Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com Please note: As part of the Fairchild Semiconductor integration, some of the Fairchild orderable part numbers will need to change in order to meet ON Semiconductor's system requirements. Since the ON Semiconductor product management systems do not have the ability to manage part nomenclature that utilizes an underscore (_), the underscore (_) in the Fairchild part numbers will be changed to a dash (-). This document may contain device numbers with an underscore (_). Please check the ON Semiconductor website to verify the updated device numbers. The most current and up-to-date ordering information can be found at www.onsemi.com. Please email any questions regarding the system integration to Fairchild_questions@onsemi.com. ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. "Typical" parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. FSB50825A / FSB50825AT Motion SPM(R) 5 Series Features Related Source * UL Certified No. E209204 (UL1557) * RD-FSB50450A - Reference Design for Motion SPM 5 Series Ver.2 * 250 V RDS(on) = 0.45 Max FRFET MOSFET 3Phase Inverter with Gate Drivers and Protection * AN-9082 - Motion SPM5 Series Thermal Performance by Contact Pressure * Built-in Bootstrap Diodes Simplify PCB Layout * AN-9080 - User's Guide for Motion SPM 5 Series V2 * Separate Open-Source Pins from Low-Side MOSFETs for Three-Phase Current-Sensing General Description * Active-HIGH Interface, Works with 3.3 / 5 V Logic, Schmitt-trigger Input The FSB50825A/AT is an advanced Motion SPM(R) 5 module providing a fully-featured, high-performance inverter output stage for AC Induction, BLDC and PMSM motors. These modules integrate optimized gate drive of the built-in MOSFETs(FRFET(R) technology) to minimize EMI and losses, while also providing multiple on-module protection features including under-voltage lockouts and thermal monitoring. The built-in high-speed HVIC requires only a single supply voltage and translates the incoming logic-level gate inputs to the high-voltage, high-current drive signals required to properly drive the module's internal MOSFETs. Separate open-source MOSFET terminals are available for each phase to support the widest variety of control algorithms. * Optimized for Low Electromagnetic Interference * HVIC Temperature-Sensing Built-in for Temperature Monitoring * HVIC for Gate Driving and Under-Voltage Protection * Isolation Rating: 1500 Vrms / 1 min. * RoHS Compliant Applications * 3-Phase Inverter Driver for Small Power AC Motor Drives FSB50825A FSB50325A FSB50825AT FSB50325AT Package Marking & Ordering Information Device Marking Device Package Reel Size Packing Type Quantity FSB50825A FSB50825A SPM5P-023 - Rail 15 FSB50825AT FSB50825AT SPM5N-023 - Rail 15 (c)2012 Fairchild Semiconductor Corporation FSB50825A / FSB50825AT Rev. 1.2 1 www.fairchildsemi.com FSB50825A / FSB50825AT Motion SPM(R) 5 Series October 2016 Inverter Part (each MOSFET unless otherwise specified.) Symbol Parameter Conditions Rating Unit VDSS Drain-Source Voltage of Each MOSFET 250 V *ID 25 Each MOSFET Drain Current, Continuous TC = 25C 3.6 A *ID 80 Each MOSFET Drain Current, Continuous TC = 80C 2.7 A *IDP Each MOSFET Drain Current, Peak TC = 25C, PW < 100 s 9.0 A *IDRMS Each MOSFET Drain Current, Rms TC = 80C, FPWM < 20 kHz 1.9 Arms Maximum Power Dissipation TC = 25C, For Each MOSFET 14.2 W Rating Unit *PD Control Part (each HVIC unless otherwise specified.) Symbol Parameter Conditions VCC Control Supply Voltage Applied Between VCC and COM 20 V VBS High-side Bias Voltage Applied Between VB and VS 20 V VIN Input Signal Voltage Applied Between IN and COM -0.3 ~ VCC + 0.3 V Rating Unit 250 V Bootstrap Diode Part (each bootstrap diode unless otherwise specified.) Symbol VRRMB Parameter Conditions Maximum Repetitive Reverse Voltage * IFB Forward Current TC = 25C 0.5 A * IFPB Forward Current (Peak) TC = 25C, Under 1ms Pulse Width 1.5 A Conditions Rating Unit Each MOSFET under Inverter Operating Condition (1st Note 1) 8.8 C/W Thermal Resistance Symbol RJC Parameter Junction to Case Thermal Resistance Total System Symbol Rating Unit Operating Junction Temperature -40 ~ 150 C TSTG Storage Temperature -40 ~ 125 C VISO Isolation Voltage 1500 Vrms TJ Parameter Conditions 60 Hz, Sinusoidal, 1 Minute, Connect Pins to Heat Sink Plate 1st Notes: 1. For the measurement point of case temperature TC, please refer to Figure 4. 2. Marking " * " is calculation value or design factor. (c)2012 Fairchild Semiconductor Corporation FSB50825A / FSB50825AT Rev. 1.2 2 www.fairchildsemi.com FSB50825A / FSB50825AT Motion SPM(R) 5 Series Absolute Maximum Ratings FSB50825A / FSB50825AT Motion SPM(R) 5 Series Pin descriptions Pin Number Pin Name Pin Description 1 COM IC Common Supply Ground 2 VB(U) Bias Voltage for U-Phase High-Side MOSFET Driving 3 VCC(U) Bias Voltage for U-Phase IC and Low-Side MOSFET Driving 4 IN(UH) Signal Input for U-Phase High-Side 5 IN(UL) Signal Input for U-Phase Low-Side 6 N.C No Connection 7 VB(V) Bias Voltage for V-Phase High Side MOSFET Driving 8 VCC(V) Bias Voltage for V-Phase IC and Low Side MOSFET Driving 9 IN(VH) Signal Input for V-Phase High-Side 10 IN(VL) Signal Input for V-Phase Low-Side Output for HVIC Temperature Sensing 11 VTS 12 VB(W) 13 VCC(W) Bias Voltage for W-Phase IC and Low-Side MOSFET Driving 14 IN(WH) Signal Input for W-Phase High-Side 15 IN(WL) Signal Input for W-Phase Low-Side 16 N.C Bias Voltage for W-Phase High-Side MOSFET Driving No Connection 17 P 18 U, VS(U) Positive DC-Link Input 19 NU Negative DC-Link Input for U-Phase 20 NV Negative DC-Link Input for V-Phase 21 V, VS(V) 22 NW 23 W, VS(W) Output for U-Phase & Bias Voltage Ground for High-Side MOSFET Driving Output for V-Phase & Bias Voltage Ground for High-Side MOSFET Driving Negative DC-Link Input for W-Phase Output for W Phase & Bias Voltage Ground for High-Side MOSFET Driving (1) COM (2) VB(U) (17) P (3) V CC(U) VCC VB (4) IN (UH) HIN HO (5) IN (UL) LIN VS COM LO (18) U, V S(U) (6) N.C (19) N U (7) VB(V) (8) V CC(V) VCC VB (9) IN (VH) HIN HO (10) IN (VL) LIN VS COM LO (11) V TS (20) N V (21) V, V S(V) V TS (12) V B(W) (13) V CC(W) VCC VB (14) IN (WH) HIN HO LIN VS COM LO (15) IN (WL) (22) N W (23) W, V S(W) (16) N.C Figure 1. Pin Configuration and Internal Block Diagram (Bottom View) 1st Notes: 3. Source terminal of each low-side MOSFET is not connected to supply ground or bias voltage ground inside Motion SPM(R) 5 product. External connections should be made as indicated in Figure 3. (c)2012 Fairchild Semiconductor Corporation FSB50825A / FSB50825AT Rev. 1.2 3 www.fairchildsemi.com Inverter Part (each MOSFET unless otherwise specified.) Symbol Parameter Conditions BVDSS Drain - Source Breakdown Voltage VIN = 0 V, ID = 1 mA (2nd Note 1) IDSS Zero Gate Voltage Drain Current RDS(on) VSD - - V VIN = 0 V, VDS = 250 V - - 1 mA Static Drain - Source Turn-On Resistance VCC = VBS = 15 V, VIN = 5 V, ID = 2.0 A - 0.33 0.45 Drain - Source Diode Forward Voltage VCC = VBS = 15V, VIN = 0 V, ID = -2.0 A - - 1.2 V - 950 - ns - 520 - ns Switching Times VPN = 150 V, VCC = VBS = 15 V, ID = 2.0 A VIN = 0 V 5 V, Inductive Load L = 3 mH High- and Low-Side MOSFET Switching (2nd Note 2) - 150 - ns - 100 - J - 10 - J tON EON EOFF RBSOA Unit 250 tOFF trr Min Typ Max V = 200 V, VCC = VBS = 15 V, ID = IDP, VDS = BVDSS, Reverse Bias Safe Oper- PN TJ = 150C ating Area High- and Low-Side MOSFET Switching (2nd Note 3) Full Square Control Part (each HVIC unless otherwise specified.) Symbol Parameter Conditions IQCC Quiescent VCC Current VCC = 15 V, VIN = 0 V IQBS Quiescent VBS Current VBS = 15 V, VIN = 0 V UVCCD UVCCR UVBSD UVBSR Min Typ Max Unit Applied Between VCC and COM - - 200 A Applied Between VB(U) - U, VB(V) - V, VB(W) - W - - 100 A 7.4 8.0 9.4 V Low-Side Under-Voltage Protection (Figure 8) VCC Under-Voltage Protection Detection Level VCC Under-Voltage Protection Reset Level 8.0 8.9 9.8 V High-Side Under-Voltage Protection (Figure 9) VBS Under-Voltage Protection Detection Level 7.4 8.0 9.4 V VBS Under-Voltage Protection Reset Level 8.0 8.9 9.8 V 600 790 980 mV - - 2.9 V 0.8 - - V VTS HVIC Temperature Sensing Voltage Output VCC = 15 V, THVIC = 25C (2nd Note 4) VIH ON Threshold Voltage Logic HIGH Level VIL OFF Threshold Voltage Logic LOW Level Applied between IN and COM Bootstrap Diode Part (each bootstrap diode unless otherwise specified.) Symbol Parameter Conditions Min Typ Max Unit VFB Forward Voltage IF = 0.1 A, TC = 25C (2nd Note 5) - 2.5 - V trrB Reverse Recovery Time IF = 0.1 A, TC = 25C - 80 - ns 2nd Notes: 1. BVDSS is the absolute maximum voltage rating between drain and source terminal of each MOSFET inside Motion SPM(R) 5 product. VPN should be sufficiently less than this value considering the effect of the stray inductance so that VPN should not exceed BVDSS in any case. 2. tON and tOFF include the propagation delay of the internal drive IC. Listed values are measured at the laboratory test condition, and they can be different according to the field applications due to the effect of different printed circuit boards and wirings. Please see Figure 6 for the switching time definition with the switching test circuit of Figure 7. 3. The peak current and voltage of each MOSFET during the switching operation should be included in the Safe Operating Area (SOA). Please see Figure 7 for the RBSOA test circuit that is same as the switching test circuit. 4. Vts is only for sensing-temperature of module and cannot shutdown MOSFETs automatically. 5. Built-in bootstrap diode includes around 15 resistance characteristic. Please refer to Figure 2. (c)2012 Fairchild Semiconductor Corporation FSB50825A / FSB50825AT Rev. 1.2 4 www.fairchildsemi.com FSB50825A / FSB50825AT Motion SPM(R) 5 Series Electrical Characteristics (TJ = 25C, VCC = VBS = 15 V unless otherwise specified.) Symbol Parameter Conditions Min. Typ. Max. Unit - 150 200 V VPN Supply Voltage Applied Between P and N VCC Control Supply Voltage Applied Between VCC and COM 13.5 15.0 16.5 V VBS High-Side Bias Voltage Applied Between VB and VS 13.5 15.0 16.5 V 3.0 - VCC V 0 - 0.6 V 1.0 - - s - 15 - kHz VIN(ON) Input ON Threshold Voltage VIN(OFF) Input OFF Threshold Voltage Applied Between IN and COM tdead Blanking Time for Preventing VCC = VBS = 13.5 ~ 16.5 V, TJ 150C Arm-Short fPWM PWM Switching Frequency TJ 150C Built-in Bootstrap Diode VF-IF Characteristic 1.0 0.9 0.8 0.7 IF [A] 0.6 0.5 0.4 0.3 0.2 0.1 0.0 0 1 2 3 4 5 6 7 8 VF [V] 9 10 11 12 13 14 15 Tc=25C Figure 2. Built-in Bootstrap Diode Characteristics (Typical) (c)2012 Fairchild Semiconductor Corporation FSB50825A / FSB50825AT Rev. 1.2 5 www.fairchildsemi.com FSB50825A / FSB50825AT Motion SPM(R) 5 Series Recommended Operating Condition C1 +15 V * Example Circuit : V phase VDC P MCU R5 C5 VCC VB HIN HO LIN VS COM LO V 10 F C2 C4 LIN Output Note 0 0 Z Both FRFET Off 0 1 0 Low side FRFET On C3 1 0 VDC High side FRFET On 1 1 Forbidden Shoot through Open Open Z Same as (0,0) R3 N VTS HIN Inverter Output (R) One Leg Diagram of Motion SPM 5 Product * Example of Bootstrap Paramters : C1 = C2 = 1 F Ceramic Capacitor Figure 3. Recommended MCU Interface and Bootstrap Circuit with Parameters 3rd Notes: 1. Parameters for bootstrap circuit elements are dependent on PWM algorithm. For 15 kHz of switching frequency, typical example of parameters is shown above. 2. RC-coupling (R5 and C5) and C4 at each input of Motion SPM 5 product and MCU (Indicated as Dotted Lines) may be used to prevent improper signal due to surge-noise. 3. Bold lines should be short and thick in PCB pattern to have small stray inductance of circuit, which results in the reduction of surge-voltage. Bypass capacitors such as C1, C2 and C3 should have good high-frequency characteristics to absorb high-frequency ripple-current. Figure 4. Case Temperature Measurement 3rd Notes: 4. Attach the thermocouple on top of the heat-sink of SPM 5 package (between SPM 5 package and heatsink if applied) to get the correct temperature measurement. 3.5 3.0 VTS [V] 2.5 2.0 1.5 1.0 0.5 20 40 60 80 100 120 140 160 o THVIC [ C] Figure 5. Temperature Profile of V TS (Typical) (c)2012 Fairchild Semiconductor Corporation FSB50825A / FSB50825AT Rev. 1.2 6 www.fairchildsemi.com FSB50825A / FSB50825AT Motion SPM(R) 5 Series These values depend on PWM control algorithm FSB50825A / FSB50825AT Motion SPM(R) 5 Series VIN VIN Irr 120% of ID 100% of ID VDS ID 10% of ID ID VDS tON trr tOFF (a) Turn-on (b) Turn-off Figure 6. Switching Time Definitions C BS VCC ID VCC VB HIN HO LIN VS COM LO L VDC + V DS - VTS (R) One Leg Diagram of Motion SPM 5 Product Figure 7. Switching and RBSOA (Single-pulse) Test Circuit (Low-side) Input Signal UV Protection Status Low-side Supply, VCC RESET DETECTION RESET UVCCR UVCCD MOSFET Current Figure 8. Under-Voltage Protection (Low-Side) Input Signal UV Protection Status High-side Supply, VBS RESET DETECTION RESET UVBSR UVBSD MOSFET Current Figure 9. Under-Voltage Protection (High-Side) (c)2012 Fairchild Semiconductor Corporation FSB50825A / FSB50825AT Rev. 1.2 7 www.fairchildsemi.com (2 ) VB(U) (3 ) VCC(U) R5 (4 ) IN(UH) (5 ) IN(UL) C5 C2 (6 ) N.C (17) P VCC VB HIN HO LIN VS COM LO (18) U , VS(U) C3 (19) NU (7 ) VB(V) (8 ) VCC(V) (9 ) IN(VH) Micom (10) IN(VL) (11) VTS (12) VB(W) (13) VCC(W) (14) IN(WH) (15) IN(WL) (16) N.C VDC VCC VB HIN HO LIN VS COM LO (20) NV (21) V , VS(V) M VTS VCC VB HIN HO LIN VS COM LO (22) NW (23) W , VS(W) C4 For current-sensing and protection 15 V Supply R4 C6 R3 Figure 10. Example of Application Circuit 4th Notes: 1. About pin position, refer to Figure 1. 2. RC-coupling (R5 and C5, R4 and C6) and C4 at each input of Motion SPM(R) 5 product and MCU are useful to prevent improper input signal caused by surge-noise. 3. The voltage-drop across R3 affects the low-side switching performance and the bootstrap characteristics since it is placed between COM and the source terminal of the lowside MOSFET. For this reason, the voltage-drop across R3 should be less than 1 V in the steady-state. 4. Ground-wires and output terminals, should be thick and short in order to avoid surge-voltage and malfunction of HVIC. 5. All the filter capacitors should be connected close to Motion SPM 5 product, and they should have good characteristics for rejecting high-frequency ripple current. (c)2012 Fairchild Semiconductor Corporation FSB50825A / FSB50825AT Rev. 1.2 8 www.fairchildsemi.com FSB50825A / FSB50825AT Motion SPM(R) 5 Series C1 (1 ) COM FSB50825A / FSB50825AT Motion SPM(R) 5 Series Detailed Package Outline Drawings (FSB50825A) Max 1.00 0.50?0.10 16X (0.20) 13X (1.165) 15X1.778=26.67?0.30 (1.80) 13.34?0.30 0.60 0.45 13.34?0.3 0 (1.00) 16 17 23 14.00 12.00 ?0.20 ) 40 0. (R 1 14.55 ? 0.30 (1.165) ? 2?~6 (2.275) 12.23?0.30 3.15?0.20 (1.375) 13.13?0.3 0 (6.05) 29.00?0.20 1.95?0.30 17 2.48?0.30 19 23 (0.30) 0.60?0.10 5X Max 1.00 3.90?0.30 4X 0.50?0 .10 2X PIN19,20 2.95 ?0.50 (0.17) 3.90?0.30 2X NOTES: UNLESS OTHERWISE SPECIFIED A) THIS PACKAGE DOES NOT COMPLY TO ANY CURRENT PACKAGING STANDARD B) ALL DIMENSIONS ARE IN MILLIMETERS C) DIMENSIONS ARE EXCLUSIVE OF BURRS, MOLD FLASH, AND TIE BAR EXTRUSIONS D) ( ) IS REFERENCE E) [ ] IS ASS'Y QUALITY F) DRAWING FILENAME: MOD23DCREV4.0 G) FAIRCHILD SEMICONDUCTOR Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or data on the drawing and contact a FairchildSemiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild's worldwide therm and conditions, specifically the the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor's online packaging area for the most recent package drawings: http://www.fairchildsemi.com/dwg/MO/MOD23DC.pdf (c)2012 Fairchild Semiconductor Corporation FSB50825A / FSB50825AT Rev. 1.2 9 www.fairchildsemi.com FSB50825A / FSB50825AT Motion SPM(R) 5 Series Detailed Package Outline Drawings (FSB50825AT) Max 1.00 0.50?0.10 16X (0.20) (1.00) (2.275) 12.23?0.30 (1.375) 13.13?0.30 14.00 ?0.30 23 12.00 ?0.20 17 ) 0? (9 16 ) 40 0. (R 1 5.00 ?0.30 (1.80) 13.34?0.30 19.00 13.34?0.30 0.60 0.45 (1.165) 15X1.778=26.67?0.30 14.00 (1.165) 3.15?0.20 (6.05) 29.00?0.20 1.95?0.30 17 2.48?0.30 19 23 (0.30) 0.60?0.10 5X Max 1.00 3.90?0.30 4X 0.50?0.10 2X PIN19,20 2.95 ?0.50 (0.17) 3.90?0.30 2X NOTES: UNLESS OTHERWISE SPECIFIED A) THIS PACKAGE DOES NOT COMPLY TO ANY CURRENT PACKAGING STANDARD B) ALL DIMENSIONS ARE IN MILLIMETERS C) DIMENSIONS ARE EXCLUSIVE OF BURRS, MOLD FLASH, AND TIE BAR EXTRUSIONS D) ( ) IS REFERENCE E) DRAWING FILENAME: MOD23DFREV4.0 F) FAIRCHILD SEMICONDUCTOR Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or data on the drawing and contact a FairchildSemiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild's worldwide therm and conditions, specifically the the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor's online packaging area for the most recent package drawings: http://www.fairchildsemi.com/dwg/MO/MOD23DF.pdf (c)2012 Fairchild Semiconductor Corporation FSB50825A / FSB50825AT Rev. 1.2 10 www.fairchildsemi.com AccuPowerTM AttitudeEngineTM Awinda(R) AX-CAP(R)* BitSiCTM Build it NowTM CorePLUSTM CorePOWERTM CROSSVOLTTM CTLTM Current Transfer LogicTM DEUXPEED(R) Dual CoolTM EcoSPARK(R) EfficentMaxTM ESBCTM (R) (R) Fairchild Fairchild Semiconductor(R) FACT Quiet SeriesTM FACT(R) FastvCoreTM FETBenchTM FPSTM F-PFSTM FRFET(R) Global Power ResourceSM GreenBridgeTM Green FPSTM Green FPSTM e-SeriesTM GmaxTM GTOTM IntelliMAXTM ISOPLANARTM Marking Small Speakers Sound Louder and BetterTM MegaBuckTM MICROCOUPLERTM MicroFETTM MicroPakTM MicroPak2TM MillerDriveTM MotionMaxTM MotionGrid(R) MTi(R) MTx(R) MVN(R) mWSaver(R) OptoHiTTM OPTOLOGIC(R) OPTOPLANAR(R) (R)* (R) tm Power Supply WebDesignerTM PowerTrench(R) PowerXSTM Programmable Active DroopTM QFET(R) QSTM Quiet SeriesTM RapidConfigureTM TM Saving our world, 1mW/W/kW at a timeTM SignalWiseTM SmartMaxTM SMART STARTTM Solutions for Your SuccessTM SPM(R) STEALTHTM SuperFET(R) SuperSOTTM-3 SuperSOTTM-6 SuperSOTTM-8 SupreMOS(R) SyncFETTM Sync-LockTM TinyBoost(R) TinyBuck(R) TinyCalcTM TinyLogic(R) TINYOPTOTM TinyPowerTM TinyPWMTM TinyWireTM TranSiCTM TriFault DetectTM TRUECURRENT(R)* SerDesTM UHC(R) Ultra FRFETTM UniFETTM VCXTM VisualMaxTM VoltagePlusTM XSTM XsensTM (R) *Trademarks of System General Corporation, used under license by Fairchild Semiconductor. DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION, OR DESIGN. TO OBTAIN THE LATEST, MOST UP-TO-DATE DATASHEET AND PRODUCT INFORMATION, VISIT OUR WEBSITE AT HTTP://WWW.FAIRCHILDSEMI.COM. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. THESE SPECIFICATIONS DO NOT EXPAND THE TERMS OF FAIRCHILD'S WORLDWIDE TERMS AND CONDITIONS, SPECIFICALLY THE WARRANTY THEREIN, WHICH COVERS THESE PRODUCTS. AUTHORIZED USE Unless otherwise specified in this data sheet, this product is a standard commercial product and is not intended for use in applications that require extraordinary levels of quality and reliability. This product may not be used in the following applications, unless specifically approved in writing by a Fairchild officer: (1) automotive or other transportation, (2) military/aerospace, (3) any safety critical application - including life critical medical equipment - where the failure of the Fairchild product reasonably would be expected to result in personal injury, death or property damage. Customer's use of this product is subject to agreement of this Authorized Use policy. In the event of an unauthorized use of Fairchild's product, Fairchild accepts no liability in the event of product failure. In other respects, this product shall be subject to Fairchild's Worldwide Terms and Conditions of Sale, unless a separate agreement has been signed by both Parties. ANTI-COUNTERFEITING POLICY Fairchild Semiconductor Corporation's Anti-Counterfeiting Policy. Fairchild's Anti-Counterfeiting Policy is also stated on our external website, www.fairchildsemi.com, under Terms of Use Counterfeiting of semiconductor parts is a growing problem in the industry. All manufacturers of semiconductor products are experiencing counterfeiting of their parts. Customers who inadvertently purchase counterfeit parts experience many problems such as loss of brand reputation, substandard performance, failed applications, and increased cost of production and manufacturing delays. Fairchild is taking strong measures to protect ourselves and our customers from the proliferation of counterfeit parts. Fairchild strongly encourages customers to purchase Fairchild parts either directly from Fairchild or from Authorized Fairchild Distributors who are listed by country on our web page cited above. Products customers buy either from Fairchild directly or from Authorized Fairchild Distributors are genuine parts, have full traceability, meet Fairchild's quality standards for handling and storage and provide access to Fairchild's full range of up-to-date technical and product information. Fairchild and our Authorized Distributors will stand behind all warranties and will appropriately address and warranty issues that may arise. Fairchild will not provide any warranty coverage or other assistance for parts bought from Unauthorized Sources. Fairchild is committed to combat this global problem and encourage our customers to do their part in stopping this practice by buying direct or from authorized distributors. PRODUCT STATUS DEFINITIONS Definition of Terms Datasheet Identification Product Status Definition Advance Information Formative / In Design Datasheet contains the design specifications for product development. Specifications may change in any manner without notice. Preliminary First Production Datasheet contains preliminary data; supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice to improve design. No Identification Needed Full Production Datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice to improve the design. Obsolete Not In Production Datasheet contains specifications on a product that is discontinued by Fairchild Semiconductor. The datasheet is for reference information only. Rev. I77 (c)2012 Fairchild Semiconductor Corporation FSB50825A / FSB50825AT Rev. 1.2 11 www.fairchildsemi.com FSB50825A / FSB50825AT Motion SPM(R) 5 Series TRADEMARKS The following includes registered and unregistered trademarks and service marks, owned by Fairchild Semiconductor and/or its global subsidiaries, and is not intended to be an exhaustive list of all such trademarks. ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. "Typical" parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor 19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com (c) Semiconductor Components Industries, LLC N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5817-1050 www.onsemi.com 1 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative www.onsemi.com