Product Data Sheet OSC Series Ultra Miniature TCXO s Features Low Cost 3.0 or 5.0 Vdc Option Reflow Solderable <2.2 mm Height Voltage Tune Option Applications Wireless handsets, PCS, GSM, Cellular PCMCIA Applications GPS Description Vectron International has introduced a series of low-profile, low cost, surface mount, Temperature Compensated Crystal Oscillators (TCXOs) available in frequencies from 10 MHz to 25 MHz. The OSC series low-profile (0.09 inch maximum height), surface mount TCXOs can be mounted using the standard convection reflow process. The units feature a PPM frequency vs. temperature characteristic over a to operating range and operate from a 3.0V or 5V supply. Current drain <2.0 mA. Aging <1ppm/year and phase noise is -125 dBc/Hz at 100 Hz and -150 dbc/Hz at 100 kHz. The OSC series of TCXOs and TCVCXOs has been designed for pick-and-place mounting and reflow soldering. Units are available on tape-and-reel at no additional charge. The reel size is 2000 pcs. and is compatible with EIAJ-1009B standards. The low-cost, miniature units are ideal for wireless handsets, PCMCIA applications, and GPS receivers. OSC Series Ultra Miniature TCXO s Performance Characteristics Parameter Characteristics Option A = +5 Vdc Frequency range: 10 MHz to 25 MHz Stability Options: (relative to 1 2 3 4 Stability vs. Supply Aging (typical): Input Voltage: = = = = ppm ppm ppm ppm +5.0 Vdc <1.5 mA (10.0 to 16.8 MHz). <2.0 mA (16.8 to 20.0 MHz). +5.0 Vdc = 1.0 VP-P minimum PPM min. Trim options: 0 = Mechanical trim, no VCO 1= ppm VC & mechanical 2 = Voltage trim only ppm min. Voltage Control Input Impedence: Frequency Tolerance at +3.0 Vdc = 0.7 VP-P minimum 10 K /10pf Mechanical trim: Control Voltage Range: to to to to +3.0 Vdc Load: Supply Voltage: -20 -30 -30 -40 ppm vs B+ of < 1.0 ppm/year at Current: Output: Clipped Sinewave Option B= +3 Vdc 100K minimum +5.0 Vdc +3.0 Vdc +0.5Vdc to +4.5Vdc +0.5Vdc to +2.5Vdc ppm at +2.5 Vdc ppm at +1.5 Vdc Start-up time: <10 mS (typical) to within Harmonics: 2nd harmonic 3rd harmonic Other > 3 dBc down > 6 dBc down > 10 dBc down Phase Noise (typical): at 10 MHz PPM -80 dBc/Hz max. at 10 Hz offset -125 dBc/Hz max. at 100 Hz offset -145 dBc/Hz max. at 1 KHz offset -148 dBc/Hz max. at 10 KHz offset -150 dBc/Hz max. at 100 KHz offset Vectron International 166 Glover Avenue, Norwalk, CT 06856 Tel: 1-88-VECTRON-1 Fax: 1-888-FAX-VECTRON 2 OSC Series Ultra Miniature TCXO s 0.39 (9.9) max 3 2 4 1 The OSC series of TCXO s and VCTCXO s has been designed for pick and place and reflow soldering. Units are available on Tape and Reel at no additional charge when ordering a complete reel. The reel size is 2000 pcs and is compatible with EIAJ-1009B standards. The suggested reflow profile is shown below. The TCXO may be reflowed two times. Frequency shift as a result of reflow will be <1.0PPM. Units should not be adjusted to center frequencies until at least 2 hours after reflow to allow the crystals to stabilize. 0.47 (11.8) max Frequency adjust access Terminal #1 identifier The OSC footprint is compatible with many of the previous generation 6 pin leaded TCXO s. Our OSE model is the same size as the OSC except it provides the two additional pads to match pad connections of 6 pin leaded TCXO s and VCTCXO s. 0.09 (2.2) max 0.055 (1.4) 2 places 0.020 (0.5) 0.050 (1.3) 4 places 4 1 0.025 (0.7) 4 places TCXO s are precision subsystems with tolerances measured to Non-hermetically sealed TCXO s should not be subjected to a wash process that will immerse the TCXO in solvents. No clean is the recommended procedure. 0.300 (7.62) 0.040 (1.2) 4 places 3 2 Model OSC Land Pattern PIN 1 = VC or N/C PIN 2 = GROUND PIN 3 = OUTPUT PIN 4 = B+ Convection Reflow Profile 1.4mm 7.62mm 1.4mm 8.4mm 1.9mm 1.9mm warm-up >30 sec. pre-heating 50 to 90 sec at reflow 20 to 40 soc Vectron International 166 Glover Avenue, Norwalk, CT 06856 Tel: 1-88-VECTRON-1 Fax: 1-888-FAX-VECTRON 3 OSC Series Ultra Miniature TCXO s Order Information Standard Frequencies* (MHz) 10.0 12.8 13.0 14.4 15.56 16.0 19.2 19.98 20.0 25.0 How To Order at OSC- Frequency Stability Code (from page 2) Trim Option 0 = Mechanical trim, no VCO 1= ppm VC & mechanical 2 = Voltage trim only ppm min. Input Voltage A = +5.0 Vdc <2.0 mA MAX. B = +3.0 Vdc <1.5 mA (10.0 to 16.8 MHz) <2.0 mA (16.8 to 20.0 MHz) Example of typical P/N OSC-3B2 19.2 MHz 3= ppm B = +3.0 Vdc 2 = Voltage Tune no mechanical trimmer Visit Our Website at www.vectron.com For additional information please contact: www.vectron.com Vectron International reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. 4 Printed in USA 2/99