POWER MP Series 400 - 1200 Watts Data Sheet Total Power: 400 - 1200 W Input Voltage: 85 - 264 VAC 120 - 350 VDC # of Outputs: Up to 21 Special features Current share on all outputs with ratings of 10 A or greater Remote sense on all outputs with ratings greater than 2 A Overload protection on all outputs Voltage adjustment on all outputs Margining on all single output modules Electrical Specifications Input Input range: 85 - 264 Vac 120 - 350 Vdc Frequency: 47 - 440 Hz 2 year warranty Inrush current: 40 A peak max. (soft start) Forced air cooling, field replaceable fan Efficiency: 70 - 80% typ. @ full case load Isolated 5 V bias voltage Power factor: 0.99 typ. meets EN61000-3-2 EN61000-3-2 harmonic distortion compliance Turn-on time: AC on 1.5 sec typ. inhibit/enable 150 ms typ. CISPR 22, EN55022 Curve B conducted/ radiated EMI EMI filter standard: CISPR 22/EN55022 Level "B" European CE Mark requirements EMI filter (low leakage option): CISPR 22/EN55022 Level "A" Optional VME timing and system DC OK module Leakage current standard: 2.0 mA max. @240 Vac Leakage current (low leakage option): 300A max. @ 240 Vac Radiated EMI: CISPR 22/EN55022 Level "B" Holdover storage: 20 ms minimum (independent of input Vac) AC OK: > 5 ms early warning min. before outputs lose regulation Full cycle ride thru (50 Hz) Harmonic distortion: Meets EN61000-3-2 Isolation: Meets EN60950 Efficiency: 70 - 80% typ. @ full case load Global Inhibit/Enable: TTL, Logic "1" and Logic "0" Input fuse (internal): MP4: 10 A; MP6: 15 A; MP8: 20 A; MP1: 20 A Warranty: 2 years Input OK signal and status indicator LED Global DC OK signal and status indicator LED Global and individual module inhibits/enable Power factor correction Customer-provided air option Additional 200 W output @ high line (180-264 VAC) Low leakage option for medical applications EN61000 immunity standards Standard modification flexibility (consult factory) * Low noise fan * Fan fail signal * Module enable * Outputs down to 0.5V Field Demonstrated MTBF: > 550,000 hours at full load, 220 Vac & 25 C ambient conditions SAFETY UL CSA IEC VDE BABT CB CE UL1950 CSA22.2 No. 234 Level 5 IEC950, Class 1 EN60950 Compliance to EN 60950, BS 7002 Certificate and report Mark MP Series Data Sheet Electrical Specifications Electrical Specifications Electrical Specifications Output Output (cont.) Adjustment range: 10% minimum all outputs Margining: 4 - 6% nominal1 Thermal protection: Overall regulation: 0.4% or 20mV max. (36 W modules 4% maximum) All outputs disabled when internal temp exceeds safe operating range. > 5 ms warning (AC OK signal) before shutdown Remote sense: Up to 0.5 V total drop (not avbl on triple output module) Ripple: RMS: 0.1% or 10 mV, whichever is greater Pk-Pk: 1.0% or 50 mV, whichever is greater Bandwidth limited to 20 MHz Single wire parallel: Current share to within 2% of total rated current2 DC OK: -2% to -8% of nominal for any monitored output2 Dynamic response: < 2% or 100 mV, with 25% load step Minimum load: Recovery time: To within 1% in < 300 sec Not required on single or triple output. 10% required on main of dual output3 Overcurrent protection:** Single output module & main output of dual output module Housekeeping bias voltage: 5 Vdc @ 1.0 A max. present whenever AC input is applied Module inhibit: TTL, isolated, singles and dual (both outputs) only Aux output of dual output module 105 -140% of rated output current Switching frequency: 250k Hz Short-circuit protection: Protected for continuous short-circuit Recovery auto upon removal of short Output/Output isolation: > 1 Megohm VME signal option board: POR signal & quad external DC OK Overvoltage protection: (measured at sense connection) Single output module: 2 - 5.5 V 122 - 134%; 6 - 60 V 100 - 120% Hold-up module (HUP): 1-slot module providing additional 34 mSec (60 mSec total); hold-up @ 600 W loading. Dual output module: 2 - 6 V 122 - 134%; 8 - 28 V 110 - 120% Field Demonstrated MTBF: > 550,000 hours at full load, 220 Vac and 25 C ambient conditions 105-120% of rated output current. Triple output module: No overvoltage protection provided. Recycle AC input voltage to reset OVP circuit Reverse voltage protection: 1. Single output modules only. 2. Single and main of dual output modules only 3. Contact factory for optional preload if required 100% of rated output current Environmental Specifications Operating temperature: -20 C to 50 C (start @ 0 C) (derate each output linearly to 50% at 70 C) (-20 C to 40 C max. with rear air option) Shock/Vibration: Mil-Hdbk 810E Humidity: 95% non-condensing Storage temperature: -40 C to 85 C Temperature coefficient: 0.02% per C Cooling: Internal DC fan or customer provided air (option) Output Module Line-up Module Type Output: Max output power: Max output current: Volts: Single Single 1 1 210 W 360 W Single 600 W Dual Triple 2 3 144 W 36 W 120 mV 35 A 60 A 120 A 10 A 2A 2 - 60 V 2 - 60 V 2 - 60 V 2 - 28 V 2 - 28 V Standard voltage increments: 25 25 25 19 18 Remote sense on outputs: Yes Yes Yes Yes, both No Remote margin/V-Program: Yes Yes Yes No No Module Inhibit (isolated): Yes Yes Yes - - Single wire active current share: Yes Yes Yes Yes, main only - Over voltage/over current protection: Yes Yes Yes Yes Over current Minimum load required: No No No Yes (10%) main only No 1 2 3 1 1 Slots occupied in any MP case: MP Series Data Sheet Output Module Voltage/Current 2.4 - 2.7 V 35 A 60 A 120 A -- 10 A -- -- 2A 3.6 - 4.5 V 35 A 60 A 120 A -- 10 A -- -- 2A 6.6 - 9.2 V 20 A 36 A 68 A 10 A 4A -- -- 1A 8.8 - 9.0 V 18 A 32 A 60 A 10 A 4A -- -- 1A 7 6 5 4 Slot 1 Slot 1 V3 2A 2A 2A 2A 2A 2A 2A 2A 1A 1A 1A 1A 1A 1A 0.5 A 0.5 A 0.5 A 0.5 A -- -- -- -- -- -- -- Slot 3 Slot 3 Slot 3 2 3 V1 V2 V1 V2 60 A 120 A -- 10 A -- -- 60 A 120 A -- 10 A -- -- 60 A 120 A -- 10 A -- -- 60 A 120 A -- 10 A -- -- 60 A 120 A 10 A 10 A -- -- 60 A 115 A -- 10 A -- -- 58 A 109 A 10 A -- -- -- -- -- 42 A 78 A -- 10 A 36 A 68 A -- -- 1A 1A 32 A 60 A -- -- 1A 1A -- 31 A 54.5 A -- 1A 1A 30 A 50 A 10 A 4A 1A 1A 21 A 40.5 A 9A 4A 1A 1A 8A 4A 1A 1A 20 A 39 A 19 A 33.3 A -- -- -- 0.5 A 18 A 30 A -- -- -- 0.5 A 15 A 23.5 A 4A 2A -- 0.5 A 12.8 A 21.4 A 3A 2A -- 0.5 A 12 A 20 A -- -- -- -- 10.9 A 18.2 A -- -- -- -- 10 A 16.6 A -- -- -- -- 7.5 A 12.5 A -- -- -- -- 7.5 A 12.5 A -- -- -- -- 6.0 A 11 A -- -- -- -- 6.0 A 10 A -- -- -- -- Special Voltage - Consult Factory for specifications Slot 2 Slot 2 Slot 2 Parallel Codes Triple Output Slot 5 Slot 5 Slot 5 1 35 A 35 A 35 A 35 A 35 A 35 A 34 A 23 A 20 A 18 A 17 A 17 A 14 A 14 A 11 A 10.5 A 8.5 A 6.7 A 6.5 A 6.2 A 5.8 A 4.2 A 4.0 A 3.7 A 3.5 A Dual Output** Slot 4 Slot 4 Slot 4 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z Single Output Module Code Slot 7 2V 2.2 V 3V 3.3 V 5V 5.2 V 5.5 V 6.0 V 8.0 V 10 V 11 V 12 V 14 V 15 V 18 V 20 V 24 V 28 V 30 V 33 V 36 V 42 V 48 V 54 V 60 V Non-std* Voltage Code Slot 6 Slot 6 Voltage 3 2 1 MP4 & MP6 available slots MP8 available slots MP1 available slots 0 = no parallel 1=1&2 2=2&3 3=3&4 4=4&5 5=3&4&5 6=5&6 7=4&5&6 8=6&7 9 = 3 & 4, 6 & 7 A = 1 & 2, 3 & 4, 5 & 6 C = 2 & 3, 4 & 5 E = 3 & 4, 5 & 6 F = 2 & 3, 4 & 5, 6 & 7 Notes: 1. Omit digits that do not apply. 2. Specify modules from lowest number of outputs to highest. (Single/Dual/Triple) 3. If number of outputs are equal, specify modules from highest to lowest power increments. If power increments are equal, specify in descending alphabetical order (1A, B, C . . .). 4. Always start with Slot 1. 5. All MP model configurations created using this selection guide are standard MP products with standard availability and lead times. 6. Optional VME/DCOK module must always be located in the last slot. Module designator is "VME". Ordering Information Case Size MP1 Case Size (mm) 4 = 2.5" x 5" x 10"; 400 - 600 W, 5 Slots (63.5 x 127 x 254) 6 = 2.5" x 5" x 11"; 600- 800 W, 5 Slots (63.5 x 127 x 279.4) 8 = 2.5" x 7" x 10"; 800 - 1000 W, 6 Slots (63.5 x 177.8 x 254) 1 = 2.5" x 8" x 11"; 1000 - 1200 W, 7 Slots* (63.5 x 203.2 x 279.4) Module/Voltage/Option Codes First - Module Code Second - Voltage Code - 3L - 2E - 1Q - 4LL Module Codes Module/Voltage/Option Codes Module codes: (None) = 36 W triple O/P (1 slot) 1 = 210 W single O/P (1 slot) 2 = 360 W single O/P (2 slot) 3 = 600 W single O/P (3 slot) 4 = 144 W dual O/P (1 slot) 5 - 9 = future Voltage Codes: See Output Module Voltage/ Current table above Add-on Modules - HUP HUP = Hold up module VME = VME POR signal and isolated DC Case Option Codes - 00 Case Option Codes First digit 0 - 9, A - Z parallel code (See Parallel Codes table above) Second digit Standard Options 0 = No options 1 = Rear Air Exhaust 3 = Global enable 5 = Opt 1 + Opt 3 M = Low Leakage N = Low Leakage + Opt 1 P = Low Leakage + Opt 3 R = Low Leakage + Opt 5 Hardware Code -### Factory assigned for modifications MP Series Data Sheet Single MP4 & MP6 4.3 .8 -A- 23.9 .5 (4 PL) .17 .03 .94 .02 NON-CUMULATIVE Input 85-264 Vac 180-264 Vac MP4 = 2.5" x 5" x 10" 5 available slots (63.5 x 127 x 254 mm) MP6 = 2.5" x 8" x 11"5 available slots (63.5 x 127 x 279.4 mm) 210 W MP8 400 W max. 600 W max. 600 W max. 800 W max. 177.8 7.0 AC INPUT 360 W S L O T S L O T S L O T S L O T S L O T S L O T 6 5 4 3 2 1 OUTPUT MODULE AREA Input 85-264 Vac 180-264 Vac MP8 = 2.5" x 7" x 10" 6 available slots (63.5 x 177.8 x 254 mm) 800 W max. 1000 W max. MP1 600 W Dual Input 85-264 Vac 180-264 Vac MP1 = 2.5" x 8" x 11"7 available slots (63.5 x 203.2 x 279.4 mm) 1000 W max. 1200 W max. Pin Connectors 144 W Figure 1. Connector J1 PFC Input Connector J1 Control Connector Triple Mates with Molex 90142-0010 Housing 90119-2110 Pin Standard for all cases Pin No. Function J1-1 J1-2 J1-3 J1-4 J1-5 J1-6 J1-7 J1-8 J1-9 J1-10 Input AC OK - "emitter" Input AC OK - "collector" Global DC OK - "emitter" Global DC OK - "collector" Spare Global inhibit/optional enable logic "0" Global inhibit/optional enable logic "1" Global inhibit/optional enable return SELV 5 V housekeeping SE:V 5 V housekeeping return MP Series Data Sheet Mechanical Drawings MP Modules Single 210 Watt DC-DC Converter Output Modules .44 (11.2 ) PFC Input Connector Pin No. Function 1 2 3 4 5 6 7 8 9 + Remote Sense Remote Margin / V. Program N 1 Margin High - Remote Sense/Margin Low 2 Spare 3 Module, Isolated Inhibit Module Inhibit Return Current Share (SWP) + Remote Sense V2 single or dual o/p main single o/p single o/p single or dual o/p main 10 - Remote Sense V2 dual o/p, single is spare ~ M4X8 SCREWS (2X) .48 (12.1) single or dual o/p single or dual o/p single or dual o/p main dual o/p, single is spare 1 5 6 10 Mates with Molex 90142-0010 Housing 90119-2110 Pin V ADJ .44 (11.3) Single 600 Watt .59 (15.0) .63 (16.0) V+ V ADJ V+ V.44 (11.3) VPIN 1 .63 (16.0) M4X8 SCREWS (4X) .61 (15.6) 1.24 (31.6) (2X) (2X) (2X) .48 (12.1) M4X8 SCREWS (4X) PIN 1 .32 (8.1) Single 360 Watt .33 (8.5) V- 1.38 (35.1) Figure 4. Connector J1 1.38 (35.1) (2X) .44 (11.3) V+ (2X) V ADJ .32 (8.1) .32 (8.1) PIN 1 Triple 36 Watt Dual 144 Watt .46 (11.7) V1 + V1 ADJ (4X) V1 V2 + V2 ADJ V2 - .30 (7.5) (3X) PIN 1 1.17 (29.7) .42 (10.7) .32 (8.1) V2 ADJ V1 ADJ PIN 1 .84 (21.3) M3X8 SCREWS (4X) DC OUTPUT CONNECTION .48 (12.1) V3 ADJ V1+ V1V2+ V2V3+ V3- MP Series Data Sheet MP Series MP4 (400/600 Watts Max) MP6 (600/800 Watts Max) 5-Inch Case Size: MP4: 2.5" x 5" x 10" (63.5 mm x 127mm x 254 mm) 5-Inch Case Size: MP6: 2.5" x 5" x 11" (63.5 mm x 127 mm x 279.4mm) Weight: MP4 Case: 2.6 lbs. * MP6 Case: 3.2 lbs. * 36 W Triple: 0.5 lb.* 210 W Single: 0.6 lb * Single O/P: 0.22 lb. * Dual O/P: 0.16 lb. * Blank: 0.06 lb. #8-32 MTG HOLES 4 PL MARKED "A" 171.45 19.05 6.750 .750 M4 MTG HOLES 4 PL MARKED "B" A B B Standard Airflow 101.60 4.000 A B A B 171.45 29.05 12.70 6.750 1.144 .500 3.5 .14 (TYP ) M4 MTG HOLES 4 PL 38.10 63.5 +.0 -.5 1.500 2.50 +.00 -.02 17.3 + - 1.0 .68 + -.04 MP4 0 254.0 +. -.5 10.00 +.00 -.02 MP6 279.4 +.0 -.5 19.05 .750 171.45 6.750 11.00 +.00 -.02 12.70 .500 3.7 .15TYP MOUNTING HOLES DIMENSIONS IDENTICAL ON BOTH SIDES +.0 127.0 -.5 +.00 5.00 -.02 19.0 .75 1 49.2 1.94 2 Notes: 1. Input: Barrier type. Three No. 6-32 B.H. screws (0.375" centers). Max torque: 6 in-lbs. (0.67 N-m). 2. Control connectors: (J1 and J2) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III Series). Connector kit includes mating connector and 10 pins, Astec part #70-841-004. 3. Chassis material: aluminum with chemical film coating (conductive). 4. All dimensions are in millimeters and inches, and are typical. 5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.150" (3.8 mm). Max. torque: 5 in-lbs. 6. Output module connections: All single O/P modules are M4 x 8 mm screws. Max. torque: 10 in-lbs. Dual O/P module is M3 x 8 mm screws. Max. torque: 5 in-lbs. Triple O/P module is .045" square pins on .156" centers. Mates with Moelx 09-50-8063 or equivalent. MP Series Data Sheet MP Series MP8 (800/1000 Watts Max) 7-Inch Case Size: MP8: 2.5" x 7" x 10" (63.5 mm x 177.8 mm x 254 mm) Weight: MP8 Case: 4.1 lbs. * 36 W Triple: 0.5 lb. * 210 W Single: 0.6 lb. * 360 W Single: 1.0 lb. * 600 W Single: 2.6 lbs. * 144 W Dual: 0.6 lb. 12.70 0.5 254 10.0 M4 MOUNTING HOLES MARKED "B" (4X) "A" Standard Airflow 171.45 6.75 19.05 0.75 "B" "A" "B" "A" "B" 152.40 6.0 "A" "B" 171.45 6.75 #8-32 MOUNTING HOLES MARKED "A" (4X) 29.05 1.1 19.05 0.7 171.45 6.75 38.10 1.5 35.0 1.38 63.5 2.5 M4 MOUNTING HOLES (4X) 254 10.0 12.70 0.5 60.5 2.38 59.5 2.34 14.7 0.58 31.8 1.25 177.8 7.0 14.0 0.55 63.5 2.5 2 Notes: 1. Input: Barrier type. Three No. 6-32 B.H. screws (0.375" centers). Max torque: 6 in-lbs. (0.67 N-m). 2. Control connectors: (J1 and J2) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III Series). Connector kit includes mating connector and 10 pins, Astec part #70-841-004. 3. Chassis material: aluminum with chemical film coating (conductive). 4. All dimensions are in millimeters and inches, and are typical. 5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.150" (3.8 mm). Max. torque: 5 in-lbs. 6. Output module connections: All single O/P modules are M4 x 8 mm screws. Max. torque: 10 in-lbs. Dual O/P module is M3 x 8 mm screws. Max. torque: 5 in-lbs. Triple O/P Module is .045" square pins on .156 centers. Mates with Moelx 09-50-8063 or equivalent. MP Series Data Sheet MP Series MP1 (1000/1200 Watts Max) M4 MTG HOLES 4 PL 8-Inch Case Size: MP1: 2.5" x 8" x 11" (63.5 mm x 203.2 mm x 279.4 mm) Weight: MP1 Case: 5.0 lbs. * 36 W Triple: 0.5 lb. * 210 W Single: 0.6 lb. * 360 W Single: 1.0 lb. * 600 W Single: 2.0 lbs. * 144 W Dual: 0.6 lb. MOUNTING HOLES - DIMENSIONS IDENTICAL ON BOTH SIDES 38.10 1.500 35.0 1.38 19.05 .750 171.45 6.750 12.70 .500 16.50 6.50 279.4 11.00 #8-32 MTG HOLES 4 PL MARKED "A" 171.45 6.750 STD AIR FLOW M4 MTG HOLES 4 PL MARKED "B" 19.05 .750 BOTTOM MOUNTING SURFACE 177.80 7.000 171.45 6.750 Notes: 1. Input: Barrier type. Three No. 6-32 B.H. screws (0.375" centers). Max torque: 6 in-lbs (0.67 N-m). 2. Control connectors: (J1 and J2) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III Series). Connector kit includes mating connector and 10 pins, Astec part #70- 841-004. 3. Chassis material: aluminum with chemical film coating (conductive). 4. All dimensions are in millimeters and inches, and are typical. 5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.150" (3.8 mm). Max. torque: 5 in-lbs. 6. Output module connections: All single O/P modules are M4 x 8 mm screws. Max. torque: 10 in-lbs. Dual O/P module is M3 x 8 mm screws. Max. torque: 5 in-lbs. Triple O/P module is .045" square pins on .156 centers. Mates with Molex 09-50-8063 or equivalent. 29.05 1.144 12.70 .500 203.2 8.00 14.7 .58 31.8 1.25 2 76.2 3.00 14.0 .55 69.9 2.75 WORLDWIDE OFFICES Americas Europe (UK) Asia (HK) 2900 S.Diablo Way Tempe, AZ 85282 USA +1 888 412 7832 Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom +44 (0) 1384 842 211 14/F, Lu Plaza 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong +852 2176 3333 While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. (c) 2014 All rights reserved. www.artesyn.com For more information: www.artesyn.com/power For support: productsupport.ep@artesyn.com MP DS Rev. 03.10.14 63.5 2.50