TPS61097 SLVS872C - JUNE 2009 - REVISED DECEMBER 2011 www.ti.com LOW INPUT VOLTAGE SYNCHRONOUS BOOST CONVERTER WITH LOW QUIESCENT CURRENT Check for Samples: TPS61097 FEATURES 1 * * * * * * * * APPLICATIONS Up to 95% Efficiency at Typical Operating Conditions Connection from Battery to Load via Bypass Switch in Shutdown Mode Typical Shutdown Current Less Than 5 nA Typical Quiescent Current Less Than 5 A Operating Input Voltage Range From 0.9 V to 5.5 V Power-Save Mode for Improved Efficiency at Low Output Power Overtemperature Protection Small 2.8-mm x 2.9-mm 5-Pin SOT-23 Package (6-Pin for Adjustable) * * * * * * * MSP430 Applications All Single-Cell, Two-Cell, and Three-Cell Alkaline, NiCd, NiMH, or Single-Cell Li-Battery Powered Products Personal Medical Products Fuel Cell and Solar Cell Powered Products PDAs Mobile Applications White LEDs DESCRIPTION The TPS61097 provide a power supply solution for products powered by either a single-cell, two-cell, or three-cell alkaline, NiCd, or NiMH, or one-cell Li-Ion or Li-polymer battery. They can also be used in fuel cell or solar cell powered devices where the capability of handling low input voltages is essential. Possible output currents depend on the input-to-output voltage ratio. The devices provides output currents up to 100 mA at a 3.3-V output while using a single-cell Li-Ion or Li-Polymer battery. The boost converter is based on a current-mode controller using synchronous rectification to obtain maximum efficiency. The maximum average input current is limited to a value of 350 mA. The output voltage can be programmed by an external resistor divider, or it is fixed internally on the chip. The converter can be disabled to minimize battery drain. During shutdown, the battery is connected to the load to enable battery backup of critical functions on the load. The fixed output device is packaged in a 5-pin SOT-23 package (DBV) measuring 2.8 mm x 2.9 mm. L1 L TPS61097-33 VOUT VOUT +3.3V C2 VIN 0.9 V to 3.3V VIN C1 EN GND 1 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. UNLESS OTHERWISE NOTED this document contains PRODUCTION DATA information current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2009-2011, Texas Instruments Incorporated TPS61097 SLVS872C - JUNE 2009 - REVISED DECEMBER 2011 www.ti.com ORDERING INFORMATION PACKAGE (3) TA -40C to 85C (1) 5-pin SOT-23 - DBV (1) (2) ORDERABLE PART NUMBER Reel of 3000 TPS61097-33DBVR Reel of 250 TPS61097-33DBVT TOP-SIDE MARKING NFSK For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI web site at www.ti.com. Contact the factory for availability of other fixed output voltage versions. Package drawings, thermal data, and symbolization are available at www.ti.com/packaging. (2) (3) ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range (unless otherwise noted) (1) VI Input voltage range Isc Short-circuit current TJ Junction temperature range Tstg Storage temperature range ESD (1) (2) -0.3 V to 7 V VIN, L, VOUT, EN, FB 400 mA Electrostatic discharge rating -40C to 150C -65C to 150C Human-Body Model (HBM) (2) 2000 V Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. ESD testing is performed according to the respective JESD22 JEDEC standard. DISSIPATION RATINGS TABLE PACKAGE THERMAL RESISTANCE JA POWER RATING TA 25C DERATING FACTOR ABOVE TA = 25C DBV 255C/W 390 mW -3.92 mW/C RECOMMENDED OPERATING CONDITIONS MIN MAX 0.9 5.5 Adjustable output voltage 1.8 5.5 V Operating free air temperature range -40 85 C Operating junction temperature range -40 125 C VIN Supply voltage at VIN VOUT TA TJ 2 Submit Documentation Feedback UNIT V Copyright (c) 2009-2011, Texas Instruments Incorporated TPS61097 SLVS872C - JUNE 2009 - REVISED DECEMBER 2011 www.ti.com ELECTRICAL CHARACTERISTICS over recommended free-air temperature range and over recommended input voltage range (typical at an ambient temperature range of 25C) (unless otherwise noted) DC/DC STAGE PARAMETER TEST CONDITIONS MIN TYP MAX 0.9 VIN Input voltage VOUT TPS61097-33 VIN = 1.2 V , IOUT = 10 mA 3.20 3.30 3.40 V ISW Switch current limit VOUT = 3.3 V 200 350 475 mA Rectifying switch on resistance VOUT = 3.3 V 1.0 Main switch on resistance VOUT = 3.3 V 1.0 Bypass switch on resistance VIN = 1.2 IOUT = 100 mA 3.4 Line regulation VIN < VOUT, VIN = 1.2 V to 1.8 V, IOUT = 10 mA 0.5% VIN < VOUT, IOUT = 10 mA to 50 mA, VIN = 1.8 V 0.5% Load regulation IQ Quiescent current ISD Shutdown current VIN VOUT VIN Leakage current into L 5.5 UNIT V 1 2.5 A 4 6.5 A VEN = 0 V, VIN = 1.2 V, IOUT = 0 mA 0.005 0.15 VEN = 0 V, VIN = 3 V, IOUT = 0 mA 0.005 0.15 VEN = 0 V, VIN = 1.2 V, VL = 1.2 V 0.01 1 TYP MAX 0.01 0.1 A 0.65 V VIN + 1.0 V V IO = 0 mA, VEN = VIN = 1.2 V, VOUT = 3.4V A A CONTROL STAGE PARAMETER EN input current VIL Logic low level, EN falling edge VIH Logic high level, EN rising edge TEST CONDITIONS 0.78 Overtemperature protection Undervoltage lock-out threshold for turn off Copyright (c) 2009-2011, Texas Instruments Incorporated C 20 VIN decreasing 0.5 UNIT C 150 Overtemperature hysteresis VUVLO MIN EN = 0 V or EN = VIN 0.7 Submit Documentation Feedback 3 TPS61097 SLVS872C - JUNE 2009 - REVISED DECEMBER 2011 www.ti.com PIN ASSIGNMENTS FIXED OUTPUT VOLTAGE DBV PACKAGE (TOP VIEW) VIN 1 GND 2 EN 3 5 L 4 VOUT Terminal Functions TERMINAL NAME 4 NO. I/O DESCRIPTION Fixed VIN 1 I Boost converter input voltage GND 2 EN 3 I Enable input (1 = enabled, 0 = disabled). EN must be actively terminated high or low. VOUT 4 O Boost converter output L 5 I Connection for inductor FB - I Voltage feedback Control / logic ground Submit Documentation Feedback Copyright (c) 2009-2011, Texas Instruments Incorporated TPS61097 SLVS872C - JUNE 2009 - REVISED DECEMBER 2011 www.ti.com FUNCTIONAL BLOCK DIAGRAM (FIXED OUTPUT VERSION) Bypass Switch P N L VOUT Rectifying Switch Thermal Shutdown Startup Circuit N Driver VIN Undervoltage Lockout Bypass Switch Control Main Switch Control Logic Current Sense EN Overvoltage Protection GND 1.20 V Copyright (c) 2009-2011, Texas Instruments Incorporated Submit Documentation Feedback 5 TPS61097 SLVS872C - JUNE 2009 - REVISED DECEMBER 2011 www.ti.com PARAMETER MEASUREMENT INFORMATION L L1 TPS61097-33 VOUT VOUT +3.3V C2 VIN 0.9 V to 3.3V VIN C1 EN GND C1 10 F C2 10 F L 10 H Table 1. List of Components 6 REFERENCE MANUFACTURER PART NO. C1 Murata GRM319R61A106KE19 10F 10V X5R 1206 20% C2 Murata GRM319R61A106KE19 10F 10V X5R 1206 20% L1 Coilcraft DO3314-103MLC Submit Documentation Feedback Copyright (c) 2009-2011, Texas Instruments Incorporated TPS61097 SLVS872C - JUNE 2009 - REVISED DECEMBER 2011 www.ti.com TYPICAL CHARACTERISTICS Table 2. Table of Graphs FIGURE Maximum Output Current Efficiency Input Current Startup Voltage Output Voltage Waveforms vs Input Voltage 1 vs Output Current 2 vs Input Voltage 3 vs Input Voltage (Device Enabled, No Output Load, VOUT = 3.3 V) 4 vs Input Voltage (Device Disabled, No Output Load) 5 vs Temperature 6 vs Output Current 7 vs Output Current 8 vs Input Voltage 9 Output Voltage Ripple 10 Load Transient Response 11 Line Transient Response 12 Switching Waveform, Continuous Mode 13 Switching Waveform, Discontinuous Mode 14 Startup After Enable (VIN = 1.2 V, IOUT = 10 mA) 15 Startup After Enable (VIN = 1.8 V, IOUT = 10 mA) 16 MAXIMUM OUTPUT CURRENT vs INPUT VOLTAGE EFFICIENCY vs OUTPUT CURRENT 0.25 100 90 80 0.20 70 Efficiency - % IO(max) - Maximum Output Current - A COUT = 10 F, ceramic L = 10 H 0.15 0.10 VIN = 3 V 60 VIN = 2.5 V 50 VIN = 1.8 V 40 VIN = 1.5 V 30 VIN = 1.2 V 20 0.05 COUT = 10 F, ceramic L = 10 H 10 VIN = 0.9 V 0 0.00 0.9 1.2 1.5 1.8 2.1 2.4 VI - Input Voltage - V Figure 1. Copyright (c) 2009-2011, Texas Instruments Incorporated 2.7 3 0.1 1 10 100 IO - Output Current - mA Figure 2. Submit Documentation Feedback 7 TPS61097 SLVS872C - JUNE 2009 - REVISED DECEMBER 2011 www.ti.com EFFICIENCY vs INPUT VOLTAGE INPUT CURRENT vs INPUT VOLTAGE 100 20 IOUT = 10 mA 90 18 80 16 IIN - Input Current - A Efficiency - % 70 IOUT = 100 A 60 IOUT = 5 mA IOUT = 100 mA 50 IOUT = 50 mA 40 30 20 Device Enabled No Output Load VOUT = 3.3 V 14 12 10 8 6 4 COUT = 10 F, ceramic L = 10 H 10 2 0 0 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3.0 0.9 1.2 1.5 1.8 2.1 2.4 VIN - Input Voltage - V Figure 4. INPUT CURRENT vs INPUT VOLTAGE STARTUP VOLTAGE vs TEMPERATURE 3.3 3.6 3.9 4.2 0.720 VIN = 1.8 V No Load Device Disabled No Output Load 0.718 100 0.716 80 Startup Voltage - V IIN - Input Current - nA 3 Figure 3. 120 60 40 0.714 0.712 0.710 20 0.708 0 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3 3.3 3.6 3.9 4.2 VIN - Input Voltage - V Figure 5. 8 2.7 VIN - Input Voltage - V Submit Documentation Feedback 0.706 -40 -25 -10 5 20 35 50 65 80 TA - Temperature - C Figure 6. Copyright (c) 2009-2011, Texas Instruments Incorporated TPS61097 SLVS872C - JUNE 2009 - REVISED DECEMBER 2011 www.ti.com STARTUP VOLTAGE vs OUTPUT CURRENT OUTPUT VOLTAGE vs OUTPUT CURRENT 0.725 3.32 COUT = 10 F, ceramic L = 10 H VIN = 1.8 V 3.30 VOUT - Output Voltage - V Startup Voltage - V 0.720 0.715 0.710 VIN = 0.9 V VIN = 1.2 V 3.26 VIN = 1.5 V VIN = 1.8 V 3.24 0.700 3.20 10 VIN = 3.0 V 3.28 3.22 1 VIN = 2.5 V VIN = 2.7 V 0.705 0 1 100 VIN = 2.1 V 10 100 IOUT - Output Current - mA 1000 IOUT - Output Current - mA Figure 7. Figure 8. OUTPUT VOLTAGE vs INPUT VOLTAGE 6 Device disabled VOUT - Ouput Voltage - V 5 4 RLOAD = 1k 3 RLOAD = 122 2 1 0 0 1 2 3 4 5 6 VIN - Input Voltage - V Figure 9. Copyright (c) 2009-2011, Texas Instruments Incorporated Submit Documentation Feedback 9 TPS61097 SLVS872C - JUNE 2009 - REVISED DECEMBER 2011 www.ti.com OUTPUT VOLTAGE RIPPLE Inductor Current VIN = 1.8 V IOUT = 50 mA COUT = 10 F, ceramic L = 10 H VOUT Figure 10. LOAD TRANSIENT RESPONSE IOUT VIN = 1.2 V IOUT = 6 mA to 50 mA VOUT Figure 11. 10 Submit Documentation Feedback Copyright (c) 2009-2011, Texas Instruments Incorporated TPS61097 SLVS872C - JUNE 2009 - REVISED DECEMBER 2011 www.ti.com LINE TRANSIENT RESPONSE VIN Offset 1.8 V VIN = 1.8 V to 2.4 V RLOAD = 100 W VOUT Figure 12. SWITCHING WAVEFORM, CONTINUOUS MODE VIN = 1.8 V IOUT = 50 mA Inductor Current Inductor Voltage VOUT Figure 13. Copyright (c) 2009-2011, Texas Instruments Incorporated Submit Documentation Feedback 11 TPS61097 SLVS872C - JUNE 2009 - REVISED DECEMBER 2011 www.ti.com SWITCHING WAVEFORM, DISCONTINUOUS MODE VIN = 1.8 V IOUT = 10 mA Inductor Current Inductor Voltage VOUT Figure 14. STARTUP AFTER ENABLE VIN = 1.2 V IOUT = 10 mA VOUT VEN Figure 15. 12 Submit Documentation Feedback Copyright (c) 2009-2011, Texas Instruments Incorporated TPS61097 SLVS872C - JUNE 2009 - REVISED DECEMBER 2011 www.ti.com STARTUP AFTER ENABLE VIN = 1.8 V IOUT = 10 mA VOUT VEN Figure 16. Copyright (c) 2009-2011, Texas Instruments Incorporated Submit Documentation Feedback 13 TPS61097 SLVS872C - JUNE 2009 - REVISED DECEMBER 2011 www.ti.com DETAILED DESCRIPTION Operation The TPS61097 is a high performance, high efficient family of switching boost converters. To achieve high efficiency the power stage is realized as a synchronous boost topology. For the power switching two actively controlled low RDSon power MOSFETs are implemented. Controller Circuit The device is controlled by a hysteretic current mode controller. This controller regulates the output voltage by keeping the inductor ripple current constant in the range of 200 mA and adjusting the offset of this inductor current depending on the output load. If the required average input current is lower than the average inductor current defined by this constant ripple the inductor current goes discontinuous to keep the efficiency high at low load conditions. IL Continuous Current Operation Discontinuous Current Operation 200 mA (typ.) 200 mA (typ.) t Figure 17. Hysteretic Current Operation The output voltage VOUT is monitored via the feedback network which is connected to the voltage error amplifier. To regulate the output voltage, the voltage error amplifier compares this feedback voltage to the internal voltage reference and adjusts the required offset of the inductor current accordingly. For fixed output voltage versions, the feedback function is connected internally. A resistive divider network is required to set the output voltage with the adjustable option. The self oscillating hysteretic current mode architecture is inherently stable and allows fast response to load variations. It also allows using inductors and capacitors over a wide value range. Device Enable and Shutdown Mode The device is enabled when EN is set high and shut down when EN is low. During shutdown, the converter stops switching and all internal control circuitry is turned off. Bypass Switch The TPS61097 contains a P-channel MOSFET (Bypass Switch) in parallel with the synchronous rectifying MOSFET. When the IC is enabled (EN = VIH), the Bypass Switch is turned off to allow the IC to work as a standard boost converter. When the IC is disabled (EN = VIL) the Bypass Switch is turned on to provide a direct, low impedance connection from the input voltage (at the L pin) to the load (VOUT). The Bypass Switch is not impacted by Undervoltage lockout, Overvoltage or Thermal shutdown. Startup After the EN pin is tied high, the device starts to operate. If the input voltage is not high enough to supply the control circuit properly a startup oscillator starts to operate the switches. During this phase the switching frequency is controlled by the oscillator and the maximum switch current is limited. As soon as the device has built up the output voltage to about 1.8 V, high enough for supplying the control circuit, the device switches to its normal hysteretic current mode operation. The startup time depends on input voltage and load current. Operation at Output Overload If in normal boost operation the inductor current reaches the internal switch current limit threshold the main switch is turned off to stop further increase of the input current. In this case the output voltage will decrease since the device can not provide sufficient power to maintain the set output voltage. 14 Submit Documentation Feedback Copyright (c) 2009-2011, Texas Instruments Incorporated TPS61097 www.ti.com SLVS872C - JUNE 2009 - REVISED DECEMBER 2011 If the output voltage drops below the input voltage the backgate diode of the rectifying switch gets forward biased and current starts flow through it. Because this diode cannot be turned off, the load current is only limited by the remaining DC resistances. As soon as the overload condition is removed, the converter automatically resumes normal operation and enters the appropriate soft start mode depending on the operating conditions. Undervoltage Lockout An undervoltage lockout function stops the operation of the converter if the input voltage drops below the typical undervoltage lockout threshold. This function is implemented in order to prevent malfunctioning of the converter. The undervoltage lockout function has no control of the Bypass Switch. If the Bypass Switch is enabled (EN = VIL) there is no impact during an undervoltage condition, the Bypass Switch remains on. Overtemperature Protection The device has a built-in temperature sensor which monitors the internal IC temperature. If the temperature exceeds the programmed threshold (150 C typical), the device stops operating. As soon as the IC temperature has decreased below the programmed threshold, it starts operating again. There is a built-in hysteresis to avoid unstable operation at IC temperatures at the overtemperature threshold. Copyright (c) 2009-2011, Texas Instruments Incorporated Submit Documentation Feedback 15 TPS61097 SLVS872C - JUNE 2009 - REVISED DECEMBER 2011 www.ti.com APPLICATION INFORMATION Design Procedure The TPS61097 DC/DC converters are intended for systems powered by a single up to triple cell Alkaline, NiCd, NiMH battery with a typical terminal voltage between 0.9 V and 5.5 V. They can also be used in systems powered by one-cell Li-Ion or Li-Polymer with a typical voltage between 2.5 V and 4.2 V. Additionally, any other voltage source like solar cells or fuel cells with a typical output voltage between 0.9 V and 5.5 V can power systems where the TPS61097 is used. The TPS61097 does not down-regulate VIN; therefore, if VIN is greater than VOUT, VOUT tracks VIN. Adjustable Bypass Switching The EN pin can be set up as a low voltage control for the bypass switch. By setting the desired ratio of R1 and R2, the TPS61097 can be set to switch on the bypass at a defined voltage level on VIN. For example, setting R1 and R2 to 200K would set VEN to half of VIN. The voltage level of VIN engaging the bypass switch is based on the VIL level of EN (0.65 V). If VIN is less than 1.30 V then the bypass switch will be enabled. For VIN values above 1.50 V (50% of VIH) the bypass switch is disabled. TPS61097-33 L1 L VOUT +3.3V VOUT C2 VIN 0.9 V to 3.3V VIN C1 R1 EN R2 GND Figure 18. Adjustable Bypass Switching Inductor Selection To make sure that the TPS61097 devices can operate, a suitable inductor must be connected between pin VIN and pin L. Inductor values of 4.7 H show good performance over the whole input and output voltage range . Choosing other inductance values affects the switching frequency f proportional to 1/L as shown in Equation 1. L= V (VOUT - VIN ) 1 IN f 200 mA VOUT (1) Choosing inductor values higher than 4.7 H can improve efficiency due to reduced switching frequency and therefore with reduced switching losses. Using inductor values below 2.2 H is not recommended. Having selected an inductance value, the peak current for the inductor in steady state operation can be calculated. Equation 2 gives the peak current estimate. i VOUT IOUT + 100 mA; continous current operation i IL,MAX = i 0.8 VIN i200 mA; discontinuous current operation i (2) IL,MAX is the inductor's required minimum current rating. Note that load transient or over current conditions may require an even higher current rating. 16 Submit Documentation Feedback Copyright (c) 2009-2011, Texas Instruments Incorporated TPS61097 SLVS872C - JUNE 2009 - REVISED DECEMBER 2011 www.ti.com Equation 3 provides an easy way to estimate whether the device is operating in continuous or discontinuous operation. As long as the equation is true, continuous operation is typically established. If the equation becomes false, discontinuous operation is typically established. VOUT IOUT > 0.8 100 mA VIN (3) Due to the use of current hysteretic control in the TPS61097, the series resistance of the inductor can impact the operation of the main switch. There is a simple calculation that can ensure proper operation of the TPS61097 boost converter. The relationship between the series resistance (RIN), the input voltage (VIN) and the switch current limit (ISW) is shown in Equation 4. RIN < VIN / ISW (4) (4) Examples: ISW = 400 mA, VIN = 2.5 V (5) (5) In Equation 5, RIN < 2.5 V / 400 mA; therefore, RIN must be less than 6.25 . ISW = 400 mA, VIN = 1.8 V (6) (6) In Equation 6, RIN < 1.8 V / 400 mA; therefore, RIN must be less than 4.5 . The following inductor series from different suppliers have been used with TPS61097 converters: Table 3. List of Inductors VENDOR INDUCTOR SERIES Coilcraft DO3314 TDK NLC565050T Taiyo Yuden CBC2012T Capacitor Selection Input Capacitor The input capacitor should be at least 10-F to improve transient behavior of the regulator and EMI behavior of the total power supply circuit. The input capacitor should be a ceramic capacitor and be placed as close as possible to the VIN and GND pins of the IC. Output Capacitor For the output capacitor C2 , it is recommended to use small ceramic capacitors placed as close as possible to the VOUT and GND pins of the IC. If, for any reason, the application requires the use of large capacitors which can not be placed close to the IC, the use of a small ceramic capacitor with an capacitance value of around 2.2F in parallel to the large one is recommended. This small capacitor should be placed as close as possible to the VOUT and GND pins of the IC. A minimum capacitance value of 4.7 F should be used, 10 F are recommended. If the inductor value exceeds 4.7 H, the value of the output capacitance value needs to be half the inductance value or higher for stability reasons, see Equation 7. C2 L 2 (7) The TPS61097 is not sensitive to the ESR in terms of stability. Using low ESR capacitors, such as ceramic capacitors, is recommended to minimize output voltage ripple. If heavy load changes are expected, the output capacitor value should be increased to avoid output voltage drops during fast load transients. Copyright (c) 2009-2011, Texas Instruments Incorporated Submit Documentation Feedback 17 TPS61097 SLVS872C - JUNE 2009 - REVISED DECEMBER 2011 www.ti.com Table 4. Recommended Output Capacitors 18 VENDOR CAPACITOR SERIES Murata GRM188R60J106M47D 10F 6.3V X5R 0603 Murata GRM319R61A106KE19 10F 10V X5R 1206 Submit Documentation Feedback Copyright (c) 2009-2011, Texas Instruments Incorporated TPS61097 SLVS872C - JUNE 2009 - REVISED DECEMBER 2011 www.ti.com Layout Considerations As for all switching power supplies, the layout is an important step in the design, especially at high peak currents and high switching frequencies. If the layout is not carefully done, the regulator could show stability problems as well as EMI problems. Therefore, use wide and short traces for the main current path and for the power ground tracks. The input and output capacitor, as well as the inductor should be placed as close as possible to the IC. Use a common ground node for power ground and a different one for control ground to minimize the effects of ground noise. Connect these ground nodes at any place close to one of the ground pins of the IC. The feedback divider should be placed as close as possible to the control ground pin of the IC. To lay out the control ground, it is recommended to use short traces as well, separated from the power ground traces. This avoids ground shift problems, which can occur due to superimposition of power ground current and control ground current. Figure 19. Layout Schematic Copyright (c) 2009-2011, Texas Instruments Incorporated Submit Documentation Feedback 19 TPS61097 SLVS872C - JUNE 2009 - REVISED DECEMBER 2011 www.ti.com Figure 20. PCB Top View Thermal Information Implementation of integrated circuits in low-profile and fine-pitch surface-mount packages typically requires special attention to power dissipation. Many system-dependent issues such as thermal coupling, airflow, added heat sinks and convection surfaces, and the presence of other heat-generating components affect the power-dissipation limits of a given component. Three basic approaches for enhancing thermal performance are listed below. * Improving the power dissipation capability of the PCB design * Improving the thermal coupling of the component to the PCB * Introducing airflow in the system The maximum recommended junction temperature (TJ) of the TPS61097 devices is 125C. Specified regulator operation is assured to a maximum ambient temperature TA of 85C. Therefore, the maximum power dissipation is about TBD mW. More power can be dissipated if the maximum ambient temperature of the application is lower. 20 Submit Documentation Feedback Copyright (c) 2009-2011, Texas Instruments Incorporated TPS61097 SLVS872C - JUNE 2009 - REVISED DECEMBER 2011 www.ti.com REVISION HISTORY Changes from Revision B (December 2009) to Revision C Page * Deleted Fixed Output Voltage Options from 1.8V to 5.0V .................................................................................................... 1 * Deleted adjustable output feature from DESCRIPTION. ...................................................................................................... 1 * Deleted adjustable output feature listed in the ORDERING INFORMATION table. ............................................................. 2 * Deleted VOUT parameters for the TPS61097-18, TPS61097-27, TPS61097-30, and TPS61097-50 from the ELECTRICAL CHARACTERISTICS table. ........................................................................................................................... 3 * Deleted Overvoltage protection threshold parameter. .......................................................................................................... 3 * Deleted the adjustable output voltage pinout package. ........................................................................................................ 4 * Deleted the adjustable output voltage features from the Terminal Functions table. ............................................................ 4 * Deleted the Functional Block Diagram for the adjustable output version. ............................................................................ 5 * Deleted "Overvoltage Protection" and "Programming the Output Voltage" sections. ......................................................... 16 Copyright (c) 2009-2011, Texas Instruments Incorporated Submit Documentation Feedback 21 PACKAGE OPTION ADDENDUM www.ti.com 12-May-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp TPS61097-33DBVR ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS61097-33DBVT ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM (3) Samples (Requires Login) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 8-Jun-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device TPS61097-33DBVR Package Package Pins Type Drawing SPQ SOT-23 3000 DBV 5 Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 180.0 8.4 Pack Materials-Page 1 3.2 B0 (mm) K0 (mm) P1 (mm) 3.2 1.4 4.0 W Pin1 (mm) Quadrant 8.0 Q3 PACKAGE MATERIALS INFORMATION www.ti.com 8-Jun-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TPS61097-33DBVR SOT-23 DBV 5 3000 202.0 201.0 28.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated