Basic Switch Common Accessories Separator (Sold Separately) To ensure a secure insulation distance, or if there are other metal parts or copper wire installed too close to the Switch, use the Switch with insulation guard or use a separator purchased separately to keep the insulation distance. List of models Applicable Switches Separator Separator Thickness (mm) Model V D3V-01 VX D2MV D2RV D2VW 0.18 SEPARATOR FOR V0.18 0.25 SEPARATOR FOR V0.25 SS SS-P D2S D2SW D2SW-P 0.18 SEPARATOR FOR SS0.18 0.4 SEPARATOR FOR SS0.4 Basic Switch Common Accessories Appearance Note. The Separator is made of EAVTC (epoxy alkyd/varnish tetron cloth) and has heat-resistant temperature of +130C. Dimensions (Unit: mm) SEPARATOR FOR V0.18 SEPARATOR FOR V0.25 3 2-3.2 dia. holes 14 8 10.30.1 24 22.20.1 11 38 SEPARATOR FOR SS0.18 SEPARATOR FOR SS0.4 2-2.6 dia. holes 12+0.28 -0.12 +0.23 7-0.17 9.50.1 21.6 7 B-149 Basic Switch Common Accessories Basic Switch Common Accessories Actuator (Sold Separately) Actuators are supplementary components used when operating the Switch using cams or dogs or when transmitting mechanical movements that are not in alignment with the switch plunger. The VAL models are suitable for cases where a Switch is operated by a rotary cam or sliding devices with relatively low operation frequency. The VAM models are designed to operate in reverse movements and have high shock and vibration resistance. Since the Overtravel (OT) of these models is rather large, they can be used for automatic control or door switches of machining tools. The VAV models can be used where a small Operating Force (OF) is required. These Actuators do not include Switches. 10.30.15 22.20.15 Note. Switches with the mounting holes shown in the diagram can be used except for special models. Dimensions (Unit: mm) / Operating Characteristics * Model numbers are for the Actuators only. The value given for operating characteristics are reference values. For operating characteristics of models not listed above, consult your OMRON sales representative. Leaf Spring Model VAL t=0.3, width 4.7* A 5.6 21.8 Operating characteristics Operating Force Releasing Force 5.10.1 FP OP 10.30.15 18.2 22.20.15 27.8 2.8 5.6 t=0.3* A 20.6 R2.4 4.7 5.8 5.1 OP 10.30.15 22.20.15 27.8 Roller Leaf Spring VAL2 VAL02 A FP 2.8 *Stainless-steel lever Operating characteristics 4.8 Operating Force Releasing Force 2-M3x16 * VAL2: polyacetal resin roller VAL02: Stainless-steel roller 0.8 mm 0.4 mm In the case of V-15-1A5 OF Max. 2.26 N {230 gf} RF Min. 0.49 N {50 gf} Overtravel OT Min. Movement Differential MD Max. 18.2 Note1. Unless otherwise specified, a tolerance of 0.4mm applies to all dimensions. Note2. The operating characteristics are for operation in the A direction ( ). B-150 OF Max. 2.26 N {230 gf} RF Min. 0.49 N {50 gf} 5.6 5.10.25 22.20.08 27.8 Operating Force Releasing Force In the case of V-15-1A5 Free Position FP Max. 22.9 mm Operating Position OP 20.50.8 mm Note. Pin plunger (Designed for models of OF 1.96 N {200 gf} or greater). 2-M3x16 4.8 dia.x4.8* 20.6 OP 10.30.05 Operating characteristics Overtravel OT Min. Movement Differential MD Max. 18.2 2.8 0.8 mm 0.4 mm Free Position FP Max. 17 mm Operating Position OP 14.90.5 mm Note. Pin plunger (Designed for models of OF 1.96 N {200 gf} or greater). *Stainless-steel lever Simulated Leaf Spring VAL12 FP OF Max. 2.26 N {230 gf} RF Min. 0.49 N {50 gf} Overtravel OT Min. Movement Differential MD Max. 2-M3x16 In the case of V-15-1A5 0.8 mm 0.4 mm Free Position FP Max. 22.6 mm Operating Position OP 20.50.5 mm Note. Pin plunger (Designed for models of OF 1.96 N {200 gf} or greater). Basic Switch Common Accessories t=1, width 4.9* R44.4 A 15.1 6 3.6 5.2 PT *Stainless-steel lever A 5.45 0.8* dia. R50 15.1 3.2 PT 5.6 OP 20.3 2.8 *Stainless-steel wire 27.8 Hinge Roller Lever VAV2 4.8 dia.x4.8* A PT R19 6 15.1 3.6 5.2 OP 2.8 20.3 *polyacetal resin roller Reverse Long Hinge Lever VAM A 15 R62 20.3 5 OP Reverse Hinge Lever VAM21 22.20.15 27.8 15 20.3 *Stainless-steel lever 5 22.20.15 27.8 In the case of V-15-1A5 Operating Force Releasing Force 0.74 N {75 gf} 0.09 N {9 gf} OF Max. RF Min. Operating characteristics *Stainless-steel lever In the case of V-15-1A5 7mm (reference value) 5mm In the case of V-15-1A5 OF Max. 3.53 N {360 gf} RF Min. 0.69 N {70 gf} Overtravel OT Min. Movement Differential MD Max. 2-M3x20 4.8 mm 1.5 mm 1.2 mm OF Max. 1.96 N {200 gf} RF Min. 0.29 N {30 gf} Operating characteristics Operating Force Releasing Force FP 10.30.15 2.8 Operating characteristics 6 A t=1* 16 mm 2 mm 5 mm Free Position FP Max. 45 mm Operating Position OP 209 mm Note. Not available for D2VW. 2-M3x20 OP OF Max. Overtravel OT Min. Movement Differential MD Max. R26 5.2 0.03 N {3 gf} Operating Force Releasing Force FP 10.30.15 2.8 Operating Force 6 t=1* 5.2 In the case of VX-5-1A2 Operating Position OP 18.61.6 mm Note. Pin plunger designed for models of OF 0.98 N {100 gf} or greater. Use in direction where the lever does not apply its own weight load to the plunger. 2-M3x16 22.20.15 27.8 Operating characteristics Pretravel PT Max. Overtravel OT Min. Movement Differential MD Max. 7.2 10.30.15 7.6 mm 3.6 mm 4.7 mm Operating Position OP Approx. 16.7 mm Note. This is designed for model of OF 0.25 N {25 gf}. Use in direction where the lever does not apply its own weight load to the plunger. 2-M3x16 22.20.1 0.34 N {35 gf} 0.04 N {4 gf} OF Max. RF Min. Pretravel PT Max. Overtravel OT Min. Movement Differential MD Max. 8 10.30.1 Operating Force Releasing Force Operating Position OP Approx. 10.6 mm Note. Pin plunger designed for models of OF 0.98 N {100 gf} or greater. Use in direction where the lever does not apply its own weight load to the plunger. 2-M3x16 22.20.1 27.8 In the case of V-15-1A5 Pretravel PT Max. Overtravel OT Min. Movement Differential MD Max. 20.2 2.8 Hinge Wire Lever VAV-5 7.1 10.30.1 OP Operating characteristics 5 mm (reference value) 4 mm Free Position FP Max. 30 mm Operating Position OP 204 mm Note. Not available for D2VW. Note1. Unless otherwise specified, a tolerance of 0.4mm applies to all dimensions. Note2. The operating characteristics are for operation in the A direction ( ). B-151 Basic Switch Common Accessories Long Hinge Lever VAV Basic Switch Common Accessories Reverse Hinge Modified Lever VAM-1 R7 t=1* A 5 15 20.3 Operating characteristics R46.5 Operating Force Releasing Force FP OP 5.2 Basic Switch Common Accessories 6 2.8 Reverse Roller Modified Lever VAM22 22.20.2 27.8 15 OF Max. 2.94 N {300 gf} RF Min. 0.39 N {40 gf} Overtravel OT Min. Movement Differential MD Max. 10.30.15 2-M3x20 *Stainless-steel lever A 9.5 dia.x4.8* Operating characteristics Operating Force Releasing Force R25 OP 5.2 5 FP 22.20.2 27.8 Free Position FP Max. 38 mm Operating Position OP 313 mm Note. Not available for D2VW. 2-M3x20 A 9.5 dia.x4.8* Operating characteristics 6 R51 Operating Force Releasing Force 15 FP OP 5.2 5 In the case of V-15-1A5 OF Max. 2.45 N {250 gf} RF Min. 0.39 N {40 gf} Overtravel OT Min. Movement Differential MD Max. 7 mm (reference value) 6 mm Free Position FP Max. 48 mm Operating Position OP 316 mm Note. Not available for D2VW. 10.30.15 2.8 3 mm (reference value) 4 mm *Stainless-steel roller Reverse Long Hinge Roller Lever VAM2 20.3 In the case of V-15-1A5 OF Max. 3.53 N {360 gf} RF Min. 0.69 N {70 gf} Overtravel OT Min. Movement Differential MD Max. 10.30.15 2.8 5 mm (reference value) 6 mm Free Position FP Max. 47 mm Operating Position OP 305 mm Note. Not available for D2VW. 6 20.3 In the case of V-15-1A5 22.20.15 27.8 2-M3x20 *Stainless-steel roller Note1. Unless otherwise specified, a tolerance of 0.4mm applies to all dimensions. Note2. The operating characteristics are for operation in the A direction ( ). * Application examples provided in this document are for reference only. In actual applications, confirm equipment functions and safety before using the product. * Consult your OMRON representative before using the product under conditions which are not described in the manual or applying the product to nuclear control systems, railroad systems, aviation systems, vehicles, combustion systems, medical equipment, amusement machines, safety equipment, and other systems or equipment that may have a serious influence on lives and property if used improperly. Make sure that the ratings and performance characteristics of the product provide a margin of safety for the system or equipment, and be sure to provide the system or equipment with double safety mechanisms. Note: Do not use this document to operate the Unit. OMRON Corporation ELECTRONIC AND MECHANICAL COMPONENTS COMPANY B-152 Contact: www.omron.com/ecb Cat. No. B118-E1-01 0812(0207)(O)