LM6152/LM6154 Dual and Quad High Speed/Low Power 75 MHz GBW Rail-to-Rail I/O Operational Amplifiers General Description Features Using patented circuit topologies, the LM6152/54 provides new levels of speed vs. power performance in applications where low voltage supplies or power limitations previously made compromise necessary. With only 1.4 mA/amplifier supply current, the 75 MHz gain bandwidth of this device supports new portable applications where higher power devices unacceptably drain battery life. The slew rate of the devices increases with increasing input differential voltage, thus allowing the device to handle capacitive loads while maintaining large signal amplitude. The LM6152/54 can be driven by voltages that exceed both power supply rails, thus eliminating concerns about exceeding the common-mode voltage range. The rail-to-rail output swing capability provides the maximum possible dynamic range at the output. This is particularly important when operating on low supply voltages. Operating on supplies from 2.7V to over 24V, the LM6152/54 is excellent for a very wide range of applications, from battery operated systems with large bandwidth requirements to high speed instrumentation. At VS = 5V, Typ unless noted n Greater than Rail-to-Rail Input CMVR -0.25V to 5.25V n Rail-to-Rail Output Swing 0.01V to 4.99V n Wide Gain-Bandwidth: 75 MHz @ 100 kHz n Slew Rate: Small signal 5V/s Large signal 45V/s n Low supply current 1.4mA/amplifier n Wide supply range 2.7V to 24V n Fast settling time of 1.1s for 2V step (to 0.01%) n PSRR 91 dB n CMRR 84 dB Applications n Portable high speed instrumentation n Signal conditioning amplifier/ADC buffers n Barcode scanners Connection Diagrams 8-Pin DIP/SO 14-Pin DIP/SO DS012350-3 Top View DS012350-4 Top View (c) 1999 National Semiconductor Corporation DS012350 www.national.com LM6152/LM6154Dual and Quad High Speed/Low Power 75 MHz GBW Rail-to-Rail I/O Operational Amplifiers May 1999 Ordering Information Packaged 8-Pin Dip 8-Pin SOIC 14-Pin DIP 14-Pin SOIC www.national.com Ordering Infomation NSC Drawing Number Supplied As Rails LM6152ACN, LM5152BCN N08E LM6152ACM, LM6152BCM M08A Rails LM6152ACMX, LM6152BCMX M08A 2.5k Tape and Reel Rails LM6154ACN, LM6154BCN N14A LM6154ACM, LM6154BCM M14A Rails LM6154ACMX, LM6154BCMX M14A 2.5k Tape and Reel 2 Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. ESD Tolerance (Note 2) 2500V Differential Input Voltage 15V Voltage at Input/Output Pin Storage Temperature Range -65C to +150C Junction Temperature (Note 4) 150C Operating Ratings (Note 1) 2.7V VS 24V Supply Voltage (V+) + 0.3V, (V-) -0.3V Supply Voltage (V+ - V-) Junction Temperature Range 35V Current at Input Pin 10mA Current at Output Pin (Note 3) 25mA Current at Power Supply Pin 50mA Lead Temperature (soldering, 10 sec) 260C 0C TJ + 70C LM6152,LM6154 Thermal Resistance (JA) N Pkg, 8-pin Molded Dip 115C/W M Pkg, 8-pin Surface Mount 193C/W N Pkg, 14-pin Molded Dip 81C/W M Pkg, 14-pin Surface Mount 126C/W 5.0V DC Electrical Characteristics Unless otherwise specified, all limits guaranteed for TJ = 25C, V+ = 5.0V, V- = 0V, VCM = VO = V+/2 and RL > 1 M to V+/2. Boldface limits apply at the temperature extremes. Symbol Parameter VOS Input Offset Voltage TCVOS Input Offset Voltage Average Drift IB Input Bias Current IOS Input Offset Current Conditions LM6154AC LM6152AC Limit (Note 6) LM6154BC LM6152BC Limt (Note 6) Units 2 4 5 7 mV max 500 750 980 1500 980 1500 nA max 32 40 100 160 100 160 nA max Typ (Note 5) 0.54 10 0V VCM 5V V/C RIN Input Resistance, CM 0V VCM 4V 30 CMRR Common Mode Rejection Ratio 0V VCM 4V 94 70 70 0V VCM 5V 84 60 60 M dB min PSRR Power Supply Rejection Ratio 5V V+ 24V 91 80 80 dB min VCM Input Common-Mode Voltage Range Low -0.25 0 0 V 5.25 5.0 5.0 V AV Large Signal Voltage Gain High RL = 10k 214 50 50 V/mV min VO Output Swing 0.006 0.02 0.03 0.02 0.03 V max 4.992 4.97 4.96 4.97 4.96 V min 0.04 0.10 0.12 0.10 0.12 V max 4.89 4.80 4.70 4.80 4.70 V min 3 2.5 3 2.5 mA min 27 17 27 17 mA max 7 5 7 5 mA min 40 40 mA max RL = 100k RL = 2k ISC Output Short Circuit Current Sourcing 6.2 Sinking 16.9 3 www.national.com 5.0V DC Electrical Characteristics (Continued) Unless otherwise specified, all limits guaranteed for TJ = 25C, V+ = 5.0V, V- = 0V, VCM = VO = V+/2 and RL > 1 M to V+/2. Boldface limits apply at the temperature extremes. Symbol IS Parameter Supply Current Conditions Per Amplifier Typ (Note 5) 1.4 LM6154AC LM6152AC Limit (Note 6) LM6154BC LM6152BC Limt (Note 6) Units 2 2.25 2 2.25 mA max 5.0V AC Electrical Characteristics Unless otherwise specified, all limits guaranteed for TJ = 25C, V+ = 5.0V, V- = 0V, VCM = VO = V+/2 and RL > 1 M to V+/2. Boldface limits apply at the temperature extremes. Symbol SR GBW Parameter Slew Rate Gain-Bandwidth Product Conditions 4V Step @ VS = 6V, RS < 1 k f = 100 kHz Typ (Note 5) 30 LM6154AC LM6152AC Limit (Note 6) LM6154BC LM6152BC Limt (Note 6) Units 24 15 24 15 V/s min 75 MHz en Input-Referred Voltage Noise RL = 10k f = 1 kHz in Input-Referred Current Noise f = 1 kHz 0.34 0.002 % 1.1 s Amp-to-Amp Isolation T.H.D Total Harmonic Distortion f = 10 kHz, RL = 10k ts Settling Time 2V Step to 0.01% 125 9 nV dB pA 2.7V DC Electrical Characteristics Unless otherwise specified, all limits guaranteed for TJ = 25C, V+ = 2.7V, V- = 0V, VCM = VO = V+/2 and RL > 1 M to V+/2. Boldface limits apply at the temperature extremes. Symbol Parameter VOS Input Offset Voltage Conditions Typ (Note 5) 0.8 LM6154AC LM6152AC Limit (Note 6) LM6154BC LM6152BC Limt (Note 6) Units 2 5 5 8 mV max TCVOS Input Offset Voltage Average Drift 10 V/C IB Input Bias Current 500 nA IOS Input Offset Current 50 nA RIN Input Resistance, CM 0V VCM 1.8V 30 M CMRR Common Mode Rejection Ratio 0V VCM 1.8V 88 0V VCM 2.7V 78 dB PSRR Power Supply Rejection Ratio 3V V 5V VCM Input Common-Mode Voltage Range Low -0.25 0 0 2.95 2.7 2.7 AV Large Signal Voltage Gain VO Output Swing High RL = 10k RL = 10k IS Supply Current www.national.com + 69 dB 5.5 Per Amplifier 4 V V V/mV 0.032 0.07 0.11 0.07 0.11 V max 2.68 2.64 2.62 2.64 2.62 V min 1.35 mA 2.7V AC Electrical Characteristics Unless otherwise specified, all limits guaranteed for TJ = 25C, V+ = 2.7V, V- = 0V, VCM = VO = V+/2 and RL > 1 M to V+/2. Boldface limits apply at the temperature extremes. Symbol GBW Parameter Gain-Bandwidth Product Conditions f = 100kHz Typ (Note 5) LM6154AC LM6152AC Limit (Note 6) LM6154BC LM6152BC Limt (Note 6) 80 Units MHz 24V DC Electrical Characteristics Unless otherwise specified, all limits guaranteed for TJ = 25C, V+ = 24V, V- = 0V, VCM = VO = V+/2 and RL > 1 M to V+/2. Boldface limits apply at the temperature extremes. Symbol Parameter VOS Input Offset Voltage Conditions Typ (Note 5) 0.3 LM6154AC LM6152AC Limit (Note 6) LM6154BC LM6152BC Limt (Note 6) Units 2 4 7 9 mV max TCVOS Input Offset Voltage Average Drift 10 V/C IB Input Bias Current 500 nA IOS Input Offset Current 32 nA RIN Input Resistance, CM 0V VCM 23V 60 Meg CMRR Common Mode Rejection Ratio 0V VCM 23V 94 0V VCM 24V 84 dB PSRR Power Supply Rejection Ratio 0V VCM 24V VCM Input Common-Mode Voltage Range Low -0.25 0 0 24.25 24 24 AV Large Signal Voltage Gain VO Output Swing High RL = 10k RL = 10k Supply Current IS 95 dB V V 55 Per Amplifier V/mV 0.044 0.075 0.090 0.075 0.090 V max 23.91 23.8 23.7 23.8 23.7 V min 1.6 2.25 2.50 2.25 2.50 mA max 24V AC Electrical Characteristics Unless otherwise specified, all limits guaranteed for TJ = 25C, V+ = 24V, V- = 0V, VCM = VO = V+/2 and RL > 1 M to V+/2. Boldface limits apply at the temperature extremes. Symbol GBW Parameter Gain-Bandwidth Product Conditions f = 100kHz Typ (Note 5) 80 LM6154AC LM6152AC Limit (Note 6) LM6154BC LM6152BC Limt (Note 6) Units MHz Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics. Note 2: Human body model, 1.5k in series with 100pF. Note 3: Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in exceeding the maximum allowed junction temperature of 150C. Note 4: The maximum power dissipation is a function of TJ(max) , JA, and TA. The maximum allowable power dissipation at any ambient temperature is PD = (TJ(max)-T A)/JA. All numbers apply for packages soldered directly into a PC board. Note 5: Typical Values represent the most likely parametric norm. Note 6: All limits are guaranteed by testing or statistical analysis. 5 www.national.com Typical Performance Characteristics Supply Current vs. Supply Voltage Offset Voltage vs. Supply voltage DS012350-5 Bias Current vs. VCM DS012350-6 Bias Current vs. VCM DS012350-8 Output Voltage vs. Source Current DS012350-9 Output Voltage vs. Source Current DS012350-11 Output Voltage vs. Sink Current DS012350-12 Output Voltage vs. Sink Current DS012350-14 www.national.com DS012350-15 6 Bias Current vs. Supply voltage DS012350-7 Bias Current vs. VCM DS012350-10 Output Voltage vs. Source Current DS012350-13 Output Voltage vs. Sink Current DS012350-16 Typical Performance Characteristics Crosstalk (dB vs. Frequency (Continued) GBWP (@ 100 kHz) vs. Supply Voltage DS012350-17 Unity Gain Frequency vs. Supply Voltage for Various Loads DS012350-18 DS012350-19 CMRR Voltage Swing vs. Frequency (CL = 100 pF) DS012350-20 PSRR vs. Frequency DS012350-23 DS012350-22 Open Loop Gain/ Phase (VS = 5V) Open Loop Gain/ Phase (VS = 10V) DS012350-24 Noise Voltage vs. Frequency DS012350-25 Noise Current vs. Frequency DS012350-27 DS012350-28 7 Open Loop Gain/ Phase (VS = 24V) DS012350-26 Voltage Error vs. Settle Time DS012350-29 www.national.com Typical Performance Characteristics (Continued) Because of the unique structure of this amplifier, when used at low closed loop gains, the realizable BW will be much less than the GBW product would suggest. The LM6152/6154 brings a new level of ease of use to op amp system design. The greater than rail-to-rail input voltage range eliminates concern over exceeding the common-mode voltage range. The rail-to-rail output swing provides the maximum possible dynamic range at the output. This is particularly important when operating on low supply voltages. Total Harmonic Distortion vs. Frequency The high gain-bandwidth with low supply current opens new battery powered applications where higher power consumption previously reduced battery life to unacceptable levels. The ability to drive large capacitive loads without oscillating functional removes this common problem. To take advantage of these features, some ideas should be kept in mind. The LM6152/6154, capacitive loads do not lead to oscillations, in all but the most extreme conditions, but they will result in reduced bandwidth. They also cause increased settling time. Unlike most bipolar op amps, the unique phase reversal prevention/speed-up circuit in the input stage, caused the slew rate to be very much a function of the input pulse amplitude. This results in a 10 to 1 increase in slew rate when the differential input signal increases. Large fast pulses will raise the slew-rate to more than 30V/s. DS012350-31 Application Information The LM6152/6154 is ideally suited for operation with about 10k (Feedback Resistor, RF) between the output and the negative input terminal. With RF set to this value, for most applications requiring a close loop gain of 10 or less, an additional small compensation capacitor (CF) (see Figure 1) is recommended across RF in order to achieve a reasonable overshoot (10%) at the output by compensating for stray capacitance across the inputs. The optimum value for CF can best be established experimentally with a trimmer cap in place since its value is dependant on the supply voltage, output driving load, and the operating gain. Below, some typical values used in an inverting configuration and driving a 10k load have been tabulated for reference: TABLE 1. Typical BW (-3 dB) at Various Supply Voltage and Gains VS Volts 3 24 Gain CF pF BW (-3 dB) MHz -1 5.6 4 DS012350-21 -10 6.8 1.97 FIGURE 2. Slew Rate vs. Vdiff -100 None 0.797 -1 2.2 6.6 The speed-up action adds stability to the system when driving large capacitive loads. A conventional op amp exhibits a fixed maximum slew-rate even though the differential input voltage rises due to the lagging output voltage. In the LM6152/6154, increasing lag causes the differential input voltage to increase but as it does, the increased slew-rate keeps the output following the input much better. This effectively reduces phase lag. As a result, the LM6152/6154 can drive capacitive loads as large as 470 pF at gain of 2 and above, and not oscillate. -10 4.7 2.2 -100 None 0.962 In the non-inverting configuration, the LM6152/6154 can be used for closed loop gains of +2 and above. In this case, also, the compensation capacitor (CF) is recommended across RF ( = 10 k) for gains of 10 or less. Capacitive loads decrease the phase margin of all op amps. This can lead to overshoot, ringing and oscillation. This is caused by the output resistance of the amplifier and the load capacitance forming an R-C phase shift network. The LM6152/6154 senses this phase shift and partly compensates for this effect. DS012350-30 FIGURE 1. Typical Inverting Gain Circuit AV = -1 www.national.com 8 Physical Dimensions inches (millimeters) unless otherwise noted 8-Lead (0.150") Molded Small Outline Package, JEDEC Ordering Number LM6152ACM or LM7162BCM NSC Package Number M08A 14-Lead (0.150") Molded Small Outline Package, JEDEC Order Number LM6154ACM or LM6154BCM NSC Package Number M14A 9 www.national.com Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 8-Lead (0.300" Wide) Molded Dual-In-Line Package, JEDEC Order Number LM615ACN or LM6152BCN NSC Package Number N08E www.national.com 10 inches (millimeters) unless otherwise noted (Continued) 14-Lead (0.300" Wide) Molded Dual-In-Line Package, JEDEC Order Number LM6154ACN or LM6154BCN NSC Package Number N14A LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: support@nsc.com www.national.com National Semiconductor Europe Fax: +49 (0) 1 80-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 1 80-530 85 85 English Tel: +49 (0) 1 80-532 78 32 Francais Tel: +49 (0) 1 80-532 93 58 Italiano Tel: +49 (0) 1 80-534 16 80 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: sea.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. LM6152/LM6154Dual and Quad High Speed/Low Power 75 MHz GBW Rail-to-Rail I/O Operational Amplifiers Physical Dimensions