1
LTC1545
Software-Selectable
Multiprotocol Transceiver
D2 D1
LTC1545
RTS
DTRDSR DCDCTS
D3
R2 R1
R3 D2
LTC1543
LLRITMRL TXDSCTETXC
RXCRXD
2
*OPTIONAL
1424111512179314192062322513 81018*21 25 7 16
1545 TA01
LTC1344A
D3
R2 R1R3 D1
TXD A (103)
TXD B
SCTE A (113)
SCTE B
RXC A (115)
RXC B
RXD A (104)
RXD B
RTS A (105)
RTS B
DTR A (108)
DTR B
CTS A (106)
SG (102)
SHIELD (101)
DB-25 CONNECTOR
TXC A (114)
TXC B
DCD A (109)
DCD B
DSR A (107)
DSR B
D4D5 R4
LL A (141)
RI A (125)
TM A (142)
RL A (140)
CTS B
R5
DTE or DCE Multiprotocol Serial Interface with DB-25 Connector
, LTC and LT are registered trademarks of Linear Technology Corporation.
Data Networking
CSU and DSU
Data Routers
Software-Selectable Transceiver Supports:
RS232, RS449, EIA530, EIA530-A, V.35, V.36, X.21
TUV/Detecon Inc. Certified NET1 and NET2
Compliant (Test Report No. NET2/071601/98)
TBR2 Compliant (Test Report No. CTR2/071601/98)
Software-Selectable Cable Termination Using
the LTC1344A
Complete DTE or DCE Port with LTC1543, LTC1344A
Operates from Single 5V Supply with LTC1543
The LTC
®
1545 is a 5-driver/5-receiver multiprotocol trans-
ceiver. The LTC1545 and LTC1543 form the core of a
complete software-selectable DTE or DCE interface port that
supports the RS232, RS449, EIA530, EIA530-A, V.35, V.36
or X.21 protocols. Cable termination may be implemented
using the LTC1344A software-selectable cable termination
chip or by using existing discrete designs.
The LTC1545 runs from a 5V supply and the charge pump on
the LTC1543. The part is available in a 36-lead SSOP surface
mount package.
FEATURES
DESCRIPTIO
U
APPLICATIO S
U
TYPICAL APPLICATIO
U
2
LTC1545
ABSOLUTE MAXIMUM RATINGS
W
WW
U
PACKAGE/ORDER INFORMATION
W
UU
ORDER PART
NUMBER
(Note 1)
Supply Voltage
V
CC
..................................................................... 6.5V
V
EE
........................................................10V to 0.3V
V
DD
.......................................................0.3V to 10V
Input Voltage
Transmitters ........................... 0.3V to (V
CC
+ 0.3V)
Receivers...............................................18V to 18V
Logic Pins .............................. 0.3V to (V
CC
+ 0.3V)
Output Voltage
Transmitters .................. (V
EE
– 0.3V) to (V
DD
+ 0.3V)
Receivers................................ 0.3V to (V
CC
+ 0.3V)
Short-Circuit Duration
Transmitter Output ..................................... Indefinite
Receiver Output.......................................... Indefinite
V
EE
.................................................................. 30 sec
Operating Temperature Range
LTC1545C .............................................. 0°C to 70°C
LTC1545I........................................... 40°C to 85°C
Storage Temperature Range ................ 65°C to 150°C
Lead Temperature (Soldering, 10 sec)................. 300°C
LTC1545CG
LTC1545IG
ELECTRICAL CHARACTERISTICS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
TOP VIEW
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
V
CC
V
DD
D1
D2
D3
R1
R2
R3
D4
R4
M0
M1
M2
DCE/DTE
D4ENB
R4EN
R5
D5
V
EE
GND
D1 A
D1 B
D2 A
D2 B
D3/R1 A
D3/R1 B
R2 A
R2 B
R3 A
R3 B
D4 A
R4 A
R5 A
D5 A
V
DD
V
CC
R1
D2
D1
D3
R3
G PACKAGE
36-LEAD PLASTIC SSOP
D5
R5
D4
R2
R4
T
JMAX
= 150°C, θ
JA
= 65°C/ W
Consult factory for Military grade parts.
The denotes specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C.
VCC = 5V, VDD = 8V, VEE = – 7V for V.28, – 5.5V for V.10, V.11 (Notes 2, 3)
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
Supplies
I
CC
V
CC
Supply Current (DCE Mode, RS530, RS530-A, X.21 Modes, No Load 2.7 5 mA
All Digital Pins = GND or V
CC
) RS530, RS530-A, X.21 Modes, Full Load 110 150 mA
V.28 Mode, No Load 13 mA
V.28 Mode, Full Load 13 mA
No-Cable Mode, D4ENB = HIGH 10 500 µA
I
EE
V
EE
Supply Current (DCE Mode, RS530, RS530-A, X.21 Modes, No Load 2.0 4.0 mA
All Digital Pins = GND or V
CC
) RS530, X.21 Modes, Full Load 23 35 mA
RS530-A, Full Load 34 50 mA
V.28 Mode, No Load 13 mA
V.28 Mode, Full Load 12 18 mA
No-Cable Mode, D4ENB = HIGH 10 500 µA
I
DD
V
DD
Supply Current (DCE Mode, RS530, RS530-A, X.21 Modes, NoLoad 0.3 2 mA
All Digital Pins = GND or V
CC
) RS530, RS530-A, X.21 Modes, Full Load 0.3 2 mA
V.28 Mode, No Load 13 mA
V.28 Mode, Full Load 13.5 18 mA
No-Cable Mode, D4ENB = HIGH 10 500 µA
P
D
Internal Power Dissipation (DCE Mode, RS530, RS530-A, X.21 Modes, Full Load 340 mW
(All Digital Pins = GND or V
CC
) V.28 Mode, Full Load 64 mW
3
LTC1545
ELECTRICAL CHARACTERISTICS
The denotes specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C.
VCC = 5V, VDD = 8V, VEE = – 7V for V.28, – 5.5V for V.10, V.11 (Notes 2, 3)
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
Logic Inputs and Outputs
V
IH
Logic Input High Voltage 2V
V
IL
Logic Input Low Voltage 0.8 V
I
IN
Logic Input Current D1, D2, D3, D4, D5 ±10 µA
M0, M1, M2, DCE, D4ENB, R4EN = GND (LTC1545C) 100 50 30 µA
M0, M1, M2, DCE, D4ENB, R4EN = GND (LTC1545I) 120 50 30 µA
M0, M1, M2, DCE, D4ENB, R4EN = V
CC
±10 µA
V
OH
Output High Voltage I
O
= –4mA 3 4.5 V
V
OL
Output Low Voltage I
O
= 4mA 0.3 0.8 V
I
OSR
Output Short-Circuit Current 0V V
O
V
CC
–50 40 50 mA
I
OZR
Three-State Output Current M0 = M1 = M2 = V
CC
, 0V V
O
V
CC
±1µA
V.11 Driver
V
ODO
Open Circuit Differential Output Voltage R
L
= 1.95k (Figure 1) ±5V
V
ODL
Loaded Differential Output Voltage R
L
= 50 (Figure 1) 0.5V
ODO
0.67V
ODO
R
L
= 50 (Figure 1) ±2V
V
OD
Change in Magnitude of Differential R
L
= 50 (Figure 1) 0.2 V
Output Voltage
V
OC
Common Mode Output Voltage R
L
= 50 (Figure 1) 3V
V
OC
Change in Magnitude of Common Mode R
L
= 50 (Figure 1) 0.2 V
Output Voltage
I
SS
Short-Circuit Current V
OUT
= GND ±150 mA
I
OZ
Output Leakage Current 0.25V V
O
0.25V, Power Off or ±1±100 µA
No-Cable Mode or Driver Disabled
t
r
, t
f
Rise or Fall Time LTC1545C (Figures 2, 5) 21525 ns
LTC1545I (Figures 2, 5) 21535 ns
t
PLH
Input to Output LTC1545C (Figures 2, 5) 20 40 65 ns
LTC1545I (Figures 2, 5) 20 40 75 ns
t
PHL
Input to Output LTC1545C (Figures 2, 5) 20 40 65 ns
LTC1545I (Figures 2, 5) 20 40 75 ns
t Input to Output Difference, t
PLH
– t
PHL
LTC1545C (Figures 2, 5) 0312 ns
LTC1545I (Figures 2, 5) 0317 ns
t
SKEW
Output to Output Skew (Figures 2, 5) 3 ns
V.11 Receiver
V
TH
Input Threshold Voltage 7V V
CM
7V 0.2 0.2 V
V
TH
Input Hysteresis 7V V
CM
7V 15 40 mV
I
IN
Input Current (A, B) 10V V
A,B
10V ±0.66 mA
R
IN
Input Impedance 10V V
A,B
10V 15 30 k
t
r
, t
f
Rise or Fall Time (Figures 2, 6) 15 ns
t
PLH
Input to Output LTC1545C (Figures 2, 6) 50 80 ns
LTC1545I (Figures 2, 6) 50 90 ns
t
PHL
Input to Output LTC1545C (Figures 2, 6) 50 80 ns
LTC1545I (Figures 2, 6) 50 90 ns
t Input to Output Difference, t
PLH
– t
PHL
LTC1545C (Figures 2, 6) 0416 ns
LTC1545I (Figures 2, 6) 0421 ns
4
LTC1545
ELECTRICAL CHARACTERISTICS
Note 1: Absolute Maximum Ratings are those values beyond which the life
of a device may be impaired.
Note 2: All currents into device pins are positive; all currents out of device
are negative. All voltages are referenced to device ground unless otherwise
specified.
Note 3: All typicals are given for V
CC
= 5V, V
DD
= 8V, V
EE
= –7V for V.28,
5.5V for V.10, V.11 and T
A
= 25°C.
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
V.10 Driver
V
O
Output Voltage Open Circuit, R
L
= 3.9k ±4±6V
V
T
Output Voltage R
L
= 450 (Figure 3) ±3.6 V
R
L
= 450 (Figure 3) 0.9V
O
I
SS
Short-Circuit Current V
O
= GND ±150 mA
I
OZ
Output Leakage Current 0.25V V
O
0.25V, Power Off or ±0.1 ±100 µA
No-Cable Mode or Driver Disabled
t
r
, t
f
Rise or Fall Time R
L
= 450, C
L
= 100pF (Figures 3, 7) 2 µs
t
PLH
Input to Output R
L
= 450, C
L
= 100pF (Figures 3, 7) 1 µs
t
PHL
Input to Output R
L
= 450, C
L
= 100pF (Figures 3, 7) 1 µs
V.10 Receiver
V
TH
Receiver Input Threshold Voltage 0.25 0.25 V
V
TH
Receiver Input Hysteresis 25 50 mV
I
IN
Receiver Input Current 10V V
A
10V ±0.66 mA
R
IN
Receiver Input Impedance 10V V
A
10V 15 30 k
t
r
, t
f
Rise or Fall Time (Figures 4, 8) 15 ns
t
PLH
Input to Output (Figures 4, 8) 55 ns
t
PHL
Input to Output (Figures 4, 8) 109 ns
t Input to Output Difference, t
PLH
– t
PHL
(Figures 4, 8) 60 ns
V.28 Driver
V
O
Output Voltage Open Circuit ±10 V
R
L
= 3k (Figure 3) ±5±8.5 V
I
SS
Short-Circuit Current V
O
= GND ±150 mA
I
OZ
Output Leakage Current 0.25V V
O
0.25V, Power Off or ±1±100 µA
No-Cable Mode or Driver Disabled
SR Slew Rate R
L
= 3k, C
L
= 2500pF (Figures 3, 7) 430V/µs
t
PLH
Input to Output R
L
= 3k, C
L
= 2500pF (Figures 3, 7) 1.3 2.5 µs
t
PHL
Input to Output R
L
= 3k, C
L
= 2500pF (Figures 3, 7) 1.3 2.5 µs
V.28 Receiver
V
THL
Input Low Threshold Voltage 1.5 0.8 V
V
TLH
Input High Threshold Voltage 2 1.6 V
V
TH
Receiver Input Hysterisis 0.1 0.3 V
R
IN
Receiver Input Impedance 15V V
A
15V 357 k
t
r
, t
f
Rise or Fall Time (Figures 4, 8) 15 ns
t
PLH
Input to Output (Figures 4, 8) 60 100 ns
t
PHL
Input to Output (Figures 4, 8) 150 450 ns
The denotes specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C.
VCC = 5V, VDD = 8V, VEE = – 7V for V.28, – 5.5V for V.10, V.11 (Notes 2, 3)
5
LTC1545
V
CC
(Pins 1, 19): Positive Supply for the Transceivers.
4.75V V
CC
5.25V. Connect a 1µF capacitor to ground.
V
DD
(Pins 2, 20): Positive Supply Voltage for V.28. Con-
nect to V
DD
Pin 3 on LTC1543 or 8V supply. Connect a 1µF
capacitor to ground.
D1 (Pin 3): TTL Level Driver 1 Input.
D2 (Pin 4): TTL Level Driver 2 Input.
D3 (Pin 5): TTL Level Driver 3 Input.
R1 (Pin 6): CMOS Level Receiver 1 Output.
R2 (Pin 7): CMOS Level Receiver 2 Output.
R3 (Pin 8): CMOS Level Receiver 3 Output.
D4 (Pin 9): TTL Level Driver 4 Input.
R4 (Pin 10): CMOS Level Receiver 4 Output.
M0 (Pin 11): TTL Level Mode Select Input 0 with Pull-Up
to V
CC
.
M1 (Pin 12): TTL Level Mode Select Input 1 with Pull-Up
to V
CC
.
M2 (Pin 13): TTL Level Mode Select Input 2 with Pull-Up
to V
CC
.
DCE/DTE (Pin 14): TTL Level Mode Select Input with
Pull-Up to V
CC
. Logic high enables Driver 3. Logic low
enables Receiver 1.
D4ENB (Pin 15): TTL Level Enable Input with Pull-Up to
V
CC
. Logic low enables Driver 4.
R4EN (Pin 16): TTL Level Enable Input with Pull-Up to V
CC
.
Logic high enables Receiver 4.
PIN FUNCTIONS
UUU
R5 (Pin 17): CMOS Level Receiver 5 Output.
D5 (Pin 18): TTL Level Driver 5 Input.
D5 A (Pin 21): Driver 5 Output.
R5 A (Pin 22): Receiver 5 Input.
R4 A (Pin 23): Receiver 4 Input.
D4 A (Pin 24): Driver 4 Input.
R3 B (Pin 25): Receiver 3 Noninverting Input.
R3 A (Pin 26): Receiver 3 Inverting Input.
R2 B (Pin 27): Receiver 2 Noninverting Input.
R2 A (Pin 28): Receiver 2 Inverting Input.
D3/R1 B (Pin 29): Receiver 1 Noninverting Input and
Driver 3 Noninverting Output.
D3/R1 A (Pin 30): Receiver 1 Inverting Input and Driver 3
Inverting Output.
D2 B (Pin 31): Driver 2 Noninverting Output.
D2 A (Pin 32): Driver 2 Inverting Output.
D1 B (Pin 33): Driver 1 Noninverting Output.
D1 A (Pin 34): Driver 1 Inverting Output.
GND (Pin 35): Ground.
V
EE
(Pin 36): Negative Supply Voltage. Connect to V
EE
Pin
26 on LTC1543. Connect a 1µF capacitor to ground.
Figure 1. V.11 Driver Test Circuit Figure 2. V.11 Driver/Receiver AC Test Circuit
A
B
1545 F01
V
OD
V
OC
R
L
R
L
A
B
A
R
B
1545 F02
R
L
100
C
L
100pF
C
L
100pF 15pF
TEST CIRCUITS
6
LTC1545
TEST CIRCUITS
Figure 3. V.10/V.28 Driver Test Circuit
A
D
1545 F03
R
L
C
L
A
D
1545 F04
15pF
R
A
Figure 4. V.10/V.28 Receiver Test Circuit
(Note 1) (Note 2) (Note 1) (Note 3)
LTC1545 MODE NAME M2 M1 M0 D1 D2 D3 D4 D5 R1 R2 R3 R4 R5
Not Used (Default V.11) 0 0 0 V.11 V.11 V.11 V.10 V.10 V.11 V.11 V.11 V.10 V.10
RS530A 0 0 1 V.11 V.10 V.11 V.10 V.10 V.11 V.10 V.11 V.10 V.10
RS530 0 1 0 V.11 V.11 V.11 V.10 V.10 V.11 V.11 V.11 V.10 V.10
X.21 0 1 1 V.11 V.11 V.11 V.10 V.10 V.11 V.11 V.11 V.10 V.10
V.35 1 0 0 V.28 V.28 V.28 V.28 V.28 V.28 V.28 V.28 V.28 V.28
RS449/V.36 1 0 1 V.11 V.11 V.11 V.10 V.10 V.11 V.11 V.11 V.10 V.10
V.28/RS232 1 1 0 V.28 V.28 V.28 V.28 V.28 V.28 V.28 V.28 V.28 V.28
D4ENB = 1, R4EN = 0 111ZZZZZZZZZZ
M0 = M1 = M2 = 1
ODE SELECTIO
WU
Note 1: Driver 3 and Receiver 1 are enabled (and disabled) by
DCE/DTE (Pin 14). Logic high enables Driver 3. Logic low enables
Receiver 1.
Note 2: Driver 4 is enabled by D4ENB = 0 (Pin 15).
Note 3: Receiver 4 is enabled by R4EN = 1 (Pin 16).
SWITCHI G TI E WAVEFOR S
UWW
Figure 5. V.11 Driver Propagation Delays
5V 1.5V 1.5V
50% 10%
90%
t
PLH
t
r
0V
V
O
V
O
–V
O
D
B – A
A
B
t
PHL
t
SKEW
t
SKEW
1545 F05
1/2 V
O
f = 1MHz : t
r
10ns : t
f
10ns
V
DIFF
= V(B) – V(A) 50% 10%
90%
t
f
7
LTC1545
SWITCHI G TI E WAVEFOR S
UWW
Figure 6. V.11 Receiver Propagation Delays
APPLICATIONS INFORMATION
WUUU
Overview
The LTC1543/LTC1545 form the core of a complete soft-
ware-selectable DTE or DCE interface port that supports
the RS232, RS449, EIA530, EIA530-A, V.35, V.36 or X.21
protocols. Cable termination may be implemented using
the LTC1344A software-selectable cable termination chip
or by using existing discrete designs.
A complete DCE-to-DTE interface operating in EIA530
mode is shown in Figure 9. The LTC1543 of each port is
used to generate the clock and data signals. The LTC1545
is used to generate the control signals along with LL (Local
Loop-Back), RL (Remote Loop-Back), TM (Test Mode)
and RI (Ring Indicate). The LTC1344A cable termination
chip is used only for the clock and data signals because
they must support V.35 cable termination. The control
signals do not need any external resistors.
Mode Selection
The interface protocol is selected using the mode select
pins M0, M1 and M2 (see the Mode Selection table).
For example, if the port is configured as a V.35 interface,
the mode selection pins should be M2 = 1, M1 = 0, M0 = 0.
For the control signals, the drivers and receivers will
operate in V.28 (RS232) electrical mode. For the clock and
data signals, the drivers and receivers will operate in V.35
electrical mode. The DCE/DTE pin will configure the port
for DCE mode when high, and DTE when low.
The interface protocol may be selected simply by plugging
the appropriate interface cable into the connector. The
mode pins are routed to the connector and are left uncon-
nected (1) or wired to ground (0) in the cable as shown in
Figure 10.
VIH
VIL
1.5V
1.5V
1.5V
1.5V
tPHL
VOH
VOL
A
R
tPLH
1545 F08
Figure 8. V.10, V.28 Receiver Propagation Delays
3V
0V
1.5V
0V
–3V
3V
1.5V
0V
3V
–3V
t
PHL
t
f
V
O
–V
O
D
A
t
PLH
t
r
1545 F07
Figure 7. V.10, V.28 Driver Propagation Delays
VOD2
–VOD2
0V
1.5V
0V
1.5V
tPLH
VOH
VOL
B – A
R
tPHL
1545 F06
f = 1MHz : tr 10ns : tf 10ns INPUT
OUTPUT
8
LTC1545
APPLICATIONS INFORMATION
WUUU
LTC1543
DCEDTE
LTC1543
LTC1344A LTC1344A
1545 F09
D3
D3
R1 103
103
103
R3
LTC1545
D3
D4
D2
R1
R2
R3
LL
TM
RI
RL
TXC
RXC
RXD
TXD
SCTE
TXC
RXC
RXD
SERIAL
CONTROLLER
D2 103
SCTE R2
D1 103
TXD R3
R1
D2
D1
LTC1545
R2
R1
R3
D2
D1
D4
D5
TXD
SCTE
TXC
RXC
RXD
RTS
DTR
DCD
DSR
CTS
LL
TM
RTS
DTR
DCD
DSR
CTS
RTS
DTR
DCD
DSR
CTS
LL
TM
RI
RL
RI
RL
SERIAL
CONTROLLER
R2
R4
D3
R4
R5
D5
R5
D1
The mode selection may also be accomplished by using
jumpers to connect the mode pins to ground or V
CC
.
Cable Termination
Traditional implementations have included switching
resistors with expensive relays, or required the user to
change termination modules every time the interface
standard has changed. Custom cables have been used
The internal pull-up current sources will ensure a binary 1
when a pin is left unconnected and that the LTC1543/
LTC1545 and the LTC1344A enter the no-cable mode
when the cable is removed. In the no-cable mode the
LTC1543/LTC1545 supply current drops to less than
200µA and all LTC1543/LTC1545 driver outputs and
LTC1344A resistive terminations are forced into a high
impedance state.
Figure 9. Complete Multiprotocol Interface in EIA530 Mode
9
LTC1545
APPLICATIONS INFORMATION
WUUU
Figure 10: Single Port DCE V.35 Mode Selection in the Cable
NC
NC
VCC CABLE
10k
1545 F10
11
12
13
14
LTC1543
LTC1545
CONNECTOR
14
13
12
11
15
16
22
21
M2 M1
LTC1344A
LATCH
M0 (DATA)
23 24 1
(DATA)
M0
M1
M2
DCE/DTE
DCE/DTE
M2
M1
M0
D4ENB
R4EN
(DATA)
DCE/
DTE
The V.10 receiver configuration in the LTC1545 is shown
in Figure 13. In V.10 mode switch S3 inside the LTC1545
is turned off. The noninverting input is disconnected
inside the LTC1545 receiver and connected to ground.The
cable termination is then the 30k input impedance to
ground of the LTC1545 V.10 receiver.
V.11 (RS422) Interface
A typical V.11 balanced interface is shown in Figure 14. A
V.11 differential generator with outputs A and B with
ground C is connected to a differential receiver with
ground C', inputs A' connected to A, B' connected to B. The
V.11 interface has a differential termination at the receiver
end that has a minimum value of 100. The termination
resistor is optional in the V.11 specification, but for the
high speed clock and data lines, the termination is required
to prevent reflections from corrupting the data. The
receiver inputs must also be compliant with the imped-
ance curve shown in Figure 12.
with the termination in the cable head or separate termina-
tions are built on the board and a custom cable routes the
signals to the appropriate termination. Switching the
terminations with FETs is difficult because the FETs must
remain off even though the signal voltage is beyond the
supply voltage for the FET drivers or the power is off.
Using the LTC1344A along with the LTC1543/LTC1545
solves the cable termination switching problem. Via soft-
ware control, the LTC1344A provides termination for the
V.10 (RS423), V.11 (RS422), V.28 (RS232) and V.35
electrical protocols.
V.10 (RS423) Interface
A typical V.10 unbalanced interface is shown in Figure 11.
A V.10 single-ended generator output A with ground C is
connected to a differential receiver with inputs A' con-
nected to A, and input C' connected to the signal return
ground C. Usually, no cable termination is required for
V.10 interfaces, but the receiver inputs must be compliant
with the impedance curve shown in Figure 12.
10
LTC1545
APPLICATIONS INFORMATION
WUUU
Figure 12. V.10 Receiver Input Impedance
Figure 13. V.10 Receiver Configuration
Figure 14. Typical V.11 Interface
R3
124
R5
20k
LTC1344A
LTC1543
LTC1545
RECEIVER
1545 F15
A
B
A
'
B
'
C
'
R1
51.5R8
6k
S2 S3
R2
51.5
R6
10k
R7
10k
GND
R4
20k
S1
I
Z
V
Z
10V
–3.25mA
3.25mA
–3V
3V 10V
1545 F12
R5
20k
LTC1545
RECEIVER
1545 F13
A
B
A
'
B
'
C
'
R8
6k
S3
R6
10k
R7
10k
GND
R4
20k
AA'
B
C
B'
C'
GENERATOR
BALANCED
INTERCONNECTING
CABLE LOAD
CABLE
TERMINATION RECEIVER
100
MIN
1545 F14
AA
'
CC
'
GENERATOR
BALANCED
INTERCONNECTING
CABLE LOAD
CABLE
TERMINATION RECEIVER
1545 F11
Figure 11. Typical V.10 Interface
Figure 15. V.11 Receiver Configuration
In V.11 mode, all switches are off except S1 inside the
LTC1344A which connects a 103 differential termina-
tion impedance to the cable as shown in Figure 15.
V.28 (RS232) Interface
A typical V.28 unbalanced interface is shown in Figure 16.
A V.28 single-ended generator output A with ground C is
connected to a single-ended receiver with input A' con-
nected to A, ground C' connected via the signal return
ground C.
In V.28 mode, all switches are off except S3 inside the
LTC1543/LTC1545 which connects a 6k (R8) impedance
to ground in parallel with 20k (R5) plus 10k (R6) for a
combined impedance of 5k as shown in Figure 17. The
noninverting input is disconnected inside the LTC1543/
LTC1545 receiver and connected to a TTL level reference
voltage for a 1.4V receiver trip point.
11
LTC1545
APPLICATIONS INFORMATION
WUUU
Figure 16. Typical V.28 Interface
AA
'
CC
'
GENERATOR
BALANCED
INTERCONNECTING
CABLE LOAD
CABLE
TERMINATION RECEIVER
1545 F16
V.35 interface requires a T or delta network termination at
the receiver end and the generator end. The receiver
differential impedance measured at the connector must be
100±10, and the impedance between shorted termi-
nals (A' and B') and ground C' must be 150 ±15.
In V.35 mode, both switches S1 and S2 inside the LTC1344A
are on, connecting the T network impedance as shown in
Figure 19. Both switches in the LTC1543 are off. The 30k
input impedance of the receiver is placed in parallel with
the T network termination, but does not affect the overall
input impedance significantly.
The generator differential impedance must be 50 to
150 and the impedance between shorted terminals (A
and B) and ground C must be 150 ±15. For the
generator termination, switches S1 and S2 are both on and
the top side of the center resistor is brought out to a pin so
it can be bypassed with an external capacitor to reduce
common mode noise as shown in Figure 20.
Figure 20. V.35 Driver Using the LTC1344A
V.35 DRIVER
A
B
C
51.5
S2
ON
S1
ON
1545 F20
51.5
LTC1344A
124
C1
100pF
R3
124
R5
20k
LTC1344A
LTC1543
RECEIVER
1545 F19
A
B
A
'
B
'
C
'
R1
51.5R8
6k
S2
S3
R2
51.5
R6
10k
R7
10k
GND
R4
20k
S1
Figure 19. V.35 Receiver Configuration
V.35 Interface
A typical V.35 balanced interface is shown in Figure 18. A
V.35 differential generator with outputs A and B with
ground C is connected to a differential receiver with
ground C', inputs A' connected to A, B' connected to B. The
Figure 18. Typical V.35 Interface
AA
'
B
C
B
'
C
'
GENERATOR
BALANCED
INTERCONNECTING
CABLE LOAD
CABLE
TERMINATION RECEIVER
1545 F18
50125
50
50
125
50
Figure 17. V.28 Receiver Configuration
R3
124
R5
20k
LTC1344A
LTC1543
LTC1545
RECEIVER
1545 F17
A
B
A
'
B
'
C
'
R1
51.5R8
6k
S2
S3
R2
51.5
R6
10k
R7
10k
GND
R4
20k
S1
12
LTC1545
APPLICATIONS INFORMATION
WUUU
DTE vs DCE Operation
The DCE/DTE pin acts as an enable for Driver 3/Receiver
1 in the LTC1543, and Driver 3/Receiver 1 in the LTC1545.
The LTC1543/LTC1545 can be configured for either DTE
or DCE operation in one of two ways: a dedicated DTE or
DCE port with a connector of appropriate gender, or a port
with one connector that can be configured for DTE or DCE
operation by rerouting the signals to the LTC1543/LTC1545
using a dedicated DTE cable or dedicated DCE cable.
A dedicated DTE port using a DB-25 male connector is
shown in Figure 22. The interface mode is selected by logic
outputs from the controller or from jumpers to either V
CC
or GND on the mode select pins. A dedicated DCE port
using a DB-25 female connector is shown in Figure 23.
A port with one DB-25 connector, can be configured for
either DTE or DCE operation is shown in Figure 24. The
configuration requires separate cables for proper signal
routing in DTE or DCE operation. For example, in DTE
mode, the TXD signal is routed to Pins 2 and 14 via Driver
1 in the LTC1543. In DCE mode, Driver 1 now routes the
RXD signal to Pins 2 and 14.
Compliance Testing
A European standard EN 45001 test report is available for
the LTC1343/LTC1545/LTC1344A chipset. A copy of the
test report is available from LTC or TUV Telecom Services
Inc. (formerly Detecon Inc.)
The title of the report is:
Test Report No. NET2/071601/98.
The address of TUV Telecom Services Inc. is:
TUV Telecom Services Inc.
Suite 107
1775 Old Highway 8
St. Paul, MN 55112 USA
Tel. +1 (612) 639-0775
Fax. +1 (612) 639-0873
Any mismatch in the driver rise and fall times or skew in
the driver propagation delays will force current through
the center termination resistor to ground, causing a high
frequency common mode spike on the A and B terminals.
The common mode spike can cause EMI problems that are
reduced by capacitor C1 which shunts much of the com-
mon mode energy to ground rather than down the cable.
No-Cable Mode
The no-cable mode (M0 = M1 = M2 = D4ENB = 1, R4EN = 0)
is intended for the case when the cable is disconnected
from the connector. The charge pump, bias circuitry,
drivers and receivers are turned off, the driver outputs are
forced into a high impedance state, and the supply current
drops to less than 200µA.
Charge Pump
The LTC1543 uses an internal capacitive charge pump to
generate V
DD
and V
EE
as shown in Figure 21. A voltage
doubler generates about 8V on V
DD
and a voltage inverter
generates about –7.5V for V
EE
. Four 1µF surface mounted
tantalum or ceramic capacitors are required for C1, C2, C3
and C4. The V
EE
capacitor C5 should be a minimum of
3.3µF. All capacitors are 16V and should be placed as close
as possible to the LTC1543 to reduce EMI. The turn-on
time for the charge pump is 60ms.
28
27
26
25
1545 F21
3
2
1
4
C3
1µF
C4
1µF
5V
C1
1µF
C2
1µF
C5
3.3µF
LTC1543
V
DD
C1
+
C1
V
CC
C2
+
C2
V
EE
GND
+
Figure 21. Charge Pump
Receiver Fail-Safe
All LTC1543/LTC1545 receivers feature fail-safe opera-
tion in all modes. If the receiver inputs are left floating or
shorted together by a termination resistor, the receiver
output will always be forced to a logic high.
13
LTC1545
Figure 22. Controller-Selectable Multiprotocol DTE Port with DB-25 Connector
10
17
18
D2
D1
LTC1545
RTS
DTR
DSR
DCD
CTS
D3
R2
R1
R3
D2
LTC1543
LL
RI
TM
TXD
SCTE
TXC
RXC
RXD
M0
M1
M2
DCE/DTE
V
CC
V
DD
V
CC
5V
V
EE
GND
2
21
14
24
11
15
12
17
9
3
1
4
19
20
8
23
10
6
22
5
13
18
25
*
*OPTIONAL
21
7
16
1544 F22
D3
R2
R1
R3
D1
C2
1µF
C1
1µF
C5
1µF
C3
1µF
C4
3.3µF
TXD A (103)
TXD B
SCTE A (113)
SCTE B
RXC A (115)
RXC B
RXD A (104)
RXD B
RTS A (105)
RTS B
DTR A (108)
DTR B
CTS A (106)
CTS B
SG
SHIELD
DB-25 MALE
CONNECTOR
TXC A (114)
TXC B
DCD A (109)
DCD B
DSR A (107)
DSR B
D4
16109764
3 8 11 12 13
5
2
15 18 17 19 20 22
LTC1344A
LATCH
C6
100pF C7
100pF C8
100pF
V
CC
V
CC
5V
23 24
14
1
DCE/DTE
M2
M1
M0
CHARGE
PUMP
+
28
3
1
2
4
5
6
7
8
9
10
11
12
13
14
1,19
2,20
3
4
5
6
7
8
9
R4EN
D4ENB 15
16
24
23
22
25
26
27
28
29
30
31
32
33
NC
27
26
25
24
23
22
21
20
19
18
17
16
15
34
35
36
V
EE
M0
M1
M2
DCE/DTE
M0
M1
M2
11
12
13
14
C12
1µF
C13
1µF
C11
1µF
C10
1µFC9
1µF
RL D5 21
R4
R5
LL (141)
RI (125)
TM (142)
RL (140)
TYPICAL APPLICATIONS
U
14
LTC1545
TYPICAL APPLICATIONS
U
10
17
18
D2
D1
LTC1545
D3
R2
R1
R3
V
CC
V
DD
V
EE
GND
D4
1,19
2,20
3
4
5
6
7
8
9
R4EN
D4ENB 15
16
24
23
22
25
26
27
28
29
30
31
32
33
34
35
36
M0
M1
M2
DCE/DTE
11
12
13
14
D5 21
R4
R5
D2
LTC1543
RXD
RXC
TXC
SCTE
TXD
CTS
DSR
DCD
DTR
RI
LL
RTS
RL
TM
M0
M1
M2
DCE/DTE
V
CC
5V
NC
NC
3
16
17
9
15
12
24
11
2
1
5
13
6
8
22
10
20
23
4
19
7
14
1544 F23
D3
R2
R1
R3
D1
C2
1µF
C1
1µF
C5
1µF
C3
1µF
C4
3.3µF
16109764
3 8 11 12 13
5
2
15 18 17 19 20 22
LTC1344A
C6
100pF C7
100pF C8
100pF
V
CC
V
CC
V
CC
5V
23 24
14
1
DCE/DTE
M2
M1
M0
CHARGE
PUMP
+
28
3
1
2
4
5
6
7
8
9
10
NC
11
12
13
14
27
26
25
24
23
22
21
20
19
18
17
16
15
V
EE
M0
M1
M2
21
LATCH
C12
1µF
C13
1µF
C11
1µF
C10
1µF
C9
1µF
RXD A (104)
RXD B
RXC A (115)
RXC B
SCTE A (113)
SCTE B
TXD A (103)
TXD B
TXC A (114)
TXC B
SGND (102)
SHIELD (101)
DB-25 FEMALE
CONNECTOR
CTS A (106)
CTS B
DSR A (107)
DSR B
RTS A (105)
RTS B
DCD A (109)
DCD B
DTR A (108)
DTR B
18
*
*OPTIONAL
21
25
LL (141)
RL (140)
TM (142)
RI (125)
Figure 23. Controller-Selectable DCE Port with DB-25 Connector
15
LTC1545
TYPICAL APPLICATIONS
U
Figure 24. Controller-Selectable Multiprotocol DTE/DCE Port with DB-25 Connector
10
17
18
D2
D1
LTC1545
D3
R2
R1
R3
VCC
VDD
VEE
GND
D4
1,19
2,20
3
4
5
6
7
8
9
R4EN
D4ENB 15
16 NC
24
23
22
25
26
27
28
29
30
31
32
33
34
35
36
M0
M1
M2
DCE/DTE
11
12
13
14
D5 21
R4
R5
18
*
*OPTIONAL
21
25
LL
LL
RL
RLTM
TM
RI
RI
D2
LTC1543
DTE_TXD/DCE_RXD
DTE_TXC/DCE_TXC
DTE_RXC/DCE_SCTE
DTE_RXD/DCE_TXD
DTE_RTS/DCE_CTS
DTE_DTR/DCE_DSR
DTE_DCD/DCE_DCD
DTE_DSR/DCE_DTR
DTE_CTS/DCE_RTS
DTE_LL/DCE_RI
DTE_RI/DCE_LL
DTE_TM/DCE_RL
DTE_RL/DCE_TM
DTE_SCTE/DCE_RXC
M0
M1
M2
DCE/DTE
VCC
5V
2
14
24
11
15
12
17
9
3
1
4
19
20
8
23
10
6
22
5
13
7
16
1544 F24
D3
R2
R1
R3
D1
C2
1µF
C1
1µF
C5
1µF
C3
1µF
C4
3.3µF
TXD A
TXD B
SCTE A
SCTE B
RXD A
RXD B
RXC A
RXC B
RXC A
RXC B
RXD A
RXD B
RTS A
RTS B
DTR A
DTR B
CTS A
CTS B
DSR A
DSR B
CTS A
CTS B
SG
SHIELD
DB-25
CONNECTOR
TXC A
TXC B
SCTE A
SCTE B
TXD A
TXD B
TXC A
TXC B
DCD A
DCD B
DSR A
DSR B
RTS A
RTS B
DCD A
DCD B
DTR A
DTR B
16109764
3 8 11 12 13
5
2
15 18 17 19 20 22
LTC1344A
C6
100pF C7
100pF C8
100pF
VCC
VCC
5V
23 24
14
1
DCE/DTE
M2
M1
M0
CHARGE
PUMP
+
28
3
1
2
4
5
6
7
8
9
10
11
12
13
14
27
26
25
24
23
22
21
20
19
18
17
16
15
VEE
DCE/DTE
M0
M1
M2
DTE DCE
21
LATCH
C12
1µF
C13
1µF
C11
1µF
C10
1µFC9
1µF
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen-
tation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
16
LTC1545
sn1545 1545fas LT/TP 1199 2K REV A • PRINTED IN
USA
LINEAR TECHNOLOGY CORPORATION 1998
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900
FAX: (408) 434-0507
www.linear-tech.com
Dimensions in inches (millimeters) unless otherwise noted.
PACKAGE DESCRIPTION
U
G Package
36-Lead Plastic SSOP (0.209)
(LTC DWG # 05-08-1640)
G36 SSOP 1098
0.13 – 0.22
(0.005 – 0.009)
0° – 8°
0.55 – 0.95
(0.022 – 0.037)
5.20 – 5.38**
(0.205 – 0.212)
7.65 – 7.90
(0.301 – 0.311)
12345678 9 10 11 12 14 15 16 17 1813
12.67 – 12.93*
(0.499 – 0.509)
2526 22 21 20 19232427282930313233343536
1.73 – 1.99
(0.068 – 0.078)
0.05 – 0.21
(0.002 – 0.008)
0.65
(0.0256)
BSC 0.25 – 0.38
(0.010 – 0.015)
NOTE: DIMENSIONS ARE IN MILLIMETERS
DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.152mm (0.006") PER SIDE
DIMENSIONS DO NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.254mm (0.010") PER SIDE
*
**
RELATED PARTS
PART NUMBER DESCRIPTION COMMENTS
LTC1321 Dual RS232/RS485 Transceiver Two RS232 Driver/Receiver Pairs or Two RS485 Driver/Receiver Pairs
LTC1322 Dual RS232/RS485 Transceiver Four RS232 Driver/Receiver Pairs or Two RS485 Driver/Receiver Pairs
LTC1334 Single 5V RS232/RS485 Multiprotocol Transceiver Two RS232 Driver/Receiver Pairs or Four RS232 Driver/Receiver Pairs
LTC1335 Dual RS232/RS485 Transceiver Four RS232 Driver/Receiver Pairs or Two RS485 Driver/Receiver Pairs
LTC1343 Software-Selectable Multiprotocol Transceiver 4-Driver/4-Receiver for Data and Clock Signals
LTC1344A Software-Selectable Cable Terminator Perfect for Terminating the LTC1543
LTC1345 Single Supply V.35 Transceiver 3-Driver/3-Receiver for Data and Clock Signals
LTC1346A Dual Supply V.35 Transceiver 3-Driver/3-Receiver for Data and Clock Signals
LTC1543 Software-Selectable Multiprotocol Transceiver Companion to LTC1544/LTC1545 for Data and Clock Signals
LTC1544 Software-Selectable Multiprotocol Transceiver 4-Driver/4-Receiver for Control Signals
LTC1387 Single 5V RS232/RS485 Multiprotocol Transceiver Two RS232 Driver/Receiver Pairs or One RS485 Driver/Receiver Pair