NC7SV08 TinyLogic(R) ULP-A 2-Input AND Gate Features Description 0.9V to 3.6V VCC Supply Operation Extremely High Speed tPD - 1.0ns: Typical for 2.7V to 3.6V VCC - 1.2ns: Typical for 2.3V to 2.7V VCC - 2.0ns: Typical for 1.65V to 1.95V VCC - 3.2ns: Typical for 1.4V to 1.6V VCC - 6.0ns: Typical for 1.1V to 1.3V VCC - 13.0ns: Typical for 0.9V VCC The NC7SV08 is a single two-input AND gate from Fairchild's Ultra-Low Power (ULP-A) Series of (R) TinyLogic . ULP-A is ideal for applications that require extreme high speed, high drive, and low power. This product is designed for a wide low-voltage operating range (0.9V to 3.6V VCC) and applications that require (R) more drive and speed than the TinyLogic ULP series, but still offer best-in-class, low-power operation. 3.6V Over-Voltage Tolerant I/Os at VCC from 0.9V to 3.6V The NC7SV08 is uniquely designed for optimized power and speed and is fabricated with an advanced CMOS technology to achieve high-speed operation while maintaining low CMOS power dissipation. Power-Off High-Impedance Inputs and Outputs High Static Drive (IOH/IOL) - 24mA at 3.00V VCC - 18mA at 2.30V VCC - 6mA at 1.65V VCC - 4mA at 1.4V VCC - 2mA at 1.1V VCC - 0.1mA at 0.9V VCC Uses Proprietary Quiet SeriesTM Noise/EMI Reduction Circuitry Ultra-Small MicroPakTM Packages Ultra-Low Dynamic Power Ordering Information Part Number Top Mark Package Packing Method NC7SV08P5X V08 5-Lead SC70, EIAJ SC-88a, 1.25mm Wide 3000 Units on Tape & Reel NC7SV08L6X G3 6-Lead MicroPakTM, 1.00mm Wide 5000 Units on Tape & Reel NC7SV08FHX G3 6-Lead, MicroPak2, 1x1mm Body, .35mm Pitch 5000 Units on Tape & Reel TinyLogic(R) is a registered trademark of Fairchild Semiconductor Corporation. MicroPakTM and Quiet SeriesTM are trademarks of Fairchild Semiconductor Corporation. (c) 2002 Fairchild Semiconductor Corporation NC7SV08 * Rev. 1.0.4 www.fairchildsemi.com NC7SV08 -- TinyLogic(R) ULP-A 2-Input AND Gate September 2010 Figure 1. Battery Life vs. VCC Supply Voltage Notes: (R) 1. TinyLogic ULP and ULP-A with up to 50% less power consumption can extend battery life significantly. Battery Life = (Vbattery*Ibattery*.9)/(Pdevice)/24hrs/day where, Pdevice = (ICC * VCC) + (CPD + CL) * VCC2 * f. 2. Assumes ideal 3.6V Lithium Ion battery with current rating of 900mAH and derated 90% and device frequency at 10MHz, with CL = 15pF load. NC7SV08 -- TinyLogic(R) ULP-A 2-Input AND Gate Battery Life Connection Diagram IEEE/IEC A B & Figure 2. (c) 2002 Fairchild Semiconductor Corporation NC7SV08 * Rev. 1.0.4 Y Logic Symbol www.fairchildsemi.com 2 A 1 B 2 GND 3 5 4 Figure 3. VCC Y SC70 (Top View) A 1 6 VCC B 2 5 NC GND 3 4 Y Figure 4. MicroPak (Top Through View) Pin Definitions Pin # SC70 Pin # MicroPak Name 1 1 A Input 2 2 B Input 3 3 GND Ground 4 4 Y Output 5 NC No Connect 6 VCC Supply Voltage 5 Description NC7SV08 -- TinyLogic(R) ULP-A 2-Input AND Gate Pin Configurations Function Table Inputs Output A B Y L L L L H L H L L H H H H = HIGH Logic Level L = LOW Logic Level (c) 2002 Fairchild Semiconductor Corporation NC7SV08 * Rev. 1.0.4 www.fairchildsemi.com 3 Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. Symbol Parameter Min. Max. Unit VCC Supply Voltage -0.5 4.6 V VIN DC Input Voltage -0.5 4.6 V -0.5 VCC + 0.5 -0.5 4.6 VOUT IIK DC Input Diode Current IOK DC Output Diode Current IOH/IOL ICC or IGND TSTG HIGH or LOW State DC Output Voltage (3) VCC = 0V VIN < 0V -50 VOUT < 0V -50 VOUT > VCC +50 V mA mA DC Output Source/Sink Current 50 mA DC VCC or Ground Current per Supply Pin 50 mA +150 C TJ Junction Temperature Under Bias +150 C TL Junction Lead Temperature, Soldering 10 Seconds +260 C PD ESD Storage Temperature Range Power Dissipation at +85C -65 SC70-5 150 MicroPak-6 130 MicroPak2-6 120 Human Body Model, JEDEC:JESD22-A114 4000 Charge Device Model, JEDEC:JESD22-C101 2000 NC7SV08 -- TinyLogic(R) ULP-A 2-Input AND Gate Absolute Maximum Ratings mW V Note: 3. IO absolute maximum rating must be observed. Recommended Operating Conditions The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not recommend exceeding them or designing to Absolute Maximum Ratings. Symbol Parameter VCC Supply Voltage VIN Input Voltage VOUT IOH/IOL Output Voltage Output Current in IOH/IOL Conditions Min. Max. Unit 0.9 3.6 V V 0 3.6 VCC = 0V 0 3.6 HIGH or LOW State 0 VCC VCC = 3.0V to 3.6V 24 VCC = 2.3V to 3.6V 18 VCC = 1.65V to 1.95V 6 VCC = 1.4V to 1.6V 4 VCC = 1.1V to 1.3V t/V JA Operating Temperature, Free Air Minimum Input Edge Rate Thermal Resistance mA 2 VCC = 0.9V TA V 0.1 -40 +85 C VIN = 0.8V to 2.0, VCC = 3.0V 10 ns/V SC70-5 425 MicroPak-6 500 MicroPak2-6 560 C/W Note: 4. Unused inputs must be held HIGH or LOW. They may not float. (c) 2002 Fairchild Semiconductor Corporation NC7SV08 * Rev. 1.0.4 www.fairchildsemi.com 4 Symbol VIH VIL Parameter VCC TA=25C Min. Max. Min. .65 x VCC .65 x VCC 1.10 VCC 1.30 .65 x VCC .65 x VCC 1.40 VCC 1.60 .65 x VCC .65 x VCC 1.65 VCC 1.95 .65 x VCC .65 x VCC 2.30 VCC 2.70 1.6 1.6 2.70 VCC 3.60 2.0 2.0 Max. 0.90 .35 x VCC .35 x VCC .35 x VCC .35 x VCC 1.40 VCC 1.60 .35 x VCC .35 x VCC 1.65 VCC 1.95 .35 x VCC .35 x VCC 2.30 VCC 2.70 0.7 0.7 VCC-0.1 1.10 VCC 1.30 VCC-0.1 1.40 VCC 1.60 VCC-0.2 VCC-0.2 VCC-0.2 VCC-0.2 2.30 VCC 2.70 VCC-0.2 VCC-0.2 2.70 VCC 3.60 VCC-0.2 VCC-0.2 IOH=-100A VCC-0.1 VCC-0.1 1.10 VCC 1.30 IOH=-2mA .75 x VCC .75 x VCC 1.40 VCC 1.60 IOH=-4mA .75 x VCC .75 x VCC 1.65 VCC 1.95 2.30 VCC 2.70 2.30 VCC 2.70 2.70 VCC 3.60 2.30 VCC 2.70 2.70 VCC 3.60 IOH=-6mA IOH=-12mA IOH=-18mA 2.70 VCC 3.60 IOH=-24mA 1.25 1.25 2.00 2.00 1.8 1.8 2.2 2.2 1.7 1.7 2.4 2.4 2.2 V 0.8 0.90 1.65 VCC 1.95 HIGH Level Output Voltage 0.8 Units V 1.10 VCC 1.30 2.70 VCC 3.60 VOH TA=-40 to 85C 0.90 HIGH Level Input Voltage LOW Level Input Voltage Conditions NC7SV08 -- TinyLogic(R) ULP-A 2-Input AND Gate DC Electrical Characteristics V 2.2 Continued on following page... (c) 2002 Fairchild Semiconductor Corporation NC7SV08 * Rev. 1.0.4 www.fairchildsemi.com 5 Symbol Parameter VCC LOW Level Output Voltage Min. ICC Quiescent Supply Current Units 0.1 0.1 1.40 VCC 1.60 0.2 0.2 0.2 0.2 2.30 VCC 2.70 0.2 0.2 2.70 VCC 3.60 0.2 0.2 1.10 VCC 1.30 IOL=2mA 0.25 x VCC 0.25 x VCC 1.40 VCC 1.60 IOL=4mA 0.25 x VCC 0.25 x VCC 1.65 VCC 1.95 IOL=6mA 0.3 0.3 2.30 VCC 2.70 0.4 0.4 0.4 0.4 0.6 0.6 0.4 0.4 0.55 0.55 0 VIN 3.60 0.1 0.5 A 0 (VIN, vO) 3.60 0.5 0.5 A VIN=VCC, or GND 0.9 0.9 IOL=100A IOL=12mA IOL=18mA 2.70 VCC 3.60 IOL=24mA Power Off Leakage Current Max. 1.10 VCC 1.30 2.30 VCC 2.70 IOFF Min. 0.1 2.70 VCC 3.60 IIN Max. 0.1 2.70 VCC 3.60 Input Leakage Current TA=-40 to 85C 0.90 1.65 VCC 1.95 VOL TA=25C Conditions 0.90 to 3.60 0 0.90 to 3.60 VCC VIN 3.6V 0.9 V NC7SV08 -- TinyLogic(R) ULP-A 2-Input AND Gate DC Electrical Characteristics (Continued) A AC Electrical Characteristics Symbol Parameter Conditions 0.90 CL=15pF, RL=1M 1.10 VCC 1.30 tPHL, tPLH Propagation Delay TA=25C VCC 1.40 VCC 1.60 CL=15pF, RL=2k 1.65 VCC 1.95 2.30 VCC 2.70 CL=30pF, RL=500 2.70 VCC 3.60 CIN Input Capacitance 0 CPD Power Dissipation Capacitance 0.90 to 3.60 (c) 2002 Fairchild Semiconductor Corporation NC7SV08 * Rev. 1.0.4 VIN=0V or VCC, f=10MHz Min. Typ. 3.0 6.0 TA=-40 to 85C Max. Min. Max. 10.0 1.0 14.6 Units Figure 13 1.0 3.2 6.0 1.0 7.2 1.0 2.0 4.5 1.0 5.3 0.8 1.2 2.6 0.7 3.7 0.7 1.0 2.3 0.6 3.0 ns 2 pF 8 pF Figure 5 Figure 6 www.fairchildsemi.com 6 NC7SV08 -- TinyLogic(R) ULP-A 2-Input AND Gate AC Loadings and Waveforms Figure 5. AC Test Circuit Figure 6. AC Waveforms VCC Symbol 3.3V 0.3V 2.5V 0.2V 1.8V 0.15V 1.5V 0.1V 1.2V 0.1V 0.9V Vmi 1.5V VCC/2 VCC/2 VCC/2 VCC/2 VCC/2 Vmo 1.5V VCC/2 VCC/2 VCC/2 VCC/2 VCC/2 (c) 2002 Fairchild Semiconductor Corporation NC7SV08 * Rev. 1.0.4 www.fairchildsemi.com 7 NC7SV08 -- TinyLogic(R) ULP-A 2-Input AND Gate Physical Dimensions Figure 7. 5-Lead, SC70, EIAJ SC-88a, 1.25mm Wide Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild's worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor's online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/. Tape and Reel Specification Please visit Fairchild Semiconductor's online packaging area for the most recent tape and reel specifications: http://www.fairchildsemi.com/products/analog/pdf/sc70-5_tr.pdf. Package Designator P5X (c) 2002 Fairchild Semiconductor Corporation NC7SV08 * Rev. 1.0.4 Tape Section Cavity Number Cavity Status Cover Type Status Leader (Start End) 125 (Typical) Empty Sealed Carrier 3000 Filled Sealed Trailer (Hub End) 75 (Typical) Empty Sealed www.fairchildsemi.com 8 NC7SV08 -- TinyLogic(R) ULP-A 2-Input AND Gate Physical Dimensions 2X 0.05 C 1.45 B 2X (1) 0.05 C (0.254) (0.49) 5X 1.00 (0.75) PIN 1 IDENTIFIER 5 (0.52) 1X A TOP VIEW 0.55MAX (0.30) 6X PIN 1 0.05 C 0.05 0.00 RECOMMENED LAND PATTERN 0.05 C C 0.25 6X 0.15 1.0 DETAIL A 0.10 0.05 0.45 0.35 0.10 0.00 6X C B A C 0.40 0.30 0.35 5X 0.25 0.40 5X 0.30 0.5 (0.05) 6X DETAIL A PIN 1 TERMINAL 0.075 X 45 CHAMFER (0.13) 4X BOTTOM VIEW Notes: 1. CONFORMS TO JEDEC STANDARD M0-252 VARIATION UAAD 2. DIMENSIONS ARE IN MILLIMETERS 3. DRAWING CONFORMS TO ASME Y14.5M-1994 4. FILENAME AND REVISION: MAC06AREV4 5. PIN ONE IDENTIFIER IS 2X LENGTH OF ANY OTHER LINE IN THE MARK CODE LAYOUT. Figure 8. 6-Lead, MicroPakTM, 1.0mm Wide Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild's worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor's online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/. Tape and Reel Specification Please visit Fairchild Semiconductor's online packaging area for the most recent tape and reel specifications: http://www.fairchildsemi.com/products/logic/pdf/micropak_tr.pdf. Package Designator L6X (c) 2002 Fairchild Semiconductor Corporation NC7SV08 * Rev. 1.0.4 Tape Section Cavity Number Cavity Status Cover Type Status Leader (Start End) 125 (Typical) Empty Sealed Carrier 5000 Filled Sealed Trailer (Hub End) 75 (Typical) Empty Sealed www.fairchildsemi.com 9 NC7SV08 -- TinyLogic(R) ULP-A 2-Input AND Gate Physical Dimensions 0.89 0.35 0.05 C 1.00 2X B A 5X 0.40 PIN 1 MIN 250uM 0.66 1.00 1X 0.45 6X 0.19 0.05 C TOP VIEW RECOMMENDED LAND PATTERN FOR SPACE CONSTRAINED PCB 2X 0.90 0.05 C 0.35 0.55MAX C 5X 0.52 SIDE VIEW 0.73 (0.08) 4X 1 DETAIL A 2 1X 0.57 0.09 0.19 6X 3 0.20 6X ALTERNATIVE LAND PATTERN FOR UNIVERSAL APPLICATION (0.05) 6X 5X 0.35 0.25 6 5 4 0.35 0.60 (0.08) 4X 0.10 .05 C C B A 0.40 0.30 BOTTOM VIEW NOTES: A. COMPLIES TO JEDEC MO-252 STANDARD B. DIMENSIONS ARE IN MILLIMETERS. C. DIMENSIONS AND TOLERANCES PER ASME Y14.5M, 1994 D. LANDPATTERN RECOMMENDATION IS BASED ON FSC DESIGN. E. DRAWING FILENAME AND REVISION: MGF06AREV3 Figure 9. 0.075X45 CHAMFER DETAIL A PIN 1 LEAD SCALE: 2X 6-Lead, MicroPak2, 1x1mm Body, .35mm Pitch Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild's worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor's online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/. Tape and Reel Specification Please visit Fairchild Semiconductor's online packaging area for the most recent tape and reel specifications: http://www.fairchildsemi.com/packaging/MicroPAK2_6L_tr.pdf. Package Designator FHX (c) 2002 Fairchild Semiconductor Corporation NC7SV08 * Rev. 1.0.4 Tape Section Cavity Number Cavity Status Cover Type Status Leader (Start End) 125 (Typical) Empty Sealed Carrier 5000 Filled Sealed Trailer (Hub End) 75 (Typical) Empty Sealed www.fairchildsemi.com 10 NC7SV08 -- TinyLogic(R) ULP-A 2-Input AND Gate (c) 2002 Fairchild Semiconductor Corporation NC7SV08 * Rev. 1.0.4 www.fairchildsemi.com 11