HV9110 HV9112 HV9113 High-Voltage Current-Mode PWM Controller Ordering Information +VIN Min Max Feedback Accuracy Max Duty Cycle 20 Pin Plastic PLCC HV9110PJ Package Options 14 Pin Narrow Body SOIC HV9110NG HV9110X 10V 120V < 1% 49% 14 Pin Plastic DIP HV9110P 9.0V 80V 2% 49% HV9112P HV9112PJ HV9112NG HV9112X 10V 120V < 1% 99% HV9113P HV9113PJ HV9113NG HV9113X Die Standard temperature range for all parts is industrial (-40 to +85C). Features General Description 10 to 120V input range Current-mode control High efficiency Up to 1.0MHz internal oscillator The Supertex HV9110 through HV9113 are a series of BiCMOS/ DMOS single-output, pulse width modulator ICs intended for use in high-speed high-efficiency switchmode power supplies. They provide all the functions necessary to implement a single-switch current-mode PWM, in any topology, with a minimum of external parts. Internal start-up circuit Low internal noise Because they utilize Supertex's proprietary BiCMOS/DMOS technology, they require less than one tenth of the operating power of conventional bipolar PWM ICs, and can operate at more than twice their switching frequency. Dynamic range for regulation is also increased, to approximately 8 times that of similar bipolar parts. They start directly from any DC input voltages between 10 and 120VDC, requiring no external power resistor. The output stage is push-pull CMOS and thus requires no clamping diodes for protection, even when significant lead length exists between the output and the external MOSFET. The clock frequency is set with a single external resistor. Applications DC/DC converters Distributed power systems ISDN equipment PBX systems Modems Accessory functions are included to permit fast remote shutdown (latching or nonlatching) and undervoltage shutdown. For similar ICs intended to operate directly from up to 450VDC input, please consult the data sheet for the HV9120/9123. Absolute Maximum Ratings +VIN, Input Voltage HV9110/9113 HV9112 VDD, Logic Voltage Logic Linear Input, FB and Sense Input Voltage Storage Temperature Power Dissipation, SOIC 120V 80V 15.5V -0.3V to VDD+0.3V -65C to 150C 750mW Power Dissipation, Plastic DIP 1000mW Power Dissipation PLCC 1400mW For detailed circuit and application information, please refer to application notes AN-H13 and AN-H21 to AN-H24. 11/12/01 Supertex Inc. does not recommend the use of its products in life support applications and will not knowingly sell its products for use in such applications unless it receives an adequate "products liability indemnification insurance agreement." Supertex does not assume responsibility for use of devices described and limits its liability to the replacement of devices determined to be defective due to workmanship. No responsibility is assumed for possible omissions or inaccuracies. Circuitry and specifications are subject to change without notice. For the latest product specifications, refer to the Supertex website: http://www.supertex.com. For complete liability information on all Supertex products, refer to the most current databook or to the Legal/Disclaimer page on the Supertex website. 1 HV9110/HV9112/HV9113 Electrical Characteristics (Unless otherwise specified, VDD = 10V, +VIN = 48V, Discharge = -VIN = 0V, RBIAS = 390K, ROSC = 330K,TA = 25C.) Symbol Parameters Min Typ Max Unit Conditions HV9110/13 3.92 4.00 4.08 V RL = 10M HV9112 3.88 4.00 4.12 HV9110/13 3.82 4.00 4.16 Reference VREF Output Voltage RL = 10M, TA = -55C to 125C Impedance1 ZOUT Output ISHORT Short Circuit Current VREF 15 Change in VREF with Temperature1 30 45 K 125 250 A VREF = -VIN 0.25 mV/C TA = -55C to 125C MHz ROSC = 0 KHz ROSC = 330K Oscillator fMAX Oscillator Frequency 1.0 3.0 fOSC Accuracy2 80 100 120 160 200 240 Initial Voltage Stability Temperature 15 Coefficient1 170 ROSC = 150K % ppm/C 9.5V < VDD <13.5V TA = -55C to 125C PWM DMAX Maximum Duty Cycle1 HV9110/12 HV9113 Deadtime1 DMIN 49.0 49.4 49.6 95 97 99 HV9113 225 nsec Minimum Duty Cycle Minimum Pulse Width Before Pulse Drops Out1 % 0 % 80 125 nsec 1.2 1.4 V VFB = 0V 80 120 ns VSENSE = 1.5V, VCOMP 2.0V V VFB Shorted to Comp nA VFB = 4.0V Current Limit Maximum Input Signal td Delay to 1.0 Output1 Error Amplifier VFB Feedback Voltage IIN Input Bias Current VOS Input Offset Voltage AVOL GB Open Loop Voltage Unity Gain HV9110/13 3.96 4.00 4.04 HV9112 3.92 4.00 4.08 25 500 nulled during trim Gain1 Bandwidth1 except HV9111 60 80 dB 1.0 1.3 MHz see Fig. 1 Impedance1 ZOUT Output ISOURCE Output Source Current -1.4 -2.0 mA VFB = 3.4V ISINK Output Sink Current 0.12 0.15 mA VFB = 4.5V see Fig. 2 dB PSRR Power Supply Rejection1 Notes: 1. Guaranteed by design. Not subject to production test. 2. Stray capacitance on OSC In pin must be 5pF. 2 HV9110/HV9112/HV9113 Electrical Characteristics (continued) (Unless otherwise specified, VDD = 10V, +VIN = 48V, Discharge = -VIN = 0V, RBIAS = 390K, ROSC = 330K,TA = 25C.) Symbol Parameters Min Typ Max Unit Conditions HV9110/13 120 V IIN < 10A; VCC > 9.4V HV9112 80 10 A VDD > 9.4V IPREREG = 10A Pre-regulator/Startup +VIN Input Voltage +IIN Input Leakage Current VTH VDD Pre-regulator Turn-off Threshold Voltage 8.0 8.7 9.4 V VLOCK Undervoltage Lockout 7.0 8.1 8.9 V 1.0 mA CL < 75pF Shutdown = -VIN Supply IDD Supply Current 0.75 IQ Quiescent Supply Current 0.55 mA IBIAS Nominal Bias Current 20 A VDD Operating Range 9.0 13.5 V 100 ns Shutdown Logic tSD Shutdown Delay1 tSW Shutdown Pulse Width1 50 ns tRW RESET Pulse Width1 50 ns tLW Latching Pulse Width1 25 ns VIL Input Low Voltage VIH Input High Voltage IIH Input Current, Input Voltage High 1.0 5.0 A VIN = VDD IIL Input Current, Input Voltage Low -25 -35 A VIN = 0V V IOUT = 10mA 50 2.0 7.0 CL = 500pF, VSENSE = -VIN Shutdown and reset low V V Output VOH VOL ROUT tR tF Output High Voltage Output Low Voltage Output Resistance Rise Fall HV9110/13 VDD -0.25 HV9112 VDD -0.3 HV9110/13 VDD -0.3 IOUT = 10mA, TA = -55C to 125C All 0.2 HV9110/13 0.3 V IOUT = -10mA IOUT = -10mA, TA = -55C to 125C IOUT = 10mA IOUT = 10mA, Pull Up 15 25 Pull Down 8.0 20 Pull Up 20 30 Pull Down 10 30 30 75 ns CL = 500pF 20 75 ns CL = 500pF Time1 Time1 Note: 1. Guaranteed by design. Not subject to production test. 3 TA = -55C to 125C HV9110/HV9112/HV9113 Truth Table Shutdown Reset Output H H H HL L H Off, Not Latched L L Off, Latched LH L Off, Latched, No Change Normal Operation Normal Operation, No Change Shutdown Timing Waveforms 1.5V tF 10ns VDD tR 10ns 50% Sense 50% Shutdown 0 0 td t SD VDD Output VDD 90% Output 0 90% 0 t SW VDD 50% Shutdown tR, tF 10ns 50% 0 t LW VDD Reset 50% 50% 50% 0 t RW Functional Block Diagram FB COMP 14 (19) Discharge 13 (18) 9 (12) OSC In OSC Out 8 (11) 7 (10) Error Amplifier OSC - 10 (14) + VREF 2V Modulator Comparator - 4V 9113 + Current Sources Output 9110 9112 5 (8) Current Limit Comparator - 1 (20) 4 (6) Q S To Internal Circuits To V DD Q R + REF GEN BIAS T -V IN 1.2V 3 (5) Current Sense V DD 6 (9) VDD 2 (3) - +V IN 11 (16) Undervoltage Comparator Shutdown S Q 8.1V - + + Reset R 12 (17) 8.6V Pre-regulator/Startup Pin numbers in parentheses are for PLCC package 4 HV9110/HV9112/HV9113 Typical Performance Curves Fig. 1 Fig. 4 Error Amplifier Output Impedance (Z0) 1M 6 10 Output Switching Frequency vs. Oscillator Resistance 105 104 fOUT (Hz) HV9113 ZO () 3 10 2 10 100k HV9110, 9111, 9112 10 1 .1 1KHz 100KHz 10KHz 1MHz 10k 10k 10MHz 100 k Frequency ROSC () PSRR -- Error Amplifier and Reference Fig. 2 Fig. 5 0 80 -10 70 -20 Gain (dB) -30 PSSR (dB) 1M -40 -50 -60 -70 Error Amplifier Open Loop Gain/Phase 60 180 50 120 40 60 30 0 20 -60 10 -120 0 -180 -10 -80 10 100 1K 10K 100K 1M 100 1K 100K 10K 1M Frequency (Hz) Frequency (Hz) RDISCHARGE vs. tOFF (9113 only) 100 Fig. 6 104 ROSC = 100K VDD = 12V VDD = 10V tOFF (nsec) Bias Current (A) Fig. 3 10 103 ROSC = 10K ROSC = 1K 1 105 106 102 10-1 107 100 101 102 103 RDISCHARGE () Bias Resistance () 5 104 105 106 Phase (C) 100Hz HV9110/HV9112/HV9113 Test Circuits PSRR Error Amp ZOUT 0.1V swept 10Hz - 1MHz +10V (VDD) 1.0V swept 100Hz - 2.2MHz 100K1% 60.4K - (FB) Reference GND (-VIN) 100K1% 10.0V + V1 Tektronix P6021 (1 turn secondary) 4.00V V2 Reference 40.2K 0.1F V1 - + V2 0.1F NOTE: Set Feedback Voltage so that VCOMP = VDIVIDE 1mV before connecting transformer Detailed Description Preregulator the 50% maximum duty cycle versions, a frequency dividing flipflop. A single external resistor between the OSC In and OSC Out pins is required to set oscillator frequency (see graph). For the 50% maximum duty cycle versions the Discharge pin is internally connected to GND. For the 99% duty cycle version, the discharge pin can either be connected to VSS directly or connected to VSS through a resistor used to set a deadtime. The preregulator/startup circuit for the HV911X consists of a highvoltage n-channel depletion-mode DMOS transistor driven by an error amplifier to form a variable current path between the VIN terminal and the VDD terminal. Maximum current (about 20 mA) occurs when VDD = 0, with current reducing as VDD rises. This path shuts off altogether when VDD rises to somewhere between 7.8 and 9.4V, so that if VDD is held at 10 or 12V by an external source (generally the supply the chip is controlling). No current other than leakage is drawn through the high voltage transistor. This minimizes dissipation. One difference exists between the Supertex HV911X and competitive 911X's: On the Supertex part the oscillator is shut off when a shutoff command is received. This saves about 150A of quiescent current, which aids in the construction of power supplies to meet CCITT specification I-430, and in other situations where an absolute minimum of quiescent power dissipation is required. An external capacitor between VDD and VSS is generally required to store energy used by the chip in the time between shutoff of the high voltage path and the VDD supply's output rising enough to take over powering the chip. This capacitor should have a value of 100X or more the effective gate capacitance of the MOSFET being driven, i.e., Reference Cstorage 100 x (gate charge of FET at 10V / 10V) The Reference of the HV911X consists of a stable bandgap reference followed by a buffer amplifier which scales the voltage up to approximately 4.0V. The scaling resistors of the reference buffer amplifier are trimmed during manufacture so that the output of the error amplifier when connected in a gain of -1 configuration is as close to 4.000V as possible. This nulls out any input offset of the error amplifier. As a consequence, even though the observed reference voltage of a specific part may not be exactly 4.0V, the feedback voltage required for proper regulation will be. as well as very good high frequency characteristics. Stacked polyester or ceramic caps work well. Electrolytic capacitors are generally not suitable. A common resistor divider string is used to monitor VDD for both the undervoltage lockout circuit and the shutoff circuit of the high voltage FET. Setting the undervoltage sense point about 0.6V lower on the string than the FET shutoff point guarantees that the undervoltage lockout always releases before the FET shuts off. A 50K resistor is placed internally between the output of the reference buffer amplifier and the circuitry it feeds (reference output pin and non-inverting input to the error amplifier). This allows overriding the internal reference with a low-impedance voltage source 6.0V. Using an external reference reinstates the input offset voltage of the error amplifier, and its effect of the exact value of feedback voltage required. Bias Circuit An external bias resistor, connected between the bias pin and VSS is required by the HV911X to set currents in a series of current mirrors used by the analog sections of the chip. Nominal external bias current requirement is 15 to 20A, which can be set by a 390K to 510K resistor if a 10V VDD is used, or a 510k to 680K resistor if VDD will be 12V. A precision resistor is not required; 5% is fine. Because the reference of the 911X is a high impedance node, and usually there will be significant electrical noise near it, a bypass capacitor between the reference pin and VSS is strongly recommended. The reference buffer amplifier is intentionally compensated to be stable with a capacitive load of 0.01 to 0.1F. Clock Oscillator The clock oscillator of the HV911X consists of a ring of CMOS inverters, timing capacitors, a capacitor discharge FET, and, in 6 HV9110/HV9112/HV9113 Detailed Description (continued) Error Amplifier Remote Shutdown The error amplifier in the HV911X is a true low-power differential input operational amplifier intended for around-the-amplifier compensation. It is of mixed CMOS-bipolar construction: A PMOS input stage is used so the common-mode range includes ground and the input impedance is very high. This is followed by bipolar gain stages which provide high gain without the electrical noise of all-MOS amplifiers. The amplifier is unity-gain stable. The shutdown and reset pins of the 911X can be used to perform either latching or non-latching shutdown of a converter as required. These pins have internal current source pull-ups so they can be driven from open-drain logic. When not used they should be left open, or connected to VDD. Current Sense Comparators The output buffer of the HV911X is of standard CMOS construction (P-channel pull-up, N-channel pull-down). Thus the bodydrain diodes of the output stage can be used for spike clipping if necessary, and external Schottky diode clamping of the output is not required. Output Buffer The HV911X uses a true dual comparator system with independent comparators for modulation and current limiting. This allows the designer greater latitude in compensation design, as there are no clamps (except ESD protection) on the compensation pin. Like the error amplifier, the comparators are of low-noise BiCMOS construction. Sense 3 12 Reset Output 4 11 Shutdown -VIN 5 10 VREF VDD 6 9 Discharge OSC Out 7 8 OSC In 14 Pin SOIC/DIP Package VREF COMP 18 17 16 15 14 FB 19 13 NC BIAS 20 12 Discharge NC 1 11 OSC In NC 2 10 OSC Out +VIN 3 9 VDD * NC 4 5 6 7 8 -VIN 13 NC 2 NC +VIN Shutdown FB Output 14 Reset 1 Sense BIAS COMP Pinout 20-pin PJ Package top view 11/12/01 (c)2001 Supertex Inc. All rights reserved. Unauthorized use or reproduction prohibited. 7 1235 Bordeaux Drive, Sunnyvale, CA 94089 TEL: (408) 744-0100 * FAX: (408) 222-4895 www.supertex.com