IDT71V30S/L HIGH-SPEED 3.3V 1K X 8 DUAL-PORT STATIC RAM LEAD FINISH (SnPb) ARE IN EOL PROCESS - LAST TIME BUY EXPIRES JUNE 15, 2018 Features High-speed access - Commercial: 25/35/55ns (max.) - Industrial 35ns (max.) Low-power operation - IDT71V30S -- Active: 375mW (typ.) -- Standby: 5mW (typ.) - IDT71V30L -- Active: 375mW (typ.) -- Standby: 1mW (typ.) On-chip port arbitration logic Interrupt flags for port-to-port communication Fully asynchronous operation from either port Battery backup operation, 2V data retention (L Only) TTL-compatible, single 3.3V 0.3V power supply Industrial temperature range (-40OC to +85OC) is available for selected speeds Green parts available, see ordering information Functional Block Diagram OEL OER CEL CER R/WR R/WL I/O0R-I/O7R I/O0L- I/O7L I/O Control I/O Control (1) (1) BUSYL A9L A0L BUSYR Address Decoder MEMORY ARRAY 10 CEL OEL R/WL Address Decoder A9R A0R 10 ARBITRATION and INTERRUPT LOGIC (2) CER OER R/WR (2) INTL INTR 3741 drw 01 NOTES: 1. IDT71V30: BUSY outputs are non-tristatable push-pulls. 2. INT outputs are non-tristable push-pull output structure. DECEMBER 2017 1 (c)2017 Integrated Device Technology, Inc. DSC 3741/13 IDT71V30S/L High-Speed 1K x 8 Dual-Port Static RAM with Interrupts Industrial and Commercial Temperature Ranges Description The IDT71V30 is a high-speed 1K x 8 Dual-Port Static RAM. The IDT71V30 is designed to be used as a stand-alone 8-bit Dual-Port SRAM. Both devices provide two independent ports with separate control, address, and I/O pins that permit independent, asynchronous access for reads or writes to any location in memory. An automatic power down feature, controlled by CE, permits the on chip circuitry of each port to enter a very low standby power mode. Fabricated using CMOS high-performance technology, these devices typically operate on only 375mW of power. Low-power (L) versions offer battery backup data retention capability, with each DualPort typically consuming 200W from a 2V battery. The IDT71V30 devices are packaged in 64-pin STQFPs. N/C N/C N/C INTL BUSYL R/WL CEL VCC VCC CER R/WR BUSYR INTR N/C N/C N/C Pin Configurations(1,2,3) IDT71V30TF PP64(4) 64-Pin STQFP Top View(5) 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 I/O3L N/C I/O4L I/O5L I/O6L I/O7L N/C GND GND I/O0R I/O1R I/O2R I/O3R N/C I/O4R I/O5R OEL A0L A1L A2L A3L A4L A5L A6L N/C A7L A8L A9L N/C I/O0L I/O1L I/O2L 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 INDEX NOTES: 1. All VCC pins must be connected to the power supply. 2. All GND pins must be connected to the ground supply. 3. Package body is approximately 10mm x 10mm x 1.4mm. 4. This package code is used to reference the package diagram. 5. This text does not indicate the orientation of the actual part-marking. 6.42 2 OER A 0R A 1R A 2R A 3R A 4R A 5R A 6R N/C A 7R A 8R A 9R N/C N/C I/O 7R I/O 6R 3741 drw 03 IDT71V30S/L High-Speed 1K x 8 Dual-Port Static RAM with Interrupts Industrial and Commercial Temperature Ranges Recommended DC Operating Conditions Absolute Maximum Ratings(1) Symbol VTERM (2) TBIAS Rating Com'l & Ind Unit Terminal Voltage with Respect to GND -0.5 to +4.60 V Temperature Under Bias -55 to +125 Storage Temperature TSTG o -65 to +150 o Symbol C C Junction Temperature IOUT DC Output Current +150 o 50 C Capacitance (1) CIN COUT(3) Supply Voltage GND Ground VIH Input High Voltage Input Capacitance Output Capacitance Conditions(2) Max. Unit VIN = 3dV 9 pF VOUT = 3dV 10 pF Typ. Max. Unit 3.0 3.3 3.6 V 0 0 0 V 2.0 ____ VCC+0.3V V ____ 0.8 V (1) Input Low Voltage -0.3 3741 tbl 02 Maximum Operating Temperature and Supply Voltage(1,2) Ambient Temperature GND Vcc 0 C to +70 C 0V 3.3V + 0.3 -40 C to +85 C 0V 3.3V + 0.3 Grade Commercial O Industrial O O O NOTES: 1. This is the parameter TA. This is the "instant on" case temperature. 2. Industrial temperature: for specific speeds, packages and powers, contact your sales office. (TA = +25OC, f=1.0MHz) Parameter Min. NOTE: 1. VIL (min.) = -1.5V for pulse width less than 20ns. mA 3741 tbl 01 NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of the specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. VTERM must not exceed Vcc + 0.3V for more than 25% of the cycle time or 10ns maximum, and is limited to < 20mA for the period of VTERM > Vcc + 0.3V. 3. This is the absolute maximum junction temperature for the device. No DC Bias. Symbol VCC VIL TJN(3) Parameter 3741 tbl 03 3741 tbl 04 NOTES: 1. This parameter is determined by device characterization but is not production tested. 2. 3dv references the interpolated capacitance when the input and output signals switch from 0V to 3V or from 3V to 0V. DC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range (VCC = 3.3V 0.3V) 71V30S Symbol Parameter Test Conditions 71V30L Min. Max. Min. Max. Unit |ILI| Input Leakage Current(1) VCC = 3.6V, VIN = 0V to V CC ___ 10 ___ 5 A |ILO| Output Leakage Current CE = VIH, VOUT = 0V to V CC ___ 10 ___ 5 A VOL Output Low Voltage (I/O0-I/O7) IOL = 4mA ___ 0.4 ___ 0.4 V VOH Output High Voltage IOH = -4mA 2.4 ___ 2.4 ___ V 3741 tbl 05 NOTE: 1. At Vcc < 2.0V input leakages are undefined. Supply CurrentVIN > VCC -0.2V or < 0.2V 3 6.42 IDT71V30S/L High-Speed 1K x 8 Dual-Port Static RAM with Interrupts Industrial and Commercial Temperature Ranges DC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range(1,6,7) (VCC = 3.3V 0.3V) 71V30X25 Com'l Only Symbol Parameter ICC Dynamic Operating Current (Both Ports Active) ISB1 ISB2 ISB3 ISB4 Standby Current (Both Ports - TTL Level Inputs) Standby Current (One Port - TTL Level Inputs) Test Condition Version CEL and CER = V IL, Outputs Disabled f = fMAX(3) CEL and CER= V IL, f = fMAX(3) CE"A" = V IL and CE"B" = V IH(5) Active Port Outputs Disabled, f=fMAX(3) Full Standby Current (Both CEL and CER > V CC - 0.2V Ports - CMOS Level Inputs) V IN > V CC - 0.2V or V IN < 0.2V, f = 0(4) Full Standby Current (One Port - CMOS Level Inputs) CE"A" < 0.2V and CE"B" > V CC - 0.2V (5) V IN > V CC - 0.2V or V IN < 0.2V Active Port Outputs Disabled f=fMAX(3) 71V30X35 Com'l & Ind 71V30X55 Com'l Only Typ.(2) Max. Typ.(2) Max. Typ.(2) Max. Unit 75 75 145 115 75 75 135 105 mA COM'L S L 75 75 150 120 IND S L ___ ___ ___ ___ ___ ___ ___ ___ 75 145 ___ ___ COM'L S L 20 20 50 35 20 20 50 35 20 20 50 35 IND S L ___ ___ ___ ___ ___ ___ ___ ___ 20 50 ___ ___ COM'L S L 30 30 105 75 30 30 100 70 30 30 90 60 IND S L ___ ___ ___ ___ ___ ___ ___ ___ 30 100 ___ ___ COM'L S L 1.0 0.2 5.0 3.0 1.0 0.2 5.0 3.0 1.0 0.2 5.0 3.0 IND S L ___ ___ ___ ___ ___ ___ ___ ___ 1.0 5.0 ___ ___ COM'L S L 30 30 90 75 30 30 85 70 30 30 75 60 IND S L ___ ___ ___ ___ ___ ___ ___ ___ 30 85 ___ ___ mA mA mA mA 3741 tbl 06 NOTES: 1. 'X' in part number indicates power rating (S or L) 2. VCC = 3.3V, TA = +25C, and are not production tested. ICCDC = 70mA (Typ.) 3. At f = fMAX, address and control lines (except Output Enable) are cycling at the maximum frequency read cycle of 1/tRC. 4. f = 0 means no address or control lines change. 5. Port "A" may be either left or right port. Port "B" is the opposite from port "A". 6. Refer to chip enable Truth Table I. 7. Industrial temperature: for specific speeds, packages and powers contact your sales office. Data Retention Characteristics (L Version Only) 71V30L Symbol Parameter VDR VCC for Data Retention ICCDR Data Retention Current VCC = 2V, CE > VCC -0.2V tCDR(3) Chip Deselect to Data Retention Time tR(3) Operation Recovery Time Min. Typ. (1) Max. Unit 2.0 ____ ____ V Ind. ____ 100 1000 A Com'l. ____ 100 500 0 ____ ____ tRC(2) ____ ____ Test Condition VIN > VCC -0.2V or VIN < 0.2V NOTES: 1. VCC = 2V, TA = +25C, and is not production tested. 2. tRC = Read Cycle Time. 3. This parameter is guaranteed by device characterization but not production tested. 6.42 4 ns ns 3741 tbl 07 IDT71V30S/L High-Speed 1K x 8 Dual-Port Static RAM with Interrupts AC Test Conditions Industrial and Commercial Temperature Ranges Data Retention Waveform GND to 3.0V Input Pulse Levels DATA RETENTION MODE 3ns Max. Input Rise/Fall Times Input Timing Reference Levels 1.5V Output Reference Levels 1.5V VCC 3.0V 3741 tbl 08 tR VDR CE VIH VIH 3.3V 3741 drw 04 , 3.3V 590 DATA OUT BUSY INT 435 3.0V tCDR Figures 1 and 2 Output Load VDR 2.0V 590 DATA OUT 30pF 435 5pF 3741 drw 05 Figure 2. Output Test Load (For tHZ, tLZ, tWZ and tOW) * Including scope and jig. Figure 1. AC Output Test Load AC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range(3,4) 71V30X25 Com'l Only Symbol Parameter 71V30X35 Com'l & Ind 71V30X55 Com'l Only Min. Max. Min. Max. Min. Max. Unit READ CYCLE tRC Read Cycle Time 25 ____ 35 ____ 55 ____ ns tAA Address Access Time ____ 25 ____ 35 ____ 55 ns tACE Chip Enable Access Time ____ 25 ____ 35 ____ 55 ns tAOE Output Enable Access Time ____ 12 ____ 20 ____ 25 ns tOH Output Hold from Address Change 3 ____ 3 ____ 3 ____ ns 0 ____ 0 ____ 0 ____ ns ____ 12 ____ 15 ____ 30 ns 0 ____ 0 ____ 0 ____ ns ____ 50 ____ 50 ____ 50 ns (1,2) tLZ Output Low-Z Time tHZ Output High-Z Time(1,2) tPU Chip Enable to Power Up Time(2) tPD Chip Disable to Power Down Time (2) NOTES: 1. Transition is measured 0mV from Low- or High-impedance voltage with Output Test Load (Figure 2). 2. This parameter is guaranteed by device characterization, but is not production tested. 3. 'X' in part number indicates power rating (S or L). 4. Industrial temperature: for specific speeds, packages and power contact your sales office. 5 6.42 3741 tbl 09 IDT71V30S/L High-Speed 1K x 8 Dual-Port Static RAM with Interrupts Industrial and Commercial Temperature Ranges Timing Waveform of Read Cycle No. 1, Either Side(1) tRC ADDRESS tAA tOH tOH DATAOUT PREVIOUS DATA VALID DATA VALID BUSYOUT 3741 drw 06 tBDD (2,3) NOTES: 1. R/W = VIH, CE = VIL, and is OE = VIL. Address is valid prior to the coincidental with CE transition LOW. 2. tBDD delay is required only in case where the opposite is port is completing a write operation to same the address location. For simultaneous read operations BUSY has no relationship to valid output data. 3. Start of valid data depends on which timing becomes effective last tAOE, tACE, tAA, and tBDD. Timing Waveform of Read Cycle No. 2, Either Side(3) tACE CE tAOE (4) tHZ (2) OE tLZ (1) tHZ VALID DATA DATAOUT tLZ ICC CURRENT ISS (2) (1) tPD tPU 50% (4) 50% 3741 drw 07 NOTES: 1. Timing depends on which signal is asserted last, OE or CE. 2. Timing depends on which signal is desserted first, OE or CE. 3. R/W = VIH and the address is valid prior to or coincidental with CE transition LOW. 4. Start of valid data depends on which timing becomes effective last tAOE, tACE, and tBDD. 6.42 6 IDT71V30S/L High-Speed 1K x 8 Dual-Port Static RAM with Interrupts Industrial and Commercial Temperature Ranges AC Electrical Characteristics Over the Operating Temperature and Supply Voltage(4,5) 71V30X25 Com'l Only Symbol Parameter 71V30X35 Com'l & Ind 71V30X55 Com'l Only Min. Max. Min. Max. Min. Max. Unit WRITE CYCLE tWC Write Cycle Time 25 ____ 35 ____ 55 ____ ns tEW Chip Enable to End-of-Write 20 ____ 30 ____ 40 ____ ns tAW Address Valid to End-of-Write 20 ____ 30 ____ 40 ____ ns tAS Address Set-up Time 0 ____ 0 ____ 0 ____ ns tWP Write Pulse Width 20 ____ 30 ____ 40 ____ ns tWR Write Recovery Time 0 ____ 0 ____ 0 ____ ns tDW Data Valid to End-of-Write 12 ____ 20 ____ 20 ____ ns tHZ Output High-Z Time(1,2) ____ 12 ____ 15 ____ 30 ns tDH Data Hold Time(3) 0 ____ 0 ____ 0 ____ ns ____ 15 ____ 15 ____ 30 ns 0 ____ 0 ____ 0 ____ ns tWZ tOW Write Enable to Output in High-Z (1,2) (1,2,3) Output Active from End-of-Write 3741 tbl 10 NOTES: 1. Transition is measured 0mV from Low- or High-impedance voltage with Output Test Load (Figure 2). 2. This parameter is guaranteed by device characterization, but is not production tested. 3. The specification for tDH must be met by the device supplying write data to the SRAM under all operating conditions. Although tDH and tOW values will vary over voltage and temperature, the actual tDH will always be smaller than the actual tOW. 4. 'X' in part number indicates power rating (S or L). 5. Industrial temperatures: for specific speeds, packages and powers contact your sales office. 7 6.42 IDT71V30S/L High-Speed 1K x 8 Dual-Port Static RAM with Interrupts Industrial and Commercial Temperature Ranges Timing Waveform of Write Cycle No. 1,(R/W Controlled Timing)(1,5,8) tWC ADDRESS tHZ (7) OE tAW CE tWP(2) tAS (6) tHZ (7) tWR (3) R/W tWZ (7) DATA OUT tOW (4) (4) tDW tDH DATA IN 3741 drw 08 Timing Waveform of Write Cycle No. 2, CE Controlled Timing(1,5) tWC ADDRESS tAW CE tAS (6) tEW (2) tWR (3) R/W tDW tDH DATA IN 3741 drw 09 NOTES: 1. R/W or CE must be HIGH during all address transitions. 2. A write occurs during the overlap (tEW or tWP) of CE = VIL and R/W= VIL. 3. tWR is measured from the earlier of CE or R/W going HIGH to the end of the write cycle. 4. During this period, the l/O pins are in the output state and input signals must not be applied. 5. If the CE LOW transition occurs simultaneously with or after the R/W LOW transition, the outputs remain in the High-impedance state. 6. Timing depends on which enable signal (CE or R/W) is asserted last. 7. This parameter is determined be device characterization, but is not production tested. Transition is measured 0mV from steady state with the Output Test Load (Figure 2). 8. If OE is LOW during a R/W controlled write cycle, the write pulse width must be the larger of tWP or (tWZ + tDW) to allow the I/O drivers to turn off data to be placed on the bus for the required tDW. If OE is HIGH during a R/W controlled write cycle, this requirement does not apply and the write pulse can be as short as the specified tWP. 6.42 8 IDT71V30S/L High-Speed 1K x 8 Dual-Port Static RAM with Interrupts Industrial and Commercial Temperature Ranges AC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range(6,7) 71V30X25 Com'l Only Symbol Parameter 71V30X35 Com'l & Ind 71V30X55 Com'l Only Min. Max. Min. Max. Min. Max. Unit BUSY TIMING (M/S=VIH) tBAA BUSY Access Time from Address Match ____ 20 ____ 20 ____ 30 ns tBDA BUSY Disable Time from Address Not Matched ____ 20 ____ 20 ____ 30 ns tBAC BUSY Access Time from Chip Enable ____ 20 ____ 20 ____ 30 ns tBDC BUSY Disable Time from Chip Enable ____ 20 ____ 20 ____ 30 ns tWH Write Hold After BUSY(5) 20 ____ 30 ____ 40 ____ ns ____ 50 ____ 60 ____ 80 ns ____ 35 ____ 45 ____ 65 ns 5 ____ 5 ____ 5 ____ ns ____ 30 ____ 30 ____ 45 ns tWDD tDDD Write Pulse to Data Delay (1) Write Data Valid to Read Data Delay tAPS Arbitration Priority Set-up Time tBDD BUSY Disable to Valid Data(3) (1) (2) NOTES: 1. Port-to-port delay through SRAM cells from writing port to reading port, refer to "Timing Waveform of Write with Port-to-Port Read with BUSY". 2. To ensure that the earlier of the two ports wins. 3. tBDD is a calculated parameter and is the greater of 0, tWDD - tWP (actual) or tDDD - tDW (actual). 4. To ensure that the Write Cycle is inhibited on Port "B" during contention on Port "A". 5. To ensure that the Write Cycle is completed on Port "B" after contention on Port "A". 6. 'X' in part number indicates power rating (S or L). 7. Industrial temperature: for specific speeds, packages and powers contact your sales office. 3741 tbl 11 Timing Waveform of Write with Port-to-Port Read with BUSY(1,2,3,4) tWC ADDR"A" MATCH tWP R/W"A" tDW DATAIN"A" tDH VALID (1) tAPS ADDR"B" MATCH tBDD t BDA BUSY"B" tWDD DATAOUT"B" VALID tDDD 3741 drw 10 NOTES: 1. To ensure that the earlier of the two ports wins. 2. CEL = CER = VIL 3. OE = VIL for the reading port. 4. All timing is the same for the left and right ports. Port 'A' may be either the left or right port. Port "B" is opposite from port "A". 9 6.42 IDT71V30S/L High-Speed 1K x 8 Dual-Port Static RAM with Interrupts Industrial and Commercial Temperature Ranges Timing Waveform of Write with BUSY(3) tWP R/W'A' tWB BUSY'B' tWH (1) , R/W'B' (2) NOTES: 3741 drw 11 1. tWH must be met for BUSY. 2. BUSY is asserted on port 'B' blocking R/W'B', until BUSY'B' goes HIGH. 3. All timing is the same for the left and right ports. Port 'A' may be either the left or right port. Port "B" is opposite from port "A". Timing Waveform of BUSY Arbitration Controlled by CE Timing(1) ADDR 'A' AND 'B' ADDRESSES MATCH CE'B' tAPS (2) CE'A' tBAC tBDC BUSY'A' 3741 drw 12 NOTES: 1. All timing is the same for left and right ports. Port "A" may be either left or right port. Port "B" is the opposite from port "A". 2. If tAPS is not satisified, the BUSY will be asserted on one side or the other, but there is no guarantee on which side BUSY will be asserted. Timing Waveform of BUSY Arbitration Controlled Address Match Timing(1) tRC ADDR'A' OR tWC ADDRESSES MATCH tAPS ADDRESSES DO NOT MATCH (2) ADDR'B' tBAA tBDA BUSY'B' 3741 drw 13 NOTES: 1. All timing is the same for left and right ports. Port "A" may be either left or right port. Port "B" is the opposite from port "A". 2. If tAPS is not satisified, the BUSY will be asserted on one side or the other, but there is no guarantee on which side BUSY will be asserted. 6.42 10 IDT71V30S/L High-Speed 1K x 8 Dual-Port Static RAM with Interrupts Industrial and Commercial Temperature Ranges AC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range(1,2) 71V30X25 Com'l Only Symbol Parameter 71V30X35 Com'l & Ind 71V30X55 Com'l Only Min. Max. Min. Max. Min. Max. Unit INTERRUPT TIMING tAS Address Set-up Time 0 ____ 0 ____ 0 ____ ns tWR Write Recovery Time 0 ____ 0 ____ 0 ____ ns tINS Interrupt Set Time ____ 25 ____ 25 ____ 45 ns tINR Interrupt Reset Time ____ 25 ____ 25 ____ 45 ns 3741 tbl 12 NOTES: 1. 'X' in part number indicates power rating (S or L). 2. Industrial temperature: for specific speeds, packages and powers contact your sales office. Timing Waveform of Interrupt Mode(1) INT Sets tWC ADDR'A' INTERRUPT ADDRESS (2) tWR (4) tAS (3) R/W'A' tINS (3) INT'B' 3741 drw 14 INT Clears tRC ADDR'B' INTERRUPT CLEAR ADDRESS tAS (3) OE'B' tINR (3) INT'A' 3741 drw 15 NOTES:. 1. All timing is the same for left and right ports. Port "A" may be either left or right port. Port "B" is the opposite from port "A". 2. See Interrupt Truth Table II. 3. Timing depends on which enable signal (CE or R/W) is asserted last. 4. Timing depends on which enable signal (CE or R/W) is de-asserted first. 11 6.42 IDT71V30S/L High-Speed 1K x 8 Dual-Port Static RAM with Interrupts Industrial and Commercial Temperature Ranges Truth Tables Table I -- Non-Contention Read/Write Control(4) Left or Right Port (1) R/W CE OE D0-7 X H X Z Port Disab led and in Power-Down Mode, ISB2 or ISB4 X H X Z CER = CEL = VIH, Power-Down Mode, ISB1 or ISB3 L L X DATAIN H L L DATAOUT H L H Z Function Data on Port Written Into Memory (2) Data in Memory Output on Port(3) High Impedance Outputs 3741 tbl 13 NOTES: 1. A0L - A9L A0R - A9R. 2. If BUSY = L, data is not written. 3. If BUSY = L, data may not be valid, see tWDD and tDDD timing. 4. 'H' = VIH, 'L' = VIL, 'X' = DON'T CARE, 'Z' = HIGH IMPEDANCE Table II -- Interrupt Flag(1,4) Left Port Right Port R/WL CEL OEL A9L-A0L INTL R/WR CER OER A9R-A0R INTR L L X 3FF X X X X X L(2) Set Right INTR Flag X X X X X X L L 3FF H(3) Reset Right INTR Flag X X X X L(3) L L X 3FE X Set Left INTL Flag X L L 3FE H(2) X X X X X Reset Left INTL Flag 3741 tbl 14 NOTES: 1. Assumes BUSYL = BUSYR = VIH 2. If BUSYL = VIL, then No Change. 3. If BUSYR = VIL, then No Change. 4. 'H' = HIGH,' L' = LOW,' X' = DON'T CARE Table III -- Address BUSY Arbitration Inputs Function Outputs CEL CER AOL-A9L AOR-A9R BUSYL(1) BUSYR(1) Function X X NO MATCH H H Normal H X MATCH H H Normal X H MATCH H H Normal L L MATCH (2) (2) Write Inhibit(3) 3741 tbl 15 NOTES: 1. Pins BUSYL and BUSYR are both outputs for IDT71V30. BUSYX outputs on the IDT71V30 are non-tristatable push-pull. 2. 'L' if the inputs to the opposite port were stable prior to the address and enable inputs of this port. 'H' if the inputs to the opposite port became stable after the address and enable inputs of this port. If tAPS is not met, either BUSYL or BUSYR = LOW will result. BUSYL and BUSYR outputs can not be LOW simultaneously. 3. Writes to the left port are internally ignored when BUSYL outputs are driving LOW regardless of actual logic level on the pin. Writes to the right port are internally ignored when BUSYR outputs are driving LOW regardless of actual logic level on the pin. 6.42 12 IDT71V30S/L High-Speed 1K x 8 Dual-Port Static RAM with Interrupts Industrial and Commercial Temperature Ranges Functional Description The IDT71V30 provides two ports with separate control, address and I/O pins that permit independent access for reads or writes to any location in memory. The IDT71V30 has an automatic power down feature controlled by CE. The CE controls on-chip power down circuitry that permits the respective port to go into a standby mode when not selected (CE = VIH). When a port is enabled, access to the entire memory array is permitted. Interrupts If the user chooses the interrupt function, a memory location (mail box or message center) is assigned to each port. The left port interrupt flag (INTL) is asserted when the right port writes to memory location 3FE (HEX), where a write is defined as the CE = R/W = VIL per Truth Table II. The left port clears the interrupt by accessing address location 3FE access with CER = OER = VIL, R/W is a "don't care". Likewise, the right port interrupt flag (INTR) is asserted when the left port writes to memory location 3FF (HEX) and to clear the interrupt flag (INTR), the right port must access the memory location 3FF. The message (8 bits) at 3FE or 3FF is user-defined, since it is an addressable SRAM location. If the interrupt function is not used, address locations 3FE and 3FF are not used as mail boxes, and are part of the random access memory. Refer to Table II for the interrupt operation. Busy Logic Busy Logic provides a hardware indication that both ports of the SRAM have accessed the same location at the same time. It also allows one of the two accesses to proceed and signals the other side that the SRAM is "Busy". The BUSY pin can then be used to stall the access until the operation on the other side is completed. If a write operation has been attempted from the side that receives a BUSY indication, the write signal is gated internally to prevent the write from proceeding. The use of BUSY logic is not required or desirable for all applications. In some cases it may be useful to logically OR the BUSY outputs together and use any BUSY indication as an interrupt source to flag the event of an illegal or illogical operation. 13 6.42 IDT71V30S/L High-Speed 1K x 8 Dual-Port Static RAM with Interrupts Industrial and Commercial Temperature Ranges Ordering Information XXXXX A 99 A Device Type Power Speed Package A A A Process/ Temperature Range Blank 8 Tube or Tray Tape and Reel Blank I(1) Commercial (0C to +70C) Industrial (-40C to +85C) G(2) Green TF 64-pin STQFP (PP64) 25 35 55 Commercial Only Commercial & Industrial Commercial Only S L Standard Power Low Power 71V30 8K (1K x 8-Bit) Synchronous Dual-Port RAM Speed in nanoseconds 3741 drw 20 NOTES: 1. Industrial temperature range is available. For specific speeds, packages and powers contact your sales office. 2. Green parts available. For specific speeds, packages and powers contact your sales office. LEAD FINISH (SnPb) parts are in EOL process. Product Discontinuation Notice - PDN# SP-17-02 Datasheet Document History 12/9/98: 6/15/99: 8/3/99: 9/1/99: 11/12/99: 1/17/01: 3/14/05: 7/16/07: Initiated datasheet document history Converted to new format Cosmetic and typographical corrections Added additional notes to pin configurations Changed drawing format Page 2 Fixed typographical error Removed Preliminary Replaced IDT logo Pages 1 and 2 Moved all of "Description" to page 2 and adjusted page layouts Page 3 Increased storage temperature parameters Clarified TA parameter Page 4 DC Electrical parameters-changed wording from "open" to "disabled" Changed 200mV to 0mV in notes Page 1 Added green availability to features Page 17 Added green indicator to ordering information Page 1 & 17 Replaced old TM logo with new TM logo Page 3 Added Junction Temperature spec values to the Absolute Maximum Rating table Added footnote 3 for additional clarification of Junction Temperature 6.42 14 IDT71V30S/L High-Speed 1K x 8 Dual-Port Static RAM with Interrupts Industrial and Commercial Temperature Ranges Datasheet Document History (con't) 10/23/08: 11/25/09: 06/22/15: 07/23/15: 12/20/17: Page 14 Removed "IDT" from orderable part number Page 4 In order to correct the DC Chars table for the 71V30L35 speed grade and to the Data Retention Chars table, I Temp values have been added to each table respectively. In addition, all of the AC tables and the ordering information also now reflect this I temp correction Page 2 Removed IDT in reference to fabrication Page 2 & 14 The package code PP64-1 changed to PP64 to match standard package codes Page 14 Added Tape and Reel indicator to Ordering Information Entire datasheet Removed the 55ns Industrial speed offering. 55ns speed only offered in commercial grade Product Discontinuation Notice - PDN# SP-17-02 Last time buy expires June 15, 2018 CORPORATE HEADQUARTERS 6024 Silver Creek Valley Road San Jose, CA 95138 for SALES: 800-345-7015 or 408-284-8200 fax: 408-284-2775 www.idt.com The IDT logo is a registered trademark of Integrated Device Technology, Inc. 15 6.42 for Tech Support: 408-284-2794 DualPortHelp@idt.com