LM5010 LM5010 High Voltage 1A Step Down Switching Regulator Literature Number: SNVS307E LM5010 High Voltage 1A Step Down Switching Regulator General Description Features The LM5010 Step Down Switching Regulator features all the functions needed to implement a low cost, efficient, buck bias regulator capable of supplying in excess of 1A load current. This high voltage regulator contains an N-Channel Buck Switch, and is available in thermally enhanced LLP-10 and TSSOP-14EP packages. The hysteretic regulation scheme requires no loop compensation, results in fast load transient response, and simplifies circuit implementation. The operating frequency remains constant with line and load variations due to the inverse relationship between the input voltage and the on-time. The valley current limit detection is set at 1.25A. Additional features include: VCC under-voltage lockout, thermal shutdown, gate drive under-voltage lockout, and maximum duty cycle limiter. n n n n n n n n n n n n Input Voltage Range: 8V to 75V Valley Current Limit At 1.25A Switching Frequency Can Exceed 1 MHz Integrated N-Channel Buck Switch Integrated Startup Regulator No Loop Compensation Required Ultra-Fast Transient Response Operating Frequency Remains Constant With Load and Line Variations Maximum Duty Cycle Limited During Startup Adjustable Output Voltage Precision 2.5V Feedback Reference Thermal shutdown Typical Applications n n n n High Efficiency Point-Of-Load (POL) Regulator Non-Isolated Telecommunications Buck Regulator Secondary High Voltage Post Regulator Automotive Systems Package n LLP-10 (4 mm x 4 mm) n TSSOP-14EP n Both Packages Have Exposed Thermal Pad For Improved Heat Dissipation 20119943 Basic Stepdown Regulator (c) 2005 National Semiconductor Corporation DS201199 www.national.com LM5010 High Voltage 1A Step Down Switching Regulator February 2005 LM5010 Connection Diagrams 20119902 20119903 Ordering Information Order Number Package Type NSC Package Drawing Supplied As LM5010SD LLP-10 (4x4) SDC10A 1000 Units on Tape and Reel LM5010SDX LLP-10 (4x4) SDC10A 4500 Units on Tape and Reel LM5010MH TSSOP-14EP MXA14A 94 Units in Rail LM5010MHX TSSOP-14EP MXA14A 2500 Units on Tape and Reel www.national.com 2 LM5010 Pin Description PIN NUMBER LLP-10 TSSOP-14 NAME 1 2 SW Switching Node DESCRIPTION Internally connected to the buck switch source. Connect to the inductor, free-wheeling diode, and bootstrap capacitor. 2 3 BST Boost pin for bootstrap capacitor Connect a 0.022 F capacitor from SW to this pin. The capacitor is charged from VCC via an internal diode during each off-time. 3 4 ISEN Current sense The re-circulating current flows through the internal sense resistor, and out of this pin to the free-wheeling diode. Current limit is nominally set at 1.25A. 4 5 SGND Sense Ground Re-circulating current flows into this pin to the current sense resistor. 5 6 RTN Circuit Ground Ground for all internal circuitry other than the current limit detection. 6 9 FB Feedback input from the regulated output Internally connected to the regulation and over-voltage comparators. The regulation level is 2.5V. 7 10 SS Softstart An internal 11.5 A current source charges an external capacitor to 2.5V, providing the softstart function. 8 11 RON/SD On-time control and shutdown An external resistor from VIN to this pin sets the buck switch on-time. Grounding this pin shuts down the regulator. 9 12 VCC Output from the startup regulator Nominally regulates at 7.0V. An external voltage (7.5V-14V) can be applied to this pin to reduce internal dissipation. An internal diode connects VCC to VIN. 10 13 VIN Input supply voltage Nominal input range is 8.0V to 75V. 1,7,8,14 NC No connection. No internal connection. 3 APPLICATION INFORMATION www.national.com LM5010 Absolute Maximum Ratings (Note 1) VIN to SW If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. All Other Inputs to GND VIN to GND 76V BST to GND 90V SW to GND (Steady State) Current Out of ISEN 76V BST to SW 14V VCC to GND 14V SGND to RTN Human Body Model 2kV Storage Temperature Range -55C to +150C Lead Temperature (Soldering 4 sec) (Note 4) 260C Operating Ratings (Note 1) VIN -0.3V to +0.3V SS to RTN See Text -0.3 to 7V ESD Rating (Note 2) -1.5V BST to VCC 76V 8V to 75V Operating Junction Temperature -0.3V to 4V -40C to + 125C Electrical Charateristics Specifications with standard typeface are for TJ = 25C, and those with boldface type apply over full Operating Junction Temperature range. VIN = 48V, RON = 200k, unless otherwise stated (Note 5) and (Note 6). Symbol Parameter Conditions Min Typ Max Units 6.6 7 7.4 Volts VCC Regulator VCCReg UVLOVCC VCC regulated output VIN - VCC ICC = 0 mA, FS < 200 kHz 7.5V VIN 8.0V 1.3 V VCC output impedance (0 mA ICC 5 mA) VIN = 8.0V VIN = 48V 140 2.5 VCC current limit (Note 3) VCC = 0V 10 mA VCC under-voltage lockout threshold VCC increasing 5.8 V UVLOVCC hysteresis VCC decreasing 145 mV UVLOVCC filter delay 100 mV overdrive IIN operating current Non-switching, FB = 3V 650 850 A IIN shutdown current RON/SD = 0V 95 200 A 0.35 0.80 4.3 5.0 3 s Switch Characteristics Rds(on) UVLOGD Buck Switch Rds(on) ITEST = 200 mA Gate Drive UVLO VBST - VSW Increasing 3.0 V UVLOGD hysteresis 440 mV Pull-up voltage 2.5 V Internal current source 11.5 A Softstart Pin Current Limit ILIM Threshold Current out of ISEN 1 1.25 1.5 A Resistance from ISEN to SGND 130 m Response time 150 ns On Timer, RON/SD Pin tON - 1 On-time VIN = 10V, RON = 200 k 2.1 2.75 3.4 s tON - 2 On-time VIN = 75V, RON = 200 k 290 390 490 ns Shutdown threshold Voltage at RON/SD rising 0.35 0.65 1.1 Threshold hysteresis Voltage at RON/SD falling V 40 mV 265 ns Off Timer tOFF www.national.com Off-time 4 (Continued) Specifications with standard typeface are for TJ = 25C, and those with boldface type apply over full Operating Junction Temperature range. VIN = 48V, RON = 200k, unless otherwise stated (Note 5) and (Note 6). Symbol Parameter Conditions Min Typ Max 2.5 2.550 Units Regulation and Over-Voltage Comparators (FB Pin) VREF FB regulation threshold SS pin = steady state 2.445 FB over-voltage threshold V 2.9 V 1 nA Thermal shutdown temperature 175 C Thermal shutdown hysteresis 20 C 40 40 C/W FB bias current Thermal Shutdown TSD Thermal Resistance JA Junction to Ambient SDC Package MXA Package Note 1: Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which operation of the device is intended to be functional. For guaranteed specifications and test conditions, see the Electrical Characteristics. Note 2: The human body model is a 100pF capacitor discharged through a 1.5k resistor into each pin. Note 3: VCC provides bias for the internal gate drive and control circuits. Device thermal limitations limit external loading. Note 4: For detailed information on soldering plastic TSSOP and LLP packages refer to the Packaging Data Book available from National Semiconductor Corporation. Note 5: Typical specifications represent the most likely parametric norm at 25C operation. Note 6: All limits are guaranteed. All electrical characteristics having room temperature limits are tested during production with TA = 25C. All hot and cold limits are guaranteed by correlating the electrical characteristics to process and temperature variations and applying statistical process control. 5 www.national.com LM5010 Electrical Charateristics LM5010 Typical Application Circuit and Block Diagram (pin numbers are for the LLP-10 package) 20119944 FIGURE 1. www.national.com 6 LM5010 Typical Performance Characteristics 20119904 20119906 FIGURE 2. VCC vs VIN FIGURE 4. ICC vs Externally Applied VCC 20119905 20119907 FIGURE 3. VCC vs ICC FIGURE 5. On-Time vs VIN and RON 7 www.national.com LM5010 Typical Performance Characteristics (Continued) 20119910 FIGURE 7. IIN vs VIN 20119908 FIGURE 6. Voltage at RON/SD Pin www.national.com 8 LM5010 Typical Performance Characteristics (Continued) 20119911 FIGURE 8. Startup Sequence 48V telecom applications, as well as the new 42V automotive power bus. Implemented as a Point-of-Load regulator following a highly efficient intermediate bus converter can result in high overall system efficiency. Features include: Thermal shutdown, VCC under-voltage lockout, gate drive under-voltage lockout, and maximum duty cycle limit. Functional Description The LM5010 Step Down Switching Regulator features all the functions needed to implement a low cost, efficient buck bias power converter capable of supplying in excess of 1A to the load. This high voltage regulator contains an N-Channel buck switch, is easy to implement, and is available in the thermally enhanced LLP-10 and TSSOP-14EP packages. The regulator's operation is based on a hysteretic control scheme, and uses an on-time which varies inversely with VIN. This feature results in the operating frequency remaining relatively constant with load and input voltage variations. The switching frequency can range from 100 kHz to > 1.0 MHz. The hysteretic control requires no loop compensation resulting in very fast load transient response. The valley current limit detection circuit, internally set at 1.25A, holds the buck switch off until the high current level subsides. Figure 1 shows the functional block diagram. The LM5010 can be applied in numerous applications to efficiently regulate down higher voltages. This regulator is well suited for Hysteretic Control Circuit Overview The LM5010 buck DC-DC regulator employs a control scheme based on a comparator and a one-shot on-timer, with the output voltage feedback (FB) compared to an internal reference (2.5V). If the FB voltage is below the reference the buck switch is turned on for a time period determined by the input voltage and a programming resistor (RON). Following the on-time the switch remains off for 265 ns, or until the FB voltage falls below the reference, whichever is longer. The buck switch then turns on for another on-time period. 9 www.national.com LM5010 Hysteretic Control Circuit Overview (Continued) Typically when the load current increases suddenly, the offtimes are temporarily at the minimum of 265 ns. Once regulation is established, the off-time resumes its normal value. The output voltage is set by two external resistors (R1, R2). The regulated output voltage is calculated as follows: (1) VOUT = 2.5V x (R1 + R2) / R2 (3) At low load current, the circuit operates in discontinuous conduction mode, during which the inductor current ramps up from zero to a peak during the on-time, then ramps back to zero before the end of the off-time. The next on-time period starts when the voltage at FB falls below the reference - until then the inductor current remains zero, and the load current is supplied by the output capacitor (C2). In this mode the operating frequency is lower than in continuous conduction mode, and varies with load current. Conversion efficiency is maintained at light loads since the switching losses reduce with the reduction in load and frequency. The approximate discontinuous operating frequency can be calculated as follows: Output voltage regulation is based on ripple voltage at the feedback input, requiring a minimum amount of ESR for the output capacitor C2. The LM5010 requires a minimum of 25 mV of ripple voltage at the FB pin. In cases where the capacitor's ESR is insufficient additional series resistance may be required (R3 in Figure 1 ). When in regulation, the LM5010 operates in continuous conduction mode at heavy load currents and discontinuous conduction mode at light load currents. In continuous conduction mode current always flows through the inductor, never reaching zero during the off-time. In this mode the operating frequency remains relatively constant with load and line variations. The minimum load current for continuous conduction mode is one-half the inductor's ripple current amplitude. The approximate operating frequency is calculated as follows: (4) where RL = the load resistance. For applications where lower output voltage ripple is required the output can be taken directly from a low ESR output capacitor as shown in Figure 9. However, R3 slightly degrades the load regulation. (2) The buck switch duty cycle is approximately equal to: 20119915 FIGURE 9. Low Ripple Output Configuration The minimum input operating voltage is determined by the regulator's dropout voltage, the VCC UVLO falling threshold ()5.65V), and the frequency. When VCC falls below the falling threshold the VCC UVLO activates to shut off the buck switch and ground the softstart pin. If VCC is externally loaded, the minimum input voltage increases since the output impedance at VCC is )140 at low VIN. See Figures 2 and 3. In applications involving a high value for VIN where power dissipation in the startup regulator is a concern, an auxiliary voltage can be diode connected to the VCC pin (Figure 10). Setting the auxiliary voltage to between 7.5V and 14V shuts off the internal regulator, reducing internal power dissipation. The current required into the VCC pin is shown in Figure 4. Internally a diode connects VCC to VIN. Start-up Regulator (VCC) The startup regulator is integral to the LM5010. The input pin (VIN) can be connected directly to line voltages up to 75V. The VCC output is regulated at 7.0V, 6%, and is current limited to 10 mA. Upon power up the regulator sources current into the external capacitor at VCC (C3). With a 0.1 F capacitor at VCC, approximately 58 s are required for the VCC voltage to reach the under-voltage lockout threshold (UVLO) of 5.8V (t1 in Figure 8), at which time the buck switch is enabled, and the softstart pin is released to allow the softstart capacitor (C6) to charge up. VOUT then increases to its regulated value as the softstart voltage increases (t2 in Figure 8). www.national.com 10 LM5010 Start-up Regulator (VCC) (Continued) 20119916 FIGURE 10. Self Biased Configuration Regulation Comparator The feedback voltage at FB is compared to the voltage at the Softstart pin (2.5V, 2%). In normal operation (the output voltage is regulated) an on-time period is initiated when the voltage at FB falls below 2.5V. The buck switch stays on for the on-time causing the FB voltage to rise above 2.5V. After the on-time period the buck switch stays off until the FB voltage falls below 2.5V. Bias current at the FB pin is less than 5 nA over temperature. (5) The inverse relationship of tON vs. VIN results in a nearly constant frequency as VIN is varied. If the application requires a high frequency the minimum value for tON, and consequently RON, is limited by the off-time (265 ns, 15%) which limits the maximum duty cycle at minimum VIN. The tolerance for Equation 5 is 25%. Frequencies in excess of 1 MHz are possible with the LM5010. Over-Voltage Comparator The feedback voltage at FB is compared to an internal 2.9V reference. If the voltage at FB rises above 2.9V the on-time is immediately terminated. This condition can occur if the input voltage, or the output load, change suddenly. The buck switch will not turn on again until the voltage at FB falls below 2.5V. Shutdown The LM5010 can be remotely shut down by taking the RON/SD pin below 0.65V. See Figure 11. In this mode the softstart pin is internally grounded, the on-timer is disabled, and the input current at VIN is reduced (Figure 7). Releasing the RON/SD pin allows normal operation to resume. When the switch is open, the nominal voltage at RON/SD is shown in Figure 6. ON-Time Control The on-time of the internal switch (see Figure 5) is determined by the RON resistor and the input voltage (VIN), calculated from the following: 20119918 FIGURE 11. Shutdown Implementation 11 www.national.com LM5010 current ratchets up until the lower peak attempts to exceed the threshold. During the Current Limited portion of Figure 12, the current ramps down to the threshold during each off-time, initiating the next on-time (assuming the voltage at FB is < 2.5V). During each on-time the current ramps up an amount equal to: Current Limit Current limit detection occurs during the off-time by monitoring the recirculating current through the free-wheeling diode (D1). The detection threshold is 1.25A, 0.25A. Referring to Figure 1, when the buck switch is off the inductor current flows through the load, into SGND, through the sense resistor, out of ISEN and through D1. If that current exceeds the threshold the current limit comparator output switches to delay the start of the next on-time period. The next on-time starts when the current out of ISEN is below the threshold and the voltage at FB is below 2.5V. If the overload condition persists causing the inductor current to exceed the threshold during each on-time, that is detected at the beginning of each off-time. The operating frequency is lower due to longer-than-normal off-times. (6) During this time the LM5010 is in a constant current mode, with an average load current (IOCL) equal to the threshold + I/2. The "valley current limit" technique allows the load current to exceed the current limit threshold as long as the lower peak of the inductor current is less than the threshold. Figure 12 illustrates the inductor current waveform. During normal operation the load current is IO, the average of the ripple waveform. When the load resistance decreases the 20119920 FIGURE 12. Inductor Current - Current Limit Operation The current limit threshold can be increased by connecting an external resistor (RCL) between SGND and ISEN. The external resistor typically is less than 1, and its calculation is explained in the Applications Information section. The peak current out of SW and ISEN must not exceed 3.5A. The average current out of SW must be less than 3A, and the average current out of ISEN must be less than 2A. Softstart The softstart feature allows the converter to gradually reach a steady state operating point, thereby reducing startup stresses and current surges. Upon turn-on, after VCC reaches the under-voltage threshold (t1 in Figure 8), an internal 11.5 A current source charges the external capacitor at the Softstart pin to 2.5V (t2 in Figure 8). The ramping voltage at SS (and at the non-inverting input of the regulation comparator) ramps up the output voltage in a controlled manner. This feature keeps the load current from going to current limit during startup, thereby reducing inrush currents. An internal switch grounds the Softstart pin if VCC is below the under-voltage lockout threshold, if a thermal shutdown occurs, or if the circuit is shutdown using the RON/SD pin. N - Channel Buck Switch and Driver The LM5010 integrates an N-Channel buck switch and associated floating high voltage gate driver. The peak current through the buck switch must not be allowed to exceed 3.5A, and the average current must be less than 3A. The gate driver circuit is powered by the external bootstrap capacitor between BST and SW (C4). During each off-time, the SW pin is at approximately -1V, and C4 is re-charged from VCC through the internal high voltage diode. The minimum offtime of 265 ns ensures a minimum time each cycle to recharge the bootstrap capacitor. A 0.022 F ceramic capacitor is recommended for C4. www.national.com Thermal Shutdown The LM5010 should be operated so the junction temperature does not exceed 125C. If the junction temperature increases above that, an internal Thermal Shutdown circuit activates (typically) at 175C, taking the controller to a low power reset state by disabling the buck switch and the on-timer, and grounding the Softstart pin. This feature helps prevent catastrophic failures from accidental device over12 RON, FS: RON sets the on-time, and can be chosen using Equation 2 to set a nominal frequency, or from Equation 5 if the on-time at a particular VIN is important. A higher frequency generally means a smaller inductor and capacitors (value, size and cost), but higher switching losses. A lower frequency means a higher efficiency, but with larger components. If PC board space is tight, a higher frequency is better. The resulting on-time and frequency have a 25% tolerance. Re-arranging Equation 2 , (Continued) heating. When the junction temperature reduces below 155C (typical hysteresis = 20C), the Softstart pin is released and normal operation resumes. Applications Information EXTERNAL COMPONENTS The procedure for calculating the external components is illustrated with a design example. The circuit in Figure 1 is to be configured for the following specifications: * VOUT = 10V * VIN = 15V to 75V The next larger standard value (137 k) is chosen for RON, yielding a nominal frequency of 618 kHz. * FS = 625 kHz * Minimum load current = 150 mA * Maximum load current = 1.0A * Softstart time = 5 ms. R1 and R2:The ratio of these resistors is calculated from: R1/R2 = (VOUT/2.5V) - 1 (7) R1/R2 calculates to 3.0. The resistors should be chosen from standard value resistors in the range of 1.0 k - 10 k. Values of 3.0 k for R1, and 1.0 k for R2 will be used. L1: The inductor value is determined based on the load current, ripple current, and the minimum and maximum input voltage (VIN(min), VIN(max)). Refer to Figure 13 . 20119922 FIGURE 13. Inductor Current To keep the circuit in continuous conduction mode, the maximum allowed ripple current is twice the minimum load current, or 300 mAp-p. Using this value of ripple current, the inductor (L1) is calculated using the following: (9) (8) where FS(min) is the minimum frequency (FS - 25%). IPK+ = 1.0A + 0.234A / 2 = 1.117A RCL: Since it is obvious that the lower peak of the inductor current waveform does not exceed 1.0A at maximum load current (see Figure 13), it is not necessary to increase the current limit threshold. Therefore RCL is not needed for this exercise. For applications where the lower peak exceeds 1.0A, see the section below on increasing the current limit threshold. C2 and R3: Since the LM5010 requires a minimum of 25 mVp-p of ripple at the FB pin for proper operation, the required ripple at VOUT1 is increased by R1 and R2. This necessary ripple is created by the inductor ripple current acting on C2's ESR + R3. First, the minimum ripple current is determined. This provides a minimum value for L1 - the next higher standard value (100 H) will be used. L1 must be rated for the peak current (IPK+) to prevent saturation. The peak current occurs at maximum load current with maximum ripple. The maximum ripple is calculated by re-arranging Equation 8 using VIN(max), FS(min), and the minimum inductor value, based on the manufacturer's tolerance. Assume, for this exercise, the inductor's tolerance is 20%. 13 www.national.com LM5010 Thermal Shutdown LM5010 Applications Information peak of the output current waveform, ramps up to the peak value, then drops to zero at turn-off. The average current into VIN during this on-time is the load current. For a worst case calculation, C1 must supply this average load current during the maximum on-time. The maximum on-time is calculated using Equation 5, with a 25% tolerance added: (Continued) (10) C1 is calculated from: The minimum ESR for C2 is then equal to: where IO is the load current, and V is the allowable ripple voltage at VIN (1V for this example). Quality ceramic capacitors with a low ESR should be used for C1. To allow for capacitor tolerances and voltage effects, a 2.2 F capacitor will be used C3: The capacitor at the VCC pin provides not only noise filtering and stability, but also prevents false triggering of the VCC UVLO at the buck switch on/off transitions. For this reason, C3 should be no smaller than 0.1 F, and should be a good quality, low ESR, ceramic capacitor. This capacitor also determines the initial startup delay (t1 in Figure 8). If the capacitor used for C2 does not have sufficient ESR, R3 is added in series as shown in Figure 1. C2 should generally be no smaller than 3.3 F, although that is dependent on the frequency and the allowable ripple amplitude at VOUT1. Experimentation is usually necessary to determine the minimum value for C2, as the nature of the load may require a larger value. A load which creates significant transients requires a larger value for C2 than a non-varying load. D1: The important parameters are reverse recovery time and forward voltage drop. The reverse recovery time determines how long the current surge lasts each time the buck switch is turned on. The forward voltage drop is significant in the event the output is short-circuited as it is mainly this diode's voltage (plus the voltage across the current limit sense resistor) which forces the inductor current to decrease during the off-time. For this reason, a higher voltage is better, although that affects efficiency. A reverse recovery time of )30 ns, and a forward voltage drop of )0.75V are preferred. The reverse leakage specification is important as that can significantly affect efficiency. Other types of diodes may have a lower forward voltage drop, but may have longer recovery times, or greater reverse leakage. D1 should be rated for the maximum VIN, and for the peak current when in current limit (IPK in Figure 11) which is equal to: IPK = 1.5A + IOR(max) = 1.734A where 1.5A is the maximum guaranteed current limit threshold, and the maximum ripple current was previously calculated as 234 mAp-p. Note that this calculation is valid only when RCL is not required. C1: Assuming the voltage supply feeding VIN has a source impedance greater than zero, this capacitor limits the ripple voltage at VIN while supplying most of the switch current during the on-time. At maximum load current, when the buck switch turns on, the current into VIN increases to the lower www.national.com C4: The recommended value for C4 is 0.022 F. A high quality ceramic capacitor with low ESR is recommended as C4 supplies the surge current to charge the buck switch gate at turn-on. A low ESR also ensures a complete recharge during each off-time. C5: This capacitor suppresses transients and ringing due to long lead inductance at VIN. A low ESR, 0.1 F ceramic chip capacitor is recommended, located physically close to the LM5010. C6: The capacitor at the SS pin determines the softstart time, i.e. the time for the reference voltage at the regulation comparator, and the output voltage, to reach their final value. The time is determined from the following: For a 5 ms softstart time, C6 calculates to 0.022 F. FINAL CIRCUIT The final circuit is shown in Figure 14, and its performance is shown in Figures 15 - 18. 14 LM5010 Applications Information (Continued) 20119933 FIGURE 14. LM5010 Example Circuit Item Description Part No. Package Value C1 Ceramic Capacitor TDK C4532X7R2A225M 1812 2.2 F, 100V C2 Ceramic Capacitor TDK C4532X7R1E156M 1812 15 F, 25V C3 Ceramic Capacitor Kemet C0805C104K4RAC 0805 0.1 F, 16V C4, C6 Ceramic Capacitor Kemet C0805C223K4RAC 0805 0.022 F, 16V C5 Ceramic Capacitor TDK C2012X7R2A104M 0805 0.1 F, 100V D1 Ultra fast diode Central Semi CMR2U-01 SMB 100V, 2A L1 Inductor TDK SLF10145 10.1 x 10.1 100 H R1 Resistor Vishay CRCW08053001F 0805 3.0 k R2 Resistor Vishay CRCW08051001F 0805 1.0 k R3 Resistor Vishay CRCW08052R80F 0805 2.8 RON Resistor Vishay CRCW08051373F 0805 137 k U1 Switching regulator National Semi LM5010 15 www.national.com LM5010 Applications Information (Continued) 20119936 FIGURE 17. Output Voltage Ripple vs VIN Circuit of Figure 14 20119934 FIGURE 15. Efficiency vs VIN Circuit of Figure 14 20119937 FIGURE 18. Frequency vs VIN Circuit of Figure 14 20119935 FIGURE 16. Efficiency vs Load Current and VIN Circuit of Figure 14 INCREASING THE CURRENT LIMIT THRESHOLD The current limit threshold is nominally 1.25A, with a minimum guaranteed value of 1.0A. If, at maximum load current, the lower peak of the inductor current (IPK- in Figure 13) exceeds 1.0A, resistor RCL must be added between SGND and ISEN to increase the current limit threshold to equal or exceed that lower peak current. This resistor diverts some of the recirculating current from the internal sense resistor so that a higher current level is needed to switch the internal current limit comparator. IPK- is calculated from: (11) where IO(max) is the maximum load current, and IOR(min) is the minimum ripple current calculated using Equation 10. RCL is calculated from: www.national.com 16 LM5010 Applications Information (Continued) The inductor L1 and diode D1 must be rated for this current. (12) where 0.11 is the minimum value of the internal resistance from SGND to ISEN. The next smaller standard value resistor should be used for RCL. With the addition of RCL it is necessary to check the average and peak current values to ensure they do not exceed the LM5010 limits. At maximum load current the average current through the internal sense resistor is: PC BOARD LAYOUT The LM5010 regulation, over-voltage, and current limit comparators are very fast, and will respond to short duration noise pulses. Layout considerations are therefore critical for optimum performance. The layout must be as neat and compact as possible, and all the components must be as close as possible to their associated pins. The current loop formed by D1, L1, C2, and the SGND and ISEN pins should be as small as possible. The ground connection from C2 to C1 should be as short and direct as possible. If it is expected that the internal dissipation of the LM5010 will produce high junction temperatures during normal operation, good use of the PC board's ground plane can help considerably to dissipate heat. The exposed pad on the IC package bottom can be soldered to a ground plane, and that plane should both extend from beneath the IC, and be connected to exposed ground plane on the board's other side using as many vias as possible. The exposed pad is internally connected to the IC substrate. The use of wide PC board traces at the pins, where possible, can help conduct heat away from the IC. The four No Connect pins on the TSSOP package are not electrically connected to any part of the IC, and may be connected to ground plane to help dissipate heat from the package. Judicious positioning of the PC board within the end product, along with the use of any available air flow (forced or natural convection) can help reduce the junction temperature. (13) If IAVE is less than 2.0A no changes are necessary. If it exceeds 2.0A, RCL must be reduced. The upper peak of the inductor current (IPK+), at maximum load current, is calculated using the following: (14) where IOR(max) is calculated using Equation 9. If IPK+ exceeds 3.5A , the inductor value must be increased to reduce the ripple amplitude. This will necessitate recalculation of IOR(min), IPK-, and RCL. When the circuit is in current limit, the upper peak current out of the SW pin is 17 www.national.com LM5010 Physical Dimensions inches (millimeters) unless otherwise noted 14-Lead TSSOP Package NS Package Number MXA14A 10-Lead LLP Package NS Package Number SDC10A www.national.com 18 LM5010 High Voltage 1A Step Down Switching Regulator Notes National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ``Banned Substances'' as defined in CSP-9-111S2. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated