Cat.No.T13E-14
Ceramic Trimmer
Capacitors
!Note T13E.pdf
Aug.10,2012
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
EU RoHS Compliant
s All the products in this catalog comply with EU RoHS.
s EU RoHS is "the European Directive 2011/65/EU on the Restriction of the Use
of Certain Hazardous Substances in Electrical and Electronic Equipment."
s For more details, please refer to our website 'Murata's Approach for EU RoHS'
(http://www.murata.com/info/rohs.html).
T13E.pdf
Aug.10,2012
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
T13E.pdf
Aug.10,2012
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
Part Numbering 2
Selection Guide of Ceramic Trimmer Capacitors 3
TZR1 Series 4
TZS2 Series 8
TZY2 Series 12
TZV2 Series 16
TZC3 Series 20
TZW4 Series 24
TZB4 Series 27
TZ03 Series 32
Packaging 37
Recommended Adjustment Tools 39
Qualified Standards 41
1
2
3
4
5
6
7
8
CONTENTS
Bluetoothr is a registered trademark or trademark of Bluetooth SIG, Inc.
in the United States and other countries.
1
2
3
4
5
6
7
8
T13E.pdf
Aug.10,2012
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
2
o Part Numbering
(Part Number)
qProduct ID
TZ Trimmer Capacitors
Product ID
rMaximum Capacitance
Expressed by three-digit alphanumerics. The unit is pico-farad
(pF). The first and second figures are significant digits, and the
third figure expresses the number of zeros that follow the two
numbers. If there is a decimal point, it is expressed by the capital
letter "R". In this case, all figures are significant digits.
Ceramic Trimmer Capacitors
tTerminal Shape
Code Terminal Shape
A
B
E
F
N
Top Adjustment:
Top Adjustment:
Rear Adjustment:
Top Adjustment:
Rear Adjustment:
TZR1, TZS2, TZY2, TZV2,
TZC3, TZW4, TZB4 (SMD Type)
TZB4 (SMD Type)
TZB4 (SMD Type)
TZ03 (Lead Type)
TZ03 (Lead Type)
uPackaging
Code
B00
R00
R01*
Bulk
Reel (Taping ø180mm)
Reel (Taping ø330mm)
Packaging
wSeries/Terminal
Code
03
B4
W4
C3
S2
Y2
V2
R1
6mm Size Lead Type
4mm Size SMD Type
4mm Size SMD Type
3mm Size SMD Type
2mm Size SMD Type (Height 1.0mm)
2mm Size SMD Type (Height 1.25mm)
2mm Size SMD Type (Height 1.45mm)
1mm Size SMD Type (Height 0.90mm)
Series/Terminal
eTemperature Characteristics
Code
Z
R
K
P
NP0ppm/°C
N750ppm/°C
N1000ppm/°C
N1200ppm/°C
Temperature Characteristics
Please refer to dimensions for terminal details.
* TZB4 only.
yIndividual Specifications
Code
001
110
169
A10
B10
TZR1, TZS2, TZY2, TZW4 Standard Type
TZV2, TZC3 Standard Type
TZ03 Standard Type
TZB4 No-cover Film Standard Type
TZB4 with Cover Film Standard Type
Individual Specifications
Please refer to ratings for tolerance of temperature characteristics.
t
A
y
001
q
TZ
u
R00
r
200
e
R
w
Y2
T13E.pdf
Aug.10,2012
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
3
Selection Guide of Ceramic Trimmer Capacitors
Mounting Method?
Surface Mount PCB Insertion
Height 0.90mm max.
Height 2.6mm max.
Height 1.7mm max. Height 3.2mm max. Height 5.3mm max.
TZC3
3.2(W) x 4.5(L)
TZB4_A
4.0(W) x 4.5(L)
TZB4_B
4.0(W) x 4.5(L)
TZB4_E
4.0(W) x 4.5(L)
TZW4
4.2(W) x 5.2(L)
TZ03_F
6.0(W) x 6.0(L)
TZ03_N
6.0(W) x 6.0(L)
TZB4_A
4.0(W) x 4.5(L)
(with cover film)
TZB4_B
4.0(W) x 4.5(L)
(with cover film)
TZB4_E
4.0(W) x 4.5(L)
(with cover film)
TZR1
1.5(W) x 1.7(L)
TZS2
2.2(W) x 2.7(L)
TZY2
2.5(W) x 3.2(L)
TZV2
2.3(W) x 3.2(L)
Height 1.00mm max. Height 3.2mm max.
Height 1.25mm max.
Height 1.45mm max.
Flow
Manual Insertion
Reflow
High Frequency Power
All Ceramic Trimmer Capacitor products comply with RoHS and ELV.
Ceramic Trimmer Capacitors
TZR1 Series
0.35
0.9 max.
1.5
0.45
1.7
0.2 (Depth;0.15)
(
Tolerance: ±0.1
)
in mm
Part Number C min. (max.)
(pF)
C max.
(pF) TC Q Rated Voltage Withstanding Voltage
TZR1Z010A001 0.55 1.0 +100/-0% NP0±300ppm/°C 200min. at 200MHz, Cmax. 25Vdc 55Vdc
TZR1Z1R5A001 0.7 1.5 +100/-0% NP0±300ppm/°C 200min. at 200MHz, Cmax. 25Vdc 55Vdc
TZR1Z040A001 1.5 4.0 +100/-0% NP0±500ppm/°C 300min. at 1MHz, Cmax. 25Vdc 55Vdc
TZR1R080A001 3.0 8.0 +100/-0% N750±500ppm/°C 300min. at 1MHz, Cmax. 25Vdc 55Vdc
Insulation Resistance: 10000M ohm Torque: 0.1 to 1.0mNm Operating Temperature Range: -25 to +85°C
Cover
Metal Rotor
Monolithic
Stator
c Construction
c Features
1. Ultra-small and thin with external dimensions
of 1.5(W)x1.7(L)x0.85(H)mm
(80% less in volume than the current product).
2. Unique construction with no plastic material
provides superior soldering heat resistance to
maintain excellent characteristic performance
after refl ow soldering.
3. Suitable for high frequency circuit due to high
self-resonant frequency (6.2GHz of TZR1Z010 at
1.0pF setting).
c Applications
1. Bluetoothr
2. Crystal oscillators
3. Crystal fi lters
4. Hand radios
5. Miniature tuner packs (FM Radio, TV)
6. Remote keyless entry systems
7. Pagers
T13E.pdf
Aug.10,2012
4
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
1
+8
+6
+4
+2
20
45
65 85
-2
-4
-6
-8
-10
-12
-25
-10 0
0
Z010 (NP0±300 ppm/°C)
Temp. (°C)
Cap. Change (%)
c Temperature Characteristics
TZR1Z010
+8
+6
+4
+2
20
45
65 85
-2
-4
-6
-8
-10
-12
-25
-10 0
0
Z1R5 (NP0±300 ppm/°C)
Temp. (°C)
Cap. Change (%)
TZR1Z1R5
+8
+6
+4
+2
20
0
–10
–25
45
65 85
–2
–4
–6
–8
–10
–12
0
Z040 (NP0±500 ppm/°C)
Cap.Change (%)
Temp.(°C)
TZR1Z040
+8
+6
+4
+2
20
0
–10
–25
45 65 85
–2
–4
–6
–8
–10
–12
0
R080 (N750±500 ppm/°C)
Cap.Change (%)
Temp.(°C)
TZR1R080
10000
1000
100
10
1
00246
Frequency (GHz)
0.55pF set
1.0pF set
Z010
Q
810
c Frequency Characteristics
TZR1Z010
10000
1000
100
10
1
00246
Frequency (GHz)
0.7pF set
1.5pF set
Z1R5
Q
810
TZR1Z1R5
1000 1000
100
10
Q
1
10
100
500 1000 1500 2000 2500
Frequency (MHz)
Capacitance (pF)
Z040
TZR1Z040
1000 1000
100
10
Q
1
10
100
500 1000 1500 2000
Frequency (MHz)
Capacitance (pF)
R080
TZR1R080
T13E.pdf
Aug.10,2012
5
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
1
2.2
1.2
0.5
Tolerance: ±0.1
in mm
c Land Pattern
Temperature (°C)
t3
t2
T3
T2
T5
T4
T1
time (s)
t1
Reflow Soldering Profile
qSoldering profile for Lead-free solder (96.5Sn/3Ag/0.5Cu)
Standard Profile
Pre-heating Heating
Peak
temperature
(T3)
Cycle
of reflow
Temp. (T1) Time (t1) Temp. (T2) Time (t2)
2 times245±3°C
150 to 180°C 60 to 120sec.
220°C
30 to 60sec.
Limit Profile
Standard Profile
Standard Profile
Pre-heating Heating Cycle
of reflow
Temp. (T1) Time (t1) Temp. (T2) Time (t2)
1 time
230 +5/-0°C
150°C
60 to 120sec.
183°C 30sec.
Limit Profile
Pre-heating Heating Cycle
of reflow
Temp. (T1) Time (t1) Temp. (T4) Time (t3)
2 times
260 +5/-0°C
150 to 180°C 60 to 120sec.
230°C
30 to 50sec.
Temperature (°C)
time (s)
Standard Profile
t1
T1 t2
T3
T2
wSoldering profile for Eutectic solder (63Sn/37Pb)
(Limit profile: refer to q)
Soldering Iron
Standard Profile
Temperature of soldering iron tip Soldering time Soldering iron power output
350±10°C
3sec. max. 30W max.
1 time
Cycle of soldering iron
Peak
temperature
(T5)
Peak
temperature
(T3)
c Temperature Profi le
c Notice (Storage and Operating Conditions)
6
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
1
1. Do not use the trimmer capacitor under atmosphere
of RTV silicone rubber (Room Temperature
Vulcanizing Silicone Rubber) except Acetone
liberating silicone sealant.
2. Before using trimmer capacitors, please store under
the conditions of -10 to +40°C and 30 to 85%RH.
3. Do not store in or near corrosive gasses.
4. Use within 6 months of delivery.
5. Do not store under direct sunlight.
6. Do not use the trimmer capacitor under the
conditions listed below.
(1) Corrosive gasses atmosphere
(ex. Chlorine gas, Hydrogen sulfi de gas,
Ammonia gas, Sulfuric acid gas, Nitric oxide gas,
etc.)
(2) In liquid (ex. water, oil, medical liquid,
organic solvent, etc.)
(3) Dusty / dirty atmosphere
(4) Direct sunlight
(5) Static voltage or electric/magnetic fi elds
(6) Direct sea breeze
(7) Other variations of the above
c Notice (Soldering and Mounting)
c Notice (Handling)
c Notice (Other)
Before using trimmer capacitors, please test after
assembly in your particular mass production system.
T13E.pdf
Aug.10,2012
7
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
1
1. Soldering
(1) TZR1 series can be soldered by refl ow soldering
method and soldering iron. Do not use fl ow
soldering method (dipping).
(2) Soldering conditions
Refer to the temperature profi le.
If the soldering conditions are not suitable, e.g.,
excessive time and/or excessive temperature, the
trimmer capacitor may deviate from the specifi ed
characteristics.
(3) The amount of solder is critical.
(4) The thickness of solder paste should be printed
from 100 micro m to 150 micro m and the dimension
of land pattern should be Murata's standard land
pattern used at refl ow soldering.
Insuffi cient amounts of solder can lead to
insuffi cient soldering strength on PCB.
Excessive amounts of solder may cause bridging
between the terminals or contact failure due to
fl ux wicking up.
(5) When using soldering iron, the diameter of the
string solder shall be less than 0.5mm. The
string solder shall be applied to the lower
part of the terminal only. Do not apply fl ux
except to the terminals. Excessive amounts of
solder and/or applying solder to the upper part
of the terminal may cause fi xed metal rotor or
contact failure due to fl ux invasion into
the movable part and/or the contact point. The
soldering iron should not come in contact with
the monolithic stator of the trimmer capacitor.
If such contact does occur, the trimmer
capacitor may be damaged.
(6) Our recommended chlorine content of solder is
as follows.
(a) Solder paste: 0.2wt% max.
(b) String solder: 0.5wt% max.
(7) Do not use water-soluble fl ux (for water
cleaning). To prevent the deterioration of
trimmer capacitor characteristics, apply fl ux
only to terminals.
2. Mounting
(1) Do not apply excessive force (preferably 5.0 N
[Ref: 500gf] max.), when the trimmer capacitor
is mounted on the PCB.
(2) Do not warp and/or bend PCB to protect trimmer
capacitor from breaking.
(3) Use a pick-up nozzle of a suitable dimension.
(1.1-1.2mm external diameter and 0.8-0.9mm bore
diameter.)
3. Cleaning
This product cannot be cleaned because of open
construction.
4. Other
Note the polarity of the trimmer capacitor to
minimize infl uence by stray capacitance.
(Refer to the dimensions concerning the polarity.)
1. Use suitable screwdrivers that fi t comfortably in
driver slot.
*Recommended screwdriver for manual adjustment
MURATA: KMDR160
2. When adjusting with a screwdriver, do not apply
excessive force (preferably 0.5 N [Ref: 50gf] max.)
to minimize capacitance drift. Excessive force applied
to the screwdriver slot may cause deformation of the
products.
3. Do not apply adhesive, lock paints, or any other
substances to the trimmer capacitor to secure the
rotor position. They may cause corrosion or
electrical contact problems.
Ceramic Trimmer Capacitors
TZS2 Series
in mm
Tolerance: ±0.1
2.7
1.0
1.0max. 2.2
0.6
0.4
0.20 Depth
Part Number C min. (max.)
(pF)
C max.
(pF) TC Q Rated Voltage Withstanding Voltage
TZS2Z060A001 3.0 6.0 +100/-0% NP0±300ppm/°C 500min. at 1MHz, Cmax. 25Vdc 55Vdc
TZS2Z100A001 3.5 10.0 +100/-0% NP0±300ppm/°C 500min. at 1MHz, Cmax. 25Vdc 55Vdc
TZS2R200A001 7.0 20.0 +100/-0% N750±500ppm/°C 500min. at 1MHz, Cmax. 25Vdc 55Vdc
Insulation Resistance: 10000M ohm Torque: 0.5 to 5.0mNm Operating Temperature Range: -25 to +85°C
Cover
Metal Rotor
Monolithic
Stator
c Construction
T13E.pdf
Aug.10,2012
8
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
2c Features
1. Ultra-small and thin type with external dimensions
of 2.2(W)x2.7(L)x0.95(H)mm
(30% less in volume than the current product).
2. Unique construction with no plastic material
provides superior soldering heat resistance to
maintain excellent characteristic performance
after refl ow soldering.
3. Pierced square hole allows for high resistance to
tuning force and in-process automatic adjustment.
c Applications
1. Crystal oscillators 8. Remote keyless entry systems
2. Crystal fi lters 9. PHS
3. Hand radios 10. Radar detectors
4. Cordless telephones 11. W-LAN
5. Cellular telephones 12. Compact radios
6. Tuner packs 13. Headphone stereos
7. Pagers
+8
+6
+4
+2
20
0
–10
–25
45
65 85
–2
–4
–6
–8
–10
–12
0
Z060 (NP0±300 ppm/°C)
Cap.Change (%)
Temp.(°C)
c Temperature Characteristics
TZS2Z060
+8
+6
+4
+2
20
0
–10
–25
45
65 85
–2
–4
–6
–8
–10
–12
0
Z100 (NP0±300 ppm/°C)
Cap.Change (%)
Temp.(°C)
TZS2Z100
+8
+6
+4
+2
20
0
–10
–25
45 65 85
–2
–4
–6
–8
–10
–12
0
R200 (N750±500 ppm/°C)
Cap.Change (%)
Temp.(°C)
TZS2R200
Z060
Q
1000
100
500 1000 1500 2000
10
1
1000
100
10
Frequency (MHz)
Capacitance (pF)
c Frequency Characteristics
TZS2Z060
Z100
Q
1000
100
200 600400 800 1000
10
1
1000
100
10
Frequency (MHz)
Capacitance (pF)
TZS2Z100
Continued on the following page.
T13E.pdf
Aug.10,2012
9
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
2
Continued from the preceding page.
R200
Q
1000
100
200 1000600 800400
10
1
1000
100
10
Frequency (MHz)
Capacitance (pF)
c Frequency Characteristics
TZS2R200
3.2
2.1
1.0
Tolerance: ±0.1
in mm
c Land Pattern
Temperature (°C)
t3
t2
T3
T2
T5
T4
T1
time (s)
t1
Reflow Soldering Profile
qSoldering profile for Lead-free solder (96.5Sn/3Ag/0.5Cu)
Standard Profile
Pre-heating Heating
Peak
temperature
(T3)
Cycle
of reflow
Temp. (T1) Time (t1) Temp. (T2) Time (t2)
2 times245±3°C
150 to 180°C 60 to 120sec.
220°C
30 to 60sec.
Limit Profile
Standard Profile
Standard Profile
Pre-heating Heating Cycle
of reflow
Temp. (T1) Time (t1) Temp. (T2) Time (t2)
1 time
230 +5/-0°C
150°C
60 to 120sec.
183°C 30sec.
Limit Profile
Pre-heating Heating Cycle
of reflow
Temp. (T1) Time (t1) Temp. (T4) Time (t3)
2 times
260 +5/-0°C
150 to 180°C 60 to 120sec.
230°C
30 to 50sec.
Temperature (°C)
time (s)
Standard Profile
t1
T1 t2
T3
T2
wSoldering profile for Eutectic solder (63Sn/37Pb)
(Limit profile: refer to q)
Soldering Iron
Standard Profile
Temperature of soldering iron tip Soldering time Soldering iron power output
350±10°C
3sec. max. 30W max.
1 time
Cycle of soldering iron
Peak
temperature
(T5)
Peak
temperature
(T3)
c Temperature Profi le
T13E.pdf
Aug.10,2012
10
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
2
c Notice (Storage and Operating Conditions)
c Notice (Soldering and Mounting)
c Notice (Handling)
c Notice (Other)
T13E.pdf
Aug.10,2012
11
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
2
1. Do not use the trimmer capacitor under atmosphere
of RTV silicone rubber (Room Temperature
Vulcanizing Silicone Rubber) except Acetone
liberating silicone sealant.
2. Before using trimmer capacitors, please store under
the conditions of -10 to +40°C and 30 to 85%RH.
3. Do not store in or near corrosive gasses.
4. Use within 6 months of delivery.
5. Do not store under direct sunlight.
6. Do not use the trimmer capacitor under the
conditions listed below.
(1) Corrosive gasses atmosphere
(ex. Chlorine gas, Hydrogen sulfi de gas,
Ammonia gas, Sulfuric acid gas, Nitric oxide gas,
etc.)
(2) In liquid (ex. water, oil, medical liquid,
organic solvent, etc.)
(3) Dusty / dirty atmosphere
(4) Direct sunlight
(5) Static voltage or electric/magnetic fi elds
(6) Direct sea breeze
(7) Other variations of the above
1. Use suitable screwdrivers that fi t comfortably in
driver slot.
(1) Recommended screwdriver for manual adjustment
MURATA: KMDR050
(2) Recommended screwdriver bit for automatic
adjustment
MURATA: KMBT050
2. When adjusting with a screwdriver, do not apply
excessive force (preferably 1.0 N [Ref: 100gf] max.)
to minimize capacitance drift. Excessive force applied
to the screwdriver slot may cause deformation of the
products.
3. Do not apply adhesive, lock paints, or any other
substances to the trimmer capacitor to secure the
rotor position. They may cause corrosion or
electrical contact problems.
Before using trimmer capacitors, please test after
assembly in your particular mass production system.
1. Soldering
(1) TZS2 series can be soldered by refl ow soldering
method and soldering iron. Do not use fl ow
soldering method (dipping).
(2) Soldering conditions
Refer to the temperature profi le.
If the soldering conditions are not suitable, e.g.,
excessive time and/or excessive temperature,
the trimmer capacitor may deviate from the
specifi ed characteristics.
(3) The amount of solder is critical.
(4) The thickness of solder paste should be printed
from 100 micro m to 150 micro m and the dimension
of land pattern should be Murata's standard land
pattern used at refl ow soldering.
Insuffi cient amounts of solder can lead to
insuffi cient soldering strength on PCB.
Excessive amounts of solder may cause bridging
between the terminals or contact failure due to
fl ux wicking up.
(5) When using soldering iron, the diameter of the
string solder shall be less than 0.5mm. The
string solder shall be applied to the lower part
of the terminal only. Do not apply fl ux except
to the terminals. Excessive amounts of solder
and/or applying solder to the upper part of the
terminal may cause fi xed metal rotor or contact
failure due to fl ux invasion into the movable
part and/or the contact point. The soldering
iron should not come in contact with the
monolithic stator of the trimmer capacitor.
If such contact does occur, the trimmer
capacitor may be damaged.
(6) Our recommended chlorine content of solder is
as follows.
(a) Solder paste: 0.2wt% max.
(b) String solder: 0.5wt% max.
(7) Do not use water-soluble fl ux (for water
cleaning). To prevent the deterioration of
trimmer capacitor characteristics, apply fl ux
only to terminals.
2. Mounting
(1) Do not apply excessive force (preferably 5.0 N
[Ref: 500gf] max.), when the trimmer capacitor
is mounted on the PCB.
(2) Do not warp and/or bend PCB to protect trimmer
capacitor from breakage.
(3) Use a pick-up nozzle of a suitable dimension.
(1.8mm external diameter and 1.3mm bore diameter.)
3. Cleaning
This product cannot be cleaned because of open
construction.
4. Other
Note the polarity of the trimmer capacitor to
minimize infl uence by stray capacitance.
(Refer to the dimensions concerning the polarity.)
Ceramic Trimmer Capacitors
TZY2 Series
3.2±0.2
2.5±0.2
1.25max. 0.95
1.0
0.45
0.5
1.4
(
Tolerance: ±0.1
)
in mm
Part Number C min. (max.)
(pF)
C max.
(pF) TC Q Rated Voltage Withstanding Voltage
TZY2Z010A001 0.5 1.0 +100/-0% NP0±300ppm/°C 200min. at 200MHz, Cmax. 25Vdc 55Vdc
TZY2Z2R5A001 0.65 2.5 +100/-0% NP0±300ppm/°C 200min. at 200MHz, Cmax. 25Vdc 55Vdc
TZY2Z030A001 1.5 3.0 +100/-0% NP0±300ppm/°C 300min. at 1MHz, Cmax. 25Vdc 55Vdc
TZY2Z060A001 2.5 6.0 +100/-0% NP0±300ppm/°C 500min. at 1MHz, Cmax. 25Vdc 55Vdc
TZY2Z100A001 3.0 10.0 +100/-0% NP0±300ppm/°C 500min. at 1MHz, Cmax. 25Vdc 55Vdc
TZY2R200A001 4.5 20.0 +100/-0% N750±500ppm/°C 500min. at 1MHz, Cmax. 25Vdc 55Vdc
TZY2R250A001 5.5 25.0 +100/-0% N750±500ppm/°C 300min. at 1MHz, Cmax. 25Vdc 55Vdc
TZY2K450A001 8.0 45.0 +100/-0% N1000±500ppm/°C 300min. at 1MHz, Cmax. 25Vdc 55Vdc
Insulation Resistance: 10000M ohm Torque: 0.5 to 5.0mNm Operating Temperature Range: -25 to +85°C
Cover
Metal Rotor
Monolithic
Stator
c Construction
T13E.pdf
Aug.10,2012
12
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
3
c Features
1. Small and thin size with external dimensions
of 2.5(W)x3.2(L)x1.25max.(H)mm.
2. New shape of cover can improve the fl ux invasion
compared with current products.
3. Improvement of the adhesion between rotor and
stator leads to superior stability.
4. Unique construction with no plastic material
provides superior soldering heat resistance to
maintain excellent characteristic performance
after refl ow soldering.
5. Suitable for high frequency circuit due to high
self-resonant frequency (4.8GHz of TZY2Z010 at
1.0pF setting).
c Applications
1. Crystal oscillators 9. Remote keyless entry systems
2. Crystal fi lters 10. W-LAN
3. Pagers 11. Radar detectors
4. Cordless telephones 12. Compact radios
5. PHS 13. DVD
6. Hand radios 14. Burglarproof devices
7. Cellular telephones 15. Headphone stereos
8. Watches
+8
+6
+4
+2
20 45
65 85
-2
-4
-6
-8
-10
-12
-25
-10 0
0
Z010 (NP0±300 ppm/°C)
Temp. (°C)
Cap. Change (%)
c Temperature Characteristics
TZY2Z010
+8
+6
+4
+2
20
0
–10
–25
45
65 85
–2
–4
–6
–8
–10
–12
0
Z100 (NP0±300 ppm/°C)
Cap.Change (%)
Temp.(°C)
TZY2Z100
+8
+6
+4
+2
20
0
–10
–25
45 65 85
–2
–4
–6
–8
–10
–12
0
R200 (N750±500 ppm/°C)
Cap.Change (%)
Temp.(°C)
TZY2R200
K450 (N1000±500ppm/°C)
Temp. (°C)
Cap. Change (%)
+12
+10
+8
+6
+4
+2
–2
0
–4
–6
–8
–10
–12
20 45
025
65 85
TZY2K450
1000
100
1
10
0246
Frequency (GHz)
0.5pF set
1.0pF set
Z010
8
Q
c Frequency Characteristics
TZY2Z010
Z100
Q
1000
100
200 600400 800 1000
10
1
1000
100
10
Frequency (MHz)
Capacitance (pF)
TZY2Z100
Continued on the following page.
T13E.pdf
Aug.10,2012
13
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
3
Continued from the preceding page.
R200
Q
1000
100
200 1000600 800400
10
1
1000
100
10
Frequency (MHz)
Capacitance (pF)
c Frequency Characteristics
TZY2R200
1000
100
10
1
1000
100
10
200
Q
400 600 800
Capacitance (pF)
Frequency (MHz)
K450
1000
100
10
1
1000
100
10
200
Q
400 600 800
Capacitance (pF)
Frequency (MHz)
K450
TZY2K450
Tolerance: ±0.1
in mm
4.0
2.4
1.2
c Land Pattern
Temperature (°C)
t3
t2
T3
T2
T5
T4
T1
time (s)
t1
Reflow Soldering Profile
qSoldering profile for Lead-free solder (96.5Sn/3Ag/0.5Cu)
Standard Profile
Pre-heating Heating
Peak
temperature
(T3)
Cycle
of reflow
Temp. (T1) Time (t1) Temp. (T2) Time (t2)
2 times245±3°C
150 to 180°C 60 to 120sec.
220°C
30 to 60sec.
Limit Profile
Standard Profile
Standard Profile
Pre-heating Heating Cycle
of reflow
Temp. (T1) Time (t1) Temp. (T2) Time (t2)
1 time
230 +5/-0°C
150°C
60 to 120sec.
183°C 30sec.
Limit Profile
Pre-heating Heating Cycle
of reflow
Temp. (T1) Time (t1) Temp. (T4) Time (t3)
2 times
260 +5/-0°C
150 to 180°C 60 to 120sec.
230°C
30 to 50sec.
Temperature (°C)
time (s)
Standard Profile
t1
T1 t2
T3
T2
wSoldering profile for Eutectic solder (63Sn/37Pb)
(Limit profile: refer to q)
Soldering Iron
Standard Profile
Temperature of soldering iron tip Soldering time Soldering iron power output
350±10°C
3sec. max. 30W max.
1 time
Cycle of soldering iron
Peak
temperature
(T5)
Peak
temperature
(T3)
c Temperature Profi le
T13E.pdf
Aug.10,2012
14
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
3
c Notice (Storage and Operating Conditions)
c Notice (Soldering and Mounting)
c Notice (Handling)
T13E.pdf
Aug.10,2012
15
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
3
c Notice (Other)
Before using trimmer capacitors, please test after
assembly in your particular mass production system.
1. Do not use the trimmer capacitor under atmosphere
of RTV silicone rubber (Room Temperature
Vulcanizing Silicone Rubber) except Acetone
liberating silicone sealant.
2. Before using trimmer capacitors, please store under
the conditions of -10 to +40°C and 30 to 85%RH.
3. Do not store in or near corrosive gasses.
4. Use within 6 months of delivery.
5. Do not store under direct sunlight.
6. Do not use the trimmer capacitor under the
conditions listed below.
(1) Corrosive gasses atmosphere
(ex. Chlorine gas, Hydrogen sulfi de gas,
Ammonia gas, Sulfuric acid gas, Nitric oxide gas,
etc.)
(2) In liquid (ex. water, oil, medical liquid,
organic solvent, etc.)
(3) Dusty / dirty atmosphere
(4) Direct sunlight
(5) Static voltage or electric/magnetic fi elds
(6) Direct sea breeze
(7) Other variations of the above
1. Use suitable screwdrivers that fi t comfortably in
driver slot.
(1) Recommended screwdriver for manual adjustment
ENGINEER INC.: DA-89
(Murata P/N is KMDR060)
(2) Recommended screwdriver bit for automatic
adjustment
MURATA: KMBT060
2. When adjusting with a screwdriver, do not apply
excessive force (preferably 1.0 N [Ref: 100gf] max.)
to minimize capacitance drift. Excessive force applied
to the screwdriver slot may cause deformation of the
products.
3. Do not apply adhesive, lock paints, or any other
substances to the trimmer capacitor to secure the
rotor position. They may cause corrosion or
electrical contact problems.
1. Soldering
(1) TZY2 series can be soldered by refl ow soldering
method and soldering iron. Do not use fl ow
soldering method (dipping).
(2) Soldering conditions
Refer to the temperature profi le.
If the soldering conditions are not suitable, e.g.,
excessive time and/or excessive temperature, the
trimmer capacitor may deviate from the specifi ed
characteristics.
(3) The amount of solder is critical.
(4) The thickness of solder paste should be printed
from 120 micro m to 170 micro m and the dimension
of land pattern should be Murata's standard land
pattern used at refl ow soldering.
Insuffi cient amounts of solder can lead to
insuffi cient soldering strength on PCB.
Excessive amounts of solder may cause bridging
between the terminals or contact failure due to
fl ux wicking up.
(5) When using soldering iron, the diameter of the
string solder shall be less than 0.5mm. The
string solder shall be applied to the lower
part of the terminal only. Do not apply fl ux
except to the terminals. Excessive amounts of
solder and/or applying solder to the upper part
of the terminal may cause fi xed metal rotor or
contact failure due to fl ux invasion into
the movable part and/or the contact point. The
soldering iron should not come in contact with
the monolithic stator of the trimmer capacitor.
If such contact does occur, the trimmer
capacitor may be damaged.
(6) Our recommended chlorine content of solder is
as follows.
(a) Solder paste: 0.2wt% max.
(b) String solder: 0.5wt% max.
(7) Do not use water-soluble fl ux (for water
cleaning). To prevent the deterioration of
trimmer capacitor characteristics, apply fl ux
only to terminals.
2. Mounting
(1) Do not apply excessive force (preferably 5.0 N
[Ref: 500gf] max.), when the trimmer capacitor
is mounted on the PCB.
(2) Do not warp and/or bend PCB to protect trimmer
capacitor from breakage.
(3) Use a pick-up nozzle of a suitable dimension.
(1.8mm external diameter and 1.3mm bore diameter.)
3. Cleaning
This product cannot be cleaned because of open
construction.
4. Other
Note the polarity of the trimmer capacitor to
minimize infl uence by stray capacitance.
(Refer to the dimensions concerning the polarity.)
Ceramic Trimmer Capacitors
TZV2 Series
3.2±0.2
0.5 Depth 0.2
2.3±0.2
1.45max.
1.4
Marking(6pF)
Marking(10pF)
Tolerance: ±0.1
in mm
1.0
Part Number C min. (max.)
(pF)
C max.
(pF) TC Q Rated Voltage Withstanding Voltage
TZV2Z2R5A110 0.65 2.5 +100/-0% NP0±300ppm/°C 200min. at 200MHz, Cmax. 25Vdc 55Vdc
TZV2Z030A110 1.5 3.0 +100/-0% NP0±300ppm/°C 300min. at 1MHz, Cmax. 25Vdc 55Vdc
TZV2Z060A110 2.5 6.0 +100/-0% NP0±300ppm/°C 500min. at 1MHz, Cmax. 25Vdc 55Vdc
TZV2Z100A110 3.0 10.0 +100/-0% NP0±300ppm/°C 500min. at 1MHz, Cmax. 25Vdc 55Vdc
TZV2R200A110 4.5 20.0 +100/-0% N750±500ppm/°C 500min. at 1MHz, Cmax. 25Vdc 55Vdc
Insulation Resistance: 10000M ohm Torque: 1.0 to 9.8mNm Operating Temperature Range: -25 to +85°C
Cover
Spring Washer
Metal Rotor
Monolithic Stator
c Construction
T13E.pdf
Aug.10,2012
16
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
4
c Features
1. Small size with external dimensions of
2.3(W)x3.2(L)x1.45max.(H)mm.
2. Unique construction with no plastic material
provides superior soldering heat resistance to
maintain excellent characteristic performance after
refl ow soldering.
3. Designed for automatic placement in surface mount
applications.
4. Funnel shaped metal case enables in-process
automatic adjustment.
c Applications
1. Crystal oscillator 9. PHS
2. Crystal fi lters 10. Radar detectors
3. Hand radios 11. W-LAN
4. Cordless telephones 12. Compact radios
5. Cellular telephones 13. Headphone stereos
6. Tuner packs 14. DVD
7. Pagers 15. Burglarproof devices
8. Remote keyless entry systems
+8
+6
+4
+2
20
0
–10
–25
45
65 85
–2
–4
–6
–8
–10
–12
0
Z2R5 (NP0±300 ppm/°C)
Temp.(°C)
Cap.Change (%)
c Temperature Characteristics
TZV2Z2R5
+8
+6
+4
+2
20
0
–10
–25
45
65 85
–2
–4
–6
–8
–10
–12
0
Z060 (NP0±300 ppm/°C)
Cap.Change (%)
Temp.(°C)
TZV2Z060
+8
+6
+4
+2
20
0
–10
–25
45
65 85
–2
–4
–6
–8
–10
–12
0
Z100 (NP0±300 ppm/°C)
Cap.Change (%)
Temp.(°C)
TZV2Z100
+8
+6
+4
+2
20
0
–10
–25
45 65 85
–2
–4
–6
–8
–10
–12
0
R200 (N750±500 ppm/°C)
Cap.Change (%)
Temp.(°C)
TZV2R200
Z2R5
1000
100
Q
500 1000 1500 2000 2500 3000
10
1
1000
100
10
Frequency (MHz)
Capacitance (pF)
c Frequency Characteristics
TZV2Z2R5
Z060
Q
1000
100
500 1000 1500 2000
10
1
1000
100
10
Frequency (MHz)
Capacitance (pF)
TZV2Z060
Continued on the following page.
T13E.pdf
Aug.10,2012
17
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
4
Continued from the preceding page.
Z100
Q
1000
100
200 600400 800 1000
10
1
1000
100
10
Frequency (MHz)
Capacitance (pF)
c Frequency Characteristics
TZV2Z100
R200
Q
1000
100
200 1000600 800400
10
1
1000
100
10
Frequency (MHz)
Capacitance (pF)
TZV2R200
Tolerance: ±0.1
in mm
4.0
2.4
1.2
c Land Pattern
Temperature (°C)
t3
t2
T3
T2
T5
T4
T1
time (s)
t1
Reflow Soldering Profile
qSoldering profile for Lead-free solder (96.5Sn/3Ag/0.5Cu)
Standard Profile
Pre-heating Heating
Peak
temperature
(T3)
Cycle
of reflow
Temp. (T1) Time (t1) Temp. (T2) Time (t2)
2 times245±3°C
150 to 180°C 60 to 120sec.
220°C
30 to 60sec.
Limit Profile
Standard Profile
Standard Profile
Pre-heating Heating Cycle
of reflow
Temp. (T1) Time (t1) Temp. (T2) Time (t2)
1 time
230 +5/-0°C
150°C
60 to 120sec.
183°C 30sec.
Limit Profile
Pre-heating Heating Cycle
of reflow
Temp. (T1) Time (t1) Temp. (T4) Time (t3)
2 times
260 +5/-0°C
150 to 180°C 60 to 120sec.
230°C
30 to 50sec.
Temperature (°C)
time (s)
Standard Profile
t1
T1 t2
T3
T2
wSoldering profile for Eutectic solder (63Sn/37Pb)
(Limit profile: refer to q)
Soldering Iron
Standard Profile
Temperature of soldering iron tip Soldering time Soldering iron power output
350±10°C
3sec. max. 30W max.
1 time
Cycle of soldering iron
Peak
temperature
(T5)
Peak
temperature
(T3)
c Temperature Profi le
T13E.pdf
Aug.10,2012
18
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
4
c Notice (Storage and Operating Conditions)
c Notice (Soldering and Mounting)
c Notice (Handling)
T13E.pdf
Aug.10,2012
19
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
4
c Notice (Other)
Before using trimmer capacitors, please test after
assembly in your particular mass production system.
1. Use suitable screwdrivers that fi t comfortably in
driver slot.
(1) Recommended screwdriver for manual adjustment
VESSEL: No.9000 -0.9x30
(Murata P/N : KMDR020)
(2) Recommended screwdriver bit for automatic
adjustment
MURATA: KMBT020
2. When adjusting with a screwdriver, do not apply
excessive force (preferably 1.0 N [Ref: 100gf] max.)
to minimize capacitance drift. Excessive force applied
to the screwdriver slot may cause deformation of the
products.
3. Do not apply adhesive, lock paints, or any other
substances to the trimmer capacitor to secure the
rotor position. They may cause corrosion or
electrical contact problems.
1. Do not use the trimmer capacitor under atmosphere
of RTV silicone rubber (Room Temperature
Vulcanizing Silicone Rubber) except Acetone
liberating silicone sealant.
2. Before using trimmer capacitors, please store under
the conditions of -10 to +40°C and 30 to 85%RH.
3. Do not store in or near corrosive gasses.
4. Use within 6 months of delivery.
5. Do not store under direct sunlight.
6. Do not use the trimmer capacitor under the
conditions listed below.
(1) Corrosive gasses atmosphere
(ex. Chlorine gas, Hydrogen sulfi de gas,
Ammonia gas, Sulfuric acid gas, Nitric oxide gas,
etc.)
(2) In liquid (ex. water, oil, medical liquid,
organic solvent, etc.)
(3) Dusty / dirty atmosphere
(4) Direct sunlight
(5) Static voltage or electric/magnetic fi elds
(6) Direct sea breeze
(7) Other variations of the above
1. Soldering
(1) TZV2 series can be soldered by refl ow soldering
method and soldering iron. Do not use fl ow
soldering method (dipping).
(2) Soldering conditions
Refer to the temperature profi le.
If the soldering conditions are not suitable, e.g.,
excessive time and/or excessive temperature, the
trimmer capacitor may deviate from the specifi ed
characteristics.
(3) The amount of solder is critical.
(4) The thickness of solder paste should be printed
from 120 micro m to 170 micro m and the dimension
of land pattern should be Murata's standard land
pattern used at refl ow soldering.
Insuffi cient amounts of solder can lead to
insuffi cient soldering strength on PCB.
Excessive amounts of solder may cause
bridging between the terminals or contact
failure due to fl ux wicking up.
(5) When using soldering iron, the diameter of the
string solder shall be less than 0.5mm. The
string solder shall be applied to the lower
part of the terminal only. Do not apply fl ux
except to the terminals. Excessive amounts of
solder and/or applying solder to the upper part
of the terminal may cause fi xed metal rotor or
contact failure due to fl ux invasion into
the movable part and/or the contact point. The
soldering iron should not come in contact with
the monolithic stator of the trimmer capacitor.
If such contact does occur, the trimmer
capacitor may be damaged.
(6) Our recommended chlorine content of solder is
as follows.
(a) Solder paste: 0.2wt% max.
(b) String solder: 0.5wt% max.
(7) Do not use water-soluble fl ux (for water
cleaning). To prevent the deterioration of
trimmer capacitor characteristics, apply fl ux
only to terminals.
2. Mounting
(1) Do not apply excessive force (preferably 5.0 N
[Ref: 500gf] max.), when the trimmer capacitor
is mounted on the PCB.
(2) Do not warp and/or bend PCB to protect trimmer
capacitor from breakage.
(3) Use a pick-up nozzle of a suitable dimension.
(1.8mm external diameter and 1.3mm bore diameter.)
3. Cleaning
This product cannot be cleaned because of open
construction.
4. Other
Note the polarity of the trimmer capacitor to
minimize infl uence by stray capacitance.
(Refer to the dimensions concerning the polarity.)
Ceramic Trimmer Capacitors
TZC3 Series
0.5
2.5 dia.
4.5
0.75
3.2
0.8
0.35
1.6
4.5
0.6 0.6
0.8
Tolerance: ±0.1
in mm
Part Number C min. (max.)
(pF)
C max.
(pF) TC Q Rated Voltage Withstanding Voltage Stator/Case Color
TZC3Z030A110 1.4 3.0 +50/-0% NP0±300ppm/°C 300min. at 1MHz, Cmax. 100Vdc 220Vdc Brown
TZC3Z060A110 2.0 6.0 +50/-0% NP0±300ppm/°C 500min. at 1MHz, Cmax. 100Vdc 220Vdc Blue
TZC3R100A110 3.0 10.0 +50/-0% N750±300ppm/°C 500min. at 1MHz, Cmax. 100Vdc 220Vdc White
TZC3P200A110 5.0 20.0 +50/-0% N1200±500ppm/°C 300min. at 1MHz, Cmax. 100Vdc 220Vdc Red
TZC3P300A110 6.5 30.0 +50/-0% N1200±500ppm/°C 300min. at 1MHz, Cmax. 100Vdc 220Vdc Green
Insulation Resistance: 10000M ohm Torque: 1.5 to 9.8mNm Operating Temperature Range: -25 to +85°C
Center axis
Rotor spring terminal
Ceramic plate
Stator
(One molded injection
with stator terminal)
Stator terminal
c Construction
c Features
1. Small size with external dimension of
3.2(W)x4.5(L)x1.6(H)mm.
2. Color coded stator permits easy identifi cation of
capacitance and reduces mounting errors.
3. Can be adjusted with conventional adjustment tools
having a thickness of 0.5mm.
4. Designed for automatic placement in surface mount
applications.
5. Heat resistant resin withstands refl ow soldering
temperatures.
c Applications
1. Compact radios
2. Headphones
3. Pagers
4. Portable radio equipment
5. Hybrid ICs
6. Cellular telephones
7. Cordless telephones
8. Remote keyless entry systems
T13E.pdf
Aug.10,2012
20
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
5
+8
+6
+4
+2
20
0
–10
–25 45 65
85
–2
–4
–6
–8
–10
–12
Temp.(°C)
0
Z030 (NP0±300 ppm/°C)
Cap.Change (%)
c Temperature Characteristics
TZC3Z030
+8
+6
+4
+2
20
0
–10
–25 45 65 85
–2
–4
–6
–8
–10
–12
Temp.(°C)
0
Z060 (NP0±300 ppm/°C)
Cap.Change (%)
TZC3Z060
+8
+6
+4
+2
0
–10
–25
45 65 85
–2
20
–4
–6
–8
–10
–12
Temp.(°C)
0
R100 (N750±300 ppm/°C)
Cap.Change (%)
TZC3R100
+8
+6
+4
+2
0
0
–10
–25
45 65 85
–2
–4
–6
–8
–10
–12
Temp.(°C)
20
P200 (N1200±500ppm/°C)
Cap.Change (%)
TZC3P200
Z030
1000
100
Q
100 500 1000 1500
Frequency (MHz)
2000
10
1
1000
100
10
Capacitance (pF)
c Frequency Characteristics
TZC3Z030
Z060
Q
1000
100
100 500 2000
15001000
Frequency (MHz)
10
1
1000
100
10
Capacitance (pF)
TZC3Z060
Continued on the following page.
T13E.pdf
Aug.10,2012
21
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
5
Continued from the preceding page.
R100
Q
1000
100
200 600400 800 1000
Frequency (MHz)
10
1
1000
100
10
Capacitance (pF)
c Frequency Characteristics
TZC3R100
P200
Q
1000
100
200 1000600 800400
Frequency (MHz)
10
1
1000
100
10
Capacitance (pF)
TZC3P200
5.0 +0
–0.5
3.3±0.1
1.0±0.1
Tolerance: ±0.1
in mm
c Land Pattern
Temperature (°C)
t3
t2
T3
T2
T5
T4
T1
time (s)
t1
Reflow Soldering Profile
qSoldering profile for Lead-free solder (96.5Sn/3Ag/0.5Cu)
Standard Profile
Pre-heating Heating
Peak
temperature
(T3)
Cycle
of reflow
Temp. (T1) Time (t1) Temp. (T2) Time (t2)
2 times245±3°C
150 to 180°C 60 to 120sec.
220°C
30 to 60sec.
Limit Profile
Standard Profile
Standard Profile
Pre-heating Heating Cycle
of reflow
Temp. (T1) Time (t1) Temp. (T2) Time (t2)
1 time
230 +5/-0°C
150°C
60 to 120sec.
183°C 30sec.
Limit Profile
Pre-heating Heating Cycle
of reflow
Temp. (T1) Time (t1) Temp. (T4) Time (t3)
2 times
260 +5/-0°C
150 to 180°C 60 to 120sec.
230°C
30 to 50sec.
Temperature (°C)
time (s)
Standard Profile
t1
T1 t2
T3
T2
wSoldering profile for Eutectic solder (63Sn/37Pb)
(Limit profile: refer to q)
Soldering Iron
Standard Profile
Temperature of soldering iron tip Soldering time Soldering iron power output
350±10°C
3sec. max. 30W max.
1 time
Cycle of soldering iron
Peak
temperature
(T5)
Peak
temperature
(T3)
c Temperature Profi le
T13E.pdf
Aug.10,2012
22
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
5
c Notice (Storage and Operating Conditions)
c Notice (Soldering and Mounting)
c Notice (Handling)
T13E.pdf
Aug.10,2012
23
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
5
1. Do not use the trimmer capacitor under atmosphere
of RTV silicone rubber (Room Temperature
Vulcanizing Silicone Rubber) except Acetone
liberating silicone sealant.
2. Before using trimmer capacitors, please store under
the conditions of -10 to +40°C and 30 to 85%RH.
3. Do not store in or near corrosive gasses.
4. Use within 6 months of delivery.
5. Do not store under direct sunlight.
6. Do not use the trimmer capacitor under the
conditions listed below.
(1) Corrosive gasses atmosphere
(ex. Chlorine gas, Hydrogen sulfi de gas,
Ammonia gas, Sulfuric acid gas, Nitric oxide gas, etc.)
(2) In liquid (ex. water, oil, medical liquid,
organic solvent, etc.)
(3) Dusty / dirty atmosphere
(4) Direct sunlight
(5) Static voltage or electric/magnetic fi elds
(6) Direct sea breeze
(7) Other variations of the above
1. Soldering
(1) TZC3 series can be soldered by refl ow soldering
method and soldering iron. Do not use fl ow
soldering method (dipping).
(2) Soldering conditions
Refer to the temperature profi le.
If the soldering conditions are not suitable, e.g.,
excessive time and/or excessive temperature, the
trimmer capacitor may deviate from the specifi ed
characteristics.
(3) The amount of solder is critical.
(4) The thickness of solder paste should be printed
from 150 micro m to 200 micro m and the dimension
of land pattern should be Murata's standard land
pattern used at refl ow soldering.
Insuffi cient amounts of solder can lead to
insuffi cient soldering strength on PCB.
Excessive amounts of solder may cause bridging
between the terminals or contact failure due to
fl ux wicking up.
(5) When using soldering iron, the diameter of the
string solder shall be less than 0.5mm. The
string solder shall be applied to the lower
part of the terminal only. Do not apply fl ux
except to the terminals. Excessive amounts of
solder and/or applying solder to the upper part
of the terminal may cause fi xed metal rotor or
contact failure due to fl ux invasion into the
movable part and/or the contact point. The
soldering iron should not come in contact with
the stator of the trimmer capacitor. If such contact does
occur, the trimmer capacitor may be damaged.
(6) Our recommended chlorine content of solder is
as follows.
(a) Solder paste: 0.2wt% max.
(b) String solder: 0.5wt% max.
(7) Do not use water-soluble fl ux (for water cleaning).
To prevent the deterioration of trimmer capacitor
characteristics, apply fl ux only to terminals.
(8) When soldering the TZC3 series, the solder
should not fl ow into the staking part of the
substrate. If such fl ow does occur, driver slot
rotation will be damaged.
2. Mounting
(1) Do not apply excessive force (preferably 5.0 N
[Ref: 500gf] max.), when the trimmer capacitor
is mounted on the PCB.
(2) Do not warp and/or bend PCB to protect trimmer
capacitor from breakage.
(3) Use a pick-up nozzle of a suitable dimension.
(2.5mm external diameter and 1.5mm bore diameter.)
3. Cleaning
This product cannot be cleaned because of open
construction.
4. Other
Note the polarity of the trimmer capacitor to
minimize infl uence by stray capacitance.
(Refer to the dimensions concerning the polarity.)
1. Use suitable screwdrivers that fi t comfortably in driver slot.
(1) Recommended screwdriver for manual adjustment
Standard type --> MURATA: KMDR010
Cross slot type --> VESSEL: NO.9000+1.7×30
(Murata P/N is KMDR080)
(2) Recommended screwdriver bit for automatic adjustment
Standard type --> MURATA: KMBT010
Cross slot type --> VESSEL: No.CA-11
(Murata P/N is KMBT080)
2. When adjusting with a screwdriver, do not apply
excessive force (preferably 1.0 N [Ref: 100gf] max.)
to minimize capacitance drift. Excessive force applied
to the screwdriver slot may cause deformation of the
products.
3. Do not apply adhesive, lock paints, or any other
substances to the trimmer capacitor to secure the
rotor position. They may cause corrosion or
electrical contact problems.
c Notice (Other)
Before using trimmer capacitors, please test after
assembly in your particular mass production system.
Ceramic Trimmer Capacitors
TZW4 Series
5.2±0.2
4.2±0.2
2.8±0.2 2.6 max.
(
Tolerance: ±0.1
)
in mm
0.6
+0.1
-0.2
0.3
1.6
0.4 Depth
3.0
2.2
Part Number C min. (max.)
(pF)
C max.
(pF) TC Q Rated Voltage Withstanding Voltage
TZW4Z010A001 0.4 1.0 +50/-0% NP0±150ppm/°C 200min. at 500MHz, Cmax. 250Vdc 550Vdc
TZW4Z1R5A001 0.4 1.5 +100/-0% NP0±150ppm/°C 200min. at 500MHz, Cmax. 250Vdc 550Vdc
Insulation Resistance: 10000M ohm Torque: 1.5 to 10.0mNm Operating Temperature Range: -55 to +125°C
Cover
Metal Rotor
Monolithic
Stator
c Construction
c Features
1. To meet high power application due to withstanding
voltage 550Vdc.
2. Extremely high self-resonant frequency.
(More than 3GHz at rated Cmax.)
3. Typical application: Impedance matching for Cellular
Base Station.
4. High Q value in more than VHF, UHF and Microwave
bands.
(More than 200 in 500MHz, C max.)
5. Available for pick and place machine. Possible
thinner design due to 2.6mm low profi le.
6. Non-electrical contact construction
(rotor as middle electrode) provides high reliability.
7. Compact size: 4.2(W)x5.2(L)x2.6max.(H)mm.
c Applications
1. Transmitting power amplifi er for Cellular base station
2. Transmitting amplifi er for PHS base station
3. High frequency electric circuit
4. High power radio transmission
5. Transponder amplifi er for cable TV
T13E.pdf
Aug.10,2012
24
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
6
+8
+6
+4
+2
20
0–10–25
–55 45 65 85 105 125
–2
–4
–6
–8
–10
–12
0
Z1R5 (NP0±150 ppm/°C)
Temp. (°C)
Cap.Change (%)
c Temperature Characteristics
TZW4Z1R5
Z1R5
1000
100
Q
500 1000 1500 2000 2500 3000
10
1
Frequency (MHz)
1.5pF set
c Frequency Characteristics
TZW4Z1R5
Tolerance: ±0.1
in mm
4.4
7.0
2.5
c Land Pattern
Temperature (°C)
t3
t2
T3
T2
T5
T4
T1
time (s)
t1
Reflow Soldering Profile
qSoldering profile for Lead-free solder (96.5Sn/3Ag/0.5Cu)
Standard Profile
Pre-heating Heating
Peak
temperature
(T3)
Cycle
of reflow
Temp. (T1) Time (t1) Temp. (T2) Time (t2)
2 times245±3°C
150 to 180°C 60 to 120sec.
220°C
30 to 60sec.
Limit Profile
Standard Profile
Standard Profile
Pre-heating Heating Cycle
of reflow
Temp. (T1) Time (t1) Temp. (T2) Time (t2)
1 time
230 +5/-0°C
150°C
60 to 120sec.
183°C 30sec.
Limit Profile
Pre-heating Heating Cycle
of reflow
Temp. (T1) Time (t1) Temp. (T4) Time (t3)
2 times
260 +5/-0°C
150 to 180°C 60 to 120sec.
230°C
30 to 50sec.
Temperature (°C)
time (s)
Standard Profile
t1
T1 t2
T3
T2
wSoldering profile for Eutectic solder (63Sn/37Pb)
(Limit profile: refer to q)
Soldering Iron
Standard Profile
Temperature of soldering iron tip Soldering time Soldering iron power output
350±10°C
3sec. max. 30W max.
1 time
Cycle of soldering iron
Peak
temperature
(T5)
Peak
temperature
(T3)
c Temperature Profi le
T13E.pdf
Aug.10,2012
25
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
6
c Notice (Storage and Operating Conditions)
c Notice (Soldering and Mounting)
1. Soldering
(1) TZW4 series can be soldered by refl ow soldering
method and soldering iron. Do not use fl ow
soldering method (dipping).
(2) Soldering conditions
Refer to the temperature profi le.
If the soldering conditions are not suitable, e.g.,
excessive time and/or excessive temperature, the
trimmer capacitor may deviate from the specifi ed
characteristics.
(3) The amount of solder is critical.
(4) The thickness of solder paste should be printed
from 150 micro m to 200 micro m and the dimension
of land pattern should be Murata's standard land
pattern used at refl ow soldering.
Insuffi cient amounts of solder can lead to
insuffi cient soldering strength on PCB.
Excessive amounts of solder may cause bridging
between the terminals or contact failure due to
fl ux wicking up.
(5) When using soldering iron, the diameter of the
string solder shall be less than 0.5mm. The
string solder shall be applied to the lower
part of the terminal only. Do not apply fl ux
except to the terminals. Excessive amounts of
solder and/or applying solder to the upper part
of the terminal may cause fi xed metal rotor or
the contact failure due to fl ux invasion into
the movable part and/or the contact point. The
soldering iron should not come in contact with
the monolithic stator of the trimmer capacitor.
If such contact does occur, the trimmer
capacitor may be damaged.
(6) Our recommended chlorine content of solder is
as follows.
(a) Solder paste: 0.2wt% max.
(b) String solder: 0.5wt% max.
(7) Do not use water-soluble fl ux (for water
cleaning). To prevent the deterioration of
trimmer capacitor characteristics, apply fl ux
only to terminals.
2. Mounting
(1) Do not apply excessive force (preferably 5.0 N
[Ref: 500gf] max.), when the trimmer capacitor
is mounted on the PCB.
(2) Do not warp and/or bend PCB to protect trimmer
capacitor from breaking.
(3) Use a pick-up nozzle of a suitable dimension.
(1.8mm external diameter and 1.1mm bore
diameter.)
3. Cleaning
This product cannot be cleaned because of open
construction.
c Notice (Handling)
c Notice (Other)
Before using trimmer capacitors, please test after
assembly in your particular mass production system.
T13E.pdf
Aug.10,2012
26
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
6
6. Do not use the trimmer capacitor under the
conditions listed below.
(1) Corrosive gasses atmosphere
(Ex. Chlorine gas, Hydrogen sulfi de gas,
Ammonia gas, Sulfuric acid gas, Nitric oxide gas,
etc.)
(2) In liquid (Ex. water, oil, medical liquid,
organic solvent, etc.)
(3) Dusty/dirty atmosphere
(4) Direct sunlight
(5) Static voltage or electric/magnetic fi elds
(6) Direct sea breeze
(7) Other variations of the above
1. Do not use the trimmer capacitor under atmosphere
of RTV silicone rubber (Room Temperature
Vulcanizing Silicone Rubber) except Acetone
liberating silicone sealant.
2. Before using trimmer capacitors, please store under
the conditions of -10 to +40°C and 30 to 85%RH.
3. Do not store in or near corrosive gasses.
4. Use within 6 months of delivery.
5. Do not store under direct sunlight.
1. Use suitable screwdrivers that fi t comfortably in
driver slot.
-Recommended screwdriver for manual adjustment
VESSEL : No.9000 -1.3x30
(Murata P/N is KMDR130)
2. When adjusting with a screwdriver, do not apply
excessive force (preferably 1.0 N [Ref: 100gf] max.)
to minimize capacitance drift. Excessive force applied
to the screwdriver slot may cause deformation of the
products.
3. Do not apply adhesive, lock paints, or any other
substances to the trimmer capacitor to secure the
rotor position. They may cause corrosion or
electrical contact problems.
Ceramic Trimmer Capacitors
TZB4 Series
0.6±0.1 Depth 0.5 1.4±0.1 dia.
2.7±0.3
2.4±0.1
4.0±0.2
4.5±0.2
5.0
1.2±0.1
3.0±0.2
Tolerance: ±0.5
in mm
A Type
0.6±0.1 Depth 0.5 1.4±0.1 dia.
2.4±0.1
4.0±0.2
4.5±0.2
7.0
1.2±0.1
3.0±0.2
Tolerance: ±0.5
in mm
B Type
0.6±0.1 Depth 0.5
4.8
2.4±0.1
4.0±0.2
4.5±0.2
4.5
4.0±0.2
3.0±0.2
Tolerance: ±0.5
in mm
7.0
0.8±0.1
E Type
Part Number C min. (max.)
(pF)
C max.
(pF) TC Q Rated Voltage Withstanding Voltage Stator/Case Color
TZB4Z030pp10
1.4 3.0 +50/-0% NP0±200ppm/°C 300min. at 1MHz, Cmax 100Vdc 220Vdc Brown
TZB4Z060pp10
2.0 6.0 +50/-0% NP0±200ppm/°C 500min. at 1MHz, Cmax. 100Vdc 220Vdc Blue
TZB4Z100pp10
3.0 10.0 +50/-0% NP0±300ppm/°C 500min. at 1MHz, Cmax. 100Vdc 220Vdc White
TZB4R200pp10
4.5 20.0 +50/-0% N750±400ppm/°C 500min. at 1MHz, Cmax 100Vdc 220Vdc Red
TZB4P300pp10
6.5 30.0 +50/-0% N1200±500ppm/°C 300min. at 1MHz, Cmax 100Vdc 220Vdc Green
TZB4P400pp10
8.5 40.0 +50/-0% N1200±500ppm/°C 300min. at 1MHz, Cmax 100Vdc 220Vdc Yellow
TZB4Z250pp10
4.0 25.0 +100/-0% NP0±300ppm/°C 300min. at 1MHz, Cmax. 50Vdc 110Vdc Black+Marking
TZB4R500pp10
7.0 50.0 +100/-0% N750±300ppm/°C 300min. at 1MHz, Cmax 50Vdc 110Vdc Black+Marking
c Features
1. Miniature rectangular shape:
4.0(W)x4.5(L)x3.0(H)mm.
2. Color coded case facilitates identifi cation of
capacitance range.
3. Designed for automatic placement in surface mount
applications.
4. Designed to withstand fl ux baths and solder baths
(with cover fi lm type).
5. Can be temporarily attached to PCB with adhesives
(Terminal style A and B).
6. Can be refl ow and fl ow (with cover fi lm type)
soldering method.
7. Stable characteristics over a wide frequency range.
(Resonant frequency: 1000MHz min. / 6pF)
c Applications
1. Car audio systems
2. Cordless telephones
3. Hybrid ICs
4. Pagers
5. Remote keyless entry systems
6. Tuner packs
7. Surveillance cameras
8. DVD
9. Burglarproof devices
T13E.pdf
Aug.10,2012
27
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
7
Insulation Resistance: 10000M ohm Torque: 1.5 to 9.8mNm Operating Temperature Range: -25 to +85°C
First blank: Terminal Type Second blank: Cover fi lm codes (A: not provided, B: provided)
ex. TZB4Z100A B10: Terminal Type is A, and Cover fi lm is provided.
Plastic Case
Rotor Spring
Metal Rotor
Ceramic Plate
Stator Terminal
Cover Film (Cover film type)
Rotor Terminal
–
+
c Construction
1.6±0.1
7.0
+0
- 0.5
2.4±0.2
(in mm)
c Land Pattern/Mounting Holes
A Type
(in mm)
4.0±0.2
1.6±0.1
8.0
+0
- 0.5
B Type
8.0
+0
- 0.5
4.2±0.2
1.2±0.1
3.2±0.2 dia.
(in mm)
E Type
+8
+10
+6
+4
+2
+20
0
–25
+55 +85
–2
–4
–6
–8
–10
0
Z060 (NP0±200ppm/°C)
Temp. (°C)
Cap.Change (%)
c Temperature Characteristics
TZB4Z060
+8
+10
+6
+4
+2
+20
0
–25
+55 +85
–2
–4
–6
–8
–10
0
Z100 (NP0±300ppm/°C)
Cap.Change (%)
Temp. (°C)
TZB4Z100
Continued on the following page.
T13E.pdf
Aug.10,2012
28
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
7
Continued from the preceding page.
+8
+10
+6
+4
+2
+20
0
–25
+55 +85
–2
–4
–6
–8
–10
0
R200 (N750±400ppm/°C)
Cap.Change (%)
Temp. (°C)
c Temperature Characteristics
TZB4R200
+8
+10
+6
+4
+2
+20
0
–25
+55 +85
–2
–4
–6
–8
–10
0
R500 (N750±300ppm/°C)
Cap.Change (%)
Temp.(°C)
TZB4R500
Z060
1000
100
Q
10
1000
100
10
800700600500400300200100 900 1000
Frequency (MHz)
1
Capacitance (pF)
c Frequency Characteristics
TZB4Z060
Z100
Q
1000
100
800700600500400300200100 900 1000
Frequency (MHz)
10
1
1000
100
10
Capacitance (pF)
TZB4Z100
R200
Q
1000
100
200100 400300 500 600
Frequency (MHz)
10
1
1000
100
10
Capacitance (pF)
TZB4R200
R500
Q
1000
100
100 500300 400200
Frequency (MHz)
10
1
1000
100
10
Capacitance (pF)
TZB4R500
T13E.pdf
Aug.10,2012
29
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
7
Temperature (°C)
t3
t2
T3
T2
T5
T4
T1
time (s)
t1
Soldering profile for Lead-free solder (96.5Sn/3Ag/0.5Cu), Eutectic solder (63Sn/37Pb)
Temperature (°C)
t1
t2
T3
T2
T1
time (s)
Limit Profile
Standard Profile
qSoldering profile for Lead-free solder (96.5Sn/3Ag/0.5Cu)
Limit Profile
Standard Profile
s!VAILABLEFORTERMINALSHAPE!"AND%
s)MMERSETHEBODYINSOLDERBATHAVAILABLEFORCOVERFILMTYPE
Standard Profile
Pre-heating Heating
Temp. (T1) Time (t1) Temp. (T2) Time (t2)
1 time150°C 60 to 120sec. 250°C 5sec. max.
Temperature (°C)
time (s)
Standard Profile
t1
T1 t2
T3
T2
wSoldering profile for Eutectic solder (63Sn/37Pb)
(Limit profile: refer to q)
Flow Soldering Profile
Reflow Soldering Profile
Cycle
of reflow
Limit Profile
Pre-heating Heating
Temp. (T1) Time (t1) Temp. (T3) Time (t2)
2 times150°C 60 to 120sec. 265±3°C 5sec. max.
Cycle
of reflow
Standard Profile
Pre-heating Heating
Peak
temperature
(T3)
Cycle
of reflow
Temp. (T1) Time (t1) Temp. (T2) Time (t2)
2 times245±3°C
150 to 180°C 60 to 120sec.
220°C
30 to 60sec.
Limit Profile
Pre-heating Heating Cycle
of reflow
Temp. (T1) Time (t1) Temp. (T4) Time (t3)
2 times
260 +5/-0°C
150 to 180°C 60 to 120sec.
230°C
30 to 50sec.
Peak
temperature
(T5)
Standard Profile
Pre-heating Heating Cycle
of reflow
Temp. (T1) Time (t1) Temp. (T2) Time (t2)
1 time
230 +5/-0°C
150°C
60 to 120sec.
183°C 30sec.
Peak
temperature
(T3)
Soldering Iron
Standard Profile
Temperature of soldering iron tip Soldering time Soldering iron power output
350±10°C 3sec. max. 30W max. 1 time
Cycle of soldering iron
c Temperature Profi le
c Notice (Storage and Operating Conditions)
T13E.pdf
Aug.10,2012
30
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
7
1. Do not use the trimmer capacitor under atmosphere
of RTV silicone rubber (Room Temperature
Vulcanizing Silicone Rubber) except Acetone
liberating silicone sealant.
2. Before using trimmer capacitors, please store under
the conditions of -10 to +40°C and 30 to 85%RH.
3. Do not store in or near corrosive gasses.
4. Use within 6 months of delivery.
5. Do not store under direct sunlight.
6. Do not use the trimmer capacitor under the
conditions listed below.
(1) Corrosive gasses atmosphere
(ex. Chlorine gas, Hydrogen sulfi de gas,
Ammonia gas, Sulfuric acid gas, Nitric oxide gas,
etc.)
(2) In liquid (ex. water, oil, medical liquid,
organic solvent, etc.)
(3) Dusty / dirty atmosphere
(4) Direct sunlight
(5) Static voltage or electric/magnetic fi elds
(6) Direct sea breeze
(7) Other variations of the above
c Notice (Soldering and Mounting)
c Notice (Handling)
1. Use suitable screwdrivers that fi t comfortably in
driver slot.
(1) Recommended screwdriver for manual adjustment
MURATA: KMDR010
(2) Recommended screwdriver bit for automatic
adjustment
MURATA: KMBT010
2. When adjusting with a screwdriver, do not apply
excessive force (preferably 1.0 N [Ref: 100gf] max.)
to minimize capacitance drift. Excessive force applied
to the screwdriver slot may cause deformation of the
products.
3. Do not apply adhesive, lock paints, or any other
substances to the trimmer capacitor to secure the
rotor position. They may cause corrosion or
electrical contact problems.
4. Do not break the cover fi lm before the completion
of PCB mounting, soldering, and cleaning.
5. Do not clean the trimmer capacitor after the cover
fi lm has been broken.
6. To break the cover fi lm, fi rst turn the screwdriver
more than 360°, and set the capacitance value.
(Inserting the screwdriver only will not break the
cover fi lm.)
c Notice (Other)
Before using trimmer capacitors, please test after
assembly in your particular mass production system.
T13E.pdf
Aug.10,2012
31
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
7
1. Soldering
(1) Can be soldered by refl ow soldering method, fl ow
soldering method, and soldering iron.
(2) Soldering conditions
Refer to the temperature profi le.
If the soldering conditions are not suitable, e.g.,
excessive time and/or excessive temperature, the
trimmer capacitor may deviate from the specifi ed
characteristics.
(3) The amount of solder is critical.
(4) The thickness of solder paste should be printed
from 150 micro m to 200 micro m and the dimension
of land pattern should be Murata's standard land
pattern used at refl ow soldering. Insuffi cient
amounts of solder can lead to insuffi cient
soldering strength on PCB. Excessive amounts of
solder may cause bridging between the terminals
or contact failure due to fl ux wicking up.
(5) When using soldering iron, the string solder
shall be applied to the lower part of the
terminal only. Do not apply fl ux except to the
terminals. Excessive amounts of solder and/or
applying solder to the upper part of the
terminal may cause fi xed rotor or contact failure
due to fl ux invasion into the movable part and/or
the contact point. The soldering iron should not
come in contact with the plastic case of the
trimmer capacitor. If such contact does occur,
the trimmer capacitor may be damaged.
(6) Our recommended chlorine content of solder is
as follows.
(a) Solder paste: 0.2wt% max.
(b) String solder: 0.5wt% max.
(7) Do not use water-soluble fl ux (for water
cleaning). To prevent the deterioration of
trimmer capacitor characteristics, apply fl ux
only to terminals.
2. Mounting
(1) Do not apply excessive force (preferably 5.0N
[Ref: 500gf] max.), when the trimmer capacitor
is mounted on the PCB.
(2) Do not warp and/or bend PCB to protect trimmer
capacitor from breakage.
(3) When bending the terminals, do not apply
excessive force to the body of the product to
protect the terminal fi xing part from damage.
(4) Use a pick-up nozzle of a suitable dimension.
> Without cover fi lm type
- External dimensions of 4.5x4.0mm and
2.5mm bore diameter.
> With cover fi lm type
- 4.0mm external diameter and 2.0mm bore
diameter.
3. Cleaning [with cover fi lm type]
Isopropyl alcohol and ethyl alcohol are available
material for cleaning. If you use any other type of
solvent, please evaluate performance in your
application. Moreover, please confi rm that no
damage has occurred to the trimmer capacitor
after cleaning in your conditions.
4. Other
Note the polarity of the trimmer capacitor to
minimize infl uence by stray capacitance.
(Refer to the dimensions concerning the polarity.)
Ceramic Trimmer Capacitors
TZ03 Series
2.5±0.2 dia.
0.5±0.2 Depth 0.5 min.
6 dia.
Tolerance: ±0.5
in mm
4
6
1.0±0.1
1.0±0.1
6.6
0.2±0.05
0.25±0.05
4.83.3
F Type
2.5±0.2 dia.
0.5±0.2 Depth 0.5 min.
6.0 dia.
6.0
1.2±0.1
7.8
6.4
3.0 3.4 1.0±0.1
Tolerance: ±0.5
in mm
0.25±
0.05
0.2±
0.05
4.8 3.0
4.0
N Type
Part Number C min. (max.)
(pF)
C max.
(pF) TC Q Rated Voltage Withstanding Voltage Stator/Case Color
TZ03Z2R3p169
1.25 2.3 +50/-0% NP0±200ppm/°C 300min. at 1MHz, Cmax. 100Vdc 220Vdc Black
TZ03Z050p169
1.5 5.0 +50/-0% NP0±200ppm/°C 500min. at 1MHz, Cmax. 100Vdc 220Vdc Blue
TZ03Z070p169
2.0 7.0 +50/-0% NP0±200ppm/°C 500min. at 1MHz, Cmax. 100Vdc 220Vdc Blue
TZ03Z100p169
2.7 10.0 +50/-0% NP0±200ppm/°C 500min. at 1MHz, Cmax. 100Vdc 220Vdc Blue
TZ03R200p169
4.2 20.0 +50/-0% N750±300ppm/°C 500min. at 1MHz, Cmax. 100Vdc 220Vdc Red
TZ03R300p169
5.2 30.0 +50/-0% N750±300ppm/°C 500min. at 1MHz, Cmax. 100Vdc 220Vdc Green
TZ03P450p169
6.8 45.0 +50/-0% N1200±500ppm/°C 300min. at 1MHz, Cmax. 100Vdc 220Vdc Yellow
TZ03P600p169
9.8 60.0 +50/-0% N1200±500ppm/°C 300min. at 1MHz, Cmax. 100Vdc 220Vdc Brown
TZ03Z500p169
6.0 50.0 +100/-0% NP0±300ppm/°C 300min. at 1MHz, Cmax. 50Vdc 110Vdc Orange
TZ03R900p169
9.0 90.0 +100/-0% N750±300ppm/°C 300min. at 1MHz, Cmax. 50Vdc 110Vdc Black+Dot
TZ03R121p169
10.0 120.0 +100/-0% N750±300ppm/°C 300min. at 1MHz, Cmax. 50Vdc 110Vdc Black
Insulation Resistance: 10000M ohm Torque: 2.0 to 14.7mNm Operating Temperature Range: -25 to +85°C
A blank column is fi lled with terminal type codes.
c Features
1. Color coded case facilitates identifi cation of
capacitance range.
2. Sealed construction prevents the penetration of
fl ux and dust.
3. Available in two adjustment styles: Top/Rear.
4. Cross-shaped (+) slot enables automatic adjustment.
c Applications
1. Car audio systems
2. Car clocks
3. Stereos
4. Radio cassette tape recorders
5. Cordless telephones
6. Video games
7. Compact radio equipment
8. Remote keyless entry systems
9. Burglarproof devices
T13E.pdf
Aug.10,2012
32
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
8
c Construction
1.3±0.1 dia.
1.3±0.1 dia.
5
Tolerance: ±0.5
in mm
c Mounting Holes
F Type
(
Tolerance: ±0.5
in mm
)
1.3±0.1
1.1±0.1
33.3
3 dia.
N Type
+6
+4
+2
20
–25
85
55
–2
–4
–6
Temp. (°C)
0
0
Cap.Change (%)
Z070 (NP0±200ppm/°C)
c Temperature Characteristics
TZ03Z070
+6
+4
+2
20
–25
8555
–2
–4
–6
Temp. (°C)
0
0
Cap.Change (%)
R200 (N750±300ppm/°C)
TZ03R200
+8
+6
+4
+2
20
–25
85
55
–2
–4
–6
Temp. (°C)
0
0
–8
–10
Cap.Change (%)
P600 (N1200±500ppm/°C)
TZ03P600
+8
+6
+4
+2
20
–25
85
55
–2
–4
–6
Temp. (°C)
0
0
–8
–10
Cap.Change (%)
Z500 (NP0±300ppm/°C)
TZ03Z500
Continued on the following page.
T13E.pdf
Aug.10,2012
33
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
8
Continued from the preceding page.
+8
+6
+4
+2
20
–25
8555
–2
–4
–6
Temp. (°C)
0
0
–8
–10
Cap.Change (%)
R121 (N750±300ppm/°C)
c Temperature Characteristics
TZ03R121
1000
100
10
1001200 300 400 500 600 700 800 900 1000
1000
100
10
Q
Frequency (MHz)
Capacitance (pF)
Z070
c Frequency Characteristics
TZ03Z070
1000
100
10
1001200 300 400 500
1000
100
10
Q
Frequency (MHz)
Capacitance (pF)
R200
TZ03R200
1000
100
10
1001200 300 400 500
1000
100
10
Q
Frequency (MHz)
Capacitance (pF)
P450
TZ03P450
1000
100
10
1001200 300 400 500
1000
100
10
Q
Frequency (MHz)
Capacitance (pF)
P600
TZ03P600
Continued on the following page.
T13E.pdf
Aug.10,2012
34
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
8
Continued from the preceding page.
1000
100
10
1001200 300 400 500
1000
100
10
Q
Frequency (MHz)
Capacitance (pF)
R900
c Frequency Characteristics
TZ03R900
Soldering profile for Lead-free solder (96.5Sn/3Ag/0.5Cu), Eutectic solder (63Sn/37Pb)
Temperature (°C)
t1
t2
Pre-heating
Heating
T3
T2
T1
time (s)
Limit Profile
Standard Profile
Standard Profile
Pre-heating Heating
Temp. (T1) Time (t1) Temp. (T2) Time (t2)
1 time150°C 60 to 120sec. 250°C 5sec. max.
Flow Soldering Profile
Cycle
of reflow
Limit Profile
Pre-heating Heating
Temp. (T1) Time (t1) Temp. (T3) Time (t2)
2 times150°C 60 to 120sec. 265±3°C 5sec. max.
Cycle
of reflow
Soldering Iron
Standard Profile
Temperature of soldering iron tip Soldering time Soldering iron power output
350±10°C 3sec. max. 30W max. 1 time
Cycle of soldering iron
c Temperature Profi le
c Notice (Storage and Operating Conditions)
1. Do not use the trimmer capacitor under atmosphere
of RTV silicone rubber (Room Temperature
Vulcanizing Silicone Rubber) except Acetone
liberating silicone sealant.
2. Before using trimmer capacitors, please store under
the conditions of -10 to +40°C and 30 to 85%RH.
3. Do not store in or near corrosive gasses.
4. Use within 6 months of delivery.
5. Open the package just before using.
6. Prior to storing previously opened packages, the
packaging should be heat-sealed. Avoid using
rubber bands for repackaging.
7. Do not store under direct sunlight.
8. Do not use the trimmer capacitor under the
conditions listed below.
(1) Corrosive gasses atmosphere
(ex. Chlorine gas, Hydrogen sulfi de gas,
Ammonia gas, Sulfuric acid gas, Nitric oxide gas,
etc.)
(2) In liquid (ex. water, oil, medical liquid,
organic solvent, etc.)
(3) Dusty / dirty atmosphere
(4) Direct sunlight
(5) Static voltage or electric/magnetic fi elds
(6) Direct sea breeze
(7) Other variations of the above
T13E.pdf
Aug.10,2012
35
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
8
c Notice (Soldering and Mounting)
c Notice (Handling)
c Notice (Other)
Before using trimmer capacitors, please test after
assembly in your particular mass production system.
T13E.pdf
Aug.10,2012
36
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
8
1. Soldering
(1) TZ03 series can be soldered by fl ow soldering
method and soldering iron. Do not use refl ow
soldering method.
(2) Soldering conditions
Refer to the temperature profi le.
If the soldering conditions are not suitable, e.g.,
excessive time and/or excessive temperature,
the trimmer capacitor may deviate from the
specifi ed characteristics.
(3) The dimension of mounting hole should be Murata's
standard mounting hole used at fl ow soldering.
The amount of solder is critical. Insuffi cient
amounts of solder can lead to insuffi cient
soldering strength on PCB. Excessive amounts of
solder may cause bridging between the terminals
or contact failure due to fl ux wicking up.
(4) When using soldering iron, the string solder
shall be applied to the lower part of the
terminal only. Do not apply fl ux except to the
terminals. Excessive amounts of solder and/or
applying solder to the upper part of the
terminal may cause fi xed rotor or the contact
failure due to fl ux invasion into the movable
part and/or the contact point. The soldering
iron should not come in contact with the plastic
case of the trimmer capacitor. If such contact
does occur, the trimmer capacitor may be damaged.
(5) Our recommended chlorine content of string
solder is 0.5wt% max.
(6) Do not use water-soluble fl ux (for water cleaning).
To prevent the deterioration of trimmer
capacitor characteristics, apply fl ux only to
terminals.
2. Mounting
(1) Do not apply excessive force (preferably 5.0 N
[Ref: 500gf] max.), when the trimmer capacitor
is mounted on the PCB.
(2) Use the suitable PCB holes that are the same
pitch as the terminal of the trimmer capacitor.
If it does not fi t the terminal, excessive stress
may be applied to the terminal and the trimmer
capacitor may deviate from the specifi ed
characteristics.
(3) Do not apply bending stress more than 10.0N
(Ref: 1kgf) after the trimmer capacitor has
been mounted on the PCB.
(4) Mount trimmer capacitor in contact with PCB.
(5) When bending the terminals, do not apply
excessive force to the body of the product to
protect the terminal fi xing part from damage.
3. Cleaning
Isopropyl alcohol and ethyl alcohol are available
material for cleaning. If you use any other type
of solvents, please evaluate performance in
your application. Moreover, please confi rm that
no damage has occurred to the trimmer capacitor
after cleaning in your conditions.
4. Other
Note the polarity of the trimmer capacitor to
minimize infl uence by stray capacitance.
(Refer to the dimensions concerning the polarity.)
1. Use suitable screwdrivers that fi t comfortably in
driver slot.
(1) Recommended screwdriver for manual adjustment
MURATA: KMDR010
(2) Recommended screwdriver bit for automatic
adjustment
MURATA: KMBT010
2. When adjusting with a screwdriver, do not apply
excessive force (preferably 1.0 N [Ref: 100gf] max.)
to minimize capacitance drift. Excessive force applied
to the screwdriver slot may cause deformation of the
products.
3. Do not apply adhesive, lock paints, or any other
substances to the trimmer capacitor to secure the
rotor position. They may cause corrosion or
electrical contact problems.
Packaging
Part Number
TZR1
TZS2
TZY2
TZV2
TZC3
TZW4
TZB4
TZ03
3000
3000
2000
2000
1000
500
500
-
ø180mm Reel
-
-
-
-
-
-
2500
-
ø330mm Reel
500
500
500
500
500
100
500
1000
Bulk
Minimum Quantity (pcs.)
c Minimum Quantity
4.0±0.1
8.0±0.3
2.0±0.1
4.0±0.1
1.5 dia.
+0.1
-0
2.0±0.2
1.75±0.1
3.5±0.1
1.8±0.2
1.05±0.2
0.25±0.1
(in mm)
c Tape Dimensions
TZR1 Series
4.0±0.1
8.0±0.3
2.0±0.1
4.0±0.1
1.5 -0 dia.
+0.1
3.0±0.2
1.75±0.1
3.5±0.1
2.5±0.2
1.25±0.2
0.25±0.1
(in mm)
TZS2 Series
1.5 +0.1
– 0 dia. 2.0 4.0
A
A
2.7±0.2
4.0
3.5
0.25
t
8.0±0.2
1.75
A-Across
section
t=TZY2 (TZVY2) : 1.6±0.2
TZV2 (TZV02) : 1.9±0.2
3.6±0.2
Tolerance: ±0.1
in mm
TZY2/TZV2 Series
1.5 +0.1
– 0 dia.
4.9±0.2
A
2
8
4
5.5 1.75
12±0.3
0.3
2.0±0.2
A
A-Across
section
Tolerance : ±0.1
in mm
3.6±0.2
TZC3 Series
12±0.2
1.5 +0.1
– 0 dia.
5.6
A
2
8
4
5.5 1.75
0.3
2.6
A
A-Across
section
Tolerance: ±0.1
in mm
4.6
TZW4 Series
1.5 +0.1
– 0 dia.
8.0 2.0 4 .0
A
A
1.8
4.3
3.55±0.2
4.8
7.5
5.5
12.0±0.3
0.3±0.1
A-Across
section
Direction of feed
Tolerance: ±0.1
in mm
1.75
TZB4 Series
Continued on the following page.
T13E.pdf
Aug.10,2012
37
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
Packaging
Continued from the preceding page.
(in mm)
13.0±0.5 dia.
21.0±0.8 dia.
2.0±0.5
178±2 dia.
9.0±1.0
50 min.
13.0±1.0
c Reel Dimensions (180mm diameter)
TZR1/TZS2/TZY2/TZV2 Series
(in mm)
13.0±0.5 dia.
21.0±0.8 dia.
2.0±0.5
178±2 dia.
13.0±1.0
50 min.
17.0±1.0
TZC3/TZW4/TZB4 Series
(in mm)
13.0±0.5 dia.
21.0±0.8 dia.
2.0±0.5
328±2 dia.
13.5±1.0
50 min.
17.5±1.0
c Reel Dimensions (330mm diameter)
TZB4 Series
T13E.pdf
Aug.10,2012
38
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
Recommended Adjustment Tools
c For Manual Adjustment
Series MURATA
Model Number
Manufacturer’s
Model Number Shape
TZR1
TZS2
TZY2
TZV2
TZC3
TZB4
TZ03
TZW4
KMDR160
KMDR050
KMDR060
KMDR020
KMDR010
KMDR130
MURATA MFG.
KMDR160
MURATA MFG.
KMDR050
ENGINEER INC.
DA-89
VESSEL MFG.
NO.9000 -0.9g30
MURATA MFG.
KMDR010
VESSEL MFG.
NO.9000 -1.3g30
Please use the following recommended screwdrivers.
You can order these drivers using the part numbers below.
Although you can also adjust the capacitance value using commercial products, please use one with the same head size as the
driver listed below.
Continued on the following page.
1.5
80
Bit shape: Minus (0.3x0.13)
(in mm)
(in mm)
Bit shape: Square (0.54x0.54)
80
1.5
18
108
(in mm)
Bit shape: Minus (0.8x0.35)
(in mm)
9000
0.9-30
15
125
Bit shape: Minus (0.9x0.4)
(in mm)
50
122
20
Bit shape: Minus (2.2x0.4)
(in mm)
125
15
9000
1.3-30
CERAMIC BLADE
ELECTRONICS
Bit shape: Minus (1.3x30)
T13E.pdf
Aug.10,2012
39
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
Recommended Adjustment Tools
c For Automatic Adjustment
TZS2
TZY2
TZV2
TZC3
TZB4
TZ03
KMBT050
KMBT060
KMBT020
KMBT010
MURATA MFG.
KMBT050
MURATA MFG.
KMBT060
MURATA MFG.
KMBT020
MURATA MFG.
KMBT010
Continued from the preceding page.
Series MURATA
Model Number
Manufacturer’s
Model Number Shape
(in mm)
20
1.8 dia.
2
Bit shape: Square (0.54x0.54)
(in mm)
25
2.4 dia.
0.6
Bit shape: Minus (0.56x0.25)
(in mm)
25
0.6
2.4 dia.
Bit shape: Minus (0.9x0.4)
(in mm)
30
2.2 dia.
Bit shape: Minus (2.2x0.4)
T13E.pdf
Aug.10,2012
40
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
T13E.pdf
Aug.10,2012
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
MURATA FACTORY
Sabae Murata Mfg. Co., Ltd.
The products listed herein have been produced
by a QS9000 and ISO9001 certified factory
∗ No ODCs (Ozone Depleting Chemicals) are used on
any Murata trimmer potentiometers.
Qualified Standards
41
!Note T13E.pdf
Aug.10,2012
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.