B-149
Basic Switch Common Accessories
Basic Switch Common Accessories
To ensure a secure insulation distance, or if there are other
metal parts or copper wire installed too close to the Switch, use
the Switch with insulation guard or use a separator purchased
separately to keep the insulation distance.
■List of models
Note. The Separator is made of EAVTC (epoxy alkyd/varnish tetron cloth) and has heat-resistant temperature of +130°C.
■Dimensions (Unit: mm)
Separator (Sold Separately)
Appearance Applicable Switches Thickness (mm) Model
V
D3V-01
VX
D2MV
D2RV
D2VW
0.18 SEPARATOR FOR V0.18
0.25 SEPARATOR FOR V0.25
SS
SS-P
D2S
D2SW
D2SW-P
0.18 SEPARATOR FOR SS0.18
0.4 SEPARATOR FOR SS0.4
Separator
Separator
14
3
24
22.2±0.1
10.3±0.1
2-3.2 dia. holes
11
38
8
SEPARATOR FOR V0.18
SEPARATOR FOR V0.25
9.5±0.1 7
7+0.23
−0.17
12+0.28
−0.12
2-2.6 dia. holes
21.6
SEPARATOR FOR SS0.18
SEPARATOR FOR SS0.4
B-150
Basic Switch Common Accessories
Basic Switch Common Accessories
Actuators are supplementary components used when operating
the Switch using cams or dogs or when transmitting mechanical
movements that are not in alignment with the switch plunger.
The VAL models are suitable for cases where a Switch is
operated by a rotary cam or sliding devices with relatively low
operation frequency.
The VAM models are designed to operate in reverse movements
and have high shock and vibration resistance. Since the
Overtravel (OT) of these models is rather large, they can be used
for automatic control or door switches of machining tools.
The VAV models can be used where a small Operating Force
(OF) is required.
These Actuators do not include Switches.
■Dimensions (Unit: mm) / Operating Characteristics
* Model numbers are for the Actuators only.
The value given for operating characteristics are reference values. For operating characteristics of models not listed above, consult your
OMRON sales representative.
Note1. Unless otherwise specified, a tolerance of ±0.4mm applies to all dimensions.
Note2. The operating characteristics are for operation in the A direction ( ).
Actuator (Sold Separately)
Note. Switches with the
mounting holes shown in
the diagram can be used
except for special
models.
22.2±0.15
10.3±0.15
●Leaf Spring Model
VAL
Note. Pin plunger (Designed for models of OF
1.96 N {200 gf} or greater).
Operating characteristics
In the case of
V-15-1A5
Operating Force OF Max.
Releasing Force RF Min.
2.26 N {230 gf}
0.49 N {50 gf}
Overtravel OT Min.
Movement Differential MD Max.
0.8 mm
0.4 mm
Free Position FP Max.
Operating Position OP
17 mm
14.9±0.5 mm
OP
FP
21.8
t=0.3, width 4.7*
10.3±0.15
22.2±0.15
2.8
27.8
5.1±0.1
18.2
5.6
*Stainless-steel lever
A
2-M3×16
●Simulated Leaf Spring
VAL12
Note. Pin plunger (Designed for models of OF
1.96 N {200 gf} or greater).
Operating characteristics
In the case of
V-15-1A5
Operating Force OF Max.
Releasing Force RF Min.
2.26 N {230 gf}
0.49 N {50 gf}
Overtravel OT Min.
Movement Differential MD Max.
0.8 mm
0.4 mm
Free Position FP Max.
Operating Position OP
22.9 mm
20.5±0.8 mm
OP
FP
20.6
t=0.3*
10.3±0.15
5.8
22.2±0.15
2.8
27.8
5.1
18.2
5.6
4.7
R2.4
*Stainless-steel lever
A
2-M3×16
●Roller Leaf Spring
VAL2
VAL02
Note. Pin plunger (Designed for models of OF
1.96 N {200 gf} or greater).
Operating characteristics
In the case of
V-15-1A5
Operating Force OF Max.
Releasing Force RF Min.
2.26 N {230 gf}
0.49 N {50 gf}
Overtravel OT Min.
Movement Differential MD Max.
0.8 mm
0.4 mm
Free Position FP Max.
Operating Position OP
22.6 mm
20.5±0.5 mm
OP
FP
20.6
10.3±0.05
22.2±0.08
2.8
27.8
5.1±0.25
18.2
5.6
4.8
4.8 dia.×4.8*
*
VAL2: polyacetal resin roller
VAL02: Stainless-steel roller
A
2-M3×16
B-151
Basic Switch Common Accessories
Basic Switch Common Accessories
Note1. Unless otherwise specified, a tolerance of ±0.4mm applies to all dimensions.
Note2. The operating characteristics are for operation in the A direction ( ).
●Long Hinge Lever
VAV
Note. Pin plunger designed for models of OF
0.98 N {100 gf} or greater.
Use in direction where the lever does
not apply its own weight load to the
plunger.
Operating characteristics
In the case of
V-15-1A5
Operating Force OF Max.
Releasing Force RF Min.
0.34 N {35 gf}
0.04 N {4 gf}
Pretravel PT Max.
Overtravel OT Min.
Movement Differential MD Max.
7.6 mm
3.6 mm
4.7 mm
Operating Position OP
Approx. 10.6 mm
OP
PT
15.1
R44.4
10.3±0.1
22.2±0.1
2.8
27.8
3.6
5.2 7.1
20.2
6
t=1, width 4.9*
*Stainless-steel lever
A
2-M3×16
●Hinge Wire Lever
VAV-5
Note. This is designed for model of OF 0.25 N
{25 gf}.
Use in direction where the lever does
not apply its own weight load to the
plunger.
Operating characteristics
In the case of
VX-5-1A2
Operating Force OF Max.
0.03 N {3 gf}
Pretravel PT Max.
Overtravel OT Min.
Movement Differential MD Max.
16 mm
2 mm
5 mm
Operating Position OP
Approx. 16.7 mm
●Hinge Roller Lever
VAV2
Note. Pin plunger designed for models of OF
0.98 N {100 gf} or greater.
Use in direction where the lever does
not apply its own weight load to the
plunger.
Operating characteristics
In the case of
V-15-1A5
Operating Force OF Max.
Releasing Force RF Min.
0.74 N {75 gf}
0.09 N {9 gf}
Pretravel PT Max.
Overtravel OT Min.
Movement Differential MD Max.
4.8 mm
1.5 mm
1.2 mm
Operating Position OP
18.6±1.6 mm
OP
PT
15.1
R19
10.3±0.15
22.2±0.15
2.8
27.8
3.6
5.2 7.2
20.3
6
4.8 dia.×4.8*
*polyacetal resin roller
A
2-M3×16
●Reverse Long Hinge Lever
VAM
Note. Not available for D2VW.
Operating characteristics
In the case of
V-15-1A5
Operating Force OF Max.
Releasing Force RF Min.
1.96 N {200 gf}
0.29 N {30 gf}
Overtravel OT Min.
Movement Differential MD Max.
7mm (reference value)
5mm
Free Position FP Max.
Operating Position OP
45 mm
20±9 mm
20.3
5.2
15
R62
10.3
±0.15
22.2
±0.15
2.8
27.8
OP FP
5
t=1*
*Stainless-steel lever
A
2-M3×20
6
●Reverse Hinge Lever
VAM21
Note. Not available for D2VW.
Operating characteristics
In the case of
V-15-1A5
Operating Force OF Max.
Releasing Force RF Min.
3.53 N {360 gf}
0.69 N {70 gf}
Overtravel OT Min.
Movement Differential MD Max.
5 mm (reference value)
4 mm
Free Position FP Max.
Operating Position OP
30 mm
20±4 mm
20.3
5.2
15
R26
10.3
±0.15
22.2
±0.15
2.8
27.8
OP FP
5
t=1*
*Stainless-steel lever
A
2-M3×20
6
B-152
Basic Switch Common Accessories
Basic Switch Common Accessories
Note1. Unless otherwise specified, a tolerance of ±0.4mm applies to all dimensions.
Note2. The operating characteristics are for operation in the A direction ( ).
●Reverse Hinge Modified Lever
VAM-1
Note. Not available for D2VW.
Operating characteristics
In the case of
V-15-1A5
Operating Force OF Max.
Releasing Force RF Min.
2.94 N {300 gf}
0.39 N {40 gf}
Overtravel OT Min.
Movement Differential MD Max.
5 mm (reference value)
6 mm
Free Position FP Max.
Operating Position OP
47 mm
30±5 mm
20.3
5.2
15 R46.5
10.3±0.15
22.2±0.2
2.8
27.8
OP FP
5
t=1*
R7
*Stainless-steel lever
A
2-M3×20
6
●Reverse Roller Modified Lever
VAM22
Note. Not available for D2VW.
Operating characteristics
In the case of
V-15-1A5
Operating Force OF Max.
Releasing Force RF Min.
3.53 N {360 gf}
0.69 N {70 gf}
Overtravel OT Min.
Movement Differential MD Max.
3 mm (reference value)
4 mm
Free Position FP Max.
Operating Position OP
38 mm
31±3 mm
20.3
5.2
15
R25
10.3±0.15
22.2±0.2
2.8
27.8
OP
2-M3×20
FP
6
5
9.5 dia.×4.8*
*Stainless-steel roller
A
●Reverse Long Hinge Roller Lever
VAM2
Note. Not available for D2VW.
Operating characteristics
In the case of
V-15-1A5
Operating Force OF Max.
Releasing Force RF Min.
2.45 N {250 gf}
0.39 N {40 gf}
Overtravel OT Min.
Movement Differential MD Max.
7 mm (reference value)
6 mm
Free Position FP Max.
Operating Position OP
48 mm
31±6 mm
20.3
5.2
15
R51
10.3±0.15
22.2±0.15
2.8
27.8
OP
2-M3×20
FP 5
9.5 dia.×4.8*
*Stainless-steel roller
A
6
• Application examples provided in this document are for reference only. In actual applications, confirm equipment functions and safety before using the product.
• Consult your OMRON representative before using the product under conditions which are not described in the manual or applying the product to nuclear control systems, railroad
systems, aviation systems, vehicles, combustion systems, medical equipment, amusement machines, safety equipment, and other systems or equipment that may have a serious
influence on lives and property if used improperly. Make sure that the ratings and performance characteristics of the product provide a margin of safety for the system or
equipment, and be sure to provide the system or equipment with double safety mechanisms.
OMRON Corporation
ELECTRONIC AND MECHANICAL COMPONENTS COMPANY Contact: www.omron.com/ecb Cat. No. B118-E1-01
0812(0207)(O)
Note: Do not use this document to operate the Unit.