19-1825; Rev 1; 5/12 KIT ATION EVALU LE B A IL A AV 2.4GHz Monolithic Voltage-Controlled Oscillators The MAX2750/MAX2751/MAX2752 are self-contained voltage-controlled oscillators (VCOs) intended for use in the 2.4GHz to 2.5GHz ISM band. Each IC combines a fully integrated oscillator and output buffer in a miniature 8-pin MAX package. The inductor and varactor elements of the tank are integrated on-chip, greatly simplifying application of the part. The only required external components are a couple of supply bypass capacitors. The IC provides direct connection to the VCO tuning voltage input and the VCO buffer output. The tuning voltage input range is +0.4V to +2.4V, and the oscillator frequency tuning range is factory adjusted to provide guaranteed limits. The output signal is buffered by an amplifier stage (internally matched to 50) to provide higher output power and isolate the device from load impedance variations. The MAX2750/MAX2751/MAX2752 operate over a +2.7V to +5.5V supply voltage range. Internal regulation of the oscillator supply voltage eliminates the need for an external LDO regulator for the VCO. The IC also provides a digitally controlled shutdown mode to permit implementation of sophisticated power-supply management. In shutdown, the supply current is reduced to less than 1A. ________________________Applications 802.11b DSSS WLAN 802.11 FHSS WLAN Home RF 2.4GHz Bluetooth ISM Proprietary Radio Features Guaranteed Frequency Tuning Range MAX2750: 2400MHz to 2500MHz (Zero IF) MAX2751: 2120MHz to 2260MHz (240MHz to 280MHz IF) MAX2752: 2025MHz to 2165MHz (335MHz to 375MHz IF) On-Chip Tank Circuit Internally Matched Output Buffer Amplifier Low-Current Shutdown Mode +2.7V to +5.5V Supply Voltage Range Miniature 8-Pin MAX Package Ordering Information PART TEMP RANGE PIN-PACKAGE MAX2750EUA+ -40C to +85C 8 MAX MAX2751EUA+ -40C to +85C 8 MAX MAX2752EUA+ -40C to +85C 8 MAX +Denotes a lead(Pb)-free/RoHS-compliant package. Devices are also available in a tape-and-reel packaging. Specify tape and reel by adding "T" to the part number when ordering. Pin Configuration appears at end of data sheet. Typical Operating Circuit BYP GND TUNE TUNE OSCILLATOR CORE OUT OUT TO MIXER/ SYNTHESIZER GND VCC1 MAX2750 MAX2751 MAX2752 SHDN SHDN VCC VCC2 BIAS For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim's website at www.maxim-ic.com. 1 MAX2750/MAX2751/MAX2752 General Description MAX2750/MAX2751/MAX2752 2.4GHz Monolithic Voltage-Controlled Oscillators ABSOLUTE MAXIMUM RATINGS VCC to GND ..............................................................-0.3V to +6V TUNE, SHDN, BYP, OUT to GND ...............-0.3V to (VCC + 0.3V) Continuous Power Dissipation (TA = +70C) MAX (derate 4.8mW/C above TA = +70C)...........387.8mW Operating Temperature Range ...........................-40C to +85C Junction Temperature ......................................................+150C Storage Temperature Range .............................-65C to +150C Lead Temperature (soldering, 10s) .................................+300C Soldering Temperature (reflow) .......................................+260C Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. DC ELECTRICAL CHARACTERISTICS (VCC = +2.7V to +5.5V, VTUNE = +0.4V to +2.4V, V SHDN +2V, OUT = connected to 50 load, TA = -40C to +85C. Typical values are at VCC = +3.0V, TA = +25C, unless otherwise noted.) (Note 1) PARAMETER CONDITIONS Supply Voltage TYP 2.7 MAX2750 Supply Current MIN MAX2751 UNITS 5.5 V TA = +25oC 11.3 TA = -40oC to +85oC 14.1 17.0 TA = +25oC 9.7 12.1 TA = -40oC to +85oC 12.7 15.9 TA = +25oC MAX2752 MAX TA = -40oC to +85oC Shutdown Supply Current mA 10 12.1 12.8 15.2 0.2 1 A 0.6 V SHDN Input Voltage Low SHDN Input Voltage High 14.4 2.0 V SHDN Input Current Low V SHDN 0.6V -2 2 A SHDN Input Current High V SHDN 2.0V -2 2 A TUNE Input Current 0.4 V TUNE 2.4V 0.02 nA AC ELECTRICAL CHARACTERISTICS (MAX2750/MAX2751/MAX2752 EV kit, VCC = +2.7V to +5.5V, VTUNE = +0.4V to +2.4V, V SHDN +2V, OUT = connected to 50 load, TA = +25C. Typical values are at VCC = +3.0V, unless otherwise noted.) PARAMETER Oscillator Guaranteed Frequency Limits (Note1) Phase Noise CONDITIONS V TUNE = +0.4V to +2.4V, TA = -40oC to +85oC MAX UNITS MHz MAX2750 2400 2500 MAX2751 2120 2260 MHz MAX2752 2025 2165 MHz fOFFSET = 4MHz -125 dBc/Hz -151 dBm/Hz MAX2751 MAX2752 Output Power TYP Noise floor MAX2750 Tuning Gain (Note 2) MIN fOSC = 2400MHz, +3V 140 fOSC = 2500MHz, +3V 90 fOSC = 2120MHz, +3V 175 fOSC = 2260MHz, +3V 110 fOSC = 2025MHz, +3V 170 fOSC = 2165MHz, +3V 105 -3 MHz/V dBm Return Loss 12 dB Harmonics -30 dBc 2 2.4GHz Monolithic Voltage-Controlled Oscillators (MAX2750/MAX2751/MAX2752 EV kit, VCC = +2.7V to +5.5V, VTUNE = +0.4V to +2.4V, V SHDN +2V, OUT = connected to 50 load, TA = +25C. Typical values are at VCC = +3.0V, unless otherwise noted.) PARAMETER CONDITIONS Load Pulling VSWR = 2:1, all phases Supply Pushing VCC stepped: +3.3V to +2.8V Oscillator Turn-On Time (Note 3) Oscillator Turn-Off Time (Note 4) Note 1: Note 2: Note 3: Note 4: MIN TYP MAX UNITS 4 MHzp-p 1.3 MHz/V Exiting shutdown 8 s Entering shutdown 5 s Specifications are production tested at TA = +25C. Limits over temperature are guaranteed by design and characterization. Tuning gain is measured at the oscillator's guaranteed frequency limits. Turn-on time to within 3dB of final output power Turn-off time to output power of -10dBm. Typical Operating Characteristics (Circuit of Figure 1, VCC = +3.0V, VTUNE = +0.4V to +2.4V, V SHDN 2V, TA = +25C, unless otherwise noted.) MAX2750/MAX2751/MAX2752 SUPPLY CURRENT vs. TEMPERATURE 12 11 10 MAX2752 9 MAX2751 0.3 0.2 MAX2750/51/52 toc03 0.4 1.0 TUNE INPUT CURRENT (nA) MAX2750 13 MAX2750/51/52 toc02 SUPPLY CURRENT (mA) 14 0.5 SHUTDOWN CURRENT (A) MAX2750/51/52 toc01 15 MAX2750/MAX2751/MAX2752 TUNING CURRENT vs. TEMPERATURE MAX2750/MAX2751/MAX2752 SHUTDOWN CURRENT vs. TEMPERATURE 0.8 0.6 0.4 0.2 0.1 8 0 0 0 20 40 TEMPERATURE (C) 60 80 -40 -20 MAX2750 VCO TUNING CURVE 2400 TA = +25C 40 60 -40 80 0 0.5 1.0 1.5 VTUNE (V) 2.0 2.5 3.0 20 40 MAX2751 VCO TUNING CURVE MAX2752 VCO TUNING CURVE TA = +25C 2050 TA = +85C 60 2350 2250 80 TA = -40C 2150 2050 TA = +25C 1950 TA = +85C 1850 1850 2200 0 TEMPERATURE (C) 2150 1950 -20 TEMPERATURE (C) TA = -40C 2250 TA = +85C 2300 20 2350 FREQUENCY (MHz) TA = -40C 2500 FREQUENCY (MHz) MAX2750/51/52 toc04 2600 0 FREQUENCY (MHz) -20 MAX2750/51/52 toc05 -40 MAX2750/51/52 toc06 7 0 0.5 1.0 1.5 VTUNE (V) 2.0 2.5 3.0 0 0.5 1.0 1.5 2.0 2.5 3.0 VTUNE (V) 3 MAX2750/MAX2751/MAX2752 AC ELECTRICAL CHARACTERISTICS (continued) Typical Operating Characteristics (continued) (Circuit of Figure 1, VCC = +3.0V, VTUNE = +0.4V to +2.4V, V SHDN 2V, TA = +25C, unless otherwise noted.) -80 -90 -100 -110 -120 MKR -30.00dB = 30dBc OUTPUT POWER (dBm) -70 -2 MAX2750/51/52 toc08 -60 OUTPUT POWER (dBm) MAX2750/51/52 toc07 -50 -3 -4 MAX2750/51/52 toc09 NORMALIZED HARMONIC OUTPUT SPECTRUM MAX2751 OUTPUT POWER vs. TEMPERATURE PHASE NOISE PHASE NOISE (dBc/Hz) = 48dBc -130 -140 -150 -5 0.1 1 10 -40 -20 OFFSET FREQUENCY (MHz) 0 20 40 60 -40 -50 -60 8s MAX2750/51/52 toc11 -30 0 -10 -20 OUTPUT POWER (dBm) -20 -30 -40 -50 -60 4s -70 -80 -80 -90 -90 -100 -100 0 2 4 6 8 10 12 14 16 18 20 0 2 4 6 8 10 12 14 16 18 20 TIME (s) TIME (s) 4 3O OSCILLATOR TURN-OFF TIME MAX2750/51/52 toc10 -10 2O FREQUENCY OSCILLATOR TURN-ON TIME -70 O 80 TEMPERATURE (C) 0 OUTPUT POWER (dBm) MAX2750/MAX2751/MAX2752 2.4GHz Monolithic Voltage-Controlled Oscillators Pin Description PIN NAME FUNCTION 1 BYP 2 TUNE Oscillator Frequency Tuning Voltage Input. High-impedance input with a voltage input range of +0.4V (low frequency) to +2.4V (high frequency). 3 GND Ground Connection for Oscillator and Biasing. Requires a low-inductance connection to the circuit board ground plane. 4 SHDN Shutdown Logic Input. A high-impedance input logic level low disables the device and reduces supply current to less than 1.0A. A logic level high enables the device. 5 VCC1 Bias and Oscillator DC Supply Voltage Connection. Bypass separately from PIN6 with a 220pF capacitor to GND for low noise and low spurious content performance from the oscillator. 6 VCC2 Output Buffer DC Supply Voltage Connection. Bypass separately from PIN5 with a 220pF capacitor to GND for best high frequency performance. 7 OUT Buffered Oscillator Output. Incorporates an internal DC blocking capacitor. OUT is internally matched to 50. 8 GND Ground Connection for Output Buffer. Requires a low-inductance connection to the circuit board ground plane. VCO Bypass. Bypass with a 0.1F capacitor to GND. 2.4GHz Monolithic Voltage-Controlled Oscillators GND TUNE FROM SYNTHESIZER OSCILLATOR CORE OUT TO MIXER/ SYNTHESIZER OUT LOOP FILTER 220pF VCC1 GND VCC SHDN SHDN BIAS VCC2 220pF Figure 1. Typical Application Circuit Detailed Description Applications Information Oscillator Tune Input The MAX2750/MAX2751/MAX2752 VCOs are implemented as an LC oscillator topology, integrating all of the tank components on-chip. This fully monolithic approach provides an extremely easy-to-use VCO, equivalent to a VCO module. The frequency is controlled by a voltage applied to the TUNE pin, which is internally connected to the varactor. The VCO core uses a differential topology to provide a stable frequency versus supply voltage and improve the immunity to load variations. In addition, there is a buffer amplifier following the oscillator core to provide added isolation from load variations and to boost the output power. The tuning input is typically connected to the output of the PLL loop filter. The loop filter provides an appropriately low-impedance source. The input may incorporate an extra RC filter stage to reduce high-frequency noise and spurious signals. Any excess noise on the tuning input is directly translated into FM noise, which can degrade the phase-noise performance of the oscillator. Therefore, it is important to minimize the noise introduced on the tuning input. A simple RC filter with low corner frequency is needed during testing in order to filter the noise present on the voltage source driving the tuning line. Output Buffer Layout Issues The oscillator signal from the core drives an output buffer amplifier. The amplifier is internally matched to 50 including an on-chip DC blocking capacitor. No external DC blocking capacitor is required, eliminating the need for any external components. The output amplifier has its own VCC and GND pins to minimize load-pulling effects. The amplifier boosts the oscillator signal to a level suitable for driving most RF mixers. Always use controlled impedance lines (microstrip, coplanar waveguide, etc.) for high-frequency signals. Always place decoupling capacitors as close to the VCC pins as possible; for long VCC lines, it may be necessary to add additional decoupling capacitors located further from the device. Always provide a low-inductance path to ground, and keep GND vias as close to the device as possible. Thermal reliefs on GND pads are not recommended. 5 MAX2750/MAX2751/MAX2752 MAX2750 MAX2751 MAX2752 BYP 0.1F 2.4GHz Monolithic Voltage-Controlled Oscillators MAX2750/MAX2751/MAX2752 Pin Configuration Chip Information PROCESS: BiPOLAR TOP VIEW BYP 1 TUNE 2 GND 3 MAX2750 MAX2751 MAX2752 SHDN 4 MAX 6 8 GND 7 OUT 6 VCC2 5 VCC1 Package Information For the latest package outline information and land patterns (footprints), go to www.maxim-ic.com/packages. Note that a "+", "#", or "-" in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. PACKAGE TYPE PACKAGE CODE OUTLINE NO. LAND PATTERN NO. 8 MAX U8+1 21-0036 90-0092 2.4GHz Monolithic Voltage-Controlled Oscillators REVISION NUMBER REVISION DATE 0 10/00 1 5/12 DESCRIPTION Initial release PAGES CHANGED -- Added information for lead-free compliant options, added Absolute Maximum Ratings information, updated TOC 11 1, 2, 4 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical. Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance. Maxim Integrated Products, 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000 _____________________ 7 (c) 2012 Maxim Integrated Products Maxim is a registered trademark of Maxim Integrated Products, Inc. MAX2750/MAX2751/MAX2752 Revision History