P6KE Series Features: * * * * * * * * Plastic package. Exceeds environmental standards of MIL-STD-19500. 600W surge capability at 10 x 1000s waveform, duty cycle: 0.01%. Excellent clamping capability. Low zener impedance. Fast response time: typically less than 1.0ps from 0 volts to VBR for unidirectional and 5.0ns for bidirectional. Typical IR less than 1A above 10V. High temperature soldering guaranteed: 260C/10 seconds/0.375 Inch (9.5mm) lead length/5lbs. (2.3kg) tension. DO-15 Dimensions : Inches (Millimetres) Mechanical Data Case Lead Polarity Weight : : : : Molded plastic Pure tin plated lead free, solderable per MIL-STD-202, Method 208. Color band denotes cathode except bipolar. 0.42 gram. Maximum Ratings and Electrical Characteristics Rating at 25C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. Page <1> 19/05/08 V1.1 P6KE Series Type Number Symbol Value Peak Power Dissipation at TA = 25C, Tp = 1ms (Note 1) PPK Minimum 600 Steady State Power Dissipation at TL = 75C Lead Lengths 0.375 Inch 9.5mm (Note 2) PD 5.0 IFSM 100 Amps VF 3.5/5.0 Volts TJ, TSTG -55 to + 175 C Peak Forward Surge Current, 8.3ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method) (Note 3) Maximum Instantaneous Forward Voltage at 50.0A for Unidirectional Only (Note 4) Operating and Storage Temperature Range Units Watts Notes: 1. Non-repetitive current pulse and derated above TA = 25C. 2. Mounted on copper pad area of 1.6 x 1.6 inch (40 x 40mm) per. 3. 8.3ms single half sine-wave or equivalent square wave, duty cycle = 4 pulses per minutes maximum. 4. VF = 3.5V for devices of VBR 200V and VF = 5.0V maximum for devices of VBR>200V. Devices for bipolar applications 1. For bidirectional use C or CA suffix for types P6KE6.8 through types P6KE400. 2. Electrical characteristics apply in both directions. Ratings and Characteristic Curves PPPM, Peak Pulse Power, KW Peak Pulse Power Rating Curve tp, Pulse Width, sec. Peak Pulse Power (PPP) or Current (IPPM) Derating In Percentage, % Pulse Derating Curve TA Ambient Temperature, C Page <2> 19/05/08 V1.1 P6KE Series Peak Pulse Current - % Clamping Power Pulse Waveform t, Time, ms Typical Junction Capacitance (Unidirectional) CJ, Junction Capacitance (pF) IFSM, Peak Forward Surge Current, Amperes Maximum Non-Repetitive Forward Surge Current Unidirectional Only Number of Cycles at 60Hz V Page <3> (BR), Breakdown Voltage Volts 19/05/08 V1.1 P6KE Series Electrical Characteristics (TA = 25C unless otherwise noted) Breakdown Voltage Device Unidirectional Bidirectional Maximum Maximum Maximum Test Stand-Off Reverse Peak Clamping Maximum Nominal VBR (Volts) (Note 1) Current Voltage Pulse Leakage Voltage Temperature Voltage at IT VWM Current I Coefficient RSM at VWM at IPPM (Volts) of VBR(%/C) (mA) (Volts) (Note 2) A) ID ( VC (Volts) Minimum Maximum (Amps) P6KE100A P6KE100CA 100.0 95.0 105.0 85.5 5.0 4.5 137.0 0.106 P6KE10A P6KE10CA 10.0 9.50 10.5 8.55 10.0 43.0 14.5 0.073 P6KE110A P6KE110CA 110.0 105.0 116.0 94.0 4.1 152.0 P6KE120A P6KE120CA 120.0 114.0 126.0 102.0 3.8 165.0 P6KE12A P6KE12CA 12.0 11.4 12.6 10.2 37.0 16.7 0.078 P6KE13A P6KE13CA 13.0 12.4 13.7 11.1 34.0 18.2 0.081 P6KE150A P6KE150CA 150.0 143.0 158.0 128.0 3.0 207.0 0.108 P6KE15A P6KE15CA 15.0 14.3 15.8 12.8 29.0 21.2 0.084 P6KE160A P6KE160CA 160.0 152.0 168.0 136.0 2.8 219.0 0.108 P6KE16A P6KE16CA 16.0 15.2 16.8 13.6 28.0 22.5 0.086 P6KE180A P6KE180CA 180.0 171.0 189.0 154.0 2.5 246.0 0.108 P6KE18A P6KE18CA 18.0 17.1 18.9 15.3 25.0 25.2 0.088 P6KE200A P6KE200CA 200.0 190.0 210.0 171.0 2.2 274.0 0.108 P6KE20A P6KE20CA 20.0 19.0 21.0 17.1 22.0 27.7 0.090 P6KE22A P6KE22CA 22.0 20.9 23.1 18.8 20.0 30.6 0.092 P6KE24A P6KE24CA 24.0 22.8 25.2 20.5 19.0 33.2 0.094 P6KE27A P6KE27CA 27.0 25.7 28.4 23.1 16.8 37.5 0.096 P6KE300A P6KE300CA 300.0 285.0 315.0 256.0 1.5 414.0 0.110 P6KE30A P6KE30CA 30.0 28.5 31.5 25.6 15.0 41.4 0.097 P6KE33A P6KE33CA 33.0 31.4 34.7 28.2 13.8 45.7 0.098 P6KE36A P6KE36CA 36.0 34.2 37.8 30.8 12.6 49.9 0.099 P6KE39A P6KE39CA 39.0 37.1 41.0 33.3 11.6 53.9 0.100 P6KE400A P6KE400CA 400.0 380.0 420.0 342.0 1.1 548.0 P6KE440A P6KE440CA 440.0 418.0 462.0 376.0 1.04 600.0 P6KE47A P6KE47CA 47.0 44.7 49.4 40.2 9.7 64.8 P6KE62A P6KE62CA 62.0 58.9 65.1 53.0 7.4 85.0 P6KE68A P6KE68CA 68.0 64.6 71.4 58.1 6.8 92.0 P6KE7.5A P6KE7.5CA 7.5 7.13 7.88 55.0 11.3 0.107 1.0 5.0 0.110 0.101 0.104 10.0 Page <4> 6.40 500.0 0.061 19/05/08 V1.1 P6KE Series Electrical Characteristics (TA = 25C unless otherwise noted) Breakdown Voltage Device Unidirectional Bidirectional Maximum Maximum Maximum Test Stand-Off Reverse Peak Clamping Maximum Nominal VBR (Volts) (Note 1) Current Voltage Pulse Leakage Voltage Temperature Voltage at IT VWM Coefficient Current I RSM at VWM at IPPM (Volts) of VBR(%/C) (mA) (Volts) (Note 2) A) ID ( VC(Volts) Minimum Maximum (Amps) P6KE8.2A P6KE8.2CA 8.2 7.79 8.61 P6KE9.1A P6KE9.1CA 9.1 8.65 9.55 P6KE91A P6KE91CA 91.0 86.5 95.5 1.0 7.02 200.0 52.0 12.1 0.064 7.78 50.0 47.0 13.4 0.068 77.8 5.0 5.0 125.0 0.106 Notes: 1. VBR measured after IT applied for 300s, IT = square wave pulse or equivalent. 2. Surge current waverform per Figure 3 and derate. 3. For bipolar types having VWM of 10 volts and under, the ID limit is doubled. 4. All terms and symbols are consistent with ANSI/IEEE C62.35. Page <5> 19/05/08 V1.1 P6KE Series Notes: International Sales Offices: AUSTRALIA - Farnell FINLAND - Farnell ITALY - Farnell SPAIN - Farnell Tel No: Tel No: Tel No: Tel No: ++61 1300 361 005 ++ 358 9 560 7780 ++ 39 02 93 995 200 901 20 20 80 Fax No: ++61 1300 361 225 Fax No: ++ 358 9 345 5411 Fax No: ++ 39 02 93 995 300 Fax No: 901 20 20 90 AUSTRIA - Farnell FRANCE - Farnell SWEDEN - Farnell Tel No: Tel No: Fax No: ++ 43 662 2180 670 Fax No: ++ 33 474 68 99 90 MALAYSIA - Farnell-Newark Tel No: ++ 60 3 7873 8000 Fax No: ++ 60 3 7873 7000 BELGIUM - Farnell GERMANY - Farnell NETHERLANDS - Farnell SWITZERLAND - Farnell Tel No: Tel No: Tel No: ++ 43 662 2180 680 ++ 33 474 68 99 99 Tel No: ++ 46 8 730 50 00 Fax No: ++ 46 8 83 52 62 Fax No: ++ 32 3 227 3648 Fax No: ++ 49 89 613 59 01 Fax No: ++ 31 30 241 7333 Tel No: ++ 44 204 64 64 Fax No: ++ 44 204 64 54 BRAZIL - Farnell-Newark HONG KONG - NEW ZEALAND - Farnell UK - Farnell Tel No: Tel No: ++ 32 3 475 2810 ++ 49 89 61 39 39 39 ++ 31 30 241 7373 ++ 55 11 4066 9400 Farnell-Newark Tel No: ++ 852 2268 9888 Fax No: ++ 55 11 4066 9410 Fax No: ++ 852 2268 9899 Fax No: 0800 90 80 81 Fax No: ++ 44 8701 200 201 CHINA - Farnell-Newark HUNGARY - Farnell NORWAY - Farnell UK - CPC Tel No: Tel No: Tel No: 800 146 70 ++ 44 8701 202 530 Tel No: ++86 10 6238 5152 ++ 44 870 1200 208 0800 90 80 80 ++ 44 8701 200 200 Fax No: ++86 10 6238 5022 Fax No: ++ 44 870 1200 209 Fax No: 800 146 76 ++ 44 8701 202 531 CZECH REPUBLIC - Farnell INDIA - Farnell PORTUGAL - Farnell USA - Tel No: Tel No: Tel No: ++ 44 870 1200 208 ++ 44 870 1200 208 Fax No: ++ 44 870 1200 209 Fax No: ++ 44 870 1200 209 Fax No: ++ 34 93 474 5288 DENMARK - Farnell IRELAND - Farnell RUSSIA - Farnell Tel No: Tel No: Tel No: ++ 45 44 53 66 44 Fax No: ++ 45 44 53 66 06 ++ 353 1 830 9277 ++ 44 870 1200 208 Fax No: ++ 44 870 1200 209 Fax No: ++ 353 1 830 9016 Newark ++ 34 93 475 8804 Tel No: export 800 463 9275 EXPORT - Farnell Tel No: ++ 44 8701 200 208 Fax No: ++ 44 8701 200 209 For enquiries from all other markets ESTONIA - Farnell ISRAEL - Farnell Tel No: Tel No: ++ 358 9 560 7780 Fax No: ++ 358 9 345 5411 SINGAPORE - Farnell-Newark Tel No: ++ 65 6788 0200 ++ 180 937 0015 Fax No: ++ 180 937 0014 Fax No: ++ 65 6788 0300 http://www.farnell.com http://www.newark.com http://www.cpc.co.uk Disclaimer This data sheet and its contents (the "Information") belong to the Premier Farnell Group (the "Group") or are licensed to it. No licence is granted for the use of it other than for information purposes in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, any error in or omission from it or for any use made of it. Users of this data sheet should check for themselves the Information and the suitability of the products for their purpose and not make any assumptions based on information included or omitted. Liability for loss or damage resulting from any reliance on the Information or use of it (including liability resulting from negligence or where the Group was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group's liability for death or personal injury resulting from its negligence. SPC Multicomp is the registered trademark of the Group. (c) Premier Farnell plc 2008. Page <6> 19/05/08 V1.1