LTC4413-1/LTC4413-2 Dual 2.6A, 2.5V to 5.5V Fast Ideal Diodes in 3mm x 3mm DFN Description Features n n n n n n n n n n n n n n 2-Channel Ideal Diode OR'ing or Load Sharing Low Loss Replacement for PowerPathTM OR'ing Diodes Fast Response Replacement for LTC4413 Low Forward On-Resistance (140m Max at 3.6V) Low Reverse Leakage Current Low Regulated Forward Voltage (18mV Typ) Overvoltage Protection Sensor with Drive Output for an External P-Channel MOSFET (LTC4413-2 Only) 2.5V to 5.5V Operating Range 2.6A Maximum Forward Current Internal Current Limit Protection Internal Thermal Protection Status Output to Indicate if Selected Channel is Conducting Programmable Channel On/Off Low Profile (0.75mm) 10-Lead 3mm x 3mm DFN Package Applications n n n n n Battery and Wall Adapter Diode OR'ing in Handheld Products Backup Battery Diode OR'ing Power Switching USB Peripherals Uninterruptable Supplies The LTC(R)4413-1 and LTC4413-2 each contain two monolithic ideal diodes, each capable of supplying up to 2.6A from input voltages between 2.5V and 5.5V. The ideal diodes use a 100m P-channel MOSFET to independently connect INA to OUTA and INB to OUTB. During normal forward operation, the voltage drops across each of these diodes are regulated to as low as 18mV. Quiescent current is less than 80A for diode currents up to 1A. If either of the output voltages exceeds its respective input voltage, that MOSFET is turned off and less than 1A of reverse current flows from OUT to IN. Maximum forward current in each MOSFET is limited to a constant 2.6A and internal thermal limiting circuits protect the part during fault conditions. An internal overvoltage protection sensor detects when a voltage exceeds the LTC4413-2 absolute maximum voltage tolerance. Two active-high control pins independently turn off the two ideal diodes contained within the LTC4413-1/LTC44132. When the selected channel is reverse biased, or the LTC4413-1/LTC4413-2 is put into low power standby, the status signal is pulled low by an 11A open drain. The LTC4413-1/LTC4413-2 are housed in a 10-lead 3mm x 3mm DFN package. L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks and ThinSOT and PowerPath are trademarks of Analog Devices, Inc. All other trademarks are the property of their respective owners. Typical Application Power Loss vs Load Automatic Switchover from a Battery to a Wall Adapter OUTA INA 10F 0.1F 1 BAT + VCC 600 470k IDEAL ENBA STAT LTC4413-2 OVI GND STAT OVP OVP OUTB ENBB INB TO LOAD 4.7F IDEAL 441312 TA01a STAT IS HIGH WHEN WALL ADAPTER IS SUPPLYING LOAD CURRENT OVP IS HIGH WHEN WALL ADAPTER VOLTAGE > 6V POWER LOSS (mW) FDR8508 WALL ADAPTER INPUT 700 500 LTC4413-1 400 300 1N5817 200 100 0 0 500 1000 1500 2000 LOAD (mA) 2500 3000 441312 TA01b 441312fg For more information www.linear.com/LTC4413-1 1 LTC4413-1/LTC4413-2 Absolute Maximum Ratings (Note 1) INA, INB, OUTA, OUTB, STAT, ENBA, ENBB Voltage..................................... -0.3V to 6V OVI, OVP Voltage.........................................-0.3V to 13V Operating Temperature Range..................-40C to 85C Storage Temperature Range................... -65C to 125C Continuous Power Dissipation...........................1500mW (Derate 25mW/C Above 70C) Pin Configuration LTC4413-1 LTC4413-2 TOP VIEW TOP VIEW INA 1 10 OUTA INA 1 ENBA 2 9 STAT ENBA 2 GND 3 8 NC GND 3 ENBB 4 7 NC ENBB 4 7 OVP INB 5 6 OUTB INB 5 6 OUTB 11 DD PACKAGE 10-LEAD (3mm x 3mm) PLASTIC DFN TJMAX = 125C, JA = 43C/W EXPOSED PAD (PIN 11) IS SGND, MUST BE SOLDERED TO PCB Order Information LEAD FREE FINISH TAPE AND REEL 10 OUTA 9 STAT 11 8 OVI DD PACKAGE 10-LEAD (3mm x 3mm) PLASTIC DFN TJMAX = 125C, JA = 43C/W EXPOSED PAD (PIN 11) IS SGND, MUST BE SOLDERED TO PCB http://www.linear.com/product/LTC4413-1#orderinfo PART MARKING PACKAGE DESCRIPTION TEMPERATURE RANGE LTC4413EDD-1#PBF LTC4413EDD-1#TRPBF LCPP 10-Lead (3mm x 3mm) Plastic DFN -40C to 85C LTC4413EDD-2#PBF LTC4413EDD-2#TRPBF LCPQ 10-Lead (3mm x 3mm) Plastic DFN -40C to 85C LEAD BASED FINISH TAPE AND REEL PART MARKING PACKAGE DESCRIPTION TEMPERATURE RANGE LTC4413EDD-1 LTC4413EDD-1#TR LCPP 10-Lead (3mm x 3mm) Plastic DFN -40C to 85C LTC4413EDD-2 LTC4413EDD-2#TR LCPQ 10-Lead (3mm x 3mm) Plastic DFN -40C to 85C Consult LTC Marketing for parts specified with wider operating temperature ranges. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/. Some packages are available in 500 unit reels through designated sales channels with #TRMPBF suffix. 441312fg 2 For more information www.linear.com/LTC4413-1 LTC4413-1/LTC4413-2 Electrical Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Notes 2, 6) SYMBOL PARAMETER CONDITIONS VIN, VOUT Operating Supply Range for Channel A or B VIN and/or VOUT Must be in This Range for Proper Operation l MIN UVLO UVLO Turn-On Rising Threshold Max (VINA, VINB, VOUTA, VOUTB) l UVLO Turn-Off Falling Threshold Max (VINA, VINB, VOUTA, VOUTB) l IQF Quiescent Current in Forward Regulation, VINA = 3.6V, IINA = 100mA, VINB = 0V, Measured via GND IINB = 0mA (Note 3) l IQRIN Current Drawn from or Sourced into IN When VOUT is Greater than VIN VIN = 3.6V, VOUT = 5.5V (Note 6) l IQRGND Quiescent Current While in Reverse Turn-Off, Measured via GND VINA = VINB = 0V, VOUTB = VOUTA = 5.5V, VSTAT = 0V IQROUTB Quiescent Current While in Reverse Turn-Off. Current Drawn from VOUTA When OUTB Supplies Chip Power VINA = VINB = 0V, VOUTA = 3.6V, VOUTB = 5.5V IQOFF Quiescent Current with Both ENBA and ENBB High VRTO TYP 2.5 MAX UNITS 5.5 V 2.45 V 1.7 V 40 58 A 2.5 4.5 A 28 36 A l 3.5 6.5 A VINA = VINB = 3.6V, VENBA = VENBB = 1V l 28 38 A Reverse Turn-Off Voltage (VOUT - VIN) VIN = 3.6V l 10 mV VFWD Forward Voltage Drop (VIN - VOUT) at IOUT = -1mA VIN = 3.6V l 18 24 mV RFWD On-Resistance, RFWD Regulation (Measured as V/I) VIN = 3.6V, IOUT = -100mA to -500mA (Note 5) 100 140 m RON On-Resistance, RON Regulation (Measured as V/I at IIN = 1A) VIN = 3.6V, IIN = 1A (Note 5) 140 200 m tON PowerPath Turn-On Time VIN = 3.6V, from ENBA, ENBB Falling to IOUT Ramp Starting 11 s tOFF PowerPath Turn-Off Time VIN = 3.6V, from ENBA, ENBB Rising with IIN = 100mA Falling to 0mA 2 s -1 -5 Short-Circuit Response IOC Current Limit VINA OR B = 3.6V (Note 5) 1.8 A IQOC Quiescent Current While in Overcurrent Operation VINA OR B = 3.6V, IOUT = 1.8A (Note 5) ISOFF STAT Off Current Shut Down l ISON STAT Sink Current VIN > VOUT, VENB > VENBIH, TJ < 135C, IOUT < IMAX l tS(ON) STAT Pin Current Turn-On Time VIN = 3.6V, from ENBA, ENBB Falling 1.8 s tS(OFF) STAT Pin Current Turn-Off Time VIN = 3.6V, from ENBA, ENBB Rising 0.8 s VENBIH ENB Inputs Rising Threshold Voltage VENBA, VENBB Rising l VENBIL ENB Inputs Falling Threshold Voltage VENBA, VENBB Falling l VENBHYST ENB Input Hysteresis VENBHYST = (VENBIH - VENBIL) IENB ENB Inputs Pull-Down Current VOUT < VIN = 3.6V, VENBA < VENBIL, VENBB < VENBIL 100 130 A -1 0 1 A 7 11 15 A STAT Output ENB Inputs l 540 400 2 600 mV 460 mV 90 mV 3 4 A 441312fg For more information www.linear.com/LTC4413-1 3 LTC4413-1/LTC4413-2 Electrical Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Notes 2, 6) SYMBOL PARAMETER CONDITIONS MIN TYP MAX 5.9 6.2 UNITS OVI Input (LTC4413-2 Only) VOVIH OVI Input Rising Threshold Voltage VOVI Rising VOVIL OVI Input Falling Threshold Voltage VOVI Falling VOVID OVI-OVP Voltage Drop IOVI OVI Bias Current 5.6 V VOVI = 8V, No Load at OVP 100 mV VOVI = 8V 80 A Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LTC4413-1/LTC4413-2 are guaranteed to meet performance specifications from 0C to 85C. Specifications over the -40C to 85C operating temperature range are assured by design, characterization and correlation with statistical process controls. Note 3: Quiescent current increases with diode current: refer to plot of IQF vs IOUT. 5.4 V Note 4: This IC includes overtemperature protection that is intended to protect the device during momentary overload conditions. Overtemperature protection will become active at a junction temperature greater than the maximum operating temperature. Continuous operation above the specified maximum operating junction temperature may impair device reliability. Note 5: Specification is guaranteed by correlation to wafer-level measurements. Note 6: Unless otherwise specified, current into a pin is positive and current out of a pin is negative. All voltages referenced to GND. 441312fg 4 For more information www.linear.com/LTC4413-1 LTC4413-1/LTC4413-2 Typical Performance Characteristics IQF vs ILOAD (Log) 120 120C 120 80C 40C 40C 0C -40C 60 1A 80 -40C 60 40 40 20 20 20 10 1 100 LOAD (mA) 0 10000 1000 0 1000 1500 2000 LOAD (mA) 500 2500 441312 G01 2.20 3000 2.15 2500 IOC (mA) 2000 40 30 1500 1000 20 500 10 2 2.5 3 3.5 4 4.5 5 5.5 0 VIN (V) 40 80 120 1.85 -40 ENBIH/ENBIL (mV) 100 50 ENBIH ENBIL 400 300 200 441312 G07 0 -40 120 ENBA, ENBB Hysteresis vs Temperature 100 100 120 80 120 500 200 150 40 441312 G06 600 20 40 60 80 TEMPERATURE (C) 0 TEMPERATURE (C) ENBA, ENBB Thresholds vs Temperature 250 0 FALLING 1.95 441312 G05 UVLO Hysteresis vs Temperature UVLO HYSTERESIS (mV) 2.00 TEMPERATURE (C) 441312 G04 0 -40 -20 2.05 1.90 0 -40 6 120 RISING 2.10 ENBA, ENBB HYSETERSIS (mV) 0 40 80 TEMPERATURE (C) UVLO Thresholds vs Temperature 3500 60 IQF = 100mA 0 441312 G03 UVLO THRESHOLDS (V) IQF = 1A 50 1mA 0 -40 3000 IOC vs Temperature IQF vs VIN 70 100mA 441312 G02 90 80 500mA 60 40 0 IQF (A) 100 0C 80 IQF (A) IQF (A) 80 IQF vs Temperature 120C 100 80C 100 IQF vs ILOAD (Linear) IQF (A) 120 0 40 80 TEMPERATURE (C) 120 441312 G08 100 80 60 40 20 0 -40 -20 0 20 40 60 80 TEMPERATURE (C) 100 120 441312 G09 441312fg For more information www.linear.com/LTC4413-1 5 LTC4413-1/LTC4413-2 Typical Performance Characteristics RFWD vs VIN and ILOAD = 500mA 500 VFWD and RFWD vs ILOAD (Linear) 120C 80C 40C 0C -40C 78 76 400 RFWD (m) 68 VFWD 400 300 150 200 100 RFWD 64 100 50 62 2 2.5 3 3.5 4 4.5 VIN (V) 5 5.5 6 0 0 500 1000 1500 2000 LOAD (mA) 2500 200 100 100 50 10 1 100 LOAD (mA) 1 100 80 100 1A 60 ILEAK vs Temperature at VREVERSE = 5.5V 0.1 100mA 150 0 10000 1000 441312 G12 120 120C 80C 40C 0C -40C RFWD (m) VFWD (mV) 150 RFWD vs Temperature VFWD vs ILOAD (Log) 200 200 VFWD 300 0 0 3000 250 441312 G11 441312 G10 250 RFWD 500mA ILEAK (A) 60 300 120C 80C 40C 0C -40C 500 200 66 RFWD and VFWD vs ILOAD (Log) VFWD (mV) 70 600 VFWD (mV) RFWD 500mA (m) 74 72 250 RFWD (m) 80 5.5V 0.01 3.6V 0.001 40 50 0 0.0001 20 10 1 100 LOAD (mA) 1000 10000 0 -40 0 40 80 TEMPERATURE (C) 441312 G13 100 120C 80C 40C 0C -40C ILEAK (A) 1 0.00001 -40 -20 0 20 40 60 80 TEMPERATURE (C) CH1 = IN 100mV/DIV ENBA, ENBB Turn-On, 30s to Turn On with 180mA Load CH1 INA, INB 1V/DIV CH2 OUT 100mV/DIV 100 120 441312 G15 441312 G14 Response to 800mA Load Step in <16s ILEAK vs VREVERSE 10 120 CH3 ENBA, ENBB 1V/DIV CH2 OUTA, OUTB 1V/DIV 0.1 CH4 IOUT 200mV/DIV 0.01 CH4 IOUTA, IOUTB 200mV/DIV 0.001 0.0001 0.00001 4s/DIV 0 1 2 3 4 VREVERSE (V) 5 441312 G17 10s/DIV 441312 G18 6 441312 G16 441312fg 6 For more information www.linear.com/LTC4413-1 LTC4413-1/LTC4413-2 Typical Performance Characteristics ENBA, ENBB Turn-Off, 2s to Disconnect IN from 180mA Load Efficiency vs Load Current Power Loss vs Load Current 100 1000 98 CH4 IINA, IINB 100mV/DIV 100 97 96 95 94 93 120C 80C 40C 0C -40C 92 4s/DIV 441312 G19 POWER LOSS (mW) EFFICIENCY (%) CH2 OUTA, OUTB 1V/DIV CH3 ENBA, ENBB 1V/DIV 120C 80C 40C 0C -40C 99 CH1 INA, INB 1V/DIV 91 90 1 10 100 LOAD (mA) 1000 10 1 0 10000 10 1 100 LOAD (mA) 1000 441312 G20 400 140 6.2 350 120 5.8 OVP FALLING 5.6 5.4 300 200 150 0 40 0 40 80 OVI-OVP Voltage Drop vs OVI Voltage (LTC4413-2 Only) 140 140 IQ OVI = 13V 100 IQ OVI = 6.5V 80 60 2 1 8 6 OVI (V) 10 12 100 20 20 0 40 80 120 441312 G26 VOHOVP = 6.5V 60 40 0 -40 12 80 40 TEMPERATURE (C) 441312 G25 10 VOHOVP = 13V 120 OVI-OVP (mV) IQ OVI (A) 3 8 6 VOVI (V) 160 120 4 4 4 OVI-OVP vs Temperature (LTC4413-2 Only) 180 160 5 2 2 441312 G24 IQ OVI vs Temperature (LTC4413-2 Only) TA = 25C 0 0 441312 G23 441312 G22 0 0 120 TEMPERATURE (C) TEMPERATURE (C) 6 60 20 0 -40 120 80 80 40 100 50 5.0 -40 TA = 25C 100 250 IOVI (A) OVP RISING 6.0 OVP HYSTERESIS (mV) OVPIH/OVPIL (V) OVI Current vs Voltage (LTC4413-2 Only) 6.4 5.2 OVI-OVP (V) 441312 G21 Overvoltage Hysteresis vs Temperature (LTC4413-2 Only) Overvoltage Thresholds vs Temperature (LTC4413-2 Only) 10000 0 -40 -20 0 20 40 60 80 TEMPERATURE (C) 100 120 441312 G27 441312fg For more information www.linear.com/LTC4413-1 7 LTC4413-1/LTC4413-2 Pin Functions INA (Pin 1): Primary Ideal Diode Anode and Positive Power Supply for LTC4413-1/LTC4413-2. Bypass INA with a ceramic capacitor of at least 1F. (Series 1 snub resistors and higher valued capacitances are recommended when large inductances are in series with this input.) This pin can be grounded when not used. Limit slew rate on this pin to less than 2.5V/s. ENBA (Pin 2): Enable Low for Diode A. Pull this pin high to shut down this power path. Tie to GND to enable. Refer to Table 1 for mode control functionality. This pin can be left floating, a weak (3.5A) pull-down internal to LTC44131/ LTC4413-2 is included. OVP (Pin 7, LTC4413-2 Only): Drive Output for an External OVP Switch PMOS Transistor (To Inhibit Overvoltage Wall Adapter Voltages from Damaging Device.) During overvoltage conditions, this output will remain high so long as an overvoltage condition persists. This pin must be left floating when not in use. OVI (Pin 8, LTC4413-2 Only): Sense Input for Overvoltage Protection Block. This pin can be left floating or grounded when not used. GND (Pin 3): Power Ground for the IC. STAT (Pin 9): Status Condition Indicator. Weak (11A) pull-down current output. When terminated, high indicates diode conducting. Refer to Table 2 for the operation of this pin. This pin can also be left floating or grounded. ENBB (Pin 4): Enable Low for Diode B. Pull this pin high to shut down this power path. Tie to GND to enable. Refer to Table 1 for mode control functionality. This pin can be left floating, a weak (3.5A) pull-down internal to LTC44131/ LTC4413-2 is included. OUTA (Pin 10): Primary Ideal Diode Cathode and Output of the LTC4413-1/LTC4413-2. Bypass OUTA with a high (1m min) ESR ceramic capacitor of at least 4.7F. This pin must be left floating when not in use. Limit slew rate on this pin to less than 2.5V/s. INB (Pin 5): Secondary Ideal Diode Anode and Positive Power Supply for LTC4413-1/LTC4413-2. Bypass INB with a ceramic capacitor of at least 1F. (Series 1 snub resistors and higher valued capacitances are recommended when large inductances are in series with this input.) This pin can be grounded when not used. Limit slew rate on this pin to less than 2.5V/s. SGND (Exposed Pad Pin 11): Signal Ground. This pin must be soldered to PCB ground to provide both electrical contact to ground and good thermal contact to PCB. OUTB (Pin 6): Secondary Ideal Diode Cathode and Output of the LTC4413-1/LTC4413-2. Bypass OUTB with a high (1m min) ESR ceramic capacitor of at least 4.7F. This pin must be left floating when not in use. Limit slew rate on this pin to less than 2.5V/s. 441312fg 8 For more information www.linear.com/LTC4413-1 LTC4413-1/LTC4413-2 Block Diagram OUTA INA OVER CURRENT 2 ENBA 0.5V - + + - 1 -+ VOFF PA - + VGATEA AENA ENA UVLO ENA ENB OUTA (MAX) OUTB (MAX) A + - AENA OVER TEMP BENA OVER TEMP STAT STB 3A 5 GND OUTB INB OVER CURRENT 4 9 11A ENBB 0.5V - + + - 3 10 -+ VOFF ENB 6 PB - + VGATEB BENA B + - LTC4413-2 ONLY OVERVOLTAGE PROTECTION OVI 6V + - OVP 8 7 3A 441312 BD 441312fg For more information www.linear.com/LTC4413-1 9 LTC4413-1/LTC4413-2 Operation The LTC4413-1/LTC4413-2 are described with the aid of the Block Diagram. Operation begins when the power source at VINA or VINB rises above the undervoltage lockout (UVLO) voltage of 2.4V and the corresponding control pin ENBA or ENBB is low. If only the voltage at the VINA pin is present, the internal power source (VDD) is supplied from the VINA pin. The amplifier (A) pulls a current proportional to the difference between VINA and VOUTA from the gate (VGATEA) of the internal PFET (PA), driving this gate voltage below VINA. This turns on PA. As VOUTA pulls up to a forward voltage drop (VFWD) of 15mV below VINA, the LTC4413 regulates VGATEA to maintain the small forward voltage drop. The system is now in forward regulation and the load at VOUTA is powered from the supply at VINA. As the load current varies, VGATEA is controlled to maintain VFWD until the load current exceeds the transistor's (PA) ability to deliver the current as VGATEA approaches GND. At this point, the PFET behaves as a fixed resistor, RON, whereby the forward voltage increases slightly with increased load current. As the magnitude of IOUT increases further, (such that ILOAD > IOC) the LTC4413-1/LTC4413-2 fixes the load current to the constant value IOC to protect the device. The characteristics for parameters RFWD, RON, VFWD and IOC are specified with the aid of Figure 1, illustrating the LTC4413-1/LTC4413-2 forward voltage drop versus that of a Schottky. If another supply is provided at VINB, the LTC4413-1/ LTC4413-2 likewise regulate the gate voltage on PB to IOC maintain the output voltage, VOUTB, just below the input voltage VINB. If this alternate supply, VINB, exceeds the voltage at VINA, the LTC4413-1/LTC4413-2 selects this input voltage as the internal supply (VDD). This second ideal diode operates independently of the first ideal diode function. When an alternate power source is connected to the load at VOUTA (or VOUTB), the LTC4413-1/LTC4413-2 sense the increased voltage at VOUTA, and amplifier A increases the voltage VGATEA, reducing the current through PA. When VOUTA is higher than VINA + VRTO, VGATEA will be pulled up to VDD, turning off PA. The internal power source for the LTC4413-1/LTC4413-2 (VDD) then diverts to draw current from the VOUTA pin, only if VOUTA is larger than VINB (or VOUTB). The system is now in the reverse turn-off mode. Power to the load is being delivered from an alternate supply, and only a small current (ILEAK) is drawn from or sourced to VINA to sense the potential at VINA. When the selected channel of the LTC4413-1/LTC4413-2 is in reverse turn-off mode or both channels are disabled, the STAT pin sinks 11A of current (ISON) if connected. Channel selection is accomplished using the two pins, ENBA and ENBB. For example with channel A, when the ENBA input is asserted (high), PA has its gate voltage pulled to VDD, turning off PA. A 3.5A pull-down current on the ENBA, ENBB pins ensures a low level at these inputs if left floating. LTC4413-1 LTC4413-2 CURRENT (A) SLOPE: 1/RON IFWD 1N5817 SLOPE: 1/RFWD 0 0 VFWD FORWARD VOLTAGE (V) 441312 F01 Figure 1. The LTC4413 vs the 1N5817 441312fg 10 For more information www.linear.com/LTC4413-1 LTC4413-1/LTC4413-2 Operation Overcurrent and Short-Circuit Protection During an overcurrent condition, the output voltage droops as the load current exceeds the amount of current that the LTC4413-1/LTC4413-2 can supply. At the time when an overcurrent condition is first detected, the LTC44131/ LTC4413-2 take some time to detect this condition before reducing the current to IOC. For short durations after the output is shorted, until TOC, the current may exceed IOC. The magnitude of this peak short-circuit current can be large depending on the load current immediately before the short-circuit occurs. During overcurrent operation, the power consumption of the LTC4413-1/LTC4413-2 is large, and is likely to cause an overtemperature condition as the internal die temperature exceeds the thermal shutdown temperature. Overtemperature Protection The overtemperature condition is detected when the internal die temperature increases beyond 150C. An overtemperature condition will cause the gate amplifiers (A and B) as well as the two P-channel MOSFETs (PA and PB) to shut off. When the internal die temperature cools to below 140C, the amplifiers turn on and the LTC44131/LTC4413-2 reverts to normal operation. Note that prolonged operation under overtemperature conditions degrades reliability. Protection for more information on using the overvoltage protection function within the LTC4413-2. Channel Selection and Status Output Two active-high control pins independently turn off the two ideal diodes contained within the LTC4413-1/LTC4413-2, controlling the operation mode as described by Table 1. When the selected channel is reverse biased, or the LTC4413-1/LTC4413-2 is put into low power standby, the status signal indicates this condition with a low voltage. Table 1. Mode Control ENBA ENBB STATE Low Low Diode'OR NB: The Two Outputs are not Connected Internal to the Device Low High Diode A = ENABLED, Diode B = DISABLED High Low Diode A = DISABLED, Diode B = ENABLED High High All Off (Low Power Standby) The function of the STAT pin depends on the mode that has been selected. Table 2 describes the STAT pin output current, as a function of the mode selected as well as the conduction state of the two diodes. Table 2. STAT Output Pin Function ENBA ENBB CONDITIONS STAT Low Low Diode A Forward Bias, Diode B Forward Bias ISNK = 0A Diode A Forward Bias, Diode B Reverse Bias ISNK = 0A Diode A Reverse Bias, Diode B Forward Bias ISNK = 11A Diode A Reverse Bias, Diode B Reverse Bias ISNK = 11A Diode A Forward Bias, Diode B Disabled ISNK = 0A Diode A Reverse Bias, Diode B Disabled ISNK = 11A Diode A Disabled, Diode B Forward Bias ISNK = 0A Diode A Disabled, Diode B Reverse Bias ISNK = 11A Diode A Disabled, Diode B Disabled ISNK = 11A Overvoltage Protection (LTC4413-2 Only) An overvoltage condition is detected whenever the overvoltage input (OVI) pin is pulled above 6V. The condition persists until the OVI voltage falls below 5.6V. The overvoltage protection (OVP) output is low unless an overvoltage condition is detected. If an overvoltage condition is present, the OVP output is pulled up to the voltage applied to the OVI input. This output signal can be used to enable or disable an external PFET that is placed between the input that is the source of the excessive voltage and the input to the LTC4413-2, thus eliminating the potential damage that may occur to the LTC4413-2 if its input voltage exceeds the absolute maximum voltage of 6V. See the Applications Information section Dual Battery Load Sharing with Automatic Switchover to a Wall Adapter with Overvoltage Low High High High Low High 441312fg For more information www.linear.com/LTC4413-1 11 LTC4413-1/LTC4413-2 Applications Information Introduction The LTC4413-1/LTC4413-2 are intended for power control applications that include low loss diode OR'ing, fully automatic switchover from a primary to an auxiliary source of power, microcontroller controlled switchover from a primary to an auxiliary source of power, load sharing between two or more batteries, charging of multiple batteries from a single charger and high side power switching. Dual Battery Load Sharing with Automatic Switchover to a Wall Adapter with Overvoltage Protection (LTC4413-2 Only) An application circuit for dual battery load sharing with automatic switchover of load from batteries to a wall adapter is shown in Figure 2. When the wall adapter is not present, whichever battery has the higher voltage provides the load current until it has discharged to the voltage of the other battery. The load is shared between the two batteries according to the capacity of each battery. The higher capacity battery provides proportionally higher current to the load. When a wall adapter input is applied, the output voltage rises as the body diode in MP2 conducts. When the output voltage is larger than the battery voltages, the LTC4413 turns off and very little load current is drawn from the batteries. At this time, the STAT pin pulls down MP1 MP2 IRLML6402 IRLML6402 WALL ADAPTER INPUT JACK BATA + BATB + C1 0.10F R1 1 C2 10nF OUTA 10 1 INA TO LOAD 2 10nF RSTAT 470k 441312 F02 COUT 4.7F IDEAL Capacitor C2 is required to dynamically pull up on the gate of PFET MP1 if a fast edge occurs at the wall adapter input during a hot plug. In the event that capacitor C2 (or the gate-to-source of MP1) is precharged below the OVI rising threshold. When a high voltage spike occurs, the OVP output cannot guarantee turning off MP1 before the load voltage exceeds the absolute maximum voltage for the LTC4413-2. This may occur in the event that the wall adapter suddenly steps from 5.5V to a much higher value. In this case, a Zener diode is recommended to keep the output voltage to a safe level. Automatic PowerPath Control Figure 3 illustrates an application circuit for microcontroller monitoring and control of two power sources. The microcontroller's analog inputs (perhaps with the aid of a resistor voltage divider) monitor each supply input and the LTC4413-1 status, and then commands the LTC4413-1 through the two ENBA/ENBB control inputs. RSTAT 470k MICROCONTROLLER OPTIONAL 6.2V DFLZ6V2-7 IDEAL 9 STAT ENBA LTC4413-2 3 8 OVI GND 4 7 OVP ENBB OUTB 6 5 INB the gate voltage of MP2, causing it to conduct. This status signal can be used to provide information as to whether the wall adapter (or BATB) is supplying the load current. If the wall adapter voltage exceeds the OVI trip threshold (VOVIH) then the wall adapter is disconnected via the external PFET, MP1. The OVI voltage can be monitored (through a voltage divider if necessary) to determine if an overvoltage condition is present. PRIMARY POWER SOURCE RA 1 STAT OVP C1: C1206C106K8PAC C2: C0403C103K8PAC COUT: C1206C475K8PAC 2 3 4 AUXILIARY POWER SOURCE OUTA 10 1 INA CA 10F IDEAL ENBA STAT LTC4413-1 GND ENBB 5 INB CB 10F LOAD STAT OUTB 6 C1 4.7F IDEAL 441312 F03 RB 1 Figure 2 9 Figure 3 441312fg 12 For more information www.linear.com/LTC4413-1 LTC4413-1/LTC4413-2 Applications Information Automatic Switchover from a Battery to an Auxiliary Supply, or a Wall Adapter with Overvoltage Protection Figure 4 illustrates an application circuit where the LTC4413-2 is used to automatically switch over between a battery, an auxiliary power supply and a wall adapter. When the battery is supplying load current, OVP is at GND and STAT is high. If a higher supply is applied to AUX, the BAT will be disconnected from the load and the load is powered from AUX. When a wall adapter is applied, the body diode of MP2 forward biases. When the load voltage exceeds the AUX (or BAT) voltage, the LTC4413-2 senses this higher voltage and disconnects AUX (or BAT) from the load. At the same time it pulls the STAT voltage to GND, thereby turning on MP2. The load current is now supplied from the wall adapter. If the wall adapter voltage exceeds the OVI rising threshold, the OVP voltage rises and turns off MP1, disconnecting the wall adapter from the load. The output voltage collapses down to the AUX (or BAT) voltage and the LTC4413-2 reconnects the load to AUX (or BAT). MP1 MP2 IRLML6402 IRLML6402 WALL ADAPTER INPUT JACK + BAT C1 0.10F R1 1 OUTA 10 1 INA 3 4 GND IDEAL 470k 470k 2 OVI OPTIONAL 6.2V DFLZ6V2-7 TO LOAD 8 LTC4413-2 7 OVP ENBB 9 STAT OVP OUTB 6 10nF 5 INB AUX C2 10nF IDEAL COUT 4.7F ENBA 441312 F04 RSTAT 560k STAT Capacitor C2 is required to dynamically pull up on the gate of MP1 if a fast edge occurs at the wall adapter input during a hot plug. If the wall adapter voltage is precharged when an overvoltage spike occurs, the OVP voltage may not discharge capacitor C2 in time to protect the output. In this event, a Zener diode is recommended to protect the output node until MP1 is turned off. Multiple Battery Charging Figure 5 illustrates an application circuit for automatic dual battery charging from a single charger. Whichever battery has the lower voltage will receive the larger charging current until both battery voltages are equal, then both are charged. While both batteries are charging simultaneously, the higher capacity battery gets proportionally higher current from the charger. For Li-Ion batteries, both batteries achieve the float voltage minus the forward regulation voltage of 15mV. This concept can apply to more than two batteries. The STAT pin provides information as to when the battery at OUTA is being charged. For intelligent control, the ENBA/ENBB input pins can be used with a microcontroller as shown in Figure 3. BATTERY CHARGER INPUT OUTA 10 1 INA 2 IDEAL ENBA LTC4413-1 3 9 STAT GND 4 ENBB OUTB 6 5 INB IDEAL LOAD BAT1 470k STAT IS HIGH WHEN BAT1 IS CHARGING + C1: C1206C106K8PAC C2: C0403C103K8PAC COUT: C1206C475K8PAC Figure 4 + VCC LOAD BAT2 441312 F05 Figure 5 441312fg For more information www.linear.com/LTC4413-1 13 LTC4413-1/LTC4413-2 Applications Information Automatic Switchover from a Battery to a Wall Adapter and Charger with Overvoltage Protection Figure 6 illustrates the LTC4413-2 performing the function of automatically switching a load over from a battery to a wall adapter while controlling an LTC4059 battery charger. When no wall adapter is present, the LTC44132 connects the load at OUTA from the Li-Ion battery at INA. In this condition, the STAT voltage is high, thereby disabling the battery charger. If a wall adapter of a higher voltage than the battery is connected to MP1 (but below the OVI threshold), the load voltage rises as the second ideal diode conducts. As soon as the OUTA voltage exceeds the INA voltage, the BAT is disconnected from the load and the STAT voltage falls, turning on the LTC4059 battery charger and beginning a charge cycle. If a high voltage wall adapter is inadvertently attached above the OVI rising threshold, the OVP pin voltage rises, disconnecting both the LTC4413-2 and the LTC4059 from potentially hazardous voltages. When this occurs, the load voltage collapses until it is below the BAT voltage causing the STAT voltage to rise, disabling the battery charger. At the same time, the LTC4413-2 automatically reconnects the battery to the load. One major benefit of this circuit is that when a wall adapter is present, the user may remove the battery and replace it without disrupting the load. Capacitor C2 is required to dynamically pull up on the gate of MP1 if a fast edge occurs at the wall adapter input during a hot plug. If the wall adapter voltage is precharged when an overvoltage spike occurs, the OVP voltage may not discharge capacitor C2 in time to protect the output. In this event, a Zener diode is recommended to protect the output node until MP1 is turned off. STAT STAT ENB LTC4059 VCC PROG MP1 IRLML6402 WALL ADAPTER INPUT JACK 1F Li-Ion + 100k Li/CC GND C1 10F OUTA 10 1 INA BAT 9 RSTAT 560k IDEAL ENBA LTC4413-2 4 ENBB 3 GND OUTB 6 5 INB TO LOAD 2 D1 OPTIONAL DFLZ6V2-7 COUT 4.7F IDEAL OVP C2 10nF OVI 441312 F06 Figure 6 441312fg 14 For more information www.linear.com/LTC4413-1 LTC4413-1/LTC4413-2 Applications Information Soft-Start Overvoltage Protection an overvoltage event. When the overvoltage condition ends, the OVP voltage drops slowly, depending on the gate charge of the external PFET. This causes the external PFET to linger in a high RDS(ON) region where it can dissipate a significant amount of heat depending on the load current. To avoid dissipating heat in the external PFET, this application delays turning on the ideal diode from INA to OUTA, until the gate voltage of the external PFET drops below VENBIL, where the external PFET should safely be out of the high RDS(ON) region. This soft-start scheme can be used on either channel of the LTC4413-2. In the event that a low power external PFET is used for the external overvoltage protection device, care must be taken to limit the power dissipation in the external PFET. The operation of this circuit is identical to the "Automatic Switchover from a Battery to a Wall Adapter" application shown on the first page of this data sheet. Here, however, the ideal diode from INA to INB is disabled by pulling up on ENBA whenever an overvoltage condition is detected. This channel is turned-off using a resistor connected to OVP along with a 5.6V Zener diode, ensuring the absolute maximum voltage at ENBA is not exceeded during FDR8508 WALL ADAPTER INPUT INA C1 10F C2 10nF 0.1F D1 OPTIONAL OUTA IDEAL VCC RSTAT 470k RENBA 560k D2 5.6V 1 BAT + ENBA STAT LTC4413-2 OVI GND STAT OVP OUTB OVP ENBB INB COUT 4.7F IDEAL TO LOAD 441312 F07 C1: C0805C106K8PAC C2: C0403C103K8PAC COUT: C1206C475K8PAC STAT IS HIGH WHEN WALL ADAPTER IS SUPPLYING LOAD CURRENT OVP IS HIGH WHEN WALL ADAPTER VOLTAGE > 6V Figure 7 441312fg For more information www.linear.com/LTC4413-1 15 LTC4413-1/LTC4413-2 Package Description Please refer to http://www.linear.com/product/LTC4413-1#packaging for the most recent package drawings. DD Package 10-Lead Plastic DFN (3mm x 3mm) (Reference LTC DWG # 05-08-1699 Rev C) 0.70 0.05 3.55 0.05 1.65 0.05 2.15 0.05 (2 SIDES) PACKAGE OUTLINE 0.25 0.05 0.50 BSC 2.38 0.05 (2 SIDES) RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS 3.00 0.10 (4 SIDES) R = 0.125 TYP 6 0.40 0.10 10 1.65 0.10 (2 SIDES) PIN 1 NOTCH R = 0.20 OR 0.35 x 45 CHAMFER PIN 1 TOP MARK (SEE NOTE 6) 0.200 REF 0.75 0.05 0.00 - 0.05 5 1 (DD) DFN REV C 0310 0.25 0.05 0.50 BSC 2.38 0.10 (2 SIDES) BOTTOM VIEW--EXPOSED PAD NOTE: 1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (WEED-2). CHECK THE LTC WEBSITE DATA SHEET FOR CURRENT STATUS OF VARIATION ASSIGNMENT 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 441312fg 16 For more information www.linear.com/LTC4413-1 LTC4413-1/LTC4413-2 Revision History (Revision history begins at Rev E) REV DATE DESCRIPTION E 07/15 Changed GND to SGND in Pin Configuration PAGE NUMBER 2 Changed VENB to VENBA,B in electrical characteristics 3 Changed ENB to ENBA,B last two plots 4 Changed ENB to ENBA,B last plot 5 Changed ENB to ENBA,B first plot and changed IN to INA,B 6 Changed exposed pad/SGND label 7 Added sentence to final paragraph and added A,B references 9 Changed to ENBA and ENBB on Tables 1 and 2 10 Added LTC4415 to Related Parts table 16 F 09/16 Changed y-axis on graph G27 to OVI-OVP 7 G 09/17 Changed MP2 diode connection Figures 2, 4 12, 13 441312fg Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of itsinformation circuits as described herein will not infringe on existing patent rights. For more www.linear.com/LTC4413-1 17 LTC4413-1/LTC4413-2 Typical Application Automatic Switchover from a Battery to a Wall Adapter with Soft-Start Overvoltage Protection FDR8508 WALL ADAPTER INPUT INA C1 10F C2 10nF 0.1F D1 OPTIONAL OUTA IDEAL VCC RSTAT 470k RENBA 560k D2 5.6V 1 ENBA STAT LTC4413-2 OVI GND STAT OVP OUTB OVP ENBB INB BAT + COUT 4.7F IDEAL TO LOAD 441312 F07 C1: C0805C106K8PAC C2: C0403C103K8PAC COUT: C1206C475K8PAC STAT IS HIGH WHEN WALL ADAPTER IS SUPPLYING LOAD CURRENT OVP IS HIGH WHEN WALL ADAPTER VOLTAGE > 6V Related Parts PART NUMBER DESCRIPTION COMMENTS LTC1558/LTC1559 Backup Battery Controller with Programmable Output Adjustable Backup Voltage from 1.2V NiCd Button Cell, Includes Boost Converter LTC1998 2.5A, 1% Accurate Programmable Battery Detector Adjustable Trip Voltage/Hysteresis, ThinSOTTM LTC4054 800mA Standalone Linear Li-Ion Battery Charger with Thermal Regulation in ThinSOT No External MOSFET, Sense Resistor or Blocking Diode Required, Charge Current Monitor for Gas Gauging, C/10 Charge Termination LTC4350 Hot Swappable Load Share Controller Allows N + 1 Redundant Supply, Equally Loads Multiple Power Supplies Connected in Parallel LTC4411 2.6A Low Loss Ideal Diode in ThinSOT No External MOSFET, Automatic Switching Between DC Sources, Simplified Load Sharing LTC4412/ LTC4412HV PowerPath Controller in ThinSOT More Efficient than Diode OR'ing, Automatic Switching Between DC Sources, Simplified Load Sharing, 3V VIN 28V, 3V VIN 36V (HV) LTC4413 Dual 2.6A, 2.5V to 5.5V, Ideal Diodes in 3mm x 3mm DFN Lower Quiescent Current with Slower Response Time LTC4414 36V, Low Loss PowerPath Controller for Large PFETs Drives Large QG PFETs, Very Low Loss Replacement for Power Supply O'Ring Diodes, 3.5V to 36V AC/DC Adapter Voltage Range, 8-Lead MSOP Package LTC4415 Dual 4A Ideal Diodes with Adjustable Current Limit 1.7V to 5.5V Operating Range, 50m PMOS, Soft-Start, 15mV Forward Drop, MSOP-16 and 3mm x 5mm DFN-16 Packages 441312fg 18 LT 0917 REV G * PRINTED IN USA www.linear.com/LTC4413-1 For more information www.linear.com/LTC4413-1 LINEAR TECHNOLOGY CORPORATION 2006