2 Mbit / 4 Mbit / 8 Mbit (x16) Multi-Purpose Flash SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A SST39LF/VF200A / 400A / 800A3.0 & 2.7V 2Mb / 4Mb / 8Mb (x16) MPF memories Data Sheet FEATURES: * Organized as 128K x16 / 256K x16 / 512K x16 * Single Voltage Read and Write Operations - 3.0-3.6V for SST39LF200A/400A/800A - 2.7-3.6V for SST39VF200A/400A/800A * Superior Reliability - Endurance: 100,000 Cycles (typical) - Greater than 100 years Data Retention * Low Power Consumption (typical values at 14 MHz) - Active Current: 9 mA (typical) - Standby Current: 3 A (typical) * Sector-Erase Capability - Uniform 2 KWord sectors * Block-Erase Capability - Uniform 32 KWord blocks * Fast Read Access Time - 45 and 55 ns for SST39LF200A - 55 ns for SST39LF400A/800A - 70 ns for SST39VF200A/400A/800A * Latched Address and Data * Fast Erase and Word-Program - Sector-Erase Time: 18 ms (typical) - Block-Erase Time: 18 ms (typical) - Chip-Erase Time: 70 ms (typical) - Word-Program Time: 14 s (typical) - Chip Rewrite Time: 2 seconds (typical) for SST39LF/VF200A 4 seconds (typical) for SST39LF/VF400A 8 seconds (typical) for SST39LF/VF800A * Automatic Write Timing - Internal VPP Generation * End-of-Write Detection - Toggle Bit - Data# Polling * CMOS I/O Compatibility * JEDEC Standard - Flash EEPROM Pinouts and command sets * Packages Available - 48-lead TSOP (12mm x 20mm) - 48-ball TFBGA (6mm x 8mm) - 48-ball WFBGA (4mm x 6mm) - 48-bump XFLGA (4mm x 6mm) - 4 and 8Mbit * All non-Pb (lead-free) devices are RoHS compliant PRODUCT DESCRIPTION The SST39LF200A/400A/800A and SST39VF200A/400A/ 800A devices are 128K x16 / 256K x16 / 512K x16 CMOS Multi-Purpose Flash (MPF) manufactured with SST proprietary, high-performance CMOS SuperFlash technology. The split-gate cell design and thick oxide tunneling injector attain better reliability and manufacturability compared with alternate approaches. The SST39LF200A/400A/800A write (Program or Erase) with a 3.0-3.6V power supply. The SST39VF200A/400A/800A write (Program or Erase) with a 2.7-3.6V power supply. These devices conform to JEDEC standard pinouts for x16 memories. Featuring high-performance Word-Program, the SST39LF200A/400A/800A and SST39VF200A/400A/ 800A devices provide a typical Word-Program time of 14 sec. The devices use Toggle Bit or Data# Polling to detect the completion of the Program or Erase operation. To protect against inadvertent write, they have on-chip hardware and software data protection schemes. Designed, manufactured, and tested for a wide spectrum of applications, these devices are offered with a guaranteed typical endurance of 100,000 cycles. Data retention is rated at greater than 100 years. (c)2007 Silicon Storage Technology, Inc. S71117-10-000 08/07 1 The SST39LF200A/400A/800A and SST39VF200A/400A/ 800A devices are suited for applications that require convenient and economical updating of program, configuration, or data memory. For all system applications, they significantly improve performance and reliability, while lowering power consumption. They inherently use less energy during Erase and Program than alternative flash technologies. When programming a flash device, the total energy consumed is a function of the applied voltage, current, and time of application. Since for any given voltage range, the SuperFlash technology uses less current to program and has a shorter erase time, the total energy consumed during any Erase or Program operation is less than alternative flash technologies. These devices also improve flexibility while lowering the cost for program, data, and configuration storage applications. The SuperFlash technology provides fixed Erase and Program times, independent of the number of Erase/Program cycles that have occurred. Therefore the system software or hardware does not have to be modified or de-rated as is necessary with alternative flash technologies, whose Erase and Program times increase with accumulated Erase/Program cycles. The SST logo and SuperFlash are registered trademarks of Silicon Storage Technology, Inc. MPF is a trademark of Silicon Storage Technology, Inc. These specifications are subject to change without notice. http://store.iiic.cc/ 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet Sector/Block-Erase Operation To meet surface mount requirements, the SST39LF200A/ 400A/800A and SST39VF200A/400A/800A are offered in 48-lead TSOP packages and 48-ball TFBGA packages as well as Micro-Packages. See Figures 2, 3, and 4 for pin assignments. The Sector- (or Block-) Erase operation allows the system to erase the device on a sector-by-sector (or block-byblock) basis. The SST39LF200A/400A/800A and SST39VF200A/400A/800A offers both Sector-Erase and Block-Erase mode. The sector architecture is based on uniform sector size of 2 KWord. The Block-Erase mode is based on uniform block size of 32 KWord. The SectorErase operation is initiated by executing a six-byte command sequence with Sector-Erase command (30H) and sector address (SA) in the last bus cycle. The Block-Erase operation is initiated by executing a six-byte command sequence with Block-Erase command (50H) and block address (BA) in the last bus cycle. The sector or block address is latched on the falling edge of the sixth WE# pulse, while the command (30H or 50H) is latched on the rising edge of the sixth WE# pulse. The internal Erase operation begins after the sixth WE# pulse. The End-ofErase operation can be determined using either Data# Polling or Toggle Bit methods. See Figures 11 and 12 for timing waveforms. Any commands issued during the Sector- or Block-Erase operation are ignored. Device Operation Commands are used to initiate the memory operation functions of the device. Commands are written to the device using standard microprocessor write sequences. A command is written by asserting WE# low while keeping CE# low. The address bus is latched on the falling edge of WE# or CE#, whichever occurs last. The data bus is latched on the rising edge of WE# or CE#, whichever occurs first. Read The Read operation of the SST39LF200A/400A/800A and SST39VF200A/400A/800A is controlled by CE# and OE#, both have to be low for the system to obtain data from the outputs. CE# is used for device selection. When CE# is high, the chip is deselected and only standby power is consumed. OE# is the output control and is used to gate data from the output pins. The data bus is in high impedance state when either CE# or OE# is high. Refer to the Read cycle timing diagram for further details (Figure 5). Chip-Erase Operation The SST39LF200A/400A/800A and SST39VF200A/400A/ 800A provide a Chip-Erase operation, which allows the user to erase the entire memory array to the "1" state. This is useful when the entire device must be quickly erased. Word-Program Operation The SST39LF200A/400A/800A and SST39VF200A/400A/ 800A are programmed on a word-by-word basis. Before programming, the sector where the word exists must be fully erased. The Program operation is accomplished in three steps. The first step is the three-byte load sequence for Software Data Protection. The second step is to load word address and word data. During the Word-Program operation, the addresses are latched on the falling edge of either CE# or WE#, whichever occurs last. The data is latched on the rising edge of either CE# or WE#, whichever occurs first. The third step is the internal Program operation which is initiated after the rising edge of the fourth WE# or CE#, whichever occurs first. The Program operation, once initiated, will be completed within 20 s. See Figures 6 and 7 for WE# and CE# controlled Program operation timing diagrams and Figure 18 for flowcharts. During the Program operation, the only valid reads are Data# Polling and Toggle Bit. During the internal Program operation, the host is free to perform additional tasks. Any commands issued during the internal Program operation are ignored. The Chip-Erase operation is initiated by executing a sixbyte command sequence with Chip-Erase command (10H) at address 5555H in the last byte sequence. The Erase operation begins with the rising edge of the sixth WE# or CE#, whichever occurs first. During the Erase operation, the only valid read is Toggle Bit or Data# Polling. See Table 4 for the command sequence, Figure 10 for timing diagram, and Figure 21 for the flowchart. Any commands issued during the Chip-Erase operation are ignored. Write Operation Status Detection The SST39LF200A/400A/800A and SST39VF200A/400A/ 800A provide two software means to detect the completion of a write (Program or Erase) cycle, in order to optimize the system write cycle time. The software detection includes two status bits: Data# Polling (DQ7) and Toggle Bit (DQ6). The End-of-Write detection mode is enabled after the rising edge of WE#, which initiates the internal Program or Erase operation. (c)2007 Silicon Storage Technology, Inc. S71117-10-000 2 http://store.iiic.cc/ 08/07 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet Data Protection The actual completion of the nonvolatile write is asynchronous with the system; therefore, either a Data# Polling or Toggle Bit read may be simultaneous with the completion of the write cycle. If this occurs, the system may possibly get an erroneous result, i.e., valid data may appear to conflict with either DQ7 or DQ6. In order to prevent spurious rejection, if an erroneous result occurs, the software routine should include a loop to read the accessed location an additional two (2) times. If both reads are valid, then the device has completed the write cycle, otherwise the rejection is valid. The SST39LF200A/400A/800A and SST39VF200A/400A/ 800A provide both hardware and software features to protect nonvolatile data from inadvertent writes. Hardware Data Protection Noise/Glitch Protection: A WE# or CE# pulse of less than 5 ns will not initiate a write cycle. VDD Power Up/Down Detection: The Write operation is inhibited when VDD is less than 1.5V. Data# Polling (DQ7) Write Inhibit Mode: Forcing OE# low, CE# high, or WE# high will inhibit the Write operation. This prevents inadvertent writes during power-up or power-down. When the SST39LF200A/400A/800A and SST39VF200A/ 400A/800A are in the internal Program operation, any attempt to read DQ7 will produce the complement of the true data. Once the Program operation is completed, DQ7 will produce true data. Note that even though DQ7 may have valid data immediately following the completion of an internal Write operation, the remaining data outputs may still be invalid: valid data on the entire data bus will appear in subsequent successive Read cycles after an interval of 1 s. During internal Erase operation, any attempt to read DQ7 will produce a `0'. Once the internal Erase operation is completed, DQ7 will produce a `1'. The Data# Polling is valid after the rising edge of fourth WE# (or CE#) pulse for Program operation. For Sector-, Block- or Chip-Erase, the Data# Polling is valid after the rising edge of sixth WE# (or CE#) pulse. See Figure 8 for Data# Polling timing diagram and Figure 19 for a flowchart. Software Data Protection (SDP) The SST39LF200A/400A/800A and SST39VF200A/400A/ 800A provide the JEDEC approved Software Data Protection scheme for all data alteration operations, i.e., Program and Erase. Any Program operation requires the inclusion of the three-byte sequence. The three-byte load sequence is used to initiate the Program operation, providing optimal protection from inadvertent Write operations, e.g., during the system power-up or power-down. Any Erase operation requires the inclusion of six-byte sequence. This group of devices are shipped with the Software Data Protection permanently enabled. See Table 4 for the specific software command codes. During SDP command sequence, invalid commands will abort the device to Read mode within TRC. The contents of DQ15-DQ8 can be VIL or VIH, but no other value, during any SDP command sequence. Toggle Bit (DQ6) During the internal Program or Erase operation, any consecutive attempts to read DQ6 will produce alternating 1s and 0s, i.e., toggling between 1 and 0. When the internal Program or Erase operation is completed, the DQ6 bit will stop toggling. The device is then ready for the next operation. The Toggle Bit is valid after the rising edge of fourth WE# (or CE#) pulse for Program operation. For Sector-, Block- or Chip-Erase, the Toggle Bit is valid after the rising edge of sixth WE# (or CE#) pulse. See Figure 9 for Toggle Bit timing diagram and Figure 19 for a flowchart. Common Flash Memory Interface (CFI) The SST39LF200A/400A/800A and SST39VF200A/400A/ 800A also contain the CFI information to describe the characteristics of the device. In order to enter the CFI Query mode, the system must write three-byte sequence, same as Software ID Entry command with 98H (CFI Query command) to address 5555H in the last byte sequence. Once the device enters the CFI Query mode, the system can read CFI data at the addresses given in Tables 5 through 9. The system must write the CFI Exit command to return to Read mode from the CFI Query mode. (c)2007 Silicon Storage Technology, Inc. S71117-10-000 3 http://store.iiic.cc/ 08/07 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet Product Identification Product Identification Mode Exit/ CFI Mode Exit The Product Identification mode identifies the devices as the SST39LF/VF200A, SST39LF/VF400A and SST39LF/ VF800A and manufacturer as SST. This mode may be accessed by software operations. Users may use the Software Product Identification operation to identify the part (i.e., using the device ID) when using multiple manufacturers in the same socket. For details, see Table 4 for software operation, Figure 13 for the Software ID Entry and Read timing diagram, and Figure 20 for the Software ID Entry command sequence flowchart. In order to return to the standard Read mode, the Software Product Identification mode must be exited. Exit is accomplished by issuing the Software ID Exit command sequence, which returns the device to the Read mode. This command may also be used to reset the device to the Read mode after any inadvertent transient condition that apparently causes the device to behave abnormally, e.g., not read correctly. Please note that the Software ID Exit/ CFI Exit command is ignored during an internal Program or Erase operation. See Table 4 for software command codes, Figure 15 for timing waveform, and Figure 20 for a flowchart. TABLE 1: Product Identification Address Data 0000H 00BFH SST39LF/VF200A 0001H 2789H SST39LF/VF400A 0001H 2780H SST39LF/VF800A 0001H 2781H Manufacturer's ID Device ID T1.3 1117 X-Decoder Memory Address SuperFlash Memory Address Buffer & Latches Y-Decoder CE# OE# I/O Buffers and Data Latches Control Logic WE# DQ15 - DQ0 1117 B1.2 FIGURE 1: Functional Block Diagram (c)2007 Silicon Storage Technology, Inc. S71117-10-000 4 http://store.iiic.cc/ 08/07 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet SST39LF/VF200A SST39LF/VF400A SST39LF/VF800A SST39LF/VF800A SST39LF/VF400A SST39LF/VF200A A15 A14 A13 A12 A11 A10 A9 A8 NC NC WE# NC NC NC NC A18 A17 A7 A6 A5 A4 A3 A2 A1 A15 A14 A13 A12 A11 A10 A9 A8 NC NC WE# NC NC NC NC NC NC A7 A6 A5 A4 A3 A2 A1 A15 A14 A13 A12 A11 A10 A9 A8 NC NC WE# NC NC NC NC NC A17 A7 A6 A5 A4 A3 A2 A1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Standard Pinout Top View Die Up A16 NC VSS DQ15 DQ7 DQ14 DQ6 DQ13 DQ5 DQ12 DQ4 VDD DQ11 DQ3 DQ10 DQ2 DQ9 DQ1 DQ8 DQ0 OE# VSS CE# A0 A16 NC VSS DQ15 DQ7 DQ14 DQ6 DQ13 DQ5 DQ12 DQ4 VDD DQ11 DQ3 DQ10 DQ2 DQ9 DQ1 DQ8 DQ0 OE# VSS CE# A0 A16 NC VSS DQ15 DQ7 DQ14 DQ6 DQ13 DQ5 DQ12 DQ4 VDD DQ11 DQ3 DQ10 DQ2 DQ9 DQ1 DQ8 DQ0 OE# VSS CE# A0 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 1117 48-tsop P01.2 FIGURE 2: Pin Assignments for 48-Lead TSOP TOP VIEW (balls facing down) 6 5 4 3 2 1 A13 A12 A14 A15 A16 NC DQ15 VSS A9 A8 A10 A11 DQ7 DQ14 DQ13 DQ6 WE# NC NC NC DQ5 DQ12 VDD DQ4 NC NC NC NC DQ2 DQ10 DQ11 DQ3 A7 NC A6 A5 DQ0 DQ8 DQ9 DQ1 A3 A4 A2 A1 A0 CE# OE# VSS A B C D E F G H TOP VIEW (balls facing down) TOP VIEW (balls facing down) 4 3 2 1 A9 A8 WE# NC NC A7 NC A17 A10 NC NC A6 6 A15 A16 NC DQ15 VSS 5 A11 DQ7 DQ14 DQ13 DQ6 4 NC DQ5 DQ12 VDD DQ4 NC DQ2 DQ10 DQ11 DQ3 A5 DQ0 DQ8 DQ9 DQ1 A3 A4 A2 A1 A0 CE# OE# VSS A B C D E F G 3 1117 48-tfbga P02_4.0 5 A13 A12 A14 SST39LF/VF800A 2 1 H A13 A12 A14 A15 A16 NC DQ15 VSS A9 A8 A10 A11 DQ7 DQ14 DQ13 DQ6 WE# NC NC NC DQ5 DQ12 VDD DQ4 NC NC A18 NC DQ2 DQ10 DQ11 DQ3 A7 A17 A6 A5 DQ0 DQ8 DQ9 DQ1 A3 A4 A2 A1 A0 CE# OE# VSS A B C D E F G 1117 48-tfbga P02_8.0 SST39LF/VF400A 6 1117 48-tfbga P02_2.0 SST39LF/VF200A H FIGURE 3: Pin Assignments for 48-Ball TFBGA (c)2007 Silicon Storage Technology, Inc. S71117-10-000 5 http://store.iiic.cc/ 08/07 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet TOP VIEW (balls facing down) SST39VF200A 6 A2 A4 A6 NC A1 A3 A7 NC A0 A5 NC NC NC WE# NC A9 A11 NC A10 A13 A14 A8 A12 A15 5 4 CE# DQ8 DQ10 VSS OE# DQ9 DQ4 DQ11 A16 2 NC NC DQ5 DQ6 DQ7 1 DQ0 DQ1 DQ2 DQ3 A B C D E VDD DQ12 DQ13 DQ14 DQ15 VSS F G H J K NC A9 A11 NC A10 A13 A14 A8 A12 A15 1117 48-xflga P03_2.0 3 L TOP VIEW (balls facing down) SST39LF/VF400A 6 A2 A4 A6 A17 A1 A3 A7 NC A0 A5 NC NC NC WE# 5 4 3 DQ8 DQ10 VSS OE# DQ9 DQ4 DQ11 A16 NC NC DQ5 DQ6 DQ7 1 DQ0 DQ1 DQ2 DQ3 A B C D E VDD DQ12 DQ13 DQ14 DQ15 VSS F G H J K 1117 48-xflga P03_4.0 CE# 2 L TOP VIEW (balls facing down) SST39LF/VF800A 6 A2 A4 A6 A17 A1 A3 A7 NC A0 A5 A18 NC NC WE# NC A9 A11 NC A10 A13 A14 A8 A12 A15 5 4 3 DQ8 DQ10 VSS OE# DQ9 DQ4 DQ11 A16 NC NC DQ5 DQ6 DQ7 1 DQ0 DQ1 DQ2 DQ3 A B C D E VDD DQ12 DQ13 DQ14 DQ15 VSS F G H J K 1117 48-xflga P03_8.0 CE# 2 L FIGURE 4: Pin Assignments for 48-Ball WFBGA and 48-Bump XFLGA (c)2007 Silicon Storage Technology, Inc. S71117-10-000 6 http://store.iiic.cc/ 08/07 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet TABLE 2: Pin Description Symbol Pin Name Functions AMS1-A0 Address Inputs To provide memory addresses. During Sector-Erase AMS-A11 address lines will select the sector. During Block-Erase AMS-A15 address lines will select the block. DQ15-DQ0 Data Input/output To output data during Read cycles and receive input data during Write cycles. Data is internally latched during a Write cycle. The outputs are in tri-state when OE# or CE# is high. CE# Chip Enable To activate the device when CE# is low. OE# Output Enable To gate the data output buffers. WE# Write Enable To control the Write operations. VDD Power Supply To provide power supply voltage: VSS Ground NC No Connection 3.0-3.6V for SST39LF200A/400A/800A 2.7-3.6V for SST39VF200A/400A/800A Unconnected pins. T2.2 1117 1. AMS = Most significant address AMS = A16 for SST39LF/VF200A, A17 for SST39LF/VF400A, and A18 for SST39LF/VF800A TABLE 3: Operation Modes Selection Mode CE# OE# WE# Read Program DQ Address VIL VIL VIL VIH VIH DOUT AIN VIL DIN AIN VIH VIL X1 Sector or Block address, XXH for Chip-Erase Erase VIL Standby VIH X X High Z X X VIL X High Z/ DOUT X X X VIH High Z/ DOUT X VIL VIL VIH Write Inhibit Product Identification Software Mode See Table 4 T3.4 1117 1. X can be VIL or VIH, but no other value. (c)2007 Silicon Storage Technology, Inc. S71117-10-000 7 http://store.iiic.cc/ 08/07 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet TABLE 4: Software Command Sequence Command Sequence 1st Bus Write Cycle Addr1 Data2 2nd Bus Write Cycle Addr1 Data2 3rd Bus Write Cycle Addr1 4th Bus Write Cycle Data2 Addr1 Data2 Data AAH Word-Program 5555H AAH 2AAAH 55H 5555H A0H WA3 Sector-Erase 5555H AAH 2AAAH 55H 5555H 80H 5555H 5th Bus Write Cycle 6th Bus Write Cycle Addr1 Data2 Addr1 Data2 2AAAH 55H SAX4 30H 4 Block-Erase 5555H AAH 2AAAH 55H 5555H 80H 5555H AAH 2AAAH 55H BAX Chip-Erase 5555H AAH 2AAAH 55H 5555H 80H 5555H AAH 2AAAH 55H 5555H Software ID Entry5,6 5555H AAH 2AAAH 55H 5555H 90H CFI Query Entry5 5555H AAH 2AAAH 55H 5555H 98H XXH F0H 5555H AAH 2AAAH 55H 5555H F0H Software ID CFI Exit Exit7/ Software ID Exit7/ CFI Exit 50H 10H T4.3 1117 1. Address format A14-A0 (Hex), Addresses AMS-A15 can be VIL or VIH, but no other value, for the Command sequence. AMS = Most significant address AMS = A16 for SST39LF/VF200A, A17 for SST39LF/VF400A, and A18 for SST39LF/VF800A 2. DQ15-DQ8 can be VIL or VIH, but no other value, for the Command sequence 3. WA = Program word address 4. SAX for Sector-Erase; uses AMS-A11 address lines BAX for Block-Erase; uses AMS-A15 address lines 5. The device does not remain in Software Product ID mode if powered down. 6. With AMS-A1 = 0; SST Manufacturer's ID = 00BFH, is read with A0 = 0, SST39LF/VF200A Device ID = 2789H, is read with A0 = 1. SST39LF/VF400A Device ID = 2780H, is read with A0 = 1. SST39LF/VF800A Device ID = 2781H, is read with A0 = 1. 7. Both Software ID Exit operations are equivalent TABLE 5: CFI Query Identification String1 for SST39LF200A/400A/800A and SST39VF200A/400A/800A Address 10H 11H 12H 13H 14H 15H 16H 17H 18H 19H 1AH Data 0051H 0052H 0059H 0001H 0007H 0000H 0000H 0000H 0000H 0000H 0000H Data Query Unique ASCII string "QRY" Primary OEM command set Address for Primary Extended Table Alternate OEM command set (00H = none exists) Address for Alternate OEM extended Table (00H = none exits) T5.0 1117 1. Refer to CFI publication 100 for more details. (c)2007 Silicon Storage Technology, Inc. S71117-10-000 8 http://store.iiic.cc/ 08/07 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet TABLE 6: System Interface Information for SST39LF200A/400A/800A and SST39VF200A/400A/800A Address Data 1BH 0027H1 Data VDD Min (Program/Erase) 0030H1 DQ7-DQ4: Volts, DQ3-DQ0: 100 millivolts 1CH 0036H VDD Max (Program/Erase) DQ7-DQ4: Volts, DQ3-DQ0: 100 millivolts 1DH 0000H VPP min (00H = no VPP pin) 1EH 0000H VPP max (00H = no VPP pin) 1FH 0004H Typical time out for Word-Program 2N s (24 = 16 s) 20H 0000H Typical time out for min size buffer program 2N s (00H = not supported) 21H 0004H Typical time out for individual Sector/Block-Erase 2N ms (24 = 16 ms) 22H 0006H Typical time out for Chip-Erase 2N ms (26 = 64 ms) 23H 0001H Maximum time out for Word-Program 2N times typical (21 x 24 = 32 s) 24H 0000H Maximum time out for buffer program 2N times typical 25H 0001H Maximum time out for individual Sector/Block-Erase 2N times typical (21 x 24 = 32 ms) 26H 0001H Maximum time out for Chip-Erase 2N times typical (21 x 26 = 128 ms) T6.2 1117 1. 0030H for SST39LF200A/400A/800A and 0027H for SST39VF200A/400A/800A TABLE 7: Device Geometry Information for SST39LF/VF200A Address 27H 28H 29H 2AH 2BH 2CH 2DH 2EH 2FH 30H 31H 32H 33H 34H Data 0012H 0001H 0000H 0000H Data Device size = 2N Byte (12H = 18; 218 = 256 KByte) Flash Device Interface description; 0001H = x16-only asynchronous interface 0002H 003FH 0000H 0010H 0000H 0003H 0000H 0000H 0001H Number of Erase Sector/Block sizes supported by device Sector Information (y + 1 = Number of sectors; z x 256B = sector size) y = 63 + 1 = 64 sectors (003FH = 63) Maximum number of bytes in multi-byte write = 2N (00H = not supported) z = 16 x 256 Bytes = 4 KByte/sector (0010H = 16) Block Information (y + 1 = Number of blocks; z x 256B = block size) y = 3 + 1 = 4 blocks (0003H = 3) z = 256 x 256 Bytes = 64 KByte/block (0100H = 256) T7.2 1117 (c)2007 Silicon Storage Technology, Inc. S71117-10-000 9 http://store.iiic.cc/ 08/07 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet TABLE 8: Device Geometry Information for SST39LF/VF400A Address 27H 28H 29H 2AH 2BH 2CH 2DH 2EH 2FH 30H 31H 32H 33H 34H Data 0013H 0001H 0000H 0000H 0000H 0002H 007FH 0000H 0010H 0000H 0007H 0000H 0000H 0001H Data Device size = 2N Byte (13H = 19; 219 = 512 KByte) Flash Device Interface description; 0001H = x16-only asynchronous interface Maximum number of bytes in multi-byte write = 2N (00H = not supported) Number of Erase Sector/Block sizes supported by device Sector Information (y + 1 = Number of sectors; z x 256B = sector size) y = 127 + 1 = 128 sectors (007FH = 127) z = 16 x 256 Bytes = 4 KByte/sector (0010H = 16) Block Information (y + 1 = Number of blocks; z x 256B = block size) y = 7 + 1 = 8 blocks (0007H = 7) z = 256 x 256 Bytes = 64 KByte/block (0100H = 256) T8.1 1117 TABLE 9: Device Geometry Information for SST39LF/VF800A Address 27H 28H 29H 2AH 2BH 2CH 2DH 2EH 2FH 30H 31H 32H 33H 34H Data 0014H 0001H 0000H 0000H 0000H 0002H 00FFH 0000H 0010H 0000H 000FH 0000H 0000H 0001H Data Device size = 2N Bytes (14H = 20; 220 = 1 MByte) Flash Device Interface description; 0001H = x16-only asynchronous interface Maximum number of bytes in multi-byte write = 2N (00H = not supported) Number of Erase Sector/Block sizes supported by device Sector Information (y + 1 = Number of sectors; z x 256B = sector size) y = 255 + 1 = 256 sectors (00FFH = 255) z = 16 x 256 Bytes = 4 KByte/sector (0010H = 16) Block Information (y + 1 = Number of blocks; z x 256B = block size) y = 15 + 1 = 16 blocks (000FH = 15) z = 256 x 256 Bytes = 64 KByte/block (0100H = 256) T9.0 1117 (c)2007 Silicon Storage Technology, Inc. S71117-10-000 10 http://store.iiic.cc/ 08/07 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet Absolute Maximum Stress Ratings (Applied conditions greater than those listed under "Absolute Maximum Stress Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these conditions or conditions greater than those defined in the operational sections of this data sheet is not implied. Exposure to absolute maximum stress rating conditions may affect device reliability.) Temperature Under Bias . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55C to +125C Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65C to +150C D. C. Voltage on Any Pin to Ground Potential . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to VDD+0.5V Transient Voltage (<20 ns) on Any Pin to Ground Potential . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -2.0V to VDD+2.0V Voltage on A9 Pin to Ground Potential . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to 13.2V Package Power Dissipation Capability (TA = 25C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.0W Surface Mount Solder Reflow Temperature1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260C for 10 seconds Output Short Circuit Current2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA 1. Excluding certain with-Pb 32-PLCC units, all packages are 260C capable in both non-Pb and with-Pb solder versions. Certain with-Pb 32-PLCC package types are capable of 240C for 10 seconds; please consult the factory for the latest information. 2. Outputs shorted for no more than one second. No more than one output shorted at a time. Operating Range: SST39LF200A/400A/800A Range Ambient Temp VDD 0C to +70C 3.0-3.6V Commercial Operating Range: SST39VF200A/400A/800A Range Ambient Temp VDD 0C to +70C 2.7-3.6V -40C to +85C 2.7-3.6V Commercial Industrial AC Conditions of Test Input Rise/Fall Time . . . . . . . . . . . . . . 5 ns Output Load . . . . . . . . . . . . . . . . . . . . CL = 30 pF for SST39LF200A/400A/800A Output Load . . . . . . . . . . . . . . . . . . . . CL = 100 pF for SST39VF200A/400A/800A See Figures 16 and 17 (c)2007 Silicon Storage Technology, Inc. S71117-10-000 11 http://store.iiic.cc/ 08/07 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet TABLE 10: DC Operating Characteristics VDD = 3.0-3.6V for SST39LF200A/400A/800A and 2.7-3.6V for SST39VF200A/400A/800A1 Limits Symbol Parameter IDD Power Supply Current Min Max Units Test Conditions Address input=VILT/VIHT, at f=1/TRC Min, VDD=VDD Max Read2 30 mA CE#=VIL, OE#=WE#=VIH, all I/Os open Program and Erase 30 mA CE#=WE#=VIL, OE#=VIH ISB Standby VDD Current 20 A CE#=VIHC, VDD=VDD Max ILI Input Leakage Current 1 A VIN=GND to VDD, VDD=VDD Max ILO Output Leakage Current 10 A VIL Input Low Voltage 0.8 VIH Input High Voltage 0.7VDD V VDD=VDD Max VIHC Input High Voltage (CMOS) VDD-0.3 V VDD=VDD Max VOL Output Low Voltage VOH Output High Voltage 0.2 VDD-0.2 VOUT=GND to VDD, VDD=VDD Max VDD=VDD Min V IOL=100 A, VDD=VDD Min V IOH=-100 A, VDD=VDD Min T10.7 1117 1. Typical conditions for the Active Current shown on page 1 are average values at 25C (room temperature), and VDD = 3V for VF devices. Not 100% tested. 2. Values are for 70 ns conditions. See the Multi-Purpose Flash Power Rating application note for further information. TABLE 11: Recommended System Power-up Timings Symbol TPU-READ Parameter 1 TPU-WRITE1 Minimum Units Power-up to Read Operation 100 s Power-up to Program/Erase Operation 100 s T11.0 1117 1. This parameter is measured only for initial qualification and after a design or process change that could affect this parameter. TABLE 12: Capacitance (TA = 25C, f=1 Mhz, other pins open) Parameter Description Test Condition Maximum CI/O1 I/O Pin Capacitance VI/O = 0V 12 pF Input Capacitance VIN = 0V 6 pF CIN 1 T12.0 1117 1. This parameter is measured only for initial qualification and after a design or process change that could affect this parameter. TABLE 13: Reliability Characteristics Symbol NEND 1,2 Parameter Minimum Specification Units Endurance 10,000 Cycles JEDEC Standard A117 100 Years JEDEC Standard A103 100 + IDD mA JEDEC Standard 78 TDR1 Data Retention ILTH1 Latch Up Test Method T13.2 1117 1. This parameter is measured only for initial qualification and after a design or process change that could affect this parameter. 2. NEND endurance rating is qualified as a 10,000 cycle minimum for the whole device. A sector- or block-level rating would result in a higher minimum specification. (c)2007 Silicon Storage Technology, Inc. S71117-10-000 12 http://store.iiic.cc/ 08/07 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet AC CHARACTERISTICS TABLE 14: Read Cycle Timing Parameters VDD = 3.0-3.6V SST39LF200A-45 Min Max SST39LF200A/400A/800A-55 Symbol Parameter Max Units TRC Read Cycle Time TCE Chip Enable Access Time 45 55 ns TAA TOE Address Access Time 45 55 ns Output Enable Access Time 30 30 TCLZ1 TOLZ1 TCHZ1 TOHZ1 TOH1 ns CE# Low to Active Output 0 0 ns OE# Low to Active Output 0 0 ns 45 Min 55 ns CE# High to High-Z Output 15 15 ns OE# High to High-Z Output 15 15 ns Output Hold from Address Change 0 0 ns T14.7 1117 1. This parameter is measured only for initial qualification and after a design or process change that could affect this parameter. TABLE 15: Read Cycle Timing Parameters VDD = 2.7-3.6V SST39VF200A/400A/800A-70 Symbol Parameter Min Max Units TRC Read Cycle Time TCE Chip Enable Access Time 70 ns TAA Address Access Time 70 ns TOE Output Enable Access Time 35 ns TCLZ1 TOLZ1 TCHZ1 TOHZ1 TOH1 CE# Low to Active Output 0 ns OE# Low to Active Output 0 ns 70 ns CE# High to High-Z Output 20 ns OE# High to High-Z Output 20 ns Output Hold from Address Change 0 ns T15.7 1117 1. This parameter is measured only for initial qualification and after a design or process change that could affect this parameter. (c)2007 Silicon Storage Technology, Inc. S71117-10-000 13 http://store.iiic.cc/ 08/07 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet TABLE 16: Program/Erase Cycle Timing Parameters Symbol Parameter TBP Word-Program Time TAS Address Setup Time 0 ns TAH Address Hold Time 30 ns TCS WE# and CE# Setup Time 0 ns TCH WE# and CE# Hold Time 0 ns TOES OE# High Setup Time 0 ns TOEH OE# High Hold Time 10 ns TCP CE# Pulse Width 40 ns TWP WE# Pulse Width 40 ns TWPH1 WE# Pulse Width High 30 ns TCPH1 CE# Pulse Width High 30 ns TDS Data Setup Time 30 ns TDH1 Data Hold Time 0 ns TIDA 1 Min Max Units 20 s Software ID Access and Exit Time 150 ns TSE Sector-Erase 25 ms TBE Block-Erase 25 ms TSCE Chip-Erase 100 ms T16.0 1117 1. This parameter is measured only for initial qualification and after a design or process change that could affect this parameter. (c)2007 Silicon Storage Technology, Inc. S71117-10-000 14 http://store.iiic.cc/ 08/07 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet TRC TAA ADDRESS AMS-0 TCE CE# TOE OE# TOHZ TOLZ VIH WE# TCLZ HIGH-Z DQ15-0 Note: TCHZ TOH DATA VALID HIGH-Z DATA VALID AMS = Most significant address AMS = A16 for SST39LF/VF200A, A17 for SST39LF/VF400A and A18 for SST39LF/VF800A 1117 F03.2 FIGURE 5: Read Cycle Timing Diagram INTERNAL PROGRAM OPERATION STARTS TBP 5555 ADDRESS AMS-0 2AAA 5555 ADDR TAH TDH TWP WE# TDS TWPH TAS OE# TCH CE# TCS DQ15-0 Note: XXAA XX55 XXA0 DATA SW0 SW1 SW2 WORD (ADDR/DATA) AMS = Most significant address AMS = A16 for SST39LF/VF200A, A17 for SST39LF/VF400A and A18 for SST39LF/VF800A X can be VIL or VIH, but no other value. 1117 F04.4 FIGURE 6: WE# Controlled Program Cycle Timing Diagram (c)2007 Silicon Storage Technology, Inc. S71117-10-000 15 http://store.iiic.cc/ 08/07 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet INTERNAL PROGRAM OPERATION STARTS TBP 5555 ADDRESS AMS-0 2AAA 5555 ADDR TAH TDH TCP CE# TCPH TAS TDS OE# TCH WE# TCS DQ15-0 Note: XXAA XX55 XXA0 DATA SW0 SW1 SW2 WORD (ADDR/DATA) AMS = Most significant address AMS = A16 for SST39LF/VF200A, A17 for SST39LF/VF400A and A18 for SST39LF/VF800A X can be VIL or VIH, but no other value. 1117 F05.4 FIGURE 7: CE# Controlled Program Cycle Timing Diagram ADDRESS AMS-0 TCE CE# TOEH TOES OE# TOE WE# DATA DQ7 Note: DATA# DATA# DATA AMS = Most significant address AMS = A16 for SST39LF/VF200A, A17 for SST39LF/VF400A and A18 for SST39LF/VF800A 1117 F06.3 FIGURE 8: Data# Polling Timing Diagram (c)2007 Silicon Storage Technology, Inc. S71117-10-000 16 http://store.iiic.cc/ 08/07 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet ADDRESS AMS-0 TCE CE# TOEH TOE TOES OE# WE# DQ6 TWO READ CYCLES WITH SAME OUTPUTS Note: AMS = Most significant address AMS = A16 for SST39LF/VF200A, A17 for SST39LF/VF400A and A18 for SST39LF/VF800A 1117 F07.3 FIGURE 9: Toggle Bit Timing Diagram TSCE SIX-BYTE CODE FOR CHIP-ERASE ADDRESS AMS-0 5555 2AAA 5555 5555 2AAA 5555 CE# OE# TWP WE# DQ15-0 XXAA SW0 XX55 SW1 XX80 SW2 XXAA SW3 XX55 SW4 XX10 SW5 Note: This device also supports CE# controlled Chip-Erase operation. The WE# and CE# signals are interchageable as long as minimum timings are met. (See Table 16) AMS = Most significant address AMS = A16 for SST39LF/VF200A, A17 for SST39LF/VF400A and A18 for SST39LF/VF800A X can be VIL or VIH, but no other value. 1117 F08.7 FIGURE 10: WE# Controlled Chip-Erase Timing Diagram (c)2007 Silicon Storage Technology, Inc. S71117-10-000 17 http://store.iiic.cc/ 08/07 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet TBE SIX-BYTE CODE FOR BLOCK-ERASE ADDRESS AMS-0 5555 2AAA 5555 5555 2AAA BAX CE# OE# TWP WE# DQ15-0 XXAA XX55 XX80 XXAA XX55 XX50 SW0 SW1 SW2 SW3 SW4 SW5 Note: This device also supports CE# controlled Block-Erase operation. The WE# and CE# signals are interchageable as long as minimum timings are met. (See Table 16) BAX = Block Address AMS = Most significant address AMS = A16 for SST39LF/VF200A, A17 for SST39LF/VF400A and A18 for SST39LF/VF800A X can be VIL or VIH, but no other value. 1117 F17.9 FIGURE 11: WE# Controlled Block-Erase Timing Diagram TSE SIX-BYTE CODE FOR SECTOR-ERASE ADDRESS AMS-0 5555 2AAA 5555 5555 2AAA SAX CE# OE# TWP WE# DQ15-0 XXAA XX55 XX80 XXAA XX55 XX30 SW0 SW1 SW2 SW3 SW4 SW5 Note: This device also supports CE# controlled Sector-Erase operation. The WE# and CE# signals are interchageable as long as minimum timings are met. (See Table 16) SAX = Sector Address AMS = Most significant address AMS = A16 for SST39LF/VF200A, A17 for SST39LF/VF400A and A18 for SST39LF/VF800A X can be VIL or VIH, but no other value. 1117 F18.8 FIGURE 12: WE# Controlled Sector-Erase Timing Diagram (c)2007 Silicon Storage Technology, Inc. S71117-10-000 18 http://store.iiic.cc/ 08/07 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet THREE-BYTE SEQUENCE FOR SOFTWARE ID ENTRY ADDRESS A14-0 5555 2AAA 5555 0000 0001 CE# OE# TWP TIDA WE# TWPH DQ15-0 XXAA SW0 XX55 SW1 TAA XX90 SW2 00BF Device ID Device ID = 2789H for SST39LF/VF200A, 2780H for SST39LF/VF400A and 2781H for SST39LF/VF800A Note: X can be VIL or VIH, but no other value. 1117 F09.4 FIGURE 13: Software ID Entry and Read THREE-BYTE SEQUENCE FOR CFI QUERY ENTRY ADDRESS A14-0 5555 2AAA 5555 CE# OE# TIDA TWP WE# TAA TWPH DQ15-0 XXAA SW0 XX55 SW1 XX98 SW2 Note: X can be VIL or VIH, but no other value. 1117 F20.1 FIGURE 14: CFI Query Entry and Read (c)2007 Silicon Storage Technology, Inc. S71117-10-000 19 http://store.iiic.cc/ 08/07 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet THREE-BYTE SEQUENCE FOR SOFTWARE ID EXIT AND RESET ADDRESS A14-0 5555 DQ15-0 2AAA XXAA 5555 XX55 XXF0 TIDA CE# OE# TWP TWHP WE# SW0 Note: SW1 SW2 X can be VIL or VIH, but no other value. 1117 F10.1 FIGURE 15: Software ID Exit/CFI Exit (c)2007 Silicon Storage Technology, Inc. S71117-10-000 20 http://store.iiic.cc/ 08/07 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet VIHT VIT INPUT REFERENCE POINTS VOT OUTPUT VILT 1117 F11.1 AC test inputs are driven at VIHT (0.9 VDD) for a logic "1" and VILT (0.1 VDD) for a logic "0". Measurement reference points for inputs and outputs are VIT (0.5 VDD) and VOT (0.5 VDD). Input rise and fall times (10% 90%) are <5 ns. Note: VIT - VINPUT Test VOT - VOUTPUT Test VIHT - VINPUT HIGH Test VILT - VINPUT LOW Test FIGURE 16: AC Input/Output Reference Waveforms TO TESTER TO DUT CL 1117 F12.1 FIGURE 17: A Test Load Example (c)2007 Silicon Storage Technology, Inc. S71117-10-000 21 http://store.iiic.cc/ 08/07 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet Start Load data: XXAAH Address: 5555H Load data: XX55H Address: 2AAAH Load data: XXA0H Address: 5555H Load Word Address/Word Data Wait for end of Program (TBP, Data# Polling bit, or Toggle bit operation) Program Completed Note: X can be VIL or VIH, but no other value. 1117 F13.4 FIGURE 18: Word-Program Algorithm (c)2007 Silicon Storage Technology, Inc. S71117-10-000 22 http://store.iiic.cc/ 08/07 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet Internal Timer Toggle Bit Data# Polling Program/Erase Initiated Program/Erase Initiated Program/Erase Initiated Wait TBP, TSCE, TSE or TBE Read word Read DQ7 Read same word Program/Erase Completed No Is DQ7 = true data? Yes No Does DQ6 match? Program/Erase Completed Yes Program/Erase Completed 1117 F14.0 FIGURE 19: Wait Options (c)2007 Silicon Storage Technology, Inc. S71117-10-000 23 http://store.iiic.cc/ 08/07 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet CFI Query Entry Command Sequence Software ID Entry Command Sequence Software ID Exit/CFI Exit Command Sequence Load data: XXAAH Address: 5555H Load data: XXAAH Address: 5555H Load data: XXAAH Address: 5555H Load data: XXF0H Address: XXH Load data: XX55H Address: 2AAAH Load data: XX55H Address: 2AAAH Load data: XX55H Address: 2AAAH Wait TIDA Load data: XX98H Address: 5555H Load data: XX90H Address: 5555H Load data: XXF0H Address: 5555H Return to normal operation Wait TIDA Wait TIDA Wait TIDA Read CFI data Read Software ID Return to normal operation 1117 F15.4 Note: X can be VIL or VIH, but no other value. FIGURE 20: Software ID/CFI Command Flowcharts (c)2007 Silicon Storage Technology, Inc. S71117-10-000 24 http://store.iiic.cc/ 08/07 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet Chip-Erase Command Sequence Sector-Erase Command Sequence Block-Erase Command Sequence Load data: XXAAH Address: 5555H Load data: XXAAH Address: 5555H Load data: XXAAH Address: 5555H Load data: XX55H Address: 2AAAH Load data: XX55H Address: 2AAAH Load data: XX55H Address: 2AAAH Load data: XX80H Address: 5555H Load data: XX80H Address: 5555H Load data: XX80H Address: 5555H Load data: XXAAH Address: 5555H Load data: XXAAH Address: 5555H Load data: XXAAH Address: 5555H Load data: XX55H Address: 2AAAH Load data: XX55H Address: 2AAAH Load data: XX55H Address: 2AAAH Load data: XX10H Address: 5555H Load data: XX30H Address: SAX Load data: XX50H Address: BAX Wait TSCE Wait TSE Wait TBE Chip erased to FFFFH Sector erased to FFFFH Block erased to FFFFH Note: X can be VIL or VIH, but no other value. 1117 F16.5 FIGURE 21: Erase Command Sequence (c)2007 Silicon Storage Technology, Inc. S71117-10-000 25 http://store.iiic.cc/ 08/07 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet PRODUCT ORDERING INFORMATION SST 39 XX VF 200A XX XXXX - 70 - XXX - 4C XX - B3K - XXX E X Environmental Attribute E1 = non-Pb Package Modifier K = 48 leads or balls Q = 48 balls or bumps (66 possible positions) Package Type B3 = TFBGA (0.8mm pitch, 6mm x 8mm) C1 = XFLGA (0.5mm pitch, 4mm x 6mm) E = TSOP (type 1, die up, 12mm x 20mm) M1 = WFBGA (0.5mm pitch, 4mm x 6mm) Y1 = WFBGA (panel-based, 0.5mm pitch, 4mm x 6mm)" Temperature Range C = Commercial = 0C to +70C I = Industrial = -40C to +85C Minimum Endurance 4 = 10,000 cycles Read Access Speed 45 = 45 ns 55 = 55 ns 70 = 70 ns Version A = Special Feature Version Device Density 800 = 8 Mbit 400 = 4 Mbit 200 = 2 Mbit Voltage L = 3.0-3.6V V = 2.7-3.6V Product Series 39 = Multi-Purpose Flash 1. Environmental suffix "E" denotes non-Pb solder. SST non-Pb solder devices are "RoHS Compliant". (c)2007 Silicon Storage Technology, Inc. S71117-10-000 26 http://store.iiic.cc/ 08/07 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet Valid combinations for SST39LF200A SST39LF200A-45-4C-EKE SST39LF200A-55-4C-EKE SST39LF200A-45-4C-B3KE SST39LF200A-55-4C-B3KE Valid combinations for SST39VF200A SST39VF200A-70-4C-EKE SST39VF200A-70-4C-B3KE SST39VF200A-70-4C-M1QE SST39VF200A-70-4C-Y1QE SST39VF200A-70-4I-EKE SST39VF200A-70-4I-B3KE SST39VF200A-70-4I-M1QE SST39VF200A-70-4I-Y1QE Valid combinations for SST39LF400A SST39LF400A-55-4C-EKE SST39LF400A-55-4C-B3KE Valid combinations for SST39VF400A SST39VF400A-70-4C-EKE SST39VF400A-70-4C-B3KE SST39VF400A-70-4C-C1QE SST39VF400A-70-4C-M1QE SST39VF400A-70-4I-EKE SST39VF400A-70-4I-M1QE SST39VF400A-70-4I-B3KE SST39VF400A-70-4I-C1QE Valid combinations for SST39LF800A SST39LF800A-55-4C-EKE SST39LF800A-55-4C-B3KE Valid combinations for SST39VF800A SST39VF800A-70-4C-EKE SST39VF800A-70-4C-B3KE SST39VF800A-70-4C-C1QE SST39VF800A-70-4C-Y1QE SST39VF800A-70-4C-M1QE SST39VF800A-70-4I-EKE SST39VF800A-70-4I-B3KE SST39VF800A-70-4I-Y1QE SST39VF800A-70-4I-M1QE SST39VF800A-70-4I-C1QE Note: Valid combinations are those products in mass production or will be in mass production. Consult your SST sales representative to confirm availability of valid combinations and to determine availability of new combinations. (c)2007 Silicon Storage Technology, Inc. S71117-10-000 27 http://store.iiic.cc/ 08/07 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet PACKAGING DIAGRAMS 1.05 0.95 Pin # 1 Identifier 0.50 BSC 0.27 0.17 12.20 11.80 0.15 0.05 18.50 18.30 DETAIL 1.20 max. 0.70 0.50 20.20 19.80 0- 5 Note: 1. Complies with JEDEC publication 95 MO-142 DD dimensions, although some dimensions may be more stringent. 2. All linear dimensions are in millimeters (max/min). 3. Coplanarity: 0.1 mm 4. Maximum allowable mold flash is 0.15 mm at the package ends, and 0.25 mm between leads. 0.70 0.50 1mm 48-tsop-EK-8 FIGURE 22: 48-Lead Thin Small Outline Package (TSOP) 12mm x 20mm SST Package Code: EK (c)2007 Silicon Storage Technology, Inc. S71117-10-000 28 http://store.iiic.cc/ 08/07 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet TOP VIEW BOTTOM VIEW 8.00 0.20 5.60 0.45 0.05 (48X) 0.80 6 6 5 5 4.00 4 4 6.00 0.20 3 3 2 2 1 1 0.80 A B C D E F G H A1 CORNER SIDE VIEW H G F E D C B A A1 CORNER 1.10 0.10 0.12 SEATING PLANE 1mm 0.35 0.05 Note: 1. Complies with JEDEC Publication 95, MO-210, variant 'AB-1', although some dimensions may be more stringent. 2. All linear dimensions are in millimeters. 3. Coplanarity: 0.12 mm 4. Ball opening size is 0.38 mm ( 0.05 mm) 48-tfbga-B3K-6x8-450mic-4 FIGURE 23: 48-Ball Thin-Profile, Fine-pitch Ball Grid Array (TFBGA) 6mm x 8mm SST Package Code: B3K TOP VIEW BOTTOM VIEW 6.00 0.08 5.00 0.32 0.05 (48X) 0.50 6 5 4 3 2 1 4.00 0.08 6 5 4 3 2 1 2.50 0.50 A B C D E F G H J K L L K J H G F E D C B A A1 INDICATOR4 A1 CORNER 0.63 0.10 DETAIL SIDE VIEW 0.08 SEATING PLANE 0.20 0.06 Note: 1. 2. 3. 4. 5. 1mm Complies with JEDEC Publication 95, MO-207, Variant C2B-4, dimensions except nominal ball width is larger. All linear dimensions are in millimeters. Coplanarity: 0.08 mm. No ball is present in position A1; a gold-colored indicator is present. Ball opening size is 0.29 mm ( 0.05 mm). 48-wfbga-M1Q-4x6-32mic-6.0 FIGURE 24: 48-Ball Very-Very-Thin-Profile, Fine-Pitch Ball Grid Array (WFBGA) 4mm x 6mm SST Package Code: M1Q (c)2007 Silicon Storage Technology, Inc. S71117-10-000 29 http://store.iiic.cc/ 08/07 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet TOP VIEW BOTTOM VIEW 6.00 0.08 5.00 0.29 0.05 (48X) 0.50 6 5 4 3 2 1 4.00 0.08 6 5 4 3 2 1 2.50 0.50 A B C D E F G H J K L L K J H G F E D C B A A1 INDICATOR4 A1 CORNER 0.52 max. 0.473 nom. DETAIL SIDE VIEW 0.05 SEATING PLANE 1mm 0.04 +0.025/-0.015 Note: 1. 2. 3. 4. 5. Complies with JEDEC Publication 95, MO-207, variant CZB-4, dimensions except bump height is much less. All linear dimensions are in millimeters. Coplanarity: 0.05 mm. No ball is present at A1; a gold-colored indicator is present. 48-xflga-C1Q-4x6-29mic-6.0 Bump opening size is 0.29 (0.05 mm). FIGURE 25: 48-Bump Extremely-Thin-Profile, Fine-Pitch Land Grid Array (XFLGA) 4mm x 6mm SST Package Code: C1Q TOP VIEW BOTTOM VIEW 6.00 0.08 5.00 0.50 6 5 4 3 2 1 4.00 0.08 2.50 0.50 A B C D E F G H J K L L K J H G F E D C B A 4 A1 CORNER DETAIL 6 5 4 3 2 1 0.32 0.05 (48X) A1 INDICATOR SIDE VIEW 0.61 0.10 0.08 SEATING PLANE 0.23 0.06 Note: 1mm 1. Complies with JEDEC Publication 95, MO-207, variant CZB-4, dimensions except nominal ball width is larger. 2. All linear dimensions are in millimeters. 3. Coplanarity: 0.08 mm 4. No ball is present in position A1; a gold-colored indicator is present. 5. Ball width at interface to package body surface is 0.29 mm. 48-wfbga-Y1Q-4x6-320mic-5-2.0 FIGURE 26: 48-Ball Very-Very-Thin-Profile, Fine-Pitch Ball Grid Array (WFBGA) 4mm x 6mm (Panel-based) SST Package Code: Y1Q (c)2007 Silicon Storage Technology, Inc. S71117-10-000 30 http://store.iiic.cc/ 08/07 2 Mbit / 4 Mbit / 8 Mbit Multi-Purpose Flash SST39LF200A / SST39LF400A / SST39LF800A SST39VF200A / SST39VF400A / SST39VF800A Data Sheet TABLE 17: Revision History Number Description Date 04 * 2002 Data Book May 2002 05 * * Mar 2003 * * Added footnotes for MPF power usage and Typical conditions to Table 10 on page 12 Clarified the Test Conditions for Power Supply Current and Read parameters in Table 10 on page 12 Part number changes - see page 27 for additional information New Micro-Package part numbers added for SST39VF400A and SST39VF800A 06 * New Micro-Package part numbers added for SST39VF400A / 800A (see page 27) Oct 2003 07 * * * 2004 Data Book Updated the B3K, M1Q, and C1Q package diagrams Added non-Pb MPNs and removed footnote (see page 27) Nov 2003 08 * * * Added M1Q/M1QE MPNs for the SSTVF200A device on page 27 Removed 90ns MPNs and footnote for the SSTVFx00A devices on page 27 Added RoHS compliance information on page 1 and in the "Product Ordering Information" on page 26 Clarified the solder temperature profile under "Absolute Maximum Stress Ratings" on page 11. Apr 2005 Feb 2007 * Removed valid combinations SST39LF400A-45-4C-EK, SST39LF400A-45-4C-B3K, SST39LF400A-45-4C-EKE, and SST39LF400A-45-4C-B3KE due to EOL Applied new format styles. * * Add Y1QE package Removed all pb parts Aug 2007 * 09 10 * Silicon Storage Technology, Inc. * 1171 Sonora Court * Sunnyvale, CA 94086 * Telephone 408-735-9110 * Fax 408-735-9036 www.SuperFlash.com or www.sst.com (c)2007 Silicon Storage Technology, Inc. S71117-10-000 31 http://store.iiic.cc/ 08/07