CENTIGRID(R) SURFACE MOUNT COMMERCIAL RELAYS SERIES S172 DPDT SERIES DESIGNATION RELAY TYPE S172 DPDT basic relay S172D DPDT relay with internal diode for coil transient suppression INTERNAL CONSTRUCTION DESCRIPTION The S172 surface mount Centigrid(R) relay is an ultraminiature, hermetically UNI-FRAME sealed, armature relay for commercial applications. Its low profile height (.470) ARMATURE and .100" grid spaced terminals make it an ideal choice where extreme UPPER STATIONARY CONTACT packaging density and/or close PC board spacing are required. The specially MOVING CONTACT formed leads are pre-tinned to make the relays ideal for all types of surface- LOWER STATIONARY CONTACT mount solder reflow processes. The basic design and internal structure are similar to Teledyne's DPDT 114 CENTIGRID(R) AND TO-5 Centigrid(R) relay. Unique construction features and manufacturing techniques provide overall high reliability and excellent resistance to environmental extremes: * All welded construction. * Unique uni-frame design providing high magnetic efficiency and mechanical ENVIRONMENTAL AND PHYSICAL SPECIFICATIONS -65C to +125C Temperature Storage (Ambient) Operating -55C to +85C rigidity. * High force/mass ratios for resistance to shock and vibration. * Advanced cleaning techniques provide maximum assurance of internal cleanliness. Vibration (General Note 1) 10 g's to 500 Hz Shock (General Note 1) 30 g's, 6 msec, half-sine Enclosure Hermetically sealed Weight 0.15 oz. (4.3g) max. The S172D relay has an internal discrete silicon diode for coil transient Reflow Temperature 260C max. temp. 1 min. max. suppression. (c)2003 TELEDYNE RELAYS * Precious metal alloy contact material with gold plating assures excellent high current and dry circuit switching capabilities. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE www.teledynerelays.com S172 Page 1 S172/1203/Q1 SERIES S172 GENERAL ELECTRICAL SPECIFICATIONS (@25C) (Notes 2 & 3) Contact Arrangement Rated Duty Contact Resistance 2 Form C (DPDT) Continuous 0.15 ohm max. before life; 0.3 ohm max. after life at 1A/28Vdc (measured 1/8" from header) Contact Load Ratings (DC) (See Fig. 1 for other DC resistive voltage/current ratings) Resistive: Inductive: Lamp: Low Level: 1 Amp/28Vdc 200 mA/28Vdc (320 mH) 100 mA/28Vdc 10 to 50 A/10 to 50mV 5,000,000 cycles (typical) at low level 500,000 cycles (typical) at 0.5A/28Vdc resistive 100,000 cycles min. at all other loads specified above Contact Life Ratings Contact Overload Rating Contact Carry Rating Operate Time Release Time Contact Bounce Intercontact Capacitance Insulation Resistance Dielectric Strength Negative Coil Transient (Vdc) Diode P.I.V. (Vdc) 2A/28Vdc Resistive (100 cycles min.) Contact factory 6.0 msec max. at nominal rated coil voltage S172: 3.0 msec max. S172D: 6.0 msec max. 1.5 msec max. 0.4 pf typical 1,000 megohms min. between mutually isolated terminals Atmospheric pressure: 300 Vrms/60Hz S172D S172D 2.0 max 60 min. DETAILED ELECTRICAL SPECIFICATIONS (@25C) (Note 3) BASE PART NUMBERS Nom. Max. Coil Voltage (Vdc) Coil Resistance (Ohms 20%) Pick-up Voltage (Vdc, Max.) Pulse Operation Coil Operating Power at Nominal Voltage (Milliwatts) TYPICAL DC CONTACT RATINGS (RESISTIVE) LOAD VOLTAGE (VDC) 250 200 150 100 50 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 LOAD CURRENT (AMPS DC) FIGURE 1 0.8 0.9 1.0 S172-12 S172D-12 S172-26 S172D-26 5.0 5.8 64 3.8 405 12.0 16.0 400 9.0 360 26.5 32.0 1600 18.0 440 GENERAL NOTES 1. Relay contacts will exhibit no chatter in excess of 10 sec or transfer in excess of 1 sec. 2. "Typical" characteristics are based on available data and are best estimates. No on-going verification tests are performed. 3. Unless otherwise specified, parameters are initial values. 4. Position of leads as they emerge from relay base. 5. Leads will fit noted pad layout with no overhang. 6. Lead ends are coplanar within .008" wide tolerance zone. 7. Terminals coated with SN60 or SN63 solder per QQ-S571. Base material exposed at sheared end of leads. 8. Add "/R" to end of part number for RoHS compliant solder coated pins (Sn99.3/Cu0.7). CENTIGRID(R) AND TO-5 300 S172-5 S172D-5 Appendix A: Spacer Pads Pad designation and bottom view dimensions Height O.150 [3.81] (REF) Dim H MAX "M4" Pad for TO-5 Dim H MAX "M4" Pad for TO-5 Dim H MAX "M4" Pad for Centigrid(R) .156 [3.96] (REF) Dim H MAX .256 [6.5] (REF) "M9" Pad for Centigrid(R) For use with the following: ER411T ER412, ER412D, ER412DD 712, 712D, 712TN, RF300, RF310, RF320 ER420, ER422D, ER420DD, 421, ER421D, ER421DD, ER422, ER422D, ER422DD, 722, 722D, RF341 ER431T, ER432T, ER432, ER432D, ER432DD 732, 732D, 732TN, RF303, RF313, RF323 .295 (7.49) .300 (7.62) .305 (7.75) .400 (10.16) .410 (10.41) RF312 .350 (8.89) ER411, ER411D, ER411DD .295 (7.49) ER431, ER431D, ER431DD .400 (10.16) RF311 .300 (7.62) RF331 .410 (10.41) 172, 172D .305 (7.75) ER114, ER114D, ER114DD, J114, J114D, J114DD .300 (7.62) ER134, ER134D, ER134DD, J134, J134D, J134DD .400 (10.16) RF100 .315 (8.00) RF103 .420 (10.67) 122C, A152 .320 (8.13) ER116C, J116C .300 (7.62) ER136C, J136C .400 (10.16) RF180 .325 (8.25) A150 .305 (7.75) Notes: 1. Spacer pad material: Polyester lm. 2. To specify an "M4" or "M9" spacer pad, refer to the mounting variants portion of the part numbering example in the applicable datasheet. 3. Dimensions are in inches (mm). 4. Unless otherwise specied, tolerance is .010 (.25). 5. Add 10 m to the contact resistance show in the datasheet. 6. Add 0.01 oz. (0.25 g) to the weight of the relay assembly shown in the datasheet. (c) 2008 Teledyne Relays Dim. H Max. SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Appendix A: Spreader Pads Pad designation and bottom view dimensions Height For use with the following: .370 [9.4] MAX SQ .100 [2.54] Dim H MAX .150 [3.81] .014 [0.36] (REF) .300 [7.62] .100 [2.54] .370 [9.4] MIN .200 [5.08] "M" Pad 5/ 6/ .390 [9.91] SQ .100 [2.54] .100 [2.54] .150 [3.81] .300 [7.62] .300 [7.62] .150 [3.81] Dim H MAX ER411T, J411T, ER412, ER412D ER412DD, J412, J412D, J412DD ER412T, J412T 712, 712D, 712TN ER431T, J431T, ER432, ER432D ER432DD, J432, J432D, J432DD ER432T, J432T 732, 732D, 732TN .370 [9.4] MAX SQ .100 [2.54] Dim H MAX .150 [3.81] .014 [0.36] (REF) .300 [7.62] .100 [2.54] .200 [5.08] .370 [9.4] MIN "M3" Pad 5/ 6/ 9/ .393 (9.99) .493 (12.52) .503 (12.78) .398 (10.11) ER411T ER412, ER412D, ER412DD J412, J412D, J412DD .441 (11.20) 732, 732D "M2" Pad 7/ 8/ .388 (9.86) ER420, J420, ER420D, J420D ER420DD, J420DD, ER421, J421 ER421D, J421D, ER421DD J422D, ER422DD, J422DD, 722 712, 712D ER421, ER421D, ER421DD 722, 732D ER431T ER432, ER432D, ER432DD .130 [3.3] Dim. H Max. ER411, ER411D, ER411DD ER411TX ER412X, ER412DX, ER412DDX ER412TX 712X, 712DX, 712TNX ER420X, ER420DX, ER420DDX ER421X, ER421DX, ER421DDX ER422X, ER422DX ER422DDX, 722X, 722DDX ER431, ER431D, ER431DD ER431TX ER432X, ER432DX, ER432DDX ER432TX 732X, 732DX, 732TNX .451 (11.46) .451 (11.46) .546 (13.87) .556 (14.12) .388 (9.86) .393 (9.99) .398 (10.11) .493 (12.52) .503 (12.78) Notes: 1. Spreader pad material: Diallyl Phthalate. 2. To specify an "M", "M2" or "M3" spreader pad, refer to the mounting variants portion of the part number example in the applicable datasheet. 3. Dimensions are in inches (mm). 4. Unless otherwise specied, tolerance is .010" (0.25). 5/. Add 25 m to the contact resistance shown in the datasheet. 6/. Add .01 oz. (0.25 g) to the weight of the relay assembly shown in the datasheet. 7/. Add 50 m to the contact resistance shown in the datasheet. 8/. Add 0.025 oz (0.71 g) to the weight of the relay assembly shown in the datasheet. 9/. M3 pad to be used only when the relay has a center pin (e.g. ER411M3-12A, 722XM3-26.) (800) 284-7007 * www.teledynerelays.com +44 (0) 1236 453124 * www.teledyne-europe.com (c) 2008 Teledyne Relays Appendix A: Ground Pin Positions O.200 [O5.08] 363 "Z" POSITION "X" POSITION "Y" POSITION "Z" O.200 [O5.08] "Y" 453 TO-5 Relays: ER411T, ER412, ER412T, ER420, ER421, ER422, ER431T, ER432, ER432T, 712, 712TN, 400H, 400K, 400V, RF300, RF303, RF341, RF312, RF310, RF313, RF320, RF323 "Y" POSITION POSITION TO-5 Relays: ER411, ER431, RF311, RF331 POSITION .100 [2.54] "W" "Z" .100 [2.54] .050 [1.27] "X" .100 [2.54] POSITION POSITION "Z" POSITION POSITION .100 [2.54] POSITION "U" POSITION (ER116C and ER136C only) Centigrid(R) Relays: RF180, ER116C, 122C, ER136C .100 [2.54] Centigrid(R) Relays: RF100, RF103, ER114, ER134, 172 Indicates ground pin position Indicates glass insulated lead position Indicates ground pin or lead position depending on relay type (c) 2008 Teledyne Relays "Y" .100 [2.54] NOTES 1. Terminal views shown 2. Dimensions are in inches (mm) 3. Tolerances: .010 (.25) unless otherwise specied 4. Ground pin positions are within .015 (0.38) dia. of true position 5. Ground pin head dia., 0.035 (0.89) ref: height 0.010 (0.25) ref. 6. Lead dia. 0.017 (0.43) nom. SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE