DBGC2 is cleared, an
SWI interrupt will be generated.
Table 16-26. Breakpoint Setup
BEGIN TRGSEL DBGBRK Type of Debug Run
0 0 0 Fill trace buffer until trigger address
(no CPU breakpoint — keep running)
0 0 1 Fill trace buffer until trigger address, then a forced breakpoint
request occurs
0 1 0 Fill trace buffer until trigger opcode is about to execute
(no CPU breakpoint — keep running)
0 1 1 Fill trace buffer until trigger opcode about to execute, then a
tagged breakpoint request occurs
1 0 0 Start trace buffer at trigger address
(no CPU breakpoint — keep running)
1 0 1 Start trace buffer at trigger address, a forced breakpoint
request occurs when trace buffer is full
1 1 0 Start trace buffer at trigger opcode
(no CPU breakpoint — keep running)
1 1 1 Start tracebuffer attriggeropcode,aforcedbreakpointrequest
occurs when trace buffer is full
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 507
Chapter 17
Interrupt (INTV1) Block Description
17.1 Introduction
This section describes the functionality of the interrupt (INT) sub-block of the S12 core platform.
A block diagram of the interrupt sub-block is shown in Figure 17-1.
Figure 17-1. INTV1 Block Diagram
HPRIO (OPTIONAL)
INT
PRIORITY DECODER
VECTOR REQUEST
INTERRUPTS
RESET FLAGS
WRITE DATA BUS
HPRIO VECTOR
XMASK
IMASK
QUALIFIED
INTERRUPT INPUT REGISTERS
INTERRUPTS
AND CONTROL REGISTERS
HIGHEST PRIORITY
I-INTERRUPT
READ DATA BUS
WAKEUP
VECTOR ADDRESS
INTERRUPT PENDING
Chapter 17 Interrupt (INTV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
508 Freescale Semiconductor
The interrupt sub-block decodes the priority of all system exception requests and provides the applicable
vector for processing the exception. The INT supports I-bit maskable and X-bit maskable interrupts, a
non-maskable unimplemented opcode trap, a non-maskable software interrupt (SWI) or background debug
mode request, and three system reset vector requests. All interrupt related exception requests are managed
by the interrupt sub-block (INT).
17.1.1 Features
The INT includes these features:
Provides two to 122 I-bit maskable interrupt vectors (0xFF00–0xFFF2)
Provides one X-bit maskable interrupt vector (0xFFF4)
Provides a non-maskable software interrupt (SWI) or background debug mode request vector
(0xFFF6)
Provides a non-maskable unimplemented opcode trap (TRAP) vector (0xFFF8)
Provides three system reset vectors (0xFFFA–0xFFFE) (reset, CMR, and COP)
Determines the appropriate vector and drives it onto the address bus at the appropriate time
Signals the CPU that interrupts are pending
Provides control registers which allow testing of interrupts
Provides additional input signals which prevents requests for servicing I and X interrupts
Wakes the system from stop or wait mode when an appropriate interrupt occurs or whenever XIRQ
is active, even if XIRQ is masked
Provides asynchronous path for all I and X interrupts, (0xFF00–0xFFF4)
(Optional) selects and stores the highest priority I interrupt based on the value written into the
HPRIO register
17.1.2 Modes of Operation
The functionality of the INT sub-block in various modes of operation is discussed in the subsections that
follow.
Normal operation
The INT operates the same in all normal modes of operation.
Special operation
Interrupts may be tested in special modes through the use of the interrupt test registers.
Emulation modes
The INT operates the same in emulation modes as in normal modes.
Low power modes
See Section 17.4.1, “Low-Power Modes,” for details
Chapter 17 Interrupt (INTV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 509
17.2 External Signal Description
Most interfacing with the interrupt sub-block is done within the core. However, the interrupt does receive
direct input from the multiplexed external bus interface (MEBI) sub-block of the core for the IRQ and
XIRQ pin data.
17.3 Memory Map and Register Definition
Detailed descriptions of the registers and associated bits are given in the subsections that follow.
17.3.1 Module Memory Map
17.3.2 Register Descriptions
17.3.2.1 Interrupt Test Control Register
Read: See individual bit descriptions
Write: See individual bit descriptions
Table 17-1. INT Memory Map
Address
Offset Use Access
0x0015 Interrupt Test Control Register (ITCR) R/W
0x0016 Interrupt Test Registers (ITEST) R/W
0x001F Highest Priority Interrupt (Optional) (HPRIO) R/W
Module Base + 0x0015
Starting address location affected by INITRG register setting.
76543210
R000
WRTINT ADR3 ADR2 ADR1 ADR0
W
Reset 0 0 0 01111
= Unimplemented or Reserved
Figure 17-2. Interrupt Test Control Register (ITCR)
Chapter 17 Interrupt (INTV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
510 Freescale Semiconductor
17.3.2.2 Interrupt Test Registers
Read: Only in special modes. Reads will return either the state of the interrupt inputs of the interrupt
sub-block (WRTINT = 0) or the values written into the TEST registers (WRTINT = 1). Reads will always
return 0s in normal modes.
Write: Only in special modes and with WRTINT = 1 and CCR I mask = 1.
Table 17-2. ITCR Field Descriptions
Field Description
4
WRTINT Write to the Interrupt Test Registers
Read: anytime
Write: only in special modes and with I-bit mask and X-bit mask set.
0 Disables writes to the test registers; reads of the test registers will return the state of the interrupt inputs.
1 Disconnect the interrupt inputs from the priority decoder and use the values written into the ITEST registers
instead.
Note: Any interrupts which are pending at the time that WRTINT is set will remain until they are overwritten.
3:0
ADR[3:0] Test Register Select Bits
Read: anytime
Write: anytime
These bits determine which test register is selected on a read or write. The hexadecimal value written here will
be the same as the upper nibble of the lower byte of the vector selects. That is, an “F” written into ADR[3:0] will
select vectors 0xFFFE–0xFFF0 while a “7” written to ADR[3:0] will select vectors 0xFF7E–0xFF70.
Module Base + 0x0016
Starting address location affected by INITRG register setting.
76543210
RINTE INTC INTA INT8 INT6 INT4 INT2 INT0
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 17-3. Interrupt TEST Registers (ITEST)
Chapter 17 Interrupt (INTV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 511
17.3.2.3 Highest Priority I Interrupt (Optional)
Read: Anytime
Write: Only if I mask in CCR = 1
17.4 Functional Description
The interrupt sub-block processes all exception requests made by the CPU. These exceptions include
interrupt vector requests and reset vector requests. Each of these exception types and their overall priority
level is discussed in the subsections below.
Table 17-3. ITEST Field Descriptions
Field Description
7:0
INT[E:0] Interrupt TEST Bits — These registers are used in special modes for testing the interrupt logic and priority
independent of the system configuration. Each bit is used to force a specific interrupt vector by writing it to a
logic 1 state. Bits are named INTE through INT0 to indicate vectors 0xFFxE through 0xFFx0. These bits can be
written only in special modes and only with the WRTINT bit set (logic 1) in the interrupt test control register
(ITCR). In addition, I interrupts must be masked using the I bit in the CCR. In this state, the interrupt input lines
to the interrupt sub-block will be disconnected and interrupt requests will be generated only by this register.
These bits can also be read in special modes to view that an interrupt requested by a system block (such as a
peripheral block) has reached the INT module.
There is a test register implemented for every eight interrupts in the overall system. All of the test registers share
the same address and are individually selected using the value stored in the ADR[3:0] bits of the interrupt test
control register (ITCR).
Note: When ADR[3:0] have the value of 0x000F, only bits 2:0 in the ITEST register will be accessible. That is,
vectors higher than 0xFFF4 cannot be tested using the test registers and bits 7:3 will always read as a
logic 0. If ADR[3:0] point to an unimplemented test register, writes will have no effect and reads will always
return a logic 0 value.
Module Base + 0x001F
Starting address location affected by INITRG register setting.
76543210
RPSEL7 PSEL6 PSEL5 PSEL4 PSEL3 PSEL2 PSEL1 0
W
Reset 1 1 1 10010
= Unimplemented or Reserved
Figure 17-4. Highest Priority I Interrupt Register (HPRIO)
Table 17-4. HPRIO Field Descriptions
Field Description
7:1
PSEL[7:1] Highest Priority I Interrupt Select Bits The state of these bits determines which I-bit maskable interrupt will
bepromoted tohighest priority (of the I-bit maskableinterrupts). To promote an interrupt, the user writes the least
significant byte of the associated interrupt vector address to this register. If an unimplemented vector address or
a non I-bit masked vector address (value higher than 0x00F2) is written, IRQ (0xFFF2) will be the default highest
priority interrupt.
Chapter 17 Interrupt (INTV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
512 Freescale Semiconductor
17.4.1 Low-Power Modes
The INT does not contain any user-controlled options for reducing power consumption. The operation of
the INT in low-power modes is discussed in the following subsections.
17.4.1.1 Operation in Run Mode
The INT does not contain any options for reducing power in run mode.
17.4.1.2 Operation in Wait Mode
Clocks to the INT can be shut off during system wait mode and the asynchronous interrupt path will be
used to generate the wake-up signal upon recognition of a valid interrupt or any XIRQ request.
17.4.1.3 Operation in Stop Mode
Clocks to the INT can be shut off during system stop mode and the asynchronous interrupt path will be
used to generate the wake-up signal upon recognition of a valid interrupt or any XIRQ request.
17.5 Resets
The INT supports three system reset exception request types: normal system reset or power-on-reset
request, crystal monitor reset request, and COP watchdog reset request. The type of reset exception request
must be decoded by the system and the proper request made to the core. The INT will then provide the
service routine address for the type of reset requested.
17.6 Interrupts
As shown in the block diagram in Figure 17-1, the INT contains a register block to provide interrupt status
and control, an optional highest priority I interrupt (HPRIO) block, and a priority decoder to evaluate
whether pending interrupts are valid and assess their priority.
17.6.1 Interrupt Registers
The INT registers are accessible only in special modes of operation and function as described in
Section 17.3.2.1, “Interrupt Test Control Register,” and Section 17.3.2.2, “Interrupt Test Registers,”
previously.
17.6.2 Highest Priority I-Bit Maskable Interrupt
When the optional HPRIO block is implemented, the user is allowed to promote a single I-bit maskable
interrupt to be the highest priority I interrupt. The HPRIO evaluates all interrupt exception requests and
passes the HPRIO vector to the priority decoder if the highest priority I interrupt is active. RTI replaces
the promoted interrupt source.
Chapter 17 Interrupt (INTV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 513
17.6.3 Interrupt Priority Decoder
The priority decoder evaluates all interrupts pending and determines their validity and priority. When the
CPU requests an interrupt vector, the decoder will provide the vector for the highest priority interrupt
request. Because the vector is not supplied until the CPU requests it, it is possible that a higher priority
interrupt request could override the original exception that caused the CPU to request the vector. In this
case, the CPU will receive the highest priority vector and the system will process this exception instead of
the original request.
NOTE
Care must be taken to ensure that all exception requests remain active until
the system begins execution of the applicable service routine; otherwise, the
exception request may not be processed.
If for any reason the interrupt source is unknown (e.g., an interrupt request becomes inactive after the
interrupt has been recognized but prior to the vector request), the vector address will default to that of the
last valid interrupt that existed during the particular interrupt sequence. If the CPU requests an interrupt
vector when there has never been a pending interrupt request, the INT will provide the software interrupt
(SWI) vector address.
17.7 Exception Priority
The priority (from highest to lowest) and address of all exception vectors issued by the INT upon request
by the CPU is shown in Table 17-5.
Table 17-5. Exception Vector Map and Priority
Vector Address Source
0xFFFE–0xFFFF System reset
0xFFFC–0xFFFD Crystal monitor reset
0xFFFA–0xFFFB COP reset
0xFFF8–0xFFF9 Unimplemented opcode trap
0xFFF6–0xFFF7 Software interrupt instruction (SWI) or BDM vector request
0xFFF4–0xFFF5 XIRQ signal
0xFFF2–0xFFF3 IRQ signal
0xFFF0–0xFF00 Device-specific I-bit maskable interrupt sources (priority in descending order)
Chapter 17 Interrupt (INTV1) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
514 Freescale Semiconductor
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 515
Chapter 18
Multiplexed External Bus Interface (MEBIV3)
18.1 Introduction
This section describes the functionality of the multiplexed external bus interface (MEBI) sub-block of the
S12 core platform. The functionality of the module is closely coupled with the S12 CPU and the memory
map controller (MMC) sub-blocks.
Figure 18-1 is a block diagram of the MEBI. In Figure 18-1, the signals on the right hand side represent
pins that are accessible externally. On some chips, these may not all be bonded out.
The MEBI sub-block of the core serves to provide access and/or visibility to internal core data
manipulation operations including timing reference information at the external boundary of the core and/or
system. Depending upon the system operating mode and the state of bits within the control registers of the
MEBI, the internal 16-bit read and write data operations will be represented in 8-bit or 16-bit accesses
externally. Using control information from other blocks within the system, the MEBI will determine the
appropriate type of data access to be generated.
18.1.1 Features
The block name includes these distinctive features:
External bus controller with four 8-bit ports A,B, E, and K
Data and data direction registers for ports A, B, E, and K when used as general-purpose I/O
Control register to enable/disable alternate functions on ports E and K
Mode control register
Control register to enable/disable pull resistors on ports A, B, E, and K
Control register to enable/disable reduced output drive on ports A, B, E, and K
Control register to configure external clock behavior
Control register to configure IRQ pin operation
Logic to capture and synchronize external interrupt pin inputs
Chapter 18 Multiplexed External Bus Interface (MEBIV3)
MC9S12KG128 Data Sheet, Rev. 1.16
516 Freescale Semiconductor
Figure 18-1. MEBI Block Diagram
PE[7:2]/NOACC/
PE1/IRQ
PE0/XIRQ
BKGD/MODC/TAGHI
PK[7:0]/ECS/XCS/X[19:14]
PA[7:0]/A[15:8]/
D[15:8]/D[7:0]
Port KPort A
PB[7:0]/A[7:0]/
D[7:0]
Port BPort E
BKGD
REGS
EXT
BUS
I/F
CTL
Addr[19:0]
Data[15:0]
(Control)
Internal Bus
ECLK CTL
IRQ CTL
ADDR
ADDR
DATA
ADDR
DATA
PIPE CTL
CPU pipe info
IRQ interrupt
XIRQ interrupt
BDM tag info
IPIPE1/MODB/CLKTO
IPIPE0/MODA/
ECLK/
LSTRB/TAGLO
R/W
TAG CTL
Control signal(s)
Data signal (unidirectional)
Data bus (unidirectional)
Data bus (bidirectional)
Data signal (bidirectional)
mode
Chapter 18 Multiplexed External Bus Interface (MEBIV3)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 517
18.1.2 Modes of Operation
Normal expanded wide mode
Ports A and B are configured as a 16-bit multiplexed address and data bus and port E provides bus
control and status signals. This mode allows 16-bit external memory and peripheral devices to be
interfaced to the system.
Normal expanded narrow mode
Ports A and B are configured as a 16-bit address bus and port A is multiplexed with 8-bit data.
Port E provides bus control and status signals. This mode allows 8-bit external memory and
peripheral devices to be interfaced to the system.
Normal single-chip mode
There is no external expansion bus in this mode. The processor program is executed from internal
memory. Ports A, B, K, and most of E are available as general-purpose I/O.
Special single-chip mode
This mode is generally used for debugging single-chip operation, boot-strapping, or security
related operations. The active background mode is in control of CPU execution and BDM firmware
is waiting for additional serial commands through the BKGD pin. There is no external expansion
bus after reset in this mode.
Emulation expanded wide mode
Developers use this mode for emulation systems in which the users target application is normal
expanded wide mode.
Emulation expanded narrow mode
Developers use this mode for emulation systems in which the users target application is normal
expanded narrow mode.
Special test mode
Ports A and B are configured as a 16-bit multiplexed address and data bus and port E provides bus
control and status signals. In special test mode, the write protection of many control bits is lifted
so that they can be thoroughly tested without needing to go through reset.
Special peripheral mode
This mode is intended for Freescale Semiconductor factory testing of the system. The CPU is
inactive and an external (tester) bus master drives address, data, and bus control signals.
18.2 External Signal Description
In typical implementations, the MEBI sub-block of the core interfaces directly with external system pins.
Some pins may not be bonded out in all implementations.
Table 18-1 outlines the pin names and functions and gives a brief description of their operation reset state
of these pins and associated pull-ups or pull-downs is dependent on the mode of operation and on the
integration of this block at the chip level (chip dependent).
Chapter 18 Multiplexed External Bus Interface (MEBIV3)
MC9S12KG128 Data Sheet, Rev. 1.16
518 Freescale Semiconductor
.Table 18-1. External System Pins Associated With MEBI
Pin Name Pin Functions Description
BKGD/MODC/
TAGHI MODC At the rising edge on RESET, the state of this pin is registered into the MODC
bit to set the mode. (This pin always has an internal pullup.)
BKGD Pseudo open-drain communication pin for the single-wire background debug
mode. There is an internal pull-up resistor on this pin.
TAGHI When instruction tagging is on, a 0 at the falling edge of E tags the high half of
the instruction word being read into the instruction queue.
PA7/A15/D15/D7
thru
PA0/A8/D8/D0
PA7–PA0 General-purpose I/O pins, see PORTA and DDRA registers.
A15–A8 High-order address lines multiplexed during ECLK low. Outputs except in
special peripheral mode where they are inputs from an external tester system.
D15–D8 High-order bidirectional data lines multiplexed during ECLK high in expanded
wide modes, special peripheral mode, and visible internal accesses (IVIS = 1)
in emulation expanded narrow mode. Direction of data transfer is generally
indicated by R/W.
D15/D7
thru
D8/D0
Alternate high-order and low-order bytes of the bidirectional data lines
multiplexedduring ECLKhighinexpandednarrowmodes andnarrowaccesses
in wide modes. Direction of data transfer is generally indicated by R/W.
PB7/A7/D7
thru
PB0/A0/D0
PB7–PB0 General-purpose I/O pins, see PORTB and DDRB registers.
A7–A0 Low-order address lines multiplexed during ECLK low. Outputs except in
special peripheral mode where they are inputs from an external tester system.
D7–D0 Low-order bidirectional data lines multiplexed during ECLK high in expanded
wide modes, special peripheral mode, and visible internal accesses (with
IVIS = 1) in emulation expanded narrow mode. Direction of data transfer is
generally indicated by R/W.
PE7/NOACC PE7 General-purpose I/O pin, see PORTE and DDRE registers.
NOACC CPU No Accessoutput.Indicates whether the currentcycle is a freecycle.Only
available in expanded modes.
PE6/IPIPE1/
MODB/CLKTO MODB At the rising edge of RESET, the state of this pin is registered into the MODB
bit to set the mode.
PE6 General-purpose I/O pin, see PORTE and DDRE registers.
IPIPE1 Instruction pipe status bit 1, enabled by PIPOE bit in PEAR.
CLKTO System clock testoutput. Only available in special modes. PIPOE = 1 overrides
this function. The enable for this function is in the clock module.
PE5/IPIPE0/MODA MODA At the rising edge on RESET, the state of this pin is registered into the MODA
bit to set the mode.
PE5 General-purpose I/O pin, see PORTE and DDRE registers.
IPIPE0 Instruction pipe status bit 0, enabled by PIPOE bit in PEAR.
Chapter 18 Multiplexed External Bus Interface (MEBIV3)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 519
Detailed descriptions of these pins can be found in the device overview chapter.
18.3 Memory Map and Register Definition
A summary of the registers associated with the MEBI sub-block is shown in Table 18-2. Detailed
descriptions of the registers and bits are given in the subsections that follow. On most chips the registers
are mappable. Therefore, the upper bits may not be all 0s as shown in the table and descriptions.
PE4/ECLK PE4 General-purpose I/O pin, see PORTE and DDRE registers.
ECLK Bus timing reference clock, can operate as a free-running clock at the system
clock rate or to produce one low-high clock per visible access, with the high
period stretched for slow accesses. ECLK is controlled by the NECLK bit in
PEAR, the IVIS bit in MODE, and the ESTR bit in EBICTL.
PE3/LSTRB/ TAGLO PE3 General-purpose I/O pin, see PORTE and DDRE registers.
LSTRB Low strobe bar, 0 indicates valid data on D7–D0.
SZ8 In special peripheral mode, this pin is an input indicating the size of the data
transfer (0 = 16-bit; 1 = 8-bit).
TAGLO In expanded wide mode or emulation narrow modes, when instruction tagging
is on and low strobe is enabled, a 0 at the falling edge of E tags the low half of
the instruction word being read into the instruction queue.
PE2/R/W PE2 General-purpose I/O pin, see PORTE and DDRE registers.
R/W Read/write, indicates the direction of internal data transfers. This is an output
except in special peripheral mode where it is an input.
PE1/IRQ PE1 General-purpose input-only pin, can be read even if IRQ enabled.
IRQ Maskable interrupt request, can be level sensitive or edge sensitive.
PE0/XIRQ PE0 General-purpose input-only pin.
XIRQ Non-maskable interrupt input.
PK7/ECS PK7 General-purpose I/O pin, see PORTK and DDRK registers.
ECS Emulation chip select
PK6/XCS PK6 General-purpose I/O pin, see PORTK and DDRK registers.
XCS External data chip select
PK5/X19
thru
PK0/X14
PK5–PK0 General-purpose I/O pins, see PORTK and DDRK registers.
X19–X14 Memory expansion addresses
Table 18-1. External System Pins Associated With MEBI (continued)
Pin Name Pin Functions Description
Chapter 18 Multiplexed External Bus Interface (MEBIV3)
MC9S12KG128 Data Sheet, Rev. 1.16
520 Freescale Semiconductor
18.3.1 Module Memory Map
18.3.2 Register Descriptions
18.3.2.1 Port A Data Register (PORTA)
Table 18-2. MEBI Memory Map
Address
Offset Use Access
0x0000 Port A Data Register (PORTA) R/W
0x0001 Port B Data Register (PORTB) R/W
0x0002 Data Direction Register A (DDRA) R/W
0x0003 Data Direction Register B (DDRB) R/W
0x0004 Reserved R
0x0005 Reserved R
0x0006 Reserved R
0x0007 Reserved R
0x0008 Port E Data Register (PORTE) R/W
0x0009 Data Direction Register E (DDRE) R/W
0x000A Port E Assignment Register (PEAR) R/W
0x000B Mode Register (MODE) R/W
0x000C Pull Control Register (PUCR) R/W
0x000D Reduced Drive Register (RDRIV) R/W
0x000E External Bus Interface Control Register (EBICTL) R/W
0x000F Reserved R
0x001E IRQ Control Register (IRQCR) R/W
0x00032 Port K Data Register (PORTK) R/W
0x00033 Data Direction Register K (DDRK) R/W
Module Base + 0x0000
Starting address location affected by INITRG register setting.
76543210
RBit 7 6 5 4 3 2 1 Bit 0
W
Reset 0 0 0 0 0 0 0 0
Single Chip PA7 PA6 PA5 PA4 PA3 PA2 PA1 PA0
Expanded Wide,
Emulation Narrow with
IVIS, and Peripheral AB/DB15 AB/DB14 AB/DB13 AB/DB12 AB/DB11 AB/DB10 AB/DB9 AB/DB8
Expanded Narrow AB15 and
DB15/DB7 AB14 and
DB14/DB6 AB13 and
DB13/DB5 AB12 and
DB12/DB4 AB11 and
DB11/DB3 AB10 and
DB10/DB2 AB9 and
DB9/DB1 AB8 and
DB8/DB0
Figure 18-2. Port A Data Register (PORTA)
Chapter 18 Multiplexed External Bus Interface (MEBIV3)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 521
Read: Anytime when register is in the map
Write: Anytime when register is in the map
Port A bits 7 through 0 are associated with address lines A15 through A8 respectively and data lines
D15/D7 through D8/D0 respectively. When this port is not used for external addresses such as in
single-chip mode, these pins can be used as general-purpose I/O. Data direction register A (DDRA)
determines the primary direction of each pin. DDRA also determines the source of data for a read of
PORTA.
This register is not in the on-chip memory map in expanded and special peripheral modes. Therefore, these
accesses will be echoed externally.
NOTE
To ensure that you read the value present on the PORTA pins, always wait
at least one cycle after writing to the DDRA register before reading from the
PORTA register.
18.3.2.2 Port B Data Register (PORTB)
Read: Anytime when register is in the map
Write: Anytime when register is in the map
Port B bits 7 through 0 are associated with address lines A7 through A0 respectively and data lines D7
through D0 respectively. When this port is not used for external addresses, such as in single-chip mode,
these pins can be used as general-purpose I/O. Data direction register B (DDRB) determines the primary
direction of each pin. DDRB also determines the source of data for a read of PORTB.
This register is not in the on-chip memory map in expanded and special peripheral modes. Therefore, these
accesses will be echoed externally.
Module Base + 0x0001
Starting address location affected by INITRG register setting.
76543210
RBit 7 6 5 4 3 2 1 Bit 0
W
Reset 0 0 0 0 0 0 0 0
Single Chip PB7 PB6 PB5 PB4 PB3 PB2 PB1 PB0
Expanded Wide,
Emulation Narrow with
IVIS, and Peripheral AB/DB7 AB/DB6 AB/DB5 AB/DB4 AB/DB3 AB/DB2 AB/DB1 AB/DB0
Expanded Narrow AB7 AB6 AB5 AB4 AB3 AB2 AB1 AB0
Figure 18-3. Port A Data Register (PORTB)
Chapter 18 Multiplexed External Bus Interface (MEBIV3)
MC9S12KG128 Data Sheet, Rev. 1.16
522 Freescale Semiconductor
NOTE
To ensure that you read the value present on the PORTB pins, always wait
at least one cycle after writing to the DDRB register before reading from the
PORTB register.
Chapter 18 Multiplexed External Bus Interface (MEBIV3)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 523
18.3.2.3 Data Direction Register A (DDRA)
Read: Anytime when register is in the map
Write: Anytime when register is in the map
This register controls the data direction for port A. When port A is operating as a general-purpose I/O port,
DDRA determines the primary direction for each port A pin. A 1 causes the associated port pin to be an
output and a 0 causes the associated pin to be a high-impedance input. The value in a DDR bit also affects
the source of data for reads of the corresponding PORTA register. If the DDR bit is 0 (input) the buffered
pin input state is read. If the DDR bit is 1 (output) the associated port data register bit state is read.
This register is not in the on-chip memory map in expanded and special peripheral modes. Therefore, these
accesses will be echoed externally. It is reset to 0x00 so the DDR does not override the three-state control
signals.
Module Base + 0x0002
Starting address location affected by INITRG register setting.
76543210
RBit 7 6 5 4321Bit 0
W
Reset 0 0 0 00000
Figure 18-4. Data Direction Register A (DDRA)
Table 18-3. DDRA Field Descriptions
Field Description
7:0
DDRA Data Direction Port A
0 Configure the corresponding I/O pin as an input
1 Configure the corresponding I/O pin as an output
Chapter 18 Multiplexed External Bus Interface (MEBIV3)
MC9S12KG128 Data Sheet, Rev. 1.16
524 Freescale Semiconductor
18.3.2.4 Data Direction Register B (DDRB)
Read: Anytime when register is in the map
Write: Anytime when register is in the map
This register controls the data direction for port B. When port B is operating as a general-purpose I/O port,
DDRB determines the primary direction for each port B pin. A 1 causes the associated port pin to be an
output and a 0 causes the associated pin to be a high-impedance input. The value in a DDR bit also affects
the source of data for reads of the corresponding PORTB register. If the DDR bit is 0 (input) the buffered
pin input state is read. If the DDR bit is 1 (output) the associated port data register bit state is read.
This register is not in the on-chip memory map in expanded and special peripheral modes. Therefore, these
accesses will be echoed externally. It is reset to 0x00 so the DDR does not override the three-state control
signals.
Module Base + 0x0003
Starting address location affected by INITRG register setting.
76543210
RBit 7 6 5 4321Bit 0
W
Reset 0 0 0 00000
Figure 18-5. Data Direction Register B (DDRB)
Table 18-4. DDRB Field Descriptions
Field Description
7:0
DDRB Data Direction Port B
0 Configure the corresponding I/O pin as an input
1 Configure the corresponding I/O pin as an output
Chapter 18 Multiplexed External Bus Interface (MEBIV3)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 525
18.3.2.5 Reserved Registers
Module Base + 0x0004
Starting address location affected by INITRG register setting.
76543210
R00000000
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 18-6. Reserved Register
Module Base + 0x0005
Starting address location affected by INITRG register setting.
76543210
R00000000
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 18-7. Reserved Register
Module Base + 0x0006
Starting address location affected by INITRG register setting.
76543210
R00000000
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 18-8. Reserved Register
Module Base + 0x0007
Starting address location affected by INITRG register setting.
76543210
R00000000
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 18-9. Reserved Register
Chapter 18 Multiplexed External Bus Interface (MEBIV3)
MC9S12KG128 Data Sheet, Rev. 1.16
526 Freescale Semiconductor
These register locations are not used (reserved). All unused registers and bits in this block return logic 0s
when read. Writes to these registers have no effect.
These registers are not in the on-chip map in special peripheral mode.
18.3.2.6 Port E Data Register (PORTE)
Read: Anytime when register is in the map
Write: Anytime when register is in the map
Port E is associated with external bus control signals and interrupt inputs. These include mode select
(MODB/IPIPE1, MODA/IPIPE0), E clock, size (LSTRB/TAGLO), read/write (R/W), IRQ, and XIRQ.
When not used for one of these specific functions, port E pins 7:2 can be used as general-purpose I/O and
pins 1:0 can be used as general-purpose input. The port E assignment register (PEAR) selects the function
of each pin and DDRE determines whether each pin is an input or output when it is configured to be
general-purpose I/O. DDRE also determines the source of data for a read of PORTE.
Some of these pins have software selectable pull resistors. IRQ and XIRQ can only be pulled up whereas
the polarity of the PE7, PE4, PE3, and PE2 pull resistors are determined by chip integration. Please refer
to the device overview chapter (Signal Property Summary) to determine the polarity of these resistors.
A single control bit enables the pull devices for all of these pins when they are configured as inputs.
This register is not in the on-chip map in special peripheral mode or in expanded modes when the EME
bit is set. Therefore, these accesses will be echoed externally.
NOTE
It is unwise to write PORTE and DDRE as a word access. If you are
changing port E pins from being inputs to outputs, the data may have extra
transitions during the write. It is best to initialize PORTE before enabling as
outputs.
Module Base + 0x0008
Starting address location affected by INITRG register setting.
76543210
RBit 7 65432
Bit 1 Bit 0
W
Reset 000000uu
Alternate
Pin Function NOACC MODB
or IPIPE1
or CLKTO
MODA
or IPIPE0 ECLK LSTRB
or TAGLO R/W IRQ XIRQ
= Unimplemented or Reserved u = Unaffected by reset
Figure 18-10. Port E Data Register (PORTE)
Chapter 18 Multiplexed External Bus Interface (MEBIV3)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 527
NOTE
To ensure that you read the value present on the PORTE pins, always wait
at least one cycle after writing to the DDRE register before reading from the
PORTE register.
18.3.2.7 Data Direction Register E (DDRE)
Read: Anytime when register is in the map
Write: Anytime when register is in the map
Data direction register E is associated with port E. For bits in port E that are configured as general-purpose
I/O lines, DDRE determines the primary direction of each of these pins. A 1 causes the associated bit to
be an output and a 0 causes the associated bit to be an input. Port E bit 1 (associated with IRQ) and bit 0
(associated with XIRQ) cannot be configured as outputs. Port E, bits 1 and 0, can be read regardless of
whether the alternate interrupt function is enabled. The value in a DDR bit also affects the source of data
for reads of the corresponding PORTE register. If the DDR bit is 0 (input) the buffered pin input state is
read. If the DDR bit is 1 (output) the associated port data register bit state is read.
This register is not in the on-chip memory map in expanded and special peripheral modes. Therefore, these
accesses will be echoed externally. Also, it is not in the map in expanded modes while the EME control bit
is set.
Module Base + 0x0009
Starting address location affected by INITRG register setting.
76543210
RBit 7 6 5 4 3 Bit 2 00
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 18-11. Data Direction Register E (DDRE)
Table 18-5. DDRE Field Descriptions
Field Description
7:2
DDRE Data Direction Port E
0 Configure the corresponding I/O pin as an input
1 Configure the corresponding I/O pin as an output
Note: It is unwise to write PORTE and DDRE as a word access. If you are changing port E pins from inputs to
outputs, the data may have extra transitions during the write. It is best to initialize PORTE before enabling
as outputs.
Chapter 18 Multiplexed External Bus Interface (MEBIV3)
MC9S12KG128 Data Sheet, Rev. 1.16
528 Freescale Semiconductor
18.3.2.8 Port E Assignment Register (PEAR)
Read: Anytime (provided this register is in the map).
Write: Each bit has specific write conditions. Please refer to the descriptions of each bit on the following
pages.
Port E serves as general-purpose I/O or as system and bus control signals. The PEAR register is used to
choose between the general-purpose I/O function and the alternate control functions. When an alternate
control function is selected, the associated DDRE bits are overridden.
The reset condition of this register depends on the mode of operation because bus control signals are
needed immediately after reset in some modes. In normal single-chip mode, no external bus control signals
are needed so all of port E is configured for general-purpose I/O. In normal expanded modes, only the E
clock is configured for its alternate bus control function and the other bits of port E are configured for
general-purpose I/O. As the reset vector is located in external memory, the E clock is required for this
access. R/W is only needed by the system when there are external writable resources. If the normal
expanded system needs any other bus control signals, PEAR would need to be written before any access
that needed the additional signals. In special test and emulation modes, IPIPE1, IPIPE0, E, LSTRB, and
R/W are configured out of reset as bus control signals.
This register is not in the on-chip memory map in expanded and special peripheral modes. Therefore, these
accesses will be echoed externally.
Module Base + 0x000A
Starting address location affected by INITRG register setting.
76543210
RNOACCE 0PIPOE NECLK LSTRE RDWE 00
W
Reset
Special Single Chip 0 0 0 0 0 0 0 0
Special Test 0 0 1 0 1 1 0 0
Peripheral 0 0 0 0 0 0 0 0
Emulation Expanded
Narrow 10101100
Emulation Expanded
Wide 10101100
Normal Single Chip 0 0 0 1 0 0 0 0
Normal Expanded
Narrow 00000000
Normal Expanded Wide 0 0 0 0 0 0 0 0
= Unimplemented or Reserved
Figure 18-12. Port E Assignment Register (PEAR)
Chapter 18 Multiplexed External Bus Interface (MEBIV3)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 529
Table 18-6. PEAR Field Descriptions
Field Description
7
NOACCE CPU No Access Output Enable
Normal: write once
Emulation: write never
Special: write anytime
1 The associated pin (port E, bit 7) is general-purpose I/O.
0 The associated pin (port E, bit 7) is output and indicates whether the cycle is a CPU free cycle.
This bit has no effect in single-chip or special peripheral modes.
5
PIPOE Pipe Status Signal Output Enable
Normal: write once
Emulation: write never
Special: write anytime.
0 The associated pins (port E, bits 6:5) are general-purpose I/O.
1 The associated pins (port E, bits 6:5) are outputs and indicate the state of the instruction queue
This bit has no effect in single-chip or special peripheral modes.
4
NECLK No External E Clock
Normal and special: write anytime
Emulation: write never
0 The associated pin (port E, bit 4) is the external E clock pin. External E clock is free-running if ESTR = 0
1 The associated pin (port E, bit 4) is a general-purpose I/O pin.
External E clock is available as an output in all modes.
3
LSTRE Low Strobe (LSTRB) Enable
Normal: write once
Emulation: write never
Special: write anytime.
0 The associated pin (port E, bit 3) is a general-purpose I/O pin.
1 The associated pin (port E, bit 3) is configured as the LSTRB bus control output. If BDM tagging is enabled,
TAGLO is multiplexed in on the rising edge of ECLK and LSTRB is driven out on the falling edge of ECLK.
This bit has no effect in single-chip, peripheral, or normal expanded narrow modes.
Note: LSTRB is used during external writes. After reset in normal expanded mode, LSTRB is disabled to provide
an extra I/O pin. If LSTRB is needed, it should be enabled before any external writes. External reads do
not normally need LSTRB because all 16 data bits can be driven even if the system only needs 8 bits of
data.
2
RDWE Read/Write Enable
Normal: write once
Emulation: write never
Special: write anytime
0 The associated pin (port E, bit 2) is a general-purpose I/O pin.
1 The associated pin (port E, bit 2) is configured as the R/W pin
This bit has no effect in single-chip or special peripheral modes.
Note: R/W is used for external writes. After reset in normal expanded mode, R/W is disabled to provide an extra
I/O pin. If R/W is needed it should be enabled before any external writes.
Chapter 18 Multiplexed External Bus Interface (MEBIV3)
MC9S12KG128 Data Sheet, Rev. 1.16
530 Freescale Semiconductor
18.3.2.9 Mode Register (MODE)
Read: Anytime (provided this register is in the map).
Write: Each bit has specific write conditions. Please refer to the descriptions of each bit on the following
pages.
The MODE register is used to establish the operating mode and other miscellaneous functions (i.e.,
internal visibility and emulation of port E and K).
In special peripheral mode, this register is not accessible but it is reset as shown to system configuration
features. Changes to bits in the MODE register are delayed one cycle after the write.
This register is not in the on-chip memory map in expanded and special peripheral modes. Therefore, these
accesses will be echoed externally.
Module Base + 0x000B
Starting address location affected by INITRG register setting.
76543210
RMODC MODB MODA 0IVIS 0EMK EME
W
Reset
Special Single Chip 0 0 0 0 0 0 0 0
Emulation Expanded
Narrow 00101011
Special Test 0 1 0 0 1 0 0 0
Emulation Expanded
Wide 01101011
Normal Single Chip 1 0 0 0 0 0 0 0
Normal Expanded
Narrow 10100000
Peripheral 1 1 0 0 0 0 0 0
Normal Expanded Wide 1 1 1 0 0 0 0 0
= Unimplemented or Reserved
Figure 18-13. Mode Register (MODE)
Chapter 18 Multiplexed External Bus Interface (MEBIV3)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 531
Table 18-7. MODE Field Descriptions
Field Description
7:5
MOD[C:A] Mode Select Bits — These bits indicate the current operating mode.
If MODA = 1, then MODC, MODB, and MODA are write never.
If MODC = MODA = 0, then MODC, MODB, and MODA are writable with the exception that you cannot change
to or from special peripheral mode
If MODC = 1, MODB = 0, and MODA = 0, then MODC is write never. MODB and MODA are write once, except
that you cannot change to special peripheral mode. From normal single-chip, only normal expanded narrow and
normal expanded wide modes are available.
See Table 18-8 and Table 18-16.
3
IVIS Internal Visibility (for both read and write accesses) — This bit determines whether internal accesses
generate a bus cycle that is visible on the external bus.
Normal: write once
Emulation: write never
Special: write anytime
0 No visibility of internal bus operations on external bus.
1 Internal bus operations are visible on external bus.
1
EMK Emulate Port K
Normal: write once
Emulation: write never
Special: write anytime
0 PORTK and DDRK are in the memory map so port K can be used for general-purpose I/O.
1 If in any expanded mode, PORTK and DDRK are removed from the memory map.
In single-chip modes, PORTK and DDRK are always in the map regardless of the state of this bit.
In special peripheral mode, PORTK and DDRK are never in the map regardless of the state of this bit.
0
EME Emulate Port E
Normal and Emulation: write never
Special: write anytime
0 PORTE and DDRE are in the memory map so port E can be used for general-purpose I/O.
1 If in any expanded mode or special peripheral mode, PORTE and DDRE are removed from the memory map.
Removing the registers from the map allows the user to emulate the function of these registers externally.
In single-chip modes, PORTE and DDRE are always in the map regardless of the state of this bit.
Chapter 18 Multiplexed External Bus Interface (MEBIV3)
MC9S12KG128 Data Sheet, Rev. 1.16
532 Freescale Semiconductor
18.3.2.10 Pull Control Register (PUCR)
Read: Anytime (provided this register is in the map).
Write: Anytime (provided this register is in the map).
This register is used to select pull resistors for the pins associated with the core ports. Pull resistors are
assigned on a per-port basis and apply to any pin in the corresponding port that is currently configured as
an input. The polarity of these pull resistors is determined by chip integration. Please refer to the device
overview chapter to determine the polarity of these resistors.
Table 18-8. MODC, MODB, and MODA Write Capability1
1No writes to the MOD bits are allowed while operating in a secure mode. For more details, refer to the device
overview chapter.
MODC MODB MODA Mode MODx Write Capability
0 0 0 Special single chip MODC, MODB, and MODA
write anytime but not to 1102
2If you are in a special single-chip or special test mode and you write to this register, changing to normal sin-
gle-chip mode, then one allowed write to this register remains. If you write to normal expanded or emulation
mode, then no writes remain.
0 0 1 Emulation narrow No write
0 1 0 Special test MODC, MODB, and MODA
write anytime but not to 110(2)
0 1 1 Emulation wide No write
1 0 0 Normal single chip MODC write never,
MODB and MODA write once
but not to 110
1 0 1 Normal expanded narrow No write
1 1 0 Special peripheral No write
1 1 1 Normal expanded wide No write
Module Base + 0x000C
Starting address location affected by INITRG register setting.
76543210
RPUPKE 00
PUPEE 00
PUPBE PUPAE
W
Reset110010000
NOTES:
1. The default value of this parameter is shown. Please refer to the device overview chapter to deter-
mine the actual reset state of this register.
= Unimplemented or Reserved
Figure 18-14. Pull Control Register (PUCR)
Chapter 18 Multiplexed External Bus Interface (MEBIV3)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 533
This register is not in the on-chip memory map in expanded and special peripheral modes. Therefore, these
accesses will be echoed externally.
NOTE
These bits have no effect when the associated pin(s) are outputs. (The pull
resistors are inactive.)
18.3.2.11 Reduced Drive Register (RDRIV)
Read: Anytime (provided this register is in the map)
Write: Anytime (provided this register is in the map)
This register is used to select reduced drive for the pins associated with the core ports. This gives reduced
power consumption and reduced RFI with a slight increase in transition time (depending on loading). This
feature would be used on ports which have a light loading. The reduced drive function is independent of
which function is being used on a particular port.
This register is not in the on-chip memory map in expanded and special peripheral modes. Therefore, these
accesses will be echoed externally.
Table 18-9. PUCR Field Descriptions
Field Description
7
PUPKE Pull resistors Port K Enable
0 Port K pull resistors are disabled.
1 Enable pull resistors for port K input pins.
4
PUPEE Pull resistors Port E Enable
0 Port E pull resistors on bits 7, 4:0 are disabled.
1 Enable pull resistors for port E input pins bits 7, 4:0.
Note: Pins 5 and 6 of port E have pull resistors which are only enabled during reset. This bit has no effect on
these pins.
1
PUPBE Pull resistors Port B Enable
0 Port B pull resistors are disabled.
1 Enable pull resistors for all port B input pins.
0
PUPAE Pull resistors Port A Enable
0 Port A pull resistors are disabled.
1 Enable pull resistors for all port A input pins.
Module Base + 0x000D
Starting address location affected by INITRG register setting.
76543210
RRDRK 00
RDPE 00
RDPB RDPA
W
Reset 00000000
= Unimplemented or Reserved
Figure 18-15. Reduced Drive Register (RDRIV)
Chapter 18 Multiplexed External Bus Interface (MEBIV3)
MC9S12KG128 Data Sheet, Rev. 1.16
534 Freescale Semiconductor
18.3.2.12 External Bus Interface Control Register (EBICTL)
Read: Anytime (provided this register is in the map)
Write: Refer to individual bit descriptions below
The EBICTL register is used to control miscellaneous functions (i.e., stretching of external E clock).
This register is not in the on-chip memory map in expanded and special peripheral modes. Therefore, these
accesses will be echoed externally.
Table 18-10. RDRIV Field Descriptions
Field Description
7
RDRK Reduced Drive of Port K
0 All port K output pins have full drive enabled.
1 All port K output pins have reduced drive enabled.
4
RDPE Reduced Drive of Port E
0 All port E output pins have full drive enabled.
1 All port E output pins have reduced drive enabled.
1
RDPB Reduced Drive of Port B
0 All port B output pins have full drive enabled.
1 All port B output pins have reduced drive enabled.
0
RDPA Reduced Drive of Ports A
0 All port A output pins have full drive enabled.
1 All port A output pins have reduced drive enabled.
Module Base + 0x000E
Starting address location affected by INITRG register setting.
76543210
R0000000
ESTR
W
Reset:
Peripheral
All other modes 0
00
00
00
00
00
00
00
1
= Unimplemented or Reserved
Figure 18-16. External Bus Interface Control Register (EBICTL)
Table 18-11. EBICTL Field Descriptions
Field Description
0
ESTR E Clock Stretches This control bit determines whether the E clock behaves as a simple free-running clock or
as a bus control signal that is active only for external bus cycles.
Normal and Emulation: write once
Special: write anytime
0 E never stretches (always free running).
1 E stretches high during stretched external accesses and remains low during non-visible internal accesses.
This bit has no effect in single-chip modes.
Chapter 18 Multiplexed External Bus Interface (MEBIV3)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 535
18.3.2.13 Reserved Register
This register location is not used (reserved). All bits in this register return logic 0s when read. Writes to
this register have no effect.
This register is not in the on-chip memory map in expanded and special peripheral modes. Therefore, these
accesses will be echoed externally.
18.3.2.14 IRQ Control Register (IRQCR)
Read: See individual bit descriptions below
Write: See individual bit descriptions below
Module Base + 0x000F
Starting address location affected by INITRG register setting.
76543210
R00000000
W
Reset 00000000
= Unimplemented or Reserved
Figure 18-17. Reserved Register
Module Base + 0x001E
Starting address location affected by INITRG register setting.
76543210
RIRQE IRQEN 000000
W
Reset 01000000
= Unimplemented or Reserved
Figure 18-18. IRQ Control Register (IRQCR)
Table 18-12. IRQCR Field Descriptions
Field Description
7
IRQE IRQ Select Edge Sensitive Only
Special modes: read or write anytime
Normal and Emulation modes: read anytime, write once
0 IRQ configured for low level recognition.
1 IRQ configured to respond only to falling edges. Falling edges on the IRQ pin will be detected anytime
IRQE = 1 and will be cleared only upon a reset or the servicing of the IRQ interrupt.
6
IRQEN External IRQ Enable
Normal, emulation, and special modes: read or write anytime
0 External IRQ pin is disconnected from interrupt logic.
1 External IRQ pin is connected to interrupt logic.
Note: When IRQEN = 0, the edge detect latch is disabled.
Chapter 18 Multiplexed External Bus Interface (MEBIV3)
MC9S12KG128 Data Sheet, Rev. 1.16
536 Freescale Semiconductor
18.3.2.15 Port K Data Register (PORTK)
Read: Anytime
Write: Anytime
This port is associated with the internal memory expansion emulation pins. When the port is not enabled
to emulate the internal memory expansion, the port pins are used as general-purpose I/O. When port K is
operating as a general-purpose I/O port, DDRK determines the primary direction for each port K pin. A 1
causes the associated port pin to be an output and a 0 causes the associated pin to be a high-impedance
input. The value in a DDR bit also affects the source of data for reads of the corresponding PORTK register.
If the DDR bit is 0 (input) the buffered pin input is read. If the DDR bit is 1 (output) the output of the port
data register is read.
This register is not in the map in peripheral or expanded modes while the EMK control bit in MODE
register is set. Therefore, these accesses will be echoed externally.
When inputs, these pins can be selected to be high impedance or pulled up, based upon the state of the
PUPKE bit in the PUCR register.
Module Base + 0x0032
Starting address location affected by INITRG register setting.
76543210
RBit 7 654321Bit 0
W
Reset 00000000
Alternate
Pin Function ECS XCS XAB19 XAB18 XAB17 XAB16 XAB15 XAB14
Figure 18-19. Port K Data Register (PORTK)
Table 18-13. PORTK Field Descriptions
Field Description
7
Port K, Bit 7 Port K, Bit 7 — This bit is used as an emulation chip select signal for the emulation of the internal memory
expansion, or as general-purpose I/O, depending upon the state of the EMK bit in the MODE register. While
this bit is used as a chip select, the external bit will return to its de-asserted state (VDD) for approximately 1/4
cycle just after the negative edge of ECLK, unless the external access is stretched and ECLK is free-running
(ESTR bit in EBICTL = 0). See the MMC block description chapter for additional details on when this signal
will be active.
6
Port K, Bit 6 Port K, Bit 6 — This bit is used as an external chip select signal for most external accesses that are not
selected by ECS (see the MMC block description chapter for more details), depending upon the state the of
the EMK bit in the MODE register. While this bit is used as a chip select, the external pin will return to its de-
asserted state (VDD) for approximately 1/4 cycle just after the negative edge of ECLK, unless the external
access is stretched and ECLK is free-running (ESTR bit in EBICTL = 0).
5:0
Port K, Bits 5:0 Port K, Bits 5:0 These six bits are used to determine which FLASH/ROM or external memory array page
is being accessed. They can be viewed as expanded addresses XAB19–XAB14 of the 20-bit address used to
access up to1M byte internal FLASH/ROM or external memory array. Alternatively, these bits can be used for
general-purpose I/O depending upon the state of the EMK bit in the MODE register.
Chapter 18 Multiplexed External Bus Interface (MEBIV3)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 537
18.3.2.16 Port K Data Direction Register (DDRK)
Read: Anytime
Write: Anytime
This register determines the primary direction for each port K pin configured as general-purpose I/O. This
register is not in the map in peripheral or expanded modes while the EMK control bit in MODE register is
set. Therefore, these accesses will be echoed externally.
18.4 Functional Description
18.4.1 Detecting Access Type from External Signals
The external signals LSTRB, R/W, and AB0 indicate the type of bus access that is taking place. Accesses
to the internal RAM module are the only type of access that would produce LSTRB = AB0 = 1, because
the internal RAM is specifically designed to allow misaligned 16-bit accesses in a single cycle. In these
cases the data for the address that was accessed is on the low half of the data bus and the data for
address + 1 is on the high half of the data bus. This is summarized in Table 18-15.
Module Base + 0x0033
Starting address location affected by INITRG register setting.
76543210
RBit 7 654321Bit 0
W
Reset 00000000
Figure 18-20. Port K Data Direction Register (DDRK)
Table 18-14. EBICTL Field Descriptions
Field Description
7:0
DDRK Data Direction Port K Bits
0 Associated pin is a high-impedance input
1 Associated pin is an output
Note: It is unwise to write PORTK and DDRK as a word access. If you are changing port K pins from inputs to
outputs, the data may have extra transitions during the write. It is best to initialize PORTK before enabling
as outputs.
Note: To ensure that you read the correct value from the PORTK pins, always wait at least one cycle after writing
to the DDRK register before reading from the PORTK register.
Table 18-15. Access Type vs. Bus Control Pins
LSTRB AB0 R/W Type of Access
1 0 1 8-bit read of an even address
0 1 1 8-bit read of an odd address
1 0 0 8-bit write of an even address
0 1 0 8-bit write of an odd address
Chapter 18 Multiplexed External Bus Interface (MEBIV3)
MC9S12KG128 Data Sheet, Rev. 1.16
538 Freescale Semiconductor
18.4.2 Stretched Bus Cycles
In order to allow fast internal bus cycles to coexist in a system with slower external memory resources, the
HCS12 supports the concept of stretched bus cycles (module timing reference clocks for timers and baud
rate generators are not affected by this stretching). Control bits in the MISC register in the MMC sub-block
of the core specify the amount of stretch (0, 1, 2, or 3 periods of the internal bus-rate clock). While
stretching, the CPU state machines are all held in their current state. At this point in the CPU bus cycle,
write data would already be driven onto the data bus so the length of time write data is valid is extended
in the case of a stretched bus cycle. Read data would not be captured by the system until the E clock falling
edge. In the case of a stretched bus cycle, read data is not required until the specified setup time before the
falling edge of the stretched E clock. The chip selects, and R/W signals remain valid during the period of
stretching (throughout the stretched E high time).
NOTE
The address portion of the bus cycle is not stretched.
18.4.3 Modes of Operation
The operating mode out of reset is determined by the states of the MODC, MODB, and MODA pins during
reset (Table 18-16). The MODC, MODB, and MODA bits in the MODE register show the current
operating mode and provide limited mode switching during operation. The states of the MODC, MODB,
and MODA pins are latched into these bits on the rising edge of the reset signal.
0 0 1 16-bit read of an even address
1 1 1 16-bit read of an odd address
(low/high data swapped)
0 0 0 16-bit write to an even address
1 1 0 16-bit write to an odd address
(low/high data swapped)
Table 18-16. Mode Selection
MODC MODB MODA Mode Description
0 0 0 Special Single Chip, BDM allowed and ACTIVE. BDM is allowed in all
other modes but a serial command is required to make BDM active.
0 0 1 Emulation Expanded Narrow, BDM allowed
0 1 0 Special Test (Expanded Wide), BDM allowed
0 1 1 Emulation Expanded Wide, BDM allowed
1 0 0 Normal Single Chip, BDM allowed
1 0 1 Normal Expanded Narrow, BDM allowed
1 1 0 Peripheral; BDM allowed but bus operations would cause bus conflicts
(must not be used)
1 1 1 Normal Expanded Wide, BDM allowed
Table 18-15. Access Type vs. Bus Control Pins
LSTRB AB0 R/W Type of Access
Chapter 18 Multiplexed External Bus Interface (MEBIV3)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 539
There are two basic types of operating modes:
1. Normal modes: Some registers and bits are protected against accidental changes.
2. Special modes: Allow greater access to protected control registers and bits for special purposes
such as testing.
A system development and debug feature, background debug mode (BDM), is available in all modes. In
special single-chip mode, BDM is active immediately after reset.
Some aspects of Port E are not mode dependent. Bit 1 of Port E is a general purpose input or the IRQ
interrupt input. IRQ can be enabled by bits in the CPU’s condition codes register but it is inhibited at reset
so this pin is initially configured as a simple input with a pull-up. Bit 0 of Port E is a general purpose input
or the XIRQ interrupt input. XIRQ can be enabled by bits in the CPU’s condition codes register but it is
inhibited at reset so this pin is initially configured as a simple input with a pull-up. The ESTR bit in the
EBICTL register is set to one by reset in any user mode. This assures that the reset vector can be fetched
even if it is located in an external slow memory device. The PE6/MODB/IPIPE1 and PE5/MODA/IPIPE0
pins act as high-impedance mode select inputs during reset.
The following paragraphs discuss the default bus setup and describe which aspects of the bus can be
changed after reset on a per mode basis.
18.4.3.1 Normal Operating Modes
These modes provide three operating configurations. Background debug is available in all three modes, but
must first be enabled for some operations by means of a BDM background command, then activated.
18.4.3.1.1 Normal Single-Chip Mode
There is no external expansion bus in this mode. All pins of Ports A, B and E are configured as general
purpose I/O pins Port E bits 1 and 0 are available as general purpose input only pins with internal pull
resistors enabled. All other pins of Port E are bidirectional I/O pins that are initially configured as
high-impedance inputs with internal pull resistors enabled. Ports A and B are configured as
high-impedance inputs with their internal pull resistors disabled.
The pins associated with Port E bits 6, 5, 3, and 2 cannot be configured for their alternate functions IPIPE1,
IPIPE0, LSTRB, and R/W while the MCU is in single chip modes. In single chip modes, the associated
control bits PIPOE, LSTRE, and RDWE are reset to zero. Writing the opposite state into them in single
chip mode does not change the operation of the associated Port E pins.
In normal single chip mode, the MODE register is writable one time. This allows a user program to change
the bus mode to narrow or wide expanded mode and/or turn on visibility of internal accesses.
Port E, bit 4 can be configured for a free-running E clock output by clearing NECLK=0. Typically the only
use for an E clock output while the MCU is in single chip modes would be to get a constant speed clock
for use in the external application system.
Chapter 18 Multiplexed External Bus Interface (MEBIV3)
MC9S12KG128 Data Sheet, Rev. 1.16
540 Freescale Semiconductor
18.4.3.1.2 Normal Expanded Wide Mode
In expanded wide modes, Ports A and B are configured as a 16-bit multiplexed address and data bus and
Port E bit 4 is configured as the E clock output signal. These signals allow external memory and peripheral
devices to be interfaced to the MCU.
Port E pins other than PE4/ECLK are configured as general purpose I/O pins (initially high-impedance
inputs with internal pull resistors enabled). Control bits PIPOE, NECLK, LSTRE, and RDWE in the
PEAR register can be used to configure Port E pins to act as bus control outputs instead of general purpose
I/O pins.
It is possible to enable the pipe status signals on Port E bits 6 and 5 by setting the PIPOE bit in PEAR, but
it would be unusual to do so in this mode. Development systems where pipe status signals are monitored
would typically use the special variation of this mode.
The Port E bit 2 pin can be reconfigured as the R/W bus control signal by writing “1” to the RDWE bit in
PEAR. If the expanded system includes external devices that can be written, such as RAM, the RDWE bit
would need to be set before any attempt to write to an external location. If there are no writable resources
in the external system, PE2 can be left as a general purpose I/O pin.
The Port E bit 3 pin can be reconfigured as the LSTRB bus control signal by writing “1” to the LSTRE bit
in PEAR. The default condition of this pin is a general purpose input because the LSTRB function is not
needed in all expanded wide applications.
The Port E bit 4 pin is initially configured as ECLK output with stretch. The E clock output function
depends upon the settings of the NECLK bit in the PEAR register, the IVIS bit in the MODE register and
the ESTR bit in the EBICTL register. The E clock is available for use in external select decode logic or as
a constant speed clock for use in the external application system.
18.4.3.1.3 Normal Expanded Narrow Mode
This mode is used for lower cost production systems that use 8-bit wide external EPROMs or RAMs. Such
systems take extra bus cycles to access 16-bit locations but this may be preferred over the extra cost of
additional external memory devices.
Ports A and B are configured as a 16-bit address bus and Port A is multiplexed with data. Internal visibility
is not available in this mode because the internal cycles would need to be split into two 8-bit cycles.
Since the PEAR register can only be written one time in this mode, use care to set all bits to the desired
states during the single allowed write.
The PE3/LSTRB pin is always a general purpose I/O pin in normal expanded narrow mode. Although it is
possible to write the LSTRE bit in PEAR to “1” in this mode, the state of LSTRE is overridden and Port
E bit 3 cannot be reconfigured as the LSTRB output.
It is possible to enable the pipe status signals on Port E bits 6 and 5 by setting the PIPOE bit in PEAR, but
it would be unusual to do so in this mode. LSTRB would also be needed to fully understand system
activity. Development systems where pipe status signals are monitored would typically use special
expanded wide mode or occasionally special expanded narrow mode.
Chapter 18 Multiplexed External Bus Interface (MEBIV3)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 541
The PE4/ECLK pin is initially configured as ECLK output with stretch. The E clock output function
depends upon the settings of the NECLK bit in the PEAR register, the IVIS bit in the MODE register and
the ESTR bit in the EBICTL register. In normal expanded narrow mode, the E clock is available for use in
external select decode logic or as a constant speed clock for use in the external application system.
The PE2/R/W pin is initially configured as a general purpose input with an internal pull resistor enabled
but this pin can be reconfigured as the R/W bus control signal by writing “1” to the RDWE bit in PEAR.
If the expanded narrow system includes external devices that can be written such as RAM, the RDWE bit
would need to be set before any attempt to write to an external location. If there are no writable resources
in the external system, PE2 can be left as a general purpose I/O pin.
18.4.3.1.4 Emulation Expanded Wide Mode
In expanded wide modes, Ports A and B are configured as a 16-bit multiplexed address and data bus and
Port E provides bus control and status signals. These signals allow external memory and peripheral devices
to be interfaced to the MCU. These signals can also be used by a logic analyzer to monitor the progress of
application programs.
The bus control related pins in Port E (PE7/NOACC, PE6/MODB/IPIPE1, PE5/MODA/IPIPE0,
PE4/ECLK, PE3/LSTRB/TAGLO, and PE2/R/W) are all configured to serve their bus control output
functions rather than general purpose I/O. Notice that writes to the bus control enable bits in the PEAR
register in emulation mode are restricted.
18.4.3.1.5 Emulation Expanded Narrow Mode
Expanded narrow modes are intended to allow connection of single 8-bit external memory devices for
lower cost systems that do not need the performance of a full 16-bit external data bus. Accesses to internal
resources that have been mapped external (i.e. PORTA, PORTB, DDRA, DDRB, PORTE, DDRE, PEAR,
PUCR, RDRIV) will be accessed with a 16-bit data bus on Ports A and B. Accesses of 16-bit external
words to addresses which are normally mapped external will be broken into two separate 8-bit accesses
using Port A as an 8-bit data bus. Internal operations continue to use full 16-bit data paths. They are only
visible externally as 16-bit information if IVIS=1.
Ports A and B are configured as multiplexed address and data output ports. During external accesses,
address A15, data D15 and D7 are associated with PA7, address A0 is associated with PB0 and data D8
and D0 are associated with PA0. During internal visible accesses and accesses to internal resources that
have been mapped external, address A15 and data D15 is associated with PA7 and address A0 and data
D0 is associated with PB0.
The bus control related pins in Port E (PE7/NOACC, PE6/MODB/IPIPE1, PE5/MODA/IPIPE0,
PE4/ECLK, PE3/LSTRB/TAGLO, and PE2/R/W) are all configured to serve their bus control output
functions rather than general purpose I/O. Notice that writes to the bus control enable bits in the PEAR
register in emulation mode are restricted.
The main difference between special modes and normal modes is that some of the bus control and system
control signals cannot be written in emulation modes.
Chapter 18 Multiplexed External Bus Interface (MEBIV3)
MC9S12KG128 Data Sheet, Rev. 1.16
542 Freescale Semiconductor
18.4.3.2 Special Operating Modes
There are two special operating modes that correspond to normal operating modes. These operating modes
are commonly used in factory testing and system development.
18.4.3.2.1 Special Single-Chip Mode
When the MCU is reset in this mode, the background debug mode is enabled and active. The MCU does
not fetch the reset vector and execute application code as it would in other modes. Instead the active
background mode is in control of CPU execution and BDM firmware is waiting for additional serial
commands through the BKGD pin. When a serial command instructs the MCU to return to normal
execution, the system will be configured as described below unless the reset states of internal control
registers have been changed through background commands after the MCU was reset.
There is no external expansion bus after reset in this mode. Ports A and B are initially simple bidirectional
I/O pins that are configured as high-impedance inputs with internal pull resistors disabled; however,
writing to the mode select bits in the MODE register (which is allowed in special modes) can change this
after reset. All of the Port E pins (except PE4/ECLK) are initially configured as general purpose
high-impedance inputs with internal pull resistors enabled. PE4/ECLK is configured as the E clock output
in this mode.
The pins associated with Port E bits 6, 5, 3, and 2 cannot be configured for their alternate functions IPIPE1,
IPIPE0, LSTRB, and R/W while the MCU is in single chip modes. In single chip modes, the associated
control bits PIPOE, LSTRE and RDWE are reset to zero. Writing the opposite value into these bits in
single chip mode does not change the operation of the associated Port E pins.
Port E, bit 4 can be configured for a free-running E clock output by clearing NECLK=0. Typically the only
use for an E clock output while the MCU is in single chip modes would be to get a constant speed clock
for use in the external application system.
18.4.3.2.2 Special Test Mode
In expanded wide modes, Ports A and B are configured as a 16-bit multiplexed address and data bus and
Port E provides bus control and status signals. In special test mode, the write protection of many control
bits is lifted so that they can be thoroughly tested without needing to go through reset.
18.4.3.3 Test Operating Mode
There is a test operating mode in which an external master, such as an I.C. tester, can control the on-chip
peripherals.
18.4.3.3.1 Peripheral Mode
This mode is intended for factory testing of the MCU. In this mode, the CPU is inactive and an external
(tester) bus master drives address, data and bus control signals in through Ports A, B and E. In effect, the
whole MCU acts as if it was a peripheral under control of an external CPU. This allows faster testing of
on-chip memory and peripherals than previous testing methods. Since the mode control register is not
accessible in peripheral mode, the only way to change to another mode is to reset the MCU into a different
Chapter 18 Multiplexed External Bus Interface (MEBIV3)
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 543
mode. Background debugging should not be used while the MCU is in special peripheral mode as internal
bus conflicts between BDM and the external master can cause improper operation of both functions.
18.4.4 Internal Visibility
Internal visibility is available when the MCU is operating in expanded wide modes or emulation narrow
mode. It is not available in single-chip, peripheral or normal expanded narrow modes. Internal visibility is
enabled by setting the IVIS bit in the MODE register.
If an internal access is made while E, R/W, and LSTRB are configured as bus control outputs and internal
visibility is off (IVIS=0), E will remain low for the cycle, R/W will remain high, and address, data and the
LSTRB pins will remain at their previous state.
When internal visibility is enabled (IVIS=1), certain internal cycles will be blocked from going external.
During cycles when the BDM is selected, R/W will remain high, data will maintain its previous state, and
address and LSTRB pins will be updated with the internal value. During CPU no access cycles when the
BDM is not driving, R/W will remain high, and address, data and the LSTRB pins will remain at their
previous state.
NOTE
When the system is operating in a secure mode, internal visibility is not
available (i.e., IVIS = 1 has no effect). Also, the IPIPE signals will not be
visible, regardless of operating mode. IPIPE1–IPIPE0 will display 0es if
they are enabled. In addition, the MOD bits in the MODE control register
cannot be written.
18.4.5 Low-Power Options
The MEBI does not contain any user-controlled options for reducing power consumption. The operation
of the MEBI in low-power modes is discussed in the following subsections.
18.4.5.1 Operation in Run Mode
The MEBI does not contain any options for reducing power in run mode; however, the external addresses
are conditioned to reduce power in single-chip modes. Expanded bus modes will increase power
consumption.
18.4.5.2 Operation in Wait Mode
The MEBI does not contain any options for reducing power in wait mode.
18.4.5.3 Operation in Stop Mode
The MEBI will cease to function after execution of a CPU STOP instruction.
Chapter 18 Multiplexed External Bus Interface (MEBIV3)
MC9S12KG128 Data Sheet, Rev. 1.16
544 Freescale Semiconductor
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 545
Chapter 19
Module Mapping Control (MMCV4) Block Description
19.1 Introduction
This section describes the functionality of the module mapping control (MMC) sub-block of the S12 core
platform.
The block diagram of the MMC is shown in Figure 19-1.
Figure 19-1. MMC Block Diagram
The MMC is the sub-module which controls memory map assignment and selection of internal resources
and external space. Internal buses between the core and memories and between the core and peripherals is
controlled in this module. The memory expansion is generated in this module.
MMC
MODE INFORMATION
REGISTERS
CPU WRITE DATA BUS
CPU ADDRESS BUS
CPU CONTROL
STOP, WAIT
ADDRESS DECODE
CPU READ DATA BUS
EBI ALTERNATE ADDRESS BUS
EBI ALTERNATE WRITE DATA BUS
EBI ALTERNATE READ DATA BUS
SECURITY
CLOCKS, RESET
READ & WRITE ENABLES
ALTERNATE ADDRESS BUS (BDM)
ALTERNATE WRITE DATA BUS (BDM)
ALTERNATE READ DATA BUS (BDM)
CORE SELECT (S)
PORT K INTERFACE
MEMORY SPACE SELECT(S)
PERIPHERAL SELECT
BUS CONTROL
SECURE
BDM_UNSECURE
MMC_SECURE
INTERNAL MEMORY
EXPANSION
Chapter 19 Module Mapping Control (MMCV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
546 Freescale Semiconductor
19.1.1 Features
Registers for mapping of address space for on-chip RAM, EEPROM, and FLASH (or ROM)
memory blocks and associated registers
Memory mapping control and selection based upon address decode and system operating mode
Core address bus control
Core data bus control and multiplexing
Core security state decoding
Emulation chip select signal generation (ECS)
External chip select signal generation (XCS)
Internal memory expansion
External stretch and ROM mapping control functions via the MISC register
Reserved registers for test purposes
Configurable system memory options defined at integration of core into the system-on-a-chip
(SoC).
19.1.2 Modes of Operation
Some of the registers operate differently depending on the mode of operation (i.e., normal expanded wide,
special single chip, etc.). This is best understood from the register descriptions.
19.2 External Signal Description
All interfacing with the MMC sub-block is done within the core, it has no external signals.
19.3 Memory Map and Register Definition
A summary of the registers associated with the MMC sub-block is shown in Figure 19-2. Detailed
descriptions of the registers and bits are given in the subsections that follow.
19.3.1 Module Memory Map
Table 19-1. MMC Memory Map
Address
Offset Register Access
0x0010 Initialization of Internal RAM Position Register (INITRM) R/W
0x0011 Initialization of Internal Registers Position Register (INITRG) R/W
0x0012 Initialization of Internal EEPROM Position Register (INITEE) R/W
0x0013 Miscellaneous System Control Register (MISC) R/W
0x0014 Reserved
.
..
.
Chapter 19 Module Mapping Control (MMCV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 547
0x0017 Reserved
.
..
.
0x001C Memory Size Register 0 (MEMSIZ0) R
0x001D Memory Size Register 1 (MEMSIZ1) R
.
..
.
0x0030 Program Page Index Register (PPAGE) R/W
0x0031 Reserved
Table 19-1. MMC Memory Map (continued)
Address
Offset Register Access
Chapter 19 Module Mapping Control (MMCV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
548 Freescale Semiconductor
19.3.2 Register Descriptions
Name Bit 7 6 5 4321Bit 0
0x0010
INITRM RRAM15 RAM14 RAM13 RAM12 RAM11 00
RAMHAL
W
0x0011
INITRG R0 REG14 REG13 REG12 REG11 000
W
0x0012
INITEE REE15 EE14 EE13 EE12 EE11 00
EEON
W
0x0013
MISC R0000
EXSTR1 EXSTR0 ROMHM ROMON
W
0x0014
MTSTO R Bit 7 6 5 4321Bit 0
W
0x0017
MTST1 R Bit 7 6 5 4321Bit 0
W
0x001C
MEMSIZ0 R REG_SW0 0 EEP_SW1 EEP_SW0 0 RAM_SW2 RAM_SW1 RAM_SW0
W
0x001D
MEMSIZ1 R ROM_SW1 ROM_SW0 0 0 0 0 PAG_SW1 PAG_SW0
W
0x0030
PPAGE R0 0 PIX5 PIX4 PIX3 PIX2 PIX1 PIX0
W
0x0031
Reserved R00000000
W
= Unimplemented
Figure 19-2. MMC Register Summary
Chapter 19 Module Mapping Control (MMCV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 549
19.3.2.1 Initialization of Internal RAM Position Register (INITRM)
Read: Anytime
Write: Once in normal and emulation modes, anytime in special modes
NOTE
Writes to this register take one cycle to go into effect.
This register initializes the position of the internal RAM within the on-chip system memory map.
Module Base + 0x0010
Starting address location affected by INITRG register setting.
76543210
RRAM15 RAM14 RAM13 RAM12 RAM11 00
RAMHAL
W
Reset 0 0 0 01001
= Unimplemented or Reserved
Figure 19-3. Initialization of Internal RAM Position Register (INITRM)
Table 19-2. INITRM Field Descriptions
Field Description
7:3
RAM[15:11] Internal RAM Map Position — These bits determine the upper five bits of the base address for the system’s
internal RAM array.
0
RAMHAL RAM High-Align — RAMHAL specifies the alignment of the internal RAM array.
0 Aligns the RAM to the lowest address (0x0000) of the mappable space
1 Aligns the RAM to the higher address (0xFFFF) of the mappable space
Chapter 19 Module Mapping Control (MMCV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
550 Freescale Semiconductor
19.3.2.2 Initialization of Internal Registers Position Register (INITRG)
Read: Anytime
Write: Once in normal and emulation modes and anytime in special modes
This register initializes the position of the internal registers within the on-chip system memory map. The
registers occupy either a 1K byte or 2K byte space and can be mapped to any 2K byte space within the first
32K bytes of the system’s address space.
Module Base + 0x0011
Starting address location affected by INITRG register setting.
76543210
R0 REG14 REG13 REG12 REG11 000
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 19-4. Initialization of Internal Registers Position Register (INITRG)
Table 19-3. INITRG Field Descriptions
Field Description
6:3
REG[14:11] Internal Register Map Position — These four bits in combination with the leading zero supplied by bit 7 of
INITRG determine the upper five bits of the base address for the system’s internal registers (i.e., the minimum
base address is 0x0000 and the maximum is 0x7FFF).
Chapter 19 Module Mapping Control (MMCV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 551
19.3.2.3 Initialization of Internal EEPROM Position Register (INITEE)
Read: Anytime
Write: The EEON bit can be written to any time on all devices. Bits E[11:15] are “write anytime in all
modes” on most devices. On some devices, bits E[11:15] are “write once in normal and emulation modes
and write anytime in special modes”. See device overview chapter to determine the actual write access
rights.
NOTE
Writes to this register take one cycle to go into effect.
This register initializes the position of the internal EEPROM within the on-chip system memory map.
Module Base + 0x0012
Starting address location affected by INITRG register setting.
76543210
REE15 EE14 EE13 EE12 EE11 00
EEON
W
Reset1————————
1. The reset state of this register is controlled at chip integration. Please refer to the device overview section to determine the
actual reset state of this register.
= Unimplemented or Reserved
Figure 19-5. Initialization of Internal EEPROM Position Register (INITEE)
Table 19-4. INITEE Field Descriptions
Field Description
7:3
EE[15:11] Internal EEPROM Map Position These bits determinetheupper fivebits of the base address forthe system’s
internal EEPROM array.
0
EEON Enable EEPROM — This bit is used to enable the EEPROM memory in the memory map.
0 Disables the EEPROM from the memory map.
1 Enables the EEPROM in the memory map at the address selected by EE[15:11].
Chapter 19 Module Mapping Control (MMCV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
552 Freescale Semiconductor
19.3.2.4 Miscellaneous System Control Register (MISC)
Read: Anytime
Write: As stated in each bit description
NOTE
Writes to this register take one cycle to go into effect.
This register initializes miscellaneous control functions.
Module Base + 0x0013
Starting address location affected by INITRG register setting.
76543210
R0000
EXSTR1 EXSTR0 ROMHM ROMON
W
Reset: Expanded
or Emulation 0000110
1
Reset: Peripheral
or Single Chip 00001101
Reset: Special Test 00001100
1. The reset state of this bit is determined at the chip integration level.
= Unimplemented or Reserved
Figure 19-6. Miscellaneous System Control Register (MISC)
Table 19-5. INITEE Field Descriptions
Field Description
3:2
EXSTR[1:0] External Access Stretch Bits 1 and 0
Write: once in normal and emulation modes and anytime in special modes
This two-bit field determines the amount of clock stretch on accesses to the external address space as shown in
Table 19-6. In single chip and peripheral modes these bits have no meaning or effect.
1
ROMHM FLASH EEPROM or ROM Only in Second Half of Memory Map
Write: once in normal and emulation modes and anytime in special modes
0 The fixed page(s) of FLASH EEPROM or ROM in the lower half of the memory map can be accessed.
1 Disables direct access to the FLASH EEPROM or ROM in the lower half of the memory map. These physical
locations of the FLASH EEPROM or ROM remain accessible through the program page window.
0
ROMON ROMON — Enable FLASH EEPROM or ROM
Write: once in normal and emulation modes and anytime in special modes
This bit is used to enable the FLASH EEPROM or ROM memory in the memory map.
0 Disables the FLASH EEPROM or ROM from the memory map.
1 Enables the FLASH EEPROM or ROM in the memory map.
Chapter 19 Module Mapping Control (MMCV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 553
19.3.2.5 Reserved Test Register 0 (MTST0)
Read: Anytime
Write: No effect — this register location is used for internal test purposes.
19.3.2.6 Reserved Test Register 1 (MTST1)
Read: Anytime
Write: No effect — this register location is used for internal test purposes.
Table 19-6. External Stretch Bit Definition
Stretch Bit EXSTR1 Stretch Bit EXSTR0 Number of E Clocks Stretched
00 0
01 1
10 2
11 3
Module Base + 0x0014
Starting address location affected by INITRG register setting.
76543210
R00000000
W
Reset 0 0 0 00000
= Unimplemented or Reserved
Figure 19-7. Reserved Test Register 0 (MTST0)
Module Base + 0x0017
Starting address location affected by INITRG register setting.
76543210
R00000000
W
Reset 0 0 0 10000
= Unimplemented or Reserved
Figure 19-8. Reserved Test Register 1 (MTST1)
Chapter 19 Module Mapping Control (MMCV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
554 Freescale Semiconductor
19.3.2.7 Memory Size Register 0 (MEMSIZ0)
Read: Anytime
Write: Writes have no effect
Reset: Defined at chip integration, see device overview section.
The MEMSIZ0 register reflects the state of the register, EEPROM and RAM memory space configuration
switches at the core boundary which are configured at system integration. This register allows read
visibility to the state of these switches.
Module Base + 0x001C
Starting address location affected by INITRG register setting.
76543210
R REG_SW0 0 EEP_SW1 EEP_SW0 0 RAM_SW2 RAM_SW1 RAM_SW0
W
Reset ——————
= Unimplemented or Reserved
Figure 19-9. Memory Size Register 0 (MEMSIZ0)
Table 19-7. MEMSIZ0 Field Descriptions
Field Description
7
REG_SW0 Allocated System Register Space
0 Allocated system register space size is 1K byte
1 Allocated system register space size is 2K byte
5:4
EEP_SW[1:0] Allocated System EEPROM Memory Space — The allocated system EEPROM memory space size is as
given in Table 19-8.
2
RAM_SW[2:0] Allocated System RAM Memory Space — The allocated system RAM memory space size is as given in
Table 19-9.
Table 19-8. Allocated EEPROM Memory Space
eep_sw1:eep_sw0 Allocated EEPROM Space
00 0K byte
01 2K bytes
10 4K bytes
11 8K bytes
Table 19-9. Allocated RAM Memory Space
ram_sw2:ram_sw0 Allocated
RAM Space RAM
Mappable Region INITRM
Bits Used RAM Reset
Base Address1
000 2K bytes 2K bytes RAM[15:11] 0x0800
001 4K bytes 4K bytes RAM[15:12] 0x0000
010 6K bytes 8K bytes2RAM[15:13] 0x0800
Chapter 19 Module Mapping Control (MMCV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 555
NOTE
As stated, the bits in this register provide read visibility to the system
physical memory space allocations defined at system integration. The actual
array size for any given type of memory block may differ from the allocated
size. Please refer to the device overview chapter for actual sizes.
19.3.2.8 Memory Size Register 1 (MEMSIZ1)
Read: Anytime
Write: Writes have no effect
Reset: Defined at chip integration, see device overview section.
The MEMSIZ1 register reflects the state of the FLASH or ROM physical memory space and paging
switches at the core boundary which are configured at system integration. This register allows read
visibility to the state of these switches.
011 8K bytes 8K bytes RAM[15:13] 0x0000
100 10K bytes 16K bytes 2RAM[15:14] 0x1800
101 12K bytes 16K bytes 2RAM[15:14] 0x1000
110 14K bytes 16K bytes 2RAM[15:14] 0x0800
111 16K bytes 16K bytes RAM[15:14] 0x0000
1The RAM Reset BASE Address is based on the reset value of the INITRM register, 0x0009.
2Alignment of the Allocated RAM space within the RAM mappable region is dependent on the value of RAMHAL.
Module Base + 0x001D
Starting address location affected by INITRG register setting.
76543210
R ROM_SW1 ROM_SW0 0 0 0 0 PAG_SW1 PAG_SW0
W
Reset ——————
= Unimplemented or Reserved
Figure 19-10. Memory Size Register 1 (MEMSIZ1)
Table 19-9. Allocated RAM Memory Space (continued)
ram_sw2:ram_sw0 Allocated
RAM Space RAM
Mappable Region INITRM
Bits Used RAM Reset
Base Address1
Chapter 19 Module Mapping Control (MMCV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
556 Freescale Semiconductor
NOTE
As stated, the bits in this register provide read visibility to the system
memory space and on-chip/off-chip partitioning allocations defined at
system integration. The actual array size for any given type of memory
block may differ from the allocated size. Please refer to the device overview
chapter for actual sizes.
Table 19-10. MEMSIZ0 Field Descriptions
Field Description
7:6
ROM_SW[1:0] Allocated System FLASH or ROM Physical Memory Space — The allocated system FLASH or ROM
physical memory space is as given in Table 19-11.
1:0
PAG_SW[1:0] Allocated Off-Chip FLASH or ROM Memory Space The allocated off-chip FLASH or ROM memory space
size is as given in Table 19-12.
Table 19-11. Allocated FLASH/ROM Physical Memory Space
rom_sw1:rom_sw0 Allocated FLASH
or ROM Space
00 0K byte
01 16K bytes
10 48K bytes(1)
11 64K bytes(1)
NOTES:
1. The ROMHM software bit in the MISC register determines the accessibility of the
FLASH/ROM memory space. Please refer to Section 19.3.2.8, “Memory Size Register
1 (MEMSIZ1),” for a detailed functional description of the ROMHM bit.
Table 19-12. Allocated Off-Chip Memory Options
pag_sw1:pag_sw0 Off-Chip Space On-Chip Space
00 876K bytes 128K bytes
01 768K bytes 256K bytes
10 512K bytes 512K bytes
11 0K byte 1M byte
Chapter 19 Module Mapping Control (MMCV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 557
19.3.2.9 Program Page Index Register (PPAGE)
Read: Anytime
Write: Determined at chip integration. Generally it’s: “write anytime in all modes;” on some devices it will
be: “write only in special modes.” Check specific device documentation to determine which applies.
Reset: Defined at chip integration as either 0x00 (paired with write in any mode) or 0x3C (paired with
write only in special modes), see device overview chapter.
The HCS12 core architecture limits the physical address space available to 64K bytes. The program page
index register allows for integrating up to 1M byte of FLASH or ROM into the system by using the six
page index bits to page 16K byte blocks into the program page window located from 0x8000 to 0xBFFF
as defined in Table 19-14. CALL and RTC instructions have special access to read and write this register
without using the address bus.
NOTE
Normal writes to this register take one cycle to go into effect. Writes to this
register using the special access of the CALL and RTC instructions will be
complete before the end of the associated instruction.
Module Base + 0x0030
Starting address location affected by INITRG register setting.
76543210
R0 0 PIX5 PIX4 PIX3 PIX2 PIX1 PIX0
W
Reset1————————
1. The reset state of this register is controlled at chip integration. Please refer to the device overview section to determine the
actual reset state of this register.
= Unimplemented or Reserved
Figure 19-11. Program Page Index Register (PPAGE)
Table 19-13. MEMSIZ0 Field Descriptions
Field Description
5:0
PIX[5:0] Program Page Index Bits 5:0 — These page index bits are used to select which of the 64 FLASH or ROM
array pages is to be accessed in the program page window as shown in Table 19-14.
Chapter 19 Module Mapping Control (MMCV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
558 Freescale Semiconductor
19.4 Functional Description
The MMC sub-block performs four basic functions of the core operation: bus control, address decoding
and select signal generation, memory expansion, and security decoding for the system. Each aspect is
described in the following subsections.
19.4.1 Bus Control
The MMC controls the address bus and data buses that interface the core with the rest of the system. This
includes the multiplexing of the input data buses to the core onto the main CPU read data bus and control
of data flow from the CPU to the output address and data buses of the core. In addition, the MMC manages
all CPU read data bus swapping operations.
19.4.2 Address Decoding
As data flows on the core address bus, the MMC decodes the address information, determines whether the
internal core register or firmware space, the peripheral space or a memory register or array space is being
addressed and generates the correct select signal. This decoding operation also interprets the mode of
operation of the system and the state of the mapping control registers in order to generate the proper select.
The MMC also generates two external chip select signals, emulation chip select (ECS) and external chip
select (XCS).
19.4.2.1 Select Priority and Mode Considerations
Although internal resources such as control registers and on-chip memory have default addresses, each can
be relocated by changing the default values in control registers. Normally, I/O addresses, control registers,
Table 19-14. Program Page Index Register Bits
PIX5 PIX4 PIX3 PIX2 PIX1 PIX0 Program Space
Selected
000000 16K page 0
000001 16K page 1
000010 16K page 2
000011 16K page 3
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
111100 16K page 60
111101 16K page 61
111110 16K page 62
111111 16K page 63
Chapter 19 Module Mapping Control (MMCV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 559
vector spaces, expansion windows, and on-chip memory are mapped so that their address ranges do not
overlap. The MMC will make only one select signal active at any given time. This activation is based upon
the priority outlined in Table 19-15. If two or more blocks share the same address space, only the select
signal for the block with the highest priority will become active. An example of this is if the registers and
the RAM are mapped to the same space, the registers will have priority over the RAM and the portion of
RAM mapped in this shared space will not be accessible. The expansion windows have the lowest priority.
This means that registers, vectors, and on-chip memory are always visible to a program regardless of the
values in the page select registers.
In expanded modes, all address space not used by internal resources is by default external memory space.
The data registers and data direction registers for ports A and B are removed from the on-chip memory
map and become external accesses. If the EME bit in the MODE register (see MEBI block description
chapter) is set, the data and data direction registers for port E are also removed from the on-chip memory
map and become external accesses.
In special peripheral mode, the first 16 registers associated with bus expansion are removed from the
on-chip memory map (PORTA, PORTB, DDRA, DDRB, PORTE, DDRE, PEAR, MODE, PUCR,
RDRIV, and the EBI reserved registers).
In emulation modes, if the EMK bit in the MODE register (see MEBI block description chapter) is set, the
data and data direction registers for port K are removed from the on-chip memory map and become
external accesses.
19.4.2.2 Emulation Chip Select Signal
When the EMK bit in the MODE register (see MEBI block description chapter) is set, port K bit 7 is used
as an active-low emulation chip select signal, ECS. This signal is active when the system is in emulation
mode, the EMK bit is set and the FLASH or ROM space is being addressed subject to the conditions
outlined in Section 19.4.3.2, “Extended Address (XAB19:14) and ECS Signal Functionality.” When the
EMK bit is clear, this pin is used for general purpose I/O.
19.4.2.3 External Chip Select Signal
When the EMK bit in the MODE register (see MEBI block description chapter) is set, port K bit 6 is used
as an active-low external chip select signal, XCS. This signal is active only when the ECS signal described
above is not active and when the system is addressing the external address space. Accesses to
Table 19-15. Select Signal Priority
Priority Address Space
Highest BDM (internal to core) firmware or register space
... Internal register space
... RAM memory block
... EEPROM memory block
... On-chip FLASH or ROM
Lowest Remaining external space
Chapter 19 Module Mapping Control (MMCV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
560 Freescale Semiconductor
unimplemented locations within the register space or to locations that are removed from the map (i.e., ports
A and B in expanded modes) will not cause this signal to become active. When the EMK bit is clear, this
pin is used for general purpose I/O.
19.4.3 Memory Expansion
The HCS12 core architecture limits the physical address space available to 64K bytes. The program page
index register allows for integrating up to 1M byte of FLASH or ROM into the system by using the six
page index bits to page 16K byte blocks into the program page window located from 0x8000 to 0xBFFF
in the physical memory space. The paged memory space can consist of solely on-chip memory or a
combination of on-chip and off-chip memory. This partitioning is configured at system integration through
the use of the paging configuration switches (pag_sw1:pag_sw0) at the core boundary. The options
available to the integrator are as given in Table 19-16 (this table matches Table 19-12 but is repeated here
for easy reference).
Based upon the system configuration, the program page window will consider its access to be either
internal or external as defined in Table 19-17.
NOTE
The partitioning as defined in Table 19-17 applies only to the allocated
memory space and the actual on-chip memory sizes implemented in the
system may differ. Please refer to the device overview chapter for actual
sizes.
Table 19-16. Allocated Off-Chip Memory Options
pag_sw1:pag_sw0 Off-Chip Space On-Chip Space
00 876K bytes 128K bytes
01 768K bytes 256K bytes
10 512K bytes 512K bytes
11 0K byte 1M byte
Table 19-17. External/Internal Page Window Access
pag_sw1:pag_sw0 Partitioning PIX5:0 Value Page Window
Access
00 876K off-Chip,
128K on-Chip 0x0000–0x0037 External
0x0038–0x003F Internal
01 768K off-chip,
256K on-chip 0x0000–0x002F External
0x0030–0x003F Internal
10 512K off-chip,
512K on-chip 0x0000–0x001F External
0x0020–0x003F Internal
11 0K off-chip,
1M on-chip N/A External
0x0000–0x003F Internal
Chapter 19 Module Mapping Control (MMCV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 561
The PPAGE register holds the page select value for the program page window. The value of the PPAGE
register can be manipulated by normal read and write (some devices don’t allow writes in some modes)
instructions as well as the CALL and RTC instructions.
Control registers, vector spaces, and a portion of on-chip memory are located in unpaged portions of the
64K byte physical address space. The stack and I/O addresses should also be in unpaged memory to make
them accessible from any page.
The starting address of a service routine must be located in unpaged memory because the 16-bit exception
vectors cannot point to addresses in paged memory. However, a service routine can call other routines that
are in paged memory. The upper 16K byte block of memory space (0xC000–0xFFFF) is unpaged. It is
recommended that all reset and interrupt vectors point to locations in this area.
19.4.3.1 CALL and Return from Call Instructions
CALL and RTC are uninterruptable instructions that automate page switching in the program expansion
window. CALL is similar to a JSR instruction, but the subroutine that is called can be located anywhere in
the normal 64K byte address space or on any page of program expansion memory. CALL calculates and
stacks a return address, stacks the current PPAGE value, and writes a new instruction-supplied value to
PPAGE. The PPAGE value controls which of the 64 possible pages is visible through the 16K byte
expansion window in the 64K byte memory map. Execution then begins at the address of the called
subroutine.
During the execution of a CALL instruction, the CPU:
Writes the old PPAGE value into an internal temporary register and writes the new
instruction-supplied PPAGE value into the PPAGE register.
Calculates the address of the next instruction after the CALL instruction (the return address), and
pushes this 16-bit value onto the stack.
Pushes the old PPAGE value onto the stack.
Calculates the effective address of the subroutine, refills the queue, and begins execution at the new
address on the selected page of the expansion window.
This sequence is uninterruptable; there is no need to inhibit interrupts during CALL execution. A CALL
can be performed from any address in memory to any other address.
The PPAGE value supplied by the instruction is part of the effective address. For all addressing mode
variations except indexed-indirect modes, the new page value is provided by an immediate operand in the
instruction. In indexed-indirect variations of CALL, a pointer specifies memory locations where the new
page value and the address of the called subroutine are stored. Using indirect addressing for both the new
page value and the address within the page allows values calculated at run time rather than immediate
values that must be known at the time of assembly.
The RTC instruction terminates subroutines invoked by a CALL instruction. RTC unstacks the PPAGE
value and the return address and refills the queue. Execution resumes with the next instruction after the
CALL.
Chapter 19 Module Mapping Control (MMCV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
562 Freescale Semiconductor
During the execution of an RTC instruction, the CPU:
Pulls the old PPAGE value from the stack
Pulls the 16-bit return address from the stack and loads it into the PC
Writes the old PPAGE value into the PPAGE register
Refills the queue and resumes execution at the return address
This sequence is uninterruptable; an RTC can be executed from anywhere in memory, even from a different
page of extended memory in the expansion window.
The CALL and RTC instructions behave like JSR and RTS, except they use more execution cycles.
Therefore, routinely substituting CALL/RTC for JSR/RTS is not recommended. JSR and RTS can be used
to access subroutines that are on the same page in expanded memory. However, a subroutine in expanded
memory that can be called from other pages must be terminated with an RTC. And the RTC unstacks a
PPAGE value. So any access to the subroutine, even from the same page, must use a CALL instruction so
that the correct PPAGE value is in the stack.
19.4.3.2 Extended Address (XAB19:14) and ECS Signal Functionality
If the EMK bit in the MODE register is set (see MEBI block description chapter) the PIX5:0 values will
be output on XAB19:14 respectively (port K bits 5:0) when the system is addressing within the physical
program page window address space (0x8000–0xBFFF) and is in an expanded mode. When addressing
anywhere else within the physical address space (outside of the paging space), the XAB19:14 signals will
be assigned a constant value based upon the physical address space selected. In addition, the active-low
emulation chip select signal, ECS, will likewise function based upon the assigned memory allocation. In
the cases of 48K byte and 64K byte allocated physical FLASH/ROM space, the operation of the ECS
signal will additionally depend upon the state of the ROMHM bit (see Section 19.3.2.4, “Miscellaneous
System Control Register (MISC)”) in the MISC register. Table 19-18,Table 19-19,Table 19-20, and
Table 19-21 summarize the functionality of these signals based upon the allocated memory configuration.
Again, this signal information is only available externally when the EMK bit is set and the system is in an
expanded mode.
Table 19-18. 0K Byte Physical FLASH/ROM Allocated
Address Space Page Window Access ROMHM ECS XAB19:14
0x0000–0x3FFF N/A N/A 1 0x3D
0x4000–0x7FFF N/A N/A 1 0x3E
0x8000–0xBFFF N/A N/A 0 PIX[5:0]
0xC000–0xFFFF N/A N/A 0 0x3F
Table 19-19. 16K Byte Physical FLASH/ROM Allocated
Address Space Page Window Access ROMHM ECS XAB19:14
0x0000–0x3FFF N/A N/A 1 0x3D
0x4000–0x7FFF N/A N/A 1 0x3E
0x8000–0xBFFF N/A N/A 1 PIX[5:0]
0xC000–0xFFFF N/A N/A 0 0x3F
Chapter 19 Module Mapping Control (MMCV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 563
Table 19-20. 48K Byte Physical FLASH/ROM Allocated
Address Space Page Window Access ROMHM ECS XAB19:14
0x0000–0x3FFF N/A N/A 1 0x3D
0x4000–0x7FFF N/A 0 0 0x3E
N/A 1 1
0x8000–0xBFFF External N/A 1 PIX[5:0]
Internal N/A 0
0xC000–0xFFFF N/A N/A 0 0x3F
Table 19-21. 64K Byte Physical FLASH/ROM Allocated
Address Space Page Window Access ROMHM ECS XAB19:14
0x0000–0x3FFF N/A 0 0 0x3D
N/A 1 1
0x4000–0x7FFF N/A 0 0 0x3E
N/A 1 1
0x8000–0xBFFF External N/A 1 PIX[5:0]
Internal N/A 0
0xC000–0xFFFF N/A N/A 0 0x3F
Chapter 19 Module Mapping Control (MMCV4) Block Description
MC9S12KG128 Data Sheet, Rev. 1.16
564 Freescale Semiconductor
A graphical example of a memory paging for a system configured as 1M byte on-chip FLASH/ROM with
64K allocated physical space is given in Figure 19-12.
Figure 19-12. Memory Paging Example: 1M Byte On-Chip FLASH/ROM, 64K Allocation
These 16K FLASH/ROM pages accessible from 0x0000 to 0x7FFF if selected
by the ROMHM bit in the MISC register.
NORMAL
SINGLE CHIP
ONE 16K FLASH/ROM PAGE ACCESSIBLE AT A TIME
(SELECTED BY PPAGE = 0 TO 63)
0x0000
0x8000
0xFF00
0xFFFF
0x4000
0xC000
59
62
63
60 61 62 630123
61
16K FLASH
(UNPAGED)
16K FLASH
(UNPAGED)
16K FLASH
(PAGED)
16K FLASH
(UNPAGED)
VECTORS
Appendix A Electrical Characteristics
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 565
Appendix A
Electrical Characteristics
A.1 General
NOTE
The electrical characteristics given in this section are preliminary and
should be used as a guide only. Values cannot be guaranteed by Freescale
and are subject to change without notice.
This supplement contains the most accurate electrical information for the MC9S12KG128 microcontroller
available at the time of publication. The information should be considered PRELIMINARY and is subject
to change.
This introduction is intended to give an overview on several common topics like power supply, current
injection, etc.
A.1.1 Parameter Classification
The electrical parameters shown in this supplement are guaranteed by various methods. To give the
customer a better understanding the following classification is used and the parameters are tagged
accordingly in the tables where appropriate.
NOTE
This classification is shown in the column labeled “C” in the parameter
tables where appropriate.
P: Those parameters are guaranteed during production testing on each individual device.
C: Those parameters are achieved by the design characterization by measuring a statistically relevant
sample size across process variations. They are regularly verified by production monitors.
T: Those parameters are achieved by design characterization on a small sample size from typical devices.
All values shown in the typical column are within this category.
D: Those parameters are derived mainly from simulations.
A.1.2 Power Supply
The MC9S12KG128 utilizes several pins to supply power to the I/O ports, A/D converter, oscillator, PLL
and internal logic.
The VDDA, VSSA pair supplies the A/D converter.
The VDDX, VSSX pair supplies the I/O pins.
The VDDR, VSSR pair supplies the internal voltage regulator.
VDD1, VSS1, VDD2 and VSS2 are the supply pins for the digital logic.
VDDPLL, VSSPLL supply the oscillator and the PLL.
Appendix A Electrical Characteristics
MC9S12KG128 Data Sheet, Rev. 1.16
566 Freescale Semiconductor
VSS1 and VSS2 are internally connected by metal.
VDD1 and VDD2 are internally connected by metal.
VDDA, VDDX, VDDR as well as VSSA, VSSX, VSSR are connected by anti-parallel diodes for
ESD protection.
NOTE
In the following context VDD5 is used for either VDDA, VDDR and
VDDX; VSS5 is used for either VSSA, VSSR and VSSX unless otherwise
noted. IDD5 denotes the sum of the currents flowing into the VDDA,
VDDX and VDDR pins. VDD is used for VDD1, VDD2 and VDDPLL,
VSS is used for VSS1, VSS2 and VSSPLL. IDD is used for the sum of the
currents flowing into VDD1 and VDD2.
A.1.3 Pins
There are four groups of functional pins.
A.1.3.1 3.3V/5V I/O Pins
Those I/O pins have a nominal level of 3.3V or 5V depending on the application operating point. This
group of pins is comprised of all port I/O pins, the analog inputs, BKGD pin and the RESET inputs.The
internal structure of all those pins is identical, however some of the functionality may be disabled. E.g. for
the analog inputs the output drivers, pull-up and pull-down resistors are disabled permanently.
A.1.3.2 Analog Reference
This group of pins is comprised of the VRH and VRL pins.
A.1.3.3 Oscillator
The pins EXTAL, XTAL dedicated to the oscillator have a nominal 2.5V level. They are supplied by
VDDPLL.
A.1.3.4 PLL
The pin XFC dedicated to the oscillator have a nominal 2.5V level. It is supplied by VDDPLL.
A.1.3.5 TEST
This pin is used for production testing only.
A.1.4 Current Injection
Power supply must maintain regulation within operating VDD5 or VDD range during instantaneous and
operating maximum current conditions. If positive injection current (Vin >V
DD5) is greater than IDD5, the
injection current may flow out of VDD5 and could result in external power supply going out of regulation.
Appendix A Electrical Characteristics
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 567
Insure external VDD5 load will shunt current greater than maximum injection current. This will be the
greatest risk when the MCU is not consuming power; e.g., if no system clock is present, or if clock rate is
very low which would reduce overall power consumption.
A.1.5 Absolute Maximum Ratings
Absolute maximum ratings are stress ratings only. A functional operation under or outside those maxima
is not guaranteed. Stress beyond those limits may affect the reliability or cause permanent damage of the
device.
This device contains circuitry protecting against damage due to high static voltage or electrical fields;
however, it is advised that normal precautions be taken to avoid application of any voltages higher than
maximum-rated voltages to this high-impedance circuit. Reliability of operation is enhanced if unused
inputs are tied to an appropriate logic voltage level (e.g., either VSS5 or VDD5).
Table A-1. Absolute Maximum Ratings
Num Rating Symbol Min Max Unit
1 I/O, Regulator and Analog Supply Voltage VDD5 –0.3 6.5 V
2 Internal Logic Supply Voltage1
1The device contains an internal voltage regulator to generate the logic and PLL supply out of the I/O supply. The absolute
maximum ratings apply when the device is powered from an external source.
VDD –0.3 3.0 V
3 PLL Supply Voltage 1VDDPLL –0.3 3.0 V
4 Voltage difference VDDX to VDDR and VDDA VDDX –0.3 0.3 V
5 Voltage difference VSSX to VSSR and VSSA VSSX –0.3 0.3 V
6 Digital I/O Input Voltage VIN –0.3 6.5 V
7 Analog Reference VRH, VRL –0.3 6.5 V
8 XFC, EXTAL, XTAL inputs VILV –0.3 3.0 V
9 TEST input VTEST –0.3 10.0 V
10 Instantaneous Maximum Current
Single pin limit for all digital I/O pins 2
2All digital I/O pins are internally clamped to VSSX and VDDX, VSSR and VDDR or VSSA and VDDA.
ID–25 +25 mA
11 Instantaneous Maximum Current
Single pin limit for XFC, EXTAL, XTAL3
3These pins are internally clamped to VSSPLL and VDDPLL
IDL –25 +25 mA
12 Instantaneous Maximum Current
Single pin limit for TEST4
4This pin is clamped low to VSSR, but not clamped high. This pin must be tied low in applications.
IDT –0.25 0 mA
13 Operating Temperature Range (packaged) TA–40 125 °C
14 Operating Temperature Range (junction) TJ –40 140 °C
15 Storage Temperature Range Tstg –65 155 °C
Appendix A Electrical Characteristics
MC9S12KG128 Data Sheet, Rev. 1.16
568 Freescale Semiconductor
A.1.6 ESD Protection and Latch-up Immunity
All ESD testing is in conformity with CDF-AEC-Q100 Stress test qualification for Automotive Grade
Integrated Circuits. During the device qualification ESD stresses were performed for the Human Body
Model (HBM), the Machine Model (MM) and the Charge Device Model.
A device will be defined as a failure if after exposure to ESD pulses the device no longer meets the device
specification. Complete DC parametric and functional testing is performed per the applicable device
specification at room temperature followed by hot temperature, unless specified otherwise in the device
specification.
Table A-2. ESD and Latch-up Test Conditions
Model Description Symbol Value Unit
Human Body Series Resistance R1 1500 Ohm
Storage Capacitance C 100 pF
Number of Pulse per pin
Positive
Negative
3
3
Machine Series Resistance R1 0 Ohm
Storage Capacitance C 200 pF
Number of Pulse per pin
Positive
Negative
3
3
Latch-up Minimum input voltage limit –2.5 V
Maximum input voltage limit 7.5 V
Table A-3. ESD and Latch-Up Protection Characteristics
Num C Rating Symbol Min Max Unit
1 C Human Body Model (HBM) VHBM 2000 V
2 C Machine Model (MM) VMM 200 V
3 C Charge Device Model (CDM) VCDM 500 V
4 C Latch-up Current at 125°C
Positive
Negative
ILAT +100
–100
mA
5 C Latch-up Current at 27°C
Positive
Negative
ILAT +200
–200
mA
Appendix A Electrical Characteristics
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 569
A.1.7 Operating Conditions
This chapter describes the operating conditions of the device. Unless otherwise noted those conditions
apply to all the following data.
NOTE
Instead of specifying ambient temperature all parameters are specified for
the more meaningful silicon junction temperature. For power dissipation
calculations refer to Section A.1.8, “Power Dissipation and Thermal
Characteristics”.
Table A-4. Operating Conditions
Rating Symbol Min Typ Max Unit
I/O, Regulator and Analog Supply Voltage VDD5 3.15 3.3/5 5.5 V
Internal Logic Supply Voltage1
1The device contains an internal voltage regulator to generate the logic and PLL supply out of the I/O supply. The absolute
maximum ratings apply when this regulator is disabled and the device is powered from an external source.
VDD 2.35 2.5 2.75 V
PLL Supply Voltage 1VDDPLL 2.35 2.5 2.75 V
Voltage Difference VDDX to VDDA VDDX –0.1 0 0.1 V
Voltage Difference VSSX to VSSR and VSSA VSSX –0.1 0 0.1 V
Oscillator fosc 0.5 16 MHz
Bus Frequency fbus 0.5 25 MHz
MC9S12KG128C
Operating Junction Temperature Range TJ–40 100 °C
Operating Ambient Temperature Range 2
2Please refer to Section A.1.8, “Power Dissipation and Thermal Characteristics” for more details about the relation between
ambient temperature TA and device junction temperature TJ.
TA–40 27 85 °C
MC9S12KG128V
Operating Junction Temperature Range TJ–40 120 °C
Operating Ambient Temperature Range 2TA–40 27 105 °C
MC9S12KG128M
Operating Junction Temperature Range TJ–40 140 °C
Operating Ambient Temperature Range 2TA–40 27 125 °C
Appendix A Electrical Characteristics
MC9S12KG128 Data Sheet, Rev. 1.16
570 Freescale Semiconductor
A.1.8 Power Dissipation and Thermal Characteristics
Power dissipation and thermal characteristics are closely related. The user must assure that the maximum
operating junction temperature is not exceeded. The average chip-junction temperature (TJ) in °C can be
obtained from:
The total power dissipation can be calculated from:
Two cases with internal voltage regulator enabled and disabled must be considered:
1. Internal Voltage Regulator disabled
PIO is the sum of all output currents on I/O ports associated with VDDX and VDDR.
For RDSON is valid:
respectively
2. Internal voltage regulator enabled
IDDR is the current shown in Table A-8 and not the overall current flowing into VDDR, which
additionally contains the current flowing into the external loads with output high.
PIO is the sum of all output currents on I/O ports associated with VDDX and VDDR.
TJTAPDΘJA
()+=
TJJunction Temperature, [°C]=
TAAmbient Temperature, [°C]=
PDTotal Chip Power Dissipation, [W]=
ΘJA Package Thermal Resistance, [°C/W]=
PDPINT PIO
+=
PINT Chip Internal Power Dissipation, [W]=
PINT IDD VDD
IDDPLL VDDPLL
IDDA
+V
DDA
+=
PIO RDSON
i
IIOi2
=
RDSON VOL
IOL
------------ for outputs driven low;=
RDSON VDD5 VOH
IOH
------------------------------------ for outputs driven high;=
PINT IDDR VDDR
IDDA VDDA
+=
PIO RDSON
i
IIOi2
=
Appendix A Electrical Characteristics
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 571
Table A-5. Thermal Package Characteristics1
1The values for thermal resistance are achieved by package simulations
Num C Rating Symbol Min Typ Max Unit
1 T Thermal Resistance LQFP112, single sided PCB2
2PC Board according to EIA/JEDEC Standard 51-2
θJA ——54
oC/W
2 T Thermal Resistance LQFP112, double sided PCB
with 2 internal planes3
3PC Board according to EIA/JEDEC Standard 51-7
θJA ——41
oC/W
3 T Thermal Resistance QFP 80, single sided PCB θJA ——51
oC/W
4 T Thermal Resistance QFP 80, double sided PCB with
2 internal planes θJA ——41
oC/W
Appendix A Electrical Characteristics
MC9S12KG128 Data Sheet, Rev. 1.16
572 Freescale Semiconductor
A.1.9 I/O Characteristics
This section describes the characteristics of all 3.3V/5V I/O pins. All parameters are not always applicable,
e.g., not all pins feature pull up/down resistances.
Table A-6. 5V I/O Characteristics
Conditions are shown in Table A-4 unless otherwise noted
Num C Rating Symbol Min Typ Max Unit
1 P Input High Voltage VIH 0.65*VDD5 —V
DD5 + 0.3 V
2 P Input Low Voltage VIL VSS5 - 0.3 0.35*VDD5 V
3 C Input Hysteresis VHYS 250 mV
4 P Input Leakage Current (pins in high impedance
input mode)
Vin = VDD5 or VSS5
Iin –2.5 2.5 µA
5 P Output High Voltage (pins in output mode)
Partial Drive IOH = –2.0mA
Full Drive IOH = –10.0mA
VOH VDD5 – 0.8 V
6 P Output Low Voltage (pins in output mode)
Partial Drive IOL = +2.0mA
Full Drive IOL = +10.0mA
VOL 0.8 V
7 P Internal Pull Up Device Current, tested at VIL Max. IPUL –130 µA
8 P Internal Pull Up Device Current, tested at VIH Min. IPUH 10 µA
9 P Internal Pull Down Device Current, tested at VIH Min. IPDH 130 µA
10 P Internal Pull Down Device Current, tested at VIL Max. IPDL 10 µA
11 D Input Capacitance Cin —7—pF
12 T Injection current1
Single Pin limit
Total Device Limit. Sum of all injected currents
1Refer to Section A.1.4, “Current Injection”, for more details
IICS
IICP
–2.5
–25
2.5
25
mA
13 P Port H, J, P Interrupt Input Pulse filtered2
2Parameter only applies in STOP or Pseudo STOP mode.
tpign —— 3µs
14 P Port H, J, P Interrupt Input Pulse passed2tpval 10 µs
Appendix A Electrical Characteristics
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 573
Table A-7. 3.3V I/O Characteristics
Conditions are shown in Table A-4 unless otherwise noted
Num C Rating Symbol Min Typ Max Unit
1 P Input High Voltage VIH 0.65*VDD5 —V
DD5 + 0.3 V
2 P Input Low Voltage VIL VSS5 - 0.3 0.35*VDD5 V
3 C Input Hysteresis VHYS 250 mV
4 P Input Leakage Current (pins in high impedance
input mode)
Vin = VDD5 or VSS5
Iin –1 1 µA
5 P Output High Voltage (pins in output mode)
Partial Drive IOH = –0.75mA
Full Drive IOH = –4.0mA
VOH VDD5 – 0.4 V
6 P Output Low Voltage (pins in output mode)
Partial Drive IOL = +0.9mA
Full Drive IOL = +4.75mA
VOL 0.4 V
7 P Internal Pull Up Device Current, tested at VIL Max. IPUL –60 µA
8 P Internal Pull Up Device Current, tested at VIH Min. IPUH –6 µA
9 P Internal Pull Down Device Current, tested at VIH Min. IPDH ——60µA
10 P Internal Pull Down Device Current, tested at VIL Max. IPDL 6—µA
11 D Input Capacitance Cin —7—pF
12 T Injection current1
Single Pin limit
Total Device Limit. Sum of all injected currents
1Refer to Section A.1.4, “Current Injection”, for more details
IICS
IICP
–2.5
–25
2.5
25
mA
13 P Port P, J Interrupt Input Pulse filtered2
2Parameter only applies in STOP or Pseudo STOP mode.
tPULSE —— 3µs
14 P Port P, J Interrupt Input Pulse passed2tPULSE 10 µs
Appendix A Electrical Characteristics
MC9S12KG128 Data Sheet, Rev. 1.16
574 Freescale Semiconductor
A.1.10 Supply Currents
This section describes the current consumption characteristics of the device as well as the conditions for
the measurements.
19.4.3.3 Measurement Conditions
All measurements are without output loads. Unless otherwise noted the currents are measured in single
chip mode, internal voltage regulator enabled and at 25MHz bus frequency using a 4MHz oscillator.
19.4.3.4 Additional Remarks
In expanded modes the currents flowing in the system are highly dependent on the load at the address, data
and control signals as well as on the duty cycle of those signals. No generally applicable numbers can be
given. A very good estimate is to take the single chip currents and add the currents due to the external loads.
Appendix A Electrical Characteristics
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 575
Table A-8. Supply Current Characteristics
Conditions are shown in Table A-4 unless otherwise noted
Num Rating Symbol Min Typ Max Unit
1 Run supply currents
Single Chip, Internal regulator enabled IDD5 ——65
mA
2 Wait Supply current All modules enabled
only RTI enabled1
1PLL off
IDDW
40
5
mA
3 Pseudo Stop Current (RTI and COP enabled)1,2
–40°C
27°C
70°C
85°C
"C" Temp Option 100°C
105°C
"V" Temp Option 120°C
125°C
"M" Temp Option 140°C
IDDPS
90
130
155
180
250
295
470
520
1000
350
1200
2400
5000
µA
4 Pseudo Stop Current (RTI and COP disabled)1,2
–40°C
27°C
70°C
85°C
"C" Temp Option 100°C
105°C
"V" Temp Option 120°C
125°C
"M" Temp Option 140°C
IDDPS
40
80
105
130
200
245
420
470
800
200
1000
2000
5000
µA
5 Stop Current2
–40°C
27°C
70°C
85°C
"C" Temp Option 100°C
105°C
"V" Temp Option 120°C
125°C
"M" Temp Option 140°C
2All those low power dissipation levels TJ = TA can be assumed.
IDDS
20
60
85
110
180
225
400
450
600
100
800
1800
5000
µA
Appendix A Electrical Characteristics
MC9S12KG128 Data Sheet, Rev. 1.16
576 Freescale Semiconductor
A.2 Voltage Regulator
This section describes the characteristics of the on chip voltage regulator.
Table A-9. VREG_3V3 — Operating Conditions
Num C Characteristic Symbol Min Typical Max Unit
1 P Input Voltages VVDDR,A 3.15 5.5 V
2 P Output Voltage Core
Full Performance Mode VDD 2.35 2.5 2.75 V
3 P Output Voltage PLL
Full Performance Mode VDDPLL 2.35 2.5 2.75 V
4 P Low Voltage Interrupt1
Assert Level
Deassert Level
1Monitors VDDA, active only in Full Performance Mode. Indicates I/O & ADC performance degradation due to low supply voltage.
VLVIA
VLVID
4.0
4.15 4.37
4.52 4.66
4.77 V
V
5 P Low Voltage Reset2
Assert Level
Deassert Level
2Monitors VDD, active only in Full Performance Mode. VLVRA and VPORD must overlap
VLVRA
VLVRD
2.25
2.55 V
V
6 C Power-on Reset3
Assert Level
Deassert Level
3Monitors VDD. Active in all modes.
The electrical characteristics given in this section are preliminary and
should be used as a guide only. Values in this section cannot be guaranteed
by Freescale and are subject to change without notice.
VPORA
VPORD
0.97
-—
2.05 V
V
Appendix A Electrical Characteristics
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 577
A.3 Chip Power-up and LVI/LVR Graphical Explanation
Voltage regulator sub modules LVI (low voltage interrupt), POR (power-on reset), and LVR (low voltage
reset) handle chip power-up or drops of the supply voltage. Their function is described in Figure A-1.
Figure A-1. Voltage Regulator — Chip Power-up and Voltage Drops (not scaled)
VLVID
VLVIA
VLVRD
VLVRA
VPORD
LVI
POR
LVR
t
VVDDA
VDD
LVI Enabled LVI Disabled due to LVR
Appendix A Electrical Characteristics
MC9S12KG128 Data Sheet, Rev. 1.16
578 Freescale Semiconductor
A.4 Output Loads
A.4.1 Resistive Loads
The on-chip voltage regulator is intended to supply the internal logic and oscillator circuits allows no
external DC loads.
A.4.2 Capacitive Loads
The capacitive loads are specified in Table A-10. Ceramic capacitors with X7R dielectricum are required.
Table A-10. Voltage Regulator — Capacitive Loads
Num Characteristic Symbol Min Typical Max Unit
1 VDD external capacitive load CDDext 200 440 12000 nF
2 VDDPLL external capacitive load CDDPLLext 90 220 5000 nF
Appendix A Electrical Characteristics
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 579
A.5 ATD Characteristics
This section describes the characteristics of the analog to digital converter.
A.5.1 ATD Operating Characteristics
The Table A-11 shows conditions under which the ATD operates.
The following constraints exist to obtain full-scale, full range results:
VSSA VRL VIN VRH VDDA.This constraint exists since the sample buffer amplifier can not
drive beyond the power supply levels that it ties to. If the input level goes outside of this range it will
effectively be clipped.
Table A-11. 5V ATD Operating Characteristics
Conditions are shown in Table A-4 unless otherwise noted
Num C Rating Symbol Min Typ Max Unit
1 D Reference Potential Low
High VRL
VRH VSSA
VDDA/2
VDDA/2
VDDA V
V
2 C Differential Reference Voltage1
1Full accuracy is not guaranteed when differential voltage is less than 4.75V
VRH-VRL 4.75 5.0 5.25 V
3 D ATD Clock Frequency fATDCLK 0.5 2.0 MHz
4 D ATD 10-Bit Conversion Period Clock Cycles2
Conv, Time at 2.0MHz ATD Clock fATDCLK
Conv, Time at 4.0MHz3 ATD Clock fATDCLK
2The minimum time assumes a final sample period of 2 ATD clocks cycles while the maximum time assumes a final sample
period of 16 ATD clocks.
3Reduced accuracy see Table A-14 and Table A-15.
NCONV10
TCONV10
TCONV10
14
7
3.5
28
14
7
Cycles
µs
µs
5 D ATD 8-Bit Conversion Period Clock Cycles1
Conv, Time at 2.0MHz ATD Clock fATDCLK
NCONV8
TCONV8
12
6
26
13 Cycles
µs
6 D Stop Recovery Time (VDDA=5.0 Volts) tSR ——20µs
7 P Reference Supply current (two ATD modules) IREF 0.750 mA
8 P Reference Supply current (one ATD module) IREF 0.375 mA
Appendix A Electrical Characteristics
MC9S12KG128 Data Sheet, Rev. 1.16
580 Freescale Semiconductor
A.5.2 Factors Influencing Accuracy
Three factors — source resistance, source capacitance and current injection — have an influence on the
accuracy of the ATD.
A.5.2.1 Source Resistance
Due to the input pin leakage current as specified in Table A-6 and Table A-7 in conjunction with the source
resistance there will be a voltage drop from the signal source to the ATD input. The maximum source
resistance RS specifies results in an error of less than 1/2 LSB (2.5mV) at the maximum leakage current.
If device or operating conditions are less than worst case or leakage-induced error is acceptable, larger
values of source resistance are allowed.
A.5.2.2 Source Capacitance
When sampling an additional internal capacitor is switched to the input. This can cause a voltage drop due
to charge sharing with the external and the pin capacitance. For a maximum sampling error of the input
voltage 1LSB, then the external filter capacitor, Cf 1024 * (CINS–CINN).
Table A-12. 3.3V ATD Operating Characteristics
Conditions are shown in Table A-4 unless otherwise noted; Supply Voltage 3.3V-10% <= VDDA <= 3.3V+10%
Num C Rating Symbol Min Typ Max Unit
1 D Reference Potential Low
High VRL
VRH
VSSA
VDDA/2
VDDA/2
VDDA
V
V
2 C Differential Reference Voltage VRH–VRL 3.0 3.3 3.6 V
3 D ATD Clock Frequency fATDCLK 0.5 2.0 MHz
4 D ATD 10-Bit Conversion Period Clock Cycles1
Conv, Time at 2.0MHz ATD Clock fATDCLK
Conv, Time at 4.0MHz2 ATD Clock fATDCLK
1The minimum time assumes a final sample period of 2 ATD clocks cycles while the maximum time assumes a final sample
period of 16 ATD clocks.
2Reduced accuracy see Table A-14 and Table A-15.
NCONV10
TCONV10
TCONV10
14
7
3.5
28
14
7
Cycles
µs
µs
5 D ATD 8-Bit Conversion Period Clock Cycles1
Conv, Time at 2.0MHz ATD Clock fATDCLK
NCONV8
TCONV8
12
6
26
13 Cycles
µs
6 D Recovery Time (VDDA=3.3 Volts) tREC ——20µs
7 P Reference Supply current (two ATD modules) IREF 0.500 mA
8 P Reference Supply current (one ATD module) IREF 0.250 mA
Appendix A Electrical Characteristics
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 581
A.5.2.3 Current Injection
There are two cases to consider.
1. A current is injected into the channel being converted. The channel being stressed has conversion
values of $3FF ($FF in 8-bit mode) for analog inputs greater than VRH and $000 for values less
than VRL unless the current is higher than specified as disruptive conditions.
2. Current is injected into pins in the neighborhood of the channel being converted. A portion of this
current is picked up by the channel (coupling ratio K), This additional current impacts the accuracy
of the conversion depending on the source resistance.
The additional input voltage error on the converted channel can be calculated as VERR =K*R
S*
IINJ, with IINJ being the sum of the currents injected into the two pins adjacent to the converted
channel.
A.5.3 ATD Accuracy
Table A-14 and Table A-15 specify the ATD conversion performance excluding any errors due to current
injection, input capacitance and source resistance.
Table A-13. ATD Electrical Characteristics
Conditions are shown in Table A-4 unless otherwise noted
Num Rating Symbol Min Typ Max Unit
1 Max input Source Resistance RS—— 1K
2 Total Input Capacitance Non Sampling
Sampling CINN
CINS
10
22
pF
3 Disruptive Analog Input Current INA –2.5 2.5 mA
4 Coupling Ratio positive current injection Kp——10
-4 A/A
5 Coupling Ratio negative current injection Kn——10
-2 A/A
Table A-14. 5V ATD Conversion Performance
Conditions are shown in Table A-4 unless otherwise noted
VREF = VRH - VRL = 5.12V. Resulting to one 8 bit count = 20mV and one 10 bit count = 5m. VfATDCLK = 2.0MHz
Num C Rating Symbol Min Typ Max Unit
1 P 10-Bit Resolution LSB 5 mV
2 P 10-Bit Differential Nonlinearity DNL –1 1 Counts
3 P 10-Bit Integral Nonlinearity INL –2.5 ±1.5 2.5 Counts
4 P 10-Bit Absolute Error1
1These values include quantization error which is inherently 1/2 count for any A/D converter.
AE –3 ±2.0 3 Counts
5 C 10-Bit Absolute Error at fATDCLK= 4MHz AE ±7.0 Counts
6 P 8-Bit Resolution LSB 20 mV
7 P 8-Bit Differential Nonlinearity DNL –0.5 0.5 Counts
8 P 8-Bit Integral Nonlinearity INL –1.0 ±0.5 1.0 Counts
9 P 8-Bit Absolute Error1AE –1.5 ±1.0 1.5 Counts
Appendix A Electrical Characteristics
MC9S12KG128 Data Sheet, Rev. 1.16
582 Freescale Semiconductor
For the following definitions see also Figure A-2.
Differential Non-Linearity (DNL) is defined as the difference between two adjacent switching steps.
The Integral Non-Linearity (INL) is defined as the sum of all DNLs:
Table A-15. 3.3V ATD Conversion Performance
Conditions are shown in Table A-4 unless otherwise noted
VREF = VRH - VRL = 3.328V. Resulting to one 8 bit count = 13mV and one 10 bit count = 3.25mV. fATDCLK = 2.0MHz
Num C Rating Symbol Min Typ Max Unit
1 P 10-Bit Resolution LSB 3.25 mV
2 P 10-Bit Differential Nonlinearity DNL –1.5 1.5 Counts
3 P 10-Bit Integral Nonlinearity INL –3.5 ±1.5 3.5 Counts
4 P 10-Bit Absolute Error1
1These values include the quantization error which is inherently 1/2 count for any A/D converter.
AE –5 ±2.5 5 Counts
5 C 10-Bit Absolute Error at fATDCLK= 4MHz AE ±7.0 Counts
6 P 8-Bit Resolution LSB 13 mV
7 P 8-Bit Differential Nonlinearity DNL –0.5 Counts
8 P 8-Bit Integral Nonlinearity INL –1.5 ±0.1 1.5 Counts
9 P 8-Bit Absolute Error1AE –2.0 ±1.5 2.0 Counts
DNL i() ViVi1
1LSB
---------------------------1=
INL n() DNL i()
i1=
n
VnV0
1LSB
---------------------n==
Appendix A Electrical Characteristics
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 583
Figure A-2. ATD Accuracy Definitions
NOTE
Figure A-2 shows only definitions, for specification values refer to
Table A-14 and Table A-15.
1
5Vin
mV
10 15 20 25 30 35 40 5085 5090 5095 5100 5105 5110 5115 51205065 5070 5075 50805060
0
3
2
5
4
7
6
50
$3F7
$3F9
$3F8
$3FB
$3FA
$3FD
$3FC
$3FE
$3FF
$3F4
$3F6
$3F5
8
9
1
2
$FF
$FE
$FD
$3F3
10-Bit Resolution
8-Bit Resolution
Ideal Transfer Curve
10-Bit Transfer Curve
8-Bit Transfer Curve
5055
10-Bit Absolute Error Boundary
8-Bit Absolute Error Boundary
LSB
Vi-1 Vi
DNL
Appendix A Electrical Characteristics
MC9S12KG128 Data Sheet, Rev. 1.16
584 Freescale Semiconductor
A.6 NVM, Flash and EEPROM
NOTE
Unless otherwise noted the abbreviation NVM (Non Volatile Memory) is
used for both Flash and EEPROM.
A.6.1 NVM Timing
The time base for all NVM program or erase operations is derived from the oscillator. A minimum
oscillator frequency fNVMOSC is required for performing program or erase operations. The NVM modules
do not have any means to monitor the frequency and will not prevent program or erase operation at
frequencies above or below the specified minimum. Attempting to program or erase the NVM modules at
a lower frequency a full program or erase transition is not assured.
The Flash and EEPROM program and erase operations are timed using a clock derived from the oscillator
using the FCLKDIV and ECLKDIV registers respectively. The frequency of this clock must be set within
the limits specified as fNVMOP
.
The minimum program and erase times shown in Table A-16 are calculated for maximum fNVMOP and
maximum fbus. The maximum times are calculated for minimum fNVMOP and a fbus of 2MHz.
A.6.1.1 Single Word Programming
The programming time for single word programming is dependant on the bus frequency as a well as on the
frequency fNVMOP and can be calculated according to the following formula.
A.6.1.2 Row Programming
Flash programming where up to 64 words in a row can be programmed consecutively by keeping the
command pipeline filled. The time to program a consecutive word can be calculated as:
The time to program a whole row is:
Row programming is more than 2 times faster than single word programming.
tswpgm 91
fNVMOP
-------------------------
25 1
fbus
------------
+=
tbwpgm 41
fNVMOP
-------------------------
91
fbus
------------
+=
tbrpgm tswpgm 63 tbwpgm
+=
Appendix A Electrical Characteristics
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 585
A.6.1.3 Sector Erase
Erasing a 1024 byte Flash sector or a 4 byte EEPROM sector takes:
The setup time can be ignored for this operation.
A.6.1.4 Mass Erase
Erasing a NVM block takes:
The setup time can be ignored for this operation.
A.6.1.5 Blank Check
The time it takes to perform a blank check on the Flash or EEPROM is dependant on the location of the
first non-blank word starting at relative address zero. It takes one bus cycle per word to verify plus a setup
of the command.
Table A-16. NVM Timing Characteristics
Conditions are shown in Table A-4 unless otherwise noted
Num C Rating Symbol Min Typ Max Unit
1 D External Oscillator Clock fNVMOSC 0.5 50 1
1Restrictions for oscillator in crystal mode apply!
MHz
2 D Bus frequency for Programming or Erase Operations fNVMBUS 1 MHz
3 D Operating Frequency fNVMOP 150 200 kHz
4 P Single Word Programming Time tswpgm 46 2
2Minimum Programming times are achieved under maximum NVM operating frequency fNVMOP and maximum bus frequency
fbus.
74.5 3
3Maximum Erase and Programming times are achieved under particular combinations of fNVMOP and bus frequency fbus. Refer
to formula in Section A.6.1.1, “Single Word Programming” and Section A.6.1.4, “Mass Erase” for guidance.
µs
5 D Flash Burst Programming consecutive word 4
4Burst Programming operations are not applicable to EEPROM
tbwpgm 20.4 2—31
3µs
6 D Flash Burst Programming Time for 64 Words 4tbrpgm 1331.2 2 2027.5 3µs
7 P Sector Erase Time tera 20 5
5Minimum Erase times are achieved under maximum NVM operating frequency fNVMOP
.
26.7 3ms
8 P Mass Erase Time tmass 100 5 133 3ms
9 D Blank Check Time Flash per block tcheck 11 6
6Minimum time, if first word in the array is not blank
65546 7
7Maximum time to complete check on an erased block
tcyc
10 D Blank Check Time EEPROM per block tcheck 11 6 20587tcyc
tera 4000 1
fNVMOP
-------------------------
tmass 20000 1
fNVMOP
-------------------------
tcheck location tcyc 10 tcyc
+
Appendix A Electrical Characteristics
MC9S12KG128 Data Sheet, Rev. 1.16
586 Freescale Semiconductor
A.6.2 NVM Reliability
The reliability of the NVM blocks is guaranteed by stress test during qualification, constant process
monitors and burn-in to screen early life failures.
The failure rates for data retention and program/erase cycling are specified at the operating conditions
noted.
The program/erase cycle count on the sector is incremented every time a sector or mass erase event is
executed.
NOTE
All values shown in Table A-17 are target values and subject to further
extensive characterization.
Table A-17. NVM Reliability Characteristics1
1TJavg will not exeed 85°C considering a typical temperature profile over the lifetime of a consumer, industrial or automotive
application.
Conditions are shown in Table A-4 unless otherwise noted
Num C Rating Symbol Min Typ Max Unit
1 C Data retention after 10,000 program/erase cycles at
an average junction temperature of TJavg 85°CtNVMRET 15 1002
2Typical data retention values are based on intrinsic capability of the technology measured at high temperature and de-rated to
25°C using the Arrhenius equation. For additional information on how Freescale defines Typical Data Retention, please refer
to Engineering Bulletin EB618.
Years
2 C Data retention with <100 program/erase cycles at an
average junction temperature TJavg 85°C20 1002
3 C Flash Number of program/erase cycles
(–40°C TJ 0°C) nFLPE 10,000 Cycles
(0°C TJ 140°C) 10,000 100,0003
3Spec table quotes typical endurance evaluated at 25°C for this product family, typical endurance at various temperature can
be estimated using the graph below. For additional information on how Freescale defines Typical Endurance, please refer to
Engineering Bulletin EB619.
4 C EEPROM number of Program/Erase cycles
(–40°C TJ 0°C) nEEPE 10,000 Cycles
(0°C < TJ140°C) 100,000 300,0003 Cycles
Appendix A Electrical Characteristics
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 587
A.7 Reset, Oscillator and PLL
This section summarizes the electrical characteristics of the various startup scenarios for Oscillator and
Phase-Locked-Loop (PLL).
A.7.1 Startup
Table A-18 summarizes several startup characteristics explained in this section. Detailed description of the
startup behavior can be found in the Clock and Reset Generator (CRG) Block User Guide.
A.7.1.1 POR
The release level VPORR and the assert level VPORA are derived from the VDD Supply. They are also valid
if the device is powered externally. After releasing the POR reset the oscillator and the clock quality check
are started. If after a time tCQOUT no valid oscillation is detected, the MCU will start using the internal self
clock. The fastest startup time possible is given by nuposc.
A.7.1.2 SRAM Data Retention
Provided an appropriate external reset signal is applied to the MCU, preventing the CPU from executing
code when VDD5 is out of specification limits, the SRAM contents integrity is guaranteed if after the reset
the PORF bit in the CRG Flags Register has not been set.
A.7.1.3 External Reset
When external reset is asserted for a time greater than PWRSTL the CRG module generates an internal
reset, and the CPU starts fetching the reset vector without doing a clock quality check, if there was an
oscillation before reset.
A.7.1.4 Stop Recovery
Out of STOP the controller can be woken up by an external interrupt. A clock quality check as after POR
is performed before releasing the clocks to the system.
Table A-18. Startup Characteristics
Conditions are shown in Table A-4 unless otherwise noted
Num C Rating Symbol Min Typ Max Unit
1 T POR release level VPORR 2.07 V
2 T POR assert level VPORA 0.97 V
3 D Reset input pulse width, minimum input time PWRSTL 2—t
osc
4 D Startup from Reset nRST 192 196 nosc
5 D Interrupt pulse width, IRQ edge-sensitive mode PWIRQ 20 ns
6 D Wait recovery startup time tWRS 14 tcyc
Appendix A Electrical Characteristics
MC9S12KG128 Data Sheet, Rev. 1.16
588 Freescale Semiconductor
A.7.1.5 Pseudo Stop and Wait Recovery
The recovery from Pseudo STOP and Wait are essentially the same since the oscillator was not stopped in
both modes. The controller can be woken up by internal or external interrupts. After twrs the CPU starts
fetching the interrupt vector.
A.7.2 Oscillator
The device features an internal low-power loop controlled Pierce oscillator and a full swing Pierce
oscillator/external clock mode. The selection of loop controlled Pierce oscillator or full swing Pierce
oscillator/external clock depends on the XCLKS signal which is sampled during reset. Full swing Pierce
oscillator/external clock mode allows the input of a square wave. Before asserting the oscillator to the
internal system clocks the quality of the oscillation is checked for each start from either power-on, STOP
or oscillator fail. tCQOUT specifies the maximum time before switching to the internal self clock mode after
POR or STOP if a proper oscillation is not detected. The quality check also determines the minimum
oscillator start-up time tUPOSC. The device also features a clock monitor. A Clock Monitor Failure is
asserted if the frequency of the incoming clock signal is below the Assert Frequency fCMFA.
Table A-19. Oscillator Characteristics
Conditions are shown in Table A-4 unless otherwise noted
Num C Rating Symbol Min Typ Max Unit
1a C Crystal oscillator range (loop controlled Pierce) fOSC 4.0 16 MHz
1b C Crystal oscillator range (full swing Pierce) 1,2
1Depending on the crystal a damping series resistor might be necessary
2Only valid if full swing Pierce oscillator/external clock mode is selected
fOSC 0.5 40 MHz
2 P Startup Current iOSC 100 µA
3 C Oscillator start-up time (loop controlled Pierce) tUPOSC —3
3
3fOSC = 4MHz, C = 22pF.
504
4Maximum value is for extreme cases using high Q, low frequency crystals
ms
4 D Clock Quality check time-out tCQOUT 0.45 2.5 s
5 P Clock Monitor Failure Assert Frequency fCMFA 50 100 200 KHz
6 P External square wave input frequency fEXT 0.5 50 MHz
7 D External square wave pulse width low tEXTL 9.5 ns
8 D External square wave pulse width high tEXTH 9.5 ns
9 D External square wave rise time tEXTR —— 1 ns
10 D External square wave fall time tEXTF —— 1 ns
11 D Input Capacitance (EXTAL, XTAL pins) CIN —7pF
12 P EXTAL Pin Input High Voltage VIH,EXTAL 0.75*VDDPLL —— V
T EXTAL Pin Input High Voltage VIH,EXTAL ——V
DDPLL + 0.3 V
13 P EXTAL Pin Input Low Voltage VIL,EXTAL 0.25*VDDPLL V
T EXTAL Pin Input Low Voltage VIL,EXTAL VSSPLL – 0.3 V
14 C EXTAL Pin Input Hysteresis VHYS,EXTAL 250 mV
Appendix A Electrical Characteristics
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 589
A.7.3 Phase Locked Loop
The oscillator provides the reference clock for the PLL. The PLL´s Voltage Controlled Oscillator (VCO)
is also the system clock source in self clock mode.
A.7.3.1 XFC Component Selection
This section describes the selection of the XFC components to achieve a good filter characteristics.
Figure A-3. Basic PLL Functional Diagram
The following procedure can be used to calculate the resistance and capacitance values using typical values
for K1, f1 and ich from Table A-20.
The grey boxes show the calculation for fVCO = 50MHz and fref = 1MHz. E.g., these frequencies are used
for fOSC = 4MHz and a 25MHz bus clock.
The VCO Gain at the desired VCO frequency is approximated by:
The phase detector relationship is given by:
ich is the current in tracking mode.
The loop bandwidth fCshould be chosen to fulfill the Gardner’s stability criteria by at least a factor of 10,
typical values are 50. ζ = 0.9 ensures a good transient response.
And finally the frequency relationship is defined as
fosc 1
refdv+1 fref Phase
Detector
VCO
KV
1
synr+1
fvco
Loop Divider
KF
1
2
D
fcmp
Cs R
Cp
VDDPLL
XFC Pin
KVK1e
f1fvco
()
K11V
----------------------------
=100e
60 50()
100
----------------------
=
= -90.48MHz/V
KΦich
KV
==316.7Hz/
Appendix A Electrical Characteristics
MC9S12KG128 Data Sheet, Rev. 1.16
590 Freescale Semiconductor
With the above values the resistance can be calculated. The example is shown for a loop bandwidth
fC=10kHz:
The capacitance Cs can now be calculated as:
The capacitance Cp should be chosen in the range of:
A.7.3.2 Jitter Information
NOTE
This section is under construction
The basic functionality of the PLL is shown in Figure A-3. With each transition of the clock fcmp, the
deviation from the reference clock fref is measured and input voltage to the VCO is adjusted
accordingly.The adjustment is done continuously with no abrupt changes in the clock output frequency.
Noise, voltage, temperature and other factors cause slight variations in the control loop resulting in a clock
jitter. This jitter affects the real minimum and maximum clock periods as illustrated in Figure A-4.
Figure A-4. Jitter Definitions
nfVCO
fref
--------------- 2 synr 1+()== = 50
fC2ζfref
⋅⋅
πζ 1ζ2
++


-------------------------------------------1
10
------fCfref
410
------------- ζ0.9=();<<
fC < 25kHz
R2πnf
C
⋅⋅⋅
KΦ
-----------------------------==2*π*50*10kHz/(316.7Hz/)=9.9k=~10k
Cs2ζ2
πfCR⋅⋅
---------------------- 0.516
fCR
---------------ζ0.9=();== 5.19nF =~ 4.7nF
Cs20CpCs10≤≤ Cp = 470pF
2 3 N-1 N1
0
tnom
tmax1
tmin1
tmaxN
tminN
Appendix A Electrical Characteristics
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 591
The relative deviation of tnom is at its maximum for one clock period, and decreases towards zero for larger
number of clock periods (N).
Appendix A Electrical Characteristics
MC9S12KG128 Data Sheet, Rev. 1.16
592 Freescale Semiconductor
Defining the jitter as:
NOTE
From the evaluation data a formula for tmax= f(N), resp. tmin = f(N) should
be derived.
Assuming no long term drift of the reference clock, the following will hold
This is very important to notice with respect to timers, serial modules where a pre-scaler will eliminate the
effect of the jitter to a large extent.
Table A-20. PLL Characteristics
Conditions are shown in Table A-4 unless otherwise noted
Num C Rating Symbol Min Typ Max Unit
1 P Self Clock Mode frequency fSCM 1 5.5 MHz
2 D VCO locking range fVCO 8 50 MHz
3 D Lock Detector transition from Acquisition to Tracking
mode trk 3% 4%1
1% deviation from target frequency
4 D Lock Detection Lock 0% 1.5%1
5 D Un-Lock Detection unl 0.5% 2.5%1
6 D Lock Detector transition from Tracking to Acquisition
mode unt 6% 8%1
7 C PLLON Total Stabilization delay2
2fOSC = 4MHz, fBUS = 25MHz equivalent fVCO = 50MHz: REFDV = #$03, SYNR = #$018, Cs = 4.7nF, Cp = 470pF, Rs = 10K.
tstab 0.5 ms
8 D PLLON Acquisition mode stabilization delay2tacq 0.3 ms
9 D PLLON Tracking mode stabilization delay2tal 0.2 ms
10 D Fitting parameter VCO loop gain K1 –100 MHz/V
11 D Fitting parameter VCO loop frequency f1 60 MHz
12 D Charge pump current acquisition mode ich –38.5 µA
13 D Charge pump current tracking mode ich –l3.5 µA
14 C Jitter fit parameter 12j1 1.1 %
15 C Jitter fit parameter 22j2 0.13 %
JN() max 1 tmax N()
Nt
nom
-----------------------
1tmin N()
Nt
nom
-----------------------
,



=
JN()
N
lim 0=
Appendix A Electrical Characteristics
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 593
A.8 MSCAN
A.9 SPI
A.9.1 Master Mode
Figure A-5 and Figure A-6 illustrate the master mode timing. Timing values are shown in Table A-22.
Figure A-5. SPI Master Timing (CPHA = 0)
Table A-21. MSCAN Wake-up Pulse Characteristics
Conditions are shown in Table A-4 unless otherwise noted
Num C Rating Symbol Min Typ Max Unit
1 P MSCAN Wake-up dominant pulse filtered tWUP —— 2µs
2 P MSCAN Wake-up dominant pulse pass tWUP 5—µs
SCK
(OUTPUT)
SCK
(OUTPUT)
MISO
(INPUT)
MOSI
(OUTPUT)
SS1
(OUTPUT)
1
9
5 6
MSB IN2
BIT 6 . . . 1
LSB IN
MSB OUT2 LSB OUT
BIT 6 . . . 1
10
4
4
2
9
(CPOL = 0)
(CPOL = 1)
3
11
12
1. If configured as an output.
2. LSBF = 0. For LSBF = 1, bit order is LSB, bit 1, ..., bit 6, MSB.
Appendix A Electrical Characteristics
MC9S12KG128 Data Sheet, Rev. 1.16
594 Freescale Semiconductor
Figure A-6. SPI Master Timing (CPHA =1)
Table A-22. SPI Master Mode Timing Characteristics
Conditions are shown in Table A-4 unless otherwise noted, CLOAD = 200pF on all outputs
Num C Rating Symbol Min Typ Max Unit
1 P Operating Frequency fop DC 1/4f
bus
1 P SCK Period tsck 4 2048 tbus
2 D Enable Lead Time tlead 1/2—t
sck
3 D Enable Lag Time tlag 1/2— t
sck
4 D Clock (SCK) High or Low Time twsck tbus 30 1024 tbus ns
5 D Data Setup Time (Inputs) tsu 25 ns
6 D Data Hold Time (Inputs) thi 0—ns
9 D Data Valid (after SCK Edge) tv 25 ns
10 D Data Hold Time (Outputs) tho 0—ns
11 D Rise Time Inputs and Outputs tr 25 ns
12 D Fall Time Inputs and Outputs tf 25 ns
SCK
(OUTPUT)
SCK
(OUTPUT)
MISO
(INPUT)
MOSI
(OUTPUT)
1
5 6
MSB IN2
BIT 6 . . . 1
LSB IN
MASTER MSB OUT2 MASTER LSB OUT
BIT 6 . . . 1
4
4
9
11 12
10
PORT DATA
(CPOL = 0)
(CPOL = 1)
PORT DATA
SS1
(OUTPUT)
212 11 3
1. If configured as output
2. LSBF = 0. For LSBF = 1, bit order is LSB, bit 1, ..., bit 6, MSB.
Appendix A Electrical Characteristics
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 595
A.9.2 Slave Mode
Figure A-7 and Figure A-8 illustrate the slave mode timing. Timing values are shown in Table A-23.
Figure A-7. SPI Slave Timing (CPHA = 0)
Figure A-8. SPI Slave Timing (CPHA =1)
SCK
(INPUT)
SCK
(INPUT)
MOSI
(INPUT)
MISO
(OUTPUT)
SS
(INPUT)
1
9
5 6
MSB IN
BIT 6 . . . 1
LSB IN
MSB OUT SLAVE LSB OUT
BIT 6 . . . 1
10
4
4
2
7
(CPOL = 0)
(CPOL = 1)
3
12
NOTE: Not defined but normally MSB of character just received.
SLAVE
12
11
10
SEE
11
NOTE
8
SCK
(INPUT)
SCK
(INPUT)
MOSI
(INPUT)
MISO
(OUTPUT)
1
5 6
MSB IN
BIT 6 . . . 1
LSB IN
MSB OUT SLAVE LSB OUT
BIT 6 . . . 1
4
4
9
11 12
10
SEE
(CPOL = 0)
(CPOL = 1)
SS
(INPUT)
212 11 3
NOTE: Not defined but normally LSB of character just received.
SLAVE
NOTE
7
8
Appendix A Electrical Characteristics
MC9S12KG128 Data Sheet, Rev. 1.16
596 Freescale Semiconductor
A.10 External Bus Timing
A timing diagram of the external multiplexed-bus is illustrated in Figure A-9 with the actual timing values
shown on table Table A-24. All major bus signals are included in the diagram. While both a data write and
data read cycle are shown, only one or the other would occur on a particular bus cycle.
A.10.1 General Muxed Bus Timing
The expanded bus timings are highly dependent on the load conditions. The timing parameters shown
assume a balanced load across all outputs.
Table A-23. SPI Slave Mode Timing Characteristics
Conditions are shown in Table A-4 unless otherwise noted, CLOAD = 200pF on all outputs
Num C Rating Symbol Min Typ Max Unit
1 P Operating Frequency fop DC 1/4f
bus
1 P SCK Period tsck 4 2048 tbus
2 D Enable Lead Time tlead 1—t
cyc
3 D Enable Lag Time tlag 1—t
cyc
4 D Clock (SCK) High or Low Time twsck tcyc 30 ns
5 D Data Setup Time (Inputs) tsu 25 ns
6 D Data Hold Time (Inputs) thi 25 ns
7 D Slave Access Time ta—— 1t
cyc
8 D Slave MISO Disable Time tdis —— 1t
cyc
9 D Data Valid (after SCK Edge) tv 25 ns
10 D Data Hold Time (Outputs) tho 0—ns
11 D Rise Time Inputs and Outputs tr 25 ns
12 D Fall Time Inputs and Outputs tf 25 ns
Appendix A Electrical Characteristics
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 597
Figure A-9. General External Bus Timing
Addr/Data
(read)
Addr/Data
(write)
addr data
data
5 10 11
8
166
ECLK
1, 2
3 4
addr data
data
12
159
7
14 13
ECS
2120 22 23
Non-Multiplexed
17 19
LSTRB
29
NOACC
32
PIPO0
PIPO1, PE6,5
35
18
27 28
30
33 36
31
34
R/W
24 26
25
Addresses
PE4
PA, PB
PA, PB
PK5:0
PK7
PE2
PE3
PE7
Appendix A Electrical Characteristics
MC9S12KG128 Data Sheet, Rev. 1.16
598 Freescale Semiconductor
Table A-24. Expanded Bus Timing Characteristics
Conditions are shown in Table A-4 unless otherwise noted, CLOAD = 50pF
Num C Rating Symbol Min Typ Max Unit
1 P Frequency of operation (E-clock) fo0 25.0 MHz
2 P Cycle time tcyc 40 ns
3 D Pulse width, E low PWEL 17 ns
4 D Pulse width, E high1
1Affected by clock stretch: add N x tcyc where N=0,1,2 or 3, depending on the number of clock stretches.
PWEH 17 ns
5 D Address delay time tAD —— 8ns
6 D Address valid time to E rise (PWEL–tAD)t
AV 11 ns
7 D Muxed address hold time tMAH 2—ns
8 D Address hold to data valid tAHDS 7—ns
9 D Data hold to address tDHA 2—ns
10 D Read data setup time tDSR 13 ns
11 D Read data hold time tDHR 0—ns
12 D Write data delay time tDDW —— 7ns
13 D Write data hold time tDHW 2—ns
14 D Write data setup time1 (PWEH–tDDW)t
DSW 10 ns
15 D Address access time1(tcyc–tAD–tDSR)t
ACCA 19 ns
16 D E high access time1(PWEH–tDSR)t
ACCE 4—ns
17 D Non-multiplexed address delay time tNAD —— 7ns
18 D Non-muxed address valid to E rise (PWEL–tNAD)t
NAV 10 ns
19 D Non-multiplexed address hold time tNAH 2—ns
20 D Chip select delay time tCSD 16 ns
21 D Chip select access time1 (tcyc–tCSD–tDSR)t
ACCS 11 ns
22 D Chip select hold time tCSH 2—ns
23 D Chip select negated time tCSN 8—ns
24 D Read/write delay time tRWD —— 7ns
25 D Read/write valid time to E rise (PWEL–tRWD)t
RWV 10 ns
26 D Read/write hold time tRWH 2—ns
27 D Low strobe delay time tLSD —— 7ns
28 D Low strobe valid time to E rise (PWEL–tLSD)t
LSV 10 ns
29 D Low strobe hold time tLSH 2—ns
30 D NOACC strobe delay time tNOD —— 7ns
31 D NOACC valid time to E rise (PWEL–tLSD)t
NOV 10 ns
32 D NOACC hold time tNOH 2—ns
33 D PIPO0 delay time tP0D 2—7ns
34 D PIPO0 valid time to E rise (PWEL–tP0D)t
P0V 10 ns
35 D PIPO1 delay time1(PWEH-tP1V)t
P1D 2—7ns
36 D PIPO1 valid time to E fall tP1V 10 ns
Appendix B Recommended PCB Layout
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 599
Appendix B
Recommended PCB Layout
Figure B-1. Recommended PCB Layout for 112LQFP
C5
C4
C1
C6
C3
C2
C10
C9
R1
VDDX
VSSX
VDDR
VSSR
VDD1
VSS1
VDD2
VSS2
VDDPLL
VSSPLL
VDDA
VSSA
VREGEN
C7
C8
Q1
Appendix B Recommended PCB Layout
MC9S12KG128 Data Sheet, Rev. 1.16
600 Freescale Semiconductor
Figure B-2. Recommended PCB Layout for 80QFP
C5
C4
C3
C2
C10
C9
R1
C6
C1
VDD1
VSS1
VSS2
VDD2
VSSR
VDDR
VSSPLL
VDDPLL
VDDA
VSSA
VSSX
VREGEN
VDDX
C7
C8
Q1 VSSPLL
Appendix B Recommended PCB Layout
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 601
The PCB must be carefully laid out to ensure proper operation of the voltage regulator as well as of the
MCU itself{Statement}. The following rules must be observed:
Every supply pair must be decoupled by a ceramic capacitor connected as near as possible to the
corresponding pins (C1 - C6).
Central point of the ground star should be the VSSR pin.
Use low ohmic low inductance connections between VSS1, VSS2 and VSSR.
VSSPLL must be directly connected to VSSR.
Keep traces of VSSPLL, EXTAL and XTAL as short as possible and occupied board area for C7,
C8 and Q1 as small as possible.
Do not place other signals or supplies underneath area occupied by C7, C8 and Q1 and the
connection area to the MCU.
Central power input should be fed in at the VDDA/VSSA pins.
Table B-1. Recommended Components
Component Purpose Type Value
C1 VDD1 filter cap ceramic X7R 400nF
C2 VDD2 filter cap (80
QFP only) ceramic X7R 400nF
C3 VDDA filter cap ceramic X7R 100nF
C4 VDDR filter cap X7R/tantalum >=100nF
C5 VDDPLL filter cap ceramic X7R 200nF
C6 VDDX filter cap X7R/tantalum >=100nF
C7 OSC load cap
C8 OSC load cap
C9 PLL loop filter cap
See PLL specification chapterC10 PLL loop filter cap
R1 PLL loop filter res
Q1 Quartz
Appendix C Package Information
MC9S12KG128 Data Sheet, Rev. 1.16
602 Freescale Semiconductor
Appendix C
Package Information
This section provides the physical dimensions of the MC9S12KG128 packages.
Appendix C Package Information
MC9S12KG128 Data Sheet, Rev. 1.16
Freescale Semiconductor 603
C.1 112-Pin LQFP Package
Figure C-1. 112-Pin LQFP Mechanical Dimensions (Case no. 987)
DIM
AMIN MAX
20.000 BSC
MILLIMETERS
A1 10.000 BSC
B20.000 BSC
B1 10.000 BSC
C--- 1.600
C1 0.050 0.150
C2 1.350 1.450
D0.270 0.370
E0.450 0.750
F0.270 0.330
G0.650 BSC
J0.090 0.170
K0.500 REF
P0.325 BSC
R1 0.100 0.200
R2 0.100 0.200
S22.000 BSC
S1 11.000 BSC
V22.000 BSC
V1 11.000 BSC
Y0.250 REF
Z1.000 REF
AA 0.090 0.160
θ
θ
θ
θ11 °
11 °13 °
7°
13 °
VIEW Y
L-M0.20 NT
4X 4X 28 TIPS
PIN 1
IDENT
1
112 85
84
28 57
29 56
BV
V1
B1
A1
S1
A
S
VIEW AB
0.10
3
CC2
θ
2θ
0.050
SEATING
PLANE
GAGE PLANE
1θ
θ
VIEW AB
C1
(Z)
(Y) E
(K)
R2
R1 0.25
J1
VIEW Y
J1
P
G
108X
4X
SECTION J1-J1
BASE
ROTATED 90 COUNTERCLOCKWISE
°
METAL
JAA
F
DL-M
M
0.13 NT
1
2
3
C
L
L-M0.20 NT
L
N
M
T
T
112X
X
X=L, M OR N
R
R
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. DIMENSIONS IN MILLIMETERS.
3. DATUMS L, M AND N TO BE DETERMINED AT
SEATING PLANE, DATUM T.
4. DIMENSIONS S AND V TO BE DETERMINED AT
SEATING PLANE, DATUM T.
5. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION. ALLOWABLE
PROTRUSION IS 0.25 PER SIDE. DIMENSIONS
A AND B INCLUDE MOLD MISMATCH.
6. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL NOT CAUSE THE D
DIMENSION TO EXCEED 0.46.
8°
3°
0°
Appendix C Package Information
MC9S12KG128 Data Sheet, Rev. 1.16
604 Freescale Semiconductor
C.2 80-Pin QFP Package
Figure C-2. 80-Pin QFP Mechanical Dimensions (Case no. 841B)
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DATUM PLANE -H- IS LOCATED AT BOTTOM OF
LEAD AND IS COINCIDENT WITH THE
LEAD WHERE THE LEAD EXITS THE PLASTIC
BODY AT THE BOTTOM OF THE PARTING LINE.
4. DATUMS -A-, -B- AND -D- TO BE
DETERMINED AT DATUM PLANE -H-.
5. DIMENSIONS S AND V TO BE DETERMINED
AT SEATING PLANE -C-.
6. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION. ALLOWABLE
PROTRUSION IS 0.25 PER SIDE. DIMENSIONS
A AND B DO INCLUDE MOLD MISMATCH
AND ARE DETERMINED AT DATUM PLANE -H-.
7. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.08 TOTAL IN
EXCESS OF THE D DIMENSION AT MAXIMUM
MATERIAL CONDITION. DAMBAR CANNOT
BE LOCATED ON THE LOWER RADIUS OR
THE FOOT.
SECTION B-B
61 60
DETAIL A
L
41
40
80
-A-
L
-D-
A
S
A-B
M
0.20 D S
H
0.05 A-B
S
120
21
-B-
BV
J
F
N
D
VIEW ROTATED 90 °
DETAIL A
B
BP
-A-,-B-,-D-
E
H
GM
MDETAIL C
SEATING
PLANE
-C-
CDATUM
PLANE
0.10
-H-
DATUM
PLANE -H-
U
T
R
Q
K
WX
DETAIL C
DIM MIN MAX
MILLIMETERS
A13.90 14.10
B13.90 14.10
C2.15 2.45
D0.22 0.38
E2.00 2.40
F0.22 0.33
G0.65 BSC
H--- 0.25
J0.13 0.23
K0.65 0.95
L12.35 REF
M510
N0.13 0.17
P0.325 BSC
Q07
R0.13 0.30
S16.95 17.45
T0.13 ---
U0 ---
V16.95 17.45
W0.35 0.45
X1.6 REF
°°
°°
°
S
A-B
M
0.20 D S
C
S
A-B
M
0.20 D S
H
0.05 D
S
A-B
M
0.20 D S
C
S
A-B
M
0.20 D S
C
How to Reach Us:
Home Page:
www.freescale.com
USA/Europe or Locations Not Listed:
Freescale Semiconductor
Technical Information Center, CH370
1300 N. Alma School Road
Chandler, Arizona 85224
1-800-521-6274 or 480-768-2130
Europe, Middle East, and Africa:
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
Japan:
Freescale Semiconductor Japan Ltd.
Technical Information Center
3-20-1, Minami-Azabu, Minato-ku
Tokyo 106-0047, Japan
0120-191014 or +81-3-3440-3569
Asia/Pacific:
Freescale Semiconductor Hong Kong Ltd.
Technical Information Center
2 Dai King Street
Tai Po Industrial Estate
Tai Po, N.T., Hong Kong
852-26668334
For Literature Requests Only:
Freescale Semiconductor Literature Distribution Center
P.O. Box 5405
Denver, Colorado 80217
1-800-441-2447 or 303-675-2140
Fax: 303-675-2150
Freescale™ and the Freescale logo are trademarks of Freescale
Semiconductor, Inc. All other product or service names are the property
of their respective owners. The ARM POWERED logo is a registered
trademark of ARM Limited. ARM7TDMI-S is a trademark of ARM Limited.
Java and all other Java-based marks are trademarks or registered
trademarks of Sun Microsystems, Inc. in the U.S. and other countries.
The Bluetooth trademarks are owned by their proprietor and used by
Freescale Semiconductor, Inc. under license.
© Freescale Semiconductor, Inc. 2005. All rights reserved.
MC9S12KG128V1
Rev. Rev. 1.16
06/2010
Information in this document is provided solely to enable system and
software implementers to use Freescale Semiconductor products. There are
no express or implied copyright licenses granted hereunder to design or
fabricate any integrated circuits or integrated circuits based on the
information in this document.
Freescale Semiconductorreservestheright tomakechanges without further
notice to any products herein. Freescale Semiconductor makes no warranty,
representation or guarantee regarding the suitability of its products for any
particular purpose, nor does Freescale Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation consequential or
incidental damages. “Typical” parameters that may be provided in Freescale
Semiconductor data sheets and/or specifications can and do vary in different
applications and actual performance may vary over time. All operating
parameters, including “Typicals”, must be validated for each customer
application by customer’s technical experts. Freescale Semiconductor does
not convey any license under its patent rights nor the rights of others.
FreescaleSemiconductorproductsarenot designed,intended, orauthorized
for use as components in systems intended for surgical implant into the body,
or other applications intended to support or sustain life, or for any other
applicationinwhich the failureof the FreescaleSemiconductor productcould
create a situation where personal injury or death may occur. Should Buyer
purchase or use Freescale Semiconductor products for any such unintended
or unauthorized application, Buyer shall indemnify and hold Freescale
Semiconductor and its officers, employees, subsidiaries, affiliates, and
distributors harmless against all claims, costs, damages, and expenses, and
reasonable attorney fees arising out of, directly or indirectly, any claim of
personal injury or death associated with such unintended or unauthorized
use, even if such claim alleges that Freescale Semiconductor was negligent
regarding the design or manufacture of the part.