Embedded Power for Business-Critical Continuity Rev.3.4.09_96 SIL10E_05 Series 1 of 4 SIL10E Series 3.0 Vin - 5.5 Vin Total Power: 49.9 Watts Input Voltage: 3.0-5.5 Vdc # of Outputs: Single Electrical Specifications Special Features * * * * * * * * 10 A Current rating Input voltage range: 3 Vdc to 5.5 Vdc Output voltage range: 0.8 Vdc to 3.63 Vdc Ultra high efficiency: 96% @ 5 Vin and 3.3 Vout Extremely low internal power dissipation Minimal thermal design concerns Designed in reliability: MTBF of 7,000,000 hours per Telcordia SR-332 Ideal solution where board space is at a premium or tighter card pitch is required Industry standard footprint and pin out Available RoHScompliant 2 year warranty Input Input voltage range: Input current: 3.0-5.5 Vdc No load 70 mA Input current (max.): 8 A max. @ lo max. and Vout = 3.3 V Input reflected ripple: 65 mA rms Remote ON/OFF: (See Note 2) Start-up time: 20 ms Output Voltage adjustability: (See Note 1) Fixed output versions 5 Vin with wide trim 3.3 Vin with wide trim 10% 0.8 - 3.63 Vdc 0.8 - 2.75 Vdc Setpoint accuracy: 0.4% typ. Line regulation: 0.2% typ. Load regulation: 1.0% typ. Minimum load: 0A Overshoot/Undershoot: None Ripple and noise: 50 mV pk-pk 25 mV rms max. * UL/cUL CAN/CSA 22.2 No. 60950-1-03/UL 60950-1, File No. E186249 Temperature co-efficient: 0.01%/C Transient response: 50 mV max. deviation 50s recovery to within 1.0% * TUV Product Service (EN60950) Certificate No. B 08 05 51485 378 Remote sense: 10% Vo compensation * * * Safety * CBreport and certificate to IEC60950, Certificate No. DE3-51686M1 All specifications are typical at nominal input, full load at 25 C unless otherwise stated. Embedded Power for Business-Critical Continuity Rev.3.4.09_96 SIL10E_05 Series 2 of 4 EMC Characteristics Electrostatic discharge: EN61000-4-2, IEC801-2 Conducted immunity: EN61000-4-6 Radiated immunity: EN61000-4-3 General Specifications Efficiency: See table Insulation voltage: Switching frequency: Non-isolated Fixed Approvals and standards: 300 kHz typ. EN60950 UL/cUL60950 Material flammability: UL94V-0 Dimensions (L x W x H) 50.8 x 7.8 x 12.7 mm 2.0 x 0.31 x 0.5 inches Pin length: (Vertical) 0.135 0.02 in (3.43 0.5 mm) Weight: MTBF: 5 g (0.18 oz) Telcordia SR-332 MIL-HDBK-217F 7,042,000 hours 680,000 hours Environmental Specifications Thermal performance: (See Note 3) Operating ambient temperature -40 C to +100 C Non-operating -40 C to +125 C Protection Short circuit: Continuous Thermal: Automatic recovery Embedded Power for Business-Critical Continuity Rev.3.4.09_96 SIL10E_05 Series 3 of 4 Ordering Information All specifications are typical at nominal input, full load at 25 C unless otherwise stated. Ordering Information Output Power (Max.) Input Voltage Output Voltage 8.8 W 3.0 - 5.5 Vdc Output Currents Regulation Min Max Efficiency (typ.) 0.8 V 0A 10 A 83% 0.2% 1.5% SIL10E-05S0V8-VJ (EOL) Line Load Model Numbers (4, 5, 6) 11 W 3.0 - 5.5 Vdc 1V 0A 10 A 86% 0.2% 1.5% SIL10E-05S1V0-VJ (EOL) 13.2 W 3.0 - 5.5 Vdc 1.2 V 0A 10 A 88% 0.2% 1.0% SIL10E-05S1V2-VJ (EOL) 16.5 W 3.0 - 5.5 Vdc 1.5 V 0A 10 A 90% 0.2% 1.0% SIL10E-05S1V5-VJ (EOL) 19.8 W 3.0 - 5.5 Vdc 1.8 V 0A 10 A 92% 0.2% 1.0% SIL10E-05S1V8-VJ (EOL) 22 W 3.0 - 5.5 Vdc 2V 0A 10 A 93% 0.2% 1.0% SIL10E-05S2V0-VJ (EOL) 27.5 W 3.0 - 5.5 Vdc 2.5 V 0A 10 A 94% 0.2% 1.0% SIL10E-05S2V5-VJ (EOL) 36.3 W 4.5 - 5.5 Vdc 3.3 V 0A 10 A 95% 0.2% 1.0% SIL10E-05S3V3-VJ (EOL) 36.3 W 4.5 - 5.5 Vdc 0.8 - 3.63 V 0A 10 A 95% 0.2% 1.0% SIL10E-05W3V3-VJ Part Number System with Options SIL10E-05S3V3-VJ Product Family SIL = Single In Line Rated Output Current 10 = 10 Amps Performance E= Enhanced Performance Input Voltage 05 = 3.0 V to 5.5 V 12 = 10 V to 14 V Packaging Options (5) J = Pb-free RoHS 6/6 compliant Mounting Options V = Vertical Mount H = Horizontal Mount Output Voltage 2.5 V, 3.3 V, etc Number of Outputs S = Single W = Wide Output Voltage Adjustment of the SIL10E-05W3V3J Series The ultra-wide output voltage trim range offers major advantages to users who select the SIL10E-05W3V3J. It is no longer necessary to purchase a variety of modules in order to cover different output voltages. The output voltage can be trimmed in a range of 0.8 Vdc to 3.63 Vdc. When the SIL10E-05W3V3J converter leaves the factory the output has been adjusted to the default voltage of 3.3 V. *When Vin 4.5 V, then Vout can be adjusted from 0.8 Vdc to 3.6 Vdc *When Vin < 4.5 V, then Vout can be adjusted from 0.8 Vdc to 2.75 Vdc Notes Notes Continued 1 When Vin 4.5 V, then Vout can be adjusted from 0.8 V to 3.6 V. When Vin < 4.5 V, then Vout can be adjusted from 0.8 V to 2.75 V. 2 The SIL10E features a `Negative Logic' Remote ON/OFF operation. If you are not using the Remote ON/OFF pin, leave the pin open (the converter will be on). The Remote ON/OFF pin is referenced to ground. The following conditions apply for the SIL10E: 3 Full derating curves available in both the Longform Datasheet and Application Note 136. 4 For certain applications that use low ESR capacitors on the output of the convertor and to insure maximum converter stability, please add the suffix `02' to the model, e.g. SIL10E-05S2V5-V02J. 5 TSE RoHS 5/6 (non Pb-free) compliantversions may be available on special request, please contact your local sales representative for details. 6 NOTICE: Some models do not support all options. Please contact your local Emerson Network Power representative or use the on-line model number search tool at http://www.PowerConversion.com to find a suitable alternative. ConfigurationConverter Operation Remote pin open circuit Unit is ON Remote pin pulled low Unit is ON Remote pin pulled high [Von/off >1.2 V] Unit is OFF Embedded Power for Business-Critical Continuity Americas Mechanical Drawings PIN VIEW 2.000 0.020 (50.80 0.50) 0.316 0.008 (8.03 0.20) 0.170 (4.32) 0.500 (12.70) PCB 5810 Van Allen Way Carlsbad, CA 92008 USA Telephone:+1 760 930 4600 Facsimile: +1 760 930 0698 Europe (UK) 6 0.025 0.001 (0.64 0.02) SIDE VIEW Rev.3.4.09_96 SIL10E_05 Series 4 of 4 5 3 2 5 1 J2 4 3 Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom Telephone:+44 (0) 1384 842 211 Facsimile: +44 (0) 1384 843 355 1 2 J1 0.100 (2.54) 1.900 (48.26) Asia (HK) 0.050 (1.27) Dimensions in Inches (mm) Tolerances (unless otherwise specified) 2 Place 0.15 3 Place 0.006 Figure 1: Horizontal Mount Version 14/F, Lu Plaza 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong Telephone:+852 2176 3333 Facsimile: +852 2176 3888 For global contact, visit: www.PowerConversion.com SIDE VIEW techsupport.embeddedpower @emerson.com FRONT VIEW 2.000 0.020 (50.80 0.50) 0.307 0.008 (7.80 0.20) 0.500 (12.70) PCB 0.135 (3.43) 0.635 (16.13) 1 2 3 4 1 5 0.025 0.001 (0.64 0.02) J1 0.168 (4.26) 2 3 J2 5 6 Emerson Network Power. The global leader in enabling business-critical continuity. AC Power 0.100 (2.54) 0.050 (1.27) While every precaution has been taken to ensure accuracy and completeness in this literature, Emerson Network Power assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Connectivity 1.900 (48.26) DC Power Dimensions in Inches (mm) Tolerances (unless otherwise specified) 2 Place 0.15 3 Place 0.006 Figure 2: Vertical Mount Version Input Pin Connections Embedded Power Monitoring Input Pin Connections J1 Embedded Computing J2 Outside Plant Power Switching & Controls Pin 2 +Vout Pin 2 +Vin Precision Cooling Racks & Integrated Cabinets Pin 3 Remote Sense (+) Pin 3 +Vin Services Pin 4 +Vout Pin 4 No Pin Pin 5 Ground Pin 5 Trim Pin 6 Remote ON/OFF Pin 1 +Vout Pin 1 Ground Surge Protection EmersonNetworkPower.com Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co. (c)2008 Emerson Electric Co.