MCS 0402, MCT 0603, MCU 0805, MCA 1206 - Precision Vishay Beyschlag Precision Thin Film Chip Resistors FEATURES * * * * * * Approved according to EN 140401-801 Low TCR: 10 ppm/K to 25 ppm/K Precision tolerance of value: 0.1 % and 0.25 % Superior overall stability: Class 0.1 and 0.25 Lead (Pb)-free solder contacts Compliant to RoHS directive 2002/95/EC APPLICATIONS * * * * Thin Film Flat Chip Resistors combine the proven reliability of the professional products with an advanced level of precision and stability. Therefore they are perfectly suited for applications in the fields of test and measuring equipment together with industrial and medical electronics. Automotive Test and measuring equipment Medical equipment Industrial equipment METRIC SIZE INCH: METRIC: 0402 0603 0805 1206 RR 1005M RR 1608M RR 2012M RR 3216M TECHNICAL SPECIFICATIONS DESCRIPTION MCS 0402 MCT 0603 MCU 0805 MCA 1206 Metric size RR 1005M RR 1608M RR 2012M RR 3216M 100 to 221 k 39 to 511 k 39 to 1.5 M 39 to 2 M Resistance range Resistance tolerance 0.25 %; 0.1 % Temperature coefficient 25 ppm/K; 15 ppm/K; 10 ppm/K Operation mode Precision Standard Precision Standard Precision Standard Precision Standard Climatic category (LCT/UCT/days) 10/85/56 55/125/56 10/85/56 55/125/56 10/85/56 55/125/56 10/85/56 55/125/56 Rated dissipation, P70 (1) 0.016 W 0.063 W 0.032 W 0.1 W 0.050 W 0.125 W 0.1 W 0.25 W Operating voltage, Umax. AC/DC 12.5 V 50 V 25 V 75 V 35 V 150 V 50 V 200 V Film temperature 85 C 125 C 85 C 125 C 85 C 125 C 85 C 125 C Max. resistance change at P70 for resistance range, |R/R| max., after: 100 to 221 k 39 to 511 k 39 to 1.5 M 39 to 2 M 1000 h 0.1 % 0.2 % 0.1 % 0.2 % 0.1 % 0.2 % 0.05 % 0.1 % 8000 h 0.2 % 0.4 % 0.2 % 0.4 % 0.2 % 0.4 % 0.1 % 0.25 % 225 000 h 0.5 % 1.0 % 0.5 % 1.0 % 0.5 % 1.0 % 0.25 % 0.5 % Specified lifetime 225 000 h 225 000 h 225 000 h 225 000 h 1 min; Uins 75 V 100 V 200 V 300 V Continuous 75 V 75 V 75 V 75 V 0.1 x 10-9/h 0.1 x 10-9/h 0.1 x 10-9/h 0.1 x 10-9/h Insulation voltage: Failure rate: FITobserved Note (1) The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature is not exceeded. www.vishay.com 208 For technical questions, contact: thinfilmchip@vishay.com Document Number: 28700 Revision: 18-Dec-09 MCS 0402, MCT 0603, MCU 0805, MCA 1206 - Precision Vishay Beyschlag Precision Thin Film Chip Resistors PART NUMBER AND PRODUCT DESCRIPTION (1) PART NUMBER: MCT06030D4641BPW00 M C T 0 6 0 3 0 D 4 6 4 1 B P W 0 0 MODEL/SIZE SPECIAL CHARACTER TCR VALUE TOLERANCE PACKAGING SPECIAL MCS0402 MCT0603 MCU0805 MCA1206 0 = Neutral F = 10 ppm/K E = 15 ppm/K D = 25 ppm/K 3 digit value 1 digit multiplier B = 0.1 % C = 0.25 % P1 P5 PW E1 E0 Up to 2 digits 00 = Standard MULTIPLIER 7 = *10-3 2 = *102 8 = *10-2 3 = *103 9 = *10-1 4 = *104 0 = *100 5 = *105 1 = *101 6 = *106 PRODUCT DESCRIPTION: MCT 0603 - 25 0.1 % PW 4K64 MCT 0603 - 25 0.1 % PW 4K64 MODEL SIZE TCR TOLERANCE PACKAGING RESISTANCE VALUE MCS MCT MCU MCA 0402 0603 0805 1206 10 ppm/K 15 ppm/K 25 ppm/K 0.1 % 0.25 % P1 P5 PW E1 E0 47K = 47 k 50R1 = 50.1 Note (1) Products can be ordered using either the PRODUCT DESCRIPTION or the PART NUMBER TEMPERATURE COEFFICIENT AND RESISTANCE RANGE RESISTANCE VALUE (2) DESCRIPTION TCR 25 ppm/K 15 ppm/K 10 ppm/K (3) TOLERANCE MCS 0402 MCT 0603 MCU 0805 MCA 1206 0.25 % 100 to 221 k 39 to 511 k 39 to 1.5 M 39 to 2 M 0.1 % 150 to 221 k 47 to 511 k 47 to 1.5 M 47 to 2 M 0.25 % 100 to 150 k 39 to 332 k 39 to 1 M 39 to 1.5 M 47 to 1.5 M 0.1 % 150 to 150 k 47 to 332 k 47 to 1 M 0.25 % 100 to 130 k 39 to 221 k 39 to 511 k 39 to 1 M 0.1 % 150 to 130 k 47 to 221 k 47 to 511 k 47 to 1 M Notes (2) Resistance values to be selected from E96 and E192 series, other values are available on request (3) TCR 10 is specified over the temperature range from - 10 C to 85 C Resistance ranges printed in bold are preferred TCR/tolerance combinations with optimized availability. PACKAGING REEL MODEL MCS 0402 MCT 0603 MCU 0805 MCA 1206 Document Number: 28700 Revision: 18-Dec-09 PIECES/ PAPER TAPE ON REEL 1000 10 000 1000 5000 20 000 1000 5000 20 000 1000 5000 For technical questions, contact: thinfilmchip@vishay.com CODE E1 E0 P1 P5 PW P1 P5 PW P1 P5 www.vishay.com 209 MCS 0402, MCT 0603, MCU 0805, MCA 1206 - Precision Vishay Beyschlag Precision Thin Film Chip Resistors DIMENSIONS T1 W WT H T2 L DIMENSIONS AND MASS H (mm) L (mm) W (mm) WT (mm) T1 (mm) T2 (mm) MASS (mg) MCS 0402 0.32 0.05 1.0 0.05 0.5 0.05 > 75 % of W 0.2 + 0.1/- 0.15 0.2 0.1 0.6 MCT 0603 0.45 + 0.1/- 0.05 1.55 0.05 0.85 0.1 > 75 % of W 0.3 + 0.15/- 0.2 0.3 + 0.15/- 0.2 1.9 MCU 0805 0.45 + 0.1/- 0.05 2.0 0.1 1.25 0.15 > 75 % of W 0.4 + 0.1/- 0.2 0.4 + 0.1/- 0.2 4.6 MCA 1206 0.55 0.1 3.2 + 0.1/- 0.2 1.6 0.15 > 75 % of W 0.5 0.25 0.5 0.25 9.2 TYPE SOLDER PAD DIMENSIONS X G Y Z RECOMMENDED SOLDER PAD DIMENSIONS WAVE SOLDERING TYPE REFLOW SOLDERING G (mm) Y (mm) X (mm) Z (mm) G (mm) Y (mm) X (mm) Z (mm) MCS 0402 - - - - 0.35 0.55 0.55 1.45 MCT 0603 0.55 1.10 1.10 2.75 0.65 0.70 0.95 2.05 MCU 0805 0.80 1.25 1.50 3.30 0.90 0.90 1.40 2.70 MCA 1206 1.40 1.50 1.90 4.40 1.50 1.15 1.75 3.80 Note * The given solder pad dimensions reflect the considerations for board design and assembly as outlined e.g. in standards IEC 61188-5-x, or in publication IPC-7351. They do not guarantee any supposed thermal properties, particularly as these are also strongly influenced by many other parameters. Still, the given solder pad dimensions will be found adequate for most general applications, e.g. those referring to "standard operation mode". www.vishay.com 210 For technical questions, contact: thinfilmchip@vishay.com Document Number: 28700 Revision: 18-Dec-09 MCS 0402, MCT 0603, MCU 0805, MCA 1206 - Precision Precision Thin Film Chip Resistors Vishay Beyschlag DESCRIPTION APPOVALS Production is strictly controlled and follows an extensive set of instructions established for reproducibility. A homogeneous film of metal alloy is deposited on a high grade Al203 ceramic substrate and conditioned to achieve the desired temperature coefficient. Specially designed inner contacts are deposited on both sides. A special laser is used to achieve the target value by smoothly fine trimming the resistive layer without damaging the ceramics. A further conditioning is applied in order to stabilize the trimming result. The resistor elements are covered by a blue protective coating designed for electrical, mechanical and climatic protection. The terminations receive a final pure tin on nickel plating. The resistors are approved within the IECQ-CECC Quality Assessment System for Electronic Components to the detail specification EN 140401-801 which refers to EN 60115-1, EN 140400 and the variety of environmental test procedures of the IEC 60068 (3) series. The result of the determined production is verified by an extensive testing procedure and optical inspection performed on 100 % of the individual chip resistors. Only accepted products are laid directly into the paper tape in accordance with IEC 60286-3 (3). ASSEMBLY The resistors are suitable for processing on automatic SMD assembly systems and for automatic soldering using wave, reflow or vapour phase. The encapsulation is resistant to all cleaning solvents commonly used in the electronics industry, including alcohols, esters and aqueous solutions. The suitability of conformal coatings, if applied, shall be qualified by appropriate means to ensure the long-term stability of the whole system. The resistors are RoHS compliant, the pure tin plating provides compatibility with lead (Pb)-free and lead-containing soldering processes. Solderability is specified for 2 years after production or requalification. The permitted storage time is 20 years. The immunity of the plating against tin whisker growth has been proven under extensive testing. Conformity is attested by the use of the CECC Logo ( the Mark of Conformity on the package label. ) as Vishay BEYSCHLAG has achieved "Approval of Manufacturer" in accordance with IEC QC 001002-3, clause 2. The release certificate for "Technology Approval Schedule" in accordance with CECC 240001 based on IEC QC 001002-3, clause 6 is granted for the Vishay BEYSCHLAG manufacturing process. RELATED PRODUCTS On request, resistors are available with established reliability in accordance with EN 140401-801 version E. Please refer to the special datasheet document no. 28744 for information on failure rate level, available resistance ranges and order codes. For more information about products with higher rated power and higher operation temperature please refer to the Professional Thin Film Chip Resistor datasheet document no. 28705. Precision chip resistor arrays may be used in voltage divider applications or precision amplifiers where close matching between multiple resistors is necessary. Please refer to the ACAS 0612 - Precision datasheet document no. 28751. All products comply with the GADSL (1) and the CEFIC-EECA-EICTA (2) list of legal restrictions on hazardous substances. This includes full compliance with the following directives: * 2000/53/EC End of Vehicle life Directive (ELV) an Annex II (ELV II) * 2002/95/EC Restriction of the Substances Directive (RoHS) use of Hazardous * 2002/96/EC Waste Electrical and Electronic Equipment Directive (WEEE) Notes (1) (2) (3) Global Automotive Declarable Substance List, see www.gadsl.org CEFIC (European Chemical Industry Council), EECA (European Electronic Component Manufacturers Association), EICTA (European trade organisation representing the information and communications technology and consumer electronics), see www.eicta.org/index.php?id=995 issues environment policy chemicals chemicals for electronics The quoted IEC standards are also released as EN standards with the same number and identical contents Document Number: 28700 Revision: 18-Dec-09 For technical questions, contact: thinfilmchip@vishay.com www.vishay.com 211 MCS 0402, MCT 0603, MCU 0805, MCA 1206 - Precision Vishay Beyschlag Precision Thin Film Chip Resistors Power Dissipation P FUNCTIONAL PERFORMANCE MCS 0402 MCT 0603 MCU 0805 MCA 1206 0.2 W 0.1 0 0 - 50 50 70 100 C 150 Ambient Temperature amb Power Dissipation P Derating - Standard Operation MCS 0402 MCT 0603 MCU 0805 MCA 1206 0.2 W 0.1 0 0 - 50 50 70 100 C 150 Ambient Temperature amb Current Noise A 1 Derating - Precision Operation 1 V/V 0.1 MCT 0603 MCU 0805 MCA 1206 0.01 1 k 10 k 100 k 1 M 10 M Resistance Value R Current Noise A1 www.vishay.com 212 In accordance with IEC 60195 For technical questions, contact: thinfilmchip@vishay.com Document Number: 28700 Revision: 18-Dec-09 MCS 0402, MCT 0603, MCU 0805, MCA 1206 - Precision Vishay Beyschlag Precision Thin Film Chip Resistors TEST AND REQUIREMENTS All tests are carried out in accordance with the following specifications: EN 60115-1, generic specification (includes tests) EN 140400, sectional specification (includes schedule for qualification approval) EN 140401-801, detail specification (includes schedule for conformance inspection) The components are approved in accordance with the European CECC-system, where applicable. The following table contains only the most important tests. For the full test schedule refer to the documents listed above. The testing also covers most of the requirements specified by EIA/IS-703 and JIS-C-5202. The tests are carried out in accordance with IEC 60068 and under standard atmospheric conditions in accordance with IEC 60068-1, 5.3. Climatic category LCT/UCT/56 (rated temperature range: Lower Category Temperature, Upper Category Temperature; damp heat, long term, 56 days) is valid. Unless otherwise specified the following values apply: Temperature: 15 C to 35 C Relative humidity: 45 % to 75 % Air pressure: 86 kPa to 106 kPa (860 mbar to 1060 mbar). The components are mounted for testing on boards in accordance with EN 60115-1, 4.31 unless otherwise specified. The parameters stated in the Test Procedures and Requirements table are based on the required tests and permitted limits of EN 140401-801. However, some additional tests and a number of improvements against those minimum requirements have been included. TEST PROCEDURES AND REQUIREMENTS EN 60115-1 CLAUSE IEC 60068-2 TEST METHOD TEST PROCEDURE REQUIREMENTS PERMISSIBLE CHANGE (R) STABILITY CLASS 0.1 STABILITY CLASS 0.25 MCS 0402 470 to 10 k > 10 k to 52.3 k MCT 0603 100 to 10 k 39 to < 100 ; > 10 k to 511 k MCU 0805 100 to 47.5 k 39 to < 100 ; > 47.5 k to 1.5 M MCA 1206 47 to 332 k 39 to < 47 ; > 332 k to 2 M Stability for product types: 0.1 % R; 0.25 % R 4.5 - Resistance 4.8.4.2 - Temperature coefficient - Endurance at 70 C: Precision operation mode 4.25.1 - 4.25.3 4.24 Endurance at 70 C: Standard operation mode At (20/- 10/20) C and (20/85/20) C 25 ppm/K; 15 ppm/K; 10 ppm/K U = P 70 x R or U = Umax.; whichever is the less severe; 1.5 h on; 0.5 h off; 70 C; 1000 h (0.1 % R + 0.02 ) (1) 70 C; 8000 h (0.2 % R + 0.02 ) (1) U = P 70 x R or U = Umax.; whichever is the less severe; 1.5 h on; 0.5 h off; 70 C; 1000 h (0.2 % R + 0.02 ) (1) 70 C; 8000 h (0.4 % R + 0.05 ) (1) - Endurance at upper category temperature 85 C; 1000 h 125 C; 1000 h (0.1 % R + 0.02 ) (0.2 % R + 0.02 ) (0.2 % R + 0.02 ) (0.25 % R + 0.05 ) 78 (Cab) Damp heat, steady state (40 2) C; 56 days; (93 3) % RH (0.1 % R + 0.02 ) (0.25 % R + 0.05 ) Document Number: 28700 Revision: 18-Dec-09 For technical questions, contact: thinfilmchip@vishay.com www.vishay.com 213 MCS 0402, MCT 0603, MCU 0805, MCA 1206 - Precision Vishay Beyschlag Precision Thin Film Chip Resistors TEST PROCEDURES AND REQUIREMENTS EN 60115-1 CLAUSE IEC 60068-2 TEST METHOD TEST PROCEDURE REQUIREMENTS PERMISSIBLE CHANGE (R) STABILITY CLASS 0.1 STABILITY CLASS 0.25 MCS 0402 470 to 10 k > 10 k to 52.3 k MCT 0603 100 to 10 k 39 to < 100 ; > 10 k to 511 k MCU 0805 100 to 47.5 k 39 to < 100 ; > 47.5 k to 1.5 M MCA 1206 47 to 332 k 39 to < 47 ; > 332 k to 2 M (0.1 % R + 0.02 ) (0.25 % R + 0.05 ) Stability for product types: Climatic sequence: 4.23 4.23.2 2 (Ba) dry heat UCT; 16 h 4.23.3 30 (Db) damp heat, cyclic 55 C; 24 h; > 90 % RH; 1 cycle 4.23.4 1 (Aa) cold LCT; 2 h 4.23.5 13 (M) low air pressure 8.5 kPa; 2 h; (25 10) C 4.23.6 30 (Db) damp heat, cyclic 55 C; 5 days; > 95 % to 100 % RH; 5 cycles LCT = - 55 C; UCT = 125 C 1 (Aa) Cold - 55 C; 2 h (0.05 % R + 0.01 ) Rapid change of temperature 30 min at LCT and 30 min at UCT; LCT = - 10 C UCT = 85 C; 5 cycles (0.05 % R + 0.01 ) no visible damage LCT = - 55 C; UCT = 125 C; 1000 cycles (0.25 % R + 0.05 ) no visible damage - 4.19 4.13 14 (Na) - Short time overload; precision operation mode Short time overload; standard operation mode 4.27 4.37 4.22 www.vishay.com 214 U = 2.5 x P 70 x R or U = 2 x Umax.; whichever is the less severe; 5s Severity no. 4: U = 10 x P 70 x R or U = 2 x Umax.; whichever is the less severe; 10 pulses 10 s/700 s (0.05 % R + 0.01 ) (0.05 % R + 0.01 ) - Single pulse high voltage overload; standard operation mode - Periodic electric overload; standard operation mode 15 x P 70 x R or U = 2 x Umax.; whichever is the less severe; 0.1 s on; 2.5 s off; 1000 cycles (0.5 % R + 0.05 ) (2) no visible damage Vibration Endurance by sweeping; 10 Hz to 2000 Hz; no resonance; amplitude 1.5 mm or 200 m/s2; 6 h (0.05 % R + 0.01 ) no visible damage 6 (Fc) (0.5 % R + 0.05 ) (2) no visible damage U= For technical questions, contact: thinfilmchip@vishay.com Document Number: 28700 Revision: 18-Dec-09 MCS 0402, MCT 0603, MCU 0805, MCA 1206 - Precision Vishay Beyschlag Precision Thin Film Chip Resistors TEST PROCEDURES AND REQUIREMENTS EN 60115-1 CLAUSE IEC 60068-2 TEST METHOD TEST PROCEDURE REQUIREMENTS PERMISSIBLE CHANGE (R) STABILITY CLASS 0.1 STABILITY CLASS 0.25 MCS 0402 470 to 10 k > 10 k to 52.3 k MCT 0603 100 to 10 k 39 to < 100 ; > 10 k to 511 k MCU 0805 100 to 47.5 k 39 to < 100 ; > 47.5 k to 1.5 M MCA 1206 47 to 332 k 39 to < 47 ; > 332 k to 2 M Stability for product types: Solder bath method; SnPb40; non-activated flux (215 3) C; (3 0.3) s Good tinning ( 95 % covered); no visible damage 4.17.2 58 (Td) Solderability Solder bath method; SnAg3Cu0.5 or SnAg3.5; non-activated flux (235 3) C; (2 0.2) s 4.18.2 58 (Td) Resistance to soldering heat Solder bath method; (260 5) C; (10 1) s (0.05 % R + 0.01 ) 4.29 45 (XA) Component solvent resistance Isopropyl alcohol + 50 C; method 2 No visible damage 4.32 21 (Ue3) Shear (adhesion) 4.33 21 (Ue1) Substrate bending Depth 2 mm, 3 times (0.05 % R + 0.01 ) no visible damage, no open circuit in bent position 4.7 - Voltage proof URMS = Uins; (60 5) s No flashover or breakdown Flammability IEC 60695-2-2, needle flame test; 10 s No burning after 30 s 4.35 - RR 1005M and RR 1608M; 9N No visible damage RR 2012M and RR 3216M; 45 N Special requirements for type MCA 1206 - Endurance at 70 C: Precision operation mode 4.25.1 - Endurance at 70 C: Standard operation mode U = P 70 x R or U = Umax.; whichever is the less severe; 70 C; 1000 h (0.05 % R + 0.02 ) 70 C; 8000 h (0.1 % R + 0.02 ) U = P 70 x R or U = Umax.; whichever is the less severe; 70 C; 1000 h (0.1 % R + 0.02 ) 70 C; 8000 h (0.25 % R + 0.05 ) Notes (1) See 4.25.1 (above): special requirements for type MCA 1206 (2) The pulse load stability of professional MFC resistors applies for precision resistors also. However, severe pulse loads are likely to jeopardise precision stability requirements. Document Number: 28700 Revision: 18-Dec-09 For technical questions, contact: thinfilmchip@vishay.com www.vishay.com 215 MCS 0402, MCT 0603, MCU 0805, MCA 1206 - Precision Vishay Beyschlag Precision Thin Film Chip Resistors 12NC INFORMATION FOR HISTORICAL CODING REFERENCE ONLY * The resistors have a 12-digit numeric code starting with 2312. * The subsequent 4 digits indicate the resistor type, specification and packaging; see the 12NC table. * The remaining 4 digits indicate the resistance value: - The first 3 digits indicate the resistance value. - The last digit indicates the resistance decade in accordance with the 12NC Indicating Resistance Decade table. Last Digit of 12NC Indicating Resistance Decade RESISTANCE DECADE LAST DIGIT 10 to 99.9 9 100 to 999 1 1 k to 9.99 k 2 10 k to 99.9 k 3 100 k to 999 k 4 1 M to 9.99 M 5 12NC Example The 12NC of a MCT 0603 resistor, value 47 k and TCR 25 with 0.1 % tolerance, supplied in cardboard tape of 5000 units per reel is: 2312 216 74703. 12NC - Resistors type and packaging CODE 2312... ..... DESCRIPTION TYPE TCR 25 ppm/K MCS 0402 15 ppm/K 10 ppm/K 25 ppm/K MCT 0603 15 ppm/K 10 ppm/K 25 ppm/K MCU 0805 15 ppm/K 10 ppm/K 25 ppm/K MCA 1206 15 ppm/K 10 ppm/K www.vishay.com 216 CARDBOARD TAPE ON REEL TOL. P1 1000 UNITS P5 5000 UNITS PW 20 000 UNITS E1 1000 UNITS E0 10 000 UNITS 0.25 % - - - 261 6.... 276 6.... 0.1 % - - - 261 7.... 276 7.... 0.25 % - - - 262 6.... 277 6.... 0.1 % - - - 262 7.... 277 7.... 0.25 % - - - 263 6.... 278 6.... 0.1 % - - - 263 7.... 278 7.... 0.25 % 201 6.... 216 6.... 206 6.... - - 0.1 % 201 7.... 216 7.... 206 7.... - - 0.25 % 202 6.... 217 6.... 207 6.... - - 0.1 % 202 7.... 217 7.... 207 7.... - - 0.25 % 203 6.... 218 6.... 208 6.... - - 0.1 % 203 7.... 218 7.... 208 7.... - - 0.25 % 241 6.... 256 6.... 246 6.... - - 0.1 % 241 7.... 256 7.... 246 7.... - - 0.25 % 242 6.... 257 6.... 247 6.... - - 0.1 % 242 7.... 257 7.... 247 7.... - - 0.25 % 243 6.... 258 6.... 248 6.... - - 0.1 % 243 7.... 258 7.... 248 7.... - - 0.25 % 381 6.... 396 6.... 386 6.... - - 0.1 % 381 7.... 396 7.... 386 7.... - - 0.25 % 382 6.... 397 6.... 387 6.... - - 0.1 % 382 7.... 397 7.... 387 7.... - - 0.25 % 383 6.... 398 6.... 388 6.... - - 0.1 % 383 7.... 398 7.... 388 7.... - - For technical questions, contact: thinfilmchip@vishay.com Document Number: 28700 Revision: 18-Dec-09 Legal Disclaimer Notice Vishay Disclaimer All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 18-Jul-08 www.vishay.com 1