Through Hole Lamp Product Data Sheet LTL-307G-011A Spec No.: DS20-2015-0180 Effective Date: 07/18/2015 Revision: - LITE-ON DCC RELEASE BNS-OD-FC001/A4 LITE-ON Technology Corp. / Optoelectronics No.90,Chien 1 Road, Chung Ho, New Taipei City 23585, Taiwan, R.O.C. Tel: 886-2-2222-6181 Fax: 886-2-2221-1948 / 886-2-2221-0660 http://www.liteon.com/opto Through Hole Lamp LTL-307G-011A Through Hole Lamp LTL-307G-011A Rev P001 Description Preliminary SPEC (RDR-20140161-01) By Date Sasipan 03/18/2014 Above data for PD and Customer tracking only - NPPR Received and Upload on OPNC Sasipan 1/10 06/29/2015 Part No. : LTL-307G-011A BNS-OD-FC002/A4 Through Hole Lamp LTL-307G-011A 1. Description Through-hole LEDs are offered in a variety of packages such as 3mm, 4mm, 5mm, rectangular, and cylinder which are suitable for all applications requiring status indication. Several intensity and viewing angle choices are available in each color for design flexibility. 1. 1. Features Low power consumption & High efficiency Lead free & RoHS Compliant Popular T-13/4 diameter Yellow Green 569nm Lamp & Green Diffused lens 1.2. Applications Communication Computer Consumer Home appliance Industrial 2. Outline Dimensions Notes : 1. 2. 3. 4. All dimensions are in millimeters (inches). Tolerance is 0.25mm (.010") unless otherwise noted. Protruded resin under flange is 1.0mm (.04") max. Lead spacing is measured where the leads emerge from the package. 5. Specifications are subject to change without notice. 2/10 Part No. : LTL-307G-011A BNS-OD-FC002/A4 Through Hole Lamp LTL-307G-011A 3. Absolute Maximum Ratings at TA=25C Parameter Maximum Rating Unit 52 mW (Duty Cycle1/10, Pulse Width10ms) 60 mA DC Forward Current 20 mA Power Dissipation Peak Forward Current Operating Temperature Range -40C to + 85C Storage Temperature Range -40C to + 100C Lead Soldering Temperature [2.0mm (.079") From Body] 260C for 5 Seconds Max. 4. Electrical / Optical Characteristics at TA=25C Parameter Symbol Min. Typ. Max. Unit IV 8.7 30 100 mcd Test Condition IF = 10mA Luminous Intensity 21/2 50 deg Peak Emission Wavelength P 565 nm Dominant Wavelength d Viewing Angle Note 1,5 Note 2 (Fig.6) Measurement @Peak (Fig.1) IF = 10mA 566 569 573 nm Note 4 Spectral Line Half-Width Forward Voltage VF Reverse Current IR 30 1.6 2.1 nm 2.6 V IF = 20mA 100 A VR = 5V NOTE: 1. Luminous intensity is measured with a light sensor and filter combination that approximates the CIE eye-response curve. 2. 1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity. 3. Iv classification code is marked on each packing bag. 4. The dominant wavelength, d is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. 5. Iv guarantee must be included with 15% testing tolerance. 6. Reverse voltage (VR) condition is applied for IR test only. The device is not designed for reverse operation. 3/10 Part No. : LTL-307G-011A BNS-OD-FC002/A4 Through Hole Lamp LTL-307G-011A 5. Typical Electrical / Optical Characteristics Curves (25C Ambient Temperature Unless Otherwise Noted) 4/10 Part No. : LTL-307G-011A BNS-OD-FC002/A4 Through Hole Lamp LTL-307G-011A 6. Taping Features * Compatible with radial lead automatic insertion equipment. * Most radial lead plastic lead lamps available packaged in tape and folding. * 2.54mm (0.1") straight lead spacing available. * Folding packaging simplifies handling and testing. * Reel packaging is available by removing suffix "A" on option. Package Dimensions Specification Item Symbol Minimum Maximum mm inch mm inch D 3.8 0.149 4.2 0.165 Component Lead Pitch F 4.8 0.188 5.8 0.228 Front to Rear Deflection H -- -- 2.0 0.078 Height of Seating Plane H 15.5 0.610 16.5 0.649 Feed Hole to Bottom of Component H1 19.0 0.748 21.0 0.827 Feed Hole to Overall Component Height H2 27.3 1.074 29.9 1.177 11.0 0.433 Tape Feed Hole Diameter Lead Length After Component Height L Feed Hole Pitch P 12.4 0.488 13.0 0.511 Lead Location P1 3.15 0.124 4.55 0.179 Center of P2 5.05 0.198 7.65 0.301 Component Location Total Tape Thickness W0 T -- -- 0.90 0.035 Feed Hole Location W0 8.5 0.334 9.75 0.384 Adhesive Tape Position W2 0 0 3.0 0.118 Tape Width W3 17.5 0.689 19.0 0.748 5/10 Part No. : LTL-307G-011A BNS-OD-FC002/A4 Through Hole Lamp LTL-307G-011A 7. Packing Spec. Total 2,000pcs per inner carton 10 Inner cartons per outer carton Total 20,000 pcs per outer carton In every shipping lot, only the last pack will be non-full packing 6/10 Part No. : LTL-307G-011A BNS-OD-FC002/A4 Through Hole Lamp LTL-307G-011A 8. Bin Table Specification Luminous Intensity Unit : mcd @10mA Bin Code Min. Max. M4 8.7 12.6 M3 12.6 19 M2 19 29 M1 29 40 N1 40 100 Note: Tolerance of each bin limit is 15% Dominant Wavelength Unit : nm @10mA Bin Code Min Max GG1 566 568 GG 568 569.5 PG 569.5 571 YG 571 573 Note: Tolerance of each bin limit is 1nm 7/10 Part No. : LTL-307G-011A BNS-OD-FC002/A4 Through Hole Lamp LTL-307G-011A 9. CAUTIONS 9.1. Application This LED lamp is good for application of indoor and outdoor sign, also ordinary electronic equipment. 9.2. Storage The storage ambient for the LEDs should not exceed 30C temperature or 70% relative humidity. It is recommended that LEDs out of their original packaging are used within three months. For extended storage out of their original packaging, it is recommended that the LEDs be stored in a sealed container with appropriate desiccant or in desiccators with nitrogen ambient. 9.3. Cleaning Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LEDs if necessary. 9.4. Lead Forming & Assembly During lead forming, the leads should be bent at a point at least 3mm from the base of LED lens. Do not use the base of the lead frame as a fulcrum during forming. Lead forming must be done before soldering, at normal temperature. During assembly on PCB, use minimum clinch force possible to avoid excessive mechanical stress. 9.5. Soldering When soldering, leave a minimum of 2mm clearance from the base of the lens to the soldering point. Dipping the lens into the solder must be avoided. Do not apply any external stress to the lead frame during soldering while the LED is at high temperature. Recommended soldering conditions: Soldering iron Temperature Soldering time Position 350C Max. 3 seconds Max. (one time only) No closer than 2mm from the base of the epoxy bulb Wave soldering Pre-heat Pre-heat time Solder wave Soldering time Dipping Position 100C Max. 60 seconds Max. 260C Max. 5 seconds Max. No lower than 2mm from the base of the epoxy bulb Note: Excessive soldering temperature and/or time might result in deformation of the LED lens or catastrophic failure of the LED. IR reflow is not suitable process for through hole type LED lamp product. 9.6. Drive Method An LED is a current-operated device. In order to ensure intensity uniformity on multiple LEDs connected in parallel in an application, it is recommended that a current limiting resistor be incorporated in the drive circuit, in series with each LED as shown in Circuit A below. Circuit model (A) LED Circuit model (B) LED (A) Recommended circuit (B) The brightness of each LED might appear different due to the differences in the I-V characteristics of those LEDs. 8/10 Part No. : LTL-307G-011A BNS-OD-FC002/A4 Through Hole Lamp LTL-307G-011A 9.7. ESD (Electrostatic Discharge) Static Electricity or power surge will damage the LED. Suggestions to prevent ESD damage: Use a conductive wrist band or anti- electrostatic glove when handling these LEDs All devices, equipment, and machinery must be properly grounded Work tables, storage racks, etc. should be properly grounded Use ion blower to neutralize the static charge which might have built up on surface of the LEDs plastic lens as a result of friction between LEDs during storage and handing Suggested checking list: Training and Certification 9.7.1.1. Everyone working in a static-safe area is ESD-certified? 9.7.1.2. Training records kept and re-certification dates monitored? Static-Safe Workstation & Work Areas 9.7.2.1. Static-safe workstation or work-areas have ESD signs? 9.7.2.2. All surfaces and objects at all static-safe workstation and within 1 ft measure less than 100V? 9.7.2.3. All ionizer activated, positioned towards the units? 9.7.2.4. Each work surface mats grounding is good? Personnel Grounding 9.7.3.1. Every person (including visitors) handling ESD sensitive (ESDS) items wear wrist strap, heel strap or conductive shoes with conductive flooring? 9.7.3.1. If conductive footwear used, conductive flooring also present where operator stand or walk? 9.7.3.2. Garments, hairs or anything closer than 1 ft to ESD items measure less than 100V*? 9.7.3.3. Every wrist strap or heel strap/conductive shoes checked daily and result recorded for all DLs? 9.7.3.4. All wrist strap or heel strap checkers calibration up to date? Note: *50V for Blue LED. Device Handling 9.7.4.1. Every ESDS items identified by EIA-471 labels on item or packaging? 9.7.4.2. All ESDS items completely inside properly closed static-shielding containers when not at static-safe workstation? 9.7.4.3. No static charge generators (e.g. plastics) inside shielding containers with ESDS items? 9.7.4.4. All flexible conductive and dissipative package materials inspected before reuse or recycle? Others 9.7.5.1. Audit result reported to entity ESD control coordinator? 9.7.5.2. Corrective action from previous audits completed? 9.7.5.3. Are audit records complete and on file? 9/10 Part No. : LTL-307G-011A BNS-OD-FC002/A4 Through Hole Lamp LTL-307G-011A 10. Reliability Test Classification Endurance Test Item Test Condition Sample Size Reference Standard Operation Life Ta = Under room temperature IF = per datasheet maximum drive current Test Time= 1000hrs 22 PCS (CL=90%; LTPD=10%) High Temperature High Humidity storage Ta = 60C RH = 90% Test Time= 240hrs 22 PCS (CL=90%; LTPD=10%) High Temperature Storage Ta= 105 5C Test Time= 1000hrs 22 PCS (CL=90%; LTPD=10%) MIL-STD-750D:1031 (1995) MIL-STD-883G:1008 (2006) JEITA ED-4701:200 201 (2001) Low Temperature Storage Ta= -55 5C Test Time= 1000hrs 22 PCS (CL=90%; LTPD=10%) JEITA ED-4701:200 202 (2001) Temperature Cycling 100C 25C -40C 25C 30mins 5mins 30mins 5mins 30 Cycles 22 PCS (CL=90%; LTPD=10%) MIL-STD-750D:1051 (1995) MIL-STD-883G:1010 (2006) JEITA ED-4701:100 105 (2001) JESD22-A104C (2005) Thermal Shock 100 5C -30C 5C 15mins 15mins 30 Cycles (<20 secs transfer) 22 PCS (CL=90%; LTPD=10%) MIL-STD-750D:1056 (1995) MIL-STD-883G:1011 (2006) MIL-STD-202G:107G (2002) JESD22-A106B (2004) Solder Resistance T.sol = 260 5C Dwell Time= 101 seconds 3mm from the base of the epoxy bulb 11 PCS (CL=90%; LTPD=18.9%) MIL-STD-750D:2031(1995) JEITA ED-4701: 300 302 (2001) Solderability T. sol = 245 5C Dwell Time= 5 0.5 seconds (Lead Free Solder, Coverage 95% of the dipped surface) 11 PCS (CL=90%; LTPD=18.9%) MIL-STD-750D:2026 (1995) MIL-STD-883G:2003 (2006) MIL-STD-202G:208H (2002) IPC/EIA J-STD-002 (2004) Soldering Iron T. sol = 350 5C Dwell Time= 3.5 0.5 seconds 11 PCS (CL=90%; LTPD=18.9%) MIL-STD-202G:208H (2002) JEITA ED-4701:300 302 (2001) MIL-STD-750D:1026 (1995) MIL-STD-883G:1005 (2006) MIL-STD-202G:103B (2002) JEITA ED-4701:100 103 (2001) Test Environmental Test 11. Others The appearance and specifications of the product may be modified for improvement, without prior notice. 10/10 Part No. : LTL-307G-011A BNS-OD-FC002/A4