DS2108 Differential SCSI Switchable Terminator www.dalsemi.com FEATURES PIN ASSIGNMENT Fully compliant with SCSI, SCSI-2 and SCSI3 standards Conforms to EIA RS-485 standard Provides differential termination for 9 pairs of signal lines Operates with SCSI signal voltages of -7 to +12 Volts Laser-trimmed 330 and 150-ohm termination resistors have 5% tolerance over full temperature range Switchable power-down mode Low power down capacitance of 6 pF 24-pin plastic SOIC (DS2108S) TPWR R1N R2N R3N R4N R5N R6N R7N R8N R9N TPWR NC 1 2 3 4 5 6 7 8 9 10 11 12 24 23 22 21 20 19 18 17 16 15 14 13 PD GND R1P R2P R3P R4P R5P R6P R7P R8P R9P GND DS2108S 24-Pin SOIC (300-mil) DESCRIPTION The DS2108 SCSI Terminator has been specifically designed for High Voltage Differential (HVD) SCSI systems requiring switchable termination. The DS2108 integrates eighteen 330-ohm and nine 150-ohm precise switched termination resistors into a monolithic IC. The surface mount SOIC package saves board space over conventional resistor SIPs. The termination resistors can be isolated from the SCSI bus under software or hardware control. While in the powered down mode, the DS2108 isolates the nine terminator blocks from the bus while adding only 6 pF capacitance to each signal line of the SCSI bus. FUNCTIONAL DESCRIPTION The DS2108 consists of power-down circuitry, eighteen 330-ohm and nine 150-ohm termination resistors (Figure 1). The DS2108 can be removed from the circuit by bringing the power down pin (PD) low. The power down capacitance on the terminating resistors is 6 pF, well below the SCSI-3 allotment of 25 pF. The DS2108 supports SCSI signal voltages of -7 to +12 volts when powered on or off. When all lines settle into the quiescent state (no signal transitions), 56 mA is typically consumed. Only 1 mA is typically consumed in the powered down mode. 1 of 5 112099 DS2108 DS2108 BLOCK DIAGRAM Figure 1 2 of 5 DS2108 TYPICAL DIFFERENTIAL SCSI BUS CONFIGURATION Figure 2 NOTES: 1. Two DS2108s required per 8-bit SCSI device and three DS2108s per 16-bit SCSI device. 2. Mid-bus termination effectively removed by grounding PD pin. 3. Termination power to be provided as specified in SCSI-3 Parallel Interface (SPI) document. 4. Local TERMPWR bypassing is recommended by the SPI document with values shown. The bypass capacitors should be located as close as possible to the DS2108s. Only one pair of capacitors is required per SCSI device (may be shared between DS2108s on same device). PIN DESCRIPTION Table 1 PIN 1, 11 2, 3, 4, 5, 6, 7, 8, 9, 10 12 13, 23 14, 15, 16, 17, 18, 19, 20, 21, 22 24 SYMBOL TPWR DESCRIPTION Termination Power. Should be connected to the SCSI TERMPWR line. Bypass with a 2.2 F cap in parallel with a 0.1 F cap as shown in Figure 2. R1N...R9N Signal Termination Negative. Connect to -SIGNAL of SCSI bus. NC GND R1P...R9P PD No Connect. Do not connect any signal to this pin. Ground. Signal ground; 0.0V. Signal Termination Positive. Connect to +SIGNAL of SCSI bus. Power Down. When tied low, the DS2108 enters a power-down mode. Contains an internal 50K pull-up. Strap low to deactivate the DS2108, leave open circuited to activate the DS2108. 3 of 5 DS2108 ABSOLUTE MAXIMUM RATINGS* Voltage on Any Pin Relative to Ground Operating Temperature Storage Temperature Soldering Temperature -7.0V to +12.0V 0C to 70C -55C to +125C 260C for 10 seconds * This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. RECOMMENDED OPERATING CONDITIONS PARAMETER TERMPWR Voltage PD Active PD Inactive SYM VTP VPDA VPDI (0C to 70C) MIN 4.00 -0.3 2.00 TYP MAX 5.25 0.8 VTP + 0.3 UNITS V V V NOTES SYMBOL ITP IPD Vem MIN TYP 56 1 MAX 65 2 12.0 UNITS mA mA V NOTES 1, 6 1, 5 7, 8 RTTN RTNP RTPG CPD 313.5 142.5 313.5 330 150 330 5 346.5 157.5 346.5 6 ohms ohms ohms pF 2 3 4 1, 5, 7 DC CHARACTERISTICS PARAMETER TERMPWR Current Power-down Current Command Mode Voltage Termination Resistance Termination Resistance Termination Resistance Power-down Termination Capacitance 7.0 NOTES: 1. 4.00V < TERMPWR < 5.25V 2. 330 =resistor between TERMPWR and -SIGNAL. 3. 150 =resistor between -SIGNAL and +SIGNAL. 4. 330 =resistor between +SIGNAL and GDN. 5. PD = 0.0V. 6. Signal pins left open. 7. Guaranteed by design; not production tested. 8. Signal lines RxN and RxP only. 4 of 5 DS2108 24-PIN SOIC (300-MIL) The chamfer on the body is optional. If it is not present, a terminal 1 identifier must be positioned so that 1/2 or more of its area is contained in the hatched zone. PKG DIM A IN. MM A1 IN. MM A2 IN. MM b IN. MM C IN. MM D IN. MM e IN. MM E1 IN. MM H IN. MM L IN. MM 24-PIN MIN MAX 0.094 0.105 2.38 2.68 0.004 0.012 0.102 0.30 0.089 0.095 2.26 2.41 0.013 0.020 0.33 0.51 0.009 0.013 0.229 0.33 0.598 0.612 15.19 15.54 0.050 BSC 1.27 BSC 0.290 0.300 7.37 7.62 0.398 0.416 10.11 10.57 0.016 0.040 0.40 1.02 0 8 5 of 5