DATA S H E E T MINIATURE SIGNAL RELAY UA2/UB2 SERIES Super-compact size, Slim-package, Surface mounting type DESCRIPTION NEC's UA2/UB2 relay ia a new generation Miniature Signal Relay of super-compact size and slim-pakage. But, the latching type production is going to start after June 2000. FEATURES TM Small mounting size of slim package for dense mounting. TM Bellcore (2500 V) and FCC (1500 V) surge capability. TM IEC950/UL1950/EN60950 spacing and high breakdown voltage. (Basic insulation class on 200 V working voltage) TM Low power consumption 140 mW APPLICATIONS Electronic switching systems, PBX, terminal equipment, telephone system, instrumental equipment. For Right Use of Miniature Relays DO NOT EXCEED MAXIMUM RATINGS. Do not use relays under exceeding conditions such as over ambient temperature, over voltage and over current. Incorrect use could result in abnormal heating, damage to related parts or cause burning. READ CAUTIONS IN THE SELECTION GUIDE. Read the cautions described in NEC's "Miniature Relays" (ER0046EJ) when you choose relays for your application. The information in this document is subject to change without notice. Document No. ER0450EJ2V0DS00 (2nd edition) Date Published January 2000 M Printed in Japan (c) 1999 UA2/UB2 SERIES DIMENSIONS AND PAD LAYOUTS (Unit : mm [inch]) UA2 SERIES mm [inch] (mm) 7.6 5.7 [0.224] 3.2 8- 0.85 2.2 2.2 3.4 [0.134] 2.8 [0.110] 3.2 0.5 [0.020] 8.0 [0.315] 10.6 [0.417] (1.5) (1.5) 3.2 2.2 2.2 [0.126] [0.087][0.087] (Bottom view) 3.2 [0.126] Note. General tolerance : 0.1 Tolerance of lead pitch is 0.15 mm [0.006 inch] Another tolerance is 0.3 mm [0.012 inch] ( ) is reference. Value of trimmed lead type (NJ type) UB2 SERIES (1.5) 2.4 3.1 5.3 2.2 3.2 [0.126] 2.2 2.2 [0.087] [0.087] 7.4 [0.291] 6.0 [0.236] Tolerance of lead pitch is 0.15 mm [0.006 inch] Another tolerance is 0.3 mm [0.012 inch] ( ) is reference. Value of minimum footprint type (NUN type) 2 2.2 0.8 (1.5) 3.2 [0.126] 3.2 5.7 [0.224] 9.0 [0.354] max. 8.8 [0.346] max. 10.6 [0.417] (mm) 7.6 DATA SHEET ER0450EJ2V0DS00 (Bottom view) Note. General tolerance : 0.1 4.6 mm [inch] UA2/UB2 SERIES PIN CONFIGURATIONS (bottom view) UA2 SERIES 1 2 3 4 1 2 3 4 8 7 6 5 R S 8 Index mark of relay direction 7 6 5 Non-latch type (not energized position) Single coil latch type (reset position) S : Coil polarity of set (operate) R : Coil polarity of reset (release) UB2 SERIES 1 2 3 4 1 2 3 4 8 7 6 5 R S Index mark of relay direction 8 7 6 5 Non-latch type (not energized position) Single coil latch type (reset position) S : Coil polarity of set (operate) R : Coil polarity of reset (release) MARKINGS (top view) 1 4 q Part number w Manufacturer 9900 UA2 - 1 2 NU e Country of origin r Date code JAPAN t Index mark of relay direction (pin No. 1, 12) 5 2 3 DATA SHEET ER0450EJ2V0DS00 3 UA2/UB2 SERIES PERFORMANCE CHARACTERISTICS (Community) Contact Form Contact Ratings 2 Form c Maximum Switching Power 30 W (resistive) 37.5 VA (resistive) Maximum Switching Voltage 220 Vdc 250 Vac Maximum Switching Current 1A Maximum Carrying Current 1A Minimum Contact Ratings 10 mV.dc, 10 A *4 Initial Contact Resistance 100 m Max. (Initial) Contact Material Nominal Operating Power Silver alloy with gold alloy overlay Non-Latch Type 140 to 230 mW Single Coil Latch Type 100 to 120 mW Operate Time (Excluding Bounce) Approximately 2 ms Release Time (Excluding Bounce) Approximately 1 ms without diode Insulation Resistance 1000 M at 500 Vdc Between Open Contacts Breakdown Voltage 1000 Vac for one minute (1500 V surge, 10 x 160 s 1) Between Adjacent Contacts Between Coil and Contact 1500 Vac for one minute (2500 V surge, 2 x 10 s *2) Shock Resistance 735 m / s2 (75 G) (misoperating) 980 m / s2 (100 G) (destructive failure) Vibration Resistance 10 to 55 Hz at double amplitude of 3 mm (20 G) (misoperating) 10 to 55 Hz, double amplitude of 5 mm (30 G) (Destructive failure) Ambient Temperature -40 to +85C Coil Temperature Rise 18 degrees at nominal coil voltage (140 mW) 5 x 107 *3 operations (Non-latch type) No-load 1 x 107 operations (Latch type) Running specifications 30 Vdc 1 A (resistive), 1 x 105 operations at 20C Load 125 Vac 0.3 A (resistive), 1 x 105 operations at 20C Weight Approximately 1 grams 1 rise time : 10 s, fall time : 160 s 2 rise time : 2 s, fall time : 10 s 3 This shows a number of operation where it can be running by which a fatal is not caused, and number of operation by wich a stesdy characteristic is maintained is 1 x 107 times. 4 This value is a reference value in the resistive load. Minimum capacity changes depending on seitching frequency and enviroment temperature and the load. SAFETY STANDARD AND RATING UL Recognized CSA Certificated (UL508)* (CSA C22.2 No14) File No E73266 File No LR46266 30 Vdc, 1 A (Resistive) 110 Vdc, 0.3 A (Resistive) 125 Vac, 0.3 A (Resistive) * Spacing : UL114, UL478 Spacing : CSAstd950 4 DATA SHEET ER0450EJ2V0DS00 UA2/UB2 SERIES PART NUMBER SYSTEM UB2 - 3 S N U - L Packing code Nil : Tube (All of UA2, To be select for UB2) L : Embossed carrying tape of L type (UB2 only) R : Embossed carrying tape of R type (UB2 only) Option NU : Standard NJ : Trimmed lead typr of UA2 NUN : Minimum footprint type of UB2 Lach typr Nil : Non-latch typr S : Single coil latch typr Nominal coil voltage A numerical value of coil voltage (See the following lineup) Series name UA2 : UA2 Series UB2 : UB2 Series NOMINAL LINEUP Non-latch Type at 20C Nominal Coil Voltage (Vdc) Coil Resistance () 10 % Must Operate Voltage (Vdc) Must Release Voltage (Vdc) Nominal operate power (mW) 1.5 16 1.13 0.15 140 3 64.3 2.25 0.3 140 4.5 145 3.38 0.45 140 5 178 3.75 0.5 140 6 257 4.5 0.6 140 9 579 6.75 0.9 140 12 1028 9.0 1.2 140 24 2504 18.0 2.4 230 Must Operate Voltage (Vdc) Must Release Voltage (Vdc) Nominal operate power (mW) 22.5 1.13 1.13 100 Single-Coil Latch Type Nominal Coil Voltage (Vdc) 1.5 3 at 20C Coil Resistance () 10 % 90 2.25 2.25 100 4.5 202.5 3.38 3.38 100 5 250 3.75 3.75 100 6 360 4.5 4.5 100 9 810 6.75 6.75 100 12 1440 9.0 9.0 100 24 4800 18.0 18.0 120 DATA SHEET ER0450EJ2V0DS00 5 UA2/UB2 SERIES 30 20 10 0 100 150 200 250 Coil Temperature Rise (deg) Coil Temperature Rise (deg) Coile Temperature Rise 30 applied power 0.23 W 20 0.14 W 10 0 0 5 Applied Power (mW) at 20 degreeC Swiching Current (A) 2.0 DC (resistive) AC (resistive) 1.0 0.5 0.2 0.1 10 20 15 20 Maximum coil voltage Maximum coil voltage (ratio to rated voltage) (%) Switching capacity 10 Energized Time (minute) 50 100 200 150 100 50 0 -40 200 -20 250V. AC 220V. DC Swiching Voltage (V) 0 20 40 60 80 Ambient Temperature (degreeC) Operate Time and Release Time (Sample : UA2-5NU) (Without diode) 4 Release Time (ms) Operate Time (ms) 4 3 2 1 0 0 100 150 200 250 3 2 1 0 0 Applied Power (mW) 6 100 150 200 Applied Power (mW) DATA SHEET ER0450EJ2V0DS00 250 100 UA2/UB2 SERIES Nonload (mechanical) Life Test (Load: Nonload, Drive: 5VDC 10 Hz 50% duty, at 20 degreeC, Sample: UA2-5 n=20) Make Contact Breake Contact Contact Resistance (mOhms) Operate Voltage Release Voltage Operate Voltage (V) Release Voltage (V) 5 4 Maximum Average 3 Minimum 2 1 0 200 100 50 20 10 0 0.5 1 5 Number of Operations ( x 0 10 10 6 0 0.5 1 5 Number of Operations ( x Times) 10 10 6 Times) Electrical Life Test (Load: 5VDC/0.1 A Resistive, Drive: 5VDC 5 Hz 50% duty, at 85 degreeC, Sample: UA2-5NU n=10) Make Contact Breake Contact Contact Resistance (mOhms) Operate Voltage Release Voltage Operate Voltage (V) Release Voltage (V) 5 4 3 2 1 0 200 100 50 20 10 0 0.5 0 1 0 0.5 Number of Operations ( x 10 6 Times) 1 Number of Operations ( x 10 6 Times) Breakdown Voltage Sample : UA2-5NU (a) Between open contact (sample : n=20) (b) Between adjacent contact (sample : n=10) Sample Rate (n) 10 5 0 0.5 1.0 5 0 1.5 1.5 2.0 Breakdown Voltage (kV) 2.5 Breakdown Voltage (kV) (c) Between coil to contact (sample : n=10) 10 Sample Rate (n) Sample Rate (n) 10 5 0 1.5 2.0 2.5 2.6 Breakdown Voltage (kV) DATA SHEET ER0450EJ2V0DS00 7 UA2/UB2 SERIES Drift of Operate Voltage +40 +30 +20 +10 0 -10 -20 -30 -40 I II III IV V Drift of Operate Voltage (%) Drift of Operate Voltage (%) Magnetic Interference VI Drift of Operate Voltage +40 +30 +20 +10 0 -10 -20 -30 -40 I II III IV V VI Measurment sample ON ON ON I OFF OFF OFF II ON Layout OFF III ON OFF ON OFF ON : emergized OFF : no emergized ON V IV 3 mm OFF VI 2.5 mm Mounting space 8 DATA SHEET ER0450EJ2V0DS00 UA2/UB2 SERIES TUBE PACKAGE (UA2, UB2) Dimension of Package (Unit : mm) 50 pieces / Tube Material : Polyvinyl chloride (anti-static treated) 15.1 560.0 10.1 Outline of Package Rubber stopper (Yellow) Rubber stopper (Green) Index Mark TAPE PACKAGE (UB2) Embossed carrying tape 1.5 (0.054) 12.0(0.47) 4.0(0.157) 0.4 (0.016) 2.2 (0.087) 15.5 (0.610) 2.0(0.079) Top cover tape A 11.5 (0.453) 24.0(0.945) Reel TAPE DIMENSION mm (inch) 1.75(0.069) APPEARANCE B UB2-NU A Max.9.4 (0.370) B 8.2 (0.323) UB2-NUN Max.9.5 (0.370) 6.7 (0.264) Relay orientation mark and tape carrying direction. Orientation mark Orientation mark Tape carrying direction Carrying tape type Part number L UB2-***-L DATA SHEET ER0450EJ2V0DS00 R UB2-****-R 9 UA2/UB2 SERIES SOLDERING TEMPERATURE CONDITION Through-hole mounting type (UA2) q Automatic soldering * Preheating : 100C max. 1 minute max. * Solder temperature : 250C max. * Solder time : 10 seconds max. w Manual soldering * Solder temperature : 350C max. * Solder time : 3 seconds max. Surface mounting type (UB2) IRS Method T max.; 235 Temperature (C) 200 175 150 30 sec. 80 sec. 200 sec. Time Note: 1. Temperature profile shows printed circuit board surface temperature on the relay terminal portion. 2. Check the actual soldering condition to use other method except above mentioned temperature profiles. 10 DATA SHEET ER0450EJ2V0DS00 UA2/UB2 SERIES GUIDE TO APPLICATIONS 1. When connecting coils, refer to the pin configuration to prevent misoperation or malfunction. 2. The latch type relay should be initialized at the appointed position (set or reset position) when using, and should be energized or deenergized to the specified polarity to avoid wrong operations by reversed contact state. 3. Ultrasonic cleaning is not recommended to keep contact performance reliable. Alcohol based solvents are available as proper solvents. 4. Pressurized stress on the relay cover may affect reliable operation. 5. Minimum contact load of the relay is 10 mVdc, 10 A. This value is a reference value in the resistance load. Minimum capacity changes depending on switching frequency and environment temperature and the load. DATA SHEET ER0450EJ2V0DS00 11 UA2/UB2 SERIES No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Corporation. NEC Corporation assumes no responsibility for any errors which may appear in this document. NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a device described herein or any other liability arising from use of such device. No license, either express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Corporation or others. While NEC Corporation has been making continuous effort to enhance the reliability of its electronic components, the possibility of defects cannot be eliminated entirely. To minimize risks of damage or injury to persons or property arising from a defect in an NEC electronic component, customers must incorporate sufficient safety measures in its design, such as redundancy, fire-containment, and antifailure features. NEC devices are classified into the following three quality grades: "Standard", "Special", and "Specific". The Specific quality grade applies only to devices developed based on a customer designated "quality assurance program" for a specific application. The recommended applications of a device depend on its quality grade, as indicated below. Customers must check the quality grade of each device before using it in a particular application. Standard: Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots Special: Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) Specific: Aircrafts, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems or medical equipment for life support, etc. The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books. If customers intend to use NEC devices for applications other than those specified for Standard quality grade, they should contact an NEC sales representative in advance. Anti-radioactive design is not implemented in this product.