1. General description
The 74HC4066-Q100; 74HCT4066-Q100 is a quad single pole, single throw analog
switch. Each switch features two input/output terminals (nY and nZ) and an active HIGH
enable input (nE). When nE is LOW, the analog switch is turned off. Inputs include clamp
diodes. This enables the use of current limiting resistors to interface inputs to voltages in
excess of VCC.
This product has been qualified to the Automotive Electronics Council (AEC) standard
Q100 (Grade 1) and is suitable for use in automotive applications.
2. Features and benefits
Automotive product qualification in accordance with AEC-Q100 (Grade 1)
Specified from 40 C to +85 C and from 40 C to +125 C
Input levels nE inputs:
For 74HC4066-Q100: CMOS level
For 74HCT4066-Q100: TTL level
Low ON resistance:
50 (typical) at VCC = 4.5 V
45 (typical) at VCC = 6.0 V
35 (typical) at VCC = 9.0 V
Specified in compliance with JEDEC standard no. 7A
ESD protection:
MIL-STD-883, method 3015 exceeds 2000 V
HBM JESD22-A114F exceeds 2000 V
MM JESD22-A115-A exceeds 200 V (C = 200 pF, R = 0 )
Multiple package options
74HC4066-Q100;
74HCT4066-Q100
Quad single-pole single-throw analog switch
Rev. 3 — 16 December 2013 Product data sheet
© Nexperia B.V. 2017. All rights reserved
74HC_HCT4066_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 3 — 16 December 2013 2 of 23
Nexperia 74HC4066-Q100; 74HCT4066-Q100
Quad single-pole single-throw analog switch
3. Ordering information
4. Functional diagram
Table 1. Ordering information
Type number Package
Temperature range Name Description Version
74HC4066D-Q100 40 C to +125 C SO14 plastic small outline package; 14 leads; body width
3.9 mm SOT108-1
74HCT4066D-Q100
74HC4066PW-Q100 40 C to +125 C TSSOP14 plastic thin shrink small outline package; 14 leads;
body width 4.4 mm SOT402-1
74HCT4066PW-Q100
74HC4066BQ-Q100 40 C to +125 C DHVQFN14 plastic dual in-line compatible thermal enhanced
very thin quad flat package; no leads; 14 terminals;
body 2.5 30.85 mm
SOT762-1
74HCT4066BQ-Q100
Fig 1. Logic symbol Fig 2. IEC logic symbol
001aad269
1Y 1Z
12
2Y 2Z
43
1E
13
3Y 3Z
89
4Y 4Z
11 10
3E
6
4E
12
2E
5
001aad270
12
13 #
43
5#
89
6#
11 10
(a)
12 #
12
13 1
X1
1
X1
1
X1
1
1
1
1
1
X1
#
43
5#
89
6#
11 10
(b)
12 #
Fig 3. Schematic diagram (one sw itc h)
001aad271
GND nZ
nE
nY
VCC VCC
© Nexperia B.V. 2017. All rights reserved
74HC_HCT4066_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 3 — 16 December 2013 3 of 23
Nexperia 74HC4066-Q100; 74HCT4066-Q100
Quad single-pole single-throw analog switch
5. Pinning information
5.1 Pinning
5.2 Pin description
(1) This is not a supply pin. The substrate is attached to this
pad using conductive die attach material. There is no
electrical or mechanical requirement to solder this pad.
However, if it is soldered, the solder land should remain
floating or be connected to VCC.
Fig 4. Pin configuration for SO14 and TSSOP14 Fig 5. Pin configuration for DHVQFN14
+&4
+&74
< 9&&
= (
=(
<<
(=
(=
*1' <
DDD





DDD
+&4
+&74
7UDQVSDUHQWWRSYLHZ
( =
( =
< <
= (
= (
*1'
<
<
9
&&





WHUPLQDO
LQGH[DUHD
9
&&
Table 2. Pin description
Symbol Pin Description
1Z, 2Z, 3Z, 4Z 2, 3, 9, 10 independent input or output
1Y, 2Y, 3Y, 4Y 1, 4, 8, 11 independent input or output
GND 7 ground (0 V)
1E, 2E, 3E, 4E 13, 5, 6, 12 enable input (active HIGH)
VCC 14 supply voltage
© Nexperia B.V. 2017. All rights reserved
74HC_HCT4066_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 3 — 16 December 2013 4 of 23
Nexperia 74HC4066-Q100; 74HCT4066-Q100
Quad single-pole single-throw analog switch
6. Functional description
[1] H = HIGH voltage level;
L = LOW voltage level.
7. Limiting values
[1] To avoid drawing VCC current out of terminal Z, when switch current flows in terminals Yn, the voltage drop across the bidirectional
switch must not exceed 0.4 V. If the switch current flows into terminal Z, no VCC current will flow out of terminals Yn. In this case there is
no limit for the voltage drop across the switch, but the voltages at Yn and Z may not exceed VCC or GND.
[2] For SO14 packages: Ptot derates linearly with 8 mW/K above 70 C.
For TSSOP14 packages: Ptot derates linearly with 5.5 mW/K above 60 C.
For DHVQFN14 packages: Ptot derates linearly with 4.5 mW/K above 60 C.
8. Recommended operating conditions
Table 3. Function table[1]
Input nE Switch
LOFF
HON
Table 4. Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).
Symbol Parameter Conditions Min Max Unit
VCC supply voltage 0.5 +11.0 V
IIK input clamping current VI<0.5 V or VI>V
CC +0.5V - 20 mA
ISK switch clamping current VSW <0.5 V or VSW >V
CC +0.5V - 20 mA
ISW switch current VSW =0.5 V to VCC +0.5V [1] -25 mA
ICC supply current - 50 mA
IGND ground current - 50 mA
Tstg storage temperature 65 +150 C
Ptot total power dissipation Tamb = 40 C to +125 C[2] -500
P power dissipation per switch - 100 mW
Table 5. Recommended operating con ditions
Symbol Parameter Conditions 74HC4066-Q100 74HCT4066-Q100 Unit
Min Typ Max Min Typ Max
VCC supply voltage 2.0 5.0 10.0 4.5 5.0 5.5 V
VIinput voltage GND - VCC GND - VCC V
VSW switch voltage GND - VCC GND - VCC V
Tamb ambient temperature 40 +25 +125 40 +25 +125 C
t/V input transition rise
and fall rate VCC = 2.0 V - - 625 - - - ns/V
VCC = 4.5 V - 1.67 139 - 1.67 1 39 ns/V
VCC = 6.0 V - - 83 - - - ns/V
VCC = 10.0 V - - 35 - - - ns/V
© Nexperia B.V. 2017. All rights reserved
74HC_HCT4066_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 3 — 16 December 2013 5 of 23
Nexperia 74HC4066-Q100; 74HCT4066-Q100
Quad single-pole single-throw analog switch
9. Static characteristics
[1] Typical values are measured at Tamb = 25 C.
[2] At supply voltages (VCC GND) approaching 2 V, the analog switch ON resistance becomes extremely non-linear. Therefore it is
recommended that these devices be used to transmit digital signals only, when using these supply voltages.
Table 6. RON resistance per switch for types 74HC4066-Q100 and 74HCT4066-Q100
VI = VIH or VIL; for test circuit see Figure 6.
Vis is the input voltage at a Yn or Z terminal, whichever is assigned as an input.
Vos is the output voltage at a Yn or Z terminal, whichever is assigned as an output.
For 74HC4066-Q100: VCC
GND = 2.0 V, 4.5 V, 6.0 V and 9.0 V.
For 74HCT4066-Q100: VCC
GND = 4.5 V.
Symbol Parameter Conditions 40 C to +85 C40 C to +125
CUnit
Min Typ[1] Max Min Max
RON(peak) ON resistance (peak) Vis = VCC to GND
VCC = 2.0 V; ISW = 100 A[2] -----
VCC = 4.5 V; ISW = 1000 A - 54 - 118 142
VCC = 6.0 V; ISW = 1000 A - 42 - 105 126
VCC = 9.0 V; ISW = 1000 A - 32 - 88 105
RON(rail) ON resistance (rail) Vis = GND
VCC = 2.0 V; ISW = 100 A[2] -80---
VCC = 4.5 V; ISW = 1000 A - 35 - 95 115
VCC = 6.0 V; ISW = 1000 A - 27 - 82 100
VCC = 9.0 V; ISW = 1000 A-20-7085
Vis = VCC
VCC = 2.0 V; ISW = 100 A[2] -100---
VCC = 4.5 V; ISW = 1000 A - 42 - 106 128
VCC = 6.0 V; ISW = 1000 A - 35 - 94 113
VCC = 9.0 V; ISW = 1000 A-20-7895
RON ON resistance
mismatch between
channels
Vis = VCC to GND
VCC = 2.0 V [2] -----
VCC = 4.5V -5---
VCC = 6.0V -4---
VCC = 9.0V -3---
© Nexperia B.V. 2017. All rights reserved
74HC_HCT4066_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 3 — 16 December 2013 6 of 23
Nexperia 74HC4066-Q100; 74HCT4066-Q100
Quad single-pole single-throw analog switch
Vis = 0 V to VCC Vis = 0 V to VCC
Fig 6. Test circuit for measuring RON Fig 7. Typical RON as a function of input voltage Vis
aaa-003458
Vis ISW
VIH
VCC
GND
nZnY
nE
VSW
Vis (V)
0 9.07.23.6 5.41.8
aaa-003459
30
40
20
50
60
RON
(Ω)
10
VCC = 4.5 V
6 V
9 V
RON VSW
ISW
----------
=
Table 7. Static characteristics 74HC4066-Q100
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Vis is the input voltage at a Yn or Z terminal, whichever is assigned as an input.
Vos is the output voltage at a Yn or Z terminal, whichever is assigned as an output.
Symbol Parameter Conditions Min Typ[1] Max Unit
Tamb = 40 C to +85 C
VIH HIGH-level input voltage VCC = 2.0 V 1.5 1.2 - V
VCC = 4.5 V 3.15 2.4 - V
VCC = 6.0 V 4.2 3.2 - V
VCC = 9.0 V 6.3 4.7 - V
VIL LOW-level input voltage VCC = 2.0 V - 0.8 0.5 V
VCC = 4.5 V - 2.1 1.35 V
VCC = 6.0 V - 2.8 1.80 V
VCC = 9.0 V - 4.3 2.70 V
IIinput leakage current VI = VCC or GND
VCC = 6.0 V - - 1.0 A
VCC = 10.0 V - - 2.0 A
IS(OFF) OFF-state leakage current VCC = 10.0 V; VI = VIH or VIL;
VSW=V
CC GND; see Figure 8
per channel - - 1.0 A
IS(ON) ON-state leakage current VCC = 10.0 V; VI = VIH or VIL;
VSW=V
CC GND; see Figure 9 --1.0 A
© Nexperia B.V. 2017. All rights reserved
74HC_HCT4066_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 3 — 16 December 2013 7 of 23
Nexperia 74HC4066-Q100; 74HCT4066-Q100
Quad single-pole single-throw analog switch
[1] Typical values are measured at Tamb = 25 C.
ICC supply current VI = VCC or GND; Vis = GND or VCC;
Vos =V
CC or GND
VCC = 6.0 V - - 20.0 A
VCC = 10.0 V - - 40.0 A
CIinput capacitance - 3.5 - pF
Csw switch capacitance - 8 - pF
Tamb = 40 C to +125 C
VIH HIGH-level input voltage VCC = 2.0 V 1.5 - - V
VCC = 4.5 V 3.15 - - V
VCC = 6.0 V 4.2 - - V
VCC = 9.0 V 6.3 - - V
VIL LOW-level input voltage VCC = 2.0 V - - 0.50 V
VCC = 4.5 V - - 1.35 V
VCC = 6.0 V - - 1.80 V
VCC = 9.0 V - - 2.70 V
IIinput leakage current VI = VCC or GND
VCC = 6.0 V - - 1.0 A
VCC = 10.0 V - - 2.0 A
IS(OFF) OFF-state leakage current VCC = 10.0 V; VI = VIH or VIL;
VSW=V
CC GND; see Figure 8
per channel - - 1.0 A
IS(ON) ON-state leakage current VCC = 10.0 V; VI = VIH or VIL;
VSW=V
CC GND; see Figure 9 --1.0 A
ICC supply current VI = VCC or GND; Vis = GND or VCC;
Vos =V
CC or GND
VCC = 6.0 V - - 40 A
VCC = 10.0 V - - 80 A
Table 7. Static characteristics 74HC4066-Q100 …continued
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Vis is the input voltage at a Yn or Z terminal, whichever is assigned as an input.
Vos is the output voltage at a Yn or Z terminal, whichever is assigned as an output.
Symbol Parameter Conditions Min Typ[1] Max Unit
Table 8. Static characteristics 74HCT4066-Q100
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Vis is the input voltage at a Yn or Z terminal, whichever is assigned as an input.
Vos is the output voltage at a Yn or Z terminal, whichever is assigned as an output.
Symbol Parameter Conditions Min Typ[1] Max Unit
Tamb = 40 C to +85 C
VIH HIGH-level input voltage VCC = 4.5 V to 5.5 V 2.0 1.6 - V
VIL LOW-level input voltage VCC = 4.5 V to 5.5 V - 1.2 0.8 V
IIinput leakage current VI = VCC or GND; VCC = 5.5 V - - 1.0 A
© Nexperia B.V. 2017. All rights reserved
74HC_HCT4066_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 3 — 16 December 2013 8 of 23
Nexperia 74HC4066-Q100; 74HCT4066-Q100
Quad single-pole single-throw analog switch
[1] Typical values are measured at Tamb = 25 C.
IS(OFF) OFF-state leakage current VCC = 5.5 V; VI = VIH or VIL;
VSW=V
CC GND; see Figure 8
per channel - - 1.0 A
IS(ON) ON-state leakage current VCC = 5.5 V; VI = VIH or VIL;
VSW=V
CC GND; see Figure 9 --1.0 A
ICC supply current VI = VCC or GND; Vis = GND or VCC;
Vos =V
CC or GND; VCC = 4.5 V to 5.5 V - - 20.0 A
ICC additional supply current per input pin; VI = VCC 2.1 V; other inputs
at VCC or GND; VCC = 4.5 V to 5.5 V - 100 450 A
CIinput capacitance - 3.5 - pF
Csw switch capacitance - 8 - pF
Tamb = 40 C to +125 C
VIH HIGH-level input voltage VCC = 4.5 V to 5.5 V 2.0 - - V
VIL LOW-level input voltage VCC = 4.5 V to 5.5 V - - 0.8 V
IIinput leakage current VI = VCC or GND; VCC = 5.5 V - - 1.0 A
IS(OFF) OFF-state leakage current VCC = 5.5 V; VI = VIH or VIL;
VSW=V
CC GND; see Figure 8
per channel - - 1.0 A
IS(ON) ON-state leakage current VCC = 5.5 V; VI = VIH or VIL;
VSW=V
CC GND; see Figure 9 --1.0 A
ICC supply current VI = VCC or GND; Vis = GND or VCC;
Vos =V
CC or GND; VCC = 4.5 V to 5.5 V --40A
ICC additional supply current per input pin; VI = VCC 2.1 V; other input s
at VCC or GND; VCC = 4.5 V to 5.5 V - - 490 A
Table 8. Static characteristics 74HCT4066-Q100 …continued
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Vis is the input voltage at a Yn or Z terminal, whichever is assigned as an input.
Vos is the output voltage at a Yn or Z terminal, whichever is assigned as an output.
Symbol Parameter Conditions Min Typ[1] Max Unit
Vis = VCC and Vos = GND
Vis = GND and Vos = VCC
Vis = VCC and Vos = open
Vis = GND and Vos = open
Fig 8. Test circuit for measuring OFF-state leakage
current Fig 9. Test circuit for measuring ON-state leakage
current
I
SW
I
SW
aaa-003456
V
IL
Z
V
CC
Yn
E
Vos
Vis
GND
ISW
aaa-003457
VIH
ZYn
E
Vos
Vis
GND
VCC
© Nexperia B.V. 2017. All rights reserved
74HC_HCT4066_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 3 — 16 December 2013 9 of 23
Nexperia 74HC4066-Q100; 74HCT4066-Q100
Quad single-pole single-throw analog switch
10. Dynamic characteristics
[1] Typical values are measured at Tamb = 25 C.
[2] tpd is the same as tPHL and tPLH.
[3] ton is the same as tPHZ and tPLZ.
[4] toff is the same as tPZH and tPZL.
[5] CPD is used to determine the dynamic power dissipation (PD in W).
PD = CPD VCC2fi+{(CL+C
sw) VCC2 fo} where:
fi = input frequency in MHz;
fo = output frequency in MHz;
{(CL+C
sw) VCC2 fo} = sum of outputs;
CL = output load capacitance in pF;
Csw = switch capacitance in pF;
VCC = supply voltage in V.
Table 9. Dynamic characteristics 74HC4066-Q100
GND = 0 V; tr = tf = 6 ns; CL = 50 pF unless specified otherwise; for test circuit see Figure 12.
Vis is the input voltage at a Yn or Z terminal, whichever is assigned as an input.
Vos is the output voltage at a Yn or Z terminal, whichever is assigned as an output.
Symbol Parameter Conditions 40 C to +85 C40 C to +125 CUnit
Min Typ[1] Max Min Max
tpd propagation delay nY to nZ or nZ to nY; RL= ;
see Figure 10 [2]
VCC = 2.0 V - 8 75 - 90 ns
VCC = 4.5 V - 3 15 - 18 ns
VCC = 6.0 V - 2 13 - 15 ns
VCC = 9.0 V - 2 10 - 12 ns
toff turn-off time nE to nY or nZ; see Figure 11 [4]
VCC = 2.0 V - 44 190 - 225 ns
VCC = 4.5 V - 16 38 - 45 ns
VCC = 5.0 V; CL = 15 pF - 13 - - - ns
VCC = 6.0 V - 13 33 - 38 ns
VCC = 9.0 V - 16 26 - 30 ns
ton turn-on time nE to nY or nZ; see Figure 11 [3]
VCC = 2.0 V - 36 125 - 150 ns
VCC = 4.5 V - 13 25 - 30 ns
VCC = 5.0 V; CL = 15 pF - 11 - - - ns
VCC = 6.0 V - 10 21 - 26 ns
VCC = 9.0 V - 8 16 - 20 ns
CPD power dissipation
capacitance per switch; VI = GND to VCC [5] 11 - - - pF
© Nexperia B.V. 2017. All rights reserved
74HC_HCT4066_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 3 — 16 December 2013 10 of 23
Nexperia 74HC4066-Q100; 74HCT4066-Q100
Quad single-pole single-throw analog switch
[1] Typical values are measured at Tamb = 25 C.
[2] tpd is the same as tPHL and tPLH.
[3] ton is the same as tPHZ and tPLZ.
[4] toff is the same as tPZH and tPZL.
[5] CPD is used to determine the dynamic power dissipation (PD in W).
PD = CPD VCC2fi+{(CL+C
sw) VCC2 fo} where:
fi = input frequency in MHz;
fo = output frequency in MHz;
{(CL+C
sw) VCC2 fo} = sum of outputs;
CL = output load capacitance in pF;
Csw = switch capacitance in pF;
VCC = supply voltage in V.
Table 10. Dynamic characteristics 74HCT4066-Q100
GND = 0 V; tr = tf = 6 ns; CL = 50 pF unless specified otherwise; for test circuit see Figure 12.
Vis is the input voltage at a Yn or Z terminal, whichever is assigned as an input.
Vos is the output voltage at a Yn or Z terminal, whichever is assigned as an output.
Symbol Parameter Conditions 40 C to +85 C40 C to +125 CUnit
Min Typ[1] Max Min Max
tpd propagation
delay nY to nZ or nZ to nY; RL= ;
see Figure 10 [2]
VCC = 4.5 V - 3 15 - 18 ns
toff turn-off time nE to nY or nZ; see Figure 11 [4]
VCC = 4.5 V - 20 44 - 53 ns
VCC = 5.0 V; CL = 15 pF - 16 - - - ns
ton turn-on time nE to nY or nZ; see Figure 11 [3]
VCC = 4.5 V - 12 30 - 36 ns
VCC = 5.0 V; CL = 15 pF - 12 - - - ns
CPD power dissipation
capacitance per switch;
VI=GNDto(V
CC 1.5 V) [5] -12- - -pF
© Nexperia B.V. 2017. All rights reserved
74HC_HCT4066_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 3 — 16 December 2013 11 of 23
Nexperia 74HC4066-Q100; 74HCT4066-Q100
Quad single-pole single-throw analog switch
11. Waveforms
Fig 10. Input (Vis) to output (Vos) p ropagation delays
Measurement points are shown in Table 11.
Fig 11. Turn-on and turn-off times
aaa-003460
t
PLZ
t
PHZ
switch OFF switch ON
switch ON
V
os
output
V
os
output
E input V
M
V
I
0 V
90 %
10 %
t
PZL
t
PZH
50 %
50 %
Table 11. Measurement points
Type VIVM
74HC4066-Q100 VCC 0.5VCC
74HCT4066-Q100 3.0 V 1.3 V
© Nexperia B.V. 2017. All rights reserved
74HC_HCT4066_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 3 — 16 December 2013 12 of 23
Nexperia 74HC4066-Q100; 74HCT4066-Q100
Quad single-pole single-throw analog switch
[1] For 74HCT4066-Q100: maximum input voltage VI = 3.0 V.
Test data is given in Table 12.
Definitions test circuit:
RT = Termination resistance should be equal to output impedance Zo of the pulse generator.
CL = Load capacitance including jig and probe capacitance.
RL = Load resistor.
S1 = Test selection switch.
Fig 12. Load circuitry for measuring switching times
V
M
V
M
t
W
t
W
10 %
90 %
0 V
V
I
V
I
negative
pulse
positive
pulse
0 V
V
M
V
M
90 %
10 %
t
f
t
r
t
r
t
f
001aag732
V
CC
V
CC
open
GND
V
I
V
os
DUT
CL
RT
RLS1
PULSE
GENERATOR
V
is
Table 12. Test data
Test Input Output S1 position
Control E Switch Yn (Z) tr, tfSwitch Z (Yn)
VI[1] Vis CLRL
tPHL, tPLH GND GND to VCC 6 ns 50 pF - open
tPHZ, tPZH GND to VCC VCC 6ns 50pF, 15pF 1kGND
tPLZ, tPZL GND to VCC GND 6 ns 50 pF, 15 pF 1 kVCC
© Nexperia B.V. 2017. All rights reserved
74HC_HCT4066_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 3 — 16 December 2013 13 of 23
Nexperia 74HC4066-Q100; 74HCT4066-Q100
Quad single-pole single-throw analog switch
12. Additional dynamic characteristics
[1] Adjust input voltage Vis to 0 dBm level (0 dBm = 1 mW into 600 ).
[2] Adjust input voltage Vis to 0 dBm level at Vos for fi = 1 MHz (0 dBm = 1 mW into 50 ). After set-up, fi is increased to obtain a reading of
3dB at V
os.
Table 13. Additional dynamic characteristics
Recommended conditio ns and typical values; GND = 0 V; Tamb = 25
C.
Vis is the input voltage at a Yn or Z terminal, whichever is assigned as an input.
Vos is the output voltage at a Yn or Z terminal, whichever is assigned as an output.
Symbol Parameter Conditions Min Typ Max Unit
THD total harmonic distortion fi= 1 kHz; RL= 10 k; CL=50pF;
see Figure 13 %
VCC = 4.5 V; VI= 4.0 V (p-p) - 0.04 - %
VCC = 9.0 V; VI= 8.0 V (p-p) - 0.02 - %
fi=10kHz; R
L= 10 k; CL=50pF;
see Figure 13
VCC = 4.5 V; VI= 4.0 V (p-p) - 0.12 - %
VCC = 9.0 V; VI= 8.0 V (p-p) - 0.06 - %
f(3dB) 3 dB frequency response RL= 50 ; CL=10pF; seeFigure 15 [2]
VCC = 4.5 V - 180 - MHz
VCC = 9.0 V - 200 - MHz
iso isolation (OFF-state) RL= 600 ; CL=50pF; f
i= 1 MHz;
see Figure 14 [1]
VCC = 4.5 V - 50 - dB
VCC = 9.0 V - 50 - dB
Vct crosstalk voltage between digital input and switch (peak to
peak value); RL= 600 ; CL=50pF;
fi= 1 MHz; see Figure 16
VCC = 4.5 V - 110 - mV
VCC = 9.0 V - 220 - mV
Xtalk crosstalk between switches; RL= 600 ; CL=50pF;
fi= 1 MHz; see Figure 17 [1]
VCC = 4.5 V - 60 - dB
VCC = 9.0 V - 60 - dB
Fig 13. Test circuit for measuring total harmonic distortion
10 μF
2RL
2RLCL
fi
VIH
VO
VCC VCC
nE
D
nY/nZ nZ/nY
001aaj468
© Nexperia B.V. 2017. All rights reserved
74HC_HCT4066_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 3 — 16 December 2013 14 of 23
Nexperia 74HC4066-Q100; 74HCT4066-Q100
Quad single-pole single-throw analog switch
a. Isolation (OFF-state)
b. Test circuit
VCC = 4.5 V; GND = 0 V; RL = 600 ; Rsource = 1 k.
Fig 14. Isolation (OFF -s tate) as a function of frequency
mna082
−60
−40
−80
−20
0
(dB)
−10010 fi (kHz)
105106
104
102103
0.1 μF
2RL
2RL
CL
fi
VIL
VO
VCC VCC
nE
dB
nY/nZ nZ/nY
001aaj470
© Nexperia B.V. 2017. All rights reserved
74HC_HCT4066_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 3 — 16 December 2013 15 of 23
Nexperia 74HC4066-Q100; 74HCT4066-Q100
Quad single-pole single-throw analog switch
a. Typical 3 dB frequency response
b. Test circuit
VCC = 4.5 V; GND = 0 V; RL = 50 ; Rsource = 1 k.
Fig 15. 3 d B frequency response
mna083
5
(dB)
−510 fi (kHz)
105106
104
102103
0
0.1 μF
2RL
2RLCL
fi
VIH
VO
VCC VCC
nE
dB
nY/nZ nZ/nY
001aaj469
© Nexperia B.V. 2017. All rights reserved
74HC_HCT4066_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 3 — 16 December 2013 16 of 23
Nexperia 74HC4066-Q100; 74HCT4066-Q100
Quad single-pole single-throw analog switch
a. Circuit
b. Crosstalk voltage
Fig 16. Test circuit for measuring crosstalk voltage (between the digital input and the switch)
DUT
mnb011
2RL
2RL
2RL
2RLnZ/nYnY/nZ
CLoscilloscope
VCC nE VCC
VCC
GND
GND
mnb012
V(p−p)
Fig 17. Test circu it for measu ring crosstalk (between the switches)
001aai846
VIH
VCC
1Z or 1Y1Y or 1Z
CHANNEL
ON
1E
fi
2RL
RL
0.1 μF
CLV
VIL
VCC VCC
2Z or 2Y2Y or 2Z
CHANNEL
OFF
2E
2RL
2RL2RL
2RL
2RL
CLV
VO1
VO2
© Nexperia B.V. 2017. All rights reserved
74HC_HCT4066_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 3 — 16 December 2013 17 of 23
Nexperia 74HC4066-Q100; 74HCT4066-Q100
Quad single-pole single-throw analog switch
13. Package outline
Fig 18. Package outline SOT108-1 (SO14)
UNIT A
max. A1A2A3bpcD
(1) E(1) (1)
eH
ELL
pQZywv θ
REFERENCES
OUTLINE
VERSION EUROPEAN
PROJECTION ISSUE DATE
IEC JEDEC JEITA
mm
inches
1.75 0.25
0.10 1.45
1.25 0.25 0.49
0.36 0.25
0.19 8.75
8.55 4.0
3.8 1.27 6.2
5.8 0.7
0.6 0.7
0.3 8
0
o
o
0.25 0.1
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
Note
1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included.
1.0
0.4
SOT108-1
X
wM
θ
A
A1
A2
bp
D
HE
Lp
Q
detail X
E
Z
e
c
L
vMA
(A )
3
A
7
8
1
14
y
076E06 MS-012
pin 1 index
0.069 0.010
0.004 0.057
0.049 0.01 0.019
0.014 0.0100
0.0075 0.35
0.34 0.16
0.15 0.05
1.05
0.041
0.244
0.228 0.028
0.024 0.028
0.012
0.01
0.25
0.01 0.004
0.039
0.016
99-12-27
03-02-19
0 2.5 5 mm
scale
SO14: plastic small outline package; 14 leads; body width 3.9 mm SOT108-1
© Nexperia B.V. 2017. All rights reserved
74HC_HCT4066_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 3 — 16 December 2013 18 of 23
Nexperia 74HC4066-Q100; 74HCT4066-Q100
Quad single-pole single-throw analog switch
Fig 19. Package outline SOT402-1 (TSSOP14)
UNIT A1A2A3bpcD
(1) E(2) (1)
eH
ELL
pQZywv θ
REFERENCES
OUTLINE
VERSION EUROPEAN
PROJECTION ISSUE DATE
IEC JEDEC JEITA
mm 0.15
0.05 0.95
0.80 0.30
0.19 0.2
0.1 5.1
4.9 4.5
4.3 0.65 6.6
6.2 0.4
0.3 0.72
0.38 8
0
o
o
0.13 0.10.21
DIMENSIONS (mm are the original dimensions)
Notes
1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.
2. Plastic interlead protrusions of 0.25 mm maximum per side are not included.
0.75
0.50
SOT402-1 MO-153 99-12-27
03-02-18
wM
bp
D
Z
e
0.25
17
14 8
θ
A
A1
A2
Lp
Q
detail X
L
(A )
3
HE
E
c
vMA
X
A
y
0 2.5 5 mm
scale
TSSOP14: plastic thin shrink small outline package; 14 leads; body width 4.4 mm SOT402-1
A
max.
1.1
pin 1 index
© Nexperia B.V. 2017. All rights reserved
74HC_HCT4066_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 3 — 16 December 2013 19 of 23
Nexperia 74HC4066-Q100; 74HCT4066-Q100
Quad single-pole single-throw analog switch
Fig 20. Package outline SOT762-1 (DHVQFN14)
terminal 1
index area
0.51
A1Eh
b
UNIT ye
0.2
c
REFERENCES
OUTLINE
VERSION EUROPEAN
PROJECTION ISSUE DATE
IEC JEDEC JEITA
mm 3.1
2.9
Dh
1.65
1.35
y1
2.6
2.4 1.15
0.85
e1
2
0.30
0.18
0.05
0.00 0.05 0.1
DIMENSIONS (mm are the original dimensions)
SOT762-1 MO-241 - - -- - -
0.5
0.3
L
0.1
v
0.05
w
0 2.5 5 mm
scale
SOT762-1
DHVQFN14: plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads;
14 terminals; body 2.5 x 3 x 0.85 mm
A(1)
max.
AA1c
detail X
y
y1C
e
L
Eh
Dh
e
e1
b
26
13 9
8
7
1
14
X
D
E
C
BA
02-10-17
03-01-27
terminal 1
index area
AC
CB
vM
wM
E(1)
Note
1. Plastic or metal protrusions of 0.075 mm maximum per side are not included.
D(1)
© Nexperia B.V. 2017. All rights reserved
74HC_HCT4066_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 3 — 16 December 2013 20 of 23
Nexperia 74HC4066-Q100; 74HCT4066-Q100
Quad single-pole single-throw analog switch
14. Abbreviations
15. Revision history
Table 14. Abbreviations
Acronym Description
CMOS Complementary Metal Oxide Semiconductor
ESD ElectroStatic Discharge
HBM Human Body Model
MM Machine Model
CDM Charge-Device Model
MIL Military
Table 15. Revision history
Document ID Release date Data sheet status Change
notice Supersedes
74HC_HCT4066_Q100 v.3 20131216 Product data sheet - 74HC_HCT4066_Q100 v.2
Modifications: •Features and benefits updated (errata).
74HC_HCT4066_Q100 v.2 20130404 Product data sheet - 74HC_HCT4066_Q100 v.1
Modifications: •Descriptive title corrected (errata).
•New general description (errata).
74HC_HCT4066_Q100 v.1 20120712 Product data sheet - -
© Nexperia B.V. 2017. All rights reserved
74HC_HCT4066_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 3 — 16 December 2013 21 of 23
Nexperia 74HC4066-Q100; 74HCT4066-Q100
Quad single-pole single-throw analog switch
16. Legal information
16.1 Data sheet status
[1] Please consult the most recently issued document before initiating or completing a design.
[2] The term ‘short data sheet’ is explained in section “Definitions”.
[3] The product status of de vice(s) descr ibed in th is docume nt may have cha nged since this docume nt was publis hed and ma y dif fer in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nexperia.com.
16.2 Definitions
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. Nexperia does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liab ility for the consequences of
use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and tit le. A short data sh eet is intended
for quick reference only and shou ld not be rel ied u pon to cont ain det ailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local Nexperia sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall pre vail.
Product specificatio n — The information and data provided in a Product
data sheet shall define the specification of the product as agreed between
Nexperia and its customer, unless Nexperia and
customer have explicitly agreed otherwise in writing. In no event however,
shall an agreement be valid in which the Nexperia product is
deemed to off er functions and qualities beyond tho se described in the
Product data sheet.
16.3 Disclaimers
Limited warr a nty and liability — Information in this document is believed to
be accurate and reliable. However, Nexperia does not give any
representations or warranties, expressed or implied, as to the accuracy or
completeness of such information and shall have no liability for the
consequences of use of such information. Nexperia takes no
responsibility for the content in this document if provided by an inf ormation
source outside of Nexperia.
In no event shall Nexperia be liable for any indirect, incidental,
punitive, special or consequ ential damages (including - wit hout limitatio n - lost
profits, lost savings, business interruption, costs related to the removal or
replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
Notwithstanding any damages that customer might incur for any reason
whatsoever, Nexperia’s aggregate and cumulative liability towards
customer for the products described herein shall be limited in accordance
with the Terms and conditions of commercial sale of Nexperia.
Right to make changes — Nexperia reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all informa tion supplied prior
to the publication hereof .
Suitability for use in automotive applications — This Nexperia
product has been qualified for use in automotive
applications. Unless ot herwise agreed in writing, the product is not designed,
authorized or warranted to be suitable for use in life support, lif e-critical or
safety-critical systems or equipment, nor in applications where failure or
malfunction of a Nexperia product can reasonably be expected
to result in perso nal injury, death or severe property or envi ronmental
damage. Nexperia and its suppliers accept no liability for
inclusion and/or use of Nexperia products in such equipment or
applications an d ther efo re su ch inclusi on a nd/or use is at the cu stome r's own
risk.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. Nexperia makes no
representation or warranty tha t such application s will be suitable for the
specified use without further testing or modification.
Customers are responsible for the design and ope ration of their applications
and products using Nexperia products, and Nexperia
accepts no liability for any assistance with applicati ons or customer product
design. It is customer’s sole responsibility to determine whether the Nexperia
product is suitable and fit for the customer’s applications and
products planned, as well as fo r the planned application and use of
customer’s third party customer(s). Customers should provide appropriate
design and operating safeguards to minimize the risks associated with their
applications and products.
Nexperia does not accept any liability related to any default,
damage, costs or problem which is based on any weakness or default in the
customer’s applications or products, or the application or use by customer’s
third party customer(s). Customer is responsible for doing all necessary
testing for the customer’s applications and products using Nexperia
products in order to avoid a default of the applications and
the products or of the application or use by customer’s third party
customer(s). Nexperia does not accept any liability in this respect.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) will cause permanent
damage to the device. Limiting values are stress ratings only and (proper)
operation of the device at these or any other conditions above those given in
the Recommended operating conditions section (if present) or the
Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanent ly and irreversibly affect
the quality and reliability of the device.
Terms and conditions of commercial sale — Nexperia
products are sold subject to the general terms and conditions of commercial
sale, as published at http://www.nexperia.com/profile/terms, unless otherwise
agreed in a valid written individua l agreement. In case an individual
agreement is concluded only the ter ms and conditions of the respective
agreement shall apply. Nexperia hereby expressly objects to
applying the customer’s general terms and conditions with regard to the
purchase of Nexperia products by customer.
Document status[1][2] Product status[3] Definition
Objective [short] data sheet Development This document contains data from the objective specification for product development.
Preliminary [short] dat a sheet Qualification This document contains data from the preliminary specification.
Product [short] dat a sheet Production This document contains the product specification.
© Nexperia B.V. 2017. All rights reserved
74HC_HCT4066_Q100 All information provided in this document is subject to legal disclaimers.
Product data sheet Rev. 3 — 16 December 2013 22 of 23
Nexperia 74HC4066-Q100; 74HCT4066-Q100
Quad single-pole single-throw analog switch
No offer to sell or license — Nothing in this document may be interpret ed or
construed as an of fer to sell product s that is op en for accept ance or the grant ,
conveyance or implication of any license under any copyrights, patents or
other industrial or intellectual property rights.
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from competent authorities.
Translations — A non-English (translated) version of a docume nt is for
reference only. The English version shall prevail in case of any discrepancy
between the translated and English versions.
16.4 Trademarks
Notice: All referenced b rands, produc t names, service names and trademarks
are the property of their respect i ve ow ners.
17. Contact information
For more information, please visit: http://www.nexperia.com
For sales office addresses, please send an email to: salesaddresses@nexperia.com
Nexperia 74HC4066-Q100; 74HCT4066-Q100
Quad single-pole single-throw analog switch
18. Contents
1 General description. . . . . . . . . . . . . . . . . . . . . . 1
2 Features and benefits . . . . . . . . . . . . . . . . . . . . 1
3 Ordering information. . . . . . . . . . . . . . . . . . . . . 2
4 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 2
5 Pinning information. . . . . . . . . . . . . . . . . . . . . . 3
5.1 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
5.2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3
6 Functional description . . . . . . . . . . . . . . . . . . . 4
7 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 4
8 Recommended operating conditions. . . . . . . . 4
9 Static characteristics. . . . . . . . . . . . . . . . . . . . . 5
10 Dynamic characteristics . . . . . . . . . . . . . . . . . . 9
11 Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
12 Additional dynamic characteristics . . . . . . . . 13
13 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 17
14 Abbreviations. . . . . . . . . . . . . . . . . . . . . . . . . . 20
15 Revision history. . . . . . . . . . . . . . . . . . . . . . . . 20
16 Legal information. . . . . . . . . . . . . . . . . . . . . . . 21
16.1 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 21
16.2 Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
16.3 Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . . 21
16.4 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 22
17 Contact information. . . . . . . . . . . . . . . . . . . . . 22
18 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
© Nexperia B.V. 2017. All rights reserved
For more information, please visit: http://www.nexperia.com
For sales office addresses, please send an email to: salesaddresses@nexperia.com
Date of release:
16 December 2013