SST25VF080B-50-4C-S2AF-T - Microchip Technology, Inc.

Microchip Technology Company

Data Sheet

www.microchip.com

www.sst.com

Features:

• Single Voltage Read and Write Operations

– 2.7-3.6V

• Serial Interface Architecture

– SPI Compatible: Mode 0 and Mode 3

• High Speed Clock Frequency

– 50/66 MHz conditional (see Table 15)

- (SST25VF080B-50-xx-xxxx)

– 80 MHz

- (SST25VF080B-80-xx-xxxx)

• Superior Reliability

– Endurance: 100,000 Cycles (typical)

– Greater than 100 years Data Retention

• Low Power Consumption:

– Active Read Current: 10 mA (typical)

– Standby Current: 5 µA (typical)

• Flexible Erase Capability

– Uniform 4 KByte sectors

– Uniform 32 KByte overlay blocks

– Uniform 64 KByte overlay blocks

• Fast Erase and Byte-Program:

– Chip-Erase Time: 35 ms (typical)

– Sector-/Block-Erase Time: 18 ms (typical)

– Byte-Program Time: 7 µs (typical)

• Auto Address Increment (AAI) Programming

– Decrease total chip programming time over Byte-Pro-

gram operations

• End-of-Write Detection

– Software polling the BUSY bit in Status Register

– Busy Status readout on SO pin in AAI Mode

• Hold Pin (HOLD#)

– Suspends a serial sequence to the memory

without deselecting the device

• Write Protection (WP#)

– Enables/Disables the Lock-Down function of the status

• Software Write Protection

– Write protection through Block-Protection bits in status

• Temperature Range

– Commercial: 0°C to +70°C

– Industrial: -40°C to +85°C

• Packages Available

– 8-lead SOIC (200 mils)

– 8-lead SOIC (150 mils)

– 8-contact WSON (6mm x 5mm)

– 8-lead PDIP (300 mils)

• All devices are RoHS compliant

8 Mbit SPI Serial Flash

SST25VF080B

SST's 25 series Serial Flash family features a four-wire, SPI-compatible inter-

face that allows for a low pin-count package which occupies less board space

and ultimately lowers total system costs. The SST25VF080B devices are

enhanced with improved operating frequency which lowers power consump-

tion. SST25VF080B SPI serial flash memories are manufactured with SST's

proprietary, high-performance CMOS SuperFlash technology. The split-gate

cell design and thick-oxide tunneling injector attain better reliability and manu-

facturability compared with alternate approaches

8 Mbit SPI Serial Flash

SST25VF080B

Data Sheet

Microchip Technology Company

Product Description

SST’s 25 series Serial Flash family features a four-wire, SPI-compatible interface that allows for a low

pin-count package which occupies less board space and ultimately lowers total system costs. The

SST25VF080B devices are enhanced with improved operating frequency and lower power consump-

tion. SST25VF080B SPI serial flash memories are manufactured with SST’s proprietary, high-perfor-

mance CMOS SuperFlash technology. The split-gate cell design and thick-oxide tunneling injector

attain better reliability and manufacturability compared with alternate approaches.

The SST25VF080B devices significantly improve performance and reliability, while lowering power

consumption. The devices write (Program or Erase) with a single power supply of 2.7-3.6V for

SST25VF080B. The total energy consumed is a function of the applied voltage, current, and time of

application. Since for any given voltage range, the SuperFlash technology uses less current to pro-

gram and has a shorter erase time, the total energy consumed during any Erase or Program operation

is less than alternative flash memory technologies.

The SST25VF080B device is offered in 8-lead SOIC (200 mils), 8-lead SOIC (150 mils), 8-contact

WSON (6mm x 5mm), and 8-lead PDIP (300 mils) packages. See Figure 2 for pin assignments.

8 Mbit SPI Serial Flash

SST25VF080B

Data Sheet

Microchip Technology Company

Block Diagram

Figure 1: Functional Block Diagram

1296 B1.0

I/O Buffers

and

Data Latches

SuperFlash

Memory

X - Decoder

Control Logic

Address

Buffers

and

Latches

CE#

Y - Decoder

SCK SI SO WP# HOLD#

Serial Interface

8 Mbit SPI Serial Flash

SST25VF080B

Data Sheet

Microchip Technology Company

Pin Description

Figure 2: Pin Assignments

Table 1: Pin Description

Symbol Pin Name Functions

SCK Serial Clock To provide the timing of the serial interface.

Commands, addresses, or input data are latched on the rising edge of the clock

input, while output data is shifted out on the falling edge of the clock input.

SI Serial Data Input To transfer commands, addresses, or data serially into the device.

Inputs are latched on the rising edge of the serial clock.

SO Serial Data Output To transfer data serially out of the device.

Data is shifted out on the falling edge of the serial clock.

Outputs Flash busy status during AAI Programming when reconfigured as RY/

BY# pin. See “Hardware End-of-Write Detection” on page 13 for details.

CE# Chip Enable The device is enabled by a high to low transition on CE#. CE# must remain low

for the duration of any command sequence.

WP# Write Protect The Write Protect (WP#) pin is used to enable/disable BPL bit in the status register.

HOLD# Hold To temporarily stop serial communication with SPI flash memory without reset-

ting the device.

VDD Power Supply To provide power supply voltage: 2.7-3.6V for SST25VF080B

VSS Ground

T1.0 1296

CE#

WP#

VSS

VDD

HOLD#

SCK

Top View

1296 08-soic S2A P1.0

CE#

WP#

VSS

Top View

VDD

HOLD#

SCK

1296 08-wson QA P2.0

8-lead SOIC 8-contact WSON

CE#

WP#

VSS

VDD

HOLD#

SCK

Top View

1296 08-pdip-PA-P3.0

8-lead PDIP

8 Mbit SPI Serial Flash

SST25VF080B

Data Sheet

Microchip Technology Company

Memory Organization

The SST25VF080B SuperFlash memory array is organized in uniform 4 KByte erasable sectors with 32

KByte overlay blocks and 64 KByte overlay erasable blocks.

Device Operation

The SST25VF080B is accessed through the SPI (Serial Peripheral Interface) bus compatible protocol.

The SPI bus consist of four control lines; Chip Enable (CE#) is used to select the device, and data is

accessed through the Serial Data Input (SI), Serial Data Output (SO), and Serial Clock (SCK).

The SST25VF080B supports both Mode 0 (0,0) and Mode 3 (1,1) of SPI bus operations. The difference

between the two modes, as shown in Figure 3, is the state of the SCK signal when the bus master is in

Stand-by mode and no data is being transferred. The SCK signal is low for Mode 0 and SCK signal is

high for Mode 3. For both modes, the Serial Data In (SI) is sampled at the rising edge of the SCK clock

signal and the Serial Data Output (SO) is driven after the falling edge of the SCK clock signal.

Figure 3: SPI Protocol

1296 SPIprot.0

MODE 3

SCK

CE#

MODE 3

DON T CARE

Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

MODE 0MODE 0

HIGH IMPEDANCE

MSB

8 Mbit SPI Serial Flash

SST25VF080B

Data Sheet

Microchip Technology Company

Hold Operation

The HOLD# pin is used to pause a serial sequence underway with the SPI flash memory without reset-

ting the clocking sequence. To activate the HOLD# mode, CE# must be in active low state. The HOLD#

mode begins when the SCK active low state coincides with the falling edge of the HOLD# signal. The

HOLD mode ends when the HOLD# signal’s rising edge coincides with the SCK active low state.

If the falling edge of the HOLD# signal does not coincide with the SCK active low state, then the device

enters Hold mode when the SCK next reaches the active low state. Similarly, if the rising edge of the

HOLD# signal does not coincide with the SCK active low state, then the device exits in Hold mode

when the SCK next reaches the active low state. See Figure 4 for Hold Condition waveform.

Once the device enters Hold mode, SO will be in high-impedance state while SI and SCK can be VIL or VIH.

If CE# is driven active high during a Hold condition, it resets the internal logic of the device. As long as

HOLD# signal is low, the memory remains in the Hold condition. To resume communication with the device,

HOLD# must be driven active high, and CE# must be driven active low. See Figure 24 for Hold timing.

Figure 4: Hold Condition Waveform

Write Protection

SST25VF080B provides software Write protection. The Write Protect pin (WP#) enables or disables

the lock-down function of the status register. The Block-Protection bits (BP3, BP2, BP1, BP0, and BPL)

in the status register provide Write protection to the memory array and the status register. See Table 4

for the Block-Protection description.

Write Protect Pin (WP#)

The Write Protect (WP#) pin enables the lock-down function of the BPL bit (bit 7) in the status register.

When WP# is driven low, the execution of the Write-Status-Register (WRSR) instruction is determined by

the value of the BPL bit (see Table 2). When WP# is high, the lock-down function of the BPL bit is disabled.

Table 2: Conditions to execute Write-Status-Register (WRSR) Instruction

WP# BPL Execute WRSR Instruction

L 1 Not Allowed

L 0 Allowed

H X Allowed

T2.0 1296

Active Hold Active Hold Active

1296 HoldCond.0

SCK

HOLD#

8 Mbit SPI Serial Flash

SST25VF080B

Data Sheet

Microchip Technology Company

Status Register

The software status register provides status on whether the flash memory array is available for any

Read or Write operation, whether the device is Write enabled, and the state of the Memory Write pro-

tection. During an internal Erase or Program operation, the status register may be read only to deter-

mine the completion of an operation in progress. Table 3 describes the function of each bit in the

software status register.

Busy

The Busy bit determines whether there is an internal Erase or Program operation in progress. A “1” for

the Busy bit indicates the device is busy with an operation in progress. A “0” indicates the device is

ready for the next valid operation.

Write Enable Latch (WEL)

The Write-Enable-Latch bit indicates the status of the internal memory Write Enable Latch. If the

Write-Enable-Latch bit is set to “1”, it indicates the device is Write enabled. If the bit is set to “0” (reset),

it indicates the device is not Write enabled and does not accept any memory Write (Program/Erase)

commands. The Write-Enable-Latch bit is automatically reset under the following conditions:

•Power-up

•Write-Disable (WRDI) instruction completion

•Byte-Program instruction completion

•Auto Address Increment (AAI) programming is completed or reached its highest unpro-

tected memory address

•Sector-Erase instruction completion

•Block-Erase instruction completion

•Chip-Erase instruction completion

•Write-Status-Register instructions

Table 3: Software Status Register

Bit Name Function

Default at

Power-up Read/Write

0 BUSY 1 = Internal Write operation is in progress

0 = No internal Write operation is in progress

1 WEL 1 = Device is memory Write enabled

0 = Device is not memory Write enabled

2 BP0 Indicate current level of block write protection (See Table 4) 1 R/W

3 BP1 Indicate current level of block write protection (See Table 4) 1 R/W

4 BP2 Indicate current level of block write protection (See Table 4) 1 R/W

5 BP3 Indicate current level of block write protection (See Table 4) 0 R/W

6 AAI Auto Address Increment Programming status

1 = AAI programming mode

0 = Byte-Program mode

7 BPL 1 = BP3, BP2, BP1, BP0 are read-only bits

0 = BP3, BP2, BP1, BP0 are read/writable

0 R/W

T3.0 1296

8 Mbit SPI Serial Flash

SST25VF080B

Data Sheet

Microchip Technology Company

Auto Address Increment (AAI)

The Auto Address Increment Programming-Status bit provides status on whether the device is in AAI

programming mode or Byte-Program mode. The default at power up is Byte-Program mode.

Block Protection (BP3,BP2, BP1, BP0)

The Block-Protection (BP3, BP2, BP1, BP0) bits define the size of the memory area, as defined in

Table 4, to be software protected against any memory Write (Program or Erase) operation. The Write-

Status-Register (WRSR) instruction is used to program the BP3, BP2, BP1 and BP0 bits as long as

WP# is high or the Block-Protect-Lock (BPL) bit is 0. Chip-Erase can only be executed if Block-Protec-

tion bits are all 0. After power-up, BP3, BP2, BP1 and BP0 are set to 1.

Block Protection Lock-Down (BPL)

WP# pin driven low (VIL), enables the Block-Protection-Lock-Down (BPL) bit. When BPL is set to 1, it

prevents any further alteration of the BPL, BP3, BP2, BP1, and BP0 bits. When the WP# pin is driven

high (VIH), the BPL bit has no effect and its value is “Don’t Care”. After power-up, the BPL bit is reset to

Table 4: Software Status Register Block Protection for SST25VF080B1

1. X = Don’t Care (RESERVED) default is “0

Protection Level

Status Register Bit2

2. Default at power-up for BP2, BP1, and BP0 is ‘111’. (All Blocks Protected)

Protected Memory Address

BP3 BP2 BP1 BP0 8 Mbit

None X 0 0 0 None

Upper 1/16 X 0 0 1 F0000H-FFFFFH

Upper 1/8 X 0 1 0 E0000H-FFFFFH

Upper 1/4 X 0 1 1 C0000H-FFFFFH

Upper 1/2 X 1 0 0 80000H-FFFFFH

All Blocks X 1 0 1 00000H-FFFFFH

All Blocks X 1 1 0 00000H-FFFFFH

All Blocks X 1 1 1 00000H-FFFFFH

T4.0 1296

8 Mbit SPI Serial Flash

SST25VF080B

Data Sheet

Microchip Technology Company

Instructions

Instructions are used to read, write (Erase and Program), and configure the SST25VF080B. The

instruction bus cycles are 8 bits each for commands (Op Code), data, and addresses. Prior to execut-

ing any Byte-Program, Auto Address Increment (AAI) programming, Sector-Erase, Block-Erase, Write-

Status-Register, or Chip-Erase instructions, the Write-Enable (WREN) instruction must be executed

first. The complete list of instructions is provided in Table 5. All instructions are synchronized off a high

to low transition of CE#. Inputs will be accepted on the rising edge of SCK starting with the most signif-

icant bit. CE# must be driven low before an instruction is entered and must be driven high after the last

bit of the instruction has been shifted in (except for Read, Read-ID, and Read-Status-Register instruc-

tions). Any low to high transition on CE#, before receiving the last bit of an instruction bus cycle, will

terminate the instruction in progress and return the device to standby mode. Instruction commands

(Op Code), addresses, and data are all input from the most significant bit (MSB) first.

Table 5: Device Operation Instructions

Instruction Description Op Code Cycle1

1. One bus cycle is eight clock periods.

Address

Cycle(s)2

2. Address bits above the most significant bit of each density can be VIL or VIH.

Dummy

Cycle(s)

Data

Cycle(s)

Read Read Memory 0000 0011b (03H) 3 0 1 to ∞

High-Speed Read Read Memory at higher

speed

0000 1011b (0BH) 3 1 1 to ∞

4 KByte Sector-Erase3

3. 4KByte Sector Erase addresses: use AMS-A12, remaining addresses are don’t care but must be set either at VIL or VIH.

Erase 4 KByte of

memory array

0010 0000b (20H) 3 0 0

32 KByte Block-Erase4

4. 32KByte Block Erase addresses: use AMS-A15, remaining addresses are don’t care but must be set either at VIL or VIH.

Erase 32 KByte block

of memory array

0101 0010b (52H) 3 0 0

64 KByte Block-Erase5

5. 64KByte Block Erase addresses: use AMS-A16, remaining addresses are don’t care but must be set either at VIL or VIH.

Erase 64 KByte block

of memory array

1101 1000b (D8H) 3 0 0

Chip-Erase Erase Full Memory Array 0110 0000b (60H) or

1100 0111b (C7H)

000

Byte-Program To Program One Data Byte 0000 0010b (02H) 3 0 1

AAI-Word-Program6Auto Address Increment

Programming

1010 1101b (ADH) 3 0 2 to ∞

RDSR7Read-Status-Register 0000 0101b (05H) 0 0 1 to ∞

EWSR Enable-Write-Status-Register 0101b 0000b (50H) 0 0 0

WRSR Write-Status-Register 0000 0001b (01H) 0 0 1

WREN Write-Enable 0000 0110b (06H) 0 0 0

WRDI Write-Disable 0000 0100b (04H) 0 0 0

RDID8Read-ID 1001 0000b (90H) or

1010 1011b (ABH)

301to∞

JEDEC-ID JEDEC ID read 1001 1111b (9FH) 0 0 3 to ∞

EBSY Enable SO to output RY/BY#

status during AAI programming

0111 0000b (70H) 0 0 0

DBSY Disable SO as RY/BY#

status during AAI programming

1000 0000b (80H) 0 0 0

T5.0 1296

8 Mbit SPI Serial Flash

SST25VF080B

Data Sheet

Microchip Technology Company

Read (25/33 MHz)

The Read instruction, 03H, supports up to 25 MHz (for SST25VF080B-50-xx-xxxx) or 33 MHz (for

SST25VF080B-80-xx-xxxx) Read. The device outputs the data starting from the specified address

location. The data output stream is continuous through all addresses until terminated by a low to high

transition on CE#. The internal address pointer will automatically increment until the highest memory

address is reached. Once the highest memory address is reached, the address pointer will automati-

cally increment to the beginning (wrap-around) of the address space. Once the data from address

location 1FFFFFH has been read, the next output will be from address location 000000H.

The Read instruction is initiated by executing an 8-bit command, 03H, followed by address bits [A23-

A0]. CE# must remain active low for the duration of the Read cycle. See Figure 5 for the Read

sequence.

Figure 5: Read Sequence

6. To continue programming to the next sequential address location, enter the 8-bit command, ADH, followed by 2 bytes of

data to be programmed. Data Byte 0 will be programmed into the initial address [A23-A1] with A0=0, Data Byte 1 will be

programmed into the

initial address [A23-A1] with A0=1.

7. The Read-Status-Register is continuous with ongoing clock cycles until terminated by a low to high transition on CE#.

8. Manufacturer’s ID is read with A0=0, and Device ID is read with A0=1. All other address bits are 00H. The Manufac-

turer’s ID and device ID output stream is continuous until terminated by a low-to-high transition on CE#.

1296 ReadSeq 0.0

CE#

SCK

ADD.

012345678

ADD. ADD.

HIGH IMPEDANCE

15 16 23 24 31 32 39 40 7047 48 55 56 63 64

N+2 N+3 N+4N N+1

DOUT

MSB MSB

MSB

MODE 0

MODE 3

DOUT DOUT DOUT DOUT

8 Mbit SPI Serial Flash

SST25VF080B

Data Sheet

Microchip Technology Company

High-Speed-Read (66/80 MHz)

The High-Speed-Read instruction supporting up to 66 MHz (for SST25VF080B-50-xx-xxxx) or 80 MHz

(for SST25VF040B-80-xx-xxxx) Read is initiated by executing an 8-bit command, 0BH, followed by

address bits [A23-A0] and a dummy byte. CE# must remain active low for the duration of the High-

Speed-Read cycle. See Figure 6 for the High-Speed-Read sequence.

Following a dummy cycle, the High-Speed-Read instruction outputs the data starting from the speci-

fied address location. The data output stream is continuous through all addresses until terminated by a

low to high transition on CE#. The internal address pointer will automatically increment until the high-

est memory address is reached. Once the highest memory address is reached, the address pointer

will automatically increment to the beginning (wrap-around) of the address space. Once the data from

address location FFFFFH has been read, the next output will be from address location 00000H.

Figure 6: High-Speed-Read Sequence

1296 HSRdSeq.0

CE#

SCK

ADD.

012345678

ADD. ADD.0B

HIGH IMPEDANCE

15 16 23 24 31 32 39 40 47 48 55 56 63 64

N+2 N+3 N+4

NN+1

MSB

MODE 0

MODE 3

DOUT DOUT DOUT DOUT

71 72

DOUT

Note: X = Dummy Byte: 8 Clocks Input Dummy Cycle (VIL or VIH)

8 Mbit SPI Serial Flash

SST25VF080B

Data Sheet

Microchip Technology Company

Byte-Program

The Byte-Program instruction programs the bits in the selected byte to the desired data. The selected

byte must be in the erased state (FFH) when initiating a Program operation. A Byte-Program instruction

applied to a protected memory area will be ignored.

Prior to any Write operation, the Write-Enable (WREN) instruction must be executed. CE# must remain

active low for the duration of the Byte-Program instruction. The Byte-Program instruction is initiated by

executing an 8-bit command, 02H, followed by address bits [A23-A0]. Following the address, the data is

input in order from MSB (bit 7) to LSB (bit 0). CE# must be driven high before the instruction is exe-

cuted. The user may poll the Busy bit in the software status register or wait TBP for the completion of

the internal self-timed Byte-Program operation. See Figure 7 for the Byte-Program sequence.

Figure 7: Byte-Program Sequence

1296 ByteProg.0

CE#

SCK

ADD.

012345678

ADD. ADD. DIN

HIGH IMPEDANCE

15 16 23 24 31 32 39

MODE 0

MODE 3

MSBMSB

MSB LSB

8 Mbit SPI Serial Flash

SST25VF080B

Data Sheet

Microchip Technology Company

Auto Address Increment (AAI) Word-Program

The AAI program instruction allows multiple bytes of data to be programmed without re-issuing the

next sequential address location. This feature decreases total programming time when multiple bytes

or entire memory array is to be programmed. An AAI Word program instruction pointing to a protected

memory area will be ignored. The selected address range must be in the erased state (FFH) when ini-

tiating an AAI Word Program operation. While within AAI Word Programming sequence, only the fol-

lowing instructions are valid: for software end-of-write detection—AAI Word (ADH), WRDI (04H), and

RDSR (05H); for hardware end-of-write detection—AAI Word (ADH) and WRDI (04H). There are three

options to determine the completion of each AAI Word program cycle: hardware detection by reading

the Serial Output, software detection by polling the BUSY bit in the software status register, or wait TBP.

Refer to“End-of-Write Detection” for details.

Prior to any write operation, the Write-Enable (WREN) instruction must be executed. Initiate the AAI

Word Program instruction by executing an 8-bit command, ADH, followed by address bits [A23-A0]. Fol-

lowing the addresses, two bytes of data are input sequentially, each one from MSB (Bit 7) to LSB (Bit

0). The first byte of data (D0) is programmed into the initial address [A23-A1] with A0=0, the second

byte of Data (D1) is programmed into the initial address [A23-A1] with A0=1. CE# must be driven high

before executing the AAI Word Program instruction. Check the BUSY status before entering the next

valid command. Once the device indicates it is no longer busy, data for the next two sequential

addresses may be programmed, followed by the next two, and so on.

When programming the last desired word, or the highest unprotected memory address, check the busy

status using either the hardware or software (RDSR instruction) method to check for program comple-

tion. Once programming is complete, use the applicable method to terminate AAI. If the device is in

Software End-of-Write Detection mode, execute the Write-Disable (WRDI) instruction, 04H. If the

device is in AAI Hardware End-of-Write Detection mode, execute the Write-Disable (WRDI) instruction,

04H, followed by the 8-bit DBSY command, 80H. There is no wrap mode during AAI programming

once the highest unprotected memory address is reached. See Figures 10 and 11 for the AAI Word

programming sequence.

End-of-Write Detection

There are three methods to determine completion of a program cycle during AAI Word programming:

hardware detection by reading the Serial Output, software detection by polling the BUSY bit in the Soft-

ware Status Register, or wait TBP. The Hardware End-of-Write detection method is described in the

section below.

Hardware End-of-Write Detection

The Hardware End-of-Write detection method eliminates the overhead of polling the Busy bit in the

Software Status Register during an AAI Word program operation. The 8-bit command, 70H, configures

the Serial Output (SO) pin to indicate Flash Busy status during AAI Word programming. (see Figure 8)

The 8-bit command, 70H, must be executed prior to initiating an AAI Word-Program instruction. Once

an internal programming operation begins, asserting CE# will immediately drive the status of the inter-

nal flash status on the SO pin. A ‘0’ indicates the device is busy and a ‘1’ indicates the device is ready

for the next instruction. De-asserting CE# will return the SO pin to tri-state. While in AAI and Hardware

End-of-Write detection mode, the only valid instructions are AAI Word (ADH) and WRDI (04H).

To exit AAI Hardware End-of-Write detection, first execute WRDI instruction, 04H, to reset the Write-

Enable-Latch bit (WEL=0) and AAI bit. Then execute the 8-bit DBSY command, 80H, to disable RY/

BY# status during the AAI command. See Figures 9 and 10.

8 Mbit SPI Serial Flash

SST25VF080B

Data Sheet

Microchip Technology Company

Figure 8: Enable SO as Hardware RY/BY# During AAI Programming

Figure 9: Disable SO as Hardware RY/BY# During AAI Programming

CE#

SCK

01234567

HIGH IMPEDANCE

MODE 0

MODE 3

1271 EnableSO.0

MSB

CE#

SCK

01234567

HIGH IMPEDANCE

MODE 0

MODE 3

1271 DisableSO.0

MSB

8 Mbit SPI Serial Flash

SST25VF080B

Data Sheet

Microchip Technology Company

Figure 10:Auto Address Increment (AAI) Word-Program Sequence with

Hardware End-of-Write Detection

Figure 11:Auto Address Increment (AAI) Word-Program Sequence with

Software End-of-Write Detection

CE#

SCK

1296 AAI.HW.3

Check for Flash Busy Status to load next valid1command

Load AAI command, Address, 2 bytes data

Note: 1. Valid commands during AAI programming: AAI command or WRDI command

2. User must configure the SO pin to output Flash Busy status during AAI programming

AAA

AD D0 AD

MODE 3

MODE 0

D1 D2 D3

WREN

EBSY

07078 32 4715 16 23 24 31 04039 7 8 15 16 23

DOUT

WRDI followed by DBSY

to exit AAI Mode

WRDI RDSR

7015

780

DBSY

CE# cont.

SI cont.

SCK cont.

SO cont.

Last 2

Data Bytes

AD Dn-1 Dn

7 8 15 16 23

Check for Flash Busy Status to load next valid1command

078 32 4715 16 23 24 31 04039 7 8 15 16 23 7 8 15 16 23 70 157800

CE#

SCK

SO DOUT

MODE 3

MODE 0

1296 AAI.SW.3

Note: 1. Valid commands during AAI programming: AAI command, RDSR command, or WRDI command

Wait TBP or poll Software Status

Last 2

Data Bytes

WRDI to exit

AAI Mode

Load AAI command, Address, 2 bytes data

AAAAD D0 ADD1 D2 D3 AD Dn-1 Dn

WRDI

RDSR

8 Mbit SPI Serial Flash

SST25VF080B

Data Sheet

Microchip Technology Company

4-KByte Sector-Erase

The Sector-Erase instruction clears all bits in the selected 4 KByte sector to FFH. A Sector-Erase

instruction applied to a protected memory area will be ignored. Prior to any Write operation, the Write-

Enable (WREN) instruction must be executed. CE# must remain active low for the duration of any com-

mand sequence. The Sector-Erase instruction is initiated by executing an 8-bit command, 20H, fol-

lowed by address bits [A23-A0]. Address bits [AMS-A12](A

MS = Most Significant address) are used to

determine the sector address (SAX), remaining address bits can be VIL or VIH. CE# must be driven high

before the instruction is executed. The user may poll the Busy bit in the software status register or wait

TSE for the completion of the internal self-timed Sector-Erase cycle. See Figure 12 for the Sector-

Erase sequence.

Figure 12:Sector-Erase Sequence

CE#

SCK

ADD.

012345678

ADD. ADD.

HIGH IMPEDANCE

15 16 23 24 31

MODE 0

MODE 3

1296 SecErase.0

MSBMSB

8 Mbit SPI Serial Flash

SST25VF080B

Data Sheet

Microchip Technology Company

32-KByte and 64-KByte Block-Erase

The 32-KByte Block-Erase instruction clears all bits in the selected 32 KByte block to FFH. A Block-

Erase instruction applied to a protected memory area will be ignored. The 64-KByte Block-Erase instruc-

tion clears all bits in the selected 64 KByte block to FFH. A Block-Erase instruction applied to a protected mem-

ory area will be ignored. Prior to any Write operation, the Write-Enable (WREN) instruction must be executed.

CE# must remain active low for the duration of any command sequence. The 32-KByte Block-Erase

instruction is initiated by executing an 8-bit command, 52H, followed by address bits [A23-A0]. Address

bits [AMS-A15](A

MS = Most Significant Address) are used to determine block address (BAX), remaining

address bits can be VIL or VIH. CE# must be driven high before the instruction is executed. The 64-KByte Block-

Erase instruction is initiated by executing an 8-bit command D8H, followed by address bits [A23-A0]. Address bits

[AMS-A15] are used to determine block address (BAX), remaining address bits can be VIL or VIH. CE# must be

driven high before the instruction is executed. The user may poll the Busy bit in the software status register or

wait TBE for the completion of the internal self-timed 32-KByte Block-Erase or 64-KByte Block-Erase

cycles. See Figures 13 and 14 for the 32-KByte Block-Erase and 64-KByte Block-Erase sequences.

Figure 13:32-KByte Block-Erase Sequence

Figure 14:64-KByte Block-Erase Sequence

CE#

SCK

ADDR

012345678

ADDR ADDR

HIGH IMPEDANCE

15 16 23 24 31

MODE 0

MODE 3

1296 32KBklEr.0

MSB MSB

CE#

SCK

ADDR

012345678

ADDR ADDR

HIGH IMPEDANCE

15 16 23 24 31

MODE 0

MODE 3

1296 63KBlkEr.0

MSB MSB

8 Mbit SPI Serial Flash

SST25VF080B

Data Sheet

Microchip Technology Company

Chip-Erase

The Chip-Erase instruction clears all bits in the device to FFH. A Chip-Erase instruction will be ignored

if any of the memory area is protected. Prior to any Write operation, the Write-Enable (WREN) instruction

must be executed. CE# must remain active low for the duration of the Chip-Erase instruction sequence.

The Chip-Erase instruction is initiated by executing an 8-bit command, 60H or C7H. CE# must be driven

high before the instruction is executed. The user may poll the Busy bit in the software status register or wait

TCE for the completion of the internal self-timed Chip-Erase cycle. See Figure 15 for the Chip-Erase

sequence.

Figure 15:Chip-Erase Sequence

Read-Status-Register (RDSR)

The Read-Status-Register (RDSR) instruction allows reading of the status register. The status register

may be read at any time even during a Write (Program/Erase) operation. When a Write operation is in

progress, the Busy bit may be checked before sending any new commands to assure that the new

commands are properly received by the device. CE# must be driven low before the RDSR instruction is

entered and remain low until the status data is read. Read-Status-Register is continuous with ongoing

clock cycles until it is terminated by a low to high transition of the CE#. See Figure 16 for the RDSR

instruction sequence.

Figure 16:Read-Status-Register (RDSR) Sequence

CE#

SCK

01234567

60 or C7

HIGH IMPEDANCE

MODE 0

MODE 3

1296 ChEr.0

MSB

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14

1296 RDSRseq.0

MODE 3

SCK

CE#

Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

MODE 0

HIGH IMPEDANCE

Status

MSB

8 Mbit SPI Serial Flash

SST25VF080B

Data Sheet

Microchip Technology Company

Write-Enable (WREN)

The Write-Enable (WREN) instruction sets the Write-Enable-Latch bit in the Status Register to 1 allow-

ing Write operations to occur. The WREN instruction must be executed prior to any Write (Program/

Erase) operation. The WREN instruction may also be used to allow execution of the Write-Status-Reg-

ister (WRSR) instruction; however, the Write-Enable-Latch bit in the Status Register will be cleared

upon the rising edge CE# of the WRSR instruction. CE# must be driven high before the WREN instruc-

tion is executed.

Figure 17:Write Enable (WREN) Sequence

Write-Disable (WRDI)

The Write-Disable (WRDI) instruction resets the Write-Enable-Latch bit and AAI bit to 0 disabling any

new Write operations from occurring. The WRDI instruction will not terminate any programming opera-

tion in progress. Any program operation in progress may continue up to TBP after executing the WRDI

instruction. CE# must be driven high before the WRDI instruction is executed.

Figure 18:Write Disable (WRDI) Sequence

CE#

SCK

01234567

HIGH IMPEDANCE

MODE 0

MODE 3

1296 WREN.0

MSB

CE#

SCK

01234567

HIGH IMPEDANCE

MODE 0

MODE 3

1296 WRDI.0

MSB

8 Mbit SPI Serial Flash

SST25VF080B

Data Sheet

Microchip Technology Company

Enable-Write-Status-Register (EWSR)

The Enable-Write-Status-Register (EWSR) instruction arms the Write-Status-Register (WRSR)

instruction and opens the status register for alteration. The Write-Status-Register instruction must be

executed immediately after the execution of the Enable-Write-Status-Register instruction. This two-

step instruction sequence of the EWSR instruction followed by the WRSR instruction works like SDP

(software data protection) command structure which prevents any accidental alteration of the status

high before the EWSR instruction is executed.

Write-Status-Register (WRSR)

The Write-Status-Register instruction writes new values to the BP3, BP2, BP1, BP0, and BPL bits of

the status register. CE# must be driven low before the command sequence of the WRSR instruction is

entered and driven high before the WRSR instruction is executed. See Figure 19 for EWSR or WREN

and WRSR instruction sequences.

Executing the Write-Status-Register instruction will be ignored when WP# is low and BPL bit is set to

“1”. When the WP# is low, the BPL bit can only be set from “0” to “1” to lock-down the status register,

but cannot be reset from “1” to “0”. When WP# is high, the lock-down function of the BPL bit is disabled

and the BPL, BP0, and BP1 and BP2 bits in the status register can all be changed. As long as BPL bit

is set to 0 or WP# pin is driven high (VIH) prior to the low-to-high transition of the CE# pin at the end of

the WRSR instruction, the bits in the status register can all be altered by the WRSR instruction. In this

case, a single WRSR instruction can set the BPL bit to “1” to lock down the status register as well as

altering the BP0, BP1, and BP2 bits at the same time. See Table 2 for a summary description of WP#

and BPL functions.

Figure 19:Enable-Write-Status-Register (EWSR) or Write-Enable (WREN) and

Write-Status-Register (WRSR) Sequence

1296 EWSR.0

MODE 3

HIGH IMPEDANCE

MODE 0

STATUS

76543210

MSBMSBMSB

MODE 3

SCK

CE#

MODE 0

50 or 06

0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

8 Mbit SPI Serial Flash

SST25VF080B

Data Sheet

Microchip Technology Company

JEDEC Read-ID

The JEDEC Read-ID instruction identifies the device as SST25VF080B and the manufacturer as SST.

The device information can be read from executing the 8-bit command, 9FH. Following the JEDEC

Read-ID instruction, the 8-bit manufacturer’s ID, BFH, is output from the device. After that, a 16-bit

device ID is shifted out on the SO pin. Byte 1, BFH, identifies the manufacturer as SST. Byte 2, 25H,

identifies the memory type as SPI Serial Flash. Byte 3, 8EH, identifies the device as SST25VF080B.

The instruction sequence is shown in Figure 20. The JEDEC Read ID instruction is terminated by a low

to high transition on CE# at any time during data output.

Figure 20:JEDEC Read-ID Sequence

Table 6: JEDEC Read-ID Data

Manufacturer’s ID Device ID

Memory Type Memory Capacity

Byte1 Byte 2 Byte 3

BFH 25H 8EH

T6.0 1296

25 8E

1296 JEDECID.1

CE#

SCK

012345678

HIGH IMPEDANCE

15 1614 28 29 30 31

MODE 3

MODE 0

MSBMSB

9 10111213 1718 32 34

19 20 21 22 23 3324 25 26 27

8 Mbit SPI Serial Flash

SST25VF080B

Data Sheet

Microchip Technology Company

Read-ID (RDID)

The Read-ID instruction (RDID) identifies the devices as SST25VF080B and manufacturer as SST.

This command is backward compatible and should be used as default device identification when multi-

ple versions of SPI Serial Flash devices are used in a design. The device information can be read from

executing an 8-bit command, 90H or ABH, followed by address bits [A23-A0]. Following the Read-ID

instruction, the manufacturer’s ID is located in address 00000H and the device ID is located in address

00001H. Once the device is in Read-ID mode, the manufacturer’s and device ID output data toggles

between address 00000H and 00001H until terminated by a low to high transition on CE#.

Refer to Tables 6 and 7 for device identification data.

Figure 21:Read-ID Sequence

Table 7: Product Identification

Address Data

Manufacturer’s ID 00000H BFH

Device ID

SST25VF080B 00001H 8EH

T7.0 1296

1265 RdID.0

CE#

SCK

012345678

00 ADD1

90 or AB

HIGH IMPEDANCE

15 16 23 24 31 32 39 40 47 48 55 56 63

BF Device ID BF Device ID

HIGH

IMPEDANCE

MODE 3

MODE 0

MSB MSB

MSB

Note: The manufacturer’s and device ID output stream is continuous until terminated by a low-to-high transition on

CE#.

Device ID = 8EH for SST25VF080B

100H will output the manufacture’s ID first and 01H will output device ID first before toggling between the two.

8 Mbit SPI Serial Flash

SST25VF080B

Data Sheet

Microchip Technology Company

Electrical Specifications

Absolute Maximum Stress Ratings (Applied conditions greater than those listed under “Absolute

Maximum Stress Ratings” may cause permanent damage to the device. This is a stress rating only and

functional operation of the device at these conditions or conditions greater than those defined in the

operational sections of this data sheet is not implied. Exposure to absolute maximum stress rating con-

ditions may affect device reliability.)

Temperature Under Bias .............................................. -55°C to +125°C

Storage Temperature................................................. -65°C to +150°C

D. C. Voltage on Any Pin to Ground Potential .............................-0.5V to VDD+0.5V

Transient Voltage (<20 ns) on Any Pin to Ground Potential ..................-2.0V to VDD+2.0V

Package Power Dissipation Capability (TA= 25°C)................................... 1.0W

Surface Mount Solder Reflow Temperature ...........................260°C for 10 seconds

Output Short Circuit Current1................................................... 50mA

1. Output shorted for no more than one second. No more than one output shorted at a time.

Table 8: Operating Range

Range Ambient Temp VDD

Commercial 0°C to +70°C 2.7-3.6V

Industrial -40°C to +85°C 2.7-3.6V

T8.1 1296

Table 9: AC Conditions of Test1

1. See Figures 26 and 27

Input Rise/Fall Time Output Load

5ns CL=30pF

T9.1 1296

Table 10:DC Operating Characteristics (SST25VF080B-50-xx-xxxx)

Symbol Parameter

Limits

Test ConditionsMin Max Units

IDDR Read Current 10 mA CE#=0.1 VDD/0.9 VDD@25 MHz, SO=open

IDDR2 Read Current 15 mA CE#=0.1 VDD/0.9 VDD@50 MHz, SO=open

IDDW Program and Erase Current 30 mA CE#=VDD

ISB Standby Current 20 µA CE#=VDD,V

IN=VDD or VSS

ILI Input Leakage Current 1 µA VIN=GND to VDD,V

DD=VDD Max

ILO Output Leakage Current 1 µA VOUT=GND to VDD,V

DD=VDD Max

VIL Input Low Voltage 0.8 V VDD=VDD Min

VIH Input High Voltage 0.7 VDD VV

DD=VDD Max

VOL Output Low Voltage 0.2 V IOL=100 µA, VDD=VDD Min

VOL2 Output Low Voltage 0.4 V IOL=1.6 mA, VDD=VDD Min

VOH Output High Voltage VDD-0.2 V IOH=-100 µA, VDD=VDD Min

T10.0 1296

8 Mbit SPI Serial Flash

SST25VF080B

Data Sheet

Microchip Technology Company

Table 11:DC Operating Characteristics (SST25VF080B-80-xx-xxxx)

Symbol Parameter

Limits

Test ConditionsMin Max Units

IDDR Read Current 12 mA CE#=0.1 VDD/0.9 VDD@33 MHz, SO=open

IDDR3 Read Current 20 mA CE#=0.1 VDD/0.9 VDD@80 MHz, SO=open

IDDW Program and Erase Current 30 mA CE#=VDD

ISB Standby Current 20 µA CE#=VDD,V

IN=VDD or VSS

ILI Input Leakage Current 1 µA VIN=GND to VDD,V

DD=VDD Max

ILO Output Leakage Current 1 µA VOUT=GND to VDD,V

DD=VDD Max

VIL Input Low Voltage 0.8 V VDD=VDD Min

VIH Input High Voltage 0.7 VDD VV

DD=VDD Max

VOL Output Low Voltage 0.2 V IOL=100 µA, VDD=VDD Min

VOL2 Output Low Voltage 0.4 V IOL=1.6 mA, VDD=VDD Min

VOH Output High Voltage VDD-0.2 V IOH=-100 µA, VDD=VDD Min

T11.0 1296

Table 12:Recommended System Power-up Timings

Symbol Parameter Minimum Units

TPU-READ1

1. This parameter is measured only for initial qualification and after a design or process change that could affect this

parameter.

VDD Min to Read Operation 10 µs

TPU-WRITE1VDD Min to Write Operation 10 µs

T12.0 1296

Table 13:Capacitance (TA= 25°C, f=1 Mhz, other pins open)

Parameter Description Test Condition Maximum

COUT1

1. This parameter is measured only for initial qualification and after a design or process change that could affect this

parameter.

Output Pin Capacitance VOUT =0V 12pF

CIN1Input Capacitance VIN =0V 6pF

T13.0 1296

Table 14:Reliability Characteristics

Symbol Parameter Minimum Specification Units Test Method

NEND1

1. This parameter is measured only for initial qualification and after a design or process change that could affect this

parameter.

Endurance 10,000 Cycles JEDEC Standard A117

TDR1Data Retention 100 Years JEDEC Standard A103

ILTH1Latch Up 100 + IDD mA JEDEC Standard 78

T14.0 1296

8 Mbit SPI Serial Flash

SST25VF080B

Data Sheet

Microchip Technology Company

Table 15:AC Operating Characteristics (SST25VF080B-50-xx-xxxx)

25 MHz 50 MHz 66 MHz1,2

Symbo

l Parameter Min Max Min Max Min Max Units

FCLK3Serial Clock Frequency 25 50 66 MHz

TSCKH Serial Clock High Time 18 9 7 ns

TSCKL Serial Clock Low Time 18 9 7 ns

TSCKR4Serial Clock Rise Time (Slew

Rate)

0.1 0.1 0.1 V/ns

TSCKF Serial Clock Fall Time (Slew

Rate)

0.1 0.1 0.1 V/ns

TCES5CE# Active Setup Time 10 5 4 ns

TCEH5CE# Active Hold Time 10 5 4 ns

TCHS5CE# Not Active Setup Time 10 5 4 ns

TCHH5CE# Not Active Hold Time 10 5 4 ns

TCPH CE# High Time 100 50 100 ns

TCHZ CE# High to High-Z Output 15 8 6 ns

TCLZ SCK Low to Low-Z Output 0 0 0 ns

TDS Data In Setup Time 5 2 2 ns

TDH Data In Hold Time 5 5 3 ns

THLS HOLD# Low Setup Time 10 5 4 ns

THHS HOLD# High Setup Time 10 5 4 ns

THLH HOLD# Low Hold Time 10 5 4 ns

THHH HOLD# High Hold Time 10 5 4 ns

THZ HOLD# Low to High-Z Output 20 8 8 ns

TLZ HOLD# High to Low-Z Output 15 8 8 ns

TOH Output Hold from SCK Change 0 0 0 ns

TVOutput Valid from SCK 15 8 6 ns

TSE Sector-Erase 25 25 25 ms

TBE Block-Erase 25 25 25 ms

TSCE Chip-Erase 50 50 50 ms

TBP Byte-Program 10 10 10 µs

T15.0 1296

1. VDD =3.0-3.6V,CL=15pF

2. Characterized, but not fully tested

3. Maximum clock frequency for Read Instruction, 03H, is 25 MHz

4. Maximum Rise and Fall time may be limited by TSCKH and TSCKL requirements

5. Relative to SCK.

8 Mbit SPI Serial Flash

SST25VF080B

Data Sheet

Microchip Technology Company

Table 16:AC Operating Characteristics (SST25VF080B-80-xx-xxxx)

33 MHz 80 MHz

Symbol Parameter Min Max Min Max Units

FCLK1Serial Clock Frequency 33 80 MHz

TSCKH Serial Clock High Time 13 6 ns

TSCKL Serial Clock Low Time 13 6 ns

TSCKR2Serial Clock Rise Time (Slew Rate) 0.1 0.1 V/ns

TSCKF Serial Clock Fall Time (Slew Rate) 0.1 0.1 V/ns

TCES3CE# Active Setup Time 5 5 ns

TCEH5CE# Active Hold Time 5 5 ns

TCHS5CE# Not Active Setup Time 5 5 ns

TCHH5CE# Not Active Hold Time 5 5 ns

TCPH CE# High Time 50 50 ns

TCHZ CE# High to High-Z Output 7 7 ns

TCLZ SCK Low to Low-Z Output 0 0 ns

TDS Data In Setup Time 2 2 ns

TDH Data In Hold Time 4 4 ns

THLS HOLD# Low Setup Time 5 5 ns

THHS HOLD# High Setup Time 5 5 ns

THLH HOLD# Low Hold Time 5 5 ns

THHH HOLD# High Hold Time 5 5 ns

THZ HOLD# Low to High-Z Output 7 7 ns

TLZ HOLD# High to Low-Z Output 7 7 ns

TOH Output Hold from SCK Change 0 0 ns

TVOutput Valid from SCK 10 6 ns

TSE Sector-Erase 25 25 ms

TBE Block-Erase 25 25 ms

TSCE Chip-Erase 50 50 ms

TBP Byte-Program 10 10 µs

T16.0 1296

1. Maximum clock frequency for Read Instruction, 03H, is 33 MHz

2. Maximum Rise and Fall time may be limited by TSCKH and TSCKL requirements

3. Relative to SCK.

8 Mbit SPI Serial Flash

SST25VF080B

Data Sheet

Microchip Technology Company

Figure 22:Serial Input Timing Diagram

Figure 23:Serial Output Timing Diagram

Figure 24:Hold Timing Diagram

HIGH-Z HIGH-Z

CE#

SCK

MSB LSB

TDS TDH

TCHH TCES TCEH TCHS

TSCKR

TSCKF

TCPH

1296 SerIn.0

1296 SerOut.0

CE#

SCK

MSB

TCLZ

TSCKH

TCHZ

TOH

TSCKL

LSB

THZ TLZ

THHH THLS THHS

1296 Hold.0

HOLD#

CE#

SCK

THLH

8 Mbit SPI Serial Flash

SST25VF080B

Data Sheet

Microchip Technology Company

Figure 25:Power-up Timing Diagram

Figure 26:AC Input/Output Reference Waveforms

Time

VDD Min

VDD Max

VDD

Device fully accessible

TPU-READ

TPU-WRITE

Chip selection is not allowed.

Commands may not be accepted or properly

interpreted by the device.

1296 PwrUp.0

1296 IORef.0

REFERENCE POINTS OUTPUTINPUT

VHT

VLT

VHT

VLT

VIHT

VILT

AC test inputs are driven at VIHT (0.9VDD) for a logic “1” and VILT (0.1VDD) for a logic “0”. Measure-

ment reference points for inputs and outputs are VHT (0.6VDD) and VLT (0.4VDD). Input rise and fall

times (10% ↔90%) are <5 ns.

Note: VHT -V

HIGH Test

VLT -V

LOW Test

VIHT -V

INPUT HIGH Test

VILT -V

INPUT LOW Test

8 Mbit SPI Serial Flash

SST25VF080B

Data Sheet

Microchip Technology Company

Figure 27:A Test Load Example

1296 TstLd.0

TO TESTER

TO DUT

8 Mbit SPI Serial Flash

SST25VF080B

Data Sheet

Microchip Technology Company

Product Ordering Information

SST 25 VF 080B - 80 - 4C - S2AE

XX XX XXXX - XX - XX -XXXX

Environmental Attribute

E1= non-Pb / non-Sn contact (lead) finish

F2= non-Pb / non-Sn contact (lead) finish:

Nickel plating with Gold top (outer) layer

Package Modifier

A = 8 leads or contacts

Package Type

S = SOIC 150 mil body width

S2 = SOIC 200 mil body width

Q = WSON

P= PDIP 300 mil body width

Temperature Range

C = Commercial = 0°C to +70°C

I = Industrial = -40°C to +85°C

Minimum Endurance

4 = 10,000 cycles

Operating Frequency

50 = 50 MHz

80 = 80 MHz

Device Density

080 = 8 Mbit

Voltage

V = 2.7-3.6V

Product Series

25 = Serial Peripheral Interface flash

memory

1. Environmental suffix “E” denotes non-Pb solder.

SST non-Pb solder devices are “RoHS Compliant”.

2. Environmental suffix “F” denotes non-Pb/non-SN

solder. SST non-Pb/non-Sn solder devices are

“RoHS Compliant”.

8 Mbit SPI Serial Flash

SST25VF080B

Data Sheet

Microchip Technology Company

Valid Combinations for SST25VF080B

SST25VF080B-50-4C-S2AF SST25VF080B-50-4C-QAF SST25VF080B-50-4C-PAE

SST25VF080B-50-4I-S2AF SST25VF080B-50-4I-QAF

SST25VF080B-80-4C-S2AE SST25VF080B-80-4C-QAE

SST25VF080B-80-4I-S2AE SST25VF080B-80-4I-QAE

SST25VF080B-80-4C-SAE

SST25VF080B-80-4I-SAE

Note:Valid combinations are those products in mass production or will be in mass production. Consult your SST sales rep-

resentative to confirm availability of valid combinations and to determine availability of new combinations.

8 Mbit SPI Serial Flash

SST25VF080B

Data Sheet

Microchip Technology Company

Packaging Diagrams

Figure 28: 8-lead Small Outline Integrated Circuit (SOIC) 200 mil body width (5.2mm x 8mm)

SST Package Code: S2A

2.16

1.75

08-soic-EIAJ-S2A-3

Note: 1. All linear dimensions are in millimeters (max/min).

2. Coplanarity: 0.1 mm

3. Maximum allowable mold flash is 0.15 mm at the package ends and 0.25 mm between leads.

TOP VIEW SIDE VIEW

END VIEW

5.40

5.15

8.10

7.70

5.40

5.15

Pin #1

Identifier

0.50

0.35

1.27 BSC

0.25

0.05

0.25

0.19

0.80

0.50

0°

8°

1mm

8 Mbit SPI Serial Flash

SST25VF080B

Data Sheet

Microchip Technology Company

Figure 29: 8-lead Small Outline Integrated Circuit (SOIC) 150 mil body width (4.9mm x 6mm)

SST Package Code: SA

08-soic-5x6-SA-8

Note: 1. Complies with JEDEC publication 95 MS-012 AA dimensions,

although some dimensions may be more stringent.

2. All linear dimensions are in millimeters (max/min).

3. Coplanarity: 0.1 mm

4. Maximum allowable mold flash is 0.15 mm at the package ends and 0.25 mm between leads.

TOP VIEW SIDE VIEW

END VIEW

5.0

4.8

6.20

5.80

4.00

3.80

Pin #1

Identifier

0.51

0.33

1.27 BSC

0.25

0.10

1.75

1.35

7°

4 places

0.25

0.19

1.27

0.40

45° 7°

4 places

0°

8°

1mm

8 Mbit SPI Serial Flash

SST25VF080B

Data Sheet

Microchip Technology Company

Figure 30:8-contact Very-very-thin Small Outline No-lead (WSON)

SST Package Code: QA

Note: 1. All linear dimensions are in millimeters (max/min).

2. Untoleranced dimensions (shown with box surround)

are nominal target dimensions.

3. The external paddle is electrically connected to the

die back-side and possibly to certain VSS leads.

This paddle can be soldered to the PC board;

it is suggested to connect this paddle to the VSS of the unit.

Connection of this paddle to any other voltage potential can

result in shorts and/or electrical malfunction of the device.

8-wson-5x6-QA-9.0

4.0

1.27 BSC

Pin #1

0.48

0.35

0.076

3.4

5.00 0 .10

6.00 0.10 0.05 Max

0.70

0.50

0.80

0.70

0.80

0.70

Pin #1

Corner

TOPVIEW BOTTOMVIEW

CROSS SECTION

SIDE VIEW

1mm

0.2

8 Mbit SPI Serial Flash

SST25VF080B

Data Sheet

Microchip Technology Company

Figure 31:8-lead Plastic Dual In-Line Pins (PDIP)

SST Package Code: PA

8-pdip-PA-1.0

Note: 1. Complies with JEDEC publication 95 MS-001 BA dimensions, although some dimensions may be more stringent.

2. All linear dimensions are in inches (min/max).

3. Dimensions do not include mold flash. Maximum allowable mold flash is .010 inches.

TOP VIEW

SIDE VIEW END VIEW

0.25 inches

0.355

0.400

0.245

0.260

0.100 BSC

0.056

0.064

0.014

0.022

0.126

0.142

0.015 min

0.115

0.150

0.300

0.325

0.335

0.375

0.008

0.014

Pin 1

8 Mbit SPI Serial Flash

SST25VF080B

Data Sheet

Microchip Technology Company

Table 17:Revision History

Number Description Date

00 •Initial release of data sheet Sep 2005

01 •Migrated document to a Data Sheet

•Updated Surface Mount Solder Reflow Temperature information

Jan 2006

02 •Updated Features

•Updated Table 5 on page 9

•Updated “High-Speed-Read (66/80 MHz)” on page 11

•Updated Table 15 on page 25

Jun 2007

03 •Modified “Features”, “Product Description”, “Pin Description”, “Product

Ordering Information”, and “Packaging Diagrams” to include the PAE

package.

•Updated Figures 10 and 11 on page 15.

Mar 2009

04 •Added 80 MHz High Speed Clock Frequency to Features

•Removed Maximum Frequency from Table 5 on page 9

•Edited “Read (25/33 MHz)” on page 10 and “High-Speed-Read (66/80

MHz)” on page 11.

•Added Table 11 on page 24 and Table 16 on page 26

•Edited Product Ordering Information

•Added Valid Combinations SST25VF080B-80-4C-S2AE,

SST25VF080B-80-4I-S2AE, SST25VF080B-80-4C-QAE, and

SST25VF080B-80-4I-QAE

Jan 2010

05 •Updated “Auto Address Increment (AAI) Word-Program”, “End-of-Write

Detection”, and “Hardware End-of-Write Detection” on page 13.

•Revised Figures 10 and 11 on page page 15.

•Updated document to new format.

•Added SAE package drawing on page 33 and SAE information to “Prod-

uct Ordering Information” on page 30

Feb 2011

SST, Silicon Storage Technology, the SST logo, SuperFlash, MTP, and FlashFlex are registered trademarks of Silicon Storage Tech-

nology, Inc. MPF, SQI, Serial Quad I/O, and Z-Scale are trademarks of Silicon Storage Technology, Inc. All other trademarks and

registered trademarks mentioned herein are the property of their respective owners.

Specifications are subject to change without notice. Refer to www.microchip.com or www.sst.com for the most recent documentation.

Memory sizes denote raw storage capacity; actual usable capacity may be less.

SST makes no warranty for the use of its products other than those expressly contained in the Standard Terms and Conditions of

Sale.

For sales office(s) location and information, please see www.microchip.com or www.sst.com.

Silicon Storage Technology, Inc.

A Microchip Technology Company