- 426 - REV.1 Oct.-2003
EGP10A THRU EGP10K
1.0 AMP. Glass Passivated High Efficient Plastic Rectifiers
Voltage Range
50 to 800 Volts
Current
1.0 Ampere
F
eatures
Plastic material used carries Underwriters Laboratory
Classification 94V-0
Glass passivated cavity-free junction
Superfast recovery time for high efficiency
Low forward voltage, high current capability
Low leakage current
High surge current capability
High temperature soldering guaranteed:
300/10seconds, .375”(9.5mm) lead length at 5 lbs.,
(2.3kg) tension
M
echanical Data
Cases: JEDEC DO-
41 molded plastic over glass
body
Lead: Plated axial leads, solderable per MIL-STD-
750, Method 2026
Polarity: Color band denotes cathode end
Mounting position: Any
Weight: 0.012 ounce, 0.3 gram
DO-41
Dimensions in inches and (millimeters)
M
aximum Ratings and Electrical Characteristics
Rating at 25ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%
Type Number Symbol EGP
10A EGP
10B EGP
10D EGP
10F EGP
10G EGP
10J EGP
10K Units
Maximum Recurrent Peak Reverse Voltage VRRM 50 100 200 300 400 600 800 V
Maximum RMS Voltage VRMS 35 70 140 210 280 420 560 V
Maximum DC Blocking Voltage VDC 50 100 200 300 400 600 800 V
Maximum Average Forward Rectified
Current .375” (9.5mm) Lead Length
@TA=55
I(AV) 1.0 A
Peak Forward Surge Current, 8.3 ms Single
Half Sine-wave Superimposed on Rated
Load (JEDEC method ) IFSM 30.0 A
Maximum Instantaneous Forward Voltage
@1.0A VF0.95 1.25 1.7 V
Maximum DC Reverse Current @ TA=25
at Rated DC Blocking Voltage @ TA=125IR5.0
100.0 uA
uA
Maximum Reverse Recovery Time ( Note 1 )
TJ=25Trr 50 75 nS
Typical Junction Capacitance ( Note 2 ) Cj 22 15 pF
Typical Thermal Resistance (Note 3) RJA 50 /W
Operating Temperature Range TJ-65to+150
Storage Temperature Range TSTG -65to+150
Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A
2. Measured at 1.0 MHz and Applied Reverse Voltage of 4.0 Volts D.C.
3. Thermal Resistance from Junction toAmbient at 0.375” (9.5mm) Lead Length P.C.B.
Mounted.
- 427 -
FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM
50W
NONINDUCTIVE
1W
NON
INDUCTIVE
OSCILLOSCOPE
(NOTE 1)
PULSE
GENERATOR
(NOTE 2)
DUT
(+)
50Vdc
(approx)
(-)
NOTES: 1. Rise Time=7ns max. Input Impedance=
1 megohm 22pf
2. Rise Time=10ns max. Sourse Impedance=
50 ohms
(-)
(+)
10W
NONINDUCTIVE
-1.0A
-0.25A
0
+0.5A
trr
1cm SET TIME BASE FOR
5/ 10ns/ cm
FIG.3- MAXIMUM NON-REPETITIVE PEAK FORWARD
SURGE CURRENT
PEAK FORWARD SURGE CURRENT. (A)
110 100
25
30
15
0
5.0
20
10
NUMBER OF CYCLES AT 60Hz
Tj=Tj max.
8.3ms Single Half Sine Wave
JEDEC Method
RATINGS AND CHARACTERISTIC CURVES (EGP10A THRU EGP10K)
FIG.5- TYPICAL REVERSE CHARACTERISTICS
INSTANTANEOUS REVERSE CURRENT.( A)
020 40 60 80 100 120 140
10
100
1,000
1
0.1
0.01
PERCENT OF RATED PEAK REVERSE VOLTAGE. (%)
Tj=25 C
0
Tj=100 C
0
Tj=150 C
0
FIG.2- MAXIMUM FORWARD CURRENT DERATING
CURVE
AVERAGE FORWARD CURRENT. (A)
250 50 75 125 175150100
0
1.0
0.5
AMBIENT TEMPERATURE. ( C)
o
RESISTIVE OR
INDUCTIVE LOAD
0.375" (9.5mm) LEAD LENGTH
FIG.6- TYPICAL INSTANTANEOUS
FORWARD CHARACTERISTICS
INSTANTANEOUS FORWARD CURRENT. (A)
0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.80.2
0.01
1
10
50
0.1
FORWARD VOLTAGE. (V)
Tj=25 C
0
Tj=150 C
0
PULSE WIDTH-300 S
1% DUTY CYCLE
EGP10A-EGP10D
EGP10F EGP10K
FIG.4- TYPICAL JUNCTION CAPACITANCE
JUNCTION CAPACITANCE.(pF)
10.1 10 1,000
100
10
20
30
50
60
5
0
40
REVERSE VOLTAGE. (V)
Tj=25 C
f=1.0MHz
Vsig=50mVp-p
0
EGP10A-EGP10D
EGP10F & EGP10K
