MP6-3T-4LL-00 - Artesyn Embedded Technologies

POWER

MP Series

400 - 1200 Watts

Total Power: 400 - 1200 W

Input Voltage: 85 - 264 VAC

120 - 350 VDC

# of Outputs: Up to 21

SPECIAL FEATURES

Current share on all outputs with

ratings of 10 A or greater

Remote sense on all outputs with

ratings greater than 2 A

Overload protection on all outputs

Voltage adjustment on all outputs

Margining on all single output modules

Input OK signal and status indicator LED

Global DC OK signal and status indicator LED

Global and individual module inhibits/enable

2 year warranty

Forced air cooling, ﬁeld replaceable fan

Isolated 5 V bias voltage

Power factor correction

EN61000-3-2 harmonic distortion compliance

CISPR 22, EN55022 Curve B conducted/

radiated EMI

European CE Mark requirements

Optional VME timing and system DC OK

module

Customer-provided air option

Additional 200 W output @ high line

(180-264 VAC)

Low leakage option for medical applications

EN61000 immunity standards

Standard modiﬁcation ﬂexibility

(consult factory)

• Low noise fan

• Fan fail signal

• Module enable

• Outputs down to 0.5V

Field Demonstrated MTBF: > 550,000 hours

at full load, 220 Vac & 25 °C ambient

conditions

SAFETY

UL UL1950

CSA CSA22.2 No. 234 Level 5

IEC IEC950, Class 1

VDE EN60950

BABT Compliance to EN 60950,

BS 7002

CB Certiﬁcate and report

CE Mark

Electrical Specications

Input

Input ra nge: 85 - 264 Vac

120 - 350 Vdc

Frequency: 47 - 440 Hz

Inrush current: 40 A peak max. (soft start)

Efciency: 70 - 80% typ. @ full case load

Power factor: 0.99 typ. meets EN61000-3-2

Turn-on time: AC on 1.5 sec typ.

inhibit/enable 150 ms typ.

EMI lter standard: CISPR 22/EN55022 Level “B”

EMI lter (low leakage option): CISPR 22/EN55022 Level “A”

Leakage current standard: 2.0 mA max. @240 Vac

Leakage current (low leakage option): 300μA max. @ 240 Vac

Radiated EMI: CISPR 22/EN55022 Level “B”

Holdover storage: 20 ms minimum (independent of input Vac)

AC OK: > 5 ms early warning min. before outputs lose regulation

Full cycle ride thru (50 Hz)

Harmonic distortion: Meets EN61000-3-2

Isolation: Meets EN60950

Efciency: 70 - 80% typ. @ full case load

Global Inhibit/Enable: TTL, Logic “1” and Logic “0”

Input fuse (internal): MP4: 10 A; MP6: 15 A; MP8: 20 A; MP1: 20 A

Warranty: 2 years

Data Sheet

MP Series Data Sheet

Environmental Specications

Operating temperature: -20 °C to 50 °C (start @ 0 °C)

(derate each output linearly to 50% at 70 °C)

(-20 °C to 40 °C max. with rear air option)

Shock/Vibration: Mil-Hdbk 810E

Humidity: 95% non-condensing

Storage temperature: -40 °C to 85 °C

Temperature coefcient: 0.02% per °C

Cooling: Internal DC fan or customer provided air (option)

Electrical Specications

Output

Adjustment range: ± 10% minimum all outputs

Margining: ± 4 - 6% nominal1

Overall regulation: 0.4% or 20mV max.

(36 W modules 4% maximum)

Ripple:

RMS: 0.1% or 10 mV, whichever is greater

Pk-Pk: 1.0% or 50 mV, whichever is greater

Bandwidth limited to 20 MHz

Dynamic response: < 2% or 100 mV, with 25% load step

Recovery time: To within 1% in < 300 μsec

Overcurrent protection:** Single output module & main output of dual

output module

105-120% of rated output current.

Aux output of dual output module 105 -140%

of rated output current

Short-circuit protection: Protected for continuous short-circuit

Recovery auto upon removal of short

Overvoltage protection:

(measured at sense

connection)

Single output module: 2 - 5.5 V 122 - 134%;

6 - 60 V 100 - 120%

Dual output module: 2 - 6 V 122 - 134%;

8 - 28 V 110 - 120%

Triple output module: No overvoltage

protection provided. Recycle AC input voltage

to reset OVP circuit

Reverse voltage protection: 100% of rated output current

Electrical Specications

Output (cont.)

Thermal protection:

All outputs disabled when internal temp exceeds

safe operating range. > 5 ms warning (AC OK

signal) before shutdown

Remote sense: Up to 0.5 V total drop (not avbl on triple output

module)

Single wire parallel: Current share to within 2% of total rated current2

DC OK: -2% to -8% of nominal for any monitored output2

Minimum load: Not required on single or triple output. 10%

required on main of dual output3

Housekeeping bias

voltage:

5 Vdc @ 1.0 A max. present whenever AC input

is applied

Module inhibit: TTL, isolated, singles and dual (both outputs)

only

Switching frequency: 250k Hz

Output/Output isolation: > 1 Megohm

VME signal option board: POR signal & quad external DC OK

Hold-up module (HUP): 1-slot module providing additional 34 mSec

(60 mSec total); hold-up @ 600 W loading.

Field Demonstrated MTBF: > 550,000 hours at full load, 220 Vac and

25 °C ambient conditions

1. Single output modules only.

2. Single and main of dual output modules only

3. Contact factory for optional preload if required

Electrical Specications

Output Module Line-up

Module Type Single Single Single Dual Triple

Output: 1 1 2 3

Max output power: 210 W 360 W 600 W 144 W 36 W 120 mV

Max output current: 35 A 60 A 120 A 10 A 2 A

Volts: 2 - 60 V 2 - 60 V 2 - 60 V 2 - 28 V 2 - 28 V

Standard voltage increments: 25 25 25 19 18

Remote sense on outputs: Yes Yes Yes Yes, both No

Remote margin/V-Program: Yes Yes Yes No No

Module Inhibit (isolated): Yes Yes Yes – –

Single wire active current share: Yes Yes Yes Yes, main only –

Over voltage/over current protection: Yes Yes Yes Yes Over current

Minimum load required: No No No Yes (10%) main only No

Slots occupied in any MP case: 1 2 3 1 1

MP Series Data Sheet

Output Module Voltage/Current

Ordering Information

Voltage Voltage

Code

Single Output Module Code Dual Output** Triple Output

1 2 3 V1 V2 V1 V2 V3

2 V A 35 A 60 A 120 A — 10 A — — 2 A

2.2 V B 35 A 60 A 120 A — 10 A — — 2 A

3 V C 35 A 60 A 120 A — 10 A — — 2 A

3.3 V D 35 A 60 A 120 A — 10 A — — 2 A

5 V E 35 A 60 A 120 A 10 A 10 A — — 2 A

5.2 V F 35 A 60 A 115 A — 10 A — — 2 A

5.5 V G 34 A 58 A 109 A —10 A — — 2 A

6.0 V H 23 A 42 A 78 A — 10 A — — 2 A

8.0 V I 20 A 36 A 68 A — — 1 A 1 A 1 A

10 V J 18 A 32 A 60 A — — 1 A 1 A 1 A

11 V K 17 A 31 A 54.5 A —— 1 A 1 A 1 A

12 V L 17 A 30 A 50 A 10 A 4 A 1 A 1 A 1 A

14 V M 14 A 21 A 40.5 A 9 A 4 A 1 A 1 A 1 A

15 V N 14 A 20 A 39 A 8 A 4 A 1 A 1 A 1 A

18 V O 11 A 19 A 33.3 A — — — 0.5 A 0.5 A

20 V P 10.5 A 18 A 30 A — — — 0.5 A 0.5 A

24 V Q 8.5 A 15 A 23.5 A 4 A 2 A — 0.5 A 0.5 A

28 V R 6.7 A 12.8 A 21.4 A 3 A 2 A — 0.5 A 0.5 A

30 V S 6.5 A 12 A 20 A — — — — —

33 V T 6.2 A 10.9 A 18.2 A — — — — —

36 V U 5.8 A 10 A 16.6 A — — — — —

42 V V 4.2 A 7.5 A 12.5 A — — — — —

48 V W 4.0 A 7.5 A 12.5 A — — — — —

54 V X 3.7 A 6.0 A 11 A — — — — —

60 V Y 3.5 A 6.0 A 10 A — — — — —

Non-std* Z Special Voltage - Consult Factory for specications

2.4 - 2.7 V 35 A 60 A 120 A — 10 A — — 2 A

3.6 - 4.5 V 35 A 60 A 120 A — 10 A — — 2 A

6.6 - 9.2 V 20 A 36 A 68 A 10 A 4 A — — 1 A

8.8 - 9.0 V 18 A 32 A 60 A 10 A 4 A — — 1 A

MP1 - 3L - 2E - 1Q - 4LL - HUP - 00 -###

Case Size (mm)

4 = 2.5” x 5” x 10”; 400 - 600 W, 5 Slots

(63.5 x 127 x 254)

6 = 2.5” x 5” x 11”; 600- 800 W, 5 Slots

(63.5 x 127 x 279.4)

8 = 2.5” x 7” x 10”; 800 - 1000 W, 6 Slots

(63.5 x 177.8 x 254)

1 = 2.5” x 8” x 11”; 1000 - 1200 W, 7 Slots*

(63.5 x 203.2 x 279.4)

Module Codes

Module/Voltage/Option Codes

Module codes:

(None) = 36 W triple O/P (1 slot)

1 = 210 W single O/P (1 slot)

2 = 360 W single O/P (2 slot)

3 = 600 W single O/P (3 slot)

4 = 144 W dual O/P (1 slot)

5 - 9 = future

Case Option Codes

First digit

0 - 9, A - Z parallel code

(See Parallel Codes table above)

Second digit

Standard Options

0 = No options

1 = Rear Air Exhaust

3 = Global enable

5 = Opt 1 + Opt 3

M = Low Leakage

N = Low Leakage + Opt 1

P = Low Leakage + Opt 3

R = Low Leakage + Opt 5

Add-on Modules

Voltage Codes:

See Output Module Voltage/

Current table above

Module/Voltage/Option Codes

First - Module Code

Second - Voltage Code

Case Option Codes

HUP = Hold up module

VME = VME POR signal

and isolated DC

Case Size

Factory assigned

for modifications

Hardware Code

7 6 5 4 3 2 1

MP4 & MP6

available slots

MP8

available slots

Slot 1

Slot 2

Slot 3

Slot 4

Slot 5

Slot 1

Slot 2

Slot 3

Slot 4

Slot 5

Slot 6

Slot 2

Slot 3

Slot 4

Slot 6

Slot 7

Slot 5

MP1

available slots

Parallel Codes

0 = no parallel

1 = 1 & 2

2 = 2 & 3

3 = 3 & 4

4 = 4 & 5

5 = 3 & 4 & 5

6 = 5 & 6

7 = 4 & 5 & 6

8 = 6 & 7

9 = 3 & 4, 6 & 7

A = 1 & 2, 3 & 4, 5 & 6

C = 2 & 3, 4 & 5

E = 3 & 4, 5 & 6

F = 2 & 3, 4 & 5, 6 & 7

Notes:

1. Omit digits that do not apply.

2. Specify modules from lowest number of outputs to highest. (Single/Dual/Triple)

3. If number of outputs are equal, specify modules from highest to lowest power

increments. If power increments are equal, specify in descending alphabetical

order (1A, B, C . . .).

4. Always start with Slot 1.

5. All MP model congurations created using this selection guide are standard MP

products with standard availability and lead times.

6. Optional VME/DCOK module must always be located in the last slot. Module

designator is “VME”.

MP Series Data Sheet

AC INPUT S

177.8

7.0

OUTPUT MODULE AREA

(4 PL)

4.3 ± .8

.17 ± .03

23.9 ± .5

.94 ± .02

-A-

NON-CUMULATIVE

MP4 & MP6

MP8

Mates with

Molex 90142-0010 Housing

90119-2110 Pin

Figure 1. Connector J1

Input

85-264 Vac 180-264 Vac

MP4 = 2.5” x 5” x 10” 5 available slots 400 W max. 600 W max.

(63.5 x 127 x 254 mm)

MP6 = 2.5” x 8” x 11” 5 available slots 600 W max. 800 W max.

(63.5 x 127 x 279.4 mm)

Input

85-264 Vac 180-264 Vac

MP8 = 2.5” x 7” x 10” 6 available slots 800 W max. 1000 W max.

(63.5 x 177.8 x 254 mm)

Input

85-264 Vac 180-264 Vac

MP1 = 2.5” x 8” x 11” 7 available slots 1000 W max. 1200 W max.

(63.5 x 203.2 x 279.4 mm)

210 W

360 W

600 W

144 W

MP1

Pin Connectors

PFC Input Connector

J1 Control Connector Standard for all cases

Pin No. Function

J1-1 Input AC OK - “emitter”

J1-2 Input AC OK - “collector”

J1-3 Global DC OK - “emitter”

J1-4 Global DC OK - “collector”

J1-5 Spare

J1-6 Global inhibit/optional enable logic “0”

J1-7 Global inhibit/optional enable logic “1”

J1-8 Global inhibit/optional enable return

J1-9 SELV 5 V housekeeping

J1-10 SE:V 5 V housekeeping return

Single

Dual

Triple

MP Series Data Sheet

Mechanical Drawings

PIN 1

V+

M4X8 SCREWS (4X)

V-

V ADJ

.32 (8.1)

.44 (11.3)

(2X) (2X)

.33 (8.5)

.63 (16.0)

.48 (12.1)

1.38 (35.1)

PIN 1

V2 ADJ

.32

(8.1)

.42 (10.7)

V1 +

V1 -

V2 -

V2 +

M3X8 SCREWS (4X)

.46 (11.7)

(4X)

.30 (7.5)(3X)

V1 ADJ

1.17 (29.7)

Single 210 Watt

Dual 144 Watt

Single 360 Watt

Single 600 Watt

MP Modules

DC-DC Converter Output Modules

Triple 36 Watt

V2 ADJ

V1 ADJ

PIN 1

V3 ADJ

DC OUTPUT CONNECTION

.48

(12.1)

.84

(21.3)

M4X8 SCREWS (4X)

V-

PIN 1

V ADJ

V+

.44

(11.3)

.32

(8.1)

1.24 (31.6) (2X)

.61 (15.6)

(2X)

.63

(16.0)

.59

(15.0)

V1+

V1-

V2+

V2-

V3+

V3-

Mates with

Molex 90142-0010 Housing

90119-2110 Pin

Figure 4. Connector J1

PFC Input Connector

Pin No. Function

1 + Remote Sense single or dual o/p main

2 Remote Margin / V. Program single o/p

3 Margin High single o/p

4 - Remote Sense/Margin Low single or dual o/p main

5 Spare

6 Module, Isolated Inhibit single or dual o/p

7 Module Inhibit Return single or dual o/p

8 Current Share (SWP) single or dual o/p main

9 + Remote Sense V2 dual o/p, single is spare

10 - Remote Sense V2 dual o/p, single is spare PIN 1

.32

(8.1)

.44 (11.2 )

(2X)

V+

M4X8 SCREWS (2X)

V-

V ADJ

.48 (12.1)

.44 (11.3)

1.38

(35.1)

MP Series Data Sheet

19.05

.750

171.45

6.750

29.05

1.144

171.45

6.750

M4 MTG HOLES

4 PL

MARKED "B"

#8-32 MTG HOLES

4 PL

MARKED "A"

101.60

4.000

12.70

.500

Standard Airow

+.0

-.5

127.0

+.00

-.02

5.00

19.0

.75

49.2

1.94

+.0

-.5

254.0

+.00

-.02

10.00 3.7

.15TYP

19.05

.750

+.0

-.5

63.5

+.00

-.02

2.50

3.5

.14 (TYP )

M4 MTG HOLES 4 PL

MOUNTING HOLES DIMENSIONS IDENTICAL ON BOTH SIDES

17.3 1.0

.68 .04

171.45

6.750

38.10

1.500

12.70

.500

MP4 +.0

-.5

279.4

+.00

-.02

11.00

MP6

MP Series

MP4 (400/600 Watts Max)

MP6 (600/800 Watts Max)

5-Inch Case Size: MP4: 2.5” x 5” x 10” (63.5 mm x 127mm x 254 mm)

5-Inch Case Size: MP6: 2.5” x 5” x 11” (63.5 mm x 127 mm x 279.4mm)

Weight: MP4 Case: 2.6 lbs. • MP6 Case: 3.2 lbs. • 36 W Triple: 0.5 lb.• 210 W Single: 0.6 lb

• Single O/P: 0.22 lb. • Dual O/P: 0.16 lb. • Blank: 0.06 lb.

Notes:

1. Input: Barrier type. Three No. 6-32 B.H. screws (0.375” centers). Max torque: 6 in-lbs. (0.67 N-m).

2. Control connectors: (J1 and J2) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III Series). Connector kit includes mating

connector and 10 pins, Astec part #70-841-004.

3. Chassis material: aluminum with chemical lm coating (conductive).

4. All dimensions are in millimeters and inches, and are typical.

5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.150” (3.8 mm). Max. torque: 5 in-lbs.

6. Output module connections: All single O/P modules are M4 x 8 mm screws. Max. torque: 10 in-lbs.

Dual O/P module is M3 x 8 mm screws. Max. torque: 5 in-lbs.

Triple O/P module is .045” square pins on .156” centers. Mates with Moelx 09-50-8063 or equivalent.

MP Series Data Sheet

MP Series

MP8 (800/1000 Watts Max) 7-Inch Case Size: MP8: 2.5” x 7” x 10” (63.5 mm x 177.8 mm x 254 mm)

Weight: MP8 Case: 4.1 lbs. • 36 W Triple: 0.5 lb. • 210 W Single: 0.6 lb. • 360 W Single: 1.0 lb.

• 600 W Single: 2.6 lbs. • 144 W Dual: 0.6 lb.

Notes:

1. Input: Barrier type. Three No. 6-32 B.H. screws (0.375” centers). Max torque: 6 in-lbs. (0.67 N-m).

connector and 10 pins, Astec part #70-841-004.

3. Chassis material: aluminum with chemical lm coating (conductive).

4. All dimensions are in millimeters and inches, and are typical.

5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.150” (3.8 mm). Max. torque: 5 in-lbs.

6. Output module connections: All single O/P modules are M4 x 8 mm screws. Max. torque: 10 in-lbs.

Dual O/P module is M3 x 8 mm screws. Max. torque: 5 in-lbs.

Triple O/P Module is .045” square pins on .156 centers. Mates with Moelx 09-50-8063 or equivalent.

19.05

0.75

171.45

6.75

29.05

1.1

171.45

6.75

12.70

0.5

M4 MOUNTING HOLES

#8-32 MOUNTING HOLES

MARKED "A" (4X)

"A"

"A" "A"

"A"

"B"

MARKED "B" (4X)

"B"

152.40

6.0

254

10.0

Standard Airow

59.5

2.34

14.7

0.58

31.8

1.25

63.5

2.5

60.5

2.38

14.0

0.55

177.8

7.0

M4 MOUNTING HOLES (4X)

171.45

6.75

19.05

0.7

38.10

1.5 35.0

1.38

12.70

0.5 254

10.0

63.5

2.5

MP Series Data Sheet

WORLDWIDE OFFICES

Americas

2900 S.Diablo Way

Tempe, AZ 85282

USA

+1 888 412 7832

Europe (UK)

Waterfront Business Park

Merry Hill, Dudley

West Midlands, DY5 1LX

United Kingdom

+44 (0) 1384 842 211

Asia (HK)

14/F, Lu Plaza

2 Wing Yip Street

Kwun Tong, Kowloon

Hong Kong

+852 2176 3333

For more information: www.artesyn.com/power

For support: productsupport.ep@artesyn.com

While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn

Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use

of this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn

Embedded Technologies logo are trademarks and service marks of Artesyn Technologies, Inc. All other names

and logos referred to are trade names, trademarks, or registered trademarks of their respective owners.

www.artesyn.com

MP DS Rev. 03.10.14

MP Series

MP1 (1000/1200 Watts Max)

8-Inch Case Size:

MP1: 2.5” x 8” x 11”

(63.5 mm x 203.2 mm x 279.4 mm)

Weight:

MP1 Case: 5.0 lbs.

• 36 W Triple: 0.5 lb.

• 210 W Single: 0.6 lb.

• 360 W Single: 1.0 lb.

• 600 W Single: 2.0 lbs.

• 144 W Dual: 0.6 lb.

Notes:

1. Input: Barrier type. Three No. 6-32 B.H. screws (0.375” centers).

Max torque: 6 in-lbs (0.67 N-m).

2. Control connectors: (J1 and J2) 10 position housing, gold plated

contacts. Mates with Molex 90142-0010 housing with 90119-2110

crimp contacts (Molex C - Grid III Series). Connector kit includes mating

connector and 10 pins, Astec part #70- 841-004.

3. Chassis material: aluminum with chemical lm coating (conductive).

4. All dimensions are in millimeters and inches, and are typical.

5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting

holes. Max. penetration is 0.150” (3.8 mm). Max. torque: 5 in-lbs.

6. Output module connections: All single O/P modules are M4 x 8 mm

screws. Max. torque: 10 in-lbs.

Dual O/P module is M3 x 8 mm screws. Max. torque: 5 in-lbs.

Triple O/P module is .045” square pins on .156 centers. Mates with

Molex 09-50-8063 or equivalent.

171.45

6.750

171.45

6.750

19.05

.750

177.80

7.000

29.05

1.144 12.70

.500

M4 MTG

HOLES

4 PL

MARKED “B”

STD AIR FLOW

#8-32 MTG HOLES

4 PL

MARKED “A”

BOTTOM MOUNTING SURFACE

203.2

8.00

31.8

1.25

76.2

3.00

69.9

2.75

14.0

.55

14.7

.58

171.45

6.750

38.10

1.500

12.70

.500 279.4

11.00

35.0

1.38

19.05

.750

16.50

6.50

63.5

2.50

MOUNTING HOLES - DIMENSIONS

IDENTICAL ON BOTH SIDES

M4 MTG HOLES 4 PL