E SEE NEW DESIGN RECOMMENDATIONS
December 1997
Order Number: 290530-006
n
Intel SmartVoltage Technology
5 V or 12 V Program/Erase
2.7 V, 3.3 V or 5 V Read Operation
n
Very High-Performance Read
5 V: 60 ns Access Time
3 V: 110 ns Access Time
2.7 V: 120 ns Access Time
n
Low Power Consumption
Max 60 mA Read Current at 5 V
Max 30 mA Read Current at
2.7 V–3.6 V
n
x8/x16-Selectable Input/Output Bus
28F400 for High Performance 16- or
32-bit CPUs
n
x8-Only Input/Output Architecture
28F004B for Space-Constrained
8-bit Applications
n
Optimized Array Blocking Architecture
One 16-KB Protected Boot Block
Two 8-KB Parameter Blocks
96-KB and 128-KB Main Blocks
Top or Bottom Boot Locations
n
Extended Temperature Operation
–40 °C to +85 °C
n
Extended Block Erase Cycling
100,000 Cycles at Commercial Temp
10,000 Cycles at Extended Temp
n
Automated Word/Byte Program and
Block Erase
Command User Interface
Status Registers
Erase Suspend Capability
n
SRAM-Compatible Write Interface
n
Automatic Power Savings Feature
n
Reset/Deep Power-Down Input
0.2 µA ICCTypical
Provides Reset for Boot Operations
n
Hardware Data Protection Feature
Absolute Hardware-Protection for
Boot Block
Write Lockout during Power
Transitions
n
Industry-Standard Surface Mount
Packaging
40-, 48-, 56-Lead TSOP
44-Lead PSOP
n
Footprint Upgradeable from 2-Mbit and
to 8-Mbit Boot Block Flash Memories
n
ETOX™ IV Flash Technology
New Design Recommendations:
For new 2.7 V–3.6 V VCC designs with this device, Intel recommends using the Smart 3 Advanced Boot
Block. Reference
Smart 3 Advanced Boot Block 4-Mbit, 8-Mbit, 16-Mbit Flash Memory Family
datasheet,
order number 290580.
For new 5 V VCC desi gns wi th thi s dev ic e, I ntel rec omm ends us ing the 4-M bit S mart 5 B oot Bl ock . Referenc e
Smart 5 Flash Memory Family
2, 4, 8 Mbit
datasheet, order number 290599.
These documents are also available at Intel’s website, http://www.intel.com/design/flcomp.
REFERENCE ONLY
4-MBIT SmartVoltage BOOT BLOCK
FLASH MEMORY FAMILY
28F400BV-T/B, 28F400CV-T/B, 28F004BV-T/B
28F400CE-T/B, 28F004BE-T/B
Information in this document is provided in connection with Intel products. No license, express or implied, by estoppel or
otherwise, to any intellectual property ri ghts is granted by this document. Except as provided in Intel’s Terms and Conditi ons of
Sale for such products, Intel assumes no liability whatsoever, and Intel disclaims any express or implied warranty, relating to
sale and/or use of Intel products including liability or warranties relating to fitness for a particular purpose, merchantability, or
infringement of any patent, copyright or other intellectual property ri ght. Intel products are not intended for use in medical, life
saving, or life sustaining applications.
Intel may make changes to specifications and product descriptions at any time, without notice.
The 28F400BV-T/B, 28F400CV-T/B, 28F004BV-T/B, 28F400CE-T/B, 28F004BE-T/B may contain design defects or errors
known as errata which may cause the product to deviate from published specifications. Current characterized errata are
available on request.
Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order.
Copies of documents which have an ordering number and are referenced in this document, or other Intel literature, may be
obtained from:
Intel Corporation
P.O. Box 5937
Denver, CO 80217-9808
or call 1-800-548-4725
or visit Intel’s Website at http:\\www.intel.com
COPYRIGHT © INTEL CORPORATION, 1997 CG-041493
*Third-party brands and names are the property of their respective owners.
E4-MBIT SmartVoltage BOOT BLOCK FAMILY
3
SEE NEW DESIGN RECOMMENDATIONS
CONTENTS
PAGE PAGE
1.0 PRODUCT FAMILY OVERVIEW.....................5
1.1 New Features in the SmartVoltage Products5
1.2 Main Features..............................................5
1.3 Applications..................................................7
1.4 Pinouts.........................................................7
1.5 Pin Descriptions.........................................11
2.0 PRODUCT DESCRIPTION............................13
2.1 Memory Blocking Organization...................13
2.1.1 One 16-KB Boot Block.........................13
2.1.2 Two 8-KB Parameter Blocks................13
2.1.3 One 96-KB + Three 128-KB Main
Blocks ................................................13
3.0 PRODUCT FAMILY PRINCIPLES OF
OPERATION ................................................15
3.1 Bus Operations ..........................................15
3.2 Read Operations........................................15
3.2.1 Read Array..........................................15
3.2.2 Intelligent Identifiers ............................17
3.3 Write Operations........................................17
3.3.1 Command User Interface (CUI)...........17
3.3.2 Status Register....................................20
3.3.3 Program Mode.....................................21
3.3.4 Erase Mode.........................................21
3.4 Boot Block Locking ....................................22
3.4.1 VPP = VIL for Complete Protection.......22
3.4.2 WP# = VIL for Boot Block Locking .......22
3.4.3 RP# = VHH or WP# = VIH for
Boot Block Unlocking .........................22
3.4.4 Upgrade Note for 8-Mbit 44-PSOP
Package.............................................22
3.5 Power Consumption...................................26
3.5.1 Active Power .......................................26
3.5.2 Automatic Power Savings (APS) .........26
3.5.3 Standby Power....................................26
3.5.4 Deep Power-Down Mode.....................26
3.6 Power-Up/Down Operation.........................26
3.6.1 RP# Connected to System Reset ........26
3.6.2 VCC, VPP and RP# Transitions.............27
3.7 Power Supply Decoupling ..........................27
3.7.1 VPP Trace on Printed Circuit Boards....27
4.0 ELECTRICAL SPECIFICATIONS..................28
4.1 Absolute Maximum Ratings........................28
4.2 Commercial Operating Conditions..............28
4.2.1 Applying VCC Voltages.........................28
4.3 Capacitance...............................................29
4.4 DC Characteristics—Commercial...............30
4.5 AC Characteristics—Read Only
Operations—Commercial ..........................34
4.6 AC Characteristics—WE# Controlled Write
Operations—Commercial ..........................37
4.7 AC Characteristics—CE# Controlled Write
Operations—Commercial ..........................40
4.8 Erase and Program Timings—Commercial.43
4.9 Extended Operating Conditions..................43
4.9.1 Applying VCC Voltages.........................44
4.10 Capacitance.............................................44
4.11 DC Characteristics—Extended
Temperature Operations............................45
4.12 AC Characteristics—Read Only
Operations—Extended Temperature.........51
4.13 AC Characteristics—WE# Controlled Write
Operations—Extended Temperature.........52
4.14 AC Characteristics—CE# Controlled Write
Operations—Extended Temperature.........54
4.15 Erase and Program Timings—Extended
Temperature..............................................55
5.0 ORDERING INFORMATION..........................56
6.0 ADDITIONAL INFORMATION.......................57
Related Intel Information..................................57
4-MBIT SmartVoltage BOOT BLOCK FAMILY E
4SEE NEW DESIGN RECOMMENDATIONS
REVISION HISTORY
Number Description
-001 Initial release of datasheet.
-002 Status changed from Product Preview to Preliminary
28F400CV/CE/BE references and information added throughout.
2.7 V CE/BE specs added throughout.
The following sections have been changed or rewritten: 1.1, 3.0, 3.2.1, 3.2.2, 3.3.1,
3.3.1.1, 3.3.2, 3.3.2.1, 3.3.3, 3.3.4, 3.6.2.
Note 2 added to Figure 3 to clarify 28F008B pinout vs. 28F008SA.
Sentence about program and erase WSM timeout deleted from Section 3.3.3, 3.3.4.
Erroneous arrows leading out of error states deleted from flowcharts in Figs. 9, 10.
Sections 5.1, 6.1 changed to “Applying VCC Voltages.” These sections completely
changed to clarify VCC ramp requirements.
IPPD 3.3 V Commercial spec changed from 10 to 5 µA.
Capacitance tables added after commercial and extended DC Characteristics tables.
Test and slew rate notes added to Figs. 12, 13, 19, 20, 21.
Test configuration drawings (Fig. 14, 22) consolidated into one, with component
values in table. (Component values also rounded off).
tELFL, tELFH, tAVFL changed from 7 to 5 ns for 3.3 V BV-60 commercial and 3.3 V
TBV-80 extended, 10 to 5 ns for 3.3 V BV-80 and BV-120 commercial.
tWHAX and tEHAX changed from 10 to 0 ns.
tPHWL changed from 1000 ns to 800 ns for 3.3 V BV-80, BV-120 commercial.
tPHEL changed from 1000 ns to 800 ns for 3.3 V BV-60, BV-80, and BV-120 commercial.
-003 28F400BE row removed from Table 1
Applying VCC voltages (Sections 5.1 and 6.1) rewritten for clarity.
Minor cosmetic changes/edits.
-004 Corrections: Spec typographical error “tQWL” corrected to read “tQVVL.”
Intel386™ EX Microprocessor block diagram updated because latest Intel386 CPU
specs require less glue logic.
Spec tELFL and tELFH changed from 5 ns (max) to 0 ns (min).
New specs tPLPH and tPLQX added from Specification Update document (297595).
Specs tEHQZ and tGHQZ improved on most voltage/speed combinations.
-005 Correction: Appendix A, Ordering information fixed order numbers from TE27F400BVT80
to TE28F400BVT80 and TE27F400BVB80 to TE28F400BVB80.
Updated disclaimer.
-006 Added
New Design Recommendations
section to cover page.
Updated
Erase Suspend/Resume Flowchart
.
E4-MBIT SmartVoltage BOOT BLOCK FAMILY
5
SEE NEW DESIGN RECOMMENDATIONS
1.0 PRODUCT FAMILY OVERVIEW
This datasheet contains the specifications for the
two branches of products in the SmartVoltage
4-Mbit boot bloc k f lash m emory fami ly : t he -BE/ CE
suffix products feature a low VCC operating range
of 2.7 V–3.6 V; the -BV/CV suffix products offer
3.0 V–3.6 V operation. Both BE/CE and BV/CV
products also operate at 5 V for high-speed
access times. Throughout this datasheet, the
28F400 refers to all x8/x16 4-Mbit products, while
28F004B refers to all x8 4-Mbit boot block
products . Also, the t erm “2.7 V” generally ref ers to
the full voltage range 2.7 V–3.6 V. Section 1.0
provides an overview of the flash memory family
including applications, pinouts and pin
descriptions. Sections 2.0 and 3.0 describe the
memory organization and operation for these
products. Section 4.0 contains the family’s
operating specifications. Finally, Sections 5.0 and
6.0 provide ordering and document reference
information.
1.1 New Features in the
SmartVoltage Products
The SmartV oltage boot block f lash memory family
offers identical operation with the BX/BL 12 V
program products, except for the dif ferences lis ted
below. All other functi ons are equivalent t o current
products, including signatures, Write commands,
and pinouts.
WP# pin has replaced a DU (Don’t Use) pin.
Connect the WP# pin to control signal or to
VCC or GND (in this case, a logic-level signal
can be placed on DU pin). See Tables 2 and 9
to see how the WP# pin works.
5 V program/erase operation has been added.
If switching VPP for write protection, switch to
GND (not 5 V) for complete write protection.
To take advantage of 5 V write-capability,
allow for connecting 5 V to VPP and
disconnecting 12 V from VPP line.
Enhanced circuits optimize low VCC
performance, allowing operation down to
VCC = 2.7 V (using the BE product).
If you are using BX/BL 12 V VPP boot block
products today, you should account for the
differences listed above and also allow for
connecting 5 V to VPP and disconnecting 12 V
from VPP line, if 5 V writes are desired.
1.2 Main Features
Intel’s SmartVoltage technology is the most
flexible voltage solution in the flash industry,
providing t wo discret e voltage supply pins: V CC for
read operation, and VPP for program and erase
operation. Discrete supply pins allow system
designers to use the optimal voltage levels for
their design. The 28F400BV/CV, 28F004BV,
28F400CE and 28F004BE provide program/erase
capability at 5 V or 12 V. The 28F400BV/CV and
28F004BV allow reads with VCC at 3.3 ± 0.3 V or
5 V, while the 28F400CE and 28F004BE allow
reads with V CC at 2.7 V–3. 6 V or 5 V. S ince many
designs read from the flash memory a large
percentage of the time, read operation using the
2.7 V or 3.3 V ranges can provide great power
savings . If read performanc e is an is sue, however,
5 V VCC provides faster read access times.
Table 1. SmartVoltage Provides Total Voltage Flexibility
Product Bus VCC VPP
Name Width 2.7 V–3.6 V 3.3 ± 0.3 V 5 V ± 5%
5 V ± 10% 5 V ± 10% 12 V ± 5%
28F004BV-T/B x8 √√√√
28F400BV-T/B x8 or x16 √√√√
28F400CV-T/B x8 or x16 √√√√
28F004BE-T/B x8 √√
28F400CE-T/B x8 or x16 √√
4-MBIT SmartVoltage BOOT BLOCK FAMILY E
6SEE NEW DESIGN RECOMMENDATIONS
For program and erase operations, 5 V VPP
operation elim inates the need for in system voltage
converters, while 12 V VPP operation provides
faster program and erase for situati ons where 12 V
is available, such as manufacturing or designs
where 12 V is in-system. For design simplicity,
however, just hook up VCC and VPP to t he sam e 5 V
± 10% source.
The 28F400/28F004B boot block flash memory
family is a high-performance, 4-Mbit (4, 194,304 bit)
flash memory family organized as either
256 Kwords of 16 bits each (28F400 only) or
512 Kbytes of 8 bits each (28F400 and 28F004B).
Separately erasable blocks, including a hardware-
lockable boot block (16,384 bytes), two parameter
blocks (8,192 bytes each) and main blocks (one
block of 98,304 bytes and three blocks of 131,072
bytes), define the boot block flash family
architecture. See Figures 7 and 8 for memory
maps. Eac h block can be independent ly erased and
programmed 100,000 times at commercial
temperature or 10,000 times at extended
temperature.
The boot block is locat ed at either the top (denoted
by -T suffix ) or the bottom (-B suffix ) of the address
map in order to accommodate different
microprocessor protocols for boot code location.
The hardware-lockable boot block provides
complet e code securi ty for the k ernel code required
for system initialization. Locking and unlocking of
the boot block is controlled by WP# and/or RP#
(see Section 3.4 for details).
The Command User Interface (CUI) serves as the
interface between the microprocessor or
microcontroller and the internal operation of the
boot block flash memory products. The internal
Write State Mac hine (WSM) automat ically ex ecutes
the algorithms and timings necessary for program
and erase operations, including verifications,
thereby unburdening the microprocessor or
microcontroller of these tasks. The Status Register
(SR) indic at es the status of the WSM and whet her it
successfully completed the desired program or
erase operation.
Program and Eras e A utomation all ows program and
erase operations to be executed using an industry-
standard two-write command sequence to the CUI.
Data writes are performed in word (28F400 family)
or byte (28F400 or 28F004B families) increments.
Each byte or word in the flash memory can be
programmed independently of other memory
locations, unlike erases, which erase all locations
within a block simultaneously.
The 4-Mbit SmartVoltage boot block flash memory
family is also designed with an Automatic Power
Savings (APS) feature which minimizes system
battery current drain, allowing for very low power
designs. To provide even greater power savings,
the boot block family includes a deep power-down
mode which minimizes power consumption by
turning most of the flash memory’s circuitry off. This
mode is controlled by the RP# pin and its usage is
discussed in Section 3.5, along with other power
consumption issues.
Additionally, the RP# pin provides protection
against unwanted command writes due to invalid
system bus conditions that may occur during
system reset and power-up/down sequences. For
example, when the flash memory powers-up, it
automatically defaults to the read array mode, but
during a warm system reset, where power
continues uninterrupted to the system components,
the flas h memory coul d remain i n a non-read m ode,
such as erase. Consequently, the system Reset
signal should be tied to RP # to reset t he memory t o
normal read mode upon activation of the Reset
signal. See Section 3.6.
The 28F400 provides both byte-wide or word-wide
input/output, which is controlled by the BYTE# pin.
Please see Table 2 and Figure 16 for a detailed
description of BYTE# operations, especially the
usage of the DQ15/A–1 pin.
The 28F400 products are available in a
ROM/EPROM-compatible pinout and housed in the
44-lead PSOP (Plastic Small Outline) package, the
48-lead TSOP (Thin Small Outline, 1.2 mm thick)
package and the 56-lead TSOP as shown in
Figures 4, 5 and 6, respectively. The 28F004
products are available in the 40-lead TSOP
package as shown in Figure 3.
Refer to the
DC Characteristics
, Section 4.4
(commercial temperature) and Section 4.11
(extended temperature), for complete current and
voltage specifications. Refer to the
AC
Characteristics
, Section 4.5 (commercial
temperature) and Section 4.12 (extended
tem perat ure), for read, write and erase performance
specifications.
E4-MBIT SmartVoltage BOOT BLOCK FAMILY
7
SEE NEW DESIGN RECOMMENDATIONS
1.3 Applications
The 4-Mbit boot block flash memory family
combines high-density, low-power, high-
performance, cost-effective flash memories with
blocking and hardware prot ection c apabilities. Their
flexibilit y and v ersatilit y reduc e cos ts t hroughout the
product li fe cycle. Flash memory is ideal for Jus t-In-
Time production flow, reducing system inventory
and costs, and eliminating component handling
during the production phase.
When your product is in the end-user’s hands, and
updates or feature enhancements become
necessary, flash mem ory reduces the update cost s
by allowing user-performed code changes instead
of costly product returns or technician calls.
The 4-Mbit boot block fl ash m emory f amily provides
full-function, blocked flash memories suitable for a
wide range of applications. These applications
include extended PC BIOS and ROM-able
applications storage, digital cellular phone program
and data storage, telecommunication boot/firmware,
printer firmware/font storage and various other
embedded applications where program and data
storage are required.
Reprogrammable systems, such as personal
computers, are ideal applications for the 4-Mbit
flash memory products. Increasing software
sophistication greatens the probability that a code
update will be required after the PC is shipped. For
example, the emerging of “plug and play” standard
in desktop and portable PCs enables auto-
configuration of ISA and PCI add-in cards.
However, since the plug and play specification
continues to evolve, a flash BIOS provides a cost-
effective capability to update existing PCs. In
addition, the parameter blocks are ideal for storing
the required auto-configuration parameters,
allowing you to integrate the BIOS PROM and
parameter storage EEPROM into a single
component, reducing parts costs while increasing
functionality.
The 4-Mbit flash memory products are also
excellent design solutions for digital cellular phone
and telecommunication switching applications
requiring very low power consumption, high-
performance, high-density storage capability,
modular software designs, and a small form factor
package. The 4-Mbit’s blocking scheme allows for
easy segmentation of the embedded code with
16 Kbytes of hardware-protected boot code, four
main blocks of program code and two parameter
blocks of 8 Kbytes each for frequently updated data
storage and diagnostic messages (e.g., phone
numbers, authorization codes).
Intel’s boot block architecture provides a flexible
voltage solution for the different design needs of
various applications. The asymmetrically-blocked
memory map allows the integration of several
memory component s into a s ingle fl ash devic e. The
boot block provides a secure boot PROM; the
parameter blocks can emulate EEPROM
functionality for parameter store with proper
software techniques; and the main blocks provide
code and data storage with access times fast
enough to execute code in place, decreasing RAM
requirements.
1.4 Pinouts
Intel’s SmartVoltage Boot Block architecture
provides upgrade paths in every package pinout to
the 8-Mbit density. The 28F004B 40-lead TSOP
pinout for space-constrained designs is shown in
Figure 3. The 28F400 44-lead PSOP pinout follows
the industry-standard ROM/EPROM pinout, as
shown in Figure 4. For designs that require x16
operation but have space concerns, refer to the
48-lead pinout in Fi gure 5. Furthermore, t he 28F400
56-lead TSOP pinout shown in Figure 6 provides
density upgrades t o fut ure higher dens ity boot bl ock
memories.
Pinouts for the corresponding 2-Mbit and 8-Mbit
components are also provided for convenient
reference. 4-Mbit pinouts are given on the chip
illustration in the center, with 2-Mbit and 8-Mbit
pinouts going outward from the center.
4-MBIT SmartVoltage BOOT BLOCK FAMILY E
8SEE NEW DESIGN RECOMMENDATIONS
A[18:1]
CS#
RD#
WR#
D[0:15]
A[0:17]
CE#
OE#
WE#
DQ[0:15]
28F400BV-60
RP#
i386™ EX CPU
(25 MHz)
RESET
RESET
0530_01
NOTE:
A data bus buffer may be needed for processor speeds above 25 MHz.
Figure 1. 28F400 Interface to Intel386™ EX Microprocessor
UCS#
80C188EB
-A
15
A
8
ALE
P1.X
WR#
RD#
RESIN#
System Reset
WE#
OE#
V
PP
ADDRESS
LATCHES
LE
ADDRESS
LATCHES
LE
CE#
A
0
-A
18
RP#
28F004-T
-AD
7
AD
0
A[16:18]
DQ
0
-DQ
7
WP#
V
CC
10K
P1.X
V
CC
0530_02
Figure 2. 28F004B Interface to Intel80C188EB 8-Bit Embedded Microprocessor
E4-MBIT SmartVoltage BOOT BLOCK FAMILY
9
SEE NEW DESIGN RECOMMENDATIONS
28F004B
Boot Block
40-Lead TSOP
10 mm x 20 mm
TO P VIE W
32
31
30
29
28
27
26
25
24
23
22
21
33
34
35
36
37
38
39
40
20
19
17
18
1
2
3
4
5
6
7
8
9
10
11
12
13
14
16
15
A
1
A
2
A
3
RP#
WE#
V
PP
A
16
A
15
A
7
A
6
A
5
A
4
A
14
A
13
A
8
A
9
A
11
A
12
WP#
DQ
7
CE#
OE#
GND
A
0
DQ
6
DQ
5
DQ
4
DQ
2
DQ
1
DQ
0
V
CC
DQ
3
A
17
GND
NC
A
10
NC
NC
NC
28F002B 28F002B
28F008B 28F008B
DQ
7
CE#
OE#
GND
A
0
DQ
6
DQ
5
DQ
4
DQ
2
DQ
1
DQ
0
V
CC
V
CC
DQ
3
A
17
GND
NC
A
10
NC
A
1
A
2
A
3
RP#
WE#
V
PP
A
16
A
15
A
7
A
6
A
5
A
4
A
14
A
13
A
8
A
9
A
11
A
12
WP#
A
1
A
2
A
3
RP#
WE#
V
PP
A
16
A
15
A
7
A
6
A
5
A
4
A
14
A
13
A
8
A
9
A
11
A
12
WP#
A
18
A
18
A
19
DQ
7
CE#
OE#
GND
A
0
DQ
6
DQ
5
DQ
4
DQ
2
DQ
1
DQ
0
V
CC
DQ
3
A
17
GND
NC
A
10
NC
NC
V
CC
V
CC
0530_03
Figure 3. The 40-Lead TSOP Offers the Smallest Form Factor for Space-Constrained Applications
PA28F400
Boot Bloc k
44-Lead PSOP
0.525" x 1.110"
TOP VIEW
32
31
30
29
28
27
26
25
24
23
33
34
35
36
37
38
39
40
41
42
43
44
22
21
20
19
17
18
1
2
3
4
5
6
7
8
9
10
11
12
13
14
16
15
RP#
WE#
A
A
A
A
A
A
A
A
A
BYTE#
GND
DQ /A
DQ
DQ
DQ
DQ
DQ
DQ
DQ
V
8
9
10
11
12
13
14
15
16
15
7
14
6
13
5
12
4
CC
-1
28F800 28F200
V
PP
WP#
NC
A
7
A
6
A
5
A
4
A
3
A
2
A
1
A
0
CE#
GND
OE#
DQ
0
DQ
8
DQ
1
DQ
9
DQ
2
DQ
10
DQ
3
DQ
11
V
PP
A
17
A
7
A
6
A
5
A
4
A
3
A
2
A
1
A
0
CE#
GND
OE#
DQ
0
DQ
8
DQ
1
DQ
9
DQ
2
DQ
10
DQ
3
DQ
11
A
18
V
PP
WP#
A
17
A
7
A
6
A
5
A
4
A
3
A
2
A
1
A
0
CE#
GND
OE#
DQ
0
DQ
8
DQ
1
DQ
9
DQ
2
DQ
10
DQ
3
DQ
11
RP#
WE#
A
A
A
A
A
A
A
A
A
BYTE#
GND
DQ /A
DQ
DQ
DQ
DQ
DQ
DQ
DQ
V
8
9
10
11
12
13
14
15
16
15
7
14
6
13
5
12
4
CC
-1
RP#
WE#
A
A
A
A
A
A
A
A
A
BYTE#
GND
DQ /A
DQ
DQ
DQ
DQ
DQ
DQ
DQ
V
8
9
10
11
12
13
14
15
16
15
7
14
6
13
5
12
4
CC
-1
28F80028F200
0530_04
NOTE: Pin 2 is WP# on 2- and 4-Mbit devices but A18 on the 8-Mbit because no other pins were available for the high order
address. Thus, the 8-Mbit in the 44-lead PSOP cannot unlock the boot block without RP# = VHH (12 V). To allow upgrades to
the 8 Mbit from 2/2 Mbit in this package, design pin 2 to control WP# at the 2/4 Mbit level and A
18 at the 8-Mbit density. See
Section 3.4 for details.
Figure 4. The 44-Lead PSOP Offers a Convenient Upgrade from JEDEC ROM Standards
4-MBIT SmartVoltage BOOT BLOCK FAMILY E
10 SEE NEW DESIGN RECOMMENDATIONS
28F400
Boot Bloc k
48-Lead T SOP
12 mm x 20 mm
TOP VIEW
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
24
23
22
21
20
19
17
18
1
2
3
4
5
6
7
8
9
10
11
12
13
14
16
15
25
26
27
28
29
30
31
32
16
15 -1
7
14
6
13
5
12
4
A
BYTE#
GND
DQ /A
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
V
DQ
DQ
DQ
DQ
DQ
DQ
DQ
OE#
GND
CE#
A
CC
11
3
10
2
9
1
8
0
0
16
15 -1
7
14
6
13
5
12
4
A
BYTE#
GND
DQ /A
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
V
DQ
DQ
DQ
DQ
DQ
DQ
DQ
OE#
GND
CE#
A
CC
11
3
10
2
9
1
8
0
0
28F80028F200
16
15 -1
7
14
6
13
5
12
4
A
BYTE#
GND
DQ /A
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
OE#
GND
CE#
A
V
CC
11
3
10
2
9
1
8
0
0
28F20028F800
A
A
A
A
A
A
A
A
NC
NC
WE#
RP#
WP#
NC
A
A
A
A
A
A
A
A
17
7
6
5
4
3
2
1
15
14
13
12
11
10
9
8
A
A
A
A
A
A
A
A
NC
NC
WE#
RP#
WP#
NC
NC
A
A
A
A
A
A
A
7
6
5
4
3
2
1
15
14
13
12
11
10
9
8
A
A
A
A
A
A
A
A
NC
NC
WE#
RP#
WP#
NC
NC
A
A
A
A
A
A
A
A
17
7
6
5
4
3
2
1
15
14
13
12
11
10
9
8
V
PP
V
PP
V
PP
A
18
NC
0530_05
Figure 5. The 48-Lead TSOP Offers the Smallest Form Factor for x16 Operation
28F400
56-Lead TSOP
Boot Block
14 mm x 20 mm
TOP VIEW
28
27
26
25
24
23
22
21
20
19
17
18
1
2
3
4
5
6
7
8
9
10
11
12
13
14
16
15
A
1
A
2
A
3
RP#
WE#
A
15
A
7
A
6
A
5
A
4
A
14
A
13
A
8
A
9
A
11
A
12
NC
V
PP
NC
NC
NC
NC
NC
NC
A
10
WP#
NC
NC
A
1
A
2
A
3
RP#
WE#
A
15
A
7
A
6
A
5
A
4
A
14
A
13
A
8
A
9
A
11
A
12
NC
V
PP
NC
NC
NC
NC
NC
NC
A
10
WP#
NC
DQ
7
CE#
OE#
GND
A
0
DQ
6
DQ
5
DQ
4
DQ
2
DQ
1
DQ
0
V
CC
V
CC
DQ
3
GND
NC
NC
DQ
9
DQ
10
DQ
11
DQ
8
BYTE#
DQ
15
/A
-1
DQ
14
DQ
13
DQ
12
A
16
NC
28F200 28F200
A
17
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
32
31
30
29
33
34
35
36
37
38
39
40
DQ
7
CE#
OE#
GND
A
0
DQ
6
DQ
5
DQ
4
DQ
2
DQ
1
DQ
0
V
CC
V
CC
DQ
3
GND
NC
NC
DQ
9
DQ
10
DQ
11
DQ
8
BYTE#
DQ
15
/A
-1
DQ
14
DQ
13
DQ
12
A
16
NC
0530_06
Figure 6. The 56-Lead TSOP Offers Compatibility between 2 and 4 Mbits
E4-MBIT SmartVoltage BOOT BLOCK FAMILY
11
SEE NEW DESIGN RECOMMENDATIONS
1.5 Pin Descriptions Table 2. 28F400/004 Pin Descriptions
Symbol Type Name and Function
A0–A18 INPUT ADDRESS INPUTS for memory addresses. Addresses are internally latched
during a write cycle. The 28F400 only has A0– A17 pins, while the 28F004B has
A0– A18.
A9INPUT ADDRESS INPUT: When A9 is at VHH the signature mode is accessed. During
this mode, A0 decodes between the manufacturer and device IDs. When BYTE#
is at a logic low, only the lower byte of the signatures are read. DQ15/A–1 is a
don’t care in the signature mode when BYTE# is low.
DQ0–DQ7INPUT/
OUTPUT DATA INPUTS/OUTPUTS: Inputs array data on the second CE# and WE# cycle
during a Program command. Inputs commands to the CUI when CE# and WE#
are active. Data is internally latched during the write cycle. Outputs array,
intelligent identifier and status register data. The data pins float to tri-state when
the chip is de-selected or the outputs are disabled.
DQ8–DQ15 INPUT/
OUTPUT DATA INPUTS/OUTPUTS: Inputs array data on the second CE# and WE# cycle
during a Program command. Data is internally latched during the write cycle.
Outputs array data. The data pins float to tri-state when the chip is de-selected or
the outputs are disabled as in the byte-wide mode (BYTE# = “0”). In the byte-wide
mode DQ15/A–1 becomes the lowest order address for data output on DQ0–DQ7.
The 28F004B does not include these DQ8–DQ15 pins.
CE# INPUT CHIP ENABLE: Activates the device’s control logic, input buffers, decoders and
sense amplifiers. CE# is active low. CE# high de-selects the memory device and
reduces power consumption to standby levels. If CE# and RP# are high, but not
at a CMOS high level, the standby current will increase due to current flow
through the CE# and RP# input stages.
OE# INPUT OUTPUT ENABLE: Enables the device’s outputs through the data buffers during
a read cycle. OE# is active low.
WE# INPUT WRITE ENABLE: Controls writes to the command register and array blocks. WE#
is active low. Addresses and data are latched on the rising edge of the WE#
pulse.
RP# INPUT RESET/DEEP POWER-DOWN: Uses three voltage levels (V
IL
, VIH, and VHH) to
control two different functions: reset/deep power-down mode and boot block
unlocking. It is backwards-compatible with the BX/BL/BV products.
When RP# is at logic low, the device is in reset/deep power-down mode,
which puts the outputs at High-Z, resets the Write State Machine, and draws
minimum current.
When RP# is at logic high, the device is in standard operation. When RP#
transitions from logic-low to logic-high, the device defaults to the read array mode.
When RP# is at VHH, the boot block is unlocked and can be programmed or
erased. This overrides any control from the WP# input.
4-MBIT SmartVoltage BOOT BLOCK FAMILY E
12 SEE NEW DESIGN RECOMMENDATIONS
Table 2. 28F400/004 Pin Descriptions (Continued)
Symbol Type Name and Function
WP# INPUT WRITE PROTECT: Provides a method for unlocking the boot block in a system
without a 12 V supply.
When WP# is at logic low, the boot block is locked, preventing program and
erase operations to the boot block. If a program or erase operation is attempted
on the boot block when WP# is low, the corresponding status bit (bit 4 for
program, bit 5 for erase) will be set in the status register to indicate the operation
failed.
When WP# is at logic high, the boot block is unlocked and can be
programmed or erased.
NOTE: This feature is overridden and the boot block unlocked when RP# is at
VHH. See Section 3.4 for details on write protection.
BYTE# INPUT BYTE# ENABLE: Not available on 28F004B. Controls whether the device
operates in the byte-wide mode (x8) or the word-wide mode (x16). BYTE# pin
must be controlled at CMOS levels to meet the CMOS current specification in the
standby mode.
When BYTE# is at logic low, the byte-wide mode is enabled, where data is
read and programmed on DQ0–DQ7 and DQ15/A–1 becomes the lowest order
address that decodes between the upper and lower byte. DQ8–DQ14 are tri-stated
during the byte-wide mode.
When BYTE# is at logic high, the word-wide mode is enabled, where data is
read and programmed on DQ0–DQ15.
VCC DEVICE POWER SUPPLY: 5.0 V ± 10%, 3.3 ± 0.3 V, 2.7 V–3.6 V (BE/CE only)
VPP PROGRAM/ERASE POWER SUPPLY: For erasing memory array blocks or
programming data in each block, a voltage either of 5 V ± 10% or 12 V ± 5% must
be applied to this pin. When VPP < VPPLK all blocks are locked and protected
against Program and Erase commands.
GND GROUND: For all internal circuitry.
NC NO CONNECT: Pin may be driven or left floating.
E4-MBIT SmartVoltage BOOT BLOCK FAMILY
13
SEE NEW DESIGN RECOMMENDATIONS
2.0 PRODUCT DESCRIPTION
2.1 Memory Blocking Organization
This product family features an asymmetrically-
blocked architecture providing system memory
integration. Each erase block can be erased
independently of the others up t o 100,000 times for
commercial temperature or up to 10,000 times for
extended temperature. The block sizes have been
chosen to optimize their functionality for common
applicat i ons of nonvolatile storage. The combinat i on
of block sizes in the boot block architecture allow
the integration of several memories into a single
chip. For the address locations of the blocks, see
the memory maps in Figures 4 and 5.
2.1.1 ONE 16-KB BOOT BLOCK
The boot block is intended to replace a dedicated
boot PROM in a microprocessor or microcontroller-
based system. The 16-Kbyte (16,384 bytes) boot
block is located at either the top (denoted by -T
suffix) or the bottom (-B suffix) of the address map
to accommodate different microproces sor protocols
for boot code location. This boot block features
hardware controllable write-prot ection to protect the
crucial microprocessor boot code from accidental
modification. The protection of the boot block is
controll ed using a combination of the VPP, RP#, and
WP# pins, as is detailed in Section 3.4.
2.1.2 TWO 8-KB PARAMETER BLOCKS
The boot block architecture includes parameter
blocks to facilitate storage of frequently updated
small parameters that would normally require an
EEPROM. By using software techniques, the byte-
rewrite functionality of EEPROMs can be emulated.
These techniques are detailed in Intel’s application
note,
AP-604 Using Intel’s Boot Block Flash
Memory Parameter Blocks to Replace EEPROM
.
Each boot bl ock component c ont ai ns two parameter
blocks of 8 Kbytes (8,192 bytes) each. The
parameter blocks are not write-protectable.
2.1.3 ONE 96-KB + THREE 128-KB
MAIN BLOCKS
After the allocation of address space to the boot
and parameter blocks, the remainder is div ided into
main blocks for data or code storage. Each 4-Mbit
device contains one 96-Kbyte (98,304 byte) block
and three 128-Kbyt e (131,072 by te) bl ocks. See the
memory maps for each device for more information.
4-MBIT SmartVoltage BOOT BLOCK FAMILY E
14 SEE NEW DESIGN RECOMMENDATIONS
3FFFFH
3E000H
3DFFFH
3D000H
3CFFFH
3C000H
3BFFFH
30000H
20000H
1FFFFH
10000H
0FFFFH
00000H
2FFFFH
3FFFFH
30000H
2FFFFH
20000H
1FFFFH
10000H
0FFFFH
04000H
03FFFH
03000H
02FFFH
02000H
01FFFH
00000H
28F400-T
8-Kbyte PARAMETE R BLOCK
16-Kby t e BOOT BLOCK
8-Kbyte PARAMETE R BLOCK
96-Kbyte MAIN BLOCK
128-Kbyte MAIN BLO CK
128-Kbyte MAIN BLO CK
128-Kbyte MAIN BLO CK
28F400-B
8-Kbyte PARAMETER BLOCK
16-Kby t e BOOT BLOCK
8-Kbyte PARAMETER BLOCK
96-Kbyt e MAIN BLOCK
128-Kbyte MAIN BLO CK
128-Kbyte MAIN BLO CK
128-Kbyte MAIN BLO CK
0530_07
NOTE: Address = A[17:0]. In x8 operation, the least significant system address should be connected to A
-1. Memory maps are
shown for x16 operation.
Figure 7. Word-Wide x16-Mode Memory Maps
7FFFFH
7C000H
7BFFFH
7A000H
79FFFH
78000H
77FFFH
60000H
5FFFFH
40000H
3FFFFH
20000H
1FFFFH
00000H
28F004-T
128-Kb yte MAI N B LOCK
8-Kbyte PARAMETER BLOCK
16-Kbyte BOOT BLOCK
8-Kbyte PARAMETER BLOCK
96-Kbyte MAIN BLOCK
128-Kb yte MAI N B LOCK
128-Kb yte MAI N B LOCK
7FFFFH
60000H
5FFFFH
40000H
3FFFFH
20000H
1FFFFH
08000H
07FFFH
06000H
05FFFH
04000H
03FFFH
00000H
28F004-B
128-Kb yte MAI N B LOCK
8-Kbyte PARAMETER BLOCK
16-Kbyte BOOT BLOCK
8-Kbyte PARAMETER BLOCK
96-Kbyte MAIN BLOCK
128-Kb yte MAI N B LOCK
128-Kb yte MAI N B LOCK
0530_08
NOTE: Address = A[18:0]. These memory maps apply to the 28F004B or the 28F400 in x8 mode.
Figure 8. Byte-Wide x8-Mode Memory Maps
E4-MBIT SmartVoltage BOOT BLOCK FAMILY
15
SEE NEW DESIGN RECOMMENDATIONS
3.0 PRODUCT FAMILY PRINCIPLES
OF OPERATION
Flash memory combines EPROM functionality with
in-circuit electrical write and erase. The boot block
flash family utilizes a Command User Interface
(CUI) and automated algorithms to simplify write
and erase operations. The CUI allows for 100%
TTL-level control inputs, fixed power supplies
during erasure and programming, and maximum
EPROM compatibility.
When VPP < VPPLK, the device will only successfully
execute the following commands: Read Array,
Read Status Register, Clear Status Register and
intelligent identifier mode. The device provides
standard EP ROM read, standby and output dis able
operations. Manufacturer identification and device
identif icat ion dat a can be ac ces sed t hrough the CUI
or through the standard EPROM A9 high voltage
access (VID) for PROM programming equipment.
The same EPROM read, standby and output
disable functions are avail able when 5 V or 12 V is
applied to the VPP pin. In addition, 5 V or 12 V on
VPP allows write and erase of the device. All
functi ons as soc iat ed with al tering m emory cont ents :
Program and Erase, Intelligent Identifier Read, and
Read Status are accessed via the CUI.
The internal Write State Machi ne (WS M ) completely
automates program and erase, beginning operation
signaled by the CUI and reporting status through
the status register. The CUI handles the WE#
interface to the data and address latches, as well
as system status requests during WSM operation.
3.1 Bus Operations
Flash memory reads, erases and writes in-system
via the local CPU. All bus cycles to or from the flash
memory conform to standard microprocessor bus
cycles. These bus operations are summarized in
Tables 3 and 4.
3.2 Read Operations
3.2.1 READ ARRAY
When RP# transitions from VIL (reset) to VIH, the
device will be in the read array mode and will
respond to the read control inputs (CE#, address
inputs, and OE#) without any commands being
written to the CUI.
When the device is in the read array mode, five
control signals must be controlled to obtain data at
the outputs.
RP# must be logic high (VIH)
WE# must be logic high (VIH)
BYTE# must be logic high or logic low
CE# must be logic low (VIL)
OE must be logic low (VIL)
In addition, the addres s of the des ired loc ation m ust
be applied to the address pins. Refer to Figures 15
and 16 for the exact sequence and timing of these
signals.
If the dev ice is not in read array mode, as would be
the case after a program or erase operation, the
Read Mode command (FFH) mus t be written to the
CUI before reads can take place.
During system design, consideration should be
taken to ensure address and control inputs meet
required input slew rates of <10 ns as defined in
Figures 12 and 13.
4-MBIT SmartVoltage BOOT BLOCK FAMILY E
16 SEE NEW DESIGN RECOMMENDATIONS
Table 3. Bus Operations for Word-Wide Mode (BYTE# = VIH)
Mode Notes RP# CE# OE# WE# A9A0VPP DQ0–15
Read 1,2,3 VIH VIL VIL VIH XXX D
OUT
Output Disable VIH VIL VIH VIH X X X High Z
Standby VIH VIH XXXXXHigh Z
Deep Power-Down 9 VIL XXXXXXHigh Z
Intelligent Identifier
(Mfr) 4V
IH VIL VIL VIH VID VIL X 0089 H
Intelligent Identifier
(Device) 4,5 VIH VIL VIL VIH VID VIH X See
Table 5
Write 6,7,8 VIH VIL VIH VIL XXX D
IN
Table 4. Bus Operations for Byte-Wide Mode (BYTE# = VIL)
Mode Notes RP# CE# OE# WE# A9A0A–1 VPP DQ0–7 DQ8–14
Read 1,2,3 VIH VIL VIL VIH XXXXD
OUT High Z
Output
Disable VIH VIL VIH VIH XXXXHigh Z High Z
Standby VIH VIH XXXXXXHigh Z High Z
Deep Power-
Down 9V
IL XXXXXXXHigh Z High Z
Intelligent
Identifier (Mfr) 4V
IH VIL VIL VIH VID VIL X X 89H High Z
Intelligent
Identifier
(Device)
4,5 VIH VIL VIL VIH VID VIH X X See
Table
5
High Z
Write 6,7,8 VIH VIL VIH VIL XXXXD
IN High Z
NOTES:
1. Refer to
DC Characteristics
.
2. X can be VIL, VIH for control pins and addresses, VPPLK or VPPH for VPP.
3. See
DC Characteristics
for VPPLK, VPPH1, VPPH2, VHH, VID voltages.
4. Manufacturer and device codes may also be accessed via a CUI write sequence, A1–A17 = X, A1–A18 = X.
5. See Table 5 for device IDs.
6. Refer to Table 7 for valid DIN during a write operation.
7. Command writes for block erase or word/byte program are only executed when V
PP = VPPH1 or VPPH2.
8. To write or erase the boot block, hold RP# at VHH or WP# at VIH. See Section 3.4.
9. RP# must be at GND ± 0.2 V to meet the maximum deep power-down current specified.
E4-MBIT SmartVoltage BOOT BLOCK FAMILY
17
SEE NEW DESIGN RECOMMENDATIONS
3.2.2 INTELLIGENT IDENTIFIERS
To read the manufacturer and device codes, the
device must be in intelligent identifier read mode,
which can be reached using two methods: by
writing the Intelligent Identifier command (90H) or
by taking the A9 pin to VID. Once in intelligent
identifier read mode, A0 = 0 outputs the manu-
facturer’ s identifi cation code and A 0 = 1 outputs the
device code. In byte-wide m ode, only the lower byte
of the above signatures is read (DQ15/A–1 is a
“don’t care” in this mode). See Table 5 for product
signatures. To return to read array mode, write a
Read Array command (FFH).
Table 5. Intelligent Identifier Table
Product Mfr. ID Device ID
-T
(Top Boot) -B
(Bottom Boot)
28F400 0089 H 4470 H 4471 H
28F004 89 H 78 H 79 H
3.3 Write Operations
3.3.1 COMMAND USER INTERFACE (CUI)
The Command User Interf ace (CUI) is the int erface
between the microprocessor and the internal chip
controller. Commands are written to the CUI using
standard microprocessor write timings. The
available commands are Read Array, Read
Intelligent Identifier, Read Status Register, Clear
Status Register, Erase and Program (summarized
in Tables 6 and 7). The three read modes are read
array, intelligent identifier read, and status register
read. For Program or Erase commands, the CUI
informs the Write State M achine (WSM) t hat a writ e
or erase has been requested. During the execution
of a Program command, the WSM will control the
programming sequences and the CUI will only
respond to s tatus reads. During an erase cycle, the
CUI will respond to status reads and erase
suspend. After the WSM has completed its task, it
will set the WSM status bit to a “1” (ready), which
indicates that the CUI can respond to its full
command set. Note that after the WSM has
returned control to the CUI, the CUI will stay in the
current command state until it receives another
command.
3.3.1.1 Command Function Description
Device operations are selected by writing specific
commands into the CUI. Tables 6 and 7 define the
available commands.
4-MBIT SmartVoltage BOOT BLOCK FAMILY E
18 SEE NEW DESIGN RECOMMENDATIONS
Table 6. Command Codes and Descriptions
Code Device Mode Decryption
00 Invalid/
Reserved Unassigned commands that should not be used. Intel reserves the right to redefine
these codes for future functions.
FF Read Array Places the device in read array mode, so that array data will be output on the data
pins.
40 Program
Set-Up Sets the CUI into a state such that the next write will latch the address and data
registers on the rising edge and begin the program algorithm. The device then
defaults to the read status mode, where the device outputs status register data
when OE# is enabled. To read the array, issue a Read Array command.
To cancel a program operation after issuing a Program Set-Up command, write all
1’s (FFH for x8, FFFFH for x16) to the CUI. This will return to read status register
mode after a standard program time without modifying array contents. If a program
operation has already been initiated to the WSM this command can not cancel that
operation in progress.
10 Alternate
Prog Set-Up (See 40H/Program Set-Up)
20 Erase
Set-Up Prepares the CUI for the Erase Confirm command. If the next command is not an
Erase Confirm command, then the CUI will set both the program status (SR.4) and
erase status (SR.5) bits of the status register to a “1,” place the device into the
read status register state, and wait for another command without modifying array
contents. This can be used to cancel an erase operation after the Erase Set-Up
command has been issued. If an operation has already been initiated to the WSM
this can not cancel that operation in progress.
D0 Erase
Resume/
Erase
Confirm
If the previous command was an Erase Set-Up command, then the CUI will latch
address and data, and begin erasing the block indicated on the address pins.
During erase, the device will respond only to the Read Status Register and Erase
Suspend commands and will output status register data when OE# is toggled low.
status register data is updated by toggling either OE# or CE# low.
B0 Erase
Suspend Valid only while an erase operation is in progress and will be ignored in any other
circumstance. Issuing this command will begin to suspend erase operation. The
status register will indicate when the device reaches erase suspend mode. In this
mode, the CUI will respond only to the Read Array, Read Status Register, and
Erase Resume commands and the WSM will also set the WSM status bit to a “1”
(ready). The WSM will continue to idle in the SUSPEND state, regardless of the
state of all input control pins except RP#, which will immediately shut down the
WSM and the remainder of the chip, if it is made active. During a suspend
operation, the data and address latches will remain closed, but the address pads
are able to drive the address into the read path. See Section 3.3.4.1.
70 Read Status
Register Puts the device into the read status register mode, so that reading the device
outputs status register data, regardless of the address presented to the device.
The device automatically enters this mode after program or erase has completed.
This is one of the two commands that is executable while the WSM is operating.
See Section 3.3.2.
E4-MBIT SmartVoltage BOOT BLOCK FAMILY
19
SEE NEW DESIGN RECOMMENDATIONS
Table 6. Command Codes and Descriptions (Continued)
Code Device Mode Decryption
50 Clear Status
Register The WSM can only set the program status and erase status bits in the status
register to “1;” it cannot clear them to “0.”
The status register operates in this fashion for two reasons. The first is to give the
host CPU the flexibility to read the status bits at any time. Second, when
programming a string of bytes, a single status register query after programming the
string may be more efficient, since it will return the accumulated error status of the
entire string. See Section 3.3.2.1.
90 Intelligent
Identifier Puts the device into the intelligent identifier read mode, so that reading the device
will output the manufacturer and device codes. (A0 = 0 for manufacturer,
A0 = 1 for device, all other address inputs are ignored). See Section 3.2.2.
Table 7. Command Bus Definitions
First Bus Cycle Second Bus Cycle
Command Note Oper Addr Data Oper Addr Data
Read Array 8 Write X FFH
Intelligent Identifier 1 Write X 90H Read IA IID
Read Status Register 2,4 Write X 70H Read X SRD
Clear Status Register 3 Write X 50H
Word/Byte Program Write PA 40H Write PA PD
Alternate Word/Byte
Program 6,7 Write PA 10H Write PA PD
Block Erase/Confirm 6,7 Write BA 20H Write BA D0H
Erase Suspend 5 Write X B0H
Erase Resume Write X D0H
ADDRESS DATA
BA = Block Address SRD = Status Register Data
IA = Identifier Address IID = Identifier Data
PA = Program Address PD = Program Data
X = Don’t Care
NOTES:
1. Bus operations are defined in Tables 3 and 4.
2. IA = Identifier Address: A0 = 0 for manufacturer code, A0 = 1 for device code.
3. SRD - Data read from status register.
4. IID = Intelligent Identifier Data. Following the Intelligent Identifier command, two read operations access manufacturer and
device codes.
5. BA = Address within the block being erased.
6. PA = Address to be programmed. PD = Data to be programmed at location PA.
7. Either 40H or 10H commands is valid.
8. When writing commands to the device, the upper data bus [DQ8–DQ15] = X (28F400 only) which is either VIL or VIH, to
minimize current draw.
4-MBIT SmartVoltage BOOT BLOCK FAMILY E
20 SEE NEW DESIGN RECOMMENDATIONS
Table 8. Status Register Bit Definition
WSMS ESS ES DWS VPPS R R R
76543210
NOTES:
SR.7 = WRITE STATE MACHINE STATUS
1 = Ready (WSMS)
0 = Busy
Check WSM bit first to determine Word/Byte
program or Block Erase completion, before
checking program or erase status bits.
SR.6 = ERASE-SUSPEND STATUS (ESS)
1 = Erase Suspended
0 = Erase In Progress/Completed
When erase suspend is issued, WSM halts
execution and sets both WSMS and ESS bits to
“1.” ESS bit remains set to “1” until an Erase
Resume command is issued.
SR.5 = ERASE STATUS (ES)
1 = Error In Block Erasure
0 = Successful Block Erase
When this bit is set to “1,” WSM has applied the
max number of erase pulses to the block and is
still unable to verify successful block erasure.
SR.4 = PROGRAM STATUS (DWS)
1 = Error in Byte/Word Program
0 = Successful Byte/Word Program
When this bit is set to “1,” WSM has attempted
but failed to program a byte or word.
SR.3 = VPP STATUS (VPPS)
1 = VPP Low Detect, Operation Abort
0 = VPP OK
The VPP status bit does not provide continuous
indication of VPP
level. The WSM interrogates VPP
level only after the Byte Write or Erase command
sequences have been entered, and informs the
system if VPP has not been switched on. The VPP
status bit is not guaranteed to report accurate
feedback between VPPLK and VPPH.
SR.2-SR.0 = RESERVED FOR FUTURE
ENHANCEMENTS (R) These bits are reserved for future use and should
be masked out when polling the status register.
3.3.2 STATUS REGISTER
The device status register indicates when a
program or erase operation is complete, and the
success or failure of that operation. To read the
status register write the Read Status (70H)
command to the CUI. This causes all subsequent
read operations to output data from the status
register until another command is written to the
CUI. To return to reading from the array, issue a
Read Array (FFH) command.
The status register bits are output on DQ0–DQ7, in
both byte-wi de (x8) or word-wi de (x16) mode. I n t he
word-wide mode the upper byte, DQ8–DQ15,
outputs 00H during a Read S tatus c ommand. I n the
byte-wide mode, DQ8–DQ14 are tri-stated and
DQ15/A–1 retains the low order address function.
Important: The contents of the status register
are latched on the falling edge of OE# or CE#,
whichever occurs last in the read cycle. This
prevents possible bus errors which might occur if
status register contents change while being read.
CE# or OE# mus t be toggled with each s ubsequent
status read, or the status register will not indicate
completion of a program or erase operation.
When the WSM is active, the SR.7 register will
indicate the status of the WSM, and will also hold
the bits indicating whether or not the WSM was
successful in performing the desired operation.
E4-MBIT SmartVoltage BOOT BLOCK FAMILY
21
SEE NEW DESIGN RECOMMENDATIONS
3.3.2.1 Clearing the Status Register
The WSM sets status bits 3 through 7 to “1,” and
clears bits 6 and 7 to “0,” but cannot clear status
bits 3 t hrough 5 to “0.” Bits 3 through 5 can only be
cleared by the controlling CPU through the use of
the Clear Status Regis ter (50H) c ommand, becaus e
these bits indicate various error conditions. By
allowing the system software to control the resetting
of these bits, several operations may be performed
(such as cumulatively programming several bytes
or erasing multiple blocks in sequence) before
reading the status register to determine if an error
occurred during that series. Cl ear the status register
before beginning another command or sequence.
Note, again, that a Read Array command must be
issued before data can be read f rom the mem ory or
intelligent identifier.
3.3.3 PROGRAM MODE
Programming is executed using a two-write
sequence. The P rogram Set-Up command is written
to the CUI followed by a second write which
specifies the address and data to be programmed.
The WSM will execute a sequence of internally
timed events to:
1. Program the desired bits of the addressed
memory word or byte.
2. Verify that the desired bits are sufficiently
programmed.
Programming of the memory results in specific bits
within a byte or word being changed to a “0.”
If the user attempts to program “1”s, there will be no
change of the memory cell content and no error
occurs.
The status register indicates programming status:
while the program sequence is executing, bit 7 of
the status register is a “0.” The status register can
be polled by toggling either CE# or OE#. While
programming, the only valid command is Read
Status Register.
When programming is complete, the program status
bits should be checked. If the programming
operation was unsuccessful, bit 4 of the status
register i s s et t o a “1” to indic ate a Program Fail ure.
If bit 3 is set to a “1,” then VPP was not within
accept able limit s, and t he WSM did not ex ecute t he
programming sequence.
The status register should be cleared before
attempting the next operation. Any CUI instruction
can follow after programming is completed;
however, reads f rom the memory array or int elligent
identifier cannot be accomplished until the CUI is
given the appropriate command.
3.3.4 ERASE MODE
To erase a block , wri te t he Erase S et-Up and Eras e
Confirm commands to the CUI, along with the
addresses identi fy ing the bl ock to be erased. Thes e
addresses are latched internally when the Erase
Confirm command is issued. Block erasure results
in all bits withi n the block being s et to “1.” Only one
block can be erased at a time.
The WSM will execute a sequence of internally
timed events to:
1. Program all bits within the block to “0.”
2. Verify that all bits within the block are
sufficiently programmed to “0.”
3. Erase all bits within the block to “1.”
4. Verify that all bits within the block are
sufficiently erased.
While the erase sequence is executing, bit 7 of the
status register is a “0.”
When the status register indicates that erasure is
complete, check the erase status bit to verify that
the erase operation was successful. If the erase
operation was unsuccessful, bit 5 of the status
register will be set to a “1,” indicating an Erase
Failure. If VPP was not wi thin accept able limits after
the Erase Confirm command is issued, the WSM
will not execute an erase sequence; instead, bit 5 of
the status register is set to a “1” to indicate an
Erase Failure, and bit 3 is set to a “1” to identify that
VPP supply voltage was not within acceptable limits.
Clear the status register before attempting the next
operation. Any CUI instruction can follow after
erasure is completed; however, reads from the
memory array, status register, or intelligent
identifier cannot be accomplished until the CUI is
given the Read Array command.
4-MBIT SmartVoltage BOOT BLOCK FAMILY E
22 SEE NEW DESIGN RECOMMENDATIONS
3.3.4.1 Suspending and Resuming Erase
Since an erase operation requires on the order of
seconds to complete, an E rase Suspend com mand
is provided to allow erase-sequence interruption in
order to read data from another block of the
memory. Once the erase sequence is started,
writing the Erase Suspend command to the CUI
requests that the WSM pause the erase sequence
at a predetermi ned poi nt i n the erase algorithm. The
status register will indicate if/when the erase
operation has been suspended.
At thi s point , a Read A rray c omm and can be writ ten
to the CUI in order to read data from blocks other
than that which is being suspended. The only ot her
valid command at this time is the Erase Resume
command or Read Status Register command.
During erase sus pend mode, the chi p can go into a
pseudo-standby mode by taking CE# to VIH, which
reduces active current draw.
To resume the erase operation, enable the chip by
taking CE# to VIL, then issuing the Erase Resume
command, which continues the erase sequence to
completion. As with the end of a standard erase
operation, t he st atus regis ter mus t be read, cl eared,
and the next instruction issued in order to continue.
3.4 Boot Block Locking
The boot block family architecture features a
hardware-lockable boot block so that the kernel
code for the system can be kept secure while the
parameter and main blocks are programmed and
erased independently as necessary. Only the boot
block can be locked independently from the other
blocks. The truth table, Table 9, clearly defines the
write protection methods.
3.4.1 VPP = VIL FOR COMPLETE
PROTECTION
For complete write protection of all blocks in the
flash device, the VPP programming voltage can be
held low. When VPP i s below V PPLK, any program or
erase operation will result in a error in the status
register.
3.4.2 WP# = VIL FOR BOOT BLOCK
LOCKING
When WP# = VIL, the boot block is locked and any
program or erase operation to the boot block will
result in an error in the status register. All other
blocks remain unlocked in this condition and can be
programmed or erased normally. Note that this
feature is overridden and the boot block unlocked
when RP# = VHH.
3.4.3 RP# = VHH OR WP# = VIH FOR BOOT
BLOCK UNLOCKING
Two methods can be used to unlock the boot block:
1. WP# = VIH
2. RP# = VHH
If both or ei ther of thes e two c onditi ons are m et, t he
boot block will be unlocked and can be
programmed or erased.
3.4.4 UPGRADE NOTE FOR 8-MBIT
44-PSOP PACKAGE
If upgradability to 8 Mbit is required, note that the
8 Mbit in the 44-PSOP does not have a WP#
because no pins were available for the 8-Mbit
upgrade address. Thus, in this density-package
combinat ion only, VHH (12 V) on RP# i s required to
unlock the boot block. Unlocking with a logic-level
signal is not possible. If this functionality is
required, and 12 V is not available, consider using
the 48-TSOP package, which has a WP# pin and
can be unlocked with a logic-level signal. All other
density-package combinations have WP# pins.
Table 9. Write Protection Truth Table
VPP RP# WP# Write Protection
Provided
VIL X X All Blocks Locked
VPPLK VIL X All Blocks Locked
(Reset)
VPPLK VHH X All Blocks Unlocked
VPPLK VIH VIL Boot Block Locked
VPPLK VIH VIH All Blocks Unlocked
E4-MBIT SmartVoltage BOOT BLOCK FAMILY
23
SEE NEW DESIGN RECOMMENDATIONS
SR.7 = 1
?
NO
YES
Start
Write 40H,
Word/Byte Address
Write Word/Byte
Data/Address
Full Status
Check if Desired
Word/Byte Progr am
Complete
FULL STATUS CHECK PROCEDURE
1
0
Read Status Register
Data (See Above)
1
0
Read
Status Register
VPP Range Error
Bus
Operation
Standby
Standby
Check SR.3
1 = VPP Low Detect
SR.3 MUST be cleared, i f set durin g a program attem pt,
before further attempts are all owed by the Write State Machine.
SR.4 is only cleared by the Clear Status Register command,
in cases where multiple bytes are progr ammed before full
status is checked.
If error is detec ted, clear the S tatus Register before attempting
retry or other error recovery.
Bus
Operation Command Comments
Write
Write
Setup
Program
Data = Data to Program
Addr = Location to Progr am
Read
Data = 40H
Addr = Word/Byte to Program
Check SR.7
1 = WSM Ready
0 = WSM Busy
Repeat for subsequ ent word/ byt e pr ogram operations.
SR Full Stat us Check can be done after each wor d/ byte progr am ,
or after a sequence of word/byte programs.
Write FFH after the last pr ogr am operat ion to reset device to
read array mode.
Standby
SR.3=
SR.4 = Word/Byte Progr am
Error
Word/Byte Program
Successful
Check SR.4
1 = Word/By te Progr am Er ror
Program
Status Register Dat a
Toggle CE# or OE#
to Update SRD.
Command Comments
0530_09
Figure 9. Automated Word/Byte Programming Flowchart
4-MBIT SmartVoltage BOOT BLOCK FAMILY E
24 SEE NEW DESIGN RECOMMENDATIONS
SR.7 = 0
1
Start
Write 20H,
Block Addr ess
Write D0H and
Block Address
Full St atus
Check if Desired
Block Erase
Complete
FULL STATUS CHECK PROCEDUR E
1
0
Read Status Register
Data (See Above)
1
0
Read Status
Register
VPP Range Error
Suspend
Erase
Suspend Erase
Loop
YES
NO
1
0
Command Sequence
Error
SR.3 =
SR.5 =
SR.4 ,5 =
Block Erase Error
Bus
Operation Command Comments
Standby
Check SR.4,5
Both 1 = Com ma nd Sequenc e Error
Standby
Check SR.3
1 = VPP Low Detect
SR.3 MUST be cleared, i f set during an erase attempt, befor e further
attempt s are allowed by the Wri te State M achine.
SR.5 is onl y cleared by t he Clear Status Register C ommand, in
cases where multiple blocks are erase be fore full status is checked.
If error is detec ted, clear the Status Register before attempting
retry or other error recov ery.
Check SR.5
1 = Block E rase Error
Standby
Bus
Operation Command Comments
Write
Write
Eras e Se tup
Read
Data = 20H
Addr = Within Block to Be Erased
Check SR. 7
1 = WSM Ready
0 = WSM Busy
Repeat for subsequent block erasures.
Full Status Check can be done after each block erase, or after a
sequence of block erasures.
Write FFH after the last oper ation to r eset device to read arr ay mode.
Status Register Data Toggle CE#
or OE# to Update Status Register
Standby
Erase
Confirm Data = D0H
Addr = Within Block to Be Erased
Block Erase Su cce ssf ul
0530_10
Figure 10. Automated Block Erase Flowchart
E4-MBIT SmartVoltage BOOT BLOCK FAMILY
25
SEE NEW DESIGN RECOMMENDATIONS
Start
Write B0H
Read Status Register
No
Comments
Data = B0H
Addr = X
Data = FFH
Addr = X
SR.7 =
SR.6 =
1
Write FFH
Read Array Data
Erase Completed
Done
Reading
Yes
Write FFHWrite D0H
Erase Resumed Read Array Data
0
1
Read array data from block
other than the one being
programmed.
Status Register Data Toggle
CE# or OE# to Update Status
Register Data
Addr = X
Check SR.7
1 = WSM Ready
0 = WSM Busy
Check SR.6
1 = Erase Suspended
0 = Erase Completed
Data = D0H
Addr = X
Bus
Operation
Write
Write
Read
Read
Standby
Standby
Write
Command
Program
Suspend
Read Array
Program
Resume
0
Write 70H
Status Register Data Toggle
CE# or OE# to Update Status
Register Data
Addr = X
Write
Write
Write
Read
Read
Standby
Standby
Write
Data=70H
Addr=X
Command
Program
Suspend
Read Array
Program
Resume
Erase Suspend
Read Status
Read Array
Erase Resume
0530_11
Figure 11. Erase Suspend/Resume Flowchart
4-MBIT SmartVoltage BOOT BLOCK FAMILY E
26 SEE NEW DESIGN RECOMMENDATIONS
3.5 Power Consumption
3.5.1 ACTIVE POWER
With CE# at a logic-low level and RP# at a logic-
high level, the device is placed in the active mode.
Refer to the
DC Characteri stic s
table for I CC current
values.
3.5.2 AUTOMATIC POWER SAVINGS (APS)
Automatic Power Savings (APS) provides low-
power operation during active mode. Power
Reduction Control (PRC) circuitry allows the dev ice
to put itself into a low current state when not being
accessed. After data is read from the memory
array, PRC logic controls the device’s power
consumption by entering the APS mode where
typical ICC current is less than 1 mA. The device
stays in this static state with outputs valid until a
new location is read.
3.5.3 STANDBY POWER
With CE# at a logic-high level (VIH), and the CUI in
read mode, the m emory is placed in standby mode,
which disables much of the device’s circuitry and
substantially reduces power consumption. Outputs
(DQ0–DQ15 or DQ0–DQ7) are placed in a high-
impedance state independent of the status of the
OE# signal. When CE# is at logic-high level during
erase or program operations, the device will
continue to perform the operation and consume
corresponding active power until the operation is
completed.
3.5.4 DEEP POWER-DOWN MODE
The SmartVoltage boot block family supports a low
typical ICC in deep power-down mode, which turns
off all circ uit s t o sav e power. This mode i s act iv ated
by the RP# pin when it is at a logic-low (GND ±
0.2 V). Note: BYTE # pin mus t be at CMOS level s t o
meet the ICCD specification.
During read modes, the RP# pin going low de-
select s t he memory and plac es t he output driv ers in
a high impedance state. Recovery from the deep
power-down state, requires a minimum acc ess time
of tPHQV (see the
AC Characteristics
table).
During erase or program modes, RP # low will abort
either erase or program operations , but t he m emory
contents are no longer valid as the data has been
corrupted by the RP# func tion. A s in the read m ode
above, all internal circuitry is turned off to achieve
the power savings.
RP# transitions to VIL, or turning power off to the
device will clear the status register.
3.6 Power-Up/Down Operation
The device is protected against accidental block
erasure or programming during power transitions.
Power supply sequencing is not required, since the
device is indifferent as to which power supply, VPP
or VCC, powers -up firs t. The CUI is res et to t he read
mode after power-up, but the system must drop
CE# low or present a new address to ensure valid
data at the outputs.
A system designer must guard against spurious
writes when VCC voltages are above VLKO and VPP
is activ e. Since both WE# and CE# mus t be low for
a command write, driving either signal to VIH will
inhibit writes to the device. The CUI architecture
provides additional protection since alteration of
memory contents can only occur after successful
completion of the two-step command sequences.
The device is also disabled until RP# is brought to
VIH, regardless of the state of its control inputs. By
holding the device in reset (RP# connected to
system PowerGood) during power-up/down, invalid
bus conditions during power-up can be masked,
providing yet another level of memory protection.
3.6.1 RP# CONNECTED TO SYSTEM
RESET
The use of RP# during system reset is important
with automated write/erase devices because the
system expects to read from the flash memory
when it comes out of reset. If a CPU reset occurs
without a flash memory reset, proper CPU
initialization would not occur because the flash
memory may be providing status information
instead of array data. Intel’s Flash memories allow
proper CPU initialization following a system reset
by connecting the RP# pin to the same RESET#
signal that resets the system CPU.
E4-MBIT SmartVoltage BOOT BLOCK FAMILY
27
SEE NEW DESIGN RECOMMENDATIONS
3.6.2 VCC, VPP AND RP# TRANSITIONS
The CUI latches commands as issued by system
software and is not altered by VPP or CE#
transitions or WSM actions. Its default state upon
power-up, after exit from deep power-down mode,
or after VCC transitions above VLKO (lockout
voltage), is read array mode.
After any word/byte write or bl ock erase operation is
complete and even after VPP transitions down to
VPPLK, the CUI must be reset to read array mode
via the Read Array command if accesses to the
flash memory are desired.
Please refer to Intel’s application note
AP-617
Additional Flash Data Protection Using V
PP
, RP#,
and WP#,
for a circuit-level description of how to
implement the protection discussed in Section 3.6.
3.7 Power Supply Decoupling
Flash memory’s power switching characteristics
require careful device decoupling methods. S ystem
designers should consider three supply current
issues:
1. Standby current levels (ICCS)
2. Active current levels (ICCR)
3. Transient peaks produced by falling and rising
edges of CE#.
Transient c urrent magnit udes depend on the device
outputs’ capacitive and inductive loading. Two-line
control and proper decoupling capacitor selection
will suppress these transient voltage peaks. Each
flash device should have a 0.1 µF ceramic
capacitor connected between each VCC and GND,
and between its VPP and GND. These high-
frequency, inherently low-inductance capacitors
should be placed as close as possible to the
package leads.
3.7.1 VPP TRACE ON PRINTED CIRCUIT
BOARDS
Designing for in-system writes to the flash memory
requires special consideration of the VPP power
supply trace by the printed circuit board designer.
The VPP pin suppl ies t he fl ash mem ory c ells c urrent
for programming and erasing. One should use
simil ar trace widt hs and layout cons iderations giv en
to the VCC power supply trace. Adequate VPP
supply traces, and decoupling capacitors placed
adjacent to the component, will decrease spikes
and overshoots.
NOTE:
Table headings in the DC and AC characteristics tables (i.e., BV-60, BV-80, BV-120, TBV-80, TBE-
120) refer to the specific products listed below. See Section 5.0 for more information on product
naming and line items.
Abbreviation Applicable Product Names
BV-60 E28F004BV-T60, E28F004BV-B60, PA28F400BV-T60, PA28F400BV-B60,
E28F400CV-T60, E28F400CV-B60, E28F400BV-T60, E28F400BV-B60
BV-80 E28F004BV-T80, E28F004BV-B80, PA28F400BV-T80, PA28F400BV-B80,
E28F400CV-T80, E28F400CV-B80, E28F400BV-T80, E28F400BV-B80
BV-120 E28F004BV-T120, E28F004BV-B120, PA28F400BV-T120, PA28F400BV-B120
TBV-80 TE28F004BV-T80, TE28F004BV-B80, TB28F400BV-T80, TB28F400BV-B80,
TE28F400CV-T80, TE28F400CV-B80, TE28F400BV-T80, TE28F400BV-B80
TBE-120 TE28F004BE-T120, TE28F004BE-B120, TE28F400CE-T120, TE28F400CE-B120
4-MBIT SmartVoltage BOOT BLOCK FAMILY E
28 SEE NEW DESIGN RECOMMENDATIONS
4.0 ELECTRICAL SPECIFICATIONS
4.1 Absolute Maximum Ratings*
Commercial Operating Temperature
During Read.............................. 0 °C to +70 °C
During Block Erase
and Word/Byte Program............ 0 °C to +70 °C
Temperature Bias.................. –10 °C to +80 °C
Extended Operating Temperature
During Read.......................... –40 °C to +85 °C
During Block Erase
and Word/Byte Program........ –40 °C to +85 °C
Temperature Under Bias ....... –40 °C to +85 °C
Storage Temperature................. –65 °C to +125 °C
Voltage on Any Pin
(except VCC, VPP, A9 and RP#)
with Respect to GND........... –2.0 V to +7.0 V(2)
Voltage on Pin RP# or Pin A9
with Respect to GND.......–2.0 V to +13.5 V(2,3)
VPP Program Voltage with Respect
to GND during Block Erase
and Word/Byte Program..–2.0 V to +14.0 V(2,3)
VCC Supply Voltage
with Respect to GND........... –2.0 V to +7.0 V(2)
Output Short Circuit Current....................100 mA (4)
NOTICE: This datasheet contains preliminary information on
new products in production. Do not finalize a design with
this information. Revised information will be published when
the product is available. Verify with your local Intel Sales
office that you have the latest datasheet before finalizing a
design.
* WARNING: Stressing the device beyond the "Absolute
Maximum Ratings" may cause permanent damage. These
are stress ratings only. Operation beyond the "Operating
Conditions" is not recommended and extended exposure
beyond the "Operating Conditions" may effect device
reliability.
NOTES:
1. Operating temperature is for commercial product
defined by this specification.
2. Minimum DC voltage is –0.5 V on input/output pins.
During transitions, this level may undershoot to –2.0 V
for periods
<20 ns. Maximum DC voltage on input/output pins is
VCC + 0.5 V which, during transitions, may overshoot to
VCC + 2.0 V for periods <20 ns.
3. Maximum DC voltage on VPP may overshoot to +14.0 V
for periods <20 ns. Maximum DC voltage on RP# or A9
may overshoot to 13.5 V for periods <20 ns.
4. Output shorted for no more than one second. No more
than one output shorted at a time.
4.2 Commercial Operating Conditions
Table 10. Commercial Temperature and VCC Operating Conditions
Symbol Parameter Notes Min Max Units
TAOperating Temperature 0 +70 °C
VCC 3.3 V VCC Supply Voltage (± 0.3 V) 3.0 3.6 Volts
5 V VCC Supply Voltage (10%) 1 4.50 5.50 Volts
5 V VCC Supply Voltage (5%) 2 4.75 5.25 Volts
NOTES:
1. 10% VCC specifications apply to the 60 ns, 80 ns and 120 ns product versions in their standard test configuration.
2. 5% VCC specifications apply to the 60 ns version in its high-speed test configuration.
E4-MBIT SmartVoltage BOOT BLOCK FAMILY
29
SEE NEW DESIGN RECOMMENDATIONS
4.2.1 APPLYING VCC VOLTAGES
When applying VCC voltage to the device, a delay
may be required before initiating device operation,
depending on the VCC ramp rate. If VCC ramps
slower than 1V/100 µs (0.01 V/µs) then no delay is
required. If VCC ramps faster than 1V/100 µs (0.01
V/µs), then a delay of 2 µs is required before
initiating device operation. RP# = GND is
recommended during power-up to protect against
spurious write signals when VCC is between VLKO
and VCCMIN.
VCC Ramp Rate Required Timing
1V/100 µs No delay required.
> 1V/100 µs A delay time of 2 µs is required before any device operation is initiated, including read
operations, command writes, program operations, and erase operations. This delay is
measured beginning from the time VCC reaches VCCMIN (3.0 V for 3.3 ± 0.3 V operation;
and 4.5 V for 5 V operation).
NOTES:
1. These requirements must be strictly followed to guarantee all other read and write specifications.
2. To switch between 3.3 V and 5 V operation, the system should first transition VCC from the existing voltage range to GND,
and then to the new voltage. Any time the VCC supply drops below VCCMIN, the chip may be reset, aborting any operations
pending or in progress.
3. These guidelines must be followed for any VCC transition from GND.
4.3 Capacitance
(TA = 25 °C, f = 1 MHz)
Symbol Parameter Note Typ Max Unit Conditions
CIN Input Capacitance 2 6 8 pF VIN = 0 V
COUT Output Capacitance 1, 2 10 12 pF VOUT = 0 V
NOTES:
1. Sampled, not 100% tested.
2. For the 28F004B, address pin A10 follows the COUT capacitance numbers.
4-MBIT SmartVoltage BOOT BLOCK FAMILY E
30 SEE NEW DESIGN RECOMMENDATIONS
4.4 DC Characteristics—Commercial
Prod BV-60
BV-80
BV-120
Sym Parameter VCC 3.3 ± 0.3 V 5 V ± 10% Unit Test Conditions
Note Typ Max Typ Max
IIL Input Load Current 1 ± 1.0 ± 1.0 µA VCC = VCC Max
VIN = VCC or GND
ILO Output Leakage Current 1 ± 10 ± 10 µA VCC = VCC Max
VIN = VCC or GND
ICCS VCC Standby Current 1,3 0.4 1.5 0.8 2.0 mA VCC = VCC Max
CE# = RP# = BYTE# =
WP# = VIH
60 110 50 130 µA VCC = VCC Max
CE# = RP# = VCC ±
0.2 V
ICCD VCC Deep Power-Down
Current 1 0.2 8 0.2 8 µA VCC = VCC Max
VIN = VCC or GND
RP# = GND ± 0.2 V
ICCR VCC Read Current for
Word or Byte 1,5,6 15 30 50 60 mA CMOS INPUTS
VCC = VCC Max
CE# = GND, OE# = VCC
f = 10 MHz (5 V)
5 MHz (3.3 V)
IOUT = 0 mA, Inputs =
GND ± 0.2 V or VCC
± 0.2 V
15 30 55 65 mA TTL INPUTS
VCC = VCC Max
CE# = VIL, OE# = VIH
f = 10 MHz (5 V)
5 MHz (3.3 V)
IOUT = 0 mA, Inputs =
VIL or VIH
ICCW VCC Program Current for
Word or Byte 1,4 13 30 30 50 mA VPP = VPPH1 (at 5 V)
Program in Progress
10 25 30 45 mA VPP = VPPH2 (at 12 V)
Program in Progress
ICCE VCC Erase Current 1,4 13 30 18 35 mA VPP = VPPH1 (at 5 V)
Block Erase in Progress
10 25 18 30 mA VPP = VPPH2 (at 12 V)
Block Erase in Progress
E4-MBIT SmartVoltage BOOT BLOCK FAMILY
31
SEE NEW DESIGN RECOMMENDATIONS
4.4 DC Characteristics—Commercial (Continued)
Prod BV-60
BV-80
BV-120
Sym Parameter VCC 3.3 ± 0.3 V 5 V ± 10% Unit Test Conditions
Note Typ Max Typ Max
ICCES VCC Erase Suspend
Current 1,2 3 8.0 5 10 mA CE# = VIH
Block Erase Suspend
IPPS VPP Standby Current 1 ± 0.5 ± 15 ± 0.5 ± 10 µA VPP < VPPH2
IPPD VPP Deep Power-Down
Current 1 0.2 5.0 0.2 5.0 µA RP# = GND ± 0.2V
IPPR VPP Read Current 1 50 200 30 200 µA VPP VPPH2
IPPW VPP Program Current for
Word or Byte 1,4 13 30 13 25 mA VPP = VPPH1 (at 5 V)
Program in Progress
825820 V
PP = VPPH2 (at 12 V)
Program in Progress
IPPE VPP Erase Current 1,4 13 30 10 20 mA VPP = VPPH1 (at 5 V)
Block Erase in Progress
825515 V
PP = VPPH2 (at 12 V)
Block Erase in Progress
IPPES VPP Erase
Suspend Current 1 50 200 30 200 µA VPP = VPPH
Block Erase Suspend in
Progress
IRP# RP# Boot Block Unlock
Current 1,4 500 500 µA RP# = VHH
IID A9 Intelligent
Identifier Current 1,4 500 500 µA A9 = VID
4-MBIT SmartVoltage BOOT BLOCK FAMILY E
32 SEE NEW DESIGN RECOMMENDATIONS
4.4 DC Characteristics—Commercial (Continued)
Prod BV-60
BV-80
BV-120
Sym Parameter VCC 3.3 ± 0.3 V 5 V ± 10% Unit Test Conditions
Note Min Max Min Max
VID A9 Intelligent Identifier
Voltage 11.4 12.6 11.4 12.6 V
VIL Input Low Voltage –0.5 0.8 –0.5 0.8 V
VIH Input High Voltage 2.0 VCC +
0.5V 2.0 VCC +
0.5V V
VOL Output Low Voltage 0.45 0.45 V VCC = VCC Min
IOL = 5.8 mA
VOH1 Output High Voltage (TTL) 2.4 2.4 V VCC = VCC Min
IOH = –2.5 mA
VOH2 Output High Voltage (CMOS) 0.85 ×
VCC
0.85 ×
VCC VVCC = VCC Min
IOH = –2.5 mA
VCC
0.4V VCC
0.4V VVCC = VCC Min
IOH = –100 µA
VPPLK VPP Lock-Out Voltage 3 0.0 1.5 0.0 1.5 V Total Write Protect
VPPH1V
PP (Prog/Erase Operations) 4.5 5.5 4.5 5.5 V VPP at 5 V
VPPH2V
PP (Prog/Erase Operations) 11.4 12.6 11.4 12.6 V VPP at 12 V
VLKO VCC Erase/Prog Lock Voltage 7 2.0 2.0 V
VHH RP# Unlock Voltage 11.4 12.6 11.4 12.6 V Boot Block Unlock
NOTES:
1. All currents are in RMS unless otherwise noted. Typical values at VCC = 5.0 V, T = +25 °C. These currents are valid for all
product versions (packages and speeds).
2. ICCES is specified with the device deselected. If the device is read while in erase suspend mode, current draw is the sum of
ICCES and ICCR.
3. Block erases and word/byte writes are inhibited when VPP = VPPLK, and not guaranteed in the range between VPPH1 and
VPPLK.
4. Sampled, not 100% tested.
5. Automatic Power Savings (APS) reduces ICCR to less than 1 mA typical, in static operation.
6. CMOS Inputs are either VCC ± 0.2 V or GND ± 0.2 V. TTL Inputs are either VIL or VIH.
7. For all BV/CV parts, VLKO = 2.0 V for both 3.3 V and 5 V operations.
E4-MBIT SmartVoltage BOOT BLOCK FAMILY
33
SEE NEW DESIGN RECOMMENDATIONS
TEST POINTSINPUT OUTPUT
1.5
3.0
0.0
1.5
NOTE:
AC test inputs are driven at 3.0 V for a logic “1” and 0.0 V for a logic “0.” Input timing begins, and output timing ends, at 1.5 V.
Input rise and fall times (10% to 90%) <10 ns. 0530_12
Figure 12. 3.3 V Inputs and Measurement Points
TEST POINTS
INPUT OUTPUT
2.0
0.8 0.8
2.0
2.4
0.45
NOTE:
AC test inputs are driven at VOH (2.4 VTTL) for a logic “1” and VOL (0.45 VTTL) for a logic “0.” Input timing begins at VIH (2.0 VTTL)
and VIL (0.8 VTTL) . Output timing ends at VIH and VIL. Input rise and fall times (10% to 90%) <10 ns. 0530_13
Figure 13. 5V Inputs and Measurement Points
C
L
OUT
V
CC
DEVICE
UNDER
TEST
R
1
R
2
0530_14
NOTE: See table for component values.
Figure 14. Test Configuration
Test Configuration Component Values
Test Configuration CL (pF) R1 ()R
2
()
3.3 V Standard Test 50 990 770
5 V Standard Test 100 580 390
5 V High-Speed Test 30 580 390
NOTE: CL includes jig capacitance.
4-MBIT SmartVoltage BOOT BLOCK FAMILY E
34 SEE NEW DESIGN RECOMMENDATIONS
4.5 AC Characteristics—Read Only Operations—Commercial
Prod BV-60
Sym Parameter VCC 3.3 ± 0.3 V(5) 5 V ± 5%(6) 5 V ± 10%(7) Unit
Load 50 pF 30 pF 100 pF
Note Min Max Min Max Min Max
tAVAV Read Cycle Time 110 60 70 ns
tAVQV Address to Output Delay 110 60 70 ns
tELQV CE# to Output Delay 2 110 60 70 ns
tPHQV RP# to Output Delay 0.8 0.45 0.45 µs
tGLQV OE# to Output Delay 2 65 30 35 ns
tELQX CE# to Output in Low Z 3 0 0 0 ns
tEHQZ CE# to Output in High Z 3 25 20 20 ns
tGLQX OE# to Output in Low Z 3 0 0 0 ns
tGHQZ OE# to Output in High Z 3 25 20 20 ns
tOH Output Hold from Address,
CE#, or OE# Change,
Whichever Occurs First
3000ns
t
ELFL
tELFH CE# Low to BYTE# High or
Low 3000ns
t
AVFL Address to BYTE# High or
Low 3555ns
t
FLQV
tFHQV BYTE# to Output Delay 3,4 110 60 70 ns
tFLQZ BYTE# Low to Output in
High Z 3452025ns
t
PLPH Reset Pulse Width Low 8 150 60 60 ns
tPLQZ RP# Low to Output High Z 150 60 60 ns
E4-MBIT SmartVoltage BOOT BLOCK FAMILY
35
SEE NEW DESIGN RECOMMENDATIONS
4.5 AC Characteristics—Read Only Operations—Commercial (Continued)
Prod BV-80 BV-120
Sym Parameter VCC 3.3 ± 0.3V(5) 5 V ± 10%(7) 3.3 ± 0.3V(5) 5 V ± 10%(7) Unit
Load 50 pF 100 pF 50 pF 100 pF
Notes Min Max Min Max Min Max Min Max
tAVAV Read Cycle Time 150 80 180 120 ns
tAVQV Address to Output Delay 150 80 180 120 ns
tELQV CE# to Output Delay 2 150 80 180 120 ns
tPHQV RP# to Output Delay 0.8 0.45 0.8 0.45 µs
tGLQV OE# to Output Delay 2 90 40 90 40 ns
tELQX CE# to Output in Low Z 3 0 0 0 0 ns
tEHQZ CE# to Output in High Z 3 25 20 25 20 ns
tGLQX OE# to Output in Low Z 3 0 0 0 0 ns
tGHQZ OE# to Output in High Z 3 25 20 25 20 ns
tOH Output Hold from Address,
CE#, or OE# Change,
Whichever Occurs First
30 0 0 0 ns
t
ELFL
tELFH CE# Low to BYTE# High or
Low 30 0 0 0 ns
t
AVFL Address to BYTE# High or
Low 35555ns
t
FLQV
tFHQV BYTE# to Output Delay 3,4 150 80 180 120 ns
tFLQZ BYTE# Low to Output in
High Z 3 60306030ns
t
PLPH Reset Pulse Width Low 8 150 60 150 60 ns
tPLQZ RP# Low to Output High Z 150 60 150 60
NOTES:
1. See AC Input/Output Reference Waveform for timing measurements.
2. OE# may be delayed up to tCE–tOE after the falling edge of CE# without impact on tCE.
3. Sampled, but not 100% tested.
4. tFLQV, BYTE# switching low to valid output delay will be equal to tAVQV, measured from the time DQ15/A–1 becomes valid.
5. See
Test Configuration
(Figure 14), 3.3 V Standard Test component values.
6. See
Test Configuration
(Figure 14), 5 V High-Speed Test component values.
7. See
Test Configuration
(Figure 14), 5 V Standard Test component values.
8. The specification tPLPH is the minimum time RP# must be held low to produce a valid reset of the device.
4-MBIT SmartVoltage BOOT BLOCK FAMILY E
36 SEE NEW DESIGN RECOMMENDATIONS
Address Stable
Device and
Address Selection
IH
V
IL
V
ADDRESSES (A)
IH
V
IL
V
IH
V
IL
V
IH
V
IL
V
CE# (E)
OE# (G)
WE# (W)
DATA (D/Q)
IH
V
IL
V
RP#(P)
OL
V
OH
V
PHQV
t
High Z Valid Output
Data
Valid Standby
AVAV
t
EHQZ
t
GHQZ
t
OH
t
GLQV
t
GLQX
t
ELQV
t
ELQX
t
AVQV
t
High Z
0530_15
Figure 15. AC Waveforms for Read Operations
Address Stable
Device
Add ress Selection
IH
V
IL
V
ADDRESSES (A)
IH
V
IL
V
IH
V
IL
V
IH
V
IL
V
CE# (E )
OE# (G)
BYTE# (F)
DATA (D/Q)
(DQ0-DQ7)
OL
V
OH
VHigh Z
Data Output
on DQ 0-DQ 7
Data
Valid
Standb y
AVAV
t
EHQZ
t
GHQZ
t
AVQV
t
High Z
GLQV
t
ELQV
t
AVQV
t
OH
t
Data Output
on DQ0-DQ7
DATA (D/Q)
(DQ8-DQ14)
OL
V
OH
VHigh Z
Data Output
on DQ 8- DQ14
High Z
(DQ15/A-1)
OL
V
OH
VHigh Z High Z
Data Output
on DQ15 Address Input
FLQZ
t
ELQX
t
ELFL
t
AVFL
t
GLQX
t
0530_16
Figure 16. BYTE# Timing Diagram for Read Operations
E4-MBIT SmartVoltage BOOT BLOCK FAMILY
37
SEE NEW DESIGN RECOMMENDATIONS
4.6 AC Characteristics—WE# Controlled Write Operations(1)—Commercial
Prod BV-60
Sym Parameter VCC 3.3 ± 0.3 V(9) 5 V ± 5%(10) 5 V ± 10%(10) Unit
Load 50 pF 30 pF 100 pF
Note Min Max Min Max Min Max
tAVAV Write Cycle Time 110 60 70 ns
tPHWL RP# Setup to WE# Going Low 0.8 0.45 0.45 µs
tELWL CE# Setup to WE# Going Low 0 0 0 ns
tPHHWH Boot Block Lock Setup to WE#
Going High 6,8 200 100 100 ns
tVPWH VPP Setup to WE# Going High 5,8 200 100 100 ns
tAVWH Address Setup to WE# Going
High 3905050ns
t
DVWH Data Setup to WE# Going High 4 90 50 50 ns
tWLWH WE# Pulse Width 90 50 50 ns
tWHDX Data Hold Time from WE# High 4 0 0 0 ns
tWHAX Address Hold Time from WE#
High 3000ns
t
WHEH CE# Hold Time from WE# High 0 0 0 ns
tWHWL WE# Pulse Width High 20 10 20 ns
tWHQV1 Duration of Word/Byte Program 2,5 6 6 6 µs
tWHQV2 Duration of Erase (Boot) 2,5,6 0.3 0.3 0.3 s
tWHQV3 Duration of Erase (Parameter) 2,5 0.3 0.3 0.3 s
tWHQV4 Duration of Erase (Main) 2,5 0.6 0.6 0.6 s
tQVVL VPP Hold from Valid SRD 5,8 0 0 0 ns
tQVPH RP# VHH Hold from Valid SRD 6,8 0 0 0 ns
tPHBR Boot-Block Lock Delay 7,8 200 100 100 ns
4-MBIT SmartVoltage BOOT BLOCK FAMILY E
38 SEE NEW DESIGN RECOMMENDATIONS
4.6 AC Characteristics—WE# Controlled Write Operations(1)—Commercial
(Continued)
Prod BV-80 BV-120
Sym Parameter VCC 3.3 ±0.3V(9) 5 V±10%(11) 3.3 ± 0.3V(9) 5 V±10%(11) Unit
Load 50 pF 100 pF 50 pF 100 pF
Notes Min Max Min Max Min Max Min Max
tAVAV Write Cycle Time 150 80 180 120 ns
tPHWL RP# Setup to WE# Going
Low 0.8 0.45 0.8 0.45 µs
tELWL CE# Setup to WE# Going
Low 0000ns
t
PHHWH Boot Block Lock Setup to
WE# Going High 6,8 200 100 200 100 ns
tVPWH VPP Setup to WE# Going
High 5,8 200 100 200 100 ns
tAVWH Address Setup to WE#
Going High 3 120 50 150 50 ns
tDVWH Data Setup to WE# Going
High 4 120 50 150 50 ns
tWLWH WE# Pulse Width 120 50 150 50 ns
tWHDX Data Hold Time from
WE# High 40 0 0 0 ns
t
WHAX Address Hold Time from
WE# High 30 0 0 0 ns
t
WHEH CE# Hold Time from WE#
High 0000ns
t
WHWL WE# Pulse Width High 30 30 30 30 ns
tWHQV1 Word/Byte Program Time 2,5 6 6 6 6 µs
tWHQV2 Erase Duration (Boot) 2,5,6 0.3 0.3 0.3 0.3 s
tWHQV3 Erase Duration (Param) 2,5 0.3 0.3 0.3 0.3 s
tWHQV4 Erase Duration (Main) 2,5 0.6 0.6 0.6 0.6 s
tQVVL VPP Hold from Valid SRD 5,8 0 0 0 0 ns
tQVPH RP# VHH Hold from Valid
SRD 6,8 0 0 0 0 ns
tPHBR Boot-Block Lock Delay 7,8 200 100 200 100 ns
E4-MBIT SmartVoltage BOOT BLOCK FAMILY
39
SEE NEW DESIGN RECOMMENDATIONS
NOTES:
1. Read timing characteristics during write and erase operations are the same as during read-only operations. Refer to
AC
Characteristics
during read mode.
2. The on-chip WSM completely automates program/erase operations; program/erase algorithms are now controlled internally
which includes verify and margining operations.
3. Refer to command definition table for valid AIN. (Table 7)
4. Refer to command definition table for valid DIN. (Table 7)
5. Program/erase durations are measured to valid SRD data (successful operation, SR.7 = 1).
6. For boot block program/erase, RP# should be held at VHH or WP# should be held at VIH until operation completes
successfully.
7. Time tPHBR is required for successful locking of the boot block.
8. Sampled, but not 100% tested.
9. See
Test Configuration
(Figure 14), 3.3 V Standard Test component values.
10. See
Test Configuration
(Figure 14), 5 V High-Speed Test component values.
11. See
Test Configuration
(Figure 14), 5 V Standard Test component values.
ADDRESSES (A)
CE# (E)
OE# (G)
WE# (W)
DATA (D/Q)
RP# (P)
IH
V
IL
V
IH
V
IL
V
IH
V
IL
V
IH
V
IL
V
HH
V
6.5V
IL
V
IL
V
IN
D
IN
A
IN
A
WHEH
t
WHWL
t
Valid
SRD
IN
D
WHQV1,2,3,4
t
PHHWH
t
IH
V
PHWL
t
High Z
WHDX
t
IH
V
IL
V
V (V)
PP
12 3 4 65
PPH
V
PPLK
V
PPH
V1
2
WP#
IL
V
IH
V
AVAV
t
AVWH
t
WHAX
t
DVWH
t
WLWH
t
QVPH
t
QVVL
t
VPWH
t
IN
D
ELWL
t
0530_17
NOTES:
1. VCC Power-Up and Standby.
2. Write Program or Erase Setup Command.
3. Write Valid Address and Data (Program) or Erase Confirm Command.
4. Automated Program or Erase Delay.
5. Read Status Register Data.
6. Write Read Array Command.
Figure 17. AC Waveforms for Write Operations (WE#–Controlled Writes)
4-MBIT SmartVoltage BOOT BLOCK FAMILY E
40 SEE NEW DESIGN RECOMMENDATIONS
4.7 AC Characteristics—CE# Controlled Write Operations(1, 12)—Commercial
Prod BV-60
Sym Parameter VCC 3.3 ± 0.3 V(9) 5 V ± 5%(10) 5 V ± 10%(11) Unit
Load 50 pF 30 pF 100 pF
Note Min Max Min Max Min Max
tAVAV Write Cycle Time 110 60 70 ns
tPHEL RP# High Recovery to CE#
Going Low 0.8 0.45 0.45 µs
tWLEL WE# Setup to CE# Going Low 0 0 0 ns
tPHHEH Boot Block Lock Setup to CE#
Going High 6,8 200 100 100 ns
tVPEH VPP Setup to CE# Going High 5,8 200 100 100 ns
tAVEH Address Setup to CE# Going
High 3905050ns
t
DVEH Data Setup to CE# Going High 4 90 50 50 ns
tELEH CE# Pulse Width 90 50 50 ns
tEHDX Data Hold Time from CE# High 4 0 0 0 ns
tEHAX Address Hold Time from CE#
High 3000ns
t
EHWH WE # Hold Time from CE# High 0 0 0 ns
tEHEL CE# Pulse Width High 20 10 20 ns
tEHQV1 Duration of Word/Byte
Programming Operation 2,5 6 6 6 µs
tEHQV2 Erase Duration (Boot) 2,5,6 0.3 0.3 0.3 s
tEHQV3 Erase Duration (Param) 2,5 0.3 0.3 0.3 s
tEHQV4 Erase Duration(Main) 2,5 0.6 0.6 0.6 s
tQVVL VPP Hold from Valid SRD 5,8 0 0 0 ns
tQVPH RP# VHH Hold from
Valid SRD 6,8 0 0 0 ns
tPHBR Boot-Block Lock Delay 7,8 200 100 100 ns
E4-MBIT SmartVoltage BOOT BLOCK FAMILY
41
SEE NEW DESIGN RECOMMENDATIONS
4.7 AC Characteristics—CE# Controlled Write Operations(1, 12)—Commercial
(Continued)
Prod BV-80 BV-120
Sym Parameter VCC 3.3 ± 0.3V(9) 5V±10%(11) 3.3 ± 0.3V(9) 5V±10%(11) Unit
Load 50 pF 100 pF 50 pF 100 pF
Notes Min Max Min Max Min Max Min Max
tAVAV Write Cycle Time 150 80 180 120 ns
tPHEL RP# High Recovery to
CE# Going Low 0.8 0.45 0.8 0.45 µs
tWLEL WE# Setup to CE# Going
Low 0000ns
t
PHHEH Boot Block Lock Setup to
CE# Going High 6,8 200 100 200 100 ns
tVPEH VPP Setup to CE# Going
High 5,8 200 100 200 100 ns
tAVEH Address Setup to CE#
Going High 3 120 50 150 50 ns
tDVEH Data Setup to CE# Going
High 4 120 50 150 50 ns
tELEH CE# Pulse Width 120 50 150 50 ns
tEHDX Data Hold Time from CE#
High 40 0 0 0 ns
t
EHAX Address Hold Time from
CE# High 30 0 0 0 ns
t
EHWH WE # Hold Time from
CE# High 0000ns
t
EHEL CE# Pulse Width High 30 30 30 30 ns
tEHQV1 Duration of Word/Byte
Programming Operation 2,56666µs
tEHQV2 Erase Duration (Boot) 2,5,6 0.3 0.3 0.3 0.3 s
tEHQV3 Erase Duration (Param) 2,5 0.3 0.3 0.3 0.3 s
tEHQV4 Erase Duration(Main) 2,5 0.6 0.6 0.6 0.6 s
tQVVL VPP Hold from Valid SRD 5,8 0 0 0 0 ns
tQVPH RP# VHH Hold from
Valid SRD 6,8 0 0 0 0 ns
tPHBR Boot-Block Lock Delay 7,8 200 100 200 100 ns
4-MBIT SmartVoltage BOOT BLOCK FAMILY E
42 SEE NEW DESIGN RECOMMENDATIONS
NOTES:
See
AC Characteristics—WE# Controlled Write Operations
for notes 1 through 11.
12. Chip-Enable controlled writes: write operations are driven by the valid combination of CE# and WE# in systems where
CE# defines the write pulse-width (within a longer WE# timing waveform), all set-up, hold and inactive WE# times should
be measured relative to the CE# waveform.
ADDRESSES (A)
WE # (W)
OE# (G)
CE# (E)
DATA (D/Q)
RP# (P)
IH
V
IL
V
IH
V
IL
V
IH
V
IL
V
IH
V
IL
V
HH
V
6.5V
IL
V
IN
D
IN
A
IN
A
AVAV
t
Valid
SRD
IN
D
QVPH
t
PHHEH
t
High Z
EHDX
t
IH
V
IL
V
V (V)
PP
12 3 4 65
EHAX
t
EHQV1,2,3,4
t
EHEL
t
EHWH
t
ELEH
t
DVEH
t
VPEH
t
QVVL
t
PHEL
t
WLEL
t
AVEH
t
PPLK
V
PPH
V1
2
PPH
V
IL
V
IH
V
IL
V
IH
V
WP#
IN
D
0530_18
NOTES:
1. VCC Power-Up and Standby.
2. Write Program or Erase Setup Command.
3. Write Valid Address and Data (Program) or Erase Confirm Command.
4. Automated Program or Erase Delay.
5. Read Status Register Data.
6. Write Read Array Command.
Figure 18. Alternate AC Waveforms for Write Operations (CE#–Controlled Writes)
E4-MBIT SmartVoltage BOOT BLOCK FAMILY
43
SEE NEW DESIGN RECOMMENDATIONS
4.8 Erase and Program Timings—Commercial
TA = 0 °C to +70 °C
VPP 5 V ± 10% 12 V ± 5%
VCC 3.3 ± 0.3 V 5 V ± 10% 3.3 ± 0.3 V 5 V ± 10%
Parameter Typ Max Typ Max Typ Max Typ Max Unit
Boot/Parameter Block Erase Time 0.84 7 0.8 7 0.44 7 0.34 7 s
Main Block Erase Time 2.4 14 1.9 14 1.3 14 1.1 14 s
Main Block Program Time (Byte) 1.7 1.8 1.6 1.2 s
Main Block Program Time (Word) 1.1 0.9 0.8 0.6 s
Byte Program Time(4) 10 10 8 8 µs
Word Program Time(4) 13 13 8 8 µs
NOTES:
1. All numbers are sampled, not 100% tested.
2. Max erase times are specified under worst case conditions. The max erase times are tested at the same value
independent of VCC and VPP. See Note 3 for typical conditions.
3. Typical conditions are +25 °C with VCC and VPP at the center of the specified voltage range. Production programming using
VCC = 5.0 V, VPP = 12.0 V typically results in a 60% reduction in programming time.
4. Contact your Intel field representative for more information.
4.9 Extended Operating Conditions
Table 11. Extended Temperature and VCC Operating Conditions
Symbol Parameter Notes Min Max Units
TAOperating Temperature –40 +85 °C
VCC 2.7 V–3.6 V VCC Supply Voltage 1 2.7 3.6 Volts
3.3 V VCC Supply Voltage (± 0.3 V) 1 3.0 3.6 Volts
5 V VCC Supply Voltage (10%) 2 4.50 5.50 Volts
NOTES:
1. AC specifications are valid at both voltage ranges. See
DC Characteristics
tables for voltage range-specific specifications.
2. 10% VCC specifications apply to 80 ns and 120 ns versions in their standard test configuration.
4-MBIT SmartVoltage BOOT BLOCK FAMILY E
44 SEE NEW DESIGN RECOMMENDATIONS
4.9.1 APPLYING VCC VOLTAGES
When applying VCC voltage to the device, a delay
may be required before initiating device operation,
depending on the VCC ramp rate. If VCC ramps
slower than 1V/100 µs (0.01 V/µs) then no delay is
required. If VCC ramps faster than 1V/100 µs (0.01
V/µs), then a delay of 2 µs is required before
initiating device operation. RP# = GND is
recommended during power-up to protect against
spurious write signals when VCC is between VLKO
and VCCMIN.
VCC Ramp Rate Required Timing
1V/100 µs No delay required.
> 1V/100 µs A delay time of 2 µs is required before any device operation is initiated, including read
operations, command writes, program operations, and erase operations. This delay is
measured beginning from the time VCC reaches VCCMIN (2.7 V for 2.7 V–3.6 V
operation, 3.0 V for 3.3 ± 0.3 V operation; and 4.5 V for 5 V operation).
NOTES:
1. These requirements must be strictly followed to guarantee all other read and write specifications.
2. To switch between 3.3 V and 5 V operation, the system should first transition VCC from the existing voltage range to GND,
and then to the new voltage. Any time the VCC supply drops below VCCMIN, the chip may be reset, aborting any operations
pending or in progress.
3. These guidelines must be followed for any VCC transition from GND.
4.10 Capacitance
(TA = 25 °C, f = 1 MHz)
Symbol Parameter Note Typ Max Unit Conditions
CIN Input Capacitance 1 6 8 pF VIN = 0 V
COUT Output Capacitance 1 10 12 pF VOUT = 0 V
NOTE:
1. Sampled, not 100% tested.
E4-MBIT SmartVoltage BOOT BLOCK FAMILY
45
SEE NEW DESIGN RECOMMENDATIONS
4.11 DC Characteristics—Extended Temperature Operations
Prod TBE-120 TBV-80 TBV-80
TBE-120
Sym Parameter VCC 2.7 V–3.6 V 3.3 ± 0.3 V 5 V ± 10% Unit Test Conditions
Notes Typ Max Typ Max Typ Max
IIL Input Load
Current 1± 1.0 ± 1.0 ± 1.0 µA VCC = VCCMax
VIN = VCC or GND
ILO Output
Leakage
Current
1 ± 10 ± 10 ± 10 µA VCC = VCC Max
VIN = VCC or GND
ICCS VCC
Standby
Current
1,3 50 110 60 110 70 150 µA CMOS Levels
VCC = VCC Max
CE# = RP# = WP# =
VCC ± 0.2 V
0.4 1.5 0.4 1.5 0.8 2.5 mA TTL Levels
VCC = VCC Max
CE# = RP# = BYTE#
= VIH
ICCD VCC Deep
Power-
Down
Current
1 0.2 8 0.2 8 0.2 8 µA VCC = VCC Max
VIN = VCC or GND
RP# = GND ± 0.2 V
ICCR VCC Read
Current for
Word or
Byte
1,5,6 14 30 15 30 50 65 mA CMOS INPUTS
VCC = VCC Max
CE = VIL
f = 10 MHz (5 V)
5 MHz (3.3 V)
IOUT = 0 mA
Inputs = GND ± 0.2 V
or VCC ± 0.2 V
14 30 15 30 55 70 mA TTL INPUTS
VCC = VCC Max
CE# = VIL
f = 10 MHz (5 V),
5 MHz (3.3 V)
IOUT = 0 mA
Inputs = VIL or VIH
4-MBIT SmartVoltage BOOT BLOCK FAMILY E
46 SEE NEW DESIGN RECOMMENDATIONS
4.11 DC Characteristics—Extended Temperature Operations (Continued)
Prod TBE-120 TBV-80 TBV-80
TBE-120
Sym Parameter VCC 2.7 V–3.6 V 3.3 ± 0.3 V 5 V ± 10% Unit Test Conditions
Notes Typ Max Typ Max Typ Max
ICCW VCC
Program
Current
1,4 8 3013303050mA
V
PP
= VPPH1 (at 5 V)
Program in Progress
for Word or
Byte 9 2510253045mA
V
PP
= VPPH2 (at 12 V)
Program in Progress
ICCE VCC Erase
Current 1,4 12 30 13 30 22 45 mA V
PP
= VPPH1 (at 5 V)
Erase in Progress
9 2510251840mA
V
PP
= VPPH2 (at 12 V)
Erase in Progress
ICCES VCC Erase
Suspend
Current
1,2 2.5 8.0 3 8.0 5 12.0 mA CE# = VIH
VPP = VPPH1 (at 5 V)
Block Erase Suspend
IPPS VPP
Standby
Current
1± 5 ± 15 ± 5 ± 15 ± 5 ± 15 µA VPP < VPPH2
IPPD VPP Deep
Power-
Down
Current
1 0.2 10 0.2 10 0.2 10 µA RP# = GND ± 0.2 V
IPPR VPP Read
Current 1 50 200 50 200 50 200 µA VPP VPPH2
IPPW VPP
Program 1,4 13 30 13 30 13 30 mA V
PP
= VPPH1 (at 5 V)
Program in Progress
Current for
Word/Byte 8 25 8 25 8 25 mA V
PP
= VPPH2 (at 12 V)
Program in Progress
E4-MBIT SmartVoltage BOOT BLOCK FAMILY
47
SEE NEW DESIGN RECOMMENDATIONS
4.11 DC Characteristics—Extended Temperature Operations (Continued)
Prod TBE-120 TBV-80 TBV-80
TBE-120
Sym Parameter VCC 2.7 V–3.6 V 3.3 ± 0.3 V 5 V ± 10% Unit Test Conditions
Notes Typ Max Typ Max Typ Max
IPPE VPP Erase
Current 1,4 13 30 13 30 15 25 mA V
PP
= VPPH1 (at 5 V)
Block Erase in
Progress
8 25 8 25 10 20 mA V
PP
= VPPH2 (at 12 V)
Block Erase in
Progress
IPPES VPP Erase
Suspend
Current
1 50 200 50 200 50 200 µA VPP = VPPH
Block Erase Suspend
in Progress
IRP# RP# Boot
Block
Unlock
Current
1,4 500 500 500 µA RP# = VHH
V
PP
= 12 V
IID A9
Intelligent
Identifier
Current
1,4 500 500 500 µA A9 = VID
4-MBIT SmartVoltage BOOT BLOCK FAMILY E
48 SEE NEW DESIGN RECOMMENDATIONS
4.11 DC Characteristics—Extended Temperature Operations (Continued)
Prod TBE-120 TBV-80 TBV-80
TBE-120
Sym Parameter VCC 2.7 V–3.6 V 3.3 ± 0.3 V 5 V ± 10% Unit Test Conditions
Notes Min Max Min Max Min Max
VID A9
Intelligent
Identifier
Voltage
11.4 12.6 11.4 12.6 11.4 12.6 V
VIL Input Low
Voltage –0.5 0.8 –0.5 0.8 –0.5 0.8 V
VIH Input High
Voltage 2.0 VCC
±
0.5V
2.0 VCC
±
0.5V
2.0 VCC
±
0.5V
V
VOL Output Low
Voltage 0.45 0.45 0.45 V VCC = VCC Min
IOL = 5.8 mA (5 V)
2 mA (3.3 V)
VPP = 12 V
VOH1 Output
High
Voltage
(TTL)
2.4 2.4 2.4 V VCC = VCC Min
IOH = –2.5 mA
VOH2 Output
High
Voltage
0.85
×
VCC
0.85
×
VCC
0.85
×
VCC
VVCC = VCC Min
IOH = –2.5 mA
(CMOS) VCC
0.4V
VCC
0.4V
VCC
0.4V
VVCC = VCC Min
IOH = –100 µA
VPPLK VPP
Lock-Out
Voltage
3 0.0 1.5 0.0 1.5 0.0 1.5 V Complete Write
Protection
VPPH1VPP during
Prog/Erase 4.5 5.5 4.5 5.5 4.5 5.5 V VPP at 5 V
VPPH2Operations 11.4 12.6 11.4 12.6 11.4 12.6 V VPP at 12 V
VLKO VCC
Erase/Write
Lock
Voltage
8 2.0 2.0 2.0 V
VHH RP#
Unlock
Voltage
11.4 12.6 11.4 12.6 11.4 12.6 V V
PP
= 12 V
Boot Block Write/
Erase
E4-MBIT SmartVoltage BOOT BLOCK FAMILY
49
SEE NEW DESIGN RECOMMENDATIONS
NOTES:
1. All currents are in RMS unless otherwise noted. Typical values at VCC = 5.0 V, T = +25 °C. These currents are valid for all
product versions (packages and speeds).
2. ICCES is specified with device de-selected. If device is read while in erase suspend, current draw is sum of I
CCES and ICCR.
3. Block erases and word/byte programs inhibited when VPP = VPPLK, and not guaranteed in the range between VPPH1 and
VPPLK.
4. Sampled, not 100% tested.
5. Automatic Power Savings (APS) reduces ICCR to less than 1 mA typical, in static operation.
6. CMOS Inputs are either VCC ± 0.2 V or GND ± 0.2 V. TTL Inputs are either VIL or VIH.
7. For the 28F004B address pin A10 follows the COUT capacitance numbers.
8. For all BV/CV/BE/CE parts, VLKO = 2.0 V for 2.7 V, 3.3 V and 5.0 V operations.
4-MBIT SmartVoltage BOOT BLOCK FAMILY E
50 SEE NEW DESIGN RECOMMENDATIONS
TEST POINTSINPUT OUTPUT
1.35
2.7
0.0
1.35
0530_19
NOTE:
AC test inputs are driven at 2.7 V for a logic “1” and 0.0 V for a logic “0.” Input timing begins, and output timing ends, at 1.35 V.
Input rise and fall times (10% to 90%) <10 ns.
Figure 19. 2.7 V–3.6 V Input Range and Measurement Points
TEST POINTSINPUT OUTPUT
1.5
3.0
0.0
1.5
0530_12
NOTE:
AC test inputs are driven at 3.0 V for a logic “1” and 0.0 V for a logic “0.” Input timing begins, and output timing ends, at 1.5 V.
Input rise and fall times (10% to 90%) <10 ns.
Figure 20. 3.3 V Input Range and Measurement Points
TEST POINTS
INPUT OUTPUT
2.0
0.8 0.8
2.0
2.4
0.45
0530_13
NOTE:
AC test inputs are driven at VOH (2.4 VTTL) for a logic “1” and VOL (0.45 VTTL) for a logic “0.” Input timing begins at VIH (2.0 VTTL)
and VIL (0.8 VTTL). Output timing ends at VIH and VIL. Input rise and fall times (10% to 90%) < 10 ns.
Figure 21. 5 V Input Range and Measurement Points
C
L
OUT
V
CC
DEVICE
UNDER
TEST
R
1
R
2
0530_14
NOTE: See table for component values.
Figure 22. Test Configuration
Test Configuration Component Values
Test Configuration CL (pF) R1 ()R
2
()
2.7 V and 3.3 V
Standard Test 50 990 770
5 V Standard Test 100 580 390
NOTE: CL includes jig capacitance.
E4-MBIT SmartVoltage BOOT BLOCK FAMILY
51
SEE NEW DESIGN RECOMMENDATIONS
4.12 AC Characteristics—Read Only Operations(1)—Extended Temperature
Prod TBE-120 TBV-80 TBV-80
TBE-120
Sym Parameter VCC 2.7V–3.6V(5) 3.3 ±0.3V(5) 5V±10%(6) Unit
Load 50 pF 50 pF 100 pF
Notes Min Max Min Max Min Max
tAVAV Read Cycle Time 120 110 80 ns
tAVQV Address to Output Delay 120 110 80 ns
tELQV CE# to Output Delay 2 120 110 80 ns
tPHQV RP# to Output Delay 0.8 0.8 0.45 µs
tGLQV OE# to Output Delay 2 65 65 40 ns
tELQX CE# to Output in Low Z 3 0 0 0 ns
tEHQZ CE# to Output in High Z 3 25 25 20 ns
tGLQX OE# to Output in Low Z 3 0 0 0 ns
tGHQZ OE# to Output in High Z 3 25 25 20 ns
tOH Output Hold from Address, CE#,
or OE# Change, Whichever
Occurs First
30 0 0 ns
t
ELFL
tELFH CE# Low to BYTE# High or Low 3 5 5 5 ns
tAVFL Address to BYTE# High or Low 3 0 0 0 ns
tFLQV
tFHQV
BYTE# to Output Delay 3,4 120 110 80 ns
tFLQZ BYTE# Low to Output in High Z 3 45 45 30 ns
tPLPH Reset Pulse Width Low 7 150 150 60 ns
tPLQZ RP# Low to Output High Z 150 150 60 ns
NOTES:
1. See AC Input/Output Reference Waveform for timing measurements.
2. OE# may be delayed up to tCE–tOE after the falling edge of CE# without impact on tCE.
3. Sampled, but not 100% tested.
4. tFLQV, BYTE# switching low to valid output delay will be equal to tAVQV, measured from the time DQ15/A–1 becomes valid.
5. See
Test Configuration
(Figure 22), 2.7 V–3.6 V and 3.3 ± 0.3 V Standard Test component values.
6. See
Test Configuration
(Figure 22), 5 V Standard Test component values.
7. The specification tPLPH is the minimum time RP# must be held low to produce a valid reset of the device.
4-MBIT SmartVoltage BOOT BLOCK FAMILY E
52 SEE NEW DESIGN RECOMMENDATIONS
4.13 AC Characteristics— WE#-Controlled Write Operations(1)
Extended Temperature
Prod TBE-120 TBV-80 TBV-80
TBE-120
Sym Parameter VCC 2.7V–3.6V(9) 3.3±0.3V(9) 5V±10%(10) Unit
Load 50 pF 50 pF 100 pF
Notes Min Max Min Max Min Max
tAVAV Write Cycle Time 120 110 80 ns
tPHWL RP# High Recovery to WE#
Going Low 0.8 0.8 0.45 µs
tELWL CE# Setup to WE# Going Low 0 0 0 ns
tPHHWH Boot Block Lock Setup to WE#
Going High 6,8 200 200 100 ns
tVPWH VPP Setup to WE#
Going High 5,8 200 200 100 ns
tAVWH Address Setup to WE# Going
High 3909060 ns
t
DVWH Data Setup to WE# Going High 4 70 70 60 ns
tWLWH WE# Pulse Width 90 90 60 ns
tWHDX Data Hold Time from WE# High 4 0 0 0 ns
tWHAX Address Hold Time from WE#
High 3000ns
t
WHEH CE# Hold Time from WE# High 0 0 0 ns
tWHWL WE# Pulse Width High 30 20 20 ns
tWHQV1 Word/Byte Program Time 2,5,8 6 6 6 µs
tWHQV2 Erase Duration (Boot) 2,5,
6, 8 0.3 0.3 0.3 s
tWHQV3 Erase Duration (Param) 2,5,8 0.3 0.3 0.3 s
tWHQV4 Erase Duration (Main) 2,5,8 0.6 0.6 0.6 s
tQVVL VPP Hold from Valid SRD 5,8 0 0 0 ns
tQVPH RP# VHH Hold from Valid SRD 6,8 0 0 0 ns
tPHBR Boot-Block Lock Delay 7,8 200 200 100 ns
E4-MBIT SmartVoltage BOOT BLOCK FAMILY
53
SEE NEW DESIGN RECOMMENDATIONS
NOTES:
1. Read timing characteristics during program and erase operations are the same as during read-only operations. Refer to AC
Characteristics during read mode.
2. The on-chip WSM completely automates program/erase operations; program/erase algorithms are now controlled internally
which includes verify and margining operations.
3. Refer to command definition table for valid AIN. (Table 7)
4. Refer to command definition table for valid DIN. (Table 7)
5. Program/erase durations are measured to valid SRD data (successful operation, SR.7 = 1)
6. For boot block program/erase, RP# should be held at VHH or WP# should be held at VIH until operation completes
successfully.
7. Time tPHBR is required for successful locking of the boot block.
8. Sampled, but not 100% tested.
9. See
Test Configuration
(Figure 22), 2.7 V–3.6 V and 3.3 ± 0.3 V Standard Test component values.
10. See
Test Configuration
(Figure 22), 5 V Standard Test component values.
4-MBIT SmartVoltage BOOT BLOCK FAMILY E
54 SEE NEW DESIGN RECOMMENDATIONS
4.14 AC Characteristics—CE#-Controlled Write Operations(1, 11)—Extended
Temperature
Prod TBE-120 TBV-80 TBV-80
TBE-120
Sym Parameter VCC 2.7V–3.6V(9) 3.3 ±0.3V(9) 5V±10%(10) Unit
Load 50 pF 50 pF 100 pF
Notes Min Max Min Max Min Max
tAVAV Write Cycle Time 120 110 80 ns
tPHEL RP# High Recovery to CE#
Going Low 0.8 0.8 0.45 µs
tWLEL WE# Setup to CE# Going Low 0 0 0 ns
tPHHEH Boot Block Lock Setup to CE#
Going High 6,8 200 200 100 ns
tVPEH VPP Setup to CE# Going High 5,8 200 200 100 ns
tAVEH Address Setup to CE# Going
High 90 90 60 ns
tDVEH Data Setup to CE# Going High 3 70 70 60 ns
tELEH CE# Pulse Width 4 90 90 60 ns
tEHDX Data Hold Time from CE# High 0 0 0 ns
tEHAX Address Hold Time from CE#
High 40 0 0 ns
t
EHWH WE# Hold Time from CE# High 3 0 0 0 ns
tEHEL CE# Pulse Width High 20 20 20 ns
tEHQV1 Word/Byte Program Time 2,5 6 6 6 µs
tEHQV2 Erase Duration (Boot) 2,5,6 0.3 0.3 0.3 s
tEHQV3 Erase Duration (Param) 2,5 0.3 0.3 0.3 s
tEHQV4 Erase Duration (Main) 2,5 0.6 0.6 0.6 s
tQVVL VPP Hold from Valid SRD 5,8 0 0 0 ns
tQVPH RP# VHH Hold from Valid SRD 6,8 0 0 0 ns
tPHBR Boot-Block Lock Delay 7,8 200 200 100 ns
NOTES:
See
WE# Controlled Write Operations
for notes 1 through 10.
11. Chip-Enable controlled writes: write operations are driven by the valid combination of CE# and WE# in systems where CE#
defines the write pulse-width (within a longer WE# timing waveform), all set-up, hold and inactive WE# times should be
measured relative to the CE# waveform.
E4-MBIT SmartVoltage BOOT BLOCK FAMILY
55
SEE NEW DESIGN RECOMMENDATIONS
4.15 Erase and Program Timings—Extended Temperature
TA = –40 °C to +85 °C
VPP 5 V ± 10% 12 V ± 5%
VCC 2.7 V–3.6 V 3.3 ± 0.3 V 5 V ± 10% 2.7 V–3.6 V 3.3 ± 0.3 V 5 V ± 10%
Parameter Typ Max Typ Max Typ Max Typ Max Typ Max Typ Max Unit
Boot/Parameter
Block Erase Time 0.88 7 0.84 7 0.8 7 0.46 7 0.44 7 0.34 7 s
Main Block
Erase Time 2.5 14 2.4 14 1.9 14 1.36 14 1.3 14 1.1 14 s
Main Block
Program Time
(Byte Mode)
1.87 1.7 1.4 1.76 1.6 1.2 s
Main Block
Program Time
(Word Mode)
1.21 1.1 0.9 0.88 0.8 0.6 s
Byte Program
Time(4) 11 10 10 8.8 88µs
Word Program
Time(4) 14.3 13 13 8.8 88µs
NOTES:
1. All numbers are sampled, not 100% tested.
2. Max erase times are specified under worst case conditions. The max erase times are tested at the same value
independent of VCC and VPP. See Note 3 for typical conditions.
3. Typical conditions are +25 °C with VCC and VPP at the center of the specified voltage range. Production programming using
VCC = 5.0 V, VPP = 12.0 V typically results in a 60% reduction in programming time.
4. Contact your Intel field representative for more information.
4-MBIT SmartVoltage BOOT BLOCK FAMILY E
56 SEE NEW DESIGN RECOMMENDATIONS
5.0 ORDERING INFORMATION
Product line designator
for all Intel Flash products
Densi t y / Or gan i za t ion
00X = x8- only ( X = 1, 2, 4, 8)
X00 = x8/x16 Select able (X = 2, 4, 8)
Access Speed(ns)
BV/CV: VCC = 5V
BE/CE: VCC = 2.7V
Architecture
B = Boot Block
C = Compact 48-Lead TSOP
Boot Block
Operat ing Temperat ure
T = Extended Temp
Blank = Commercial Temp
Package
E = TSOP
PA = 44-Lead PSOP
TB = Ext. Temp 44-Lead PSOP
E28F4 00 CV- T 08
T = Top Boot
B = Bottom Boot
Voltag e Options (V PP/VCC)
V = (5 or 12 / 3.3 or 5)
E = (5 or 12 / 2.7 or 5)
T
0530_23
VALID COMBINATIONS:
40-Lead TSOP 44-Lead PSOP 48-Lead TSOP 56-Lead TSOP
Commercial E28F004BVT60 PA28F400BVT60 E28F400CVT60 E28F400BVT60
E28F004BVB60 PA28F400BVB60 E28F400CVB60 E28F400BVB60
E28F004BVT80 PA28F400BVT80 E28F400CVT80 E28F400BVT80
E28F004BVB80 PA28F400BVB80 E28F400CVB80 E28F400BVB80
E28F004BVT120 PA28F400BVT120
E28F004BVB120 PA28F400BVB120
Extended TE28F004BVT80 TB28F400BVT80 TE28F400CVT80 TE28F400BVT80
TE28F004BVB80 TB28F400BVB80 TE28F400CVB80 TE28F400BVB80
TE28F004BET120 TE28F400CET120
TE28F004BEB120 TE28F400CEB120
Summary of Line Items
VCC VPP 40-Ld 44-Ld 48-Ld 56-Ld 0 °C – –40 °C –
Name 2.7 V 3.3 V 5 V 5 V 1 2V TSOP PSOP TSOP TSOP +70 °C +85 °C
28F004BV √√√√√
28F400BV √√√√
28F400CV √√√√
28F004BE √√
28F400CE √√
E4-MBIT SmartVoltage BOOT BLOCK FAMILY
57
SEE NEW DESIGN RECOMMENDATIONS
6.0 ADDITIONAL INFORMATION
Related Intel Information(1,2)
Order
Number Document
290531
2-Mbit SmartVoltage Boot Block Flash Memory Family Datasheet
290539
8-Mbit SmartVoltage Boot Block Flash Memory Family Datasheet
290599
Smart 5 Boot Block Flash Memory Family 2, 4, 8 Mbit Datasheet
290580
Smart 3 Advanced Boot Block 4-Mbit, 8-Mbit, 16-Mbit Flash Memory Family Datasheet
292200
AP-642 Designing for Upgrade to Smart 3 Advanced Boot Block Flash Memory
292172
AP-617 Additional Flash Data Protection Using V
PP
, RP#, and WP#
292148
AP-604 Using Intel’s Boot Block Flash Memory Parameter Blocks to Replace EEPROM
292194
AB-65 Migrating SmartVoltage Boot Block Flash Designs to Smart 5 Flash
297595
28F400BV/CV/CE 28F004 BV/BE Specification Update
NOTES:
1. Please call the Intel Literature Center at (800) 548-4725 to request Intel documentation. International customers should
contact their local Intel or distribution sales office.
2. Visit Intel’s World Wide Web home page at http://www.Intel.com for technical documentation and tools.