A Datasheet SaBLE-x-R2TM Bluetooth(R) Smart (BLE) Module Version 1.5 SaBLE-x-R2 Datasheet REVISION HISTORY Version Date Notes Approver 1.0 1.1 20 June 2017 22 June 2017 Initial Release Updated Device Markings Section Josh Bablitch Josh Bablitch 1.2 1.3 6 July 2017 21 Aug 2017 Added Industry Canada Statement Added mFlexPIFA antenna information Josh Bablitch Bill Steinike 1.4 1.5 9 Nov 2017 22 Oct 2018 Updated Certification Section Updated Legal Statement, Label Info, & Added New Part Numbers Robert Gosewehr Robert Gosewehr Connectivity Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 330-0237-R1.5 2 The information in this document is subject to change without notice. (c) Copyright 2017-2018 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 SaBLE-x-R2 Datasheet CONTENTS 1 2 3 4 5 6 7 Description .........................................................................................................................................................4 Features ..............................................................................................................................................................4 Applications ........................................................................................................................................................4 Ordering Information .........................................................................................................................................5 Module Accessories ............................................................................................................................................6 Pin Descriptions ..................................................................................................................................................8 Electrical Specifications ................................................................................................................................... 10 7.1 Absolute Maximum Ratings..................................................................................................................... 10 7.2 Recommended Operating Conditions ..................................................................................................... 10 7.3 General Characteristics............................................................................................................................ 10 7.4 DC Characteristics .................................................................................................................................... 11 7.5 General Power Consumption .................................................................................................................. 12 7.6 RF Characteristics - TX ............................................................................................................................. 12 7.7 RF Characteristics - RX 1 Mbps (BLE) ...................................................................................................... 13 7.8 RF Characteristics - RX 2 Mbps (BLE5) .................................................................................................... 13 7.9 RF Characteristics - RX 125-kbps Coded (BLE5) ...................................................................................... 14 7.10 RF Characteristics - RX 500-kbps Coded (BLE5) ...................................................................................... 14 7.11 Wakeup Timing ........................................................................................................................................ 15 8 Soldering Recommendations........................................................................................................................... 17 9 Cleaning ........................................................................................................................................................... 17 10 Optical Inspection ........................................................................................................................................ 17 11 Rework ......................................................................................................................................................... 18 12 Shipping, Handling, and Storage ................................................................................................................. 18 12.1 Shipping ................................................................................................................................................... 18 12.2 Handling................................................................................................................................................... 18 12.3 Moisture Sensitivity Level (MSL) ............................................................................................................. 18 12.4 Storage..................................................................................................................................................... 18 12.5 Repeating Reflow Soldering .................................................................................................................... 18 13 Agency Certifications ................................................................................................................................... 19 14 Agency Statements ...................................................................................................................................... 19 14.1 Federal Communication Commission Interference Statement ............................................................... 19 14.2 Industry Canada Statements ................................................................................................................... 20 14.3 OEM Responsibilities to Comply with FCC and Industry Canada Regulations ........................................ 21 14.4 OEM Labeling Requirements for End-Product ........................................................................................ 22 14.5 OEM End Product User Manual Statements ........................................................................................... 22 15 Europe ......................................................................................................................................................... 23 16 Australia ....................................................................................................................................................... 23 17 Bluetooth SIG Qualification ......................................................................................................................... 24 18 Antenna Information ................................................................................................................................... 26 19 Mechanical Data .......................................................................................................................................... 33 20 PCB Footprint............................................................................................................................................... 34 21 Device Markings .......................................................................................................................................... 36 22 Contacting LSR ............................................................................................................................................. 38 Connectivity Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 330-0237-R1.5 3 The information in this document is subject to change without notice. (c) Copyright 2017-2018 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 SaBLE-x-R2 Datasheet 1 DESCRIPTION Laird is announcing a low-cost and low-power consumption module with all Bluetooth 5 Low Energy functionalities. The SaBLE-x-R2 module fully supports the single mode Bluetooth Low Energy operation and the output power can support class 2. The module provides the ability to either put your entire application into the integrated ARM Cortex M3 microcontroller. Need to get to market quickly? Not an expert in Bluetooth Low Energy? Need a custom antenna? Do you need help with your host board? LSR Design Services will be happy to develop custom hardware or software, or help integrate the design. Contact us at sales@lsr.com or call us at 262-375-4400. 2 FEATURES Built-in CC2640R2F Bluetooth 5 Low Energy System-On-Chip (SOC) 5x5 mm RHB package with 15 GPIOs 128 kB Flash/20 kB SRAM RF Output Power: +5 dBm RF Receive Sensitivity: -96 dBm Size: 11.6 mm x 17.9 mm x 2.4 mm Operating Voltage: 1.8V to 3.8V Operating Temperature: -40 to +85C 8.4 mA Transmit Mode (+5 dBm) 7.4 mA Receive Mode 1A Standby (SRAM/CPU retention and RTC running) with quick 100 s start up 200 nA Shutdown 61A/MHz Active CPU Current Drivers, Bluetooth Low Energy Controller, and bootloader in ROM Flexible peripheral set On board 32 KHz and 24 MHz Crystals Worldwide Acceptance: - FCC (USA), IC (Canada), - ETSI (Europe), Giteki (Japan), and - RCM (AU/NZ) BT SIG QD ID: 96853 REACH and RoHS compliant 3 APPLICATIONS Consumer electronics Mobile phone accessories Sports and fitness equipment HID applications Home and building automation, lighting control, alarm and security Electronic shelf labeling and proximity tags Connectivity Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 330-0237-R1.5 4 The information in this document is subject to change without notice. (c) Copyright 2017-2018 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 SaBLE-x-R2 Datasheet 4 ORDERING INFORMATION Table 1: Orderable model numbers Order Number 450-0177C Description SaBLE-x-R2 Module, PCB Trace Antenna (Cut Tape) 450-0177R 450-0178C SaBLE-x-R2 Module, PCB Trace Antenna (Tape & Reel) SaBLE-x-R2 Module, External Antenna Port (Cut Tape) 450-0178R 450-0184 SaBLE-x-R2 Module, External Antenna Port (Tape & Reel) SaBLE-x-R2 Evaluation Kit, PCB Trace Antenna 450-0185 450-0194C SaBLE-x-R2 Development Kit, PCB Trace Antenna SaBLE-x-R2 Module, Non-Ferrous Shield, PCB Trace Antenna (Cut Tape) 450-0194R 450-0195C SaBLE-x-R2 Module, Non-Ferrous Shield, PCB Trace Antenna (Tape & Reel) SaBLE-x-R2 Module, Non-Ferrous Shield, External Antenna Port (Cut Tape) 450-0195R SaBLE-x-R2 Module, Non-Ferrous Shield, External Antenna Port (Tape & Reel) Connectivity Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 330-0237-R1.5 5 The information in this document is subject to change without notice. (c) Copyright 2017-2018 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 SaBLE-x-R2 Datasheet 5 MODULE ACCESSORIES Table 2: Module accessories Order Number Connectivity Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 330-0237-R1.5 Description 001-0001 2.4 GHz Dipole Antenna with Reverse Polarity SMA Connector 080-0001 U.FL to Reverse Polarity SMA Bulkhead Cable 105 mm 001-0014 2.4 GHz FlexPIFA antenna 001-0015 2.4 GHz FlexNotch Antenna 6 The information in this document is subject to change without notice. (c) Copyright 2017-2018 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 SaBLE-x-R2 Datasheet Order Number 001-0030 Off Module Antenna (optional) Description 2.4 GHz Metal FlexPIFA Antenna w/U.FL Cable, 100mm VCC /Reset Band Pass Filter PCB Trace Antenna (optional) 32 kHz Crystal 2 15 2 Wire JTAG I/O CC2640R2F Bluetooth Low Energy (BLE) System-on-Chip (SOC) 24 MHz Crystal SaBLE-x-R2 Module Figure 1: SaBLE-x-R2 module block diagram Connectivity Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 330-0237-R1.5 7 The information in this document is subject to change without notice. (c) Copyright 2017-2018 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 SaBLE-x-R2 Datasheet 1 33 2 32 3 31 4 30 5 29 6 28 7 34 37 27 8 26 9 35 38 25 10 24 11 36 39 23 12 22 13 14 15 16 17 18 19 20 21 Figure 2: SaBLE-x-R2 module footprint (viewed from top) 6 PIN DESCRIPTIONS Table 3: SaBLE-x-R2 Pin Descriptions Module Pin 1 2 3 Name RF OUT GND GND I/O Type RF GND GND 4 5 NC NC - 6 7 /RESET JTAG_TCKC DI DI/DIO 8 JTAG_TMSC DIO Connectivity Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 330-0237-R1.5 Description Antenna, 50 OHMS Ground Ground No Connect (Do Not Connect) No Connect (Do Not Connect) Active Low Reset. 100 k Pull-up JTAG TCKC JTAG TMSC 8 The information in this document is subject to change without notice. (c) Copyright 2017-2018 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 SaBLE-x-R2 Datasheet Module Pin 9 Name NC I/O Type - Description No Connect (Do Not Connect) 10 11 NC VCC PI No Connect (Do Not Connect) Power Supply to Module 12 13 VCC DIO_5/JTAG_TDO PI DIO Power Supply to Module GPIO, JTAG_TDO, LED Driving Capability 14 15 DIO_6/JTAG_TDI DIO_4 DIO DIO GPIO, JTAG_TDI, LED Driving Capability GPIO, ULP Sensor Interface, LED Driving Capability 16 17 DIO_3 DIO_2 DIO DIO 18 DIO_1/BOOT_RX DIO 19 DIO_0/BOOT_TX DIO 20 21 22 23 24 25 26 27 DIO_7 DIO_8 GND DIO_10 DIO_9 NC NC NC DIO DIO GND DIO DIO - GPIO, ULP Sensor Interface, LED Driving Capability GPIO, ULP Sensor Interface, LED Driving Capability GPIO, ULP Sensor Interface, Bootloader RX (UART0) GPIO, ULP Sensor Interface, Bootloader TX (UART0) GPIO, Analog Input, ULP Sensor Interface GPIO, Analog Input, ULP Sensor Interface Ground GPIO, Analog Input, ULP Sensor Interface GPIO, Analog Input, ULP Sensor Interface No Connect (Do Not Connect) No Connect (Do Not Connect) No Connect (Do Not Connect) 28 29 NC DIO_11 DIO No Connect (Do Not Connect) GPIO, Analog Input, ULP Sensor Interface 30 31 DIO_12 DIO_13 DIO DIO GPIO, Analog Input, ULP Sensor Interface GPIO, Analog Input, ULP Sensor Interface 32 33 DIO_14 GND DIO GND GPIO, Analog Input, ULP Sensor Interface Ground 34-39 GND GND PI = Power Input GND = Ground DI = Digital Input DO = Digital Output DIO = Digital Input/Output Ground and Thermal Relief Pads AI = Analog Input RF = Bi-directional RF Port Note: See the Texas Instruments CC2640 datasheet and user guide for further details on the I/O. Connectivity Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 330-0237-R1.5 9 The information in this document is subject to change without notice. (c) Copyright 2017-2018 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 SaBLE-x-R2 Datasheet 7 ELECTRICAL SPECIFICATIONS 7.1 Absolute Maximum Ratings Table 4: Absolute maximum ratings Symbol Description Min Max Unit VCC Digital Input Supply Voltage -0.3 4.1 V Voltage on any digital pin -0.3 VCC+0.3, max 4.1 V Input RF level +5 dBm IMPORTANT! Do not exceed the absolute maximum ratings specified in Table 4 under any circumstances. Stressing the module beyond these limits may result in permanent damage to the module; this damage is not covered by the warranty. 7.2 Recommended Operating Conditions 7.2.1 Test Conditions: Ambient Temp = 25C Table 5: Recommended operating conditions Symbol VCC Min Typ 3.3 1.8 Max 3.8 Unit V 7.3 General Characteristics Table 6: General Characteristics Characteristic Model Name Product Description Dimension Operating temperature Storage temperature Humidity Description SaBLE-x-R2 Bluetooth Low Energy Wireless Module 11.63 mm x 17.86 mm x 2.4 mm (W*L*T) -40C to 85C -40C to 85C Operating Humidity: 10% to 95% Non-Condensing Storage Humidity: 5% to 95% Non-Condensing Weight 0.75 g 0.05 g Connectivity Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 330-0237-R1.5 10 The information in this document is subject to change without notice. (c) Copyright 2017-2018 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 SaBLE-x-R2 Datasheet 7.4 DC Characteristics Table 7: SaBLE-x-R2 module Bluetooth general DC characteristics Parameter Input low-to-high transition with hysteresis Test Conditions Transition from 0 to 1, TA= 25C, VCC=1.8V Input high-to-low transition with hysteresis Input hysteresis Transition from 1 to 0, TA= 25C, VCC=1.8V Difference between 0 to 1 and 1 to 0. 0.74 V 0.33 V Input low-to-high transition with hysteresis Input high-to-low transition with hysteresis Transition from 0 to 1, TA= 25C, VCC=3.8V Transition from 1 to 0, TA= 25C, VCC=3.8V 1.94 V 1.54 V Input hysteresis Logic-0 output voltage, 4 mA pins Logic-1 output voltage, 4 mA pins Logic-0 output voltage, 8 mA pins Logic-1 output voltage, 8 mA pins Logic-0 output voltage, 4 mA pins Logic-1 output voltage, 4 mA pins Logic-0 output voltage, 8 mA pins Logic-1 output voltage, 8 mA pins Input pullup current Difference between 0 to 1 and 1 to 0. Output load 4 mA, TA= 25C, VCC=1.8V Output load 4 mA, TA= 25C, VCC=1.8V Output load 8 mA, TA= 25C, VCC=1.8V Output load 8 mA, TA= 25C, VCC=1.8V Output load 4 mA, TA= 25C, VCC=3.0V Output load 4 mA, TA= 25C, VCC=3.0V Output load 8 mA, TA= 25C, VCC=3.0V Output load 8 mA, TA= 25C, VCC=3.0V Vpad=0V, TA= 25C, VCC=1.8V 0.40 0.26 1.54 0.21 1.58 0.33 2.72 0.28 2.68 72 V V V V V V V V V uA Input pulldown current Input pullup current Vpad=1.8V, TA= 25C, VCC=1.8V Vpad=0V, TA= 25C, VCC=3.8V 22 277 uA uA Input pulldown current Vpad=3.8V, TA= 25C, VCC=3.8V 113 uA Connectivity Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 330-0237-R1.5 Min 11 The information in this document is subject to change without notice. (c) Copyright 2017-2018 Laird. All Rights Reserved Typ 1.07 Max Unit V Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 SaBLE-x-R2 Datasheet 7.5 General Power Consumption 7.5.1 TA = 25C Table 8: SaBLE-x-R2 module Bluetooth TX and RX current consumption specifications Parameter Test Conditions Min Shutdown Standby 1 Standby 2 Idle No clocks running, no data retention With RTC, CPU, RAM, and partial register retention. XOSC_LF With Cache, RTC, CPU, RAM, and partial register retention. XOSC_LF Active Supply Systems and RAM powered. Core running CoreMark Radio RX Radio TX DC-DC Turned OFF +5 dBm output power Typical Average Current 1.8V 3.0V 3.3V 3.8V 200 12.7 13.6 12.8 9.0 Max Unit nA 1.2 uA 2.7 uA 550 uA 1.45 mA + 31 uA/MHz 12.9 8.4 13.0 7.9 mA 7.6 RF Characteristics - TX The following results are typical performance for the following data rates: 1 Mbps (BLE), 2 Mbps (BLE5), 125 kbps, and 500 kbps Coded (BLE5) Results measured on LSR SaBLE-x-R2 external antenna development board reference design with TA = 25C, LEDs disabled, DC-to-DC converter enabled, and measured at RF connector. Table 9: BLE TX RF characteristics Test Conditions Output Power CH 0 (2402 MHZ) CH 19 (2440 MHZ) 4.8 4.6 4.8 4.7 4.8 4.7 4.8 4.7 CH 39 (2480 MHZ) f < 1 GHz 4.3 4.3 4.3 4.4 Spurious Emission Conducted Measurement RF Frequency Range Min Typical 3.0V 3.3V Parameter f > 1 GHz Programmable in one-MHz steps Connectivity Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 330-0237-R1.5 1.8V 3.8V Max Unit dBm -43 dBm -46 dBm 2402 12 The information in this document is subject to change without notice. (c) Copyright 2017-2018 Laird. All Rights Reserved 2480 MHz Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 SaBLE-x-R2 Datasheet 7.7 RF Characteristics - RX 1 Mbps (BLE) Table 10: BLE TX RF characteristics Parameter Receiver Sensitivity DC to DC Disabled Receiver Sensitivity DC to DC Enabled Saturation Co-channel Rejection Frequency Error Tolerance Intermodulation 1.8V Typical 3.0V 3.3V 3.8V CH 0 (2402 MHZ) CH 19 (2440 MHZ) -95 -95 -95 -95 -95 -95 -95 -95 CH 39 (2480 MHZ) CH 0 (2402 MHZ) -95 -95 -95 -94 -95 -93 -95 -92 CH 19 (2440 MHZ) CH 39 (2480 MHZ) -95 -95 -94 -94 -93 -93 -92 -92 Test Conditions Min Wanted signal -67 dBm Unit dBm dBm 4 -6 BER < 0.1% Difference between the incoming carrier frequency and the internally-generated carrier frequency Minimum interferer level Max dBm dB -350 350 -34 kHz dBm 7.8 RF Characteristics - RX 2 Mbps (BLE5) Table 11: BLE TX RF characteristics Parameter Receiver Sensitivity DC to DC Disabled Receiver Sensitivity DC to DC Enabled Test Conditions BER < 0.1% Co-channel Rejection Wanted signal -67 dBm Intermodulation Min CH 0 (2402 MHZ) CH 19 (2440 MHZ) CH 39 (2480 MHZ) CH 0 (2402 MHZ) CH 19 (2440 MHZ) CH 39 (2480 MHZ) Saturation Frequency Error Tolerance Typical Difference between the incoming carrier frequency and the internally generated carrier frequency Minimum interferer level Connectivity Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 330-0237-R1.5 1.8V -91.5 -91.5 -91.5 -91.5 -91.5 -91.5 3.0V -91.5 -91.5 -91.5 -90 -90 -90 3.3V -91.5 -91.5 -91.5 -89.5 -89.5 -89.5 4 3.8V -91.5 -91.5 -91.5 -89 -89 -89 Max dBm dBm dBm -7 -300 13 The information in this document is subject to change without notice. (c) Copyright 2017-2018 Laird. All Rights Reserved dB 500 -45 Unit kHz dBm Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 SaBLE-x-R2 Datasheet 7.9 RF Characteristics - RX 125-kbps Coded (BLE5) Table 12: BLE TX RF characteristics Parameter Receiver Sensitivity DC to DC Disabled Receiver Sensitivity DC to DC Enabled 1.8V Typical 3.0V 3.3V 3.8V CH 0 (2402 MHZ) CH 19 (2440 MHZ) -102 -102 -102 -102 -102 -102 -102 -102 CH 39 (2480 MHZ) CH 0 (2402 MHZ) -102 -102 -102 -100 -102 -98 -102 -97 CH 19 (2440 MHZ) CH 39 (2480 MHZ) -102 -102 -100 -100 -98 -98 -97 -97 Test Conditions Min Max Unit dBm dBm Saturation BER < 0.1% 5 dBm Co-channel Rejection Wanted signal -79 dBm -3 dB Frequency Error Tolerance Difference between the incoming carrier frequency and the internally generated carrier frequency Intermodulation Minimum interferer level -260 310 -42 kHz dBm 7.10 RF Characteristics - RX 500-kbps Coded (BLE5) Table 13: BLE TX RF characteristics Parameter Receiver Sensitivity DC to DC Disabled Receiver Sensitivity DC to DC Enabled Saturation Co-channel Rejection Frequency Error Tolerance Intermodulation Test Conditions Min CH 0 (2402 MHZ) CH 19 (2440 MHZ) CH 39 (2480 MHZ) CH 0 (2402 MHZ) CH 19 (2440 MHZ) CH 39 (2480 MHZ) 1.8V -99.5 -99.5 -99.5 -99.5 -99.5 -99.5 Typical 3.0V 3.3V -99.5 -99.5 -99.5 -99.5 -99.5 -99.5 -98 -96 -98 -96 -98 -96 Connectivity Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 330-0237-R1.5 Max -240 dBm 14 The information in this document is subject to change without notice. (c) Copyright 2017-2018 Laird. All Rights Reserved dBm dB 240 -37 Unit dBm 5 -5 BER < 0.1% Wanted signal -79 dBm Difference between the incoming carrier frequency and the internally generated carrier frequency Minimum interferer level 3.8V -99.5 -99.5 -99.5 -95 -95 -95 kHz dBm Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 SaBLE-x-R2 Datasheet 7.11 Wakeup Timing 7.11.1 Shutdown Shutdown is similar to holding the device in reset with two exceptions: It latches the state of IO prior to shutting down. It consumes 0.1 uA, versus approximately 37 uA. Figure 3 shows the response time to wake up from shutdown by using a wake-up pin. The pin is configured to wake the device up on a negative edge. Once the device wakes, it drives an awake pin low: Figure 3: SaBLE-x-R2 module waking from shutdown timing diagram Figure 3 shows the module taking approximately 160 milliseconds to wake. Connectivity Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 330-0237-R1.5 15 The information in this document is subject to change without notice. (c) Copyright 2017-2018 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 SaBLE-x-R2 Datasheet 7.11.2 Standby Standby is a low power mode policy. When configured correctly in code the software goes into standby. Figure 4 shows the response time to wake up from standby using a wake up pin. The method is the same as described in the shutdown section: Figure 4: SaBLE-x-R2 module waking from standby timing diagram Figure 4 shows the module taking approximately 139 s to wake. Connectivity Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 330-0237-R1.5 16 The information in this document is subject to change without notice. (c) Copyright 2017-2018 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 SaBLE-x-R2 Datasheet 8 SOLDERING RECOMMENDATIONS 8.1 Recommended Reflow Profile for Lead Free Solder Figure 5: Recommended soldering profile Note: The quality of solder joints on the surface mount pads where they contact the host board should meet the appropriate IPC Specification. See IPC-A-610-D Acceptability of Electronic Assemblies, section 8.2.1 Bottom Only Terminations. 9 CLEANING In general, cleaning the populated modules is strongly discouraged. Residuals under the module cannot be easily removed with any cleaning process. Cleaning with water can lead to capillary effects where water is absorbed into the gap between the host board and the module. The combination of soldering flux residuals and encapsulated water could lead to short circuits between neighboring pads. Water could also damage any stickers or labels. Cleaning with alcohol or a similar organic solvent will likely flood soldering flux residuals into the RF shield, which is not accessible for post-washing inspection. The solvent could also damage any stickers or labels. Ultrasonic cleaning could damage the module permanently. 10 OPTICAL INSPECTION After soldering the module to the host board, consider optical inspection to check the following: Proper alignment and centering of the module over the pads. Proper solder joints on all pads. Excessive solder or contacts to neighboring pads, or vias. Connectivity Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 330-0237-R1.5 17 The information in this document is subject to change without notice. (c) Copyright 2017-2018 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 SaBLE-x-R2 Datasheet 11 REWORK The module can be unsoldered from the host board if the Moisture Sensitivity Level (MSL) requirements are met as described in this datasheet. Note: Never attempt a rework on the module itself, e.g. replacing individual components. Such actions will terminate warranty coverage. 12 SHIPPING, HANDLING, AND STORAGE 12.1 Shipping Bulk orders of the SaBLE-x-R2 modules are delivered in reels of 1,000. 12.2 Handling The SaBLE-x-R2 modules contain a highly sensitive electronic circuitry. Handling without proper ESD protection may damage the module permanently. 12.3 Moisture Sensitivity Level (MSL) Per J-STD-020, devices rated as MSL 4 and not stored in a sealed bag with desiccant pack should be baked prior to use. Devices are packaged in a Moisture Barrier Bag with a desiccant pack and Humidity Indicator Card (HIC). Devices that will be subjected to reflow should reference the HIC and J-STD-033 to determine if baking is required. If baking is required, refer to J-STD-033 for bake procedure. 12.4 Storage Per J-STD-033, the shelf life of devices in a Moisture Barrier Bag is 12 months at <40C and <90% room humidity (RH). Do not store in salty air or in an environment with a high concentration of corrosive gas, such as Cl2, H2S, NH3, SO2, or NOX. Do not store in direct sunlight. The product should not be subject to excessive mechanical shock. 12.5 Repeating Reflow Soldering Note: Only a single reflow soldering process is encouraged for host boards. Connectivity Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 330-0237-R1.5 18 The information in this document is subject to change without notice. (c) Copyright 2017-2018 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 SaBLE-x-R2 Datasheet 13 AGENCY CERTIFICATIONS FCC ID TFB-1005, FCC Part 15.247 IC ID 5969A-1005, RSS 247 CE Compliant to standards EN 60950-1, ETSI EN 300 328, ETSI EN 301 489-1, and ETSI 301 489-17 Giteki: Compliant to standard ARIB STD-T66 v3.7 201-170613 (PCB trace antenna) 201-170614 (External antenna) RCM: Compliant to standard AS/NZS 4268:2017 14 AGENCY STATEMENTS 14.1 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This portable transmitter with its antenna complies with FCC/IC RF exposure limits for general population/ uncontrolled exposure. FCC CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Connectivity Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 330-0237-R1.5 19 The information in this document is subject to change without notice. (c) Copyright 2017-2018 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 SaBLE-x-R2 Datasheet 14.2 Industry Canada Statements Radiation Exposure Statement: This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. This device has been designed to operate with the antenna(s) listed below, and having a maximum gain of 0 dBi (PCB Trace), 2.0 dBi (LSR 2.4 GHz Dipole), 2.0 dBi (LSR 2.4 GHz FlexPIFA), 2.0 dBi (LSR 2.4 GHz FlexNotch), and 2.0 (LSR 2.4 GHz mFlexPIFA). Antennas not included in this list or having a gain greater than 0 dB, 2.0 dBi, 2.0 dBi, 2.0 dBi, and 2.0 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. List of all Antennas Acceptable for use with the Transmitter On module PCB trace antenna. LSR 001-0001 center-fed 2.4 GHz dipole antenna and LSR 080-0001 U.FL to Reverse Polarity SMA connector cable. LSR 001-0014 2.4 GHz FlexPIFA antenna. LSR 001-0015 2.4 GHz FlexNotch antenna. LSR 001-0030 2.4 GHz Metal FlexPIFA (mFlexPIFA) antenna. Declaration d'exposition aux radiations: Cet equipement est conforme Canada limites d'exposition aux radiations dans un environnement non controle. Cet equipement doit etre installe et utilise a distance minimum de 20cm entre le radiateur et votre corps. Cet appareil est conforme aux normes d'Industrie Canada exempts de licence RSS (s). L'operation est soumise aux deux conditions suivantes: (1) cet appareil ne peut pas provoquer d'interferences et (2) cet appareil doit accepter toute interference, y compris les interferences qui peuvent causer un mauvais fonctionnement de l'appareil. Pour reduire le risque d'interference aux autres utilisateurs, le type d'antenne et son gain doiventetre choisis de maniere que la puissance isotrope rayonnee equivalente (PIRE) ne depasse pascelle permise pour une communication reussie. Cet appareil a ete concu pour fonctionner avec l'antenne (s) ci-dessous, et ayant un gain maximum de 0 dBi (PCB Trace), 2,0 dBi (LSR 2.4 GHz Dipole), 2,0 dBi (LSR 2.4 GHz FlexPIFA), 2,0 dBi (LSR 2.4 GHz FlexNotch), et 2,0 dBi (LSR 2.4 GHz mFlexPIFA). Antennes pas inclus dans cette liste ou presentant un gain superieur a 0 dBi, 2,0 dBi, 2,0 dBi, 2,0 dBi, et 2,0 dBi sont strictement interdites pour une utilisation avec cet appareil. L'impedance d'antenne requise est de 50 ohms. Liste de toutes les antennes acceptables pour une utilisation avec l'emetteur Le module d'antenne PCB trace. LSR 001-0001 centre-fed 2,4 GHz antenne dipole et LSR 080-0001 U.FL pour inverser cable connecteur SMA a polarite. Connectivity Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 330-0237-R1.5 20 The information in this document is subject to change without notice. (c) Copyright 2017-2018 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 SaBLE-x-R2 Datasheet LSR 001-0014 antenne FlexPIFA 2,4 GHz. LSR 001-0015 antenne FlexNotch 2,4 GHz. LSR 001-0030 antenne Metal FlexPIFA (mFlexPIFA) 2,4 GHz 14.3 OEM Responsibilities to Comply with FCC and Industry Canada Regulations The SaBLE-x-R2 module has been certified for integration into products only by OEM integrators under the following conditions: The antennas for this transmitter must not be co-located with any other transmitters except in accordance with FCC and Industry Canada multi-transmitter procedures. As long as the two conditions above are met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions cannot be met (for certain configurations or colocation with another transmitter), then the FCC and Industry Canada authorizations are no longer considered valid and the FCC ID and IC Certification Number cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC and Industry Canada authorization. Le module de SaBLE-x-R2a ete certifie pour l'integration dans des produits uniquement par des integrateurs OEM dans les conditions suivantes: Les antennes pour ce transmetteur ne doit pas etre co-localises avec les autres emetteurs sauf en conformite avec la FCC et Industrie Canada multi-emetteur procedures.. Tant que les deux conditions precitees sont reunies, les tests de transmetteurs supplementaires ne seront pas tenus. Toutefois, l'integrateur OEM est toujours responsable de tester leur produit final pour toutes les exigences de conformite supplementaires requis avec ce module installe (par exemple, les emissions appareil numerique, les exigences de peripheriques PC, etc.) NOTE IMPORTANTE: Dans le cas ou ces conditions ne peuvent etre satisfaites (pour certaines configurations ou de co-implantation avec un autre emetteur), puis la FCC et Industrie autorisations Canada ne sont plus consideres comme valides et l'ID de la FCC et IC numero de certification ne peut pas etre utilise sur la produit final. Dans ces circonstances, l'integrateur OEM sera charge de reevaluer le produit final (y compris l'emetteur) et l'obtention d'un distincte de la FCC et Industrie Canada l'autorisation. Connectivity Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 330-0237-R1.5 21 The information in this document is subject to change without notice. (c) Copyright 2017-2018 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 SaBLE-x-R2 Datasheet OEM Labeling Requirements for End-Product The SaBLE-x-R2 module is labeled with its own FCC ID and IC certification number. The FCC ID and IC certification numbers are not visible when the module is installed inside another device. As such, the end device into which the module is installed must display a label referring to the enclosed module. The end product must be labeled in a visible area with the following: Contains Transmitter Module FCC ID: TFB-1005 Contains Transmitter Module IC: 5969A-1005 or Contains FCC ID: TFB-1005 Contains IC: 5969A-1005 The OEM of the SaBLE-x-R2 module must only use the approved antenna(s) listed above, which have been certified with this module. Le module de SaBLE-x-R2 est etiquete avec son propre ID de la FCC et IC numero de certification. L'ID de la FCC et IC numeros de certification ne sont pas visibles lorsque le module est installe a l'interieur d'un autre appareil, comme par exemple le terminal dans lequel le module est installe doit afficher une etiquette faisant reference au module ci-joint. Le produit final doit etre etiquete dans un endroit visible par le suivant: Contient Module emetteur FCC ID: TFB-1005 Contient Module emetteur IC: 5969A-1005 ou Contient FCC ID: TFB-1005 Contient IC: 5969A-1005 Les OEM du module SaBLE-x-R2 ne doit utiliser l'antenne approuvee (s) ci-dessus, qui ont ete certifies avec ce module. 14.4 OEM End Product User Manual Statements The OEM integrator should not provide information to the end user regarding how to install or remove this RF module or change RF related parameters in the user manual of the end product. Other user manual statements may apply. L'integrateur OEM ne devraient pas fournir des informations a l'utilisateur final sur la facon d'installer ou de supprimer ce module RF ou modifier les parametres lies RF dans le manuel utilisateur du produit final. Autres declarations manuel de l'utilisateur peuvent s'appliquer. Connectivity Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 330-0237-R1.5 22 The information in this document is subject to change without notice. (c) Copyright 2017-2018 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 SaBLE-x-R2 Datasheet 15 EUROPE 15.1 CE Notice This device has been tested and certified for use in the European Union. See the Declaration of Conformity (DoC) for specifics (available on the applicable product page of the Laird website). If this device is used in a product, the OEM has responsibility to verify compliance of the final product to the EU standards. A Declaration of Conformity must be issued and kept on file as described in the 2014/53/EU - Radio Equipment Directive (RED). The CE mark must be placed on the OEM product per the labeling requirements of the directive. 16 AUSTRALIA 16.1 RCM Table 14: AS/NZS certification Radio Equipment and Systems (Short Range Devices) Standard 2014 (Amnt 1:2015) Radiocommunications (Low Interference Potential Device) Class License 2015 AS/NZS 4268: 2017 EN 300 328 v2.1.1 (2016-11) Report No.: AR742502, Dated: 25 April 2017, International Certification Corp. Radiocommunications (Electromagnetic Radiation - Human Exposure) Standard 2014 AS/NZS 2772.2:2011 Report No.: AA742502, Dated: 25 April 2017, International Certification Corp. Maximum Exposure Levels to Radio Frequency Fields - 3 KHz to 300 GHz (2002) RPS 3, ARPANSA Category B Exemption - Fixed Station Exemption, ARPANSA Schedule 5, General Public Exposure, <20mW Mean Power, Or no antenna near the body (>20 cm from unaware user) and mean output power does not exceed Table 2 threshold for testing. If this device is used in a product, the OEM has the responsibility to verify the compliance of the final end product to the Australia/New Zealand (RCM) Standards. All end-products require their own certification (SDoc). You cannot leverage the module certification and ship product into the country. Connectivity Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 330-0237-R1.5 23 The information in this document is subject to change without notice. (c) Copyright 2017-2018 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 SaBLE-x-R2 Datasheet 17 BLUETOOTH SIG QUALIFICATION The SaBLE-x-R2 module is listed on the Bluetooth SIG website as a Component Tested design. It is intended use is integration into a new End Product design by a third-party SIG member. Design Name Owner Declaration ID QD ID Link to listing on the SIG website SaBLE-x-R2 Laird Technologies D035147 96853 https://www.bluetooth.org/tpg/QLI_viewQDL.cfm?qid=35 147 It is a mandatory requirement of the Bluetooth Special Interest Group (SIG) that every product implementing Bluetooth technology has a Declaration ID. Every Bluetooth design is required to go through the qualification process, even when referencing a Bluetooth design that already has its own Declaration ID. The qualification process requires each company to registered as a member of the Bluetooth SIG - www.bluetooth.org The following link provides a link to the Bluetooth Registration page: https://www.bluetooth.org/login/register/ For each Bluetooth design it is necessary to purchase a Declaration ID. This can be done before starting the new qualification, either through invoicing or credit card payment. The fees for the Declaration ID depend on your membership status. Please refer to the following webpage: https://www.bluetooth.org/en-us/test-qualification/qualification-overview/fees For a detailed procedure of how to obtain a new Declaration ID for your design, please refer to the following SIG document: https://www.bluetooth.org/DocMan/handlers/DownloadDoc.ashx?doc_id=283698&vId=317486 17.1 Qualification Steps When Combining with a Laird Component If you wish to use a Laird component in your end product, the qualification process follows the Traditional Project route, creating a completely new design. When creating a new design, it is necessary to complete the full qualification listing process and maintain a compliance folder for the new design. The SaBLE-x-R2 design under D035147 incorporates the following Texas Instrument component; Listing reference Design Name Core Spec Version D035408 (RF-PHY) CC2640R2F SimpleLinkTM Bluetooth(R) 5.0 low energy Wireless MCU 5.0 If your design is based on un-modified SaBLE-x-R2 hardware, it is possible to use the following process; Reference the existing RF-PHY test report from the SaBLE-x-R2 listing. Combine the relevant Texas Instruments component(s) - covering as a minimum LL, L2CAP, GAP, ATT, GATT, SM). Check relevant QDID with Texas Instruments\Laird. Example component is Texas Instruments D033411) Test on PTS any standard SIG profiles that are supported in the design. Customs profiles are exempt. Connectivity Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 330-0237-R1.5 24 The information in this document is subject to change without notice. (c) Copyright 2017-2018 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 SaBLE-x-R2 Datasheet End Product Laird RF-PHY 3rd Party LL 3rd Party Host Layers Optional Profiles Figure 6: End Product design qualification scope Figure 6 shows the scope of the qualification for an End Product Design. The first step is to generate a project on the TPG (Test Plan Generator) system. This determines which test cases apply to demonstrate compliance with the Bluetooth Test Specifications. When combining qualified components in your design, and they are within their 3-year listing period, you are not required to re-test those layers covered by those components. If the design incorporates any standard SIG LE profiles (such as the Heart Rate Profile), it is necessary to test these profiles using PTS or other tools where permitted; the results are added to the compliance folder. You must upload your test declaration and test reports (where applicable) and then complete the final listing steps on the SIG website. Note: Remember to purchase your Declaration ID before you start the qualification process, as it is not possible to complete the listing without it. For further information please refer to the following training material: https://www.bluetooth.org/en-us/test-qualification/qualification-overview/listing-process-updates If you require assistance with the qualification process, please contact our recommended Bluetooth Qualification Expert (BQE), Steve Flooks, steve.flook@eurexuk.com. Connectivity Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 330-0237-R1.5 25 The information in this document is subject to change without notice. (c) Copyright 2017-2018 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 SaBLE-x-R2 Datasheet 18 ANTENNA INFORMATION 18.1 LSR Dipole Antenna See antenna datasheet. 18.2 LSR FlexPIFA See antenna datasheet. 18.3 LSR FlexNotch See antenna datasheet. 18.4 LSR mFlexPIFA See antenna datasheet. 18.5 PCB Trace Antenna AZIMUTH ROTATION AXIS AND ANGLE ELEVATION ROTATION AXIS AND ANGLE 2ND ELEVATION ROTATION AXIS AND ANGLE Figure 7: PCB trace antenna pattern measurement planes Connectivity Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 330-0237-R1.5 26 The information in this document is subject to change without notice. (c) Copyright 2017-2018 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 SaBLE-x-R2 Datasheet Table 15: PCB trace antenna gain summary Orientation Frequency (MHz) Polarization Peak Gain (dBi) Average Gain (dBi) Azimuth 2402 Vertical 0.0 -3.6 Azimuth 2402 Horizontal -6.6 -12.4 Azimuth 2440 Vertical -1.7 -5.1 Azimuth 2440 Horizontal -1.7 -13.4 Azimuth 2480 Vertical -4.3 -7.9 Azimuth 2480 Horizontal -11.5 -15.9 Elevation 2402 Vertical -7.3 -11.4 Elevation 2402 Horizontal -1.2 -5.7 Elevation 2440 Vertical -7.9 -12.6 Elevation 2440 Horizontal -7.9 -6.6 Elevation 2480 Vertical -11.0 -15.9 Elevation 2480 Horizontal -4.2 -9.1 2nd Elevation 2402 Vertical -9.4 -14.8 2 Elevation 2402 Horizontal -2.8 -7.3 2nd Elevation 2440 Vertical -10.3 -16.6 2nd Elevation 2440 Horizontal -3.4 -7.9 2nd Elevation 2480 Vertical -12.8 -18.9 2480 Horizontal -6.0 -10.4 nd nd 2 Elevation Connectivity Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 330-0237-R1.5 Average Total Gain (P) (dBi) Average Total Gain (F, P) (dBi) Average Total Gain (O, F, P) (dBi) -3.0 -4.5 -4.6 -7.3 -4.7 -5.6 -6.0 -5.9 -8.3 -6.6 -7.3 -7.7 -9.8 27 The information in this document is subject to change without notice. (c) Copyright 2017-2018 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 SaBLE-x-R2 Datasheet Vertical, Horizontal Patterns at 2402 (dB) - Azimuth Cut Cut - AzimuthMHz at 2402 MHz (dB) Antenna Patterns Vertical, HorizontalAntenna 90 0 60 120 -10 -20 30 150 -30 -40 0 180 330 210 300 240 270 Vertical Horizontal Figure 8: PCB Trace Antenna Pattern (Azimuth @ 2402 MHz) Vertical, Horizontal Antenna Patterns at 2402 MHz (dB) - Elevation Cut Vertical, Horizontal Antenna Patterns at 2402 MHz (dB) - Elevation Cut 90 0 120 60 -10 -20 150 30 -30 -40 180 0 210 330 240 300 270 Vertical Horizontal Figure 9: PCB Trace Antenna Pattern (Elevation @ 2402 MHz) Connectivity Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 330-0237-R1.5 28 The information in this document is subject to change without notice. (c) Copyright 2017-2018 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 SaBLE-x-R2 Datasheet Vertical, Horizontal Antenna Patterns at 2402 MHz (dB) - Second Elevation Cut Vertical, Horizontal Antenna Patterns at 2402 MHz (dB) - Second Elevation Cut 90 0 120 60 -10 -20 150 30 -30 -40 180 0 210 330 240 300 270 Vertical Horizontal Figure 10: PCB Trace Antenna Pattern (2nd Elevation @ 2402 MHz) Vertical, Horizontal Antenna Patterns at 2440 MHz (dB) - Azimuth Cut Vertical, Horizontal Antenna Patterns at 2440 MHz (dB) - Azimuth Cut 90 0 120 60 -10 -20 150 30 -30 -40 180 0 210 330 240 300 270 Vertical Horizontal Figure 11: PCB Trace Antenna Pattern (Azimuth @ 2440 MHz) Connectivity Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 330-0237-R1.5 29 The information in this document is subject to change without notice. (c) Copyright 2017-2018 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 SaBLE-x-R2 Datasheet Vertical, Horizontal Antenna Patterns at 2440 MHz (dB) - Elevation Cut Vertical, Horizontal Antenna Patterns at 2440 MHz (dB) - Elevation Cut 90 0 120 60 -10 -20 150 30 -30 -40 180 0 210 330 240 300 270 Vertical Horizontal Figure 12: PCB Trace Antenna Pattern (Elevation @ 2440 MHz) Vertical, Horizontal Antenna Patterns at 2440 MHz (dB) - Second Elevation Cut Vertical, Horizontal Antenna Patterns at 2440 MHz (dB) - Second Elevation Cut 90 0 120 60 -10 -20 150 30 -30 -40 180 0 210 330 240 300 270 Vertical Horizontal Figure 13: PCB Trace Antenna Pattern (2nd Elevation @ 2440 MHz) Connectivity Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 330-0237-R1.5 30 The information in this document is subject to change without notice. (c) Copyright 2017-2018 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 SaBLE-x-R2 Datasheet Vertical, Horizontal Antenna Patterns at 2480 MHz (dB) - Azimuth Cut Vertical, Horizontal Antenna Patterns at 2480 MHz (dB) - Azimuth Cut 90 0 120 60 -10 -20 150 30 -30 -40 180 0 210 330 240 300 270 Vertical Horizontal Figure 14: PCB Trace Antenna Pattern (Azimuth @ 2480 MHz) Vertical, Horizontal Antenna Patterns at 2480 MHz (dB) - Elevation Cut Vertical, Horizontal Antenna Patterns at 2480MHz (dB) - Elevation Cut 90 0 120 60 -10 -20 150 30 -30 -40 180 0 210 330 240 300 270 Vertical Horizontal Figure 15: PCB Trace Antenna Pattern (Elevation @ 2480 MHz) Connectivity Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 330-0237-R1.5 31 The information in this document is subject to change without notice. (c) Copyright 2017-2018 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 SaBLE-x-R2 Datasheet Vertical, Horizontal Antenna Patterns at 2480 MHz (dB) - Second Elevation Cut Vertical, Horizontal Antenna Patterns at 2480 MHz (dB) - Second Elevation Cut 90 0 120 60 -10 -20 150 30 -30 -40 180 0 210 330 240 300 270 Vertical Horizontal Figure 16: PCB Trace Antenna Pattern (2nd Elevation @ 2480 MHz) Connectivity Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 330-0237-R1.5 32 The information in this document is subject to change without notice. (c) Copyright 2017-2018 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 SaBLE-x-R2 Datasheet 19 MECHANICAL DATA The following are the mechanical dimensions of the SaBLE-x-R2 module. Figure 17: Module Mechanical Dimensions (Maximum Module Height = 2.4mm) Connectivity Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 330-0237-R1.5 33 The information in this document is subject to change without notice. (c) Copyright 2017-2018 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 SaBLE-x-R2 Datasheet 20 PCB FOOTPRINT Figure 18: SaBLE-x-R2 Recommended PCB Footprint (Viewed from Top) Connectivity Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 330-0237-R1.5 34 The information in this document is subject to change without notice. (c) Copyright 2017-2018 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 SaBLE-x-R2 Datasheet 20.1 Tape and Reel Dimensions Note: Module must be in this orientation when feeding tape. Figure 19: Tape and Reel Specification Connectivity Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 330-0237-R1.5 35 The information in this document is subject to change without notice. (c) Copyright 2017-2018 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 SaBLE-x-R2 Datasheet 21 DEVICE MARKINGS 21.1 450-0177 & 450-0178 21.1.1 Rev 1 Devices The shield on the 450-0177/450-0178 modules contains the following information: Laird Model: SaBLE-x-R2 Part Number and Revision: - Part Number: 450-0177 or 450-0178 - Revision: -RX (where X is the latest revision) FCC ID: TFB-1005 IC: 5969A-1005 SSYYWWD = Date Code (YY=Year, WW=Week) XXXXX = Incremental Serial Number 2D Barcode Format is Data Matrix Standard 21.1.2 Rev 2 Devices Added Giteki and C-Tick Certification The shield on the 450-0177/450-0178 modules contains the following additional information: C-Tick Logo (Australia and New Zealand Certification) Giteki Logo (Japan Certification) o o o Symbol of Radio Certification 201 CAB ID assigned by Minister of MIC 170613 (450-0177) or 170614 (450-0178) Certification number assigned by the CAB. Connectivity Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 330-0237-R1.5 36 The information in this document is subject to change without notice. (c) Copyright 2017-2018 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 SaBLE-x-R2 Datasheet 21.2 450-0194 & 450-0195 21.2.1 Rev 1 Devices The shield on the 450-0194/450-0195 modules contains the following information: Laird Model: SaBLE-x-R2 Part Number and Revision: - Part Number: 450-0194 or 450-0195 - Revision: -RX (where X is the latest revision) FCC ID: TFB-1005 IC: 5969A-1005 SSYYWWD = Date Code (YY=Year, WW=Week) XXXXX = Incremental Serial Number 2D Barcode Format is Data Matrix Standard C-Tick Logo (Australia and New Zealand Certification) Giteki Logo (Japan Certification) o o o Symbol of Radio Certification 201 CAB ID assigned by Minister of MIC 170613 (450-0177) or 170614 (450-0178) Certification number assigned by the CAB. Connectivity Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 330-0237-R1.5 37 The information in this document is subject to change without notice. (c) Copyright 2017-2018 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610 SaBLE-x-R2 Datasheet 22 CONTACTING LSR Headquarters LSR W66 N220 Commerce Court Cedarburg, WI 53012-2636 USA Tel: 1(262) 375-4400 Fax: 1(262) 375-4248 Website Technical Support Sales Contact www.lsr.com forum.lsr.com sales@lsr.com (c) Copyright 2018 Laird. All Rights Reserved. Patent pending. Any information furnished by Laird and its agents is believed to be accurate and reliable. All specifications are subject to change without notice. Responsibility for the use and application of Laird materials or products rests with the end user since Laird and its agents cannot be aware of all potential uses. Laird makes no warranties as to non-infringement nor as to the fitness, merchantability, or sustainability of any Laird materials or products for any specific or general uses. Laird, Laird Technologies, Inc., or any of its affiliates or agents shall not be liable for incidental or consequential damages of any kind. All Laird products are sold pursuant to the Laird Terms and Conditions of Sale in effect from time to time, a copy of which will be furnished upon request. When used as a tradename herein, Laird means Laird Limited due to the acquisition by Advent or one or more subsidiaries of Laird Limited. LairdTM, Laird TechnologiesTM, corresponding logos, and other marks are trademarks or registered trademarks of Laird. Other marks may be the property of third parties. Nothing herein provides a license under any Laird or any third party intellectual property right. Connectivity Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 330-0237-R1.5 38 The information in this document is subject to change without notice. (c) Copyright 2017-2018 Laird. All Rights Reserved Americas: +1-800-492-2320 Europe: +44-1628-858-940 Hong Kong: +852 2923 0610