Data Sheet
February 2, 2011
QPW050/060 Series DC-DC Converter Power Modules:
36-75Vdc Input; 1.2Vdc to 3.3Vdc Output; 50A/60A Output Current
* UL is a registered trademark of Underwriters Laboratories, Inc.
† CSA is a registered trademark of Canadian Standards Association.
‡ VDE is a trademark of Verband Deutscher Elektrotechniker e.V.
** ISO is a registered trademark of the International Organization of Standards
Document No: DS03-075 ver 1.16
PDF name: QPW Series.pdf
Features
Compliant to RoHS EU Directive 2002/95/EC (-Z
versions)
Compliant to ROHS EU Directive 2002/95/EC with lead
solder exemption (non-Z versions)
Delivers up to 60A output current
Improved Thermal Performance: 30A at 70ºC at 1m/s
(200LFM) for 3.3Vo
High power density: 119W/in3
High efficiency – 93% at 3.3V full load
Low output voltage- supports migration to future IC
supply voltages down to 1.0V
Industry standard Quarter brick:
57.9 mm x 36.8 mm x 10.6 mm
(2.28 in x 1.45 in x 0.42 in)
Single tightly regulated output
2:1 input voltage range
Constant Switching frequency
Negative Remote On/Off logic
Output overcurrent/voltage/temperature protection
Output Voltage adjustment (±10%)
Wide operating temperature range (-40°C to 85°C)
Meets the voltage insulation requirements for
ETSI 300-132-2 and complies with and is licensed for
Basic Insulation rating per EN60950-1
CE mark meets 73/23/EEC and 93/68/EEC directives§
UL* 60950-1, 2nd Ed. Recognized, CSA† C22.2 No.
60950-1-07 Certified, and VDE‡ (EN60950-1, 2nd Ed.)
Licensed
ISO** 9001 certified manufacturing facilities
Applications
Distributed power architectures
Wireless Networks
Access and Optical Network Equipment
Enterprise Networks
Latest generation IC’s (DSP, FPGA, ASIC)
and Microprocessor powered applications
Options
Positive Remote On/Off logic
Case ground pin (-H Baseplate option)
Auto restart after fault shutdown
Description
The QPW-series dc-dc converters are a new generation of DC/DC power modules designed for maximum efficiency
and power density. The QPW series provide up to 60A output current in an industry standard quarter brick. The
converter incorporates synchronous rectification technology and innovative packaging techniques to achieve ultra
high efficiency reaching 93% at 3.3V full load. The ultra high efficiency of this converter leads to lower power
dissipation such that for most applications a heat sink is not required. The QPW series power modules are isolated
dc-dc converters that operate over a wide input voltage range of 36 to 75 Vdc and provide single precisely regulated
output. The output is fully isolated from the input, allowing versatile polarity configurations and grounding
connections.
RoHS Compliant
Data Sheet
February 2, 2011 QPW050/060 Series Power Modules; DC-DC converters
36-75Vdc Input; 1.2Vdc to 3.3Vdc Output
LINEAGE POWER 2
Absolute Maximum Ratings
Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are
absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in
excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for
extended periods can adversely affect the device reliability.
Parameter Device Symbol Min Max Unit
Input Voltage
Continuous VIN -0.3 80 Vdc
Transient (100ms) VIN, trans -0.3 100 Vdc
Operating Ambient Temperature All TA -40 85 °C
(see Thermal Considerations section)
Storage Temperature All Tstg -55 125 °C
I/O Isolation Voltage (100% factory Hi-Pot tested) All 1500 Vdc
Electrical Specifications
Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature
conditions.
Parameter Device Symbol Min Typ Max Unit
Operating Input Voltage VIN 36 48 75 Vdc
Maximum Input Current IIN,max 6 Adc
(VIN=0V to 60V, IO=IO, max)
Inrush Transient All I2t 1 A2s
Input Reflected Ripple Current, peak-to-peak
(5Hz to 20MHz, 12μH source impedance; VIN=0V to
75V, IO= IOmax ; see Figure 31)
All 7 mAp-p
Input Ripple Rejection (120Hz) All 50 dB
CAUTION: This power module is not internally fused. An input line fuse must always be used.
This power module can be used in a wide variety of applications, ranging from simple standalone operation to an
integrated part of a sophisticated power architecture. To preserve maximum flexibility, internal fusing is not included,
however, to achieve maximum safety and system protection, always use an input line fuse. The safety agencies
require a fast-acting fuse with a maximum rating of 15A (see Safety Considerations section). Based on the
information provided in this data sheet on inrush energy and maximum dc input current, the same type of fuse with a
lower rating can be used. Refer to the fuse manufacturer’s data sheet for further information.
Data Sheet
February 2, 2011 QPW050/060 Series Power Modules; DC-DC converters
36-75Vdc Input; 1.2Vdc to 3.3Vdc Output
LINEAGE POWER 3
Electrical Specifications (continued)
Parameter Device Symbol Min Typ Max Unit
Output Voltage Set-point
(VIN=VIN,nom, IO=IO, max, Tc =25°C)
3.3V
2.5V
1.8V
1.5V
1.2V
VO, set
3.24
2.45
1.77
1.47
1.18
3.30
2.25
1.80
1.50
1.20
3.36
2.55
1.83
1.53
1.22
Vdc
Output Voltage
(Over all operating input voltage, resistive load, and
temperature conditions until end of life)
3.3V
2.5V
1.8V
1.5V
1.2V
VO
3.20
2.42
1.74
1.44
1.15
3.40
2.57
1.86
1.56
1.25
Vdc
Output Regulation
Line (VIN=VIN, min to VIN, max) All
0.05 0.2 %Vo
Load (IO=IO, min to IO, max) All
0.05 0.2 %Vo
Temperature (Tc = -40ºC to +85ºC) All 15 50 mV
Output Ripple and Noise on nominal output
(VIN=VIN, nom and IO=IO, min to IO, max)
RMS (5Hz to 20MHz bandwidth) All 30 mVrms
Peak-to-Peak (5Hz to 20MHz bandwidth) All 100 mVpk-pk
External Capacitance 3.3V – 1.5V CO, max 6,800 μF
1.2V CO, max 22,000 μF
Output Current 3.3V Io 0 50 Adc
2.5V – 1.2V Io 0 60 Adc
Output Current Limit Inception 3.3V IO, lim 58 Adc
2.5V – 1.2V IO, lim 69 Adc
Efficiency
VIN=VIN, nom, Tc=25°C
IO=IO, max , VO= VO,set
3.3V
2.5V
1.8V
1.5V
1.2V
η
η
η
η
η
__
__
__
__
93
91
89
87
85
__
__
__
__
%
%
%
%
%
Switching Frequency fsw 300 kHz
Dynamic Load Response
(Io/t=1A/10s; Vin=Vin,nom; Tc=25°C; Tested
with a 10 μF aluminum and a 1.0 μF ceramic
capacitor across the load.)
Load Change from Io= 50% to 75% of Io,max:
Peak Deviation
Settling Time (Vo<10% peak deviation)
All Vpk
ts
__
4
200
__
%VO, set
s
Load Change from Io= 75% to 50% of Io,max:
Peak Deviation V
pk __ 4 __ %VO, set
Settling Time (Vo<10% peak deviation) ts 200 s
Isolation Specifications
Parameter Symbol Min Typ Max Unit
Isolation Capacitance Ciso 2700 pF
Isolation Resistance Riso 10 MΩ
General Specifications
Parameter Device Min Typ Max Unit
Calculated MTBF (IO=80% of IO, max, Tc =40°C,
airflow=1m/s(200LFM)) All 1,204,000 Hours
Weight 42 (1.48) g (oz.)
Data Sheet
February 2, 2011 QPW050/060 Series Power Modules; DC-DC converters
36-75Vdc Input; 1.2Vdc to 3.3Vdc Output
LINEAGE POWER 4
Feature Specifications
Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature
conditions. See Feature Descriptions for additional information.
Parameter Device Symbol Min Typ Max Unit
Remote On/Off Signal Interface
(VIN=VIN, min to VIN, max ; open collector or
equivalent,
Signal referenced to VIN- terminal)
Negative Logic: device code suffix “1”
Logic Low = module On, Logic High = module Off
Positive Logic: No device code suffix required
Logic Low = module Off, Logic High = module On
Logic Low Specification
Remote On/Off Current – Logic Low All Ion/off 0.15 1.0 mA
On/Off Voltage:
Logic Low All Von/off 0.0 1.2 V
Logic High – (Typ = Open Collector) All Von/off __ 15 V
Logic High maximum allowable leakage current All Ion/off 50 μA
Turn-On Delay and Rise Times
(IO=IO, max)
Tdelay = Time until VO = 10% of VO,set from either
application of Vin with Remote On/Off set to On
or operation of Remote On/Off from Off to On
with Vin already applied for at least one second.
3.3V Tdelay 2.5 ms
Trise 12 ms
2.5V – 1.2V Tdelay 2.5 ms
Trise = time for VO to rise from 10% of VO,set to
90% of VO,set. Trise 1.5 ms
Output Voltage Adjustment
(See Feature Descriptions):
Output Voltage Remote-sense Range
Output Voltage Set-point Adjustment Range (trim)
Vsense
__
90
__
__
10
110
%Vo,nom
%Vo,nom
Output Overvoltage Protection 3.3V VO, limit 4.0 4.9 V
2.5V
3.0 3.4 V
1.8V
2.1 2.4 V
1.5V
1.8 2.2 V
1.2V
1.5 1.8 V
Overtemperature Protection All Tref 110 °C
(See Feature Descriptions)
Input Undervoltage Lockout VIN, UVLO
Turn-on Threshold All 34.5 36 V
Turn-off Threshold All 30 32
V
Data Sheet
February 2, 2011 QPW050/060 Series Power Modules; DC-DC converters
36-75Vdc Input; 1.2Vdc to 3.3Vdc Output
5
Characteristic Curves
The following figures provide typical characteristics for the QPW050A0F (3.3V, 50A) at 25ºC. The figures are identical
for either positive or negative Remote On/Off logic.
INPUT CURRENT, Ii (A)
OUTPUT VOLTAGE, On/Off VOLTAGE
VO (V) (5V/div) VON/OFF(V) (2V/div)
INPUT VOLTAGE, VO (V) TIME, t (5 ms/div)
Figure 1. Typical Input Characteristic at Room
Temperature. Figure 4. Typical Start-Up Using Remote On/Off,
negative logic versi on show n.
EFFCIENCY, η (%)
OUTPUT CURRENT, OUTPUT VOLTAGE
IO (A) (10A/div) VO (V) (100mV/div)
OUTPUT CURRENT, IO (A) TIME, t (100 μs/div)
Figure 2. Typi cal Conv erter Effici ency Vs. Output
current at Room Temperature. Figure 5. Typical Transient Resp onse to Step
chang e in Load from 50% to 25% of
Full Load at Room Temperature and 48
Vdc Input.
OUTPUT VOLTAGE,
VO (V) (50mV/div)
OUTPUT CURRENT, OUTPUT VOLTAGE
IO (A) (10A/div) VO (V) (100mV/div)
TIME, t (1s/div) TIME, t (100 μs/div)
Figure 3. Typical Output Ripple and Noise at Room
Temperat ure and Io = Io, max. Figure 6. Typical Tra nsient Response to Step change
in Load from 50% to 75% of Full Load at Room
Temperature and 48 V dc Input .
36 Vin
48 Vin
75 Vin
0
1
2
3
4
5
6
25 35 45 55 65 75
Io = 0 A
Io = 25 A
Io = 50 A
80
82
84
86
88
90
92
94
0 10203040 50
Vi = 36 V
Vi = 48 V
Vi = 75 V
Data Sheet
February 2, 2011 QPW050/060 Series Power Modules; DC-DC converters
36-75Vdc Input; 1.2Vdc to 3.3Vdc Output
LINEAGE POWER 6
Characteristic Curves
The following figures provide typical characteristics for the QPW060A0G (2.5V, 60A) at 25ºC. The figures are
identical for either positive or negative Remote On/Off logic.
INPUT CURRENT, Ii (A)
OUTPUT VOLTAGE, On/Off VOLTAGE
VO (V) (5V/div) VON/OFF(V) (1V/div)
INPUT VOLTAGE, VO (V) TIME, t (2.5 ms/div)
Figure 7. Typical Input Characteristic at Room
Temperature. Figure 10. Typical Start-Up Using Rem ote On/Off,
negative logic versi on show n.
EFFCIENCY, η (%)
OUTPUT CURRENT, OUTPUT VOLTAGE
IO (A) (10A/div) VO (V) (50mV/div)
OUTPUT CURRENT, IO (A) TIME, t (500 μs/div)
Figure 8. Typi cal Conv erter Effici ency Vs. Output
current at Room Temperature. Figure 11. Typical Transient Response to Step
change in Load from 50% to 25%of Full Load at
Room Temperature and 48 Vdc Input.
OUTPUT VOLTAGE,
VO (V) (50mV/div)
OUTPUT CURRENT, OUTPUT VOLTAGE
IO (A) (10A/div) VO (V) (50mV/div)
TIME, t (2.5s/div) TIME, t (500 μs/div)
Figure 9. Typical Output Ripple and Noise at Room
Temperat ure and Io = Io, max. Figure 12. Typical Transient Response to Step change
in Load from 50% to 75% of Full Load at Room
Temperature and 48 V dc Input .
36 Vin
48 Vin
75 Vin
0
1
2
3
4
5
6
25 35 45 55 65 75
Io = 60A
Io = 0 A
Io = 30 A
84
86
88
90
92
94
5 1015202530354045505560
Vi = 36 V
Vi = 48 V
Vi = 75 V
Data Sheet
February 2, 2011 QPW050/060 Series Power Modules; DC-DC converters
36-75Vdc Input; 1.2Vdc to 3.3Vdc Output
LINEAGE POWER 7
Characteristic Curves
The following figures provide typical characteristics for the QPW060A0Y (1.8V, 60A) at 25ºC. The figures are
identical for either positive or negative Remote On/Off logic.
INPUT CURRENT, Ii (A)
OUTPUT VOLTAGE On/Off VOLTAGE
VO (V) (5V/div) VON/OFF(V) (0.5V/div)
INPUT VOLTAGE, VO (V) TIME, t (2.5 ms/div)
Figure 13. Typical Input Characteristic at Room
Temperature. Figure 16. Typical Start-Up Using Rem ote On/Off,
negative logic versi on show n.
EFFCIENCY, η (%)
OUTPUT CURRENT, OUTPUT VOLTAGE
IO (A) (10A/div) VO (V) (50mV/div)
OUTPUT CURRENT, IO (A) TIME, t (500 μs/div)
Figure 14. Typical Converter Efficiency Vs. Output
current at Room Temperature. Figure 17. Typical Transient Response to Step
chang e in Load from 50% to 25%of Full Load at
Room Temperature and 48 Vdc Input.
OUTPUT VOLTAGE,
VO (V) (20mV/div)
OUTPUT CURRENT, OUTPUT VOLTAGE
IO (A) (10A/div) VO (V) (50mV/div)
TIME, t (2.5s/div) TIME, t (500 μs/div)
Figure 15. Typical Output Ripple and Noise at Room
Temperat ure and Io = Io, max. Figure 18. Typical Transient Response to Step change
in Load from 50% to 75% of Full Load at Room
Temperature and 48 V dc Input .
36 Vin
48 Vin
75 Vin
0
0.5
1
1.5
2
2.5
3
3.5
4
25 35 45 55 65 75
Io = 0 A
Io = 30 A
Io = 60 A
81
83
85
87
89
91
5 1015202530354045505560
Vi = 36 V
Vi = 48 V
Vi = 75 V
Data Sheet
February 2, 2011 QPW050/060 Series Power Modules; DC-DC converters
36-75Vdc Input; 1.2Vdc to 3.3Vdc Output
LINEAGE POWER 8
Characteristic Curves
The following figures provide typical characteristics for the QPW060A0M (1.5V, 60A) at 25ºC. The figures are
identical for either positive or negative Remote On/Off logic.
INPUT CURRENT, Ii (A)
OUTPUT VOLTAGE On/Off VOLTAGE
VO (V) (5V/div) VON/OFF(V) (0.5V/div)
INPUT VOLTAGE, VO (V) TIME, t (2.5 ms/div)
Figure 19. Typical Input Characteristic at Room
Temperature. Figure 22. Typical Start-Up Using Rem ote On/Off,
negative logic versi on show n.
EFFCIENCY, η (%)
OUTPUT CURRENT, OUTPUT VOLTAGE
IO (A) (10A/div) VO (V) (50mV/div)
OUTPUT CURRENT, IO (A) TIME, t (500 μs/div)
Figure 20. Typical Converter Efficiency Vs. Output
current at Room Temperature. Figure 23. Typical Transient Response to Step
chang e in Load from 50% to 25%of Full Load at
Room Temperature and 48 Vdc Input.
OUTPUT VOLTAGE,
VO (V) (20mV/div)
OUTPUT CURRENT, OUTPUT VOLTAGE
IO (A) (10A/div) VO (V) (50mV/div)
TIME, t (2.5s/div) TIME, t (500 μs/div)
Figure 21. Typical Output Ripple and Noise at Room
Temperat ure and Io = Io, max. Figure 24. Typical Transient Response to Step change
in Load from 50% to 75% of Full Load at Room
Temperature and 48 V dc Input .
36 Vin
48 Vin
75 Vin
0
0.5
1
1.5
2
2.5
3
3.5
25 35 45 55 65 75
Io = 0 A
Io = 30 A
Io = 60 A
81
83
85
87
89
91
5 1015202530354045505560
Vi = 36 V
Vi = 75 V
Vi = 48 V
Data Sheet
February 2, 2011 QPW050/060 Series Power Modules; DC-DC converters
36-75Vdc Input; 1.2Vdc to 3.3Vdc Output
LINEAGE POWER 9
Characteristic Curves
The following figures provide typical characteristics for the QPW060A0P (1.2V, 60A) at 25ºC. The figures are
identical for either positive or negative Remote On/Off logic.
INPUT CURRENT, Ii (A)
OUTPUT VOLTAGE On/Off VOLTAGE
VO (V) (5V/div) VON/OFF(V) (0.5V/div)
INPUT VOLTAGE, VO (V) TIME, t (2.5 ms/div)
Figure 25. Typical Input Characteristic at Room
Temperature. Figure 28. Typical Start-Up Using Rem ote On/Off,
negative logic versi on show n.
EFFCIENCY, η (%)
OUTPUT CURRENT, OUTPUT VOLTAGE
IO (A) (10A/div) VO (V) (50mV/div)
OUTPUT CURRENT, IO (A) TIME, t (500 μs/div)
Figure 26. Typical Converter Efficiency Vs. Output
current at Room Temperature. Figure 29. Typical Transient Response to Step
chang e in Load from 5 0% to 25%of F ull Load at
Room Temperature and 48 Vdc Input.
OUTPUT VOLTAGE,
VO (V) (20mV/div)
OUTPUT CURRENT, OUTPUT VOLTAGE
IO (A) (10A/div) VO (V) (50mV/div)
TIME, t (2.5s/div) TIME, t (500 μs/div)
Figure 27. Typical Output Ripple and Noise at Room
Temperat ure and Io = Io, max. Figure 30. Typical Transient Response to Step change
in Load from 50% to 75% of Full Load at Room
Temperature and 48 V dc Input .
36 Vin
48 Vin
75 Vin
0
0.5
1
1.5
2
2.5
3
25 35 45 55 65 75
Io = 0 A
Io = 30 A
Io = 60 A
80
81
82
83
84
85
86
87
88
89
90
5 1015202530354045505560
Vi = 36 V
Vi = 48 V
Vi = 75 V
Data Sheet
February 2, 2011 QPW050/060 Series Power Modules; DC-DC converters
36-75Vdc Input; 1.2Vdc to 3.3Vdc Output
LINEAGE POWER 10
Test Configurations
Note: Measure input reflected-ripple current with a simulated
source inductance (LTEST) of 12 µH. Capacitor CS offsets
possible battery impedance. Measure current as shown
above.
Figure 31. Input Reflected Ripple Current Test
Setup.
Note: Use a 1.0 µF ceramic capacitor and a 10 µF aluminum
or tantalum capacitor. Scope measurement should be made
using a BNC socket. Position the load between 51 mm and
76 mm (2 in. and 3 in.) from the module.
Figure 32. Output Ripple and Noise Test Setup.
LOAD
CONTACT AND
SUPPLY
I
I
CONTACT
V
I
(+)
V
I
(–)
V
O1
DISTRIBUTION LOSSES
RESISTANCE
I
O
V
O2
Note: All measurements are taken at the module terminals.
When socketing, place Kelvin connections at module
terminals to avoid measurement errors due to socket contact
resistance.
Figure 33. Outp ut Voltage and Effici en cy Test
Setup.
Design Considerations
Input Source Impedance
The power module should be connected to a low
ac-impedance source. A highly inductive source
impedance can affect the stability of the power
module. For the test configuration in Figure 31, a
100μF electrolytic capacitor (ESR<0.7 at 100kHz),
mounted close to the power module helps ensure the
stability of the unit. Consult the factory for further
application guidelines.
Output Capacitance
High output current transient rate of change (high
di/dt) loads may require high values of output
capacitance to supply the instantaneous energy
requirement to the load. To minimize the output
voltage transient drop during this transient, low E.S.R.
(equivalent series resistance) capacitors may be
required, since a high E.S.R. will produce a
correspondingly higher voltage drop during the
current transient.
Output capacitance and load impedance interact with
the power module’s output voltage regulation control
system and may produce an ’unstable’ output
condition for the required values of capacitance and
E.S.R.. Minimum and maximum values of output
capacitance and of the capacitor’s associated E.S.R.
may be dictated, depending on the module’s control
system.
The process of determining the acceptable values of
capacitance and E.S.R. is complex and is load-
dependant. Lineage Power provides Web-based tools
to assist the power module end-user in appraising
and adjusting the effect of various load conditions and
output capacitances on specific power modules for
various load conditions.
Safety Considerations
For safety agency approval the power module must
be installed in compliance with the spacing and
separation requirements of the end-use safety agency
standards, i.e., UL 60950-1 2nd, CSA C22.2 No.
60950-1-07, DIN EN 60950-1:2006 + A11 (VDE0805
Teil 1 + A11):2009-11; EN 60950-1:2006 + A11:2009-
03. For the converter output to be considered meeting
the requirements of safety extra-low voltage (SELV),
the input must meet SELV requirements.
If the input source is non-SELV (ELV or a hazardous
voltage greater than 60 Vdc and less than or equal to
75Vdc), for the module’s output to be considered as
meeting the requirements for safety extra-low voltage
(SELV), all of the following must be true:
Data Sheet
February 2, 2011 QPW050/060 Series Power Modules; DC-DC converters
36-75Vdc Input; 1.2Vdc to 3.3Vdc Output
LINEAGE POWER 11
Safety Considerations (continued)
The input source is to be provided with reinforced
insulation from any other hazardous voltages,
including the ac mains.
One VIN pin and one VOUT pin are to be
grounded, or both the input and output pins are
to be kept floating.
The input pins of the module are not operator
accessible.
Another SELV reliability test is conducted on the
whole system (combination of supply source and
subject module), as required by the safety
agencies, to verify that under a single fault,
hazardous voltages do not appear at the
module’s output.
Note: Do not ground either of the input pins of the
module without grounding one of the output
pins. This may allow a non-SELV voltage to
appear between the output pins and ground.
The power module has extra-low voltage (ELV)
outputs when all inputs are ELV.
For input voltages exceeding –60 Vdc but less than or
equal to –75 Vdc, these converters have been
evaluated to the applicable requirements of BASIC
INSULATION between secondary DC MAINS
DISTRIBUTION input (classified as TNV-2 in Europe)
and unearthed SELV outputs.
The input to these units is to be provided with a
maximum 15A fast-acting (or time-delay) fuse in the
unearthed lead.
Data Sheet
February 2, 2011 QPW050/060 Series Power Modules; DC-DC converters
36-75Vdc Input; 1.2Vdc to 3.3Vdc Output
LINEAGE POWER 12
Feature Descriptions
Overcurrent Protection
To provide protection in a fault output overload
condition, the module is equipped with internal
current-limiting circuitry and can endure current limit
for few seconds. If overcurrent persists for few
seconds, the module will shut down and remain latch-
off. The overcurrent latch is reset by either cycling the
input power or by toggling the on/off pin for one
second. If the output overload condition still exists
when the module restarts, it will shut down again. This
operation will continue indefinitely until the
overcurrent condition is corrected.
An auto-restart option is also available.
Remote On/Off
Two remote on/off options are available. Positive logic
remote on/off turns the module on during a logic-high
voltage on the ON/OFF pin, and off during a logic low.
Negative logic remote on/off turns the module off
during a logic high and on during a logic low. Negative
logic, device code suffix "1," is the factory-preferred
configuration. To turn the power module on and off,
the user must supply a switch to control the voltage
between the on/off terminal and the VI (-) terminal
(Von/off). The switch can be an open collector or
equivalent (see Figure 34). A logic low is Von/off = 0
V to I.2 V. The maximum Ion/off during a logic low is 1
mA. The switch should maintain a logic-low voltage
while sinking 1 mA. During a logic high, the maximum
Von/off generated by the power module is 15 V. The
maximum allowable leakage current of the switch at
Von/off = 15V is 50 µA. If not using the remote on/off
feature, perform one of the following to turn the unit
on:
For negative logic, short ON/OFF pin to VI(-).
For positive logic: leave ON/OFF pin open.
Figure 34. Remote On/Off Implementation.
Remote Sense
Remote sense minimizes the effects of distribution
losses by regulating the voltage at the remote-sense
connections. The voltage between the remote-sense
pins and the output terminals must not exceed the
output voltage sense range given in the Feature
Specifications table i.e.:
[Vo(+) – Vo(-)] – [SENSE(+) – SENSE(-)] % of
Vo,nom.
The voltage between the Vo(+) and Vo(-) terminals
must not exceed the minimum output overvoltage
shut-down value indicated in the Feature
Specifications table. This limit includes any increase
in voltage due to remote-sense compensation and
output voltage set-point adjustment (trim). See Figure
35. If not using the remote-sense feature to regulate
the output at the point of load, then connect
SENSE(+) to Vo(+) and SENSE(-) to Vo(-) at the
module.
Although the output voltage can be increased by both
the remote sense and by the trim, the maximum
increase for the output voltage is not the sum of both.
The maximum increase is the larger of either the
remote sense or the trim. The amount of power
delivered by the module is defined as the voltage at
the output terminals multiplied by the output current.
When using remote sense and trim: the output
voltage of the module can be increased, which at the
same output current would increase the power output
of the module. Care should be taken to ensure that
the maximum output power of the module remains at
or below the maximum rated power.
Figure 35. Effective Circuit Configuration for
Single-Module Remote-Sense Operation Output
Voltage.
Output Voltage Set-Point Adjustment (Trim)
Trimming allows the user to increase or decrease the
output voltage set point of a module. This is
accomplished by connecting an external resistor
between the TRIM pin and either the SENSE(+) or
SENSE(-) pins. The trim resistor should be positioned
close to the module.
If not using the trim feature, leave the TRIM pin open.
With an external resistor between the TRIM and
SENSE(-) pins (Radj-down), the output voltage set
point (Vo,adj) decreases (see Figure 36). The
following equation determines the required external
resistor value to obtain a percentage output voltage
change of %.
Data Sheet
February 2, 2011 QPW050/060 Series Power Modules; DC-DC converters
36-75Vdc Input; 1.2Vdc to 3.3Vdc Output
LINEAGE POWER 13
Feature Description (continued)
Output Voltage Set-Point Adjustment (Trim)
For output voltages: 1.5V – 3.3V
KR downadj 2.10
%
510
For output voltage: 1.2V
KR downadj 49.33
%1.1299
Where,
100% ,
,
nomo
desirednomo
VVV
Vdesired = Desired output voltage set point (V).
With an external resistor connected between the
TRIM and SENSE(+) pins (Radj-up), the output
voltage set point (Vo,adj) increases (see Figure 37).
The following equation determines the required
external-resistor value to obtain a percentage output
voltage change of %.
For output voltages: 1.5V – 3.3V
K
V
Rnomo
upadj 2.10
%
510
%*225.1 %100**1.5 ,
For output voltage: 1.2V
K
V
Rnomo
upadj 49.33
%1.1299
%*6.0 %100**769.9 ,
Where,
100% ,
,
nomo
nomodesired
VVV
Vdesired = Desired output voltage set point (V).
The voltage between the Vo(+) and Vo(-) terminals
must not exceed the minimum output overvoltage
shut-down value indicated in the Feature
Specifications table. This limit includes any increase
in voltage due to remote-sense compensation and
output voltage set-point adjustment (trim). See Figure
35.
Although the output voltage can be increased by both
the remote sense and by the trim, the maximum
increase for the output voltage is not the sum of both.
The maximum increase is the larger of either the
remote sense or the trim.
The amount of power delivered by the module is
defined as the voltage at the output terminals
multiplied by the output current. When using remote
sense and trim, the output voltage of the module can
be increased, which at the same output current would
increase the power output of the module. Care should
be taken to ensure that the maximum output power of
the module remains at or below the maximum rated
power.
Figure 36. Circuit Configuration to Decrease
Output Voltage .
Figure 37. Circuit Configuration to Increase
Output Voltage.
Examples:
To trim down the output of a nominal 3.3V
module (QPW050A0F) to 3.1V
100
3.3 1.33.3
%
VVV
∆% = 6.06
KR downadj 2.10
06.6
510
Radj-down = 73.96 k
To trim up the output of a nominal 3.3V module
(QPW050A0F) to 3.6V
100
3.3 3.36.3
%
VVV
Data Sheet
February 2, 2011 QPW050/060 Series Power Modules; DC-DC converters
36-75Vdc Input; 1.2Vdc to 3.3Vdc Output
LINEAGE POWER 14
Feature Description (continued)
Output Voltage Set-Point Adjustment (Trim)
Δ% = 9.1
100
28 6.2928
%
VVV
Δ% = 5
KR upadj 936
5
1036
10
Rtadj-up = 11432 kΩ
KR upadj 2.10
1.9
510
1.9*225.1 1.9100*3.3*1.5
Rtadj-up = 98.47k
Output Over Voltage Protection
The output overvoltage protection consists of circuitry
that monitors the voltage on the output terminals. If
the voltage on the output terminals exceeds the over
voltage protection threshold, then the module will
shutdown and latch off. The overvoltage latch is reset
by either cycling the input power for one second or by
toggling the on/off signal for one second. The
protection mechanism is such that the unit can
continue in this condition until the fault is cleared.
Over Temperature Protection
These modules feature an overtemperature protection
circuit to safeguard against thermal damage. The
circuit shuts down and latches off the module when
the maximum device reference temperature is
exceeded. The module can be restarted by cycling
the dc input power for at least one second or by
toggling the remote on/off signal for at least one
second.
Input Under/Over Voltage Lockout
At input voltages below the input undervoltage lockout
limit, the module operation is disabled. The module
will begin to operate at an input voltage above the
undervoltage lockout turn-on threshold.
Data Sheet
February 2, 2011 QPW050/060 Series Power Modules; DC-DC converters
36-75Vdc Input; 1.2Vdc to 3.3Vdc Output
LINEAGE POWER 15
Thermal Considerations without
Baseplate
The power modules operate in a variety of thermal
environments; however, sufficient cooling should be
provided to help ensure reliable operation.
Considerations include ambient temperature, airflow,
module power dissipation, and the need for increased
reliability. A reduction in the operating temperature of
the module will result in an increase in reliability. The
thermal data presented here is based on physical
measurements taken in a wind tunnel.
Heat-dissipating components are mounted on the top
side of the module. Heat is removed by conduction,
convection and radiation to the surrounding
environment. Proper cooling can be verified by
measuring the thermal reference temperature (Tref ).
Peak temperature (Tref ) occurs at the position
indicated in Figures 38 - 40. For reliable operation this
temperature should not exceed listed temperature
threshold.
Figure 38. Tref Temperature Measurement
Location for Vo = 3.3V – 2.5V.
Figure 39. Tref Temperature Measurement
Location for Vo = 1.8V.
Figure 40. Tref Temperature Measu rement
Location for Vo = 1.5V – 1.2V
The output power of the module should not exceed
the rated power for the module as listed in the
Ordering Information table.
Although the maximum Tref temperature of the power
modules is 110 °C - 115 °C, you can limit this
temperature to a lower value for extremely high
reliability.
Heat Transfer via Convection
Increased airflow over the module enhances the heat
transfer via convection. Following derating figures
shows the maximum output current that can be
delivered by each module in the respective orientation
without exceeding the maximum Tref temperature
versus local ambient temperature (TA) for natural
convection through 2m/s (400 ft./min).
Note that the natural convection condition was
measured at 0.05 m/s to 0.1 m/s (10ft./min. to 20
ft./min.); however, systems in which these power
modules may be used typically generate natural
convection airflow rates of 0.3 m/s (60 ft./min.) due to
other heat dissipating components in the system. The
use of Figures 41 - 50 are shown in the following
example:
Example
What is the minimum airflow necessary for a
QPW050A0F operating at VI = 48 V, an output
current of 30A, and a maximum ambient temperature
of 70 °C in longitudinal orientation.
Solution:
Given: VI = 48V
Io = 30A
TA = 70 °C
Determine airflow (V) (Use Figure 41):
V = 1m/sec. (200ft./min.)
Tref =110ºC
Tref =115ºC
Tref = 115ºC
Data Sheet
February 2, 2011 QPW050/060 Series Power Modules; DC-DC converters
36-75Vdc Input; 1.2Vdc to 3.3Vdc Output
LINEAGE POWER 16
The following figures provide thermal derating characteristics.
OUTPUT CURRENT, IO (A)
0
5
10
15
20
25
30
35
40
45
50
25 30 35 40 45 50 55 60 65 70 75 80 85
NATURAL CONVECTION
1.0 m/s (200 ft./min.)
2.0 m/s (400 ft./min.)
OUTPUT CURRENT, IO (A)
0
10
20
30
40
50
60
25 30 35 40 45 50 55 60 65 70 75 80 85
NATURAL
CONVECTION
1.0 m/s (200 ft./min.)
2.0 m/s
(
400 ft./min.
)
LOCAL AMBIENT TEMPERATURE, TA (C) LOCAL AMBIENT TEMPERATURE, TA (C)
Figure 41. Output Power Derating for QPW050A0F (Vo
= 3.3V) in Lo ngitudinal Orientation with no baseplat e;
Airflow Direction From Vin(–) to Vout(--); Vin = 48V.
Figure 44. Output Power Derating for QPW060A0G (Vo
= 2.5V) in Transverse Orient ation with no baseplate;
Airflow Direction From Vin(–) to Vin(+); Vin = 48V.
OUTPUT CURRENT, IO (A)
0
10
20
30
40
50
25 30 35 40 45 50 55 60 65 70 75 80 8
5
NATURAL CONVECTION
1.0 m/s (200 ft./min.)
2.0 m/s (400 ft./min.)
OUTPUT CURRENT, IO (A)
0
10
20
30
40
50
60
25 30 35 40 45 50 55 60 65 70 75 80 85
NATURAL
CONVECTION
1.0 m/s
(
200 ft./min.
)
2.0 m/s (400 ft./min.)
LOCAL AMBIENT TEMPERATURE, TA (C) LOCAL AMBIENT TEMPERATURE, TA (C)
Figure 42. Output Power Derating for QPW050A0F (Vo
= 3.3V) in Transverse Orientation with no baseplate;
Airflow Direction From Vin(–) to Vin(+); Vin = 48V.
Figure 45. Output Power Derating for QPW060A0Y (Vo
= 1.8V) in Longitudinal Orientation w ith no baseplate;
Airflow Direction From Vin(–) to Vout(--); Vin = 48V.
OUTPUT CURRENT, IO (A)
0
10
20
30
40
50
60
25 30 35 40 45 50 55 60 65 70 75 80 85
NATURAL
CONVECTION
1.0 m/s (200 ft/min)
2.0 m/s (400 ft/min)
OUTPUT CURRENT, IO (A)
0
10
20
30
40
50
60
25 30 35 40 45 50 55 60 65 70 75 80 8
5
NATURAL
CONVECTION
1.0 m/s (200 ft./min.)
2.0 m/s (400 ft./min.)
LOCAL AMBIENT TEMPERATURE, TA (C) LOCAL AMBIENT TEMPERATURE, TA (C)
Figure 43. Output Power Derating for QPW060A0G (Vo
= 2.5V) in Lo ngitudinal Orientation with no baseplat e;
Airflow Direction From Vin(–) to Vout(--); Vin = 48V.
Figure 46. Output Power Derating for QPW060A0Y (Vo
= 1.8V) in Transverse Orient ation with no baseplate;
Airflow Direction From Vin(–) to Vin(+); Vin = 48V.
Data Sheet
February 2, 2011 QPW050/060 Series Power Modules; DC-DC converters
36-75Vdc Input; 1.2Vdc to 3.3Vdc Output
LINEAGE POWER 17
The following figures provide thermal derating characteristics.
OUTPUT CURRENT, IO (A)
0
10
20
30
40
50
60
25 30 35 40 45 50 55 60 65 70 75 80 85
NATURAL
CONVECTION
1.0 m/s (200 ft./min.)
2.0 m/s (400 ft./min.)
OUTPUT CURRENT, IO (A)
0
10
20
30
40
50
60
25 30 35 40 45 50 55 60 65 70 75 80 85
NATURAL CONVECTION
1.0 m/s (200 ft./min.)
2.0 m/s (400 ft./min.)
LOCAL AMBIENT TEMPERATURE, TA (C) LOCAL AMBIENT TEMPERATURE, TA (C)
Figure 47. Output Power Derating for QPW060A0M (Vo
= 1.5V) in Lo ngitudinal Orientation with no baseplat e;
Airflow Direction From Vin(–) to Vout(--); Vin = 48V.
Figure 50. Output Power Derating for QPW060A0P (Vo
= 1.2V) in Transverse Orient ation with no baseplate;
Airflow Direction From Vin(–) to Vin(+); Vin = 48V.
OUTPUT CURRENT, IO (A)
0
10
20
30
40
50
60
25 30 35 40 45 50 55 60 65 70 75 80 85
NATURAL CONVECTION
1.0 m/s (200 ft./min.)
2.0 m/s (400 ft./min.)
Please refer to the Application Note “Thermal
Characterization Process For Open-Frame Board-Mounted
Power Modules” for a detailed discussion of thermal
aspects including maximum device temperatures.
LOCAL AMBIENT TEMPERATURE, TA (C)
Figure 48. Output Power Derating for QPW060A0M (Vo
= 1.5V) in Transverse Orientation with no baseplate;
Airflow Direction From Vin(–) to Vin(+); Vin = 48V.
OUTPUT CURRENT, IO (A)
0
10
20
30
40
50
60
25 30 35 40 45 50 55 60 65 70 75 80 85
NATURAL CONVECTION
1.0 m/s (200 ft./min.)
2.0 m/s (400 ft./min.)
LOCAL AMBIENT TEMPERATURE, TA (C)
Figure 49. Output Power Derating for QPW060A0P (Vo
= 1.2V) in Lo ngitudinal Orientation with no baseplat e;
Airflow Direction From Vin(–) to Vout(--); Vin = 48V.
Data Sheet
February 2, 2011 QPW050/060 Series Power Modules; DC-DC converters
36-75Vdc Input; 1.2Vdc to 3.3Vdc Output
LINEAGE POWER 18
Thermal Considerations with
Baseplate
The baseplate option (-H) power modules are
constructed with baseplate on topside of the open
frame power module. The baseplate includes quarter
brick through-threaded, M3 x 0.5 mounting hole
pattern, which enable heat sinks or cold plates to
attaché to the module. The mounting torque must not
exceed 0.56 N-m (5 in.-lb.) during heat sink assembly.
This module operates in a variety of thermal
environments; however, sufficient cooling should be
provided to help ensure reliable operation.
Considerations include ambient temperature, airflow,
module power dissipation, and the need for increased
reliability. A reduction in the operating temperature of
the module will result in an increase in reliability. The
thermal data presented here is based on physical
measurements taken in a wind tunnel.
Heat-dissipating components are mounted on the
topside of the module and coupled to the baseplate
with thermal gap material. Heat is removed by
conduction, convection and radiation to the
surrounding environment. Proper cooling can be
verified by measuring the thermal reference
temperature (Tref ). Peak temperature (Tref ) occurs at
the position indicated in Figure 51. For reliable
operation this temperature should not exceed 95ºC
temperature threshold.
Figure 51. Tref Temperature Measurement
Location for QPW-H baseplate option
The output power of the module should not exceed
the rated power for the module as listed in the
Ordering Information table.
Although the maximum Tref temperature of the power
modules is 95 °C, you can limit this temperature to a
lower value for extremely high reliability. Please refer
to the Application Note “Thermal Characterization
Process For Open-Frame Board-Mounted Power
Modules” for a detailed discussion of thermal aspects
including maximum device temperatures.
Heat Transfer via Convection
Increased airflow over the module enhances the heat
transfer via convection. Following derating figures
shows the maximum output current that can be
delivered by each module in the respective orientation
without exceeding the maximum Tref temperature
versus local ambient temperature (TA) for natural
convection through 2m/s (400 ft./min).
Note that the natural convection condition was
measured at 0.05 m/s to 0.1 m/s (10ft./min. to 20
ft./min.); however, systems in which these power
modules may be used typically generate natural
convection airflow rates of 0.3 m/s (60 ft./min.) due to
other heat dissipating components in the system. The
use of Figures 2 - 4 are shown in the following
example:
Example
What is the minimum airflow and heat sink size
necessary for a QPW050A0F-H operating at VI = 48
V, an output current of 30A, and a maximum ambient
temperature of 70 °C in transverse orientation.
Solution:
Given: VI = 48V
Io = 30A
TA = 70 °C
To determine airflow (V) and heatsink size (Use
Figures 52 - 53):
There are couple of solution can be derived from
below derating figures.
1) Baseplated with 0.25” heatsink in natural
convection (V= 0 m/sec) environment.
2) No baseplate required when operated with
airflow of 200 LFM (V = 1m/sec).
Tref
Data Sheet
February 2, 2011 QPW050/060 Series Power Modules; DC-DC converters
36-75Vdc Input; 1.2Vdc to 3.3Vdc Output
LINEAGE POWER 19
The following figures provide thermal derating
characteristics.
OUTPUT CURRENT, IO (A)
LOCAL AMBIENT TEMPERATURE, TA (C)
Figure 52. Output Power Derating for QPW050A0F
(Vo = 3.3V) in Transverse Orientation with baseplate
in natural convection environment; Airflow Direction
From Vin (–) to Vi n (+) ; Vin = 48V
OUTPUT CURRENT, IO (A)
LOCAL AMBIENT TEMPERATURE, TA (C)
Figure 53. Output Power Derating for QPW050A0F
(Vo = 3.3V) in Transverse Orientation with baseplate
in 200 LFM airflow environment; Airflow Direction
From Vin (–) to Vi n (+) ; Vin = 48V
OUTPUT CURRENT, IO (A)
LOCAL AMBIENT TEMPERATURE, TA (C)
Figure 54. Output Power Derating for QPW050A0F
(Vo = 3.3V) in Transverse Orientation with baseplate
in 400 LFM airflow environment; Airflow Direction
From Vin (–) to Vi n (+) ; Vin = 48V
0
5
10
15
20
25
30
35
40
45
50
55
25 30 35 40 45 50 55 60 65 70 75 80 85
Open frame
Baseplate
Baseplate w/ 0.25" heat sink
Baseplate w/ 0.5" heat sink
0
5
10
15
20
25
30
35
40
45
50
55
25 30 35 40 45 50 55 60 65 70 75 80 85
Open frame
Baseplate
Baseplate w/ 0.25" heat sink
Baseplate w/ 0.5" heat sink
0
5
10
15
20
25
30
35
40
45
50
55
25 30 35 40 45 50 55 60 65 70 75 80 85
Open frame
Baseplate
Baseplate w/ 0.25" heat sink
Baseplate w/ 0.5" heat sink
Data Sheet
February 2, 2011 QPW050/060 Series Power Modules; DC-DC converters
36-75Vdc Input; 1.2Vdc to 3.3Vdc Output
LINEAGE POWER 20
Layout Considerations
The QPW power module series are low profile in
order to be used in fine pitch system card
architectures. As such, component clearance
between the bottom of the power module and the
mounting board is limited. Avoid placing copper areas
on the outer layer directly underneath the power
module. Also avoid placing via interconnects
underneath the power module.
For additional layout guide-lines, refer to
FLTR100V10 data sheet.
Post solder Cleaning and Drying
Considerations
Post solder cleaning is usually the final circuit-board
assembly process prior to electrical board testing. The
result of inadequate cleaning and drying can affect
both the reliability of a power module and the
testability of the finished circuit-board assembly. For
guidance on appropriate soldering, cleaning and
drying procedures, refer to Lineage Power Board
Mounted Power Modules: Soldering and Cleaning
Application Note.
Through-Hole Lead-Free Soldering
Information
The RoHS-compliant through-hole products use the
SAC (Sn/Ag/Cu) Pb-free solder and RoHS-compliant
components. They are designed to be processed
through single or dual wave soldering machines. The
pins have an RoHS-compliant finish that is compatible
with both Pb and Pb-free wave soldering processes.
A maximum preheat rate of 3C/s is suggested. The
wave preheat process should be such that the
temperature of the power module board is kept below
210C. For Pb solder, the recommended pot
temperature is 260C, while the Pb-free solder pot is
270C max. Not all RoHS-compliant through-hole
products can be processed with paste-through-hole
Pb or Pb-free reflow process. If additional information
is needed, please consult with your Lineage Power
representative for more details.
Data Sheet
February 2, 2011 QPW050/060 Series Power Modules; DC-DC converters
36-75Vdc Input; 1.2Vdc to 3.3Vdc Output
LINEAGE POWER 21
Mechanical Outline for Thro ugh-Hole Module without Baseplate Op tion
Dimensions are in millimeters and [inches].
Tolerances: x.x mm 0.5 mm [x.xx in. 0.02 in.] (Unless otherwise indicated)
x.xx mm 0.25 mm [x.xxx in 0.010 in.]
TOP
VIEW
SIDE
VIEW
BOTTOM
VIEW
*Top side label includes Lineage Power name, product designation, and data code.
Data Sheet
February 2, 2011 QPW050/060 Series Power Modules; DC-DC converters
36-75Vdc Input; 1.2Vdc to 3.3Vdc Output
LINEAGE POWER 22
Mechanical Outline for Through-Hole Module with Baseplate Option
Dimensions are in millimeters and [inches].
Tolerances: x.x mm 0.5 mm [x.xx in. 0.02 in.] (Unless otherwise indicated)
x.xx mm 0.25 mm [x.xxx in 0.010 in.]
TOP
VIEW
SIDE
VIEW
BOTTOM
VIEW
*Bottom side label includes Lineage Power name, product designation, and data code.
Data Sheet
February 2, 2011 QPW050/060 Series Power Modules; DC-DC converters
36-75Vdc Input; 1.2Vdc to 3.3Vdc Output
LINEAGE POWER 23
Recommended Pad Layout for Through Hole Module
Dimensions are in millimeters and (inches).
Tolerances: x.x mm 0.5 mm (x.xx in. 0.02 in.) [unless otherwise indicated]
x.xx mm 0.25 mm (x.xxx in 0.010 in.)
† - Option Feature, Pin is not present unless one of these options specified.
Data Sheet
February 2, 2011 QPW050/060 Series Power Modules; DC-DC converters
36-75Vdc Input; 1.2Vdc to 3.3Vdc Output
Document No: DS03-075 ver 1.16
PDF name: QPW Series.pdf
Ordering Information
Please contact your Lineage Power Sales Representative for pricing, availability and optional features.
Table 1. Device Code
Product codes Input Voltage Output
Voltage Output
Current Efficiency Connector
Type Comcodes
QPW050A0F1 48V (36-75Vdc) 3.3V 50A 93% Through hole 108968686
QPW050A0F1Z 48V (36-75Vdc) 3.3V 50A 93% Through hole CC109113940
QPW050A0F41 48V (36-75Vdc) 3.3V 50A 93% Through hole 108986498
QPW050A0F41Z 48V (36-75Vdc) 3.3V 50A 93% Through hole CC109107190
QPW050A0F641Z 48V (36-75Vdc) 3.3V 50A 93% Through hole CC109163655
QPW050A0F1-HZ 48V (36-75Vdc) 3.3V 50A 93% Through hole CC109107182
QPW050A0F71-H 48V (36-75Vdc) 3.3V 50A 93% Through hole 108987207
QPW050A0F71-HZ 48V (36-75Vdc) 3.3V 50A 93% Through hole CC109107208
QPW050A0F41-HZ 48V (36-75Vdc) 3.3V 50A 93% Through hole CC109138483
QPW050A0F641-HZ 48V (36-75Vdc) 3.3V 50A 93% Through hole CC109135101
QPW060A0G1 48V (36-75Vdc) 2.5V 60A 91% Through hole 108982232
QPW060A0G1Z 48V (36-75Vdc) 2.5V 60A 91% Through hole CC109107216
QPW060A0G71-H 48V (36-75Vdc) 2.5V 60A 91% Through hole 108987215
QPW060A0G71-HZ 48V (36-75Vdc) 2.5V 60A 91% Through hole CC109107224
QPW060A0Y1 48V (36-75Vdc) 1.8V 60A 89% Through hole 108982265
QPW060A0M1 48V (36-75Vdc) 1.5V 60A 87% Through hole 108982240
QPW060A0M1Z 48V (36-75Vdc) 1.5V 60A 87% Through hole CC109114468
QPW060A0M1-HZ 48V (36-75Vdc) 1.5V 60A 87% Through hole CC109148846
QPW060A0P1 48V (36-75Vdc) 1.2V 60A 85% Through hole 108982257
QPW060A0P1Z 48V (36-75Vdc) 1.2V 60A 85% Through hole CC109113957
QPW060A0P41 48V (36-75Vdc) 1.2V 60A 85% Through hole CC109110533
QPW060A0P641 48V (36-75Vdc) 1.2V 60A 85% Through hole 108982380
QPW060A0P1-H 48V (36-75Vdc) 1.2V 60A 85% Through hole 108986506
Table 2. Device Options Option Suffix
Negative remote on/off logic 1
Auto-restart 4
Pin Length: 3.68 mm ± 0.25mm (0.145 in. ± 0.010 in.) 6
Case Pin (only available with –H option) 7
Base Plate option -H
RoHS Compliant -Z
Wor l d Wide Headquart ers
Lineage Power Corporation
601 Shiloh Road, Plano, TX 75074, USA
+1-888-LINEAGE(546-3243)
(Outside U.S.A.: +1-972-244-WATT(9288))
www.lineagepower.com
e-mail: techsupport1@lineagepower.com
Asia-Pacific Headquarters
Tel: +86.021.54279977*808
Europe, Middl e-East and Africa Headquarters
Tel: +49.89.878067-280
India Headquarters
Tel: +91.80.28411633
Lineage Power reserves the right to make changes to the product(s) or information contained herein without notice. No liability is assumed as a result of their use or
a
pplication. No rights under any patent accompany the sale of any such product(s) or information.
Lineage Power DC-DC products are protected under various patents. Information on these patents is available at www.lineagepower.com/patents.
©
2010 Lineage Power Corporation, (Plano, Texas) All International Rights Reserved.
