DataSheeT - enpirion(R) power solutions EN5311QI 1A PowerSoC Step-Down DC-DC Switching Converter with Integrated Inductor DESCRIPTION The Ultra-Low-Profile EN5311QI is targeted to applications where board area and profile are critical. EN5311QI is a complete power conversion solution requiring only two low cost ceramic MLCC caps. Inductor, MOSFETS, PWM, and compensation are integrated into a tiny 5mm x 4mm x 1.1mm QFN package. The EN5311QI is engineered to simplify design and to minimize layout constraints. 4 MHz switching frequency and internal type III compensation provides superior transient response. With a 1.1 mm profile, the EN5311QI is ideal for space and height constrained applications. A 3-pin VID output voltage selector provides seven pre-programmed output voltages along with an option for external resistor divider. Output voltage can be programmed on-the-fly to provide fast, dynamic voltage scaling. FEATURES * Revolutionary Integrated Inductor * 5mm x 4mm x1.1mm QFN package * Very small total solution foot print * * * * * * * * * * * * * * * 4 MHz switching frequency Only two low cost MLCC caps required Designed for low noise/low EMI Very low ripple voltage; 5mVp-p Typical High efficiency, up to 95% Wide 2.4V to 6.6V input range 1000mA continuous output current Less than 1 A standby current. Excellent transient performance 3 Pin VID Output Voltage select External divider: 0.6V to VIN-Vdropout 100% duty cycle capable Short circuit and over current protection UVLO and thermal protection RoHS compliant; MSL 3 260C reflow APPLICATIONS * * * * * * Area constrained applications Noise Sensitive Applications such as A/V and RF LDO replacement for improved thermals Set top box/home gateway Smart phones, PDAs VoIP and Video phones * Personal Media Player VIN UVLO Thermal Limit Current Limit ENABLE Soft Start P-Drive ENABLE VSENSE VIN VIN 4.7F VOLTAGE SELECT VOUT EN5311QI VS0 VS1 VS2 VOUT (-) Logic VOUT PWM Comp (+) N-Drive GND COUT VSENSE Sawtooth Generator Compensation Network VFB (-) Switch Error Amp VFB (+) GND DAC VREF Voltage Select Package Boundry VS0 VS1 VS2 Figure 1: Simplified Applications Circuit Figure 2. Featuring Integrated Inductor Technology Page 1 03799 March 1, 2019 Rev H Datasheet | Intel(R) Enpirion(R) Power Solutions: EN5311QI ORDERING INFORMATION Part Number Package Markings TJ Rating Package Description EN5311QI N5311 -40C to +125C 20-pin (5mm x 4mm x 1.1mm) QFN EVB-EN5311QI EVB-EN5311QI QFN Evaluation Board Packing and Marking Information: https://www.intel.com/support/quality-and-reliability/packing.html PIN FUNCTIONS Figure 3: Pin Diagram (Top View) NOTE A: NC pins are not to be electrically connected to each other or to any external signal, ground, or voltage. However, they must be soldered to the PCB. Failure to follow this guideline may result in part malfunction or damage. NOTE B: White `dot' on top left is pin 1 indicator on top of the device package. Page 2 03799 March 1, 2019 Rev H Datasheet | Intel(R) Enpirion(R) Power Solutions: EN5311QI PIN DESCRIPTIONS PIN NAME TYPE FUNCTION 1, 2 VIN Power Input voltage pin. Supplies power to the IC. 3 Input Ground Power Input power ground. Connect this pin to the ground terminal of the input capacitor. Refer to Layout Recommendations for further details. 4 Ground Power Power ground. The output filter capacitor should be connected between this pin and VOUT. Refer to Layout recommendations for further detail. 5- 7 VOUT Power Regulated converter output. 8- 14 NC - These pins should not be electrically connected to each other or to any external signal, voltage, or ground. One or more of these pins may be connected internally. Analog Sense pin for output voltage regulation. Connect VSENSE to the output voltage rail as close to the terminal of the output filter capacitor as possible. Analog Feedback pin for external divider option. When using the external divider option (VS0=VS1=VS2= high) connect this pin to the center of the external divider. Set the divider such that VFB = 0.603V. Analog Output voltage select. VS0=pin19, VS1=pin18, VS2=pin17. Selects one of seven preset output voltages or choose external divider by connecting pins to logic high or low. Logic low is defined as VLOW 0.4V. Logic high is defined as VHIGH 1.4V. Any level between these two values is indeterminate. Analog Output enable. Enable = logic high, disable = logic low. Logic low is defined as VLOW 0.2V. Logic high is defined as VHIGH 1.4V. Any level between these two values is indeterminate. Power Device thermal pad to remove heat from package. Connect to PCB surface ground pad and PCB internal ground plane (see layout recommendations). 15 16 17-19 20 VSENSE VFB VS0, VS1, VS2 ENABLE Bottom Thermal Pad ABSOLUTE MAXIMUM RATINGS CAUTION: Absolute Maximum ratings are stress ratings only. Functional operation beyond the recommended operating conditions is not implied. Stress beyond the absolute maximum ratings may impair device life. Exposure to absolute maximum rated conditions for extended periods may affect device reliability. Absolute Maximum Pin Ratings PARAMETER SYMBOL MIN MAX UNITS Input Supply Voltage -0.3 7.0 V ENABLE, VSENSE, VS0- VS2 -0.3 VIN+0.3 V VFB -0.3 2.7 V Page 3 03799 March 1, 2019 Rev H Datasheet | Intel(R) Enpirion(R) Power Solutions: EN5311QI Absolute Maximum Thermal Ratings PARAMETER CONDITION MIN Maximum Operating Junction Temperature Storage Temperature Range Reflow Peak Body Temperature -65 (10 Sec) MSL3 JEDEC J-STD020A MAX UNITS +150 C +150 C +260 C MAX UNITS Absolute Maximum ESD Ratings PARAMETER CONDITION MIN HBM (Human Body Model) 2000 V RECOMMENDED OPERATING CONDITIONS PARAMETER SYMBOL MIN MAX UNITS Input Voltage Range VIN 2.4 5.5 V Input Voltage Range (External Divider (VFB)) (1) VIN 2.4 6.6 V Output Voltage Range VOUT 0.6 VIN - 0.6 V Output Current Range IOUT 0 1000 mA Operating Ambient Temperature Range TA -40 +85 C Operating Junction Temperature TJ -40 +125 C THERMAL CHARACTERISTICS PARAMETER SYMBOL TYPICAL UNITS TSD 150 C TSDHYS 15 C Thermal Resistance: Junction to Ambient (0 LFM) (2) JA 65 C/W Thermal Resistance: Junction to Case (0 LFM) JC 15 C/W Thermal Shutdown Thermal Shutdown Hysteresis Page 4 03799 March 1, 2019 Rev H Datasheet | Intel(R) Enpirion(R) Power Solutions: EN5311QI ELECTRICAL CHARACTERISTICS NOTE: TA = 25C unless otherwise noted. Typical values are at VIN = 3.6V, CIN = 4.7F, COUT=10F. NOTE: VIN must be greater than VOUT + 0.6V. PARAMETER Operating Input Voltage Under Voltage Lock-out SYMBOL VIN VUVLO TEST CONDITIONS MIN Using VID Using External Divider (VFB) (1) TYP MAX UNITS 2.4 5.5 V 2.4 6.6 V 2.3 V 2.2 VIN going low to high UVLO Hysteresis 0.145 VOUT Initial Accuracy (VID) VOUT VOUT Variation for all Causes (VID) VOUT Feedback Pin Voltage VFB 2.4V VIN 5.5V, ILOAD = 1A; TA = 25C 2.4V VIN 5.5V, ILOAD = 0- 1A, TA = -40C to +85C 2.4V VIN 6.6V, ILOAD = 1A TA = 25C; VSO=VS1=VS2=1 V -2.0 +2.0 % -3.0 +3.0 % 0.591 0.603 0.615 0.585 0.603 0.621 2.4V VIN 6.6V, ILOAD = 0 -1A, Feedback Pin Voltage VFB TA = -40C to +85C; V V VSO=VS1=VS2=1 Feedback Pin Input Current 1 IFB Dynamic Voltage Slew Rate (3) Vslew 1.24 Output Current IOUT 1000 Shut-Down Current ISD Quiescent Current PFET OCP Threshold ILIM VS0-VS1 Thresholds VTH VS0-VS2 Pin Input Current IVSX 1.65 nA 2.1 V/ms mA Enable = Low 0.75 A No switching 800 A 2 A 2.4V VIN 6.6V, 0.6V VOUT VIN - 0.6V 1.4 Pin = Low 0.0 0.4 Pin = High 1.4 VIN 1 nA Page 5 03799 March 1, 2019 Rev H Datasheet | Intel(R) Enpirion(R) Power Solutions: EN5311QI PARAMETER SYMBOL Enable Voltage Threshold Enable Pin Input Current IEN TEST CONDITIONS MIN Logic Low 0.0 0.2 Logic High 1.4 VIN VIN = 3.6V TYP MAX UNITS 2 A Operating Frequency FOSC 4 MHz PFET On Resistance RDS(ON) 340 m NFET On Resistance RDS(ON) 270 m 0.110 Typical inductor DCR VOUT Soft Start Slew Rate(3) VSS VID Mode (4) 1.24 1.65 2.1 V/ms Soft Start Rise Time TSS VFB mode (4) 0.80 1.10 1.40 ms (1) See Section "Application Information" for specific circuit requirements. (2) Based on 2oz. external copper layers and proper thermal design in line with EIJ/JEDEC JESD51-7 standard for high thermal conductivity boards. (3) Parameter not production tested but is guaranteed by design. (4) Measured from when VIN VUVLO & ENABLE pin crosses its logic High threshold. Page 6 03799 March 1, 2019 Rev H Datasheet | Intel(R) Enpirion(R) Power Solutions: EN5311QI TYPICAL PERFORMANCE CURVES Efficiency Vs. Load Current (Vin = 3.3V) 95 100 90 95 85 90 Efficency (%) Efficency (%) Efficiency Vs. Load Current (Vin = 5.0V) 80 75 70 65 60 55 85 80 75 70 65 60 55 50 50 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 Load Current (A) 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 Load Current (A) Top to Bottom: VOUT = 3.3V, 2.5V, 1.8V, 1.5V, 1.2V, 0.8V Top to Bottom: VOUT = 2.5V, 1.8V, 1.5V, 1.2V, 0.8V Page 7 03799 March 1, 2019 Rev H Datasheet | Intel(R) Enpirion(R) Power Solutions: EN5311QI TYPICAL PERFORMANCE CHARACTERISTICS Output Ripple: VIN = 5.0V, VOUT = 1.2V, ILOAD = 1A, COUT = 1 x 10F 0805 Output Ripple: VIN = 3.3V, VOUT = 1.2V, ILOAD = 1A, COUT = 1 x 10F 0805 Page 8 03799 March 1, 2019 Rev H Datasheet | Intel(R) Enpirion(R) Power Solutions: EN5311QI FUNCTIONAL BLOCK DIAGRAM VIN UVLO Thermal Limit Current Limit ENABLE Soft Start P-Drive (-) Logic VOUT PWM Comp (+) N-Drive GND VSENSE Sawtooth Generator Compensation Network (-) Switch Error Amp VFB (+) DAC VREF Voltage Select Package Boundry VS0 VS1 VS2 Figure 4: Functional Block Diagram Page 9 03799 March 1, 2019 Rev H Datasheet | Intel(R) Enpirion(R) Power Solutions: EN5311QI FUNCTIONAL DESCRIPTION Synchronous DC-DC Step-Down PowerSoC The EN5311QI is a complete DC-DC converter solution requiring only two low cost MLCC capacitors. MOSFET switches, PWM controller, Gate-drive, compensation, and inductor are integrated into the tiny 5mm x 4mm x 1.1mm package to provide the smallest footprint possible while maintaining high efficiency, low ripple, and high performance. The converter uses voltage mode control to provide the simplest implementation and high noise immunity. The device operates at a high switching frequency. The high switching frequency allows for a wide control loop bandwidth providing excellent transient performance. The high switching frequency enables the use of very small components making possible this unprecedented level of integration. Intel Enpirion's proprietary power MOSFET technology provides very low switching loss at frequencies of 4 MHz and higher, allowing for the use of very small internal components, and very wide control loop bandwidth. Unique magnetic design allows for integration of the inductor into the very low profile 1.1mm package. Integration of the inductor virtually eliminates the design/layout issues normally associated with switch-mode DCDC converters. All of this enables much easier and faster integration into various applications to meet demanding EMI requirements. Output voltage is chosen from seven preset values via a three pin VID voltage select scheme. An external divider option enables the selection of any voltage in the 0.6V to VIN-0.6V range. This reduces the number of components that must be qualified and reduces inventory burden. The VID pins can be toggled on the fly to implement glitch free dynamic voltage scaling. Protection features include under-voltage lock-out (UVLO), over-current protection (OCP), short circuit protection, and thermal overload protection. Integrated Inductor Intel Epirion has introduced the world's first product family featuring integrated inductors. The use of an internal inductor localizes the noises associated with the output loop currents. The inherent shielding and compact construction of the integrated inductor reduces the radiated noise that couples into the traces of the circuit board. Further, the package layout is optimized to reduce the electrical path length for the AC ripple currents that are a major source of radiated emissions from DCDC converters. The integrated inductor significantly reduces parasitic effects that can harm loop stability, and makes layout very simple. Soft Start Internal soft start circuits limit in-rush current when the device starts up from a power down condition or when the "ENABLE" pin is asserted "high". Digital control circuitry limits the VOUT ramp rate to levels that are safe for the Power MOSFETS and the integrated inductor. The EN5311QI operates in a constant slew rate when the output voltage is programmed with an internal VID code. The EN5311QI, when in external resistor divider mode, has a constant start up time. Please refer to the Electrical Characteristics table for soft-start slew rates and soft-start time Excess bulk capacitance on the output of the device can cause an over-current condition at startup. Assuming no-load at startup, the maximum total capacitance on the output, including the output filter capacitor, bulk and decoupling capacitance, at the load, is given as: Page 10 03799 March 1, 2019 Rev H Datasheet | Intel(R) Enpirion(R) Power Solutions: EN5311QI In VID Mode: COUT_TOTAL_MAX = COUT_Filter + COUT_BULK = 700F In external divider mode: COUT_TOTAL_MAX = 1.22x10-3/VOUT Farads See the applications section for more details. Startup into Pre-Bias The EN5311QI supports startup into a pre-biased output of up to VOUT. The output of the EN5311QI can be pre-biased with a voltage up to VOUT when it is first enabled. Over Current/Short Circuit Protection The current limit function is achieved by sensing the current flowing through a sense P-MOSFET which is compared to a reference current. When this level is exceeded the P-FET is turned off and the N-FET is turned on, pulling VOUT low. This condition is maintained for a period of 1ms and then a normal soft start is initiated. If the over current condition still persists, this cycle will repeat in a "hick-up" mode. Under Voltage Lockout During initial power up an under voltage lockout circuit will hold-off the switching circuitry until the input voltage reaches a sufficient level to insure proper operation. If the voltage drops below the UVLO threshold the lockout circuitry will again disable the switching. Hysteresis is included to prevent chattering between states. Enable The ENABLE pin provides a means to shut down the converter or enable normal operation. A logic low will disable the converter and cause it to shut down. A logic high will enable the converter into normal operation. In shutdown mode, the device quiescent current will be less than 1 A. NOTE: This pin must not be left floating. Thermal Shutdown When excessive power is dissipated in the chip, the junction temperature rises. Once the junction temperature exceeds the thermal shutdown temperature the thermal shutdown circuit turns off the converter output voltage thus allowing the device to cool. When the junction temperature decreases by 15C, the device will go through the normal startup process. Page 11 03799 March 1, 2019 Rev H Datasheet | Intel(R) Enpirion(R) Power Solutions: EN5311QI APPLICATION INFORMATION Output Voltage Setting To provide the highest degree of flexibility in choosing output voltage, the EN5311QI uses a 3 pin VID, or Voltage ID, output voltage select arrangement. This allows the designer to choose one of seven preset voltages, or to use an external voltage divider. Internally, the output of the VID multiplexer sets the value for the voltage reference DAC, which in turn is connected to the non-inverting input of the error amplifier. This allows the use of a single feedback divider with constant loop gain and optimum compensation, independent of the output voltage selected. Since VFB is a sensitive node, do not touch the VFB node while the device is in operation as doing so may introduce parasitic capacitance into the control loop that causes the device to behave abnormally and damage may occur. Table 1 shows the various VS0-VS2 pin logic states and the associated output voltage levels. A logic "1" indicates a connection to VIN or to a "high" logic voltage level. A logic "0" indicates a connection to ground or to a "low" logic voltage level. These pins can be either hardwired to VIN or GND or alternatively can be driven by standard logic levels. Logic low is defined as VLOW 0.4V. Logic high is defined as VHIGH 1.4V. Any level between these two values is indeterminate. These pins must not be left floating. The External Voltage Divider pin, VFB, may be left floating for all VID settings other than the VS0=VS1=VS2= "1". Table 1: VID Voltage Select Settings VS2 VS1 VS0 VOUT 0 0 0 3.3V 0 0 1 2.5V 0 1 0 1.8V 0 1 1 1.5V 1 0 0 1.25V 1 0 1 1.2V 1 1 0 0.8V 1 1 1 User Selectable Page 12 03799 March 1, 2019 Rev H Datasheet | Intel(R) Enpirion(R) Power Solutions: EN5311QI External Voltage Divider As described above, the external voltage divider option is chosen by connecting the VS0, VS1, and VS2 pins to VIN or logic "high". The EN5311QI uses a separate feedback pin, VFB, when using the external divider. For applications with VIN 5.5V, VSENSE must be connected to VOUT as indicated in Figure 5. Figure 6 indicates the required connections for VIN > 5.5V. VSense ENABLE EN5311QI VIN Vin 4.7uF VS0 VS1 VS2 VOUT Vout COUT Ra VFB Rb GND Figure 5. External Divider (VIN 5.5V) The output voltage is selected by the following formula: VOUT = 0.603V (1 + Ra Rb ) Ra must be chosen as 200K to maintain loop gain. Then Rb is given as: Rb = 1.2 x10 5 VOUT - 0.603 VOUT can be programmed over the range of 0.6V to VIN - 0.6V (0.6 is the nominal full load dropout voltage including margin). VSense ENABLE Vin 4.7uF VS0 VS1 VS2 EN5311QI VIN VOUT Vout Ca Ra 27pF COUT VFB Rb GND Figure 6. External Divider (VIN > 5.5V) For applications where VIN > 5.5V, the VSENSE connection is not necessary, but the addition of CA = 27pF is required. Page 13 03799 March 1, 2019 Rev H Datasheet | Intel(R) Enpirion(R) Power Solutions: EN5311QI Dynamically Adjustable Output The EN5311QI is designed to allow for dynamic switching between the predefined VID voltage levels. The inter-voltage slew rate is optimized to prevent excess undershoot or overshoot as the output voltage levels transition. The slew rate is identical to the soft-start slew rate of 1.65V/ms. Dynamic transitioning between internal VID settings and the external divider is not allowed. Input and Output Capacitors The input capacitance requirement is 4.7F. Intel Enpirion recommends that a low ESR MLCC capacitor be used. The input capacitor must use a X5R or X7R or equivalent dielectric formulation. Y5V or equivalent dielectric formulations lose capacitance with frequency, bias, and with temperature, and are not suitable for switch-mode DC-DC converter input and output filter applications. The output capacitance minimum requirement depends on the output voltage setting. The following table shows the recommended minimum output capacitance for a given output voltage. Table 2. Recommended Output Capacitance VOUT COUT Size (EIA) 1V 10 F 0805 1.8V 10 F 0805 3.3V 47 F 0805 The control loop is designed to be stable with up to 60F of total output capacitance next to the output pins of the device without requiring modification to the compensation network. VOUT has to be sensed at the last output filter capacitor next to the device. Intel Enpirion recommends a low ESR MLCC type capacitor be used. Additional capacitance may be added to improve load transient response. Additional bulk capacitance for decoupling and bypass can be placed at the load as long as there is sufficient separation between the VOUT Sense point and the bulk capacitance. The separation provides an inductance that isolates the control loop from the bulk capacitance. Excess total capacitance on the output (Output Filter + Bulk) can cause an over-current condition at startup. Refer to the section on Soft-Start for the maximum total capacitance on the output. The output capacitor must use a X5R or X7R or equivalent dielectric formulation. Y5V or equivalent dielectric formulations lose capacitance with frequency, bias, and temperature and are not suitable for switch-mode DCDC converter input and output filter applications. Table 3. Input Capacitor Recommendations Description 4.7F, 10V, X5R, 0805 10F, 10V, X5R, 0805 MFG P/N Taiyo Yuden LMK107BJ475KA-T Murata GRM185R61A475KE11# Taiyo Yuden LMK212ABJ106KG Murata GRM21BR61A106KE19 Page 14 03799 March 1, 2019 Rev H Datasheet | Intel(R) Enpirion(R) Power Solutions: EN5311QI Table 4. Output Capacitor Recommendations Description MFG P/N 10F, 10V, Taiyo Yuden LMK212ABJ106KG X5R, 0805 Murata GRM21BR61A106KE19 22F, 10V, Taiyo Yuden LMK212BBJ226MG-T X5R, 0805 Murata GRM21BR61A226ME51 47F, 6.3V, Taiyo Yuden JMK212BBJ476MG-T X5R, 0805 Murata GRM21BR60J476ME15 Power-Up Sequencing During power-up, ENABLE should not be asserted before VIN. Tying these pins together meets these requirements. Page 15 03799 March 1, 2019 Rev H Datasheet | Intel(R) Enpirion(R) Power Solutions: EN5311QI LAYOUT RECOMMENDATIONS *Optimized PCB Layout file downloadable from the Intel Enpirion Website to assure first pass design success. Recommendation 1: Input and output filter capacitors should be placed on the same side of the PCB, and as close to the EN5311QI package as possible. They should be connected to the device with very short and wide traces. Do not use thermal reliefs or spokes when connecting the capacitor pads to the respective nodes. The +V and GND traces between the capacitors and the EN5311QI should be as close to each other as possible so that the gap between the two nodes is minimized, even under the capacitors. Recommendation 2: DO NOT connect GND pins 3 and 4 together. Pin 3 should be used for the Input capacitor local ground and pin 4 should be used for the output capacitor ground. The ground pad for the input and output filter capacitors should be isolated ground islands and should be connected to system ground as indicated in recommendation 3 and recommendation 5. Recommendation 3: Multiple small vias (0.25mm after copper plating) should be used to connect ground terminals of the Input capacitor and the output capacitor to the system ground plane. This provides a low inductance path for the high-frequency AC currents; thereby reducing ripple and suppressing EMI (see Fig. 7, Fig. 8, and Fig. 9). Recommendation 4: The large thermal pad underneath the component must be connected to the system ground plane through as many thermal vias as possible. The vias should use 0.33mm drill size with minimum one ounce copper plating (0.035mm plating thickness). This provides the path for heat dissipation from the converter. Recommendation 5: The system ground plane referred to in recommendations 3 and 4 should be the first layer immediately below the surface layer (PCB layer 2). This ground plane should be continuous and uninterrupted below the converter and the input and output capacitors that carry large AC currents. If it is not possible to make PCB layer 2 a continuous ground plane, an uninterrupted ground "island" should be created on PCB layer 2 immediately underneath the EN5311QI and its input and output capacitors. The vias that connect the input and output capacitor grounds, and the thermal pad to the ground island, should continue through to the PCB GND layer as well. Recommendation 6: As with any switch-mode DC-DC converter, do not run sensitive signal or control lines underneath the converter package. Recommendation 7: The VOUT sense point should be just after the last output filter capacitor next to the device. Keep the sense trace short in order to avoid noise coupling into the node. Recommendation 8: Keep Ra, Ca, and Rb close to the VFB pin (see Figures 4 and 5). The VFB pin is a highimpedance, sensitive node. Keep the trace to this pin as short as possible. Whenever possible, connect Rb directly to the GND pin instead of going through the GND plane. Figure 6 shows an example schematic for the EN5311QI using the internal voltage select. In this example, the device is set to a VOUT of 1.5V (VS2=0, VS1=1, VS0=1). Figure 7 shows an example schematic using an external voltage divider. VS0=VS1=VS2= "1". The resistor values are chosen to give an output voltage of 2.6V. Page 16 03799 March 1, 2019 Rev H VFB VSENSE NC NC NC NC 14 13 12 11 19 8 NC 20 7 4.7uF VOUT Rb=60K Ra=200K 6 VOUT VOUT 5 VS0 ENABLE 4 NC 3 9 GND NC VS1 GND 6 VOUT Figure 7. Example application, Vout=1.5V. 15 NC 11 5 VOUT 10F VIN 16 NC 12 4.7uF (see layout recommendation 3) VOUT 10 18 1 NC 13 VIN 17 2 NC 14 VOUT 4 NC 7 3 8 20 GND 19 GND VS0 ENABLE VS2 VIN VFB VSENSE 15 NC 2 9 1 NC VS1 VIN 10 18 VIN 17 VIN VS2 16 Datasheet | Intel(R) Enpirion(R) Power Solutions: EN5311QI VOUT 10F (see layout recommendation 3) Figure 8. Example Application, external divider, Vout = 2.6V. Figure 9 shows an example board layout. The left side of the figure demonstrates construction of the PCB top layer. Note the placement of the vias from the input and output filter capacitor grounds, and the thermal pad, to the PCB ground on layer 2 (1st layer below PCB surface). The right side of the figure shows the layout with the components populated. Note the placement of the vias per recommendation 3. Figure 9. Example layout showing PCB top layer, as well as demonstrating use of vias from input, output filter capacitor local grounds, and thermal pad, to PCB system ground. Page 17 03799 March 1, 2019 Rev H Datasheet | Intel(R) Enpirion(R) Power Solutions: EN5311QI DESIGN CONSIDERATIONS FOR LEAD-FRAME BASED MODULES Exposed Metal on Bottom of Package Intel has developed a break-through in package technology that utilizes the lead frame as part of the electrical circuit. The lead frame offers many advantages in thermal performance, in reduced electrical lead resistance, and in overall foot print. However, it does require some special considerations. As part of the package assembly process, lead frame construction requires that for mechanical support, some of the lead-frame cantilevers be exposed at the point where wire-bond or internal passives are attached. This results in several small pads being exposed on the bottom of the package. Only the large thermal pad and the perimeter pin pads are to be mechanically or electrically connected to the PC board. The PCB top layer under the EN5311QI should be clear of any metal except for the large thermal pad. The "grayed-out" area in Figure 10 represents the area that should be clear of any metal (traces, vias, or planes), on the top layer of the PCB. NOTE: Clearance between the various exposed metal pads, the thermal ground pad, and the perimeter pins, meets or exceeds JEDEC requirements for lead frame package construction (JEDEC MO-220, Issue J, Date May 2005). The separation between the large thermal pad and the nearest adjacent metal pad or pin is a minimum of 0.20mm, including tolerances. This is shown in Figure 11. Thermal Pad. Connect to Ground plane Figure 10. Exposed metal and mechanical dimensions of the package. Gray area represents bottom metal noconnect and area that should be clear of any traces, planes, or vias, on the top layer of the PCB. Page 18 03799 March 1, 2019 Rev H Datasheet | Intel(R) Enpirion(R) Power Solutions: EN5311QI Figure 11. Exposed pad clearances; the Intel Enpirion lead frame package complies with JEDEC requirements. Page 19 03799 March 1, 2019 Rev H Datasheet | Intel(R) Enpirion(R) Power Solutions: EN5311QI Figure 12. Recommended solder mask opening Page 20 03799 March 1, 2019 Rev H Datasheet | Intel(R) Enpirion(R) Power Solutions: EN5311QI Figure 13. Package mechanical dimensions. Page 21 03799 March 1, 2019 Rev H Datasheet | Intel(R) Enpirion(R) Power Solutions: EN5311QI REVISION HISTORY Rev H Date Jan. 2019 Change(s) * Changed datasheet into Intel format. WHERE TO GET MORE INFORMATION For more information about Intel(R) and Enpirion(R) PowerSoCs, visit: www.Intel.com/enpirion (c) 2017 Intel Corporation. All rights reserved. Intel, the Intel logo, Altera, ARRIA, CYCLONE, ENPIRION, MAX, MEGACORE, NIOS, QUARTUS, and STRATIX words and logos are trademarks of Intel Corporation or its subsidiaries in the U.S. and/or other countries. Other marks and brands may be claimed as the property of others. Intel reserves the right to make changes to any products and services at any time without notice. Intel assumes no responsibility or liability arising out of the application or use of any information, product, or service described herein except as expressly agreed to in writing by Intel. Intel customers are advised to obtain the latest version of device specifications before relying on any published information and before placing orders for products or services. * Other marks and brands may be claimed as the property of others. Page 22 03799 March 1, 2019 Rev H