Headphone Amplifiers Coupling Capacitorless Headphone Amplifiers No.11102EAT04 BD88200GUL,BD88210GUL,BD88215GUL,BD88220GUL Description BD88xxxGUL is output coupling capacitorless headphone amplifier. This IC has a negative voltage generator of regulated type built-in and generates the direct regulated negative voltage from the supply voltage. It is possible to drive headphones in a ground standard with both voltage of the positive voltage (+2.4V) and the negative voltage (-2.4V). Therefore a large-capacity output coupling capacitor becomes needless and can reduce a cost, a board area, and the height of the part. In addition, there is not the signal decrement by the low range to happen by output coupling capacitor and output load impedance and can output a rich low tone. And, the function "Virtual ground" is embedded. Noise between IC and Headphone jack can be canceled by using "Virtual ground" function. Features 1) 2.4V to 5.5V Single-Supply Operation 2) No Bulky DC-Blocking Capacitors Required 3) No Degradation of Low-Frequency Response Due to Output Capacitors 4) Virtual Ground-Referenced Outputs 5) Gain setting BD88200GUL: Variable gain with external resistors BD88210GUL: -1.0V/V BD88215GUL: -1.5V/V BD88220GUL: -2.0V/V 6) Low THD+N 7) Low Supply Current 8) Integrated Negative Power Supply 9) Integrated Short-Circuit and Thermal-Overload Protection 10) Small package VCSP50L2 (2.1mm x 2.1mm) Applications Mobile Phones, Smart Phones, PDAs, Portable Audio Players, PCs, TVs, Digital Cameras, Digital Video Cameras, Electronic Dictionaries, Voice Recorders, Bluetooth Head-sets, etc Line up Type Supply Supply Voltage Current [V] [mA] Gain [V/V] Maximum Output Power [mW] THD+N [%] 80 0.006 Noise Voltage [Vrms] PSRR [dB] Package Variable gain with external resister BD88200GUL BD88210GUL -1.0 2.45.5 (No2.0 signal) BD88215GUL -1.5 BD88220GUL -2.0 www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. (VDD=3.3V,RL=16 (VDD=3.3V,RL=16 THD+N1%,f=1kHz) Po=10mW,f=1kHz) 1/22 10 -80 VCSP50L2 (f=217Hz) (2.1mm x 2.1mm) 2011.03 - Rev. A Technical Note BD88200GUL,BD88210GUL,BD88215GUL,BD88220GUL Absolute maximum ratings Parameter Symbol Ratings Unit SGND to PGND voltage VGG 0.0 V SVDD to PVDD voltage VDD -0.3 to 0.3 V SVSS to PVSS voltage VSS 0.0 V SGND or PGND to SVDD, PVDD voltage VDG -0.3 to 6.0 V SVSS, PVSS to SGND or PGND voltage VSG -3.5 to 0.3 V SGND to IN_- voltage VIN (SVSS-0.3) to 2.8 V SGND to OUT_- voltage VOUT (SVSS-0.3) to 2.8 V SGND to COM_- voltage VCOM (SVSS-0.3) to 2.8 V PGND to C1P- voltage VC1P (PGND-0.3) to (PVDD+0.3) V PGND to C1N- voltage VC1N (PVSS-0.3) to (PGND+0.3) V SGND to SHDN_B- voltage VSH (SGND-0.3) to (SVDD+0.3) V Input current IIN -10 to 10 mA Power Dissipation PD 1350 * mW TSTG -55 to 150 Storage Temperature Range * In operating over 25 , de-rate the value to 10.8mW/. This value is for mounted on the application board (Grass-epoxy, size: 40mm x 60mm, H=1.6mm, Top Copper area = 79.9%, Bottom Copper area = 80.2%). Operating conditions Parameter Supply Voltage Range Operating Temperature Range www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. Ratings Symbol Unit Min. Typ. Max. VSVDD,VPVDD 2.4 - 5.5 V TOPR -40 - +85 2/22 2011.03 - Rev. A Technical Note BD88200GUL,BD88210GUL,BD88215GUL,BD88220GUL Electrical characteristics Unless otherwise specified, Ta=25, SVDD=PVDD=3.3V, SGND=PGND=0V, SHDNB=SVDD, C1=C2=2.2F, RL=No Load, Ri=Rf=10k Limits Parameter Symbol Unit Conditions Min. Typ. Max. Supply Current Shutdown Supply Current IST - 0.1 2 A SHDNB=L Quiescent Supply Current IDD - 2.0 7.4 mA SHDNB=H, No signal H Level Input Voltage VIH 1.95 - - V L Level Input Voltage VIL - - 0.70 V ILEAK - - 1 A Shutdown to Full Operation tSON - 80 - s Offset Voltage VIS - 0.5 5.0 mV 30 60 - mW 40 80 - mW - 0.008 0.056 % - 0.006 0.100 % 10 14 19 k - -1.00 - -1.05 -1.00 -0.95 SHDN_B Terminal Input Leak Current Headphone Amplifier Maximum Output Power Total Harmonic Distortion + Noise POUT THD+N Input Impedance ZIN BD88200GUL BD88210GUL Gain AV V/V BD88215GUL -1.55 -1.50 -1.45 BD88220GUL -2.06 -2.00 -1.94 AV - 1 - % Noise VN - 10 - Vrms Slew Rate SR - 0.15 - V/s Maximum Capacitive Load CL - 200 - pF Crosstalk CT - -90 - dB PSRR - -80 - dB Charge-Pump Oscillator Frequency fOSC 200 300 430 kHz Thermal-Shutdown Threshold TSD - 145 - Thermal-Shutdown Hysteresis THYS - 5 - Gain match Power Supply Rejection Ratio www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 3/22 SHDNB=LH RL=32, THD+N1%, f=1kHz, 20kHz LPF, for Single Channel RL=16, THD+N1%, f=1kHz, 20kHz LPF, for Single Channel RL=32, POUT=10mW, f=1kHz, 20kHz LPF RL=16, POUT=10mW, f=1kHz, 20kHz LPF SHDNB=H In BD88200GUL, ZIN = Ri In BD88200GUL, Gain is variable by the external resister of Ri and Rf. 20kHz LPF + A-weight RL=32, f=1kHz, VOUT=200mVP-P, 1kHz BPF f=217Hz, 100mVP-Pripple, 217Hz BPF 2011.03 - Rev. A Technical Note BD88200GUL,BD88210GUL,BD88215GUL,BD88220GUL Electrical characteristic curves - General Items (Reference data) Unless otherwise specified, Ta=25, SGND=PGND=0V,SHDNB=SVDD, C1=C2=2.2F, Input coupling capacitor=1F, RL=No Load * In BD88200GUL the input resister(Ri)=10k, feedback resister(Rf)=10k. 4.0 1u [mA] SHDNB=VDD 100n Operating Current Standby Current [A] SHDNB=0V 10n 1n 0.1n 0.0 1.0 2.0 3.0 4.0 5.0 * This caracteristics has hysteresis (40mV typ) by UVLO. 3.0 2.0 1.0 0.0 0.0 6.0 1.0 -2 140 Maximum Output Power [mW] Setup time [us] VSS Voltage [V] 160 -1.5 120 100 80 60 40 -2.5 RL=16, out of phase 100 80 60 RL=32, in phase 40 RL=32, out of phase THD+N-40dB 20kHz LPF Stereo 20 20 -3 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 0 0 0 VDD=2.4V Ripple = 100mVp-p BPF -20 -20 -60 -40 -50 -60 -40 -50 -60 -70 -70 -70 -80 -80 -80 -90 -90 -90 -100 -100 -100 1k 10k 10 100k 100 1k 10k 100k 10 -20 -30 PSRR [dB] -30 -40 -50 -60 -20 -30 -40 -50 -60 -40 -50 -60 -70 -70 -80 -80 -80 -90 -90 -90 -100 -100 -100 100 1k 10k 100k Frequency [Hz] Fig.10 Crosstalk vs. Frequency (VDD=2.4V) www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 10 100 1k 10k Frequency [Hz] Fig.11 Crosstalk vs. Frequency (VDD=3.3V) 4/22 VDD=5.5V VOUT = 200mVp-p RL=32 BPF -10 -70 10 100k 0 VDD=3.3V VOUT = 200mVp-p RL=32 BPF -10 PSRR [dB] -20 10k Frequency [Hz] 0 VDD=2.4V VOUT = 200mVp-p RL=32 BPF 1k Fig.9 PSRR vs. Frequency (VDD=5.5V) Fig.8 PSRR vs. Frequency (VDD=3.3V) 0 -10 100 Frequency [Hz] Frequency [Hz] Fig.7 PSRR vs. Frequency (VDD=2.4V) 6.0 -30 PSRR [dB] PSRR [dB] PSRR [dB] -50 5.0 5.5 VDD=5.5V Ripple = 100mVp-p BPF -10 -30 -40 4.0 4.5 0 VDD=3.3V Ripple = 100mVp-p BPF -10 -30 3.0 3.5 Fig.6 Maximum power vs. Supply Voltage Fig.5 Setup time vs. Supply Voltage 0 2.5 Supply Voltage [V] Supply Voltage [V] Supply Voltage [V] PSRR [dB] 2.0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 Fig.4 Negative Voltage vs. Supply Voltage 100 6.0 RL=16, in phase SHDNB =L->H VSS 90% Setup time No Load 180 -1 10 5.0 120 200 SHDNB=VDD No Load -20 4.0 Fig.3 Operating Current vs. Supply voltage 0 -10 3.0 Supply Voltage [V] Supply Voltage [V] Fig.1 Standby Current vs. Supply Voltage -0.5 2.0 100k 10 100 1k 10k 100k Frequency [Hz] Fig.12 Crosstalk vs. Frequency (VDD=5.5V) 2011.03 - Rev. A Technical Note BD88200GUL,BD88210GUL,BD88215GUL,BD88220GUL Electrical characteristic curves - BD88215GUL (Reference data) -20 Output Voltage [dBV] -40 RL=16 -60 -80 -40 RL=16 -60 -80 -120 -120 -100 -80 -60 -40 -20 -120 -120 0 10 8 8 RL=16 6 -100 -80 -60 -80 -40 -20 -120 -120 0 VDD=2.4V Po=10mW RL=16 Input coupling capacitor = 1.0uF -4 -6 -8 100 RL=32 -2 VDD=3.3V Po=10mW RL=16 Input coupling capacitor = 1.0uF -4 -6 -8 1k 10k 2 10 100 -6 -8 10k 100k 10 10 0.01 THD+N [%] 10 THD+N [%] 10 1 In phase 0.1 VDD=3.3V 20kHz-LPF f=1kHz Stereo RL=16 0.01 Out of phase 1n 100n 10u 1m 1n 100m 100n 1 0.1 Out of phase 10u 1m 1n 100m 10 10 THD+N [%] 10 0.1 VDD=2.4V 20kHz-LPF f=1kHz Stereo RL=32 0.01 In phase 0.1 VDD=3.3V 20kHz-LPF f=1kHz Stereo RL=32 0.01 Out of phase 1n 100n 10u 1m 100m Output Power [W] Fig.22 THD+N vs. Output Power (VDD=2.4V, RL=32) www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 1 1m 100m In phase 0.1 VDD=5.5V 20kHz-LPF f=1kHz Stereo RL=32 0.01 Out of phase Out of phase 0.001 0.001 0.001 10u Fig.21 THD+N vs. Output Power (VDD=5.5V, RL=16) 100 1 100n Output Power [W] Fig.20 THD+N vs. Output Power (VDD=3.3V, RL=16) 100 In phase Out of phase 0.001 100 1 VDD=5.5V 20kHz-LPF f=1kHz Stereo RL=16 Output Power [W] Output Power [W] Fig.19 THD+N vs. Output Power (VDD=2.4V, RL=16) 100k In phase 0.01 0.001 0.001 10k Frequency [Hz] 100 In phase 1k Fig.18 Gain vs. Frequency (VDD=5.5V) 100 VDD=2.4V 20kHz-LPF f=1kHz Stereo RL=16 100 Frequency [Hz] Fig.17 Gain vs. Frequency (VDD=3.3V) 100 0.1 VDD=5.5V Po=10mW RL=16 Input coupling capacitor = 1.0uF -4 1k Frequency [Hz] 1 RL=32 0 -2 -10 100k Fig.16 Gain vs. Frequency (VDD=2.4V) 0 RL=16 6 -10 10 -20 4 0 -10 -40 8 RL=16 Gain [dB] -2 -60 Fig.15 Output Voltage vs. Input Voltage (VDD=5.5V) 2 Gain [dB] RL=32 0 -80 Input Voltage [dBV] 4 2 -100 10 6 4 Gain [dB] RL=16 -60 Fig.14 Output Voltage vs. Input Voltage (VDD=3.3V) Fig.13 Output Voltage vs. Input Voltage (VDD=2.4V) THD+N [%] -40 Input Voltage [dBV] 10 RL=32 -100 Input Voltage [dBV] THD+N [%] -20 -100 -100 VDD=5.5V f=1kHz BPF 0 RL=32 THD+N [%] Output Voltage [dBV] -20 VDD=3.3V f=1kHz BPF 0 RL=32 Output Voltage [dBV] VDD=2.4V f=1kHz BPF 0 1n 100n 10u 1m 100m Output Power [W] Fig.23 THD+N vs. Output Power (VDD=3.3V, RL=32) 5/22 1n 100n 10u 1m 100m Output Power [W] Fig.24 THD+N vs. Output Power (VDD=5.5V, RL=32) 2011.03 - Rev. A Technical Note BD88200GUL,BD88210GUL,BD88215GUL,BD88220GUL Electrical characteristic curves - BD88215GUL (Reference data) - Continued 100 VDD=2.4V RL=16 20kHz-LPF Stereo (in phase) 1 10 THD+N [%] Po=0.1mW Po=1mW 0.1 1 Po=0.1mW Po=1mW 0.1 0.01 0.01 Po=10mW 0.001 10 100 1k Po=10mW 10 100k 100 Frequency [Hz] Po=0.1mW Po=10mW Po=1mW 10 100 1k Po=1mW 100 1k 10k 0.1 10 Spectrum [dBV] -80 -40 -60 -80 -40 -60 -80 -120 -120 -120 -140 100k Frequency [Hz] Fig.31 Noise Spectrum (VDD=2.4V) www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 100k VDD=5.5V Input connect to the ground with 1uF -20 -100 10k 10k 0 VDD=3.3V Input connect to the ground with 1uF -100 -140 1k Fig. 30 THD+N vs. Frequency (VDD=5.5V, RL=32) -100 1k 100 Frequency [Hz] Fig. 29 THD+N vs. Frequency (VDD=3.3V, RL=32) -20 -60 100 Po=1mW 0.001 100k 0 VDD=2.4V Input connect to the ground with 1uF 10 Po=0.1mW Po=10mW Frequency [Hz] Frequency [Hz] -40 1 0.01 10 0 100k VDD=5.5V RL=32 20kHz-LPF Stereo (in phase) 10 Po=10mW 0.1 100k 10k Frequency [Hz] Po=0.1mW 0.001 10k 1k 100 1 Fig. 28 THD+N vs. Frequency (VDD=2.4V, RL=32) -20 100 Fig. 27 THD+N vs. Frequency (VDD=5.5V, RL=16) 0.01 0.001 Po=10mW 10 100k THD+N [%] THD+N [%] THD+N [%] 10k VDD=3.3V RL=32 20kHz-LPF Stereo (in phase) 10 0.01 Spectrum [dBV] 1k 100 VDD=2.4V RL=32 20kHz-LPF Stereo (in phase) 0.1 0.1 Frequency [Hz] 100 1 Po=0.1mW Po=1mW 0.001 Fig. 26 THD+N vs. Frequency (VDD=3.3V, RL=16) Fig.25 THD+N vs. Frequency (VDD=2.4V, RL=16) 10 1 0.01 0.001 10k VDD=5.5V RL=16 20kHz-LPF Stereo (in phase) 10 Spectrum [dBV] THD+N [%] 10 100 VDD=3.3V RL=16 20kHz-LPF Stereo (in phase) THD+N [%] 100 -140 10 100 1k 10k Frequency [Hz] Fig.32 Noise Spectrum (VDD=3.3V) 6/22 100k 10 100 1k 10k 100k Frequency [Hz] Fig.33 Noise Spectrum (VDD=5.5V) 2011.03 - Rev. A Technical Note BD88200GUL,BD88210GUL,BD88215GUL,BD88220GUL Electrical characteristic curves - BD88200GUL (Reference data) 100 10 VDD=3.3V f=1kHz BPF -20 RL=32 VDD=3.3V, Po=10mW Ri=10k, Input coupling capacitor = 1.0uF 8 6 10 4 RL=16 -60 RL=16 2 THD+N [%] -40 Gain [dB] Output Voltage [dBV] 0 0 -2 -80 RL=32 In phase 1 0.1 VDD=3.3V 20kHz-LPF f=1kHz Stereo RL=16 -4 0.01 -6 -100 -8 -120 -120 -100 -80 -60 -40 -20 10 0 100 Input Voltage [dBV] 10k 1n 100k 0.1 VDD=3.3V 20kHz-LPF f=1kHz Stereo RL=32 0.01 1 Po=0.1mW Po=1mW 0.1 Out of phase 100n 10u 1m 100m Output Power [W] 10 100 1k 10k Frequency [Hz] Fig. 37 THD+N vs. Output Power (VDD=3.3V, RL=32) Po=0.1mW Po=1mW 0.1 Po=10mW Po=10mW 0.001 1n 1 0.01 0.01 0.001 100m VDD=3.3V RL=32 20kHz-LPF Stereo (in phase) 10 THD+N [%] THD+N [%] In phase 1m 100 VDD=3.3V RL=16 20kHz-LPF Stereo (in phase) 10 1 10u Output Power [W] 100 10 100n Fig.36 THD+N vs. Output Power (VDD=3.3V, RL=16) Fig.35 Gain vs. Frequency (VDD=3.3V) 100 THD+N [%] 1k Frequency [Hz] Fig.34 Output Voltage vs. Input Voltage (VDD=3.3V) Out of phase 0.001 -10 Fig.38 THD+N vs. Frequency (VDD=3.3V, RL=16) 0.001 100k 10 100 1k 10k 100k Frequency [Hz] Fig. 39 THD+N vs. Frequency (VDD=3.3V, RL=32) 0 VDD=3.3V Input connect to the ground with 1uF Spectrum [dBV] -20 -40 -60 -80 -100 -120 -140 10 100 1k 10k 100k Frequency [Hz] Fig.40 Noise Spectrum (VDD=3.3V) www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 7/22 2011.03 - Rev. A Technical Note BD88200GUL,BD88210GUL,BD88215GUL,BD88220GUL Electrical characteristic curves - BD88210GUL (Reference data) 100 10 VDD=3.3V Po=10mW Input coupling capacitor = 1.0uF 8 6 4 -40 Gain [dB] Output Voltage [dBV] -20 RL=32 RL=16 -60 -80 10 RL=16 2 THD+N [%] VDD=3.3V f=1kHz BPF 0 0 -2 RL=32 In phase 1 0.1 VDD=3.3V 20kHz-LPF f=1kHz Stereo RL=16 -4 0.01 -6 -100 -8 -120 -120 -100 -80 -60 -40 -20 10 0 100 VDD=3.3V 20kHz-LPF f=1kHz Stereo RL=32 1n 1 Po=1mW 0.1 100m Output Power [W] Po=10mW Po=1mW 0.1 Po=0.1mW 10 100 1k 10k Po=10mW 0.001 100k Frequency [Hz] Fig.45 THD+N vs. Frequency (VDD=3.3V, RL=16) Fig. 44 THD+N vs. Output Power (VDD=3.3V, RL=32) 1 0.01 0.001 1m 100m VDD=3.3V RL=32 20kHz-LPF Stereo (in phase) 10 Po=0.1mW Out of phase 10u 1m 100 0.01 100n 10u Output Power [W] THD+N [%] THD+N [%] THD+N [%] In phase 100n Fig.43 THD+N vs. Output Power (VDD=3.3V, RL=16) VDD=3.3V RL=16 20kHz-LPF Stereo (in phase) 10 1 0.001 1n 100k 100 10 0.01 10k Fig.42 Gain vs. Frequency (VDD=3.3V) 100 0.1 1k Frequency [Hz] Input Voltage [dBV] Fig.41 Output Voltage vs. Input Voltage (VDD=3.3V) Out of phase 0.001 -10 10 100 1k 10k 100k Frequency [Hz] Fig. 46 THD+N vs. Frequency (VDD=3.3V, RL=32) 0 VDD=3.3V Input connect to the ground with 1uF Spectrum [dBV] -20 -40 -60 -80 -100 -120 -140 10 100 1k 10k 100k Frequency [Hz] Fig.47 Noise Spectrum (VDD=3.3V) www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 8/22 2011.03 - Rev. A Technical Note BD88200GUL,BD88210GUL,BD88215GUL,BD88220GUL Electrical characteristic curves - BD88220GUL (Reference data) 10 VDD=3.3V f=1kHz BPF -20 RL=32 100 RL=16 8 6 10 4 RL=16 -60 -80 RL=32 2 0 -2 VDD=3.3V Po=10mW Input coupling capacitor = 1.0uF -4 -6 -100 -8 -120 -120 -100 -80 -60 -40 -20 100 1k 10k 100k 1n 0.01 0.001 1n 100n 1 Po=0.1mW Po=1mW 0.1 0.01 Po=10mW 0.001 1m 100m 10 100 1k 10k 1 Po=1mW 0.1 Po=0.1mW Po=10mW 0.001 100k Frequency [Hz] Output Power [W] Fig. 51 THD+N vs. Output Power (VDD=3.3V, RL=32) 100m 0.01 Out of phase 10u 1m VDD=3.3V RL=32 20kHz-LPF Stereo (in phase) 10 THD+N [%] THD+N [%] VDD=3.3V 20kHz-LPF f=1kHz Stereo RL=32 10u 100 VDD=3.3V RL=16 20kHz-LPF Stereo (in phase) 10 In phase 100n Fig.50 THD+N vs. Output Power (VDD=3.3V, RL=16) 100 10 Out of phase Output Power [W] Fig.49 Gain vs. Frequency (VDD=3.3V) 100 0.1 VDD=3.3V 20kHz-LPF f=1kHz Stereo RL=16 Frequency [Hz] Input Voltage [dBV] 1 0.1 0.001 10 0 In phase 1 0.01 -10 Fig.48 Output Voltage vs. Input Voltage (VDD=3.3V) THD+N [%] THD+N [%] -40 Gain [dB] Output Voltage [dBV] 0 Fig.52 THD+N vs. Frequency (VDD=3.3V, RL=16) 10 100 1k 10k 100k Frequency [Hz] Fig. 53 THD+N vs. Frequency (VDD=3.3V, RL=32) 0 VDD=3.3V Input connect to the ground with 1uF Spectrum [dBV] -20 -40 -60 -80 -100 -120 -140 10 100 1k 10k 100k Frequency [Hz] Fig.54 Noise Spectrum (VDD=3.3V) www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 9/22 2011.03 - Rev. A Technical Note BD88200GUL,BD88210GUL,BD88215GUL,BD88220GUL Pin Arrangement 1 2 3 4 SVDD OUTL SVSS PVSS C INL OUTR C1N B SHDNB COM PGND A INR D Pin Function Ball Pin name Matrix A1 INR SGND PVDD (Bottom View) C1P Function Symbol Headphone Amplifier (Rch) input C A2 SGND Ground for Headphone Amplifier - A3 PVDD Positive Power Supply for Charge Pump - A4 C1P Flying Capacitor (CF) Positive A B1 SHDNB Headphone Amplifier Shutdown Control (H:active, L:shutdown) E B2 COM Virtual Ground Input - B4 PGND Ground for Charge Pump - C1 INL C2 OUTR Headphone Amplifier (Lch) input C Headphone Amplifier (Rch) output D C4 C1N Flying Capacitor (CF) Negative B D1 SVDD Ground for Headphone Amplifier - D2 OUTL Headphone Amplifier (Lch) output D D3 SVSS Negative Supply Voltage for Signal - D4 PVSS Negative Supply Voltage output F Pin equivalent circuit PGND PGND PVDD PVDD SVDD - PAD PAD PAD + A B PGND PGND C PVSS PVSS SVDD SVDD SVSS PGND PGND PAD PAD PAD + D SVSS E SGND F Fig.55 Pin equivalent circuit www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 10/22 2011.03 - Rev. A Technical Note BD88200GUL,BD88210GUL,BD88215GUL,BD88220GUL INL SHDNB Block Diagram B1 C1 SVDD SVDD Rin D1 Rfb PVDD A3 SVDD OUTL 1.0F D2 R2=Rin C1P + A4 SGND SVSS SVDD R1=Rfb PGND B4 SVDD CHARGE PUMP UVLO/ SHUTDOWN CONTROL SHORT PROTECTION TSD COM C1N B2 R1=Rfb C4 PVSS SVDD PVDD SGND CHARGE PUMP CONTROL SVSS OUTR + CLOCK GENERATOR R2=Rin C2 - D4 SVDD Rin R fb SVSS SVSS SGND A1 INR SGND A2 D3 Type Rin Rfb BD88200GUL 14k@Typ. Open BD88210GUL 14k@Typ. 14k@Typ. BD88215GUL 14k@Typ. 21k@Typ. BD88220GUL 14k@Typ. 28k@Typ. Fig.56 Block Diagram www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 11/22 2011.03 - Rev. A Technical Note BD88200GUL,BD88210GUL,BD88215GUL,BD88220GUL Functional descriptions The conventional headphone amplifier composition is occupied to Fig.57. In this composition, the signal is output by using the middle point bias circuit based on the middle point bias. Therefore, the output coupling capacitor that removes the DC voltage difference and does the AC coupling is necessary. This coupling capacitor and the impedance of the headphone composes the high-pass filter. Therefore, the signal degradation in the low frequency region learns by experience. The output coupling capacitor should be a large capacity, because the cutoff frequency of this high-pass filter becomes the following formula (1). 1 fc (1) 2RLCC * Cc is the coupling capacitor, and RL is the impedance of the headphone. Moreover, POP noise by the middle point bias start-up is generated and the degradation of PSRR learns by experience. VDD Cc + Vhp VDD Vout [V] + Vout Input VDD/2 0 time [s] Vhp [V] GND Middle Point BiasCircuit 0 time [s] Fig.57 Conventional headphone amplifier composition The composition of the series of BD882xxGUL is occupied to Fig.58. In this composition, the signal is output by using a negative voltage based on the ground level. Therefore, the amplifier output can be connected directly with the headphone. And, the output coupling capacitor becomes unnecessary. Additionally, the signal degradation in the low frequency region with the coupling capacitor is not generated, and the deep bass is achieved. Moreover, POP noise is controlled because of no middle point bias start-up. And, the degradation of PSRR doesn't occur by being based on the ground. Vout Input + CF : Flying Capacitor VDD Vout [V] HPVDD Vhp HPVDD 0 time [s] Charge Pump Vhp [V] VSS CH : Hold Capacitor 0 time [s] Fig.58 Composition of the series of BD882xxGUL www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 12/22 2011.03 - Rev. A Technical Note BD88200GUL,BD88210GUL,BD88215GUL,BD88220GUL BD882GUL has the function "Virtual Ground-reference output". "Virtual Ground-reference output" can be canceled Noise (see Fig.59 "Vn") between IC and headphone jack by feedback ground of headphone jack to IC. Vout Vo + Vout Vn=Vg Voltage[V] VDD Voltage[V] Input 0 Vo 0 time[s] time[s] Vn Charge Pump GND Vg (Ground-bias type) Vout Vo + Vout Vn=Vg Voltage[V] VDD Voltage[V] Input Vo 0 0 time[s] time[s] Vn Charge Pump GND Vg (Virtual ground-bias type) Fig.59. Ground noise canceling function by "virtual ground" Connect Pin "B2" (COM) to ground near headphone jack. In case of BD88200GUL, value error of external resistors makes noise rejection characteristic worse. Put "External resistors" that have high accuracy within 5%, near the LSI. www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 13/22 2011.03 - Rev. A Technical Note BD88200GUL,BD88210GUL,BD88215GUL,BD88220GUL [CHARGE PUMP / CHARGE PUMP CONTROL] The negative power supply circuit is composed of the regulated charge-pump. This circuit outputs the regulated negative voltage (PVSS) directly from power-supply voltage (PVDD). Therefore, it doesn't depend on the power-supply voltage, and a constant voltage is output (PVSS=-2.4V@Typ., refer to Fig.4). Moreover, there is not swinging of the power supply by the output current of the headphone amplifier, and it doesn't influence the headphone amplifier characteristic. 0 Ta=25 VDD=3.3V SHDNB=SVDD CF=CH=2.2uF VSS Voltage [V] -0.5 -1 -1.5 -2 -2.5 -3 0 20 40 60 80 Load Current [mA] Fig.60 Characteristics of load current regulation of PVSS (Reference data) Operating Frequency The operating frequency of the negative power supply charge pump is designed for the temperature and the voltage dependence may decrease. The reference data (measurements) is occupied to Fig.60. Please note the interference with the frequency in the application board. 400 380 360 Charge Pump Ocsillator Frequency [kHz] Charge Pump Ocsillator Frequency [kHz] 400 VDD=3.3V Measure : C1P CF=CH=2.2uF 340 320 300 280 260 240 220 200 -50.0 0.0 50.0 380 360 340 320 300 280 260 240 220 200 2.0 100.0 Ta=25 Measure : C1P CF=CH=2.2uF 3.0 4.0 5.0 6.0 Supply Voltage[V] Ta [] Fig.61 Temperature characteristic and Voltage characteristic of operating frequency (Reference data) The flying capacitor and the hold capacitor The flying capacitor (CF) and the hold capacitor (CH) greatly influence the characteristic of the charge pump. Therefore, please connect the capacitor with an excellent temperature characteristic and voltage characteristic of 2.2F as much as possible near IC. www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 14/22 2011.03 - Rev. A Technical Note BD88200GUL,BD88210GUL,BD88215GUL,BD88220GUL [HEADPHONE AMP] The headphone amplifier is driven by the internal positive voltage (+2.4V) and negative voltage (SVSS, -2.4V) based on ground (SGND). Therefore, the headphone can be connected without the output coupling capacitor. As a result, it brings the improved low-frequency characteristic compared with the headphone of the conventional coupling capacitor type. Power control When the SVSS voltage is -1.1V@Typ. or more, the headphone amplifier does not operate to protect from illegal operation. And in addition, the overcurrent protection circuit is built in. The amplifier is shutdown when the overcurrent occurs because of the output short-circuit etc., and IC is protected from being destroyed. [V] SHDNB VDD 0 [time] [V] 0 [time] -1.1V SVSS Amprilier Disable Amplifier Enable Fig.62 Area of headphone amplifier can operate SVSS does not have internal connection with PVSS. Please connect SVSS with PVSS on the application board. Input coupling capacitor Input DC level of BD882xxGUL is 0V (SGND). The input coupling capacitor is necessary for the connection with the signal source device. The signal decrease happens in the low frequency because of composing the high-pass filter by this input coupling capacitor and the input impedance of BD882xxGUL. The input impedance of BD882xxGUL is Rin (14k@Typ.). The cutoff frequency of this high-pass filter becomes the following formula. (In BD88200GUL, Rin becomes external resistance Ri. ) 1 fc (2) 2R in C in * Cin is the input coupling capacitor. 9.0 Rin=14k 6.0 3.0 Cin=10uF Gain [dB] 0.0 -3.0 -6.0 Cin=4.7uF -9.0 -12.0 Cin=2.2uF -15.0 Cin=1uF -18.0 -21.0 1 10 100 Frequency [Hz] Fig.63 Frequency response by the input coupling capacitor (Reference data) www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 15/22 2011.03 - Rev. A Technical Note BD88200GUL,BD88210GUL,BD88215GUL,BD88220GUL And, the degradation of THD+N happens because of the input coupling capacitor. Therefore, please consider these about the selection of parts. 0 -10 -20 Cin=1.0uF THD+N [dB] -30 -40 Cin=0.47uF BD88415GUL VDD=3.3V Po=10mW RL=16 20kHz LPF -50 -60 Cin=0.22uF -70 -80 -90 Cin=2.2uF -100 10 100 1k 10k 100k Frequency [Hz] * Capacitor size: 1608 Fig.64 THD+N by the input coupling capacitor (Reference data) Audio Source Vs Vin Rin =7.1k Cin Vs [V] State of terminal when power down The state of the terminal changes by the power control of the headphone amplifier. When it is shutdown, the input impedance of the input terminal becomes 7.1k@Typ. (In BD88200GUL, become Ri + 7.1k). The time constant can be reduced when the input coupling capacitor is charged. The input voltage changes while charging up the input coupling capacitor. Therefore, do not operate the headphone amplifier while charging. Vout VDD Output Bias 0 time [s] Vin [V] + Output Bias VSS 0 time [s] Fig.65 Input voltage transition with input coupling capacitor This charge time constant becomes the following formula (3) by using the input coupling capacitor and the input impedance. And the calculation value of the convergence to the wait time is indicated in Fig.65. R in C in (3) Convergence [%] * Rin=7.1k@Typ.. In BD88200GUL, Rin=Ri+7.1k 100 90 80 70 60 50 40 30 20 10 0 0 1 2 3 4 5 Wait time [s] 6 7 8 Fig.66 Wait time and convergence (Reference) www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 16/22 2011.03 - Rev. A Technical Note BD88200GUL,BD88210GUL,BD88215GUL,BD88220GUL [UVLO / SHUTDOWN CONTROL] BD882xxGUL has low voltage protection function (UVLO: Under Voltage Lock Out). And protect from the illegal operation of IC by a low power supply voltage. The detection voltage is 2.13V@Typ., so it does not influence 2.4V of recommended operation voltage. UVLO controls the whole of IC, and does both the negative power supply charge pump and the headphone amplifier in power down. [TSD] BD882xxGUL has overheating protection function (TSD: Thermal Shutdown). And the headphone amplifier becomes shutdown when illegally overheating by the headphone amplifier illegally operation. Timming Chart (Usually Operation) PVDD,SVDD SHDNB Amp enable PVSS,SVSS INL,INR OUTL OUTR Shutdown Setup Signal output Fig.67 Usually Operation Shutdown (UVLO Operation) Fig.68 UVLO Operation (TSD Operation) Fig.69 TSD Operation www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 17/22 2011.03 - Rev. A Technical Note BD88200GUL,BD88210GUL,BD88215GUL,BD88220GUL SHUTDOWN Control Lch Input INL SHDNB Application Circuit B1 1.0F 3.3V C1 SVDD SVDD D1 3.3V Rin Rfb 1.0F PVDD A3 SVDD OUTL 1.0F SGND SVDD CF SVSS R1=Rfb PGND CH SVDD C1 B4 Function value + A4 2.2F Part D2 R2=Rin C1P CHA RGE PUMP UVLO/ SHUTDOWN CONTROL SHORT PROTECTION TSD C2 Cpvdd COM 2.2F C1N C4 PVSS B2 R1=Rfb PVDD SVDD SGND CHARGE PUMP CONTROL OUTR + CLOCK GENERATOR Csvdd SVSS R2=Rin Cil C2 - Cir D4 SVDD Rin Flying Capacitor Hold Capacitor Bypass Capacitor Bypass Capacitor Coupling Capacitor Coupling Capacitor 2.2F 2.2F 1.0F 1.0F 1.0F 1.0F Remarks Temp. Characteristic Class-B Temp. Characteristic Class-B Temp. Characteristic Class-B Temp. Characteristic Class-B Temp. Characteristic Class-B Temp. Characteristic Class-B Rfb SVSS SVSS SGND A1 INR SGND A2 D3 1.0F Rch Input Fig.70 BD88210GU/BD88215GUL/BD88220GUL application circuit Part CF CH Cpvdd Csvdd Cil Cir Ri Rf Function Flying Capacitor Hold Capacitor Bypass Capacitor Bypass Capacitor Coupling Capacitor Coupling Capacitor Input Resistor Feedback Resistor value 2.2F 2.2F 1.0F 1.0F 1.0F 1.0F 10k 10k Remarks Temp. Characteristic Class-B Temp. Characteristic Class-B Temp. Characteristic Class-B Temp. Characteristic Class-B Temp. Characteristic Class-B Temp. Characteristic Class-B MCR006YZPJ103 (ROHM) MCR006YZPJ103 (ROHM) Fig.71 BD88200GUL application circuit In BD88200GUL, the Pass Gain becomes the following formula (4). The Pass Gain and the resister Rf is limited by table.3. R Gain f (4) Ri Table.3 Pass Gain and Resister Limit Item Min. Typ. Max. Unit Pass Gain 0.5 1.0 2.0 V/V Rf 1.0 10 - k Ri - 10 - k Ri is not limited. But, if this resister Ri is very small, the signal decrease happens in the low frequency (Refer to formula 2). www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 18/22 2011.03 - Rev. A Technical Note BD88200GUL,BD88210GUL,BD88215GUL,BD88220GUL Thermal Derating Curve The reference value of the thermal derating curve is indicated in Fig.71. (Conditions) This value is for mounted on the ROHM application board Board size40mm x 60mm x 1.6mm Top Copper Area79.9% Bottom Copper Area80.2% Board LayoutFig.74 1.6 1.4 Pd [W] 1.2 1 0.8 0.6 0.4 0.2 0 0 25 50 75 100 125 150 Ta [] Fig.72 Thermal Derating Curve www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 19/22 2011.03 - Rev. A BD88200GUL,BD88210GUL,BD88215GUL,BD88220GUL Technical Note Notes for use (1) Absolute Maximum Ratings An excess in the absolute maximum ratings, such as supply voltage, temperature range of operating conditions, etc., can break down devices, thus making impossible to identify breaking mode such as a short circuit or an open circuit. If any special mode exceeding the absolute maximum ratings is assumed, consideration should be given to take physical safety measures including the use of fuses, etc. (2) Operating conditions These conditions represent a range within which characteristics can be provided approximately as expected. The electrical characteristics are guaranteed under the conditions of each parameter. (3) Reverse connection of power supply connector The reverse connection of power supply connector can break down ICs. Take protective measures against the breakdown due to the reverse connection, such as mounting an external diode between the power supply and the IC's power supply terminal. (4) Power supply line Design PCB pattern to provide low impedance for the wiring between the power supply and the GND lines. In this regard, for the digital block power supply and the analog block power supply, even though these power supplies has the same level of potential, separate the power supply pattern for the digital block from that for the analog block, thus suppressing the diffraction of digital noises to the analog block power supply resulting from impedance common to the wiring patterns. For the GND line, give consideration to design the patterns in a similar manner. Furthermore, for all power supply terminals to ICs, mount a capacitor between the power supply and the GND terminal. At the same time, in order to use an electrolytic capacitor, thoroughly check to be sure the characteristics of the capacitor to be used present no problem including the occurrence of capacity dropout at a low temperature, thus determining the constant. (5) GND voltage Make setting of the potential of the GND terminal so that it will be maintained at the minimum in any operating state. Furthermore, check to be sure no terminals are at a potential lower than the GND voltage including an actual electric transient. (6) Short circuit between terminals and erroneous mounting In order to mount ICs on a set PCB, pay thorough attention to the direction and offset of the ICs. Erroneous mounting can break down the ICs. Furthermore, if a short circuit occurs due to foreign matters entering between terminals or between the terminal and the power supply or the GND terminal, the ICs can break down. (7) Operation in strong electromagnetic field Be noted that using ICs in the strong electromagnetic field can malfunction them. (8) Inspection with set PCB On the inspection with the set PCB, if a capacitor is connected to a low-impedance IC terminal, the IC can suffer stress. Therefore, be sure to discharge from the set PCB by each process. Furthermore, in order to mount or dismount the set PCB to/from the jig for the inspection process, be sure to turn OFF the power supply and then mount the set PCB to the jig. After the completion of the inspection, be sure to turn OFF the power supply and then dismount it from the jig. In addition, for protection against static electricity, establish a ground for the assembly process and pay thorough attention to the transportation and the storage of the set PCB. (9) Input terminals In terms of the construction of IC, parasitic elements are inevitably formed in relation to potential. The operation of the parasitic element can cause interference with circuit operation, thus resulting in a malfunction and then breakdown of the input terminal. Therefore, pay thorough attention not to handle the input terminals, such as to apply to the input terminals a voltage lower than the GND respectively, so that any parasitic element will operate. Furthermore, do not apply a voltage to the input terminals when no power supply voltage is applied to the IC. In addition, even if the power supply voltage is applied, apply to the input terminals a voltage lower than the power supply voltage or within the guaranteed value of electrical characteristics. (10) Ground wiring pattern If small-signal GND and large-current GND are provided, It will be recommended to separate the large-current GND pattern from the small-signal GND pattern and establish a single ground at the reference point of the set PCB so that resistance to the wiring pattern and voltage fluctuations due to a large current will cause no fluctuations in voltages of the small-signal GND. Pay attention not to cause fluctuations in the GND wiring pattern of external parts as well. (11) External capacitor In order to use a ceramic capacitor as the external capacitor, determine the constant with consideration given to a degradation in the nominal capacitance due to DC bias and changes in the capacitance due to temperature, etc. (12) About the rush current For ICs with more than one power supply, it is possible that rush current may flow instantaneously due to the internal powering sequence and delays. Therefore, give special consideration to power coupling capacitance, power wiring, width of GND wiring, and routing of wiring. www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 20/22 2011.03 - Rev. A Technical Note BD88200GUL,BD88210GUL,BD88215GUL,BD88220GUL Ordering part number B D 8 Part No. 8 2 1 5 G Part No. BD88200 BD88210 BD88215 BD88220 U L - Package GUL: VCSP50L2 E 2 Packaging and formingspecification E2: Embossed tape and reel VCSP50L2(BD882xxGUL) 1PIN MARK <Tape and Reel information> Tape Embossed carrier tape Quantity 3000pcs Direction of feed 2.100.05 E2 The direction is the 1pin of product is at the upper left when you hold ( reel on the left hand and you pull out the tape on the right hand ) S 0.06 S 14-0.250.05 0.05 AB A D (0.15) INDEX POST B C B A 1 2 3 4 (Unit : mm) 0.300.05 P=0.5X3 www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 1pin Reel 21/22 Direction of feed Order quantity needs to be multiple of the minimum quantity. 2011.03 - Rev. A BD88200GUL,BD88210GUL,BD88215GUL,BD88220GUL www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. 22/22 Technical Note 2011.03 - Rev. A Datasheet Notice Precaution on using ROHM Products 1. Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment, OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you (Note 1) , transport intend to use our Products in devices requiring extremely high reliability (such as medical equipment equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property ("Specific Applications"), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM's Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASS CLASSb CLASS CLASS CLASS CLASS 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM's Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual ambient temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification Notice - GE (c) 2014 ROHM Co., Ltd. All rights reserved. Rev.002 Datasheet Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label QR code printed on ROHM Products label is for ROHM's internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act, please consult with ROHM representative in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable for infringement of any intellectual property rights or other damages arising from use of such information or data.: 2. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the information contained in this document. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. Notice - GE (c) 2014 ROHM Co., Ltd. All rights reserved. Rev.002 Datasheet General Precaution 1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents. ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny ROHM's Products against warning, caution or note contained in this document. 2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior notice. Before purchasing or using ROHM's Products, please confirm the la test information with a ROHM sale s representative. 3. The information contained in this doc ument is provi ded on an "as is" basis and ROHM does not warrant that all information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or concerning such information. Notice - WE (c) 2014 ROHM Co., Ltd. All rights reserved. Rev.001 Datasheet bd88220gul - Web Page Buy Distribution Inventory Part Number Package Unit Quantity Minimum Package Quantity Packing Type Constitution Materials List RoHS bd88220gul VCSP50L2 3000 3000 Taping inquiry Yes