TPA2005D1 www.ti.com............................................................................................................................................................... SLOS369F - JULY 2002 - REVISED JULY 2008 1.4-W MONO FILTER-FREE CLASS-D AUDIO POWER AMPLIFIER FEATURES 1 * 1.4 W Into 8 From a 5 V Supply at THD = 10% (Typ) * Maximum Battery Life and Minimum Heat - Efficiency With an 8- Speaker: - 84% at 400 mW - 79% at 100 mW - 2.8-mA Quiescent Current - 0.5-A Shutdown Current * Capable of Driving an 8- Speaker (2.5 V VDD 5.5 V) and a 4- Speaker (2.5 V VDD 4.2 V) * Only Three External Components - Optimized PWM Output Stage Eliminates LC Output Filter - Internally Generated 250-kHz Switching Frequency Eliminates Capacitor and Resistor - Improved PSRR (-71 dB at 217 Hz) and Wide Supply Voltage (2.5 V to 5.5 V) Eliminates Need for a Voltage Regulator - Fully Differential Design Reduces RF Rectification and Eliminates Bypass Capacitor - Improved CMRR Eliminates Two Input Coupling Capacitors * Space Saving Package - 3 mm x 3 mm QFN package (DRB) - 2,5 mm x 2,5 mm MicroStar JuniorTM 2 * BGA Package (ZQY) - 3 mm x 5 mm MSOP PowerPADTM Package (DGN) - TPA2010D1 Available in 1,45 mm x 1,45 mm WCSP (YZF) Use TPA2006D1 for 1.8 V Logic Compatibility on Shutdown Pin APPLICATIONS * Ideal for Wireless or Cellular Handsets and PDAs DESCRIPTION The TPA2005D1 is a 1.4-W high efficiency filter-free class-D audio power amplifier in a MicroStar JuniorTM BGA, QFN, or MSOP package that requires only three external components. Features like 84% efficiency, -71-dB PSRR at 217 Hz, improved RF-rectification immunity, and 15 mm2 total PCB area make the TPA2005D1 ideal for cellular handsets. A fast start-up time of 9 ms with minimal pop makes the TPA2005D1 ideal for PDA applications. In cellular handsets, the earpiece, speaker phone, and melody ringer can each be driven by the TPA2005D1. The device allows independent gain control by summing the signals from each function while minimizing noise to only 48 VRMS. The TPA2005D1 protection. has short-circuit and thermal APPLICATION CIRCUIT To Battery Internal Oscillator + RI Differential Input - RI CS IN- _ PWM CS VO+ H- Bridge VO- + 2.5 mm RI IN+ GND SHUTDOWN Actual Solution Size (MicroStar Junior BGA) VDD Bias Circuitry TPA2005D1 RI 6 mm 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. MicroStar Junior, PowerPAD are trademarks of Texas Instruments. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2002-2008, Texas Instruments Incorporated TPA2005D1 SLOS369F - JULY 2002 - REVISED JULY 2008............................................................................................................................................................... www.ti.com These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. ORDERING INFORMATION PACKAGE (1) TA PART NUMBER MicroStar JuniorTM (GQY) MicroStar JuniorTM (ZQY) (3) -40C to 85C 8-pin QFN (DRB) 8-pin MSOP (DGN) (1) (2) (3) TPA2005D1GQYR SYMBOL (2) PB051 TPA2005D1ZQYR (2) TPA2005D1DRBR AAFI (2) BIQ TPA2005D1DGN(R) BAL For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website at www.ti.com. The GQY, ZQY, and DRB packages are only available taped and reeled. An R at the end of the part number indicates the devices are taped and reeled. The GQY is the standard MicroStar JuniorTM package. The ZQY is lead-free option, and is qualified for 260 lead-free assembly. ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range unless otherwise noted (1) UNIT VDD Supply voltage (2) VI Input voltage In active mode -0.3 V to 6 V In SHUTDOWN mode -0.3 V to 7 V -0.3 V to VDD + 0.3 V Continuous total power dissipation See Dissipation Rating Table TA Operating free-air temperature TJ Operating junction temperature -40C to 85C Tstg Storage temperature -65C to 150C RL Load resistance (1) (2) -40C to 85C 2.5 VDD 4.2 V 3.2 (Minimum) 4.2 < VDD 6 V 6.4 (Minimum) Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. For the MSOP (DGN) package option, the maximum VDD should be limited to 5 V if short-circuit protection is desired. RECOMMENDED OPERATING CONDITIONS MIN VDD Supply voltage VIH High-level input voltage VIL Low-level input voltage RI Input resistor Gain 20 V/V (26 dB) VIC Common mode input voltage range VDD = 2.5 V, 5.5 V, CMRR -49 dB TA Operating free-air temperature NOM MAX UNIT 2.5 5.5 V SHUTDOWN 2 VDD V SHUTDOWN 0 0.8 15 V k 0.5 VDD-0.8 V -40 85 C DISSIPATION RATINGS PACKAGE 2 DERATING FACTOR TA 25C POWER RATING TA = 70C POWER RATING TA = 85C POWER RATING GQY, ZQY 16 mW/C 2W 1.28 W 1.04 W DRB 21.8 mW/C 2.7 W 1.7 W 1.4 W DGN 17.1 mW/C 2.13 W 1.36 W 1.11 W Submit Documentation Feedback Copyright (c) 2002-2008, Texas Instruments Incorporated Product Folder Link(s): TPA2005D1 TPA2005D1 www.ti.com............................................................................................................................................................... SLOS369F - JULY 2002 - REVISED JULY 2008 ELECTRICAL CHARACTERISTICS TA = 25C (unless otherwise noted) PARAMETER TEST CONDITIONS MIN |VOS| Output offset voltage (measured differentially) VI = 0 V, AV = 2 V/V, VDD = 2.5 V to 5.5 V PSRR Power supply rejection ratio VDD = 2.5 V to 5.5 V CMRR Common mode rejection ratio VDD = 2.5 V to 5.5 V, VIC= VDD/2 to 0.5 V, VIC= VDD/2 to VDD- 0.8 V |IIH| High-level input current |IIL| Low-level input current I(Q) Quiescent current I(SD) Shutdown current rDS(on) f(sw) Static drain-source on-state resistance TYP MAX UNIT 25 mV -75 -55 dB -68 -49 dB VDD = 5.5 V, VI = 5.8 V 50 A VDD = 5.5 V, VI = 0.3 V 1 A VDD = 5.5 V, no load 3.4 VDD = 3.6 V, no load 2.8 VDD = 2.5 V, no load 2.2 3.2 V(SHUTDOWN) = 0.8 V, VDD = 2.5 V to 5.5 V 0.5 2 VDD = 2.5 V 770 VDD = 3.6 V 590 VDD = 5.5 V 500 Output impedance in SHUTDOWN V(SHUTDOWN) = 0.8 V Switching frequency VDD = 2.5 V to 5.5 V Gain 4.5 mA m >1 200 142 kW RI 2 k 250 2 150 kW RI A 300 158 kW RI 2 kHz V V OPERATING CHARACTERISTICS TA = 25C, Gain = 2 V/V, RL = 8 (unless otherwise noted) PARAMETER TEST CONDITIOINS THD + N= 1%, f = 1 kHz, RL = 8 PO Output power THD + N= 10%, f = 1 kHz, RL = 8 THD+N Total harmonic distortion plus noise MIN TYP VDD = 5 V 1.18 VDD = 3.6 V 0.58 VDD = 2.5 V 0.26 VDD = 5 V 1.45 VDD = 3.6 V 0.75 VDD = 2.5 V 0.35 MAX UNIT W W PO = 1 W, f = 1 kHz, RL = 8 VDD = 5 V 0.18% PO = 0.5 W, f = 1 kHz, RL = 8 VDD = 3.6 V 0.19% PO = 200 mW, f = 1 kHz, RL = 8 VDD = 2.5 V 0.20% VDD = 3.6 V -71 dB dB kSVR Supply ripple rejection ratio f = 217 Hz, V(RIPPLE) = 200 mVpp Inputs ac-grounded with Ci = 2 F SNR Signal-to-noise ratio PO= 1 W, RL = 8 VDD = 5 V 97 Vn Output voltage noise VDD = 3.6 V, f = 20 Hz to 20 kHz, Inputs ac-grounded with Ci = 2 F No weighting 48 A weighting 36 CMRR Common mode rejection ratio VIC = 1 Vpp , f = 217 Hz VDD = 3.6 V ZI Input impedance -63 142 Start-up time from shutdown VDD = 3.6 V VRMS 150 dB 158 9 Submit Documentation Feedback Copyright (c) 2002-2008, Texas Instruments Incorporated Product Folder Link(s): TPA2005D1 k ms 3 TPA2005D1 SLOS369F - JULY 2002 - REVISED JULY 2008............................................................................................................................................................... www.ti.com PIN ASSIGNMENTS 8-PIN QFN (DRB) PACKAGE (TOP VIEW) MicroStar Juniort (GQY) PACKAGE (TOP VIEW) SHUTDOWN NC IN+ IN- (A1) (B1) (C1) (D1) (A4) (B4) (C4) (D4) (SIDE VIEW) VO- SHUTDOWN VDD NC VDD VO+ IN+ 1 3 6 VDD IN- 4 5 VO+ GND 8-PIN MSOP (DGN) PACKAGE (TOP VIEW) 8 V O- 2 SHUTDOWN 1 8 VO- NC 2 7 GND IN+ 3 6 VDD IN- 4 5 VO+ 7 GND NC - No internal connection NOTES A. The shaded terminals are used for electrical and thermal connections to the ground plane. All the shaded terminals need to be electrical connected to ground. No connect (NC) terminals still need a pad and trace. B. The thermal pad of the DRB and DGN packages must be electrically and thermally connected to a ground plane. Terminal Functions TERMINAL NAME I/O DESCRIPTION ZQY, GQY DRB, DGN IN- D1 4 I Negative differential input IN+ C1 3 I Positive differential input VDD B4, C4 6 I Power supply VO+ D4 5 O Positive BTL output GND A2, A3, B3, C2, C3, D2, D3 7 I High-current ground VO- A4 8 O Negative BTL output SHUTDOWN A1 1 I Shutdown terminal (active low logic) NC B1 2 No internal connection Thermal Pad Must be soldered to a grounded pad on the PCB. FUNCTIONAL BLOCK DIAGRAM Gain = 2 V/V VDD B4, C4 VDD 150 k IN- D1 _ + + _ Deglitch Logic Gate Drive + _ Deglitch Logic Gate Drive A4 VO- _ + _ + + _ IN+ C1 150 k SHUTDOWN 4 A1 TTL SD Input Buffer Biases and References Ramp Generator Startup & Thermal Protection Logic D4 VO+ Short Circuit Detect GND A2, A3, B3, C2, C3, D2, D3 (terminal labels for MicroStar Junior package) Submit Documentation Feedback Copyright (c) 2002-2008, Texas Instruments Incorporated Product Folder Link(s): TPA2005D1 TPA2005D1 www.ti.com............................................................................................................................................................... SLOS369F - JULY 2002 - REVISED JULY 2008 TYPICAL CHARACTERISTICS Table of Graphs FIGURE Efficiency vs Output power Power dissipation vs Output power 3 Supply current vs Output power 4, 5 I(Q) Quiescent current vs Supply voltage 6 I(SD) Shutdown current vs Shutdown voltage 7 PD PO Output power THD+N Total harmonic distortion plus noise 1, 2 vs Supply voltage 8 vs Load resistance 9, 10 vs Output power 11, 12 vs Frequency 13, 14, 15, 16 vs Common-mode input voltage kSVR vs Frequency Supply voltage rejection ratio GSM power supply rejection CMRR 17 Common-mode rejection ratio 18, 19, 20 vs Common-mode input voltage 21 vs Time 22 vs Frequency 23 vs Frequency 24 vs Common-mode input voltage 25 TEST SET-UP FOR GRAPHS CI TPA2005D1 RI + Measurement Output - IN+ CI OUT+ Load RI IN- VDD + OUT- 30 kHz Low Pass Filter + Measurement Input - GND 1 F VDD - Notes: (1) CI was Shorted for any Common-Mode input voltage measurement (2) A 33-H inductor was placed in series with the load resistor to emulate a small speaker for efficiency measurements. (3) The 30-kHz low-pass filter is required even if the analyzer has a low-pass filter. An RC filter (100 W, 47 nF) is used on each output for the data sheet graphs. Submit Documentation Feedback Copyright (c) 2002-2008, Texas Instruments Incorporated Product Folder Link(s): TPA2005D1 5 TPA2005D1 SLOS369F - JULY 2002 - REVISED JULY 2008............................................................................................................................................................... www.ti.com EFFICIENCY vs OUTPUT POWER EFFICIENCY vs OUTPUT POWER 90 90 RL = 32 W, 33 mH 90 80 80 RL = 8 W, 33 mH 70 Efficiency - % RL = 16 W, 33 mH 60 50 40 30 Class-AB, RL = 8 20 10 70 VDD = 2.5 V, 60 RL = 8W, 33mH VDD = 5 V, 80 RL = 8W, 33mH 70 Efficiency - % 100 Efficiency - % EFFICIENCY vs OUTPUT POWER 50 40 Class-AB, VDD = 5 V, RL = 8 W 30 20 VDD = 3.6 0.1 0.2 0.3 0.4 0.5 0 0.6 0.2 0.4 0.6 0.8 1 0 0 1.2 Figure 3. POWER DISSIPATION vs OUTPUT POWER SUPPLY CURRENT vs OUTPUT POWER SUPPLY CURRENT vs OUTPUT POWER 300 250 VDD = 3.6 V 0.4 RL = 4 W, 33 mH 0.3 VDD = 3.6 V, RL = 8 W, 33 mH 0.2 RL = 8 , 33 H 150 100 50 0.1 VDD = 5 V, RL = 8 W, 33 mH 0 0.2 0.4 0.6 0.8 1 RL = 32 , 33 H 0 0 1.2 200 150 VDD = 5 V, RL = 8 , 33 H 100 VDD = 3.6 V, RL = 8 , 33 H 50 0.1 PO - Output Power - W 0.2 0.3 0.4 PO - Output Power - W VDD = 2.5 V, RL = 8 , 33 H 0 0.5 0 0.6 0.2 0.4 0.6 0.8 1 Figure 5. Figure 6. QUIESCENT CURRENT vs SUPPLY VOLTAGE SHUTDOWN CURRENT vs SHUTDOWN VOLTAGE OUTPUT POWER vs SUPPLY VOLTAGE 3.8 1 1.6 3.6 0.9 1.4 3.2 3 2.8 No Load 2.6 2.4 2.2 0.8 PO - Output Power - W RL = 8 , 33 H 0.7 0.6 VDD = 2.5 V 0.5 0.4 VDD = 3.6 V 0.3 VDD = 5 V 3.5 4 4.5 5 5.5 VDD - Supply Voltage - V Figure 7. 1.2 1 THD+N = 10% 0.8 0.6 THD+N = 1% 0.4 0.2 0 0 3 RL = 8 f = 1 kHz Gain = 2 V/V 0.2 0.1 2 1.2 PO - Output Power - W Figure 4. I (SD) - Shutdown Current - A I (Q) - Quiescent Current - mA Supply Current - mA Class-AB, VDD = 3.6 V, RL = 8 W 0.5 250 200 VDD = 4.2 V, Supply Current - mA PD - Power Dissipation - W 0.6 2.5 1.5 Figure 2. Class-AB, V DD = 5 V, RL = 8 W 3.4 0.5 1 PO - Output Power - W Figure 1. 0.7 6 30 PO - Output Power - W PO - Output Power - W 0 40 10 0 0 50 20 10 0 VDD = 4.2 V, RL = 4 W, 33 mH 60 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 Shutdown Voltage - V Figure 8. Submit Documentation Feedback 0.8 2.5 3 3.5 4 4.5 5 VDD - Supply Voltage - V Figure 9. Copyright (c) 2002-2008, Texas Instruments Incorporated Product Folder Link(s): TPA2005D1 TPA2005D1 www.ti.com............................................................................................................................................................... SLOS369F - JULY 2002 - REVISED JULY 2008 OUTPUT POWER vs SUPPLY VOLTAGE OUTPUT POWER vs LOAD RESISTANCE 1.4 R L = 4 W, f = 1kHz, Gain = 2 V/V 1.2 PO - Output Power - W THD+N = 10% 1 0.8 THD+N = 1% 0.6 0.4 VDD = 3.6 V VDD = 4.2 V 0.8 VDD = 5 V 0.6 0.4 VDD = 5 V 1.2 VDD = 4.2 V 1 VDD = 3.6 V 0.8 0.6 0.4 0.2 VDD = 2.5 V 0 0 2.5 3 3.5 4 VDD - Supply Voltage - V 4 4.5 8 12 16 20 24 RL - Load Resistance - W 28 VDD = 2.5 V 0 4 32 8 12 16 20 24 RL - Load Resistance - W 28 32 Figure 11. Figure 12. TOTAL HARMONIC DISTORTION + NOISE vs OUTPUT POWER TOTAL HARMONIC DISTORTION + NOISE vs OUTPUT POWER TOTAL HARMONIC DISTORTION + NOISE vs OUTPUT POWER 30 20 10 R L = 4 W, f = 1 kHz, Gain = 2 V/V VDD = 2.5 V 5 VDD = 3.6 V 2 VDD = 4.2 V 1 0.5 0.2 0.1 0.01 0.1 1 2 30 20 10 RL = 8 , f = 1 kHz, Gain = 2 V/V 5 2.5 V 2 3.6 V 1 5V 0.5 0.2 0.1 0.01 0.1 1 2 THD+N - Total Harmonic Distortion + Noise - % Figure 10. THD+N - Total Harmonic Distortion + Noise - % THD+N - Total Harmonic Distortion + Noise - % 1.4 1 0.2 0.2 30 20 RL = 16 , f = 1 kHz, Gain = 2 V/V 10 5 2.5 V 2 3.6 V 1 5V 0.5 0.2 0.1 0.01 0.1 1 2 PO - Output Power - W PO - Output Power - W Figure 13. Figure 14. Figure 15. TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY 10 VDD = 5 V CI = 2 F RL = 8 Gain = 2 V/V 5 2 1 0.5 0.2 50 mW 0.1 1W 0.05 0.02 250 mW 20 100 1k f - Frequency - Hz 20 k THD+N - Total Harmonic Distortion + Noise - % PO - Output Power - W THD+N - Total Harmonic Distortion + Noise - % f = 1 kHz, THD+N = 10%, Gain = 2 V/V 1.6 Figure 16. 10 5 2 VDD = 3.6 V CI = 2 F RL = 8 Gain = 2 V/V 1 0.5 0.2 500 mW 25 mW 0.1 0.05 125 mW 0.02 0.01 20 100 1k f - Frequency - Hz Figure 17. 20 k THD+N - Total Harmonic Distortion + Noise - % PO - Output Power - W 1.4 1.8 f = 1 kHz, THD+N = 1%, Gain = 2 V/V 1.2 PO - Output Power - W 1.6 0.008 OUTPUT POWER vs LOAD RESISTANCE 10 VDD = 2.5 V CI = 2 F RL = 8 Gain = 2 V/V 5 2 1 15 mW 75 mW 0.5 0.2 0.1 200 mW 0.05 0.02 0.01 20 100 1k Figure 18. Submit Documentation Feedback Copyright (c) 2002-2008, Texas Instruments Incorporated Product Folder Link(s): TPA2005D1 20 k f - Frequency - Hz 7 TPA2005D1 SLOS369F - JULY 2002 - REVISED JULY 2008............................................................................................................................................................... www.ti.com VDD = 3.6 V CI = 2 F RL = 16 Gain = 2 V/V 5 2 1 0.5 0.2 15 mW 0.1 75 mW 0.05 0.02 0.01 200 mW 20 100 1k 20 k 10 VDD = 4.2 V, R L = 4 W, Gain = 2 V/V 5 2 500 mW 1 0.5 250 mW 1W 0.2 0.1 0.05 0.02 0.01 20 100 VDD = 3.6 V, R L = 4 W, Gain = 2V/V 5 2 1 250 mW 0.5 775 mW 500 mW 0.2 0.1 0.05 0.02 0.01 20 100 1k f-Frequency-Hz 20k Figure 21. TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY TOTAL HARMONIC DISTORTION + NOISE vs COMMON MODE INPUT VOLTAGE SUPPLY VOLTAGE REJECTION RATIO vs FREQUENCY 75 mW 2 15 mW 1 0.5 200 mW 0.2 0.1 0.05 0.02 0.01 20 100 1k f - Frequency - Hz 20k 10 - Supply Voltage Rejection Ratio - dB SVR VDD = 2.5 V, R L = 4 W, Gain = 2V/V 5 f = 1 kHz PO = 200 mW 1 VDD = 2.5 V VDD = 3.6 V 0.1 k 10 THD+N - Total Harmonic Distortion + Noise - % Figure 20. 0 0 CI = 2 F RL = 8 Vp-p = 200 mV Inputs ac-Grounded Gain = 2 V/V -10 -20 -30 -40 VDD = 3.6 V -50 VDD =2. 5 V -60 -70 VDD = 5 V -80 20 0.5 1 1.5 2 2.5 3 3.5 VIC - Common Mode Input Voltage - V 100 1k f - Frequency - Hz 20 k Figure 22. Figure 23. Figure 24. SUPPLY VOLTAGE REJECTION RATIO vs FREQUENCY SUPPLY VOLTAGE REJECTIO RATIO vs FREQUENCY SUPPLY VOLTAGE REJECTION RATIO vs COMMON-MODE INPUT VOLTAGE -20 -30 VDD = 2. 5 V -40 -50 VDD = 5 V -60 -70 VDD = 3.6 V -80 100 1k f - Frequency - Hz 20 k Figure 25. -20 -30 - Supply Voltage Rejection Ratio - dB -10 0 0 -10 CI = 2 F RL = 8 Inputs Floating Gain = 2 V/V -40 -50 -60 VDD = 3.6 V -70 -80 SVR Gain = 5 V/V CI = 2 F RL = 8 Vp-p = 200 mV Inputs ac-Grounded -90 -100 20 k - Supply Voltage Rejection Ratio - dB SVR 0 20 8 20k 10 Figure 19. k k - Supply Voltage Rejection Ratio - dB SVR THD+N - Total Harmonic Distortion + Noise - % f - Frequency - Hz 1k f - Frequency - Hz TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY THD+N - Total Harmonic Distortion + Noise - % 10 TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY THD+N - Total Harmonic Distortion + Noise - % THD+N - Total Harmonic Distortion + Noise - % TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY 100 1k f - Frequency - Hz Figure 26. Submit Documentation Feedback 20 k f = 217 Hz RL = 8 Gain = 2 V/V -10 -20 -30 -40 VDD = 2.5 V -50 VDD = 3.6 V -60 -70 -80 VDD = 5 V -90 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 VIC - Common Mode Input Voltage - V Figure 27. Copyright (c) 2002-2008, Texas Instruments Incorporated Product Folder Link(s): TPA2005D1 TPA2005D1 www.ti.com............................................................................................................................................................... SLOS369F - JULY 2002 - REVISED JULY 2008 GSM POWER SUPPLY REJECTION vs FREQUENCY 0 C1 - Duty 12.6% -50 C1 Frequency 216.7448 Hz -100 C1 - Amplitude 512 mV C1 - High 3.544 V VOUT VO - Output Voltage - dBV Voltage - V VDD 0 VDD Shown in Figure 22 CI = 2 F, Inputs ac-grounded Gain = 2V/V -50 -100 -150 0 400 t - Time - ms 800 1200 1600 2000 f - Frequency - Hz Figure 28. Figure 29. COMMON-MODE REJECTION RATIO vs FREQUENCY COMMON-MODE REJECTION RATIO vs COMMON-MODE INPUT VOLTAGE 0 -10 -20 CMRR - Common Mode Rejection Ratio - dB CMRR - Common Mode Rejection Ratio - dB -150 V DD - Supply Voltage - dBV GSM POWER SUPPLY REJECTION vs TIME VDD = 2.5 V to 5 V VIC = 1 Vp-p RL = 8 Gain = 2 V/V -30 -40 -50 -60 -70 20 100 1k f - Frequency - Hz 0 RL = 8 Gain = 2 V/V -10 -20 -30 -40 VDD = 2.5 V VDD = 3.6 V -50 -60 -70 -80 VDD = 5 V -90 -100 20 k Figure 30. 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 VIC - Common Mode Input Voltage - V 5 Figure 31. Submit Documentation Feedback Copyright (c) 2002-2008, Texas Instruments Incorporated Product Folder Link(s): TPA2005D1 9 TPA2005D1 SLOS369F - JULY 2002 - REVISED JULY 2008............................................................................................................................................................... www.ti.com APPLICATION INFORMATION FULLY DIFFERENTIAL AMPLIFIER The TPA2005D1 is a fully differential amplifier with differential inputs and outputs. The fully differential amplifier consists of a differential amplifier and a common-mode amplifier. The differential amplifier ensures that the amplifier outputs a differential voltage on the output that is equal to the differential input times the gain. The common-mode feedback ensures that the common-mode voltage at the output is biased around VDD/2 regardless of the common-mode voltage at the input. The fully differential TPA2005D1 can still be used with a single-ended input; however, the TPA2005D1 should be used with differential inputs when in a noisy environment, like a wireless handset, to ensure maximum noise rejection. Advantages of Fully Differential Amplifiers * Input-coupling capacitors not required: - The fully differential amplifier allows the inputs to be biased at voltage other than mid-supply. For example, if a codec has a midsupply lower than the midsupply of the TPA2005D1, the common-mode feedback circuit will adjust, and the TPA2005D1 outputs will still be biased at midsupply of the TPA2005D1. The inputs of the TPA2005D1 can be biased from 0.5 V to VDD - 0.8 V. If the inputs are biased outside of that range, input-coupling capacitors are required. * Midsupply bypass capacitor, C(BYPASS), not required: - The fully differential amplifier does not require a bypass capacitor. This is because any shift in the midsupply affects both positive and negative channels equally and cancels at the differential output. * Better RF-immunity: - GSM handsets save power by turning on and shutting off the RF transmitter at a rate of 217 Hz. The transmitted signal is picked-up on input and output traces. The fully differential amplifier cancels the signal much better than the typical audio amplifier. COMPONENT SELECTION Figure 32 shows the TPA2005D1 typical schematic with differential inputs and Figure 33 shows the TPA2005D1 with differential inputs and input capacitors, and Figure 34 shows the TPA2005D1 with single-ended inputs. Differential inputs should be used whenever possible because the single-ended inputs are much more susceptible to noise. Table 1. Typical Component Values (1) REF DES VALUE EIA SIZE MANUFACTURER RI 150 k (0.5%) 0402 Panasonic PART NUMBER ERJ2RHD154V CS 1 F (+22%, -80%) 0402 Murata GRP155F50J105Z CI (1) 3.3 nF (10%) 0201 Murata GRP033B10J332K CI is only needed for single-ended input or if VICM is not between 0.5 V and VDD - 0.8 V. CI = 3.3 nF (with RI = 150 k) gives a high-pass corner frequency of 321 Hz. To Battery Internal Oscillator + RI - RI CS IN- _ Differential Input VDD PWM H- Bridge VO+ VO- + IN+ GND SHUTDOWN Bias Circuitry TPA2005D1 Filter-Free Class D Figure 32. Typical TPA2005D1 Application Schematic With Differential Input for a Wireless Phone 10 Submit Documentation Feedback Copyright (c) 2002-2008, Texas Instruments Incorporated Product Folder Link(s): TPA2005D1 TPA2005D1 www.ti.com............................................................................................................................................................... SLOS369F - JULY 2002 - REVISED JULY 2008 To Battery CI Internal Oscillator RI CI RI CS IN- PWM _ Differential Input VDD H- Bridge VO+ VO- + IN+ GND Bias Circuitry SHUTDOWN TPA2005D1 Filter-Free Class D Figure 33. TPA2005D1 Application Schematic With Differential Input and Input Capacitors To Battery CI Single-ended Input Internal Oscillator RI CS IN- _ RI VDD PWM H- Bridge VO- + IN+ CI SHUTDOWN VO+ GND Bias Circuitry TPA2005D1 Filter-Free Class D Figure 34. TPA2005D1 Application Schematic With Single-Ended Input Submit Documentation Feedback Copyright (c) 2002-2008, Texas Instruments Incorporated Product Folder Link(s): TPA2005D1 11 TPA2005D1 SLOS369F - JULY 2002 - REVISED JULY 2008............................................................................................................................................................... www.ti.com Input Resistors (RI) The input resistors (RI) set the gain of the amplifier according to equation Equation 1. Gain + 2 150 kW R I (1) Resistor matching is important in fully differential amplifiers. The balance of the output on the reference voltage depends on matched ratios of the resistors. CMRR, PSRR, and cancellation of the second harmonic distortion diminish if resistor mismatch occurs. Therefore, it is recommended to use 1% tolerance resistors or better to keep the performance optimized. Matching is more important than overall tolerance. Resistor arrays with 1% matching can be used with a tolerance greater than 1%. Place the input resistors close to the TPA2005D1 to limit noise injection on the high-impedance nodes. For optimal performance the gain should be set to 2 V/V or lower. Lower gain allows the TPA2005D1 to operate at its best, and keeps a high voltage at the input making the inputs less susceptible to noise. Decoupling Capacitor (CS) The TPA2005D1 is a high-performance class-D audio amplifier that requires adequate power supply decoupling to ensure the efficiency is high and total harmonic distortion (THD) is low. For higher frequency transients, spikes, or digital hash on the line, a good low equivalent-series-resistance (ESR) ceramic capacitor, typically 1 F, placed as close as possible to the device VDD lead works best. Placing this decoupling capacitor close to the TPA2005D1 is important for the efficiency of the class-D amplifier, because any resistance or inductance in the trace between the device and the capacitor can cause a loss in efficiency. For filtering lower-frequency noise signals, a 10 F or greater capacitor placed near the audio power amplifier would also help, but it is not required in most applications because of the high PSRR of this device. Input Capacitors (CI) The TPA2005D1 does not require input coupling capacitors if the design uses a differential source that is biased from 0.5 V to VDD - 0.8 V (shown in Figure 32). If the input signal is not biased within the recommended common-mode input range, if needing to use the input as a high pass filter (shown in Figure 33), or if using a single-ended source (shown in Figure 34), input coupling capacitors are required. The input capacitors and input resistors form a high-pass filter with the corner frequency, fc, determined in equation Equation 2. 1 fc + 2p R C I I (2) The value of the input capacitor is important to consider as it directly affects the bass (low frequency) performance of the circuit. Speakers in wireless phones cannot usually respond well to low frequencies, so the corner frequency can be set to block low frequencies in this application. Equation Equation 3 is reconfigured to solve for the input coupling capacitance. 1 C + I 2p R f c I (3) If the corner frequency is within the audio band, the capacitors should have a tolerance of 10% or better, because any mismatch in capacitance causes an impedance mismatch at the corner frequency and below, and causes pop. Any capacitor in the audio path should have a rating of X7R or better. For a flat low-frequency response, use large input coupling capacitors (1 F). However, in a GSM phone the ground signal is fluctuating at 217 Hz, but the signal from the codec does not have the same 217 Hz fluctuation. The difference between the two signals is amplified, sent to the speaker, and heard as a 217 Hz hum. 12 Submit Documentation Feedback Copyright (c) 2002-2008, Texas Instruments Incorporated Product Folder Link(s): TPA2005D1 TPA2005D1 www.ti.com............................................................................................................................................................... SLOS369F - JULY 2002 - REVISED JULY 2008 SUMMING INPUT SIGNALS WITH THE TPA2005D1 Most wireless phones or PDAs need to sum signals at the audio power amplifier or just have two signal sources that need separate gain. The TPA2005D1 makes it easy to sum signals or use separate signal sources with different gains. Many phones now use the same speaker for the earpiece and ringer, where the wireless phone would require a much lower gain for the phone earpiece than for the ringer. PDAs and phones that have stereo headphones require summing of the right and left channels to output the stereo signal to the mono speaker. Summing Two Differential Input Signals Two extra resistors are needed for summing differential signals (a total of 5 components). The gain for each input source can be set independently (see equations Equation 4 and Equation 5, and Figure 35). V V Gain 1 + O + 2 150 kW V R V I1 I1 (4) V V Gain 2 + O + 2 150 kW V R V I2 I2 (5) If summing left and right inputs with a gain of 1 V/V, use RI1= RI2= 300 k. If summing a ring tone and a phone signal, set the ring-tone gain to Gain 2 = 2 V/V, and the phone gain to gain 1 = 0.1 V/V. The resistor values would be. . . * RI1 = 3 M, and = RI2 = 150 k. Differential Input 1 + RI1 - RI1 + RI2 To Battery Internal Oscillator Differential Input 2 RI2 CS IN- _ - VDD PWM H- Bridge VO+ VO- + IN+ GND Bias Circuitry SHUTDOWN Filter-Free Class D Figure 35. Application Schematic With TPA2005D1 Summing Two Differential Inputs Summing a Differential Input Signal and a Single-Ended Input Signal Figure 36 shows how to sum a differential input signal and a single-ended input signal. Ground noise can couple in through IN+ with this method. It is better to use differential inputs. The corner frequency of the single-ended input is set by CI2, shown in equation Equation 8. To assure that each input is balanced, the single-ended input must be driven by a low-impedance source even if the input is not in use. V V Gain 1 + O + 2 150 kW V R V I1 I1 (6) V V Gain 2 + O + 2 150 kW V R V I2 I2 (7) 1 C + I2 2p RI2 f c2 (8) Submit Documentation Feedback Copyright (c) 2002-2008, Texas Instruments Incorporated Product Folder Link(s): TPA2005D1 13 TPA2005D1 SLOS369F - JULY 2002 - REVISED JULY 2008............................................................................................................................................................... www.ti.com If summing a ring tone and a phone signal, the phone signal should use a differential input signal while the ring tone might be limited to a single-ended signal. Phone gain is set at gain 1 = 0.1 V/V, and the ring-tone gain is set to gain 2 = 2 V/V, the resistor values would be... * RI1 = 3 M, and = RI2 = 150 k. The high pass corner frequency of the single-ended input is set by CI2. If the desired corner frequency is less than 20 Hz. 1 C u I2 2p 150kW 20Hz (9) C I2 u 53pF (10) RI1 Differential Input 1 RI1 CI2 R I2 Single-Ended To Battery Internal Oscillator CS IN- Input 2 _ RI2 VDD PWM H- Bridge VO+ VO- + IN+ CI2 GND Bias Circuitry SHUTDOWN Filter-Free Class D Figure 36. Application Schematic With TPA2005D1 Summing Differential Input and Single-Ended Input Signals Summing Two Single-Ended Input Signals Four resistors and three capacitors are needed for summing single-ended input signals. The gain and corner frequencies (fc1 and fc2) for each input source can be set independently (see equations Equation 11 through Equation 14, and Figure 37). Resistor, RP, and capacitor, CP, are needed on the IN+ terminal to match the impedance on the IN- terminal. The single-ended inputs must be driven by low impedance sources even if one of the inputs is not outputting an ac signal. 14 Submit Documentation Feedback Copyright (c) 2002-2008, Texas Instruments Incorporated Product Folder Link(s): TPA2005D1 TPA2005D1 www.ti.com............................................................................................................................................................... SLOS369F - JULY 2002 - REVISED JULY 2008 V Gain 1 + V V Gain 2 + C C I1 I2 + + V O+2 I1 150 kW R I1 VV O+2 I2 1 150 kW R I2 VV (11) (12) 2p RI1 f c1 (13) 1 2p RI2 f c2 (14) C +C ) C P I1 I2 R R I2 R + I1 P R ) R I1 I2 (15) (16) Single-Ended Input 1 Single-Ended Input 2 CI1 R I1 To Battery CI2 R I2 Internal Oscillator CS IN- _ RP VDD PWM H- Bridge VO+ VO- + IN+ CP GND SHUTDOWN Bias Circuitry Filter-Free Class D Figure 37. Application Schematic With TPA2005D1 Summing Two Single-Ended Inputs EFFICIENCY AND THERMAL INFORMATION The maximum ambient temperature depends on the heat-sinking ability of the PCB system. The derating factor for the 2,5-mm x 2,5-mm MicroStar Junior package is shown in the dissipation rating table. Converting this to JA: 1 q + + 1 + 62.5CW JA 0.016 Derating Factor (17) Given JA of 62.5C/W, the maximum allowable junction temperature of 150C, and the maximum internal dissipation of 0.2 W (worst case 5-V supply), the maximum ambient temperature can be calculated with equation Equation 18. T Max + T Max * q P + 150 * 62.5 (0.2) + 137.5C A J JA Dmax (18) Equation Equation 18 shows that the calculated maximum ambient temperature is 137.5C at maximum power dissipation with a 5-V supply; however, the maximum ambient temperature of the package is limited to 85C. Because of the efficiency of the TPA2005D1, it can be operated under all conditions to an ambient temperature of 85C. The TPA2005D1 is designed with thermal protection that turns the device off when the junction temperature surpasses 150C to prevent damage to the IC. Also, using speakers more resistive than 8- dramatically increases the thermal performance by reducing the output current and increasing the efficiency of the amplifier. Submit Documentation Feedback Copyright (c) 2002-2008, Texas Instruments Incorporated Product Folder Link(s): TPA2005D1 15 TPA2005D1 SLOS369F - JULY 2002 - REVISED JULY 2008............................................................................................................................................................... www.ti.com BOARD LAYOUT Component Location Place all the external components close to the TPA2005D1. The input resistors need to be close to the TPA2005D1 input pins so noise does not couple on the high impedance nodes between the input resistors and the input amplifier of the TPA2005D1. Placing the decoupling capacitor, CS, close to the TPA2005D1 is important for the efficiency of the class-D amplifier. Any resistance or inductance in the trace between the device and the capacitor can cause a loss in efficiency. Trace Width Make the high current traces going to pins VDD, GND, VO+ and VO- of the TPA2005D1 have a minimum width of 0,7 mm. If these traces are too thin, the TPA2005D1's performance and output power will decrease. The input traces do not need to be wide, but do need to run side-by-side to enable common-mode noise cancellation. MicroStar JuniorTM BGA Layout Use the following MicroStar Junior BGA ball diameters: * 0,25 mm diameter solder mask * 0,28 mm diameter solder paste mask/stencil * 0,38 mm diameter copper trace Figure 38 shows how to lay out a board for the TPA2005D1 MicroStar Junior BGA. 0,28 mm SD 0,38 mm NC 0,25 mm GND GND Vo- GND VDD IN+ GND GND VDD IN- GND GND Vo+ Solder Mask Paste Mask Copper Trace Figure 38. TPA2005D1 MicroStar Junior BGA Board Layout (Top View) 16 Submit Documentation Feedback Copyright (c) 2002-2008, Texas Instruments Incorporated Product Folder Link(s): TPA2005D1 TPA2005D1 www.ti.com............................................................................................................................................................... SLOS369F - JULY 2002 - REVISED JULY 2008 ELIMINATING THE OUTPUT FILTER WITH THE TPA2005D1 This section focuses on why the user can eliminate the output filter with the TPA2005D1. Effect on Audio The class-D amplifier outputs a pulse-width modulated (PWM) square wave, which is the sum of the switching waveform and the amplified input audio signal. The human ear acts as a band-pass filter such that only the frequencies between approximately 20 Hz and 20 kHz are passed. The switching frequency components are much greater than 20 kHz, so the only signal heard is the amplified input audio signal. Traditional Class-D Modulation Scheme The traditional class-D modulation scheme, which is used in the TPA005Dxx family, has a differential output where each output is 180 degrees out of phase and changes from ground to the supply voltage, VDD. Therefore, the differential pre-filtered output varies between positive and negative VDD, where filtered 50% duty cycle yields 0 volts across the load. The traditional class-D modulation scheme with voltage and current waveforms is shown in Figure 39. Note that even at an average of 0 volts across the load (50% duty cycle), the current to the load is high causing a high loss and thus causing a high supply current. OUT+ OUT- +5 V Differential Voltage Across Load 0V -5 V Current Figure 39. Traditional Class-D Modulation Scheme's Output Voltage and Current Waveforms Into an Inductive Load With no Input TPA2005D1 Modulation Scheme The TPA2005D1 uses a modulation scheme that still has each output switching from 0 to the supply voltage. However, OUT+ and OUT- are now in phase with each other with no input. The duty cycle of OUT+ is greater than 50% and OUT- is less than 50% for positive voltages. The duty cycle of OUT+ is less than 50% and OUT- is greater than 50% for negative voltages. The voltage across the load sits at 0 volts throughout most of the switching period greatly reducing the switching current, which reduces any I2R losses in the load. Submit Documentation Feedback Copyright (c) 2002-2008, Texas Instruments Incorporated Product Folder Link(s): TPA2005D1 17 TPA2005D1 SLOS369F - JULY 2002 - REVISED JULY 2008............................................................................................................................................................... www.ti.com OUT+ OUT- Differential Voltage Across Load Output = 0 V +5 V 0V -5 V Current OUT+ OUT- Differential Voltage Output > 0 V +5 V 0V Across Load -5 V Current Figure 40. The TPA2005D1 Output Voltage and Current Waveforms Into an Inductive Load Efficiency: Why You Must Use a Filter With the Traditional Class-D Modulation Scheme The main reason that the traditional class-D amplifier needs an output filter is that the switching waveform results in maximum current flow. This causes more loss in the load, which causes lower efficiency. The ripple current is large for the traditional modulation scheme because the ripple current is proportional to voltage multiplied by the time at that voltage. The differential voltage swing is 2 x VDD and the time at each voltage is half the period for the traditional modulation scheme. An ideal LC filter is needed to store the ripple current from each half cycle for the next half cycle, while any resistance causes power dissipation. The speaker is both resistive and reactive, whereas an LC filter is almost purely reactive. The TPA2005D1 modulation scheme has little loss in the load without a filter because the pulses are short and the change in voltage is VDD instead of 2 x VDD. As the output power increases, the pulses widen making the ripple current larger. Ripple current could be filtered with an LC filter for increased efficiency, but for most applications the filter is not needed. An LC filter with a cutoff frequency less than the class-D switching frequency allows the switching current to flow through the filter instead of the load. The filter has less resistance than the speaker that results in less power dissipated, which increases efficiency. Effects of Applying a Square Wave Into a Speaker If the amplitude of a square wave is high enough and the frequency of the square wave is within the bandwidth of the speaker, a square wave could cause the voice coil to jump out of the air gap and/or scar the voice coil. A 250-kHz switching frequency, however, is not significant because the speaker cone movement is proportional to 1/f2 for frequencies beyond the audio band. Therefore, the amount of cone movement at the switching frequency is small. However, damage could occur to the speaker if the voice coil is not designed to handle the additional power. To size the speaker for added power, the ripple current dissipated in the load needs to be calculated by subtracting the theoretical supplied power, PSUP THEORETICAL, from the actual supply power, PSUP, at maximum output power, POUT. The switching power dissipated in the speaker is the inverse of the measured efficiency, MEASURED, minus the theoretical efficiency, THEORETICAL. 18 Submit Documentation Feedback Copyright (c) 2002-2008, Texas Instruments Incorporated Product Folder Link(s): TPA2005D1 TPA2005D1 www.ti.com............................................................................................................................................................... SLOS369F - JULY 2002 - REVISED JULY 2008 P -P (at max output power) SUP SUP THEORETICAL P P P + SUP - SUP THEORETICAL (at max output power) SPKR P P OUT OUT P SPKR SPKR +P +P (19) (20) 1 1 * (at max output power) OUT h MEASURED h THEORETICAL (21) R hTHEORETICAL + R L (at max output power) ) 2r L DS(on) (22) The maximum efficiency of the TPA2005D1 with a 3.6 V supply and an 8- load is 86% from equation Equation 22. Using equation Equation 21 with the efficiency at maximum power (84%), we see that there is an additional 17 mW dissipated in the speaker. The added power dissipated in the speaker is not an issue as long as it is taken into account when choosing the speaker. When to Use an Output Filter Design the TPA2005D1 without an output filter if the traces from amplifier to speaker are short. The TPA2005D1 passed FCC and CE radiated emissions with no shielding with speaker trace wires 100 mm long or less. Wireless handsets and PDAs are great applications for class-D without a filter. A ferrite bead filter can often be used if the design is failing radiated emissions without an LC filter, and the frequency sensitive circuit is greater than 1 MHz. This is good for circuits that just have to pass FCC and CE because FCC and CE only test radiated emissions greater than 30 MHz. If choosing a ferrite bead, choose one with high impedance at high frequencies, but low impedance at low frequencies. Use an LC output filter if there are low frequency (< 1 MHz) EMI sensitive circuits and/or there are long leads from amplifier to speaker. Figure 41 and Figure 42 show typical ferrite bead and LC output filters. Ferrite Chip Bead OUTP 1 nF Ferrite Chip Bead OUTN 1 nF Figure 41. Typical Ferrite Chip Bead Filter (Chip bead example: NEC/Tokin: N2012ZPS121) 33 H OUTP 1 F 33 H OUTN 1 F Figure 42. Typical LC Output Filter, Cutoff Frequency of 27 kHz Submit Documentation Feedback Copyright (c) 2002-2008, Texas Instruments Incorporated Product Folder Link(s): TPA2005D1 19 PACKAGE OPTION ADDENDUM www.ti.com 14-Oct-2011 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) Samples (Requires Login) TPA2005D1DGN ACTIVE MSOPPowerPAD DGN 8 80 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-1-260C-UNLIM TPA2005D1DGNG4 ACTIVE MSOPPowerPAD DGN 8 80 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-1-260C-UNLIM TPA2005D1DGNR ACTIVE MSOPPowerPAD DGN 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-1-260C-UNLIM TPA2005D1DGNRG4 ACTIVE MSOPPowerPAD DGN 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-1-260C-UNLIM TPA2005D1DRBR ACTIVE SON DRB 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPA2005D1DRBRG4 ACTIVE SON DRB 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPA2005D1GQYR ACTIVE BGA MICROSTAR JUNIOR GQY 15 2500 TBD SNPB Level-2-235C-1 YEAR TPA2005D1ZQYR ACTIVE BGA MICROSTAR JUNIOR ZQY 15 2500 Green (RoHS & no Sb/Br) SNAGCU Level-2-260C-1 YEAR TPA2005D1ZQYRG1 ACTIVE BGA MICROSTAR JUNIOR ZQY 15 2500 Green (RoHS & no Sb/Br) SNAGCU Level-2-260C-1 YEAR (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 14-Oct-2011 Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF TPA2005D1 : * Automotive: TPA2005D1-Q1 NOTE: Qualified Version Definitions: * Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant TPA2005D1DGNR MSOPPower PAD DGN 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 TPA2005D1DRBR SON DRB 8 3000 330.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2 TPA2005D1DRBR SON DRB 8 3000 330.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2 ZQY 15 2500 330.0 8.4 2.8 2.8 1.25 4.0 8.0 Q1 TPA2005D1ZQYR BGA MI CROSTA R JUNI OR Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TPA2005D1DGNR MSOP-PowerPAD DGN 8 2500 364.0 364.0 27.0 TPA2005D1DRBR SON DRB 8 3000 367.0 367.0 35.0 TPA2005D1DRBR SON DRB 8 3000 367.0 367.0 35.0 TPA2005D1ZQYR BGA MICROSTAR JUNIOR ZQY 15 2500 338.1 338.1 20.6 Pack Materials-Page 2 MECHANICAL DATA MPBG168B - SEPTEMBER 2000 - REVISED FEBRUARY 2002 GQY (S-PBGA-N15) PLASTIC BALL GRID ARRAY 1,50 TYP 2,60 SQ 2,40 0,50 0,25 D 0,50 C 1,50 TYP B 0,25 A 1 A1 Corner 2 3 4 Bottom View 0,77 0,71 1,00 MAX Seating Plane 0,35 0,25 0,05 M 0,25 0,15 0,08 4201436/D 01/02 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. MicroStar Junior configuration Falls within JEDEC MO-225 MicroStar Junior is a trademark of Texas Instruments. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated