|VDD ±| − Supply Voltage − V
10
8
6
4
12
14
16
MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE
vs
SUPPLY VOLTAGE
TA= 25°C
IO= ± 50 µA
IO= ± 500 µA
V(OPP) −Maximum Peak-to-Peak Output Voltage −V
VO(PP)
46 8 10 12 14 16
TLC2272-Q1 , TLC2272A-Q1
TLC2274-Q1, TLC2274A-Q1
www.ti.com
SGLS007E –FEBRUARY 2003–REVISED JANUARY 2012
ADVANCED LinCMOS™RAIL-TO-RAIL OPERATIONAL AMPLIFIERS
Check for Samples: TLC2272-Q1 ,TLC2272A-Q1 ,TLC2274-Q1,TLC2274A-Q1
1FEATURES
2•Qualified for Automotive Applications •High-Gain Bandwidth . . . 2.2 MHz Typ
•Output Swing Includes Both Supply Rails •High Slew Rate . . . 3.6 V/μs Typ
•Low Noise . . . 9 nV/√Hz Typ at f = 1 kHz •Low Input Offset Voltage
950 μV Max at TA= 25°C
•Low Input Bias Current . . . 1 pA Typ •Macromodel Included
•Fully Specified for Both Single-Supply and
Split-Supply Operation •Performance Upgrades for the TS272, TS274,
TLC272, and TLC274
•Common-Mode Input Voltage Range Includes
Negative Rail
DESCRIPTION
The TLC2272 and TLC2274 are dual and quadruple
operational amplifiers from Texas Instruments. Both
devices exhibit rail-to-rail output performance for
increased dynamic range in single- or split-supply
applications. The TLC227x family offers 2 MHz of
bandwidth and 3 V/μs of slew rate for higher speed
applications. These devices offer comparable ac
performance while having better noise, input offset
voltage, and power dissipation than existing CMOS
operational amplifiers. The TLC227x has a noise
voltage of 9 nV/√Hz, two times lower than competitive
solutions.
The TLC227x, exhibiting high input impedance and
low noise, is excellent for small-signal conditioning for
high-impedance sources, such as piezoelectric
transducers. Because of the micropower dissipation
levels, these devices work well in hand-held
monitoring and remote-sensing applications. In
addition, the rail-to-rail output feature, with single- or
split-supplies, makes this family a great choice when
interfacing with analog-to-digital converters (ADCs).
For precision applications, the TLC227xA family is The TLC2272/4 also makes great upgrades to the
available with a maximum input offset voltage of 950 TLC272/4 or TS272/4 in standard designs. They offer
μV. This family is fully characterized at 5 V and ±5 V. increased output dynamic range, lower noise voltage,
and lower input offset voltage. This enhanced feature
set allows them to be used in a wider range of
applications. For applications that require higher
output drive and wider input voltage range, see the
TLV2432 and TLV2442 devices.
1Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2ADVANCED LinCMOS is a trademark of Texas Instruments.
PRODUCTION DATA information is current as of publication date. Copyright ©2003–2012, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Q3 Q6 Q9 Q12 Q14 Q16
Q2 Q5 Q7 Q8 Q10 Q11
D1
Q17Q15Q13
Q4Q1
R5
C1
VDD +
IN +
IN −
R3 R4 R1 R2
OUT
VDD−
TLC2272-Q1 , TLC2272A-Q1
TLC2274-Q1, TLC2274A-Q1
SGLS007E –FEBRUARY 2003–REVISED JANUARY 2012
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
AVAILABLE OPTIONS
PACKAGED DEVICES(1)(2)
TAVIOmax At 25°CSMALL OUTLINE (D) TSSOP (PW)
950 μV TLC2272AQDRQ1 TLC2272AQPWRQ1
-40°C to 125°C2.5 mV TLC2272QDRQ1 TLC2272QPWRQ1
950 μV TLC2274AQDRQ1 TLC2274AQPWRQ1
-40°C to 125°C2.5 mV TLC2274QDRQ1 TLC2274QPWRQ1
(1) For the most current package and ordering information, see the Package Option Addendum at the end
of this document, or see the TI web site at www.ti.com.
(2) Package drawings, thermal data, and symbolization are available at www.ti.com/packaging.
Equivalent Schematic (Each Amplifier)
2Submit Documentation Feedback Copyright ©2003–2012, Texas Instruments Incorporated
Product Folder Link(s): TLC2272-Q1 TLC2272A-Q1 TLC2274-Q1 TLC2274A-Q1
TLC2272-Q1 , TLC2272A-Q1
TLC2274-Q1, TLC2274A-Q1
www.ti.com
SGLS007E –FEBRUARY 2003–REVISED JANUARY 2012
Actual Device Component Count(1)
COMPONENT TLC2272 TLC2274
Transistors 38 76
Resistors 26 52
Diodes 9 18
Capacitors 3 6
(1) Includes both amplifiers and all ESD, bias, and trim circuitry
ABSOLUTE MAXIMUM RATINGS(1)
over operating free-air temperature range (unless otherwise noted) VALUE UNIT
VDD+ Supply voltage(2) 8 V
VDD−Supply voltage(2) −8 V
VID Differential input voltage(3) ±16 V
VIInput voltage range(2) Any input VDD−−0.3 to VDD+ V
IIInput current Any input ±5 mA
IOOutput current ±50 mA
Total current into VDD+ ±50 mA
Total current out of VDD−±50 mA
Duration of short-circuit current at (or below) 25°C(4) unlimited
Continuous total dissipation See Dissipation Ratings
TAOperating free-air temperature range -40°C to 125°C°C
Tstg Storage temperature range −65 to 150 °C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds D or PW package 260 °C
(1) Stresses beyond those listed under “absolute maximum ratings”may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating
conditions”is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltage values, except differential voltages, are with respect to the midpoint between VDD+ and VDD −.
(3) Differential voltages are at IN+ with respect to IN−. Excessive current will flow if input is brought below VDD−−0.3 V.
(4) The output may be shorted to either supply. Temperature and/or supply voltages must be limited to ensure that the maximum dissipation
rating is not exceeded.
DISSIPATION RATINGS DERATING
TA≤25°C TA= 70°C TA= 85°C TA= 125°C
PACKAGE FACTOR
POWER RATING POWER RATING POWER RATING POWER RATING
ABOVE TA= 25°C
D-8 725 mW 5.8 mW/°C 464 mW 337 mW 145 mW
D-14 950 mW 7.6 mW/°C 608 mW 494 mW 190 mW
D-14 525 mW 4.2 mW/°C 336 mW 273 mW 105 mW
D-14 700 mW 5.6 mW/°C 448 mW 364 mW -
RECOMMENDED OPERATING CONDITIONS
over operating free-air temperature range (unless otherwise noted) MIN MAX UNIT
VDD±Supply voltage ±2.2 ±8 V
VIInput voltage VDD−VDD+ −1.5 V
VIC Common-mode input voltage VDD−VDD+ −1.5 V
TAOperating free-air temperature −40 125 °C
Copyright ©2003–2012, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Link(s): TLC2272-Q1 TLC2272A-Q1 TLC2274-Q1 TLC2274A-Q1
TLC2272-Q1 , TLC2272A-Q1
TLC2274-Q1, TLC2274A-Q1
SGLS007E –FEBRUARY 2003–REVISED JANUARY 2012
www.ti.com
TLC2272Q ELECTRICAL CHARACTERISTICS
at specified free-air temperature, VDD = 5 V (unless otherwise noted) TLC2272Q TLC2272AQ
PARAMETER TEST CONDITIONS TA(1) UNIT
MIN TYP MAX MIN TYP MAX
25°C 300 2500 300 950
VIO Input offset voltage μV
Full range 3000 1600
Temperature coefficient
αVIO 25°C to 125°C 2 2 μV/°C
of input offset voltage
Input offset voltage μV/m
VIC = 0 V, VDD±=±2.5 V, 25°C 0.002 0.002
long-term drift(2) o
VO= 0 V, RS= 50 Ω
25°C 0.5 60 0.5 60
IIO Input offset current pA
Full range 800 800
25°C 1 1 60
IIB Input bias current pA
Full range 800
−0.3 to −0.3 to
25°C 0 to 4 0 to 4
4.2 4.2
Common-mode input
VICR RS= 50 Ω|VIO|≤5 mV V
voltage range 0 to
Full range 0 to 3.5 3.5
IOH =−20 μA 25°C 4.99 4.99
25°C 4.85 4.93 4.85 4.93
IOH =−200 μA
VOH High-level output voltage Full range 4.85 4.85 V
25°C 4.25 4.65 4.25 4.65
IOH =−1 mA Full range 4.25 4.25
VIC = 2.5 V, IOL = 50 μA 25°C 0.01 0.01
25°C 0.09 0.15 0.09 0.15
VIC = 2.5 V, IOL = 500 μA
VOL Low-level output voltage Full range 0.15 0.15 V
25°C 0.9 1.5 0.9 1.5
VIC = 2.5 V, IOL = 5 mA Full range 1.5 1.5
25°C 10 35 10 35
RL= 10 kΩ(3)
Large-signal differential VIC = 2.5 V,
AVD Full range 10 10 V/mV
voltage amplification VO= 1 V to 4 V, RL= 1 MΩ(3) 25°C 175 175
Differential input
rid 25°CΩ
1012 1012
resistance
Common-mode input
ri25°CΩ
1012 1012
resistance
Common-mode input f = 10 kHz, P package
ci25°C 8 8 pF
capacitance
Closed-loop output f = 1 MHz, AV= 10
zo25°C 140 140 Ω
impedance
VIC = 0 V to 2.7 RS= 50 Ω25°C 70 75 70 75
CMR Common-mode rejection V, dB
R ratio Full range 70 70
VO= 2.5 V,
VDD = 4.4 V to 16 V, 25°C 80 95 80 95
Supply voltage rejection
kSVR dB
ratio (ΔVDD/ΔVIO)VIC = VDD/2, No load Full range 80 80
25°C 2.2 3 2.2 3
IDD Supply current VO= 2.5 V, No load mA
Full range 3 3
(1) Full range is −40°C to 125°C for Q level part.
(2) Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA= 150°C extrapolated to
TA= 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
(3) Referenced to 2.5 V
4Submit Documentation Feedback Copyright ©2003–2012, Texas Instruments Incorporated
Product Folder Link(s): TLC2272-Q1 TLC2272A-Q1 TLC2274-Q1 TLC2274A-Q1
TLC2272-Q1 , TLC2272A-Q1
TLC2274-Q1, TLC2274A-Q1
www.ti.com
SGLS007E –FEBRUARY 2003–REVISED JANUARY 2012
TLC2272Q OPERATING CHARACTERISTICS
at specified free-air temperature, VDD = 5 V (unless otherwise noted) TLC2272Q TLC2272AQ
PARAMETER TEST CONDITIONS TA(1) UNIT
MIN TYP MAX MIN TYP MAX
VO=1.25 V to CL= 100 pF(2) 25°C 2.3 3.6 2.3 3.6
SR Slew rate at unity gain 2.75 V, V/μs
Full range 1.7 1.7
RL= 10 kΩ(2)
f = 10 Hz 25°C 50 50
Equivalent input noise nV/√
Vnvoltage Hz
f = 1 kHz 25°C 9 9
f = 0.1 to 1 Hz 25°C 1 1
Peak-to-peak equivalent
VN(pp) μV
input noise voltage f = 0.1 to 10 Hz 25°C 1.4 1.4
Equivalent input noise fA/√H
In25°C 0.6 0.6
current z
VO= 0.5V to AV= 1 0.0013 0.0013
2.5V, % %
THD Total harmonic distortion RL= 10 kΩ,25°C
+ N plus noise AV= 10 0.004% 0.004%
f = 20 kHz (2)
AV= 100 0.03% 0.03%
Gain-bandwidth product f = 10 kHz, RL= 10 kΩ(2) 25°C 2.18 2.18 MHz
CL= 100 pF(2)
BOM Maximum output-swing VO(PP) = 2V, AV= 1, 25°C 1 1 MHz
bandwidth RL= 10 kΩ(2) CL= 100 pF(2)
AV= -1, To 0.1% 1.5 1.5
Step = 0.5V to
tsSettling time 2.5V, 25°Cμs
To 0.01% 2.6 2.6
RL= 10 kΩ(3)
CL= 100 pF(3)
φmPhase margin at unity 25°C 50°50°
gain RL= 10 kΩ(3), CL= 100 pF(3)
Gain margin 25°C 10 10 dB
(1) Full range is −40°C to 125°C for Q level part.
(2) Referenced to 2.5 V
(3) Referenced to 2.5 V
Copyright ©2003–2012, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Link(s): TLC2272-Q1 TLC2272A-Q1 TLC2274-Q1 TLC2274A-Q1
TLC2272-Q1 , TLC2272A-Q1
TLC2274-Q1, TLC2274A-Q1
SGLS007E –FEBRUARY 2003–REVISED JANUARY 2012
www.ti.com
TLC2272Q ELECTRICAL CHARACTERISTICS
at specified free-air temperature, VDD±=±5 V (unless otherwise noted) TLC2272Q TLC2272AQ
PARAMETER TEST CONDITIONS TA(1) UNIT
MIN TYP MAX MIN TYP MAX
25°C 300 2500 300 950
VIO Input offset voltage μV
Full range 3000 1500
Temperature
αVIO coefficient of input 25°C to 125°C 2 2 μV/°C
offset voltage VIC = 0 V,
Input offset voltage μV/m
VO= 0 V 25°C 0.002 0.002
RS= 50 Ω
long-term drift(2) o
25°C 0.5 60 0.5 60
IIO Input offset current pA
Full range 800 800
25°C 1 60 1 60
IIB Input bias current pA
Full range 800 800
−5.3 to −5.3 to
25°C−5 to 4 −5 to 4
4.2 4.2
Common-mode input |VIO|≤5
VICR RS= 50 ΩV
voltage range mV −5 to
Full range −5 to 3.5
3.5
IO=−20 μA 25°C 4.99 4.99
25°C 4.85 4.93 4.85 4.93
IO=−200 μA
Maximum positive
VOM+ Full range 4.85 4.85 V
peak output voltage 25°C 4.25 4.65 4.25 4.65
IO=−1 mA Full range 4.25 4.25
VIC = 0 V, IO= 50 μA 25°C−4.99 −4.99
25°C−4.85 −4.91 −4.85 −4.91
IO= 500
VIC = 0 V,
Maximum negative μA
VOM- Full range −4.85 −4.85 V
peak output voltage 25°C−3.5 −4.1 −3.5 −4.1
VIC = 0 V, IO= 5 mA Full range −3.5 −3.5
25°C 20 50 20 50
Large-signal RL= 10 kΩ
AVD differential voltage VO=±4 V, Full range 20 20 V/mV
amplification RL= 1 MΩ25°C 300 300
Differential input
rid 25°CΩ
1012 1012
resistance
Common-mode input
ri25°CΩ
1012 1012
resistance
Common-mode input f = 10 kHz, N package
ci25°C 8 8 pF
capacitance
Closed-loop output f = 1 MHz, AV = 10
zo25°C 130 130 Ω
impedance
VIC = -5 V to RS= 50 Ω25°C 75 80 75 80
CMR Common-mode 2.7 V, dB
R rejection ratio Full range 75 75
VO= 0 V,
Supply voltage VDD =±2.2 V to ±8 V, 25°C 80 95 80 95
kSVR rejection ratio dB
VIC = 0V, No load Full range 80 80
(ΔVDD/ΔVIO)
25°C 2.4 3 2.4 3
IDD Supply current VO= 0 V, No load mA
Full range 3 3
(1) Full range is −40°C to 125°C for Q level part.
(2) Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA= 150°C extrapolated to
TA= 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
6Submit Documentation Feedback Copyright ©2003–2012, Texas Instruments Incorporated
Product Folder Link(s): TLC2272-Q1 TLC2272A-Q1 TLC2274-Q1 TLC2274A-Q1
TLC2272-Q1 , TLC2272A-Q1
TLC2274-Q1, TLC2274A-Q1
www.ti.com
SGLS007E –FEBRUARY 2003–REVISED JANUARY 2012
TLC2272Q OPERATING CHARACTERISTICS
at specified free-air temperature, VDD±=±5 V (unless otherwise noted) TLC2272Q TLC2272AQ
PARAMETER TEST CONDITIONS TA(1) UNIT
MIN TYP MAX MIN TYP MAX
VO=±2.3 V, CL= 100 25°C 2.3 3.6 2.3 3.6
Slew rate at unity
SR V/μs
RL= 10 kΩpF
gain Full range 1.7 1.7
f = 10 Hz 25°C 50 50
Equivalent input nV/√H
Vnnoise voltage z
f = 1 kHz 25°C 9 9
Peak-to-peak f = 0.1 to 1 Hz 25°C 1 1
VN(pp) equivalent input μV
f = 0.1 to 10 Hz 25°C 1.4 1.4
noise voltage
Equivalent input fA/√H
In25°C 0.6 0.6
noise current z
AV= 1 0.0011% 0.0011%
VO=±2.3 V,
THD Total harmonic f = 20 kHz, AV= 10 25°C 0.004% 0.004%
+ N distortion plus noise RL= 10 kΩAV= 100 0.03% 0.03%
Gain-bandwidth f = 10 kHz, RL= 10 kΩ25°C 2.25 2.25 MHz
product CL= 100 pF
BOM Maximum VO(PP) = 4.6 V, AV= 1,
output-swing RL= 10 kΩCL= 100 25°C 0.54 0.54 MHz
bandwidth pF
AV= -1, To 0.1% 1.5 1.5
Step = -2.3 V to
tsSettling time 2.3 V, 25°Cμs
To 0.01% 3.2 3.2
RL= 10 kΩ
CL= 100 pF
φmPhase margin at 25°C 52°52°
CL= 100
unity gain RL= 10 kΩ,pF
Gain margin 25°C 10 10 dB
(1) Full range is −40°C to 125°C for Q level part.
Copyright ©2003–2012, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Link(s): TLC2272-Q1 TLC2272A-Q1 TLC2274-Q1 TLC2274A-Q1
TLC2272-Q1 , TLC2272A-Q1
TLC2274-Q1, TLC2274A-Q1
SGLS007E –FEBRUARY 2003–REVISED JANUARY 2012
www.ti.com
TLC2274Q ELECTRICAL CHARACTERISTICS
at specified free-air temperature, VDD = 5 V (unless otherwise noted) TLC2274Q TLC2274AQ
PARAMETER TEST CONDITIONS TA(1) UNIT
MIN TYP MAX MIN TYP MAX
25°C 300 2500 300 950
VIO Input offset voltage μV
Full range 3000 1600
Temperature coefficient of
αVIO 25°C to 125°C 2 2 μV/°C
input offset voltage
Input offset voltage μV/m
VIC = 0 V, VDD±=±2.5 V, 25°C 0.002 0.002
long-term drift(2) o
VO= 0 V, RS= 50 Ω
25°C 0.5 60 0.5 60
IIO Input offset current pA
Full range 800 800
25°C 1 1 60
IIB Input bias current pA
Full range 800
−0.3 to −0.3 to
25°C 0 to 4 0 to 4
4.2 4.2
Common-mode input
VICR RS= 50 Ω|VIO|≤5 mV V
voltage range 0 to
Full range 0 to 3.5 3.5
IOH =−20 μA 25°C 4.99 4.99
25°C 4.85 4.93 4.85 4.93
IOH =−200 μA
VOH High-level output voltage Full range 4.85 4.85 V
25°C 4.25 4.65 4.25 4.65
IOH =−1 mA Full range 4.25 4.25
VIC = 2.5 V, IOL = 50 μA 25°C 0.01 0.01
25°C 0.09 0.15 0.09 0.15
VIC = 2.5 V, IOL = 500 μA
VOL Low-level output voltage Full range 0.15 0.15 V
25°C 0.9 1.5 0.9 1.5
VIC = 2.5 V, IOL = 5 mA Full range 1.5 1.5
25°C 10 35 10 35
VIC = 2.5 V, RL= 10 kΩ(3)
Large-signal differential
AVD VO= 1 V to 4 Full range 10 10 V/mV
voltage amplification V, RL= 1 MΩ(3) 25°C 175 175
Differential input
rid 25°CΩ
1012 1012
resistance
Common-mode input
ri25°CΩ
1012 1012
resistance
Common-mode input f = 10 kHz, N package
ci25°C 8 8 pF
capacitance
Closed-loop output f = 1 MHz, AV= 10
zo25°C 140 140 Ω
impedance
VIC = 0 V to 2.7 RS= 50 Ω25°C 70 75 70 75
CMR Common-mode rejection V, dB
R ratio Full range 70 70
VO= 2.5 V,
VDD = 4.4 V to 16 V, 25°C 80 95 80 95
Supply voltage rejection
kSVR dB
ratio (ΔVDD/ΔVIO)VIC = VDD/2, No load Full range 80 80
25°C 4.4 6 4.4 6
IDD Supply current VO= 2.5 V, No load mA
Full range 6 6
(1) Full range is −40°C to 125°C for Q level part.
(2) Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA= 150°C extrapolated to
TA= 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
(3) Referenced to 2.5 V
8Submit Documentation Feedback Copyright ©2003–2012, Texas Instruments Incorporated
Product Folder Link(s): TLC2272-Q1 TLC2272A-Q1 TLC2274-Q1 TLC2274A-Q1
TLC2272-Q1 , TLC2272A-Q1
TLC2274-Q1, TLC2274A-Q1
www.ti.com
SGLS007E –FEBRUARY 2003–REVISED JANUARY 2012
TLC2274Q OPERATING CHARACTERISTICS
at specified free-air temperature, VDD = 5 V (unless otherwise noted) TLC2274Q TLC2274AQ
PARAMETER TEST CONDITIONS TA(1) UNIT
MIN TYP MAX MIN TYP MAX
VO= 0.5 V to CL= 100 pF(2) 25°C 2.3 3.6 2.3 3.6
SR Slew rate at unity gain 2.5 V, V/μs
Full range 1.7 1.7
RL= 10 kΩ(2)
f = 10 Hz 25°C 50 50
Equivalent input noise nV/√
Vnvoltage Hz
f = 1 kHz 25°C 9 9
f = 0.1 to 1 Hz 25°C 1 1
Peak-to-peak equivalent
VN(pp) μV
input noise voltage f = 0.1 to 10 Hz 25°C 1.4 1.4
Equivalent input noise fA/√H
In25°C 0.6 0.6
current z
VO= 0.5V to AV= 1 0.0013 0.0013
2.5V, % %
THD Total harmonic distortion RL= 10 kΩ,25°C
+ N plus noise AV= 10 0.004% 0.004%
f = 20 kHz (2)
AV= 100 0.03% 0.03%
Gain-bandwidth product f = 10 kHz, RL= 10 kΩ(2) 25°C 2.18 2.18 MHz
CL= 100 pF(2)
BOM Maximum output-swing VO(PP) = 2V, AV= 1, 25°C 1 1 MHz
bandwidth RL= 10 kΩ(2) CL= 100 pF(2)
AV= -1, To 0.1% 1.5 1.5
Step = 0.5V to
tsSettling time 2.5V, 25°Cμs
To 0.01% 2.6 2.6
RL= 10 kΩ(3)
CL= 100 pF(3)
φmPhase margin at unity gain 25°C 50°50°
RL= 10 kΩ(3), CL= 100 pF(3)
Gain margin 25°C 10 10 dB
(1) Full range is −40°C to 125°C for Q level part.
(2) Referenced to 2.5 V
(3) Referenced to 2.5 V
Copyright ©2003–2012, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Link(s): TLC2272-Q1 TLC2272A-Q1 TLC2274-Q1 TLC2274A-Q1
TLC2272-Q1 , TLC2272A-Q1
TLC2274-Q1, TLC2274A-Q1
SGLS007E –FEBRUARY 2003–REVISED JANUARY 2012
www.ti.com
TLC2274Q ELECTRICAL CHARACTERISTICS
at specified free-air temperature, VDD±=±5 V (unless otherwise noted) TLC2274Q TLC2274AQ
PARAMETER TEST CONDITIONS TA(1) UNIT
MIN TYP MAX MIN TYP MAX
25°C 300 2500 300 950
VIO Input offset voltage μV
Full range 3000 1500
Temperature
αVIO coefficient of input 25°C to 125°C 2 2 μV/°C
offset voltage VIC = 0 V,
Input offset voltage μV/m
VO= 0 V 25°C 0.002 0.002
RS= 50 Ω
long-term drift(2) o
25°C 0.5 60 0.5 60
IIO Input offset current pA
Full range 800 800
25°C 1 60 1 60
IIB Input bias current pA
Full range 800 800
−5.3 to −5.3 to
25°C−5 to 4 −5 to 4
4.2 4.2
Common-mode input |VIO|≤5
VICR RS= 50 ΩV
voltage range mV −5 to
Full range −5 to 3.5
3.5
IO=−20 μA 25°C 4.99 4.99
25°C 4.85 4.93 4.85 4.93
IO=−200 μA
Maximum positive
VOM+ Full range 4.85 4.85 V
peak output voltage 25°C 4.25 4.65 4.25 4.65
IO=−1 mA Full range 4.25 4.25
VIC = 0 V, IO= 50 μA 25°C−4.99 −4.99
25°C−4.85 −4.91 −4.85 −4.91
IO= 500
VIC = 0 V,
Maximum negative μA
VOM- Full range −4.85 −4.85 V
peak output voltage 25°C−3.5 −4.1 −3.5 −4.1
VIC = 0 V, IO= 5 mA Full range −3.5 −3.5
25°C 20 50 20 50
Large-signal RL= 10 kΩ
AVD differential voltage VO=±4 V, Full range 20 20 V/mV
amplification RL= 1 MΩ25°C 300 300
Differential input
rid 25°CΩ
1012 1012
resistance
Common-mode input
ri25°CΩ
1012 1012
resistance
Common-mode input f = 10 kHz, N package
ci25°C 8 8 pF
capacitance
Closed-loop output f = 1 MHz, AV = 10
zo25°C 130 130 Ω
impedance
VIC = -5 V to RS= 50 Ω25°C 75 80 75 80
CMR Common-mode 2.7 V, dB
R rejection ratio Full range 75 75
VO= 0 V,
Supply voltage VDD =±2.2 V to ±8 V, 25°C 80 95 80 95
kSVR rejection ratio dB
VIC = 0V, No load Full range 80 80
(ΔVDD/ΔVIO)
25°C 4.4 6 4.4 6
IDD Supply current VO= 0 V, No load mA
Full range 6 6
(1) Full range is −40°C to 125°C for Q level part.
(2) Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at TA= 150°C extrapolated to
TA= 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
10 Submit Documentation Feedback Copyright ©2003–2012, Texas Instruments Incorporated
Product Folder Link(s): TLC2272-Q1 TLC2272A-Q1 TLC2274-Q1 TLC2274A-Q1
TLC2272-Q1 , TLC2272A-Q1
TLC2274-Q1, TLC2274A-Q1
www.ti.com
SGLS007E –FEBRUARY 2003–REVISED JANUARY 2012
TLC2274Q OPERATING CHARACTERISTICS
at specified free-air temperature, VDD±=±5 V (unless otherwise noted) TLC2274Q TLC2274AQ
PARAMETER TEST CONDITIONS TA(1) UNIT
MIN TYP MAX MIN TYP MAX
VO=±2.3 V, CL= 100 25°C 2.3 3.6 2.3 3.6
Slew rate at unity
SR V/μs
RL= 10 kΩpF
gain Full range 1.7 1.7
f = 10 Hz 25°C 50 50
Equivalent input nV/√H
Vnnoise voltage z
f = 1 kHz 25°C 9 9
Peak-to-peak f = 0.1 to 1 Hz 25°C 1 1
VN(pp) equivalent input μV
f = 0.1 to 10 Hz 25°C 1.4 1.4
noise voltage
Equivalent input fA/√H
In25°C 0.6 0.6
noise current z
AV= 1 0.0011% 0.0011%
VO=±2.3 V,
THD Total harmonic f = 20 kHz, AV= 10 25°C 0.004% 0.004%
+ N distortion plus noise RL= 10 kΩAV= 100 0.03% 0.03%
Gain-bandwidth f = 10 kHz, RL= 10 kΩ25°C 2.25 2.25 MHz
product CL= 100 pF
BOM Maximum VO(PP) = 4.6 V, AV= 1,
output-swing RL= 10 kΩCL= 100 25°C 0.54 0.54 MHz
bandwidth pF
AV= -1, To 0.1% 1.5 1.5
Step = -2.3 V to
tsSettling time 2.3 V, 25°Cμs
To 0.01% 3.2 3.2
RL= 10 kΩ
CL= 100 pF
φmPhase margin at 25°C 52°52°
CL= 100
unity gain RL= 10 kΩ,pF
Gain margin 25°C 10 10 dB
(1) Full range is −40°C to 125°C for Q level part.
Copyright ©2003–2012, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Link(s): TLC2272-Q1 TLC2272A-Q1 TLC2274-Q1 TLC2274A-Q1
TLC2272-Q1 , TLC2272A-Q1
TLC2274-Q1, TLC2274A-Q1
SGLS007E –FEBRUARY 2003–REVISED JANUARY 2012
www.ti.com
TYPICAL CHARACTERISTICS
Table of Graphs(1)
FIGURE
Figure 1,Figure 2,
VIO Input offset voltage Distribution vs Common-mode voltage Figure 3,Figure 4,
Figure 5,Figure 6
Input offset voltage temperature coefficient Distribution Figure 7,Figure 8,
αVIO Figure 9,Figure 10
IIB /IIO Input bias and input offset current vs Free-air temperature Figure 11
vs Supply voltage Figure 12
VIInput voltage vs Free-air temperature Figure 13
VOH High-level output voltage vs High-level output current Figure 14
VOL Low-level output voltage vs Low-level output current Figure 15,Figure 16
VOM + Maximum positive peak output voltage vs Output current Figure 17
VOM −Maximum negative peak output voltage vs Output current Figure 18
VO(PP) Maximum peak-to-peak output voltage vs Frequency Figure 19
vs Supply voltage Figure 20
IOS Short-circuit output current vs Free-air temperature Figure 21
VOOutput voltage vs Differential input voltage Figure 22,Figure 23
AVD Large-signal differential voltage amplification vs Load resistance Figure 24
Large-signal differential voltage amplification and phase vs Frequency Figure 25,Figure 26
margin
Large-signal differential voltage amplification vs Free-air temperature Figure 27,Figure 28
zo Output impedance vs Frequency Figure 29,Figure 30
vs Frequency Figure 31
CMRR Common-mode rejection ratio vs Free-air temperature Figure 32
vs Frequency Figure 33,Figure 34
kSVR Supply-voltage rejection ratio vs Free-air temperature Figure 35
vs Supply voltage Figure 36,Figure 37
IDD Supply current vs Free-air temperature Figure 38,Figure 39
vs Load capacitance Figure 40
SR Slew rate vs Free-air temperature Figure 41
Inverting large-signal pulse response Figure 42,Figure 43
Voltage-follower large-signal pulse response Figure 44,Figure 45
VOInverting small-signal pulse response Figure 46,Figure 47
Voltage-follower small-signal pulse response Figure 48,Figure 49
VnEquivalent input noise voltage vs Frequency Figure 50,Figure 51
Noise voltage over a 10-second period Figure 52
Integrated noise voltage vs Frequency Figure 53
THD + N Total harmonic distortion plus noise vs Frequency Figure 54
vs Supply voltage Figure 55
Gain bandwidth product Gain-bandwidth product vs Free-air temperature Figure 56
φmPhase margin vs Load capacitance Figure 57
Gain margin vs Load capacitance Figure 58
(1) For all graphs where VDD = 5 V, all loads are referenced to 2.5 V.
12 Submit Documentation Feedback Copyright ©2003–2012, Texas Instruments Incorporated
Product Folder Link(s): TLC2272-Q1 TLC2272A-Q1 TLC2274-Q1 TLC2274A-Q1
VIO − Input Offset V oltage − mV
Percentage of Amplifiers − %
10
5
0
20
15
0 0.4 0.8 1.2 1.6
992 Amplifiers From
−1.6 −1.2 −0.8 −0.4
2 Wafer Lots
VDD = ±2.5 V
VIO − Input Offset V oltage − mV
Percentage of Amplifiers − %
10
5
0
20
15
0 0.4 0.8 1.2 1.6
992 Amplifiers From
−1.6 −1.2 −0.8 −0.4
2 Wafer Lots
VDD = ±5 V
TLC2272-Q1 , TLC2272A-Q1
TLC2274-Q1, TLC2274A-Q1
www.ti.com
SGLS007E –FEBRUARY 2003–REVISED JANUARY 2012
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various
devices.
DISTRIBUTION OF TLC2272 INPUT OFFSET VOLTAGE DISTRIBUTION OF TLC2272 INPUT OFFSET VOLTAGE
Figure 1. Figure 2.
DISTRIBUTION OF TLC2274 INPUT OFFSET VOLTAGE DISTRIBUTION OF TLC2274A INPUT OFFSET VOLTAGE
Figure 3. Figure 4.
Copyright ©2003–2012, Texas Instruments Incorporated Submit Documentation Feedback 13
Product Folder Link(s): TLC2272-Q1 TLC2272A-Q1 TLC2274-Q1 TLC2274A-Q1
0.5
0
−1
−1 0 1
VIO − Input Offset V oltage − mV
1
2345
VIO
VIC − Common-Mode V oltage − V
VDD = 5 V
TA= 25°C
RS= 50 Ω
−0.5
0.5
0
−1
−1 0 1
VIO − Input Offset V oltage − mV
1
2 3 4 5
VIC − Common-Mode V oltage − V
VIO
−0.5
VDD = ±5 V
TA= 25°C
RS= 50 Ω
−6 −5 −4 −3 −2
TLC2272-Q1 , TLC2272A-Q1
TLC2274-Q1, TLC2274A-Q1
SGLS007E –FEBRUARY 2003–REVISED JANUARY 2012
www.ti.com
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various
devices. INPUT OFFSET VOLTAGE INPUT OFFSET VOLTAGE
vs vs
COMMON-MODE VOLTAGE COMMON-MODE VOLTAGE
Figure 5. Figure 6.
DISTRIBUTION OF TLC2272 DISTRIBUTION OF TLC2272
vs vs
INPUT OFFSET VOLTAGE TEMPERATURE COEFFICIENT INPUT OFFSET VOLTAGE TEMPERATURE COEFFICIENT
Figure 7. Figure 8.
14 Submit Documentation Feedback Copyright ©2003–2012, Texas Instruments Incorporated
Product Folder Link(s): TLC2272-Q1 TLC2272A-Q1 TLC2274-Q1 TLC2274A-Q1
15
10
5
0
0 1
Percentage of Amplifiers − %
20
25
2 3 4 5
αVIO − Temperature Coefficient − µV/°C
−5 −4 −3 −2 −1
128 Amplifiers From
2 Wafer Lots
VDD = ±2.5 V
N Package
TA= 25°C to 125°C
15
10
5
0
Percentage of Amplifiers − %
20
25
αVIO − Temperature Coefficient − µV/°C
0 1 2 3 4 5
−5 −4 −3 −2 −1
128 Amplifiers From
2 Wafer Lots
VDD = ±2.5 V
N Package
TA= 25°C to 125°C
0
− 2
− 6
− 8
− 10
8
− 4
2 3 4 5 6 7 8
− Input Voltage − V
4
2
6
10
|VDD ±| − Supply Voltage − V
VI
TA= 25°C
RS= 50 Ω
|VIO|≤5mV
12
TLC2272-Q1 , TLC2272A-Q1
TLC2274-Q1, TLC2274A-Q1
www.ti.com
SGLS007E –FEBRUARY 2003–REVISED JANUARY 2012
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various
devices. DISTRIBUTION OF TLC2274A DISTRIBUTION OF TLC2274A
vs vs
INPUT OFFSET VOLTAGE TEMPERATURE COEFFICIENT INPUT OFFSET VOLTAGE TEMPERATURE COEFFICIENT
Figure 9. Figure 10.
INPUT BIAS AND INPUT OFFSET CURRENT INPUT VOLTAGE
vs vs
FREE-AIR TEMPERATURE SUPPLY VOLTAGE
Figure 11. Figure 12.
Copyright ©2003–2012, Texas Instruments Incorporated Submit Documentation Feedback 15
Product Folder Link(s): TLC2272-Q1 TLC2272A-Q1 TLC2274-Q1 TLC2274A-Q1
−75 − 25 0 25 50 75 100 125
2
1
0
−1
3
4
5
− Input Voltage − VVI
TA− Free-Air Temperature − °C
|VIO|≤5mV
VDD = 5 V
− 50
V0H − High-Level Output V oltage − V
VOH
IOH − High-Level Output Current − mA
4
2
1
0
6
3
0 1 2 3 4
5
VDD = 5 V
TA= 125°C
TA= −55°C
TA= 25°C
VOL − Low-Level Output V oltage − V
IOL − Low-Level Output Current − mA
VOL
0.6
0.4
0.2
0
0 1 2 3
0.8
4
1
1.2
5 6
1.4 VDD = 5 V
VIC = 2.5 V
TA= 125°C
TA= 25°C
TA= −55°C
VOL − Low-Level Output V oltage − V
0.6
0.4
0.2
0
0 1 2 3
0.8
4 5
VDD = 5 V
TA= 25°C
IOL − Low-Level Output Current − mA
VOL
VIC = 1.25 V
1
1.2
VIC = 2.5 V
VIC = 0 V
TLC2272-Q1 , TLC2272A-Q1
TLC2274-Q1, TLC2274A-Q1
SGLS007E –FEBRUARY 2003–REVISED JANUARY 2012
www.ti.com
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various
devices. INPUT VOLTAGE HIGH-LEVEL OUTPUT VOLTAGE
vs vs
FREE-AIR TEMPERATURE HIGH-LEVEL OUTPUT CURRENT
Figure 13. Figure 14.
LOW-LEVEL OUTPUT VOLTAGE LOW-LEVEL OUTPUT VOLTAGE
vs vs
LOW-LEVEL OUTPUT CURRENT LOW-LEVEL OUTPUT CURRENT
Figure 15. Figure 16.
16 Submit Documentation Feedback Copyright ©2003–2012, Texas Instruments Incorporated
Product Folder Link(s): TLC2272-Q1 TLC2272A-Q1 TLC2274-Q1 TLC2274A-Q1
0 1 2 3 4 5 6
IO− Output Current − mA
VDD = ± 5 V
VIC = 0 V
TA= 125°C
TA= 25°C
TA= −55°C
−3.8
−4
−4.2
−4.4
−4.6
−4.8
−5
− Maximum Negative Peak Output V oltage − V
VOM −
3
2
1
0 1 2 3 4 5
− Maximum Positive Peak Output V oltage − V
4
5
|IO| − Output Current − mA
TA= −55°C
TA= 25°C
TA= 125°C
VDD ± = ±5 V
VOM +
4
0
2 3 4
8
12
16
5678
IOS − Short-Circuit Output Current − mA
OS
I
|VDD ±| − Supply Voltage − V
VID = 100 mV
VO= 0 V
TA= 25°C
−8
VID = −100 mV
−4
2
1
0
10 k 100 k 1 M
3
f − Frequency − Hz
4
10 M
6
5
7
8
9
10
V(OPP) − Maximum Peak-to-Peak Output V oltage − VVO(PP)
VDD = 5 V
VDD = ±5 V
RL= 10 kΩ
TA= 25°C
TLC2272-Q1 , TLC2272A-Q1
TLC2274-Q1, TLC2274A-Q1
www.ti.com
SGLS007E –FEBRUARY 2003–REVISED JANUARY 2012
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various
devices. MAXIMUM POSITIVE PEAK OUTPUT VOLTAGE MAXIMUM NEGATIVE PEAK OUTPUT VOLTAGE
vs vs
OUTPUT CURRENT OUTPUT CURRENT
Figure 17. Figure 18.
MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE SHORT-CIRCUIT OUTPUT CURRENT
vs vs
FREQUENCY SUPPLY VOLTAGE
Figure 19. Figure 20.
Copyright ©2003–2012, Texas Instruments Incorporated Submit Documentation Feedback 17
Product Folder Link(s): TLC2272-Q1 TLC2272A-Q1 TLC2274-Q1 TLC2274A-Q1
−5
−75 −50 −25 0 25 50 75 100 125
−1
−3
7
11
15
IOS − Short-Circuit Output Current − mA
OS
I
TA− Free-Air Temperature − °C
VID = 100 mV
VID = −100 mV
VO= 0 V
VDD = ± 5 V
3
2
1
0
800
4
5
1200
VID − Differential Input V oltage − µV
− Output Voltage − V
VO
−800 −400 4000
VDD = 5 V
TA= 25°C
RL= 10 kΩ
VIC = 2.5 V
1
−1
−3
−5 0 250
3
5
500 750 1000
VID − Differential Input V oltage − µV
− Output Voltage − V
VO
−1000 −750 −250−500
VDD = ± 5 V
TA= 25°C
RL= 10 kΩ
VIC = 0 V
0.1
1
0.1 1 10 100
10
100
1000
RL− Load Resistance − k Ω
VO= ± 1 V
TA= 25°C
VDD = ±5 V
VDD = 5 V
AVD − Large-Signal DifferentialAVD
Voltage Amplification − dB
TLC2272-Q1 , TLC2272A-Q1
TLC2274-Q1, TLC2274A-Q1
SGLS007E –FEBRUARY 2003–REVISED JANUARY 2012
www.ti.com
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various
devices. SHORT-CIRCUIT OUTPUT CURRENT OUTPUT VOLTAGE
vs vs
FREE-AIR TEMPERATURE DIFFERENTIAL INPUT VOLTAGE
Figure 21. Figure 22.
LARGE-SIGNAL DIFFERENTIAL VOLTAGE
OUTPUT VOLTAGE AMPLIFICATION
vs vs
DIFFERENTIAL INPUT VOLTAGE LOAD RESISTANCE
Figure 23. Figure 24.
18 Submit Documentation Feedback Copyright ©2003–2012, Texas Instruments Incorporated
Product Folder Link(s): TLC2272-Q1 TLC2272A-Q1 TLC2274-Q1 TLC2274A-Q1
0
20
1 k 10 k 100 k 1 M
40
60
80
f − Frequency − Hz
10 M
VDD = ±5 V
RL= 10 kΩ
CL= 100 pF
TA= 25°C
om − Phase Margin
φm
−20
−40 −90°
−45°
0°
45°
90°
135°
180°
AVD − Large-Signal DifferentialAVD
Voltage Amplification − dB
0
20
1 k 10 k 100 k 1 M
40
60
80
f − Frequency − Hz
10 M
om − Phase Margin
φm
VDD = 5 V
RL= 10 kΩ
CL= 100 pF
TA= 25°C
−20
−40 −90°
−45°
0°
45°
90°
135°
180°
AVD − Large-Signal Differential
AVD
Voltage Amplification − dB
−75 −50 −25 0 25 50 75 100 125
10
100
1 k
TA− Free-Air Temperature − °C
VDD = 5 V
VIC = 2.5 V
VO= 1 V to 4 V
RL= 1 MΩ
RL= 10 kΩ
AVD − Large-Signal DifferentialAVD
Voltage Amplification − V/mV
−75 −50 −25 0 25 50 75 100 125
10
100
1 k
TA− Free-Air Temperature − °C
RL= 1 MΩ
RL= 10 kΩ
VDD = ± 5 V
VIC = 0 V
VO= ± 4 V
AVD − Large-Signal DifferentialAVD
Voltage Amplification − V/mV
TLC2272-Q1 , TLC2272A-Q1
TLC2274-Q1, TLC2274A-Q1
www.ti.com
SGLS007E –FEBRUARY 2003–REVISED JANUARY 2012
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various
devices. LARGE-SIGNAL DIFFERENTIAL VOLTAGE LARGE-SIGNAL DIFFERENTIAL VOLTAGE
AMPLIFICATION AND PHASE MARGIN AMPLIFICATION AND PHASE MARGIN
vs vs
FREQUENCY FREQUENCY
Figure 25. Figure 26.
LARGE-SIGNAL DIFFERENTIAL VOLTAGE LARGE-SIGNAL DIFFERENTIAL VOLTAGE
AMPLIFICATION AMPLIFICATION
vs vs
FREE-AIR TEMPERATURE FREE-AIR TEMPERATURE
Figure 27. Figure 28.
Copyright ©2003–2012, Texas Instruments Incorporated Submit Documentation Feedback 19
Product Folder Link(s): TLC2272-Q1 TLC2272A-Q1 TLC2274-Q1 TLC2274A-Q1
10
1
0.1
1000
100
100 1 k 10 k 100 k 1 M
zo − Output Impedance − W
f − Frequency − Hz
VDD = 5 V
TA= 25°C
AV= 100
AV= 10
AV= 1
10
1
0.1
1000
100
100 1 k 10 k 100 k 1 M
zo − Output Impedance − W
f − Frequency − Hz
VDD = ± 5 V
TA= 25°C
AV= 100
AV= 10
AV= 1
60
40
20
010 100 1 k 10 k
CMRR − Common-Mode Rejection Ratio − dB
80
100
100 k 1 M
f − Frequency − Hz
VDD = ± 5 V
VDD = 5 V
10 M
TA= 25°C
TA− Free-Air Temperature − °C
CMRR − Common-Mode Rejection Ratio − dB
82
78
74
70
86
90
−75 −50 −25 0 25 50 75 100 125
VDD = ± 5 V
VDD = 5 V
VIC = 0 V to 2.7 V
VIC = −5 V to 2.7 V
TLC2272-Q1 , TLC2272A-Q1
TLC2274-Q1, TLC2274A-Q1
SGLS007E –FEBRUARY 2003–REVISED JANUARY 2012
www.ti.com
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various
devices. OUTPUT IMPEDANCE OUTPUT IMPEDANCE
vs vs
FREQUENCY FREQUENCY
Figure 29. Figure 30.
COMMON-MODE REJECTION RATIO COMMON-MODE REJECTION RATIO
vs vs
FREQUENCY FREE-AIR TEMPERATURE
Figure 31. Figure 32.
20 Submit Documentation Feedback Copyright ©2003–2012, Texas Instruments Incorporated
Product Folder Link(s): TLC2272-Q1 TLC2272A-Q1 TLC2274-Q1 TLC2274A-Q1
40
20
0
10 100 1 k
kSVR − Supply-Voltage Rejection Ratio − dB
60
80
f − Frequency − Hz
100
10 k 100 k 1 M 10 M
kSVR
VDD = 5 V
TA= 25°C
kSVR+
kSVR −
−20
40
20
0
10 100 1 k
kSVR − Supply-Voltage Rejection Ratio − dB
60
80
f − Frequency − Hz
100
10 k 100 k 1 M 10 M
kSVR
VDD = ± 5 V
TA= 25°C
kSVR+
kSVR −
−20
kSVR − Supply Voltage Rejection Ratio − dB
kSVR
TA− Free-Air Temperature − °C
−75 −50 −25 0 25 50 75 100 125
100
95
90
85
105
110
VDD ± = ±2.2 V to ±8 V
VO= 0 V
TLC2272-Q1 , TLC2272A-Q1
TLC2274-Q1, TLC2274A-Q1
www.ti.com
SGLS007E –FEBRUARY 2003–REVISED JANUARY 2012
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various
devices. SUPPLY-VOLTAGE REJECTION RATIO SUPPLY-VOLTAGE REJECTION RATIO
vs vs
FREQUENCY FREQUENCY
Figure 33. Figure 34.
SUPPLY-VOLTAGE REJECTION RATIO TLC2272 SUPPLY CURRENT
vs vs
FREE-AIR TEMPERATURE SUPPLY VOLTAGE
Figure 35. Figure 36.
Copyright ©2003–2012, Texas Instruments Incorporated Submit Documentation Feedback 21
Product Folder Link(s): TLC2272-Q1 TLC2272A-Q1 TLC2274-Q1 TLC2274A-Q1
0 1 2 3 4 5 6 7 8
0
1.2
2.4
3.6
4.8
6
IDD − Supply Current − mA
DD
I
|VDD ±| − Supply Voltage − V
VO= 0 V
No Load
TA= 25°C
TA= −55°C
TA= 125°C
µ s
SR − Slew Rate − V/
0
1
2
3
CL− Load Capacitance − pF
10 k1 k10010
SR +
SR −
4
5
VDD = 5 V
AV= −1
TA= 25°C
−75 −50 −25 0 25 50 75 100 125
0
1.2
2.4
3.6
4.8
6
TA− Free-Air Temperature − °C
IDD − Supply Current − mA
DD
I
VDD = 5 V
VO= 2.5 V
VDD = ±5 V
VO= 0 V
TLC2272-Q1 , TLC2272A-Q1
TLC2274-Q1, TLC2274A-Q1
SGLS007E –FEBRUARY 2003–REVISED JANUARY 2012
www.ti.com
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various
devices. TLC2274A SUPPLY CURRENT TLC2272 SUPPLY CURRENT
vs vs
SUPPLY VOLTAGE FREE-AIR TEMPERATURE
Figure 37. Figure 38.
TLC2274A SUPPLY CURRENT SLEW RATE
vs vs
FREE-AIR TEMPERATURE LOAD CAPACITANCE
Figure 39. Figure 40.
22 Submit Documentation Feedback Copyright ©2003–2012, Texas Instruments Incorporated
Product Folder Link(s): TLC2272-Q1 TLC2272A-Q1 TLC2274-Q1 TLC2274A-Q1
2
1
01 2 3 4 5
3
4
5
6 7 8 9
VO − Output Voltage − mV
VO
t − Time − µs
VDD = 5 V
RL= 10 kΩ
CL= 100 pF
TA= 25°C
AV= −1
0
3
2
1
4
µs
SR − Slew Rate − V/
−75 −50 −25 0 25 50 75 100 125
TA− Free-Air Temperature − °C
VDD = 5 V
RL= 10 kΩ
CL= 100 pF
AV= 1
SR +
SR −
0
5
0
− 1
− 3
− 4
− 5
4
− 2
12345
2
1
3
5
6 7 8 9
VO − Output Voltage − V
VO
t − Time − µs
VDD = ± 5 V
RL= 10 kΩ
CL= 100 pF
TA= 25°C
AV= −1
0
3
2
1
01 2 3 4 5
4
5
6 7 8 9
VO − Output Voltage − V
VO
t − Time − µs
VDD = 5 V
RL= 10 kΩ
CL= 100 pF
AV= 1
TA= 25°C
0
TLC2272-Q1 , TLC2272A-Q1
TLC2274-Q1, TLC2274A-Q1
www.ti.com
SGLS007E –FEBRUARY 2003–REVISED JANUARY 2012
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various
devices. SLEW RATE
vs
FREE-AIR TEMPERATURE INVERTING LARGE-SIGNAL PULSE RESPONSE
Figure 41. Figure 42.
VOLTAGE-FOLLOWER LARGE-SIGNAL PULSE
INVERTING LARGE-SIGNAL PULSE RESPONSE RESPONSE
Figure 43. Figure 44.
Copyright ©2003–2012, Texas Instruments Incorporated Submit Documentation Feedback 23
Product Folder Link(s): TLC2272-Q1 TLC2272A-Q1 TLC2274-Q1 TLC2274A-Q1
2.5
2.45
2.4 0.5 1 1.5 2 2.5
2.55
2.6
2.65
3.5 4.5 5 5.5
− Output Voltage − V
VO
t − Time − µs
VDD = 5 V
RL= 10 kΩ
CL= 100 pF
TA= 25°C
AV= −1
034
0
−1
4
12345
2
1
3
5
6 7 8 9
VO − Output Voltage − V
VO
t − Time − µs
VDD = ±5 V
RL= 10 kΩ
CL= 100 pF
TA= 25°C
AV= 1
0
−2
−3
−5
−4
0
−100 0 0.5 1 1.5 2
50
100
2.5 3 3.5 4
VO − Output Voltage − mV
VO
t − Time − µs
VDD = ± 5 V
RL= 10 kΩ
CL= 100 pF
TA= 25°C
AV= 1
−50
2.5
2.45
2.4
2.55
2.6
0 0.5 1 1.5
VO − Output Voltage − V
VO
t − Time − µs
2.65
VDD = 5 V
RL= 10 kΩ
CL= 100 pF
TA= 25°C
AV= 1
TLC2272-Q1 , TLC2272A-Q1
TLC2274-Q1, TLC2274A-Q1
SGLS007E –FEBRUARY 2003–REVISED JANUARY 2012
www.ti.com
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various
devices. VOLTAGE-FOLLOWER LARGE-SIGNAL PULSE
RESPONSE INVERTING SMALL-SIGNAL PULSE RESPONSE
Figure 45. Figure 46.
VOLTAGE-FOLLOWER SMALL-SIGNAL PULSE
INVERTING SMALL-SIGNAL PULSE RESPONSE RESPONSE
Figure 47. Figure 48.
24 Submit Documentation Feedback Copyright ©2003–2012, Texas Instruments Incorporated
Product Folder Link(s): TLC2272-Q1 TLC2272A-Q1 TLC2274-Q1 TLC2274A-Q1
0
−50
−100
50
100
0 0.5 1 1.5
VO − Output Voltage − mV
VO
t − Time − µs
VDD = ±5 V
RL= 10 kΩ
CL= 100 pF
TA= 25°C
AV= 1
20
10
0
10 100 1 k
Vn − Equivalent Input Noise V oltage − nV Hz
30
f − Frequency − Hz
40
10 k
50
60
VnnV/ Hz
VDD = 5 V
TA= 25°C
RS= 20 Ω
−750
−1000 2 4 6
0
250
8 10
Noise Voltage − nV
t − Time − s
0
VDD = 5 V
f = 0.1 Hz to 10 Hz
TA= 25°C
500
750
1000
−250
−500
20
10
0
10 100 1 k
Vn − Equivalent Input Noise V oltage − nV Hz
30
f − Frequency − Hz
40
10 k
50
60
VnnV/ Hz
VDD = ±5 V
TA= 25°C
RS= 20 Ω
TLC2272-Q1 , TLC2272A-Q1
TLC2274-Q1, TLC2274A-Q1
www.ti.com
SGLS007E –FEBRUARY 2003–REVISED JANUARY 2012
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various
devices. EQUIVALENT INPUT NOISE VOLTAGE
vs
VOLTAGE-FOLLOWER SMALL-SIGNAL PULSE
RESPONSE FREQUENCY
Figure 49. Figure 50.
EQUIVALENT INPUT NOISE VOLTAGE
vs
FREQUENCY NOISE VOLTAGE OVER A 10 SECOND PERIOD
Figure 51. Figure 52.
Copyright ©2003–2012, Texas Instruments Incorporated Submit Documentation Feedback 25
Product Folder Link(s): TLC2272-Q1 TLC2272A-Q1 TLC2274-Q1 TLC2274A-Q1
Integrated Noise V oltage − uVRMS
1
0.1
100
1 10 100 1 k
f − Frequency − Hz
10 k 100 k
VRMS
µ
Calculated Using
Ideal Pass-Band Filter
Lower Frequency = 1 Hz
TA= 25°C
10
0.0001
0.001
100 1 k 10 k 100 k
THD + N − Total Harmonic Distortion Plus Noise − %
f − Frequency − Hz
0.01
0.1
1
VDD = 5 V
TA= 25°C
RL= 10 kΩ
AV= 100
AV= 10
AV= 1
Gain-Bandwidth Product − MHz
2.1
2
0 1 2 3 4 5
2.2
2.3
6 7 8
|VDD ±| − Supply Voltage − V
2.4
2.5
f = 10 kHz
RL= 10 kΩ
CL= 100 pF
TA= 25°C
−75 −50 −25 0 25 50 75 100 125
TA− Free-Air Temperature − °C
Gain-Bandwidth Product − MHz
1.8
1.6
1.4
2
2.4
2.2
2.6
2.8
3
VDD = 5 V
f = 10 kHz
RL= 10 kΩ
CL= 100 pF
TLC2272-Q1 , TLC2272A-Q1
TLC2274-Q1, TLC2274A-Q1
SGLS007E –FEBRUARY 2003–REVISED JANUARY 2012
www.ti.com
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various
devices. INTEGRATED NOISE VOLTAGE TOTAL HARMONIC DISTORTION PLUS NOISE
vs vs
FREQUENCY FREQUENCY
Figure 53. Figure 54.
GAIN-BANDWIDTH PRODUCT GAIN-BANDWIDTH PRODUCT
vs vs
SUPPLY VOLTAGE FREE-AIR TEMPERATURE
Figure 55. Figure 56.
26 Submit Documentation Feedback Copyright ©2003–2012, Texas Instruments Incorporated
Product Folder Link(s): TLC2272-Q1 TLC2272A-Q1 TLC2274-Q1 TLC2274A-Q1
3
0
10
Gain Margin − dB
6
9
10000
CL− Load Capacitance − pF
12
15
1000100
VDD = 5 V
AV= 1
RL= 10 kΩ
TA= 25°C
10
om − Phase Margin
10000
CL− Load Capacitance − pF
φm
1000100
VDD = ±5 V
TA= 25°C
Rnull = 20 Ω
Rnull = 10 Ω
Rnull = 0
75°
60°
45°
30°
15°
0°
10 kΩ
10 kΩ
VDD −
VDD +
Rnull
CL
VI
Rnull = 100 Ω
Rnull = 50 Ω
TLC2272-Q1 , TLC2272A-Q1
TLC2274-Q1, TLC2274A-Q1
www.ti.com
SGLS007E –FEBRUARY 2003–REVISED JANUARY 2012
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various
devices. PHASE MARGIN GAIN MARGIN
vs vs
LOAD CAPACITANCE LOAD CAPACITANCE
Figure 57. Figure 58.
Copyright ©2003–2012, Texas Instruments Incorporated Submit Documentation Feedback 27
Product Folder Link(s): TLC2272-Q1 TLC2272A-Q1 TLC2274-Q1 TLC2274A-Q1
OUT
+
−
+
−
+
−
+
−
+
−
+
−
+
−+
−
+−
.SUBCKT TLC227x 1 2 3 4 5
C1 11 1214E−12
C2 6 760.00E−12
DC 5 53DX
DE 54 5DX
DLP 90 91DX
DLN 92 90DX
DP 4 3DX
EGND 99 0POLY (2) (3,0) (4,) 0 .5 .5
FB 99 0POLY (5) VB VC VE VLP VLN 0
+ 984.9E3 −1E6 1E6 1E6 −1E6
GA 6 011 12 377.0E−6
GCM 0 6 10 99 134E−9
ISS 3 10DC 216.OE−6
HLIM 90 0VLIM 1K
J1 11 210 JX
J2 12 110 JX
R2 6 9100.OE3
RD1 60 112.653E3
RD2 60 122.653E3
R01 8 550
R02 7 9950
RP 3 44.310E3
RSS 10 99925.9E3
VAD 60 4−.5
VB 9 0DC 0
VC 3 53 DC .78
VE 54 4DC .78
VLIM 7 8DC 0
VLP 91 0DC 1.9
VLN 0 92DC 9.4
.MODEL DX D (IS=800.0E−18)
.MODEL JX PJF (IS=1.500E−12BETA=1.316E-3
+ VTO=−.270)
.ENDS
VCC +
RP
IN −
2
IN+
1
VCC −
VAD
RD1
11
J1 J2
10
RSS ISS
3
12
RD2
60
VE
54 DE
DP
VC
DC
4
C1
53
R2
6
9
EGND
VB
FB
C2
GCM GA VLIM
8
5
RO1
RO2
HLIM
90
DIP
91
DIN
92
VINVIP
99
7
TLC2272-Q1 , TLC2272A-Q1
TLC2274-Q1, TLC2274A-Q1
SGLS007E –FEBRUARY 2003–REVISED JANUARY 2012
www.ti.com
APPLICATION INFORMATION
Macromodel Information
Macromodel information provided was derived using Microsim Parts, the model generation software used with
Microsim PSpice. The Boyle macromodel(2) and subcircuit in Figure 59 are generated using the TLC227x typical
electrical and operating characteristics at TA= 25°C. Using this information, output simulations of the following
key parameters can be generated to a tolerance of 20% (in most cases):
(2) G. R. Boyle, B. M. Cohn, D. O. Pederson, and J. E. Solomon, “Macromodeling of Integrated Circuit Operational Amplifiers”, IEEE
Journal of Solid-State Circuits, SC-9, 353 (1974). •Unity-gain frequency
•Maximum positive output voltage swing •Common-mode rejection ratio
•Maximum negative output voltage swing •Phase margin
•Slew rate •DC output resistance
•Quiescent power dissipation •AC output resistance
•Input bias current •Short-circuit output current limit
•Open-loop voltage amplification
Figure 59. Boyle Macromodels and Subcircuit
28 Submit Documentation Feedback Copyright ©2003–2012, Texas Instruments Incorporated
Product Folder Link(s): TLC2272-Q1 TLC2272A-Q1 TLC2274-Q1 TLC2274A-Q1
TLC2272-Q1 , TLC2272A-Q1
TLC2274-Q1, TLC2274A-Q1
www.ti.com
SGLS007E –FEBRUARY 2003–REVISED JANUARY 2012
REVISION HISTORY
Changes from Revision D (March 2009) to Revision E Page
•Deleted ESD ratings table .................................................................................................................................................... 3
Copyright ©2003–2012, Texas Instruments Incorporated Submit Documentation Feedback 29
Product Folder Link(s): TLC2272-Q1 TLC2272A-Q1 TLC2274-Q1 TLC2274A-Q1
PACKAGE OPTION ADDENDUM
www.ti.com 12-Jan-2012
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status (1) Package Type Package
Drawing Pins Package Qty Eco Plan (2) Lead/
Ball Finish MSL Peak Temp (3) Samples
(Requires Login)
TLC2272AQDRG4Q1 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLC2272AQDRQ1 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLC2272AQPWRG4Q1 ACTIVE TSSOP PW 8 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLC2272AQPWRQ1 ACTIVE TSSOP PW 8 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLC2272QDRG4Q1 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLC2272QDRQ1 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLC2272QPWRG4Q1 ACTIVE TSSOP PW 8 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLC2272QPWRQ1 ACTIVE TSSOP PW 8 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLC2274AQDRG4Q1 ACTIVE SOIC D 14 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLC2274AQDRQ1 ACTIVE SOIC D 14 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLC2274AQPWRG4Q1 ACTIVE TSSOP PW 14 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLC2274AQPWRQ1 ACTIVE TSSOP PW 14 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLC2274QDRG4Q1 ACTIVE SOIC D 14 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLC2274QDRQ1 ACTIVE SOIC D 14 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLC2274QPWRG4Q1 ACTIVE TSSOP PW 14 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLC2274QPWRQ1 ACTIVE TSSOP PW 14 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
(1) The marketing status values are defined as follows:
PACKAGE OPTION ADDENDUM
www.ti.com 12-Jan-2012
Addendum-Page 2
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TLC2272-Q1, TLC2272A-Q1, TLC2274-Q1, TLC2274A-Q1 :
•Catalog: TLC2272, TLC2272A, TLC2274, TLC2274A
•Enhanced Product: TLC2272A-EP, TLC2274-EP, TLC2274A-EP
•Military: TLC2272M, TLC2272AM, TLC2274M, TLC2274AM
NOTE: Qualified Version Definitions:
•Catalog - TI's standard catalog product
•Enhanced Product - Supports Defense, Aerospace and Medical Applications
•Military - QML certified for Military and Defense Applications
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated