LP2992 LP2992 Micropower 250 mA Low-Noise Ultra Low-Dropout Regulator in SOT-23 and LLP Packages Designed for Use with Very Low ESR Output Capacitors Designed for Use with Very Low ESR Output Capacitors Literature Number: SNVS171F LP2992 Micropower 250 mA Low-Noise Ultra Low-Dropout Regulator in SOT-23 and LLP Packages Designed for Use with Very Low ESR Output Capacitors Designed for Use with Very Low ESR Output Capacitors General Description Features The LP2992 is a 250 mA, fixed-output voltage regulator designed to provide ultra low-dropout and low noise in battery powered applications. Using an optimized VIP(R) (Vertically Integrated PNP) process, the LP2992 delivers unequalled performance in all specifications critical to battery-powered designs: Dropout Voltage: Typically 450 mV @ 250 mA load, and 5 mV @ 1 mA load. Ground Pin Current: Typically 1500 A @ 250 mA load, and 75 A @ 1 mA load. Enhanced Stability: The LP2992 is stable with output capacitor ESR as low as 5 m, which allows the use of ceramic capacitors on the output. Sleep Mode: Less than 1 A quiescent current when ON/OFF pin is pulled low. Smallest Possible Size: SOT-23 and LLP packages use absolute minimum board space. Precision Output: 1% tolerance output voltages available (A grade). Low Noise: By adding a 10 nF bypass capacitor, output noise can be reduced to 30 V (typical). Multiple voltage options, from 1.5V to 5.0V, are available as standard products. Consult factory for custom voltages. Ultra low dropout voltage Guaranteed 250 mA output current Smallest possible size (SOT-23, LLP package) Requires minimum external components Stable with low-ESR output capacitor <1 A quiescent current when shut down Low ground pin current at all loads Output voltage accuracy 1% (A Grade) High peak current capability Wide supply voltage range (16V max) Low ZOUT: 0.3 typical (10 Hz to 1 MHz) Overtemperature/overcurrent protection -40C to +125C junction temperature range Custom voltages available Applications Cellular Phone Palmtop/Laptop Computer Personal Digital Assistant (PDA) Camcorder, Personal Stereo, Camera Block Diagram 20029401 VIP(R) is a registered trademark of National Semiconductor Corporation. (c) 2010 National Semiconductor Corporation 200294 www.national.com LP2992 Micropower 250 mA Low-Noise Ultra Low-Dropout Regulator in SOT-23 and LLP Packages Designed for Use with Very Low ESR Output Capacitors Designed for Use with Very Low ESR Output Capacitors July 22, 2010 LP2992 Basic Application Circuit 20029402 *ON/OFF input must be actively terminated. Tie to VIN if this function is not to be used. **Minimum capacitance is shown to ensure stability (may be increased without limit). Ceramic capacitor required for output (see Application Hints). ***Reduces output noise (may be omitted if application is not noise critical). Use ceramic or film type with very low leakage current (see Application Hints). Connection Diagrams 5-Lead Small Outline Package (M5) 6-Lead LLP Package (LD) 20029403 Top View See NS Package Number MF05A For ordering information see Table 1 www.national.com 20029446 Top View See NS Package Number NLDBA006 Outline Drawing LDE06A 2 LP2992 Ordering Information TABLE 1. Package Marking and Ordering Information Output Voltage (V) Grade Order Information Package Marking Supplied as: 5-Lead Small Outline Package (M5) 1.5 A LP2992AIM5X-1.5 LFBA 3000 Units on Tape and Reel 1.5 A LP2992AIM5-1.5 LFBA 1000 Units on Tape and Reel 1.5 STD LP2992IM5X-1.5 LFBB 3000 Units on Tape and Reel 1.5 STD LP2992IM5-1.5 LFBB 1000 Units on Tape and Reel 1.8 A LP2992AIM5X-1.8 LFCA 3000 Units on Tape and Reel 1.8 A LP2992AIM5-1.8 LFCA 1000 Units on Tape and Reel 1.8 STD LP2992IM5X-1.8 LFCB 3000 Units on Tape and Reel 1.8 STD LP2992IM5-1.8 LFCB 1000 Units on Tape and Reel 2.5 A LP2992AIM5X-2.5 LFDA 3000 Units on Tape and Reel 2.5 A LP2992AIM5-2.5 LFDA 1000 Units on Tape and Reel 2.5 STD LP2992IM5X-2.5 LFDB 3000 Units on Tape and Reel 2.5 STD LP2992IM5-2.5 LFDB 1000 Units on Tape and Reel 3.0 A LP2992AIM5X-3.0 LF8A 3000 Units on Tape and Reel 3.0 A LP2992AIM5-3.0 LF8A 1000 Units on Tape and Reel 3.0 STD LP2992IM5X-3.0 LF8B 3000 Units on Tape and Reel 3.0 STD LP2992IM5-3.0 LF8B 1000 Units on Tape and Reel 3.3 A LP2992AIM5X-3.3 LFEA 3000 Units on Tape and Reel 3.3 A LP2992AIM5-3.3 LFEA 1000 Units on Tape and Reel 3.3 STD LP2992IM5X-3.3 LFEB 3000 Units on Tape and Reel 3.3 STD LP2992IM5-3.3 LFEB 1000 Units on Tape and Reel 5.0 A LP2992AIM5X-5.0 LFFA 3000 Units on Tape and Reel 5.0 A LP2992AIM5-5.0 LFFA 1000 Units on Tape and Reel 5.0 STD LP2992IM5X-5.0 LFFB 3000 Units on Tape and Reel 5.0 STD LP2992IM5-5.0 LFFB 1000 Units on Tape and Reel 6-Lead LLP Package (LDE06A) 1.5 A LP2992AILDX-1.5 L011A 4500 Units on Tape and Reel 1.5 A LP2992AILD-1.5 L011A 1000 Units on Tape and Reel 1.5 STD LP2992ILDX-1.5 L011AB 4500 Units on Tape and Reel 1.5 STD LP2992ILD-1.5 L011AB 1000 Units on Tape and Reel 1.8 A LP2992AILDX-1.8 L012A 4500 Units on Tape and Reel 1.8 A LP2992AILD-1.8 L012A 1000 Units on Tape and Reel 1.8 STD LP2992ILDX-1.8 L012AB 4500 Units on Tape and Reel 1.8 STD LP2992ILD-1.8 L012AB 1000 Units on Tape and Reel 2.5 A LP2992AILDX-2.5 L013A 4500 Units on Tape and Reel 2.5 A LP2992AILD-2.5 L013A 1000 Units on Tape and Reel 2.5 STD LP2992ILDX-2.5 L013AB 4500 Units on Tape and Reel 2.5 STD LP2992ILD-2.5 L013AB 1000 Units on Tape and Reel 3.3 A LP2992AILDX-3.3 L014A 4500 Units on Tape and Reel 3.3 A LP2992AILD-3.3 L014A 1000 Units on Tape and Reel 3.3 STD LP2992ILDX-3.3 L014AB 4500 Units on Tape and Reel 3.3 STD LP2992ILD-3.3 L014AB 1000 Units on Tape and Reel 5.0 A LP2992AILDX-5.0 L015A 4500 Units on Tape and Reel 5.0 A LP2992AILD-5.0 L015A 1000 Units on Tape and Reel 5.0 STD LP2992ILDX-5.0 L015AB 4500 Units on Tape and Reel 5.0 STD LP2992ILD-5.0 L015AB 1000 Units on Tape and Reel 3 www.national.com LP2992 Power Dissipation (Note 3) Input Supply Voltage (Survival) Input Supply Voltage (Operating) Shutdown Input Voltage (Survival) Output Voltage (Survival, (Note 4)) IOUT (Survival) Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Storage Temperature Range Operating Junction Temperature Range Lead Temp. (Soldering, 5 sec.) ESD Rating (Note 2) -65C to +150C -40C to +125C 260C 2 kV Internally Limited -0.3V to +16V 2.2V to +16V -0.3V to +16V -0.3V to +9V Short Circuit Protected -0.3V to +16V Input-Output Voltage (Survival, (Note 5)) Electrical Characteristics Limits in standard typeface are for TJ = 25C. and limits in boldface type apply over the full operating temperature range. Unless otherwise specified: VIN = VO(NOM) + 1V, IL = 1 mA, CIN = 1 F, COUT = 4.7 F, VON/OFF = 2V. Symbol VO LP2992AI-X.X (Note 6) LP2992I-X.X (Note 6) Min Max Min Max IL = 1 mA -1.0 1.0 -1.5 1.5 1 mA IL 50 mA -1.5 1.5 -2.5 2.5 -2.5 2.5 -3.5 3.5 -3.5 3.5 -4.0 4.0 4.5 -5.0 Parameter Output Voltage Tolerance Conditions Typ 1 mA IL 250 mA -4.5 Output Voltage VO(NOM)+1V VIN 16V 0.007 Units %VNOM 5.0 0.014 0.014 0.032 0.032 2.05 2.20 2.20 0.5 2.5 2.5 4 4 %/V Line Regulation VIN(min) Minimum input voltage required to maintain outpout regulation VIN-VO Dropout Voltage (Note 7) IL = 0 IL = 1 mA 5 IL = 50 mA IGND Ground Pin Current 100 IL = 150 mA 260 IL = 250 mA 450 IL = 0 65 IL = 1 mA 75 IL = 50 mA VON/OFF www.national.com ON/OFF Input Voltage (Note 8) 350 IL = 150 mA 850 IL = 250 mA 1500 9 9 12 12 125 125 180 180 325 325 470 470 575 575 850 850 95 95 125 125 110 110 170 170 600 600 1000 1000 1500 1500 2500 2500 2300 2300 4000 4000 VON/OFF < 0.3V 0.01 0.8 0.8 VON/OFF < 0.15V 0.05 2 2 High = O/P ON 1.4 Low = O/P OFF 0.55 4 1.6 1.6 0.15 0.15 V mV A V ION/OFF en Parameter ON/OFF Input Current Output Noise Voltage (RMS) Conditions Typ VON/OFF = 0 LP2992I-X.X (Note 6) Min Min Max Units Max 0.01 -2 -2 VON/OFF = 5V 5 15 15 BW = 300 Hz to 50 kHz, COUT = 10 F 30 V 45 dB 400 mA 350 mA A CBYPASS = 10 nF Ripple Rejection f = 1 kHz, CBYPASS = 10 nF COUT = 10 F IO(SC) Short Circuit Current RL = 0 (Steady State) (Note 9) IO(PK) Peak Output Current VOUT Vo(NOM) -5% Note 1: "Absolute Maximum Ratings" indicate limits beyond which damage to the component may occur. Electrical specifications do not apply when operating the device outside of its rated operating conditions. Note 2: The ESD rating of pins 3 and 4 for the SOT-23 package, or pins 1 and 3 for the LLP package, is 1 kV. Note 3: The maximum allowable power dissipation is a function of the maximum junction temperature, TJ(MAX), the junction-to-ambient thermal resistance, JA, and the ambient temperature, TA. The maximum allowable power dissipation at any ambient temperture is calculated using: Where the value of J-A for the SOT-23 package is 220C/W in a typical PC board mounting and the LLP package is 65C/W. Exceeding the maximum allowable dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. Note 4: If used in a dual-supply system where the regulator load is returned to a negative supply, the LP2992 output must be diode-clamped to ground. Note 5: The output PNP structure contains a diode between the VIN to VOUT terminals that is normally reverse-biased. Reversing the polarity from VIN to VOUT will turn on this diode. Note 6: Limits are 100% production tested at 25C. Limits over the operating temperature range are guaranteed through correlation using Statistical Quality Control (SQC) methods. The limits are used to calculate National's Average Outgoing Quality Level (AOQL). Note 7: VIN must be the greater of 2.2V or VOUT(nom) + Dropout Voltage to maintain output regulation. Dropout voltage is defined as the input to output differential at which the output voltage drops 2% below the value measured with a 1V differential. Note 8: The ON/OFF input must be properly driven to prevent possible misoperation. For details, refer to Application Hints. Note 9: The LP2992 has foldback current limiting which allows a high peak current when VOUT > 0.5V, and then reduces the maximum output current as VOUT is forced to ground (see Typical Performance Characteristics curves). 5 www.national.com LP2992 Symbol LP2992AI-X.X (Note 6) LP2992 Typical Performance Characteristics Unless otherwise specified: CIN = 1F, COUT = 4.7F, VIN = VOUT (NOM) +1, TA = 25C, ON/OFF pin is tied to VIN. VOUT vs Temperature Short-Circuit Current 20029409 20029408 Short-Circuit Current Short Circuit Current vs Output Voltage 20029410 20029411 Ripple Rejection Ripple Rejection 20029413 www.national.com 20029414 6 LP2992 Ripple Rejection Ripple Rejection 20029415 20029416 Ripple Rejection Ripple Rejection 20029417 20029418 Ripple Rejection Ripple Rejection 20029419 20029423 7 www.national.com LP2992 Ripple Rejection Output Impedance vs Frequency 20029420 20029422 Output Impedance vs Frequency Output Noise Density 20029424 20029421 Output Noise Density GND Pin vs Load Current 20029425 www.national.com 20029426 8 LP2992 Dropout Voltage vs Temperature Input Current vs Pin 20029427 20029429 Ignd vs Load and Temperature Instantaneous Short Circuit Current 20029430 20029431 Load Transient Response Load Transient Response 20029433 20029434 9 www.national.com LP2992 Load Transient Response Line Transient Response 20029435 20029447 Line Transient Response Line Transient Response 20029436 20029437 Line Transient Response Turn-On Time 20029438 www.national.com 20029439 10 LP2992 Turn-On Time Turn-On Time 20029441 20029440 Turn-On Time 20029442 11 www.national.com LP2992 Application Hints amount of output capacitance is provided over the full operating temperature range. It should be noted that ceramic capacitors can exhibit large changes in capacitance with temperature (see next section, Capacitor Characteristics). The output capacitor must be located not more than 1 cm from the output pin and returned to a clean analog ground. Noise Bypass Capacitor: Connecting a 10 nF capacitor to the Bypass pin significantly reduces noise on the regulator output. It should be noted that the capacitor is connected directly to a high-impedance circuit in the bandgap reference. Because this circuit has only a few microamperes flowing in it, any significant loading on this node will cause a change in the regulated output voltage. For this reason, DC leakage current through the noise bypass capacitor must never exceed 100 nA, and should be kept as low as possible for best output voltage accuracy. The types of capacitors best suited for the noise bypass capacitor are ceramic and film. High-quality ceramic capacitors with either NPO or COG dielectric typically have very low leakage. 10 nF polypropolene and polycarbonate film capacitors are available in small surface-mount packages and typically have extremely low leakage current. EXTERNAL CAPACITORS Like any low-dropout regulator, the LP2992 requires external capacitors for regulator stability. These capacitors must be correctly selected for good performance. Input Capacitor An input capacitor whose capacitance is 1 F is required between the LP2992 input and ground (the amount of capacitance may be increased without limit). This capacitor must be located a distance of not more than 1 cm from the input pin and returned to a clean analog ground. Any good quality ceramic, tantalum, or film capacitor may be used at the input. Important: Tantalum capacitors can suffer catastrophic failure due to surge current when connected to a low-impedance source of power (like a battery or very large capacitor). If a Tantalum capacitor is used at the input, it must be guaranteed by the manufacturer to have a surge current rating sufficient for the application. There are no requirements for ESR on the input capacitor, but tolerance and temperature coefficient must be considered when selecting the capacitor to ensure the capacitance will be 1 F over the entire operating temperature range. Output Capacitor: The LP2992 is designed specifically to work with ceramic output capacitors, utilizing circuitry which allows the regulator to be stable across the entire range of output current with an output capacitor whose ESR is as low as 5 m. It may also be possible to use Tantalum or film capacitors at the output, but these are not as attractive for reasons of size and cost (see next section Capacitor Characteristics). The output capacitor must meet the requirement for minimum amount of capacitance and also have an ESR (equivalent series resistance) value which is within the stable range. Curves are provided which show the stable ESR range as a function of load current (see ESR graph below). CAPACITOR CHARACTERISTICS The LP2992 was designed to work with ceramic capacitors on the output to take advantage of the benefits they offer: for capacitance values in the 2.2 F to 10 F range, ceramics are the least expensive and also have the lowest ESR values (which makes them best for eliminating high-frequency noise). The ESR of a typical 4.7 F ceramic capacitor is in the range of 5 m to 10 m, which easily meets the ESR limits required for stability by the LP2992. One disadvantage of ceramic capacitors is that their capacitance can vary with temperature. Most large value ceramic capacitors ( 2.2 F) are manufactured with the Z5U or Y5V temperature characteristic, which results in the capacitance dropping by more than 50% as the temperature goes from 25 C to 85C. This could cause problems if a 4.7 F capacitor were used on the output since it will drop down to approximately 2.3 F at high ambient temperatures (which could cause the LP2992 to oscillate). If Z5U or Y5V capacitors are used on the output, a minimum capacitance value of 10 F must be observed. A better choice for temperature coefficient in ceramic capacitors is X7R, which holds the capacitance within 15%. Unfortunately, the larger values of capacitance are not offered by all manufacturers in the X7R dielectric. Tantalum: Tantalum capacitors are less desirable than ceramics for use as output capacitors because they are more expensive when comparing equivalent capacitance and voltage ratings in the 1 F to 4.7 F range. Another important consideration is that Tantalum capacitors have higher ESR values than equivalent size ceramics. This means that while it may be possible to find a Tantalum capacitor with an ESR value within the stable range, it would have to be larger in capacitance (which means bigger and more costly) than a ceramic capacitor with the same ESR value. It should also be noted that the ESR of a typical Tantalum will increase about 2:1 as the temperature goes from 25C down to -40C, so some guard band must be allowed. 20029407 Important: The output capacitor must maintain its ESR within the stable region over the full operating temperature range of the application to assure stability. The LP2992 requires a minimum of 4.7 F on the output (output capacitor size can be increased without limit). It is important to remember that capacitor tolerance and variation with temperature must be taken into consideration when selecting an output capacitor so that the minimum required www.national.com 12 LLP MOUNTING The LLP package requires specific mounting techniques which are detailed in National Semiconductor Application Note # 1187. Referring to the section PCB Design Recommendations, it should be noted that the pad style which should be used with the LLP package is the NSMD (non-solder mask defined) type. The thermal dissipation of the LLP package is directly related to the printed circuit board construction and the amount of additional copper area. For the LP2992 in the LDE06A 6-Lead LLP package, the junction-to-case thermal rating, JC, is 19C/W, where the case is actually the bottom of the package at the center of the DAP. The junction-to-ambient thermal performance for the LP2992 in the LDE06A 6-Lead LLP package, using the JEDEC standards is summarized in the following table: REVERSE INPUT-OUTPUT VOLTAGE The PNP power transistor used as the pass element in the LP2992 has an inherent diode connected between the regulator output and input. During normal operation (where the input voltage is higher than the output) this diode is reversebiased. However, if the output is pulled above the input, this diode will turn ON and current will flow into the regulator output. In such cases, a parasitic SCR can latch which will allow a high current to flow into VIN (and out the ground pin), which can damage the part. In any application where the output may be pulled above the input, an external Schottky diode must be connected from Board Type Thermal Vias JC JA JEDEC 2-Layer None 19C/W 282C/W 1 19C/W 94C/W 2 19C/W 78C/W 4 19C/W 66C/W 6 19C/W 62C/W JEDEC 4-Layer 13 www.national.com LP2992 VIN to VOUT (cathode on VIN, anode on VOUT), to limit the reverse voltage across the LP2992 to 0.3V (see Absolute Maximum Ratings). ON/OFF INPUT OPERATION The LP2992 is shut off by driving the ON/OFF input low, and turned on by pulling it high. If this feature is not to be used, the ON/OFF input should be tied to VIN to keep the regulator output on at all times. To assure proper operation, the signal source used to drive the ON/OFF input must be able to swing above and below the specified turn-on/turn-off voltage thresholds listed in the Electrical Characteristics section under VON/OFF. To prevent misoperation, the turn-on (and turn-off) voltage signals applied to the ON/OFF input must have a slew rate which is 40 mV/s. Caution: the regulator output voltage can not be guaranteed if a slow-moving AC (or DC) signal is applied that is in the range between the specified turn-on and turn-off voltages listed under the electrical specification VON/OFF (see Electrical Characteristics). LP2992 Physical Dimensions inches (millimeters) unless otherwise noted 5-Lead Small Outline Package (M5) NS Package Number MF05A For Order Numbers, refer to Table 1 in the "Ordering Information" section of this document. 6-Lead LLP Package (LD) NS Package Number LDE06A www.national.com 14 LP2992 15 www.national.com LP2992 Micropower 250 mA Low-Noise Ultra Low-Dropout Regulator in SOT-23 and LLP Packages Designed for Use with Very Low ESR Output Capacitors Designed for Use with Very Low ESR Output Capacitors Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: www.national.com Products Design Support Amplifiers www.national.com/amplifiers WEBENCH(R) Tools www.national.com/webench Audio www.national.com/audio App Notes www.national.com/appnotes Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns Data Converters www.national.com/adc Samples www.national.com/samples Interface www.national.com/interface Eval Boards www.national.com/evalboards LVDS www.national.com/lvds Packaging www.national.com/packaging Power Management www.national.com/power Green Compliance www.national.com/quality/green Switching Regulators www.national.com/switchers Distributors www.national.com/contacts LDOs www.national.com/ldo Quality and Reliability www.national.com/quality LED Lighting www.national.com/led Feedback/Support www.national.com/feedback Voltage References www.national.com/vref Design Made Easy www.national.com/easy www.national.com/powerwise Applications & Markets www.national.com/solutions Mil/Aero www.national.com/milaero PowerWise(R) Solutions Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors SolarMagicTM www.national.com/solarmagic PLL/VCO www.national.com/wireless www.national.com/training PowerWise(R) Design University THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2010 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated