Data Sheet September 10, 2013 Austin MegaLynxTM SMT: Non-Isolated DC-DC Power Modules: 2.7Vdc - 4.0Vdc input; 0.8 to 2.0Vdc; 30A Output Current RoHS Compliant Features Compliant to RoHS EU Directive 2002/95/EC Compatible in a Pb-free or SnPb reflow environment Delivers up to 30A of output current Input voltage range from 2.7V to 4.0Vdc High efficiency - 92% @ 1.8V full load (VIN=3.3Vdc) Output voltage programmable from 0.8 to 2.0Vdc Small size and low profile: o 33.0 mm x 9.1 mm x 13.5 mm o (1.30 in. x 0.36 in. x 0.53 in.) Applications Distributed power architectures Intermediate bus voltage applications Telecommunications equipment Servers and storage applications Networking equipment Monotonic start-up into pre-biased output Output voltage sequencing (EZ-SEQUENCE TM ) Remote On/Off Remote Sense Over current and Over temperature protection Parallel operation with active current sharing Wide operating temperature range (-40C to 85C) UL* 60950 Recognized, CSA C22.2 No. 60950-00 rd Certified, and VDE 0805 (EN60950-1 3 edition) Licensed ISO** 9001 and ISO 14001 certified manufacturing facilities Description The Austin MegaLynx ATM series SMT power modules are non-isolated DC-DC converters in an industry standard package that can deliver up to 30A of output current with a full load efficiency of 92% at 1.8Vdc output voltage (VIN = 3.3Vdc). These modules operate off an input voltage from 2.7 to 4.0Vdc and provide an output voltage that is programmable from 0.8 to 2.0Vdc. They have a sequencing feature that enables designers to implement various types of output voltage sequencing when powering multiple modules on the board. Additional features include remote On/Off, adjustable output voltage, remote sense, over current, over temperature protection and active current sharing between modules. * UL is a registered trademark of Underwriters Laboratories, Inc. CSA is a registered trademark of Canadian Standards Association. VDE is a trademark of Verband Deutscher Elektrotechniker e.V. ** ISO is a registered trademark of the International Organization of Standards Document No: DS06-130 ver. 1.08 PDF No: ATM030A0X3-SR_ds.pdf Data Sheet September 10, 2013 Austin MegaLynxTM SMT: Non-Isolated DC-DC Power Modules: 2.7 - 4.0Vdc input; 0.8 to 2.0Vdc Output; 30A output current Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability. Parameter Device Symbol Min Max Unit Input Voltage All VIN -0.3 4.0 Vdc Sequencing pin voltage Continuous All VsEQ -0.3 4.0 Vdc Operating Ambient Temperature All TA -40 85 C All Tstg -55 125 C (see Thermal Considerations section) Storage Temperature Electrical Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Parameter Device Symbol Min Typ Max Unit Operating Input Voltage All VIN 2.7 3.3 4.0 Vdc Maximum Input Current (VIN= VIN,min , VO= VO,set, IO=IO, max) All IIN,max 20 Adc Inrush Transient All 2 1 A s Input Reflected Ripple Current, peak-to-peak (5Hz to 20MHz, 1H source impedance; VIN=2.7V to 4.0V, IO= IOmax ; See Figure 1) All 100 mAp-p Input Ripple Rejection (120Hz) All 50 dB LINEAGE POWER I t 2 2 Data Sheet September 10, 2013 Austin MegaLynxTM SMT: Non-Isolated DC-DC Power Modules: 2.7 - 4.0Vdc input; 0.8 to 2.0Vdc Output; 30A output current Electrical Specifications (continued) Parameter Output Voltage Set-point Device Symbol Min Typ Max Unit All VO, set -1.5 +1.5 % VO, set All VO, set -3.0 +3.0 % VO, set 2.0 Vdc (VIN=VIN,nom, IO=IO, nom, Tref=25C) Output Voltage (Over all operating input voltage, resistive load, and temperature conditions until end of life) Adjustment Range Selected by an external resistor All 0.8 Output Regulation Line (VIN=VIN, min to VIN, max) All 0.1 % VO, set Load (IO=IO, min to IO, max) All 0.4 % VO, set Temperature (Tref=TA, min to TA, max) All 0.5 1 % VO, set Vo 2.0V 50 mVpk-pk F Output Ripple and Noise on nominal output (VIN=VIN, nom and IO=IO, min to IO, max COUT = 0.1F // 10 F ceramic capacitors) Peak-to-Peak (5Hz to 20MHz bandwidth) External Capacitance 1 ESR 1 m All CO, max 0 2,000 ESR 10 m All CO, max 0 10,000 F Vo 3.63V Io 0 30 Adc Output Current Output Current Limit Inception (Hiccup Mode) All IO, lim 104 140 160 % Iomax Output Short-Circuit Current All IO, s/c 3.5 Adc VO,set = 0.8dc 83.5 % VIN=VIN, nom, TA=25C VO,set = 1.25Vdc 87.9 % IO=IO, max , VO= VO,set VO,set = 1.8Vdc 91.6 All fsw 270 kHz (dIO/dt=5A/s; VIN=VIN, nom; TA=25C) Load Change from Io= 50% to 100% of IO,max; No external output capacitors Peak Deviation All Vpk 380 mV Settling Time (VO<10% peak deviation) All ts 50 s (dIO/dt=5A/s; VIN=VIN, nom; TA=25C) Load Change from IO= 100% to 50%of IO, max: No external output capacitors Peak Deviation All Vpk 380 mV Settling Time (VO<10% peak deviation) All ts 50 s (VO250mV) ( Hiccup Mode ) Efficiency Switching Frequency, Fixed % Dynamic Load Response 1 Note that maximum external capacitance may be lower when sequencing is employed. Please check with your Lineage Power Technical representative. LINEAGE POWER 3 Data Sheet September 10, 2013 Austin MegaLynxTM SMT: Non-Isolated DC-DC Power Modules: 2.7 - 4.0Vdc input; 0.8 to 2.0Vdc Output; 30A output current Electrical Specifications (continued) Parameter Device Symbol Min Typ Max Unit (dIO/dt=5A/s; VIN=VIN, nom; TA=25C) Load Change from Io= 50% to 100% of Io,max; 2x150 F polymer capacitor Peak Deviation All Vpk 350 mV Settling Time (VO<10% peak deviation) All ts 40 s (dIO/dt=5A/s; VIN=VIN, nom; TA=25C) Load Change from Io= 100% to 50%of IO,max: 2x150 F polymer capacitor Peak Deviation All Vpk 250 mV Settling Time (VO<10% peak deviation) All ts 60 s Dynamic Load Response General Specifications Parameter Min Calculated MTBF (VO= 1.2Vdc, IO= 0.8IO, max, TA=40C) Per Telecordia Method Weight LINEAGE POWER Typ Max Hours 3,443,380 6.2 (0.22) Unit g (oz.) 4 Austin MegaLynxTM SMT: Non-Isolated DC-DC Power Modules: 2.7 - 4.0Vdc input; 0.8 to 2.0Vdc Output; 30A output current Data Sheet September 10, 2013 Feature Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. See Feature Descriptions for additional information. Parameter Device Symbol Min Typ Max Unit Input High Current All IIH 0.5 3.3 mA Input High Voltage All VIH 2.5 VIN, max V Input Low Current All IIL 200 A Input Low Voltage All VIL -0.3 1.2 V All Tdelay 3.8 4.7 6 msec All Tdelay 3.8 4.7 6 msec All Trise 2.5 3 3.8 msec 3.0 % VO, set On/Off Signal Interface (VIN=VIN, min to VIN, max ; open collector or equivalent, Signal referenced to GND) Logic High (Module OFF) Logic Low (Module ON) Turn-On Delay and Rise Times (VIN=VIN, nom, IO=IO, max , VO to within 1% of steady state) Case 1: On/Off input is enabled and then input power is applied (delay from instant at which VIN = VIN, min until Vo = 10% of Vo, set) Case 2: Input power is applied for at least one second and then the On/Off input is enabled (delay from instant at which Von/Off is enabled until Vo = 10% of Vo, set) Output voltage Rise time (time for Vo to rise from 10% of Vo, set to 90% of Vo, set) Output voltage overshoot o IO = IO, max; VIN, min - VIN, max, TA = 25 C 0.5 V 125 C -- 2 V/msec Remote Sense Range All Over temperature Protection All Tref All dVSEQ/dt to application of voltage on SEQ pin) All TsEQ-delay Tracking Accuracy All VSEQ -Vo 100 200 mV VSEQ -Vo 200 400 mV 2.2 Vdc (See Thermal Consideration section) Sequencing Slew rate capability (VIN, min to VIN, max; IO, min to IO, max VSEQ < Vo) Sequencing Delay time (Delay from VIN, min Power-up (2V/ms) Power-down (1V/ms) 10 msec (VIN, min to VIN, max; IO, min - IO, max VSEQ < Vo) Input Undervoltage Lockout Turn-on Threshold All Turn-off Threshold All Forced Load Share Accuracy -P Number of units in Parallel -P LINEAGE POWER 1.7 Vdc 10 % Io 5 5 Austin MegaLynxTM SMT: Non-Isolated DC-DC Power Modules: 2.7 - 4.0Vdc input; 0.8 to 2.0Vdc Output; 30A output current Data Sheet September 10, 2013 Characteristic Curves The following figures provide typical characteristics for the ATM030A0X3-SR & -SRH (0.8V, 30A) at 25oC. 95 35 Vin = 3.0V 85 Vin = 3.3V OUTPUT CURRENT, Io (A) EFFICIENCY, (%) 90 Vin = 3.9V 80 75 70 65 0 5 10 15 20 25 2.5m/s 500 LFM 30 25 1m/s 200 LFM 1.5m/s 300 LFM 15 2.0m/s 400 LFM 10 5 0 30 30 40 50 60 70 80 O OUTPUT CURRENT, IO (A) Figure 1. Converter Efficiency versus Output Current. 0.5m/s 100 LFM NC 20 AMBIENT TEMPERATURE, TA C Figure 4. Derating Output Current versus Ambient Temperature and Airflow (ATM030A0X3-SR). 35 OUTPUT CURRENT, Io (A) VO (V) (20mV/div) OUTPUT VOLTAGE 2.5m/s (500LFM) 30 NC 0.5m/s (100LFM) 25 1m/s (200LFM) 1.5m/s (300LFM) 20 2m/s (400LFM) 15 30 LINEAGE POWER OUTPUT VOLTAGE VO (V) (1V/div) OUTPUT VOLTAGE Figure 3. Transient Response to Dynamic Load Change from 0% to 50% to 0% of full load. 60 70 80 Figure 5. Derating Output Current versus Ambient Temperature and Airflow (ATM030A0X3-SRH). VIN (V) (1V/div) TIME, t (50s /div) 50 O INPUT VOLTAGE IO (A) (5Adiv) OUTPUT CURRENT, VO (V) (200mV/div) Figure 2. Typical output ripple and noise (VIN = VIN,NOM, Io = Io,max). 40 AMBIENT TEMPERATURE, TA C TIME, t (1s/div) TIME, t (5ms/div) Figure 6. Typical Start-up Using Input Voltage (VIN = VIN,NOM, Io = Io,max). 6 Austin MegaLynxTM SMT: Non-Isolated DC-DC Power Modules: 2.7 - 4.0Vdc input; 0.8 to 2.0Vdc Output; 30A output current Data Sheet September 10, 2013 Characteristic Curves The following figures provide typical characteristics for the ATM030A0X3-SR and -SRH (1.25V, 30A) at 25oC. 95 35 Vin = 3.0V OUTPUT CURRENT, Io (A) Vin = 3.3V EFFICIENCY, (%) 2.5m/s 500 LFM 30 90 Vin = 3.9V 85 80 75 70 65 0 5 10 15 20 25 30 25 1m/s 200 LFM 1.5m/s 300 LFM 15 2.0m/s 400 LFM 10 5 0 30 40 50 60 70 80 O AMBIENT TEMPERATURE, TA C OUTPUT CURRENT, IO (A) Figure 7. Converter Efficiency versus Output Current. 0.5m/s 100 LFM NC 20 Figure 10. Derating Output Current versus Ambient Temperature and Airflow (ATM030A0X3-SR). 35 OUTPUT CURRENT, Io (A) VO (V) (20mV/div) OUTPUT VOLTAGE 2.5m/s (500LFM) 2m/s (400LFM) 30 NC 0.5m/s (100LFM) 25 1m/s (200LFM) 1.5m/s (300LFM) 20 30 Figure 9. Transient Response to Dynamic Load Change from 0% to 50% to 0% of full load. LINEAGE POWER 60 70 80 AMBIENT TEMPERATURE, TA C OUTPUT VOLTAGE VO (V) (1V/div) VIN (V) (1V/div) Figure 11. Derating Output Current versus Ambient Temperature and Airflow (ATM030A0X3-SRH). INPUT VOLTAGE OUTPUT VOLTAGE VO (V) (200mV/div) IO (A) (5Adiv) OUTPUT CURRENT, TIME, t (50s /div) 50 O TIME, t (1s/div) Figure 8. Typical output ripple and noise (VIN = VIN,NOM, Io = Io,max). 40 TIME, t (5ms/div) Figure 12. Typical Start-up Using Input Voltage (VIN = VIN,NOM, Io = Io,max). 7 Austin MegaLynxTM SMT: Non-Isolated DC-DC Power Modules: 2.7 - 4.0Vdc input; 0.8 to 2.0Vdc Output; 30A output current Data Sheet September 10, 2013 Characteristic Curves The following figures provide typical characteristics for the ATM030A0X3-SR and -SRH (1.8V, 30A) at 25oC. 35 100 Vin = 3.0V Vin = 3.3V OUTPUT CURRENT, Io (A) EFFICIENCY, (%) 90 Vin = 3.9V 85 80 75 70 0 2.5m/s 500 LFM 30 95 5 10 15 20 25 25 NC 20 1m/s 200 LFM 15 1.5m/s 300 LFM 2.0m/s 400 LFM 10 5 0 30 30 40 50 60 70 80 O OUTPUT CURRENT, IO (A) Figure 13. Converter Efficiency versus Output Current. 0.5m/s 100 LFM AMBIENT TEMPERATURE, TA C Figure 16. Output Current Derating versus Ambient Temperature and Airflow (ATM030A0X3-SR). 35 OUTPUT CURRENT, Io (A) VO (V) (20mV/div) OUTPUT VOLTAGE 2.5m/s (500LFM) 30 NC 0.5m/s (100LFM) 25 1m/s (200LFM) 1.5m/s (300LFM) 20 2m/s (400LFM) 15 30 Figure 15. Transient Response to Dynamic Load Change from 0% to 50% to 0% of full load. LINEAGE POWER 60 70 80 OUTPUT VOLTAGE VO (V) (1V/div) Figure 17. Output Current Derating versus Ambient Temperature and Airflow (ATM030A0X3-SRH). VIN (V) (1V/div) VO (V) (200mV/div) IO (A) (5A/div) TIME, t (50s /div) 50 O INPUT VOLTAGE OUTPUT VOLTAGE OUTPUT CURRENT, Figure 14. Typical output ripple and noise (VIN = VIN,NOM, Io = Io,max). 40 AMBIENT TEMPERATURE, TA C TIME, t (1s/div) TIME, t (5ms/div) Figure 18. Typical Start-up Using Input Voltage (VIN = VIN,NOM, Io = Io,max). 8 Austin MegaLynxTM SMT: Non-Isolated DC-DC Power Modules: 2.7 - 4.0Vdc input; 0.8 to 2.0Vdc Output; 30A output current Data Sheet September 10, 2013 Characteristic Curves The following figures provide typical characteristics for the ATM030A0X3-SR and -SRH (2.0V, 30A) at 25oC. 100 35 2.5m/s 500 LFM Vin = 3.0V 30 90 Vin = 3.3V OUTPUT CURRENT, Io (A) EFFICIENCY, (%) 95 Vin = 3.9V 85 80 75 70 0 5 10 15 20 25 25 1m/s 200 LFM 1.5m/s 300 LFM 15 2.0m/s 400 LFM 10 5 0 30 30 40 50 60 70 80 O OUTPUT CURRENT, IO (A) Figure 19. Converter Efficiency versus Output Current. 0.5m/s 100 LFM NC 20 AMBIENT TEMPERATURE, TA C Figure 22. Output Current Derating versus Ambient Temperature and Airflow (ATM030A0X3-SR). 35 OUTPUT CURRENT, Io (A) VO (V) (20mV/div) OUTPUT VOLTAGE 2.5m/s (500LFM) 30 NC 25 0.5m/s (100LFM) 1m/s (200LFM) 1.5m/s (300LFM) 20 2m/s (400LFM) 15 30 Figure 21. Transient Response to Dynamic Load Change from 0% to 50% to 0% of full load. LINEAGE POWER 60 70 80 OUTPUT VOLTAGE VO (V) (1V/div) Figure 23. Output Current Derating versus Ambient Temperature and Airflow (ATM030A0X3-SRH). VIN (V) (1V/div) VO (V) (200mV/div) IO (A) (5A/div) TIME, t (50s /div) 50 O INPUT VOLTAGE OUTPUT VOLTAGE OUTPUT CURRENT, Figure 20. Typical output ripple and noise (VIN = VIN,NOM, Io = Io,max). 40 AMBIENT TEMPERATURE, TA C TIME, t (1s/div) TIME, t (5ms/div) Figure 24. Typical Start-up Using Input Voltage (VIN = VIN,NOM, Io = Io,max). 9 Austin MegaLynxTM SMT: Non-Isolated DC-DC Power Modules: 2.7 - 4.0Vdc input; 0.8 to 2.0Vdc Output; 30A output current Data Sheet September 10, 2013 Design Considerations CURRENT PROBE TO OSCILLOSCOPE LTEST VIN(+) BATTERY 1H CS CIN 220F Min 150F E.S.R.<0.1 @ 20C 100kHz COM NOTE: Measure input reflected ripple current with a simulated source inductance (LTEST) of 1H. Capacitor CS offsets possible battery impedance. Measure current as shown above. Figure 25. Input Reflected Ripple Current Test Setup. COPPER STRIP VO (+) RESISTIVE LOAD 1uF . 10uF SCOPE COM The ATM030 module should be connected to a lowimpedance source. A highly inductive source can affect the stability of the module. An input capacitor must be placed directly adjacent to the input pin of the module, to minimize input ripple voltage and ensure module stability. To minimize input voltage ripple, low-ESR ceramic capacitors are recommended at the input of the module. Figure 28 shows the input ripple voltage for various output voltages at 30A of load current with 1x47 F or 2x47 F ceramic capacitors and an input of 3.3V. 100 Input Ripple Voltage (mVp-p) Test Configurations 90 80 70 60 1 x 47uF 50 2 x 47uF 40 0.5 1 1.5 2 GROUND PLANE NOTE: All voltage measurements to be taken at the module terminals, as shown above. If sockets are used then Kelvin connections are required at the module terminals to avoid measurement errors due to socket contact resistance. Figure 26. Output Ripple and Noise Test Setup. Rdistribution Rcontact Rcontact VIN(+) RLOAD VO VIN Rdistribution Rcontact Rcontact COM Rdistribution VO Rdistribution COM NOTE: All voltage measurements to be taken at the module terminals, as shown above. If sockets are used then Kelvin connections are required at the module terminals to avoid measurement errors due to socket contact resistance. Figure 27. Output Voltage and Efficiency Test Setup. VO. IO Efficiency = LINEAGE POWER VIN. IIN x 100 % Output Voltage (Vdc) Figure 28. Input ripple voltage for various output voltages with 1x47 F or 2x47 F ceramic capacitors at the input (30A load). Input voltage is 3.3V. Safety Considerations For safety agency approval the power module must be installed in compliance with the spacing and separation requirements of the end-use safety agency standards, i.e., UL 60950, CSA C22.2 No. 60950-00, EN60950 (VDE 0850) (IEC60950, 3rd edition) Licensed. For the converter output to be considered meeting the requirements of safety extra-low voltage (SELV), the input must meet SELV requirements. The power module has extra-low voltage (ELV) outputs when all inputs are ELV. An input fuse for the module is recommended. As an option to using a fuse, no fuse is required, if the module is powered by a power source with current 10 Data Sheet September 10, 2013 Austin MegaLynxTM SMT: Non-Isolated DC-DC Power Modules: 2.7 - 4.0Vdc input; 0.8 to 2.0Vdc Output; 30A output current limit protection and the module is evaluated in the end-use equipment. Feature Descriptions Remote On/Off The ATM030 SMT power modules feature a On/Off pin for remote On/Off operation. If not using the On/Off pin, connect the pin to ground (the module will be ON). The On/Off signal (Von/off) is referenced to ground. Circuit configuration for remote On/Off operation of the module using the On/Off pin is shown in Figure 29. During a Logic High on the On/Off pin (transistor Q1 is OFF), the module remains OFF. The external resistor RX should be chosen to maintain 2.5V minimum on the On/Off pin to ensure that the module is OFF when transistor Qx is in the OFF state. A suitable values for RX is 3K for 5Vin. During Logic-Low when QX is turned ON, the module is turned ON. (See Figure 30). The voltage between the Sense pin and Vo pin must not exceed 0.5V. The amount of power delivered by the module is defined as the output voltage multiplied by the output current (Vo x Io). When using Remote Sense, the output voltage of the module can increase, which if the same output is maintained, increases the power output by the module. Make sure that the maximum output power of the module remains at or below the maximum rated power. When the Remote Sense feature is not being used, connect the Remote Sense pin to output of the module. R d istrib u tio n R co n ta c t R c o nta ct V IN (+ ) S e n se R LO AD R d istrib u tio n R co n ta c t R c o nta ct COM VIN + MODULE R1 Therm al SD I ON/OFF ON /OFF 1K + VON/OFF PW M Enable 100K Q1 10K GN D _ Figure 29. Remote On/Off Implementation using ON/OFF . R d istrib utio n VO R d istrib utio n COM Figure 30. Effective Circuit Configuration for Remote Sense operation. Over Current Protection To provide protection in a fault (output overload) condition, the unit is equipped with internal current-limiting circuitry and can endure current limiting continuously. At the point of current-limit inception, the unit enters hiccup mode. The unit operates normally once the output current is brought back into its specified range. The average output current during hiccup is 10% IO, max. Over Temperature Protection The On/Off pin can also be used to synchronize the output voltage start-up and shutdown of multiple modules in parallel. By connecting On/Off pins of multiple modules, the output start-up can be synchronized (please refer to characterization curves). When On/Off pins are connected together, all modules will shutdown if any one of the modules gets disabled due to undervoltage lockout or over temperature protection. Remote Sense The ATM030 power modules have a Remote Sense feature to minimize the effects of distribution losses by regulating the voltage at the Remote Sense pin LINEAGE POWER To provide protection in a fault condition, the unit is equipped with a thermal shutdown circuit. The unit will shutdown if the overtemperature threshold of o 125 C is exceeded at the thermal reference point Tref. The thermal shutdown is not intended as a guarantee that the unit will survive temperatures beyond its rating. Once the unit goes into thermal shutdown it will then wait to cool before attempting to restart. Input Under Voltage Lockout At input voltages below the input undervoltage lockout limit, the module operation is disabled. The module will begin to operate at an input voltage above the undervoltage lockout turn-on threshold. 11 Data Sheet September 10, 2013 Austin MegaLynxTM SMT: Non-Isolated DC-DC Power Modules: 2.7 - 4.0Vdc input; 0.8 to 2.0Vdc Output; 30A output current Output Voltage Programming Voltage Sequencing The output voltage of the ATM030 module can be programmed to any voltage from 0.8dc to 2.0Vdc by connecting a resistor (shown as Rtrim in Figure 31) between Trim and GND pins of the module. Without an external resistor between Trim and GND pins, the output of the module will be 0.8Vdc. To calculate the value of the trim resistor, Rtrim for a desired output voltage, use the following equation: The Austin MegaLynxTM series of modules include a sequencing feature that enables users to implement various types of output voltage sequencing in their applications. This is accomplished via an additional sequencing pin. When not using the sequencing feature, either leave the SEQ pin unconnected or tied to VIN. 1200 Rtrim = - 100 Vo - 0 . 80 Vo Rmargin-down Rtrim is the external resistor in Austin Lynx or Lynx II Series Vo is the desired output voltage By using a 0.5% tolerance trim resistor with a TC of 100ppm, a set point tolerance of 1.5% can be achieved as specified in the electrical specification. The POL Programming Tool, available at www.lineagepower.com under the Design Tools section, helps determine the required external trim resistor needed for a specific output voltage. Q2 Trim Rmargin-up Rtrim Q1 V IN(+) V O(+) ON/OFF TRIM GND LOAD Rtrim GND Figure 31. Circuit configuration to program output voltage using an external resistor. Voltage Margining Output voltage margining can be implemented in the Austin MegaLynxTM modules by connecting a resistor, Rmargin-up, from the Trim pin to the ground pin for margining-up the output voltage and by connecting a resistor, Rmargin-down, from the Trim pin to output pin for margining-down. Figure 32 shows the circuit configuration for output voltage margining. The POL Programming Tool, available at www.lineagepower.com under the Design Tools section, also calculates the values of Rmargin-up and Rmargin-down for a specific output voltage and % margin. Please consult your local Lineage Power technical representative for additional details. LINEAGE POWER Figure 32. Circuit Configuration for margining Output voltage. For proper voltage sequencing, first, input voltage is applied to the module. The On/Off pin of the module is or tied to GND so that the module is ON by default. After applying input voltage to the module, a minimum of 10msec delay is required before applying voltage on the SEQ pin. After 10msec delay, an analog voltage is applied to the SEQ pin and the output voltage of the module will track this voltage on a one-to-one volt bases until output reaches the set-point voltage. To initiate simultaneous shutdown of the modules, the SEQ pin voltage is lowered in a controlled manner. Output voltage of the modules tracks the voltages below their set-point voltages on a one-to-one basis. A valid input voltage must be maintained until the tracking and output voltages reach ground potential. TM When using the EZ-SEQUENCE feature to control start-up of the module, pre-bias immunity feature during start-up is disabled. The pre-bias immunity feature of the module relies on the module being in the diode-mode during start-up. When TM using the EZ-SEQUENCE feature, modules goes through an internal set-up time of 10msec, and will be in synchronous rectification mode when voltage 12 Data Sheet September 10, 2013 Austin MegaLynxTM SMT: Non-Isolated DC-DC Power Modules: 2.7 - 4.0Vdc input; 0.8 to 2.0Vdc Output; 30A output current at the SEQ pin is applied. This will result in sinking current in the module if pre-bias voltage is present at the output of the module. When pre-bias immunity during start-up is required, the EZTM SEQUENCE feature must be disabled. For TM additional guidelines on using EZ-SEQUENCE feature of Austin MegaLynx modules, contact the Tyco Power Systems Technical representative for the application note on output voltage sequencing. Active Load Sharing (-P Option) For additional power requirements, the ATM030 series power module is also available with a parallel option. Up to five modules can be configured, in parallel, with active load sharing. Good layout techniques should be observed when using multiple units in parallel. To implement forced load sharing, the following connections should be made: * The share pins of all units in parallel must be connected together. The path of these connections should be as direct as possible. * All remote-sense pins should be connected to the power bus at the same point, i.e., connect all the SENSE(+) pins to the (+) side of the bus. Close proximity and directness are necessary for good noise immunity Some special considerations apply for design of converters in parallel operation: When sizing the number of modules required for parallel operation, take note of the fact that current sharing has some tolerance. In addition, under transient condtions such as a dynamic load change and during startup, all converter output currents will not be equal. To allow for such variation and avoid the likelihood of a converter shutting off due to a current overload, the total capacity of the paralleled system should be no more than 75% of the sum of the individual converters. As an example, for a system of four ATM030A0X3-SR converters the parallel, the total current drawn should be less that 75% of 4 x 30A or 90A. * * All modules should be turned on and off together. This is so that all modules come up at the same time avoiding the problem of one converter sourcing current into the other leading to an overcurrent trip condition. To ensure that all modules come up simultaneously, the on/off pins of all paralleled converters should be tied together and the converters enabled and disabled using the on/off pin. * The share bus is not designed for redundant operation and the system will be non-functional upon failure of one of the unit when multiple units are in parallel. In particular, if one of the converters shuts down during operation, the other converters may also shut down due to their outputs hitting current limit. In such a situation, unless a coordinated restart is ensured, the system may never properly restart since different converters will try to restart at different times causing an overload condition and subsequent shutdown. This situation can be avoided by having an external output voltage monitor circuit that detects a shutdown condition and forces all converters to shut down and restart together. When not using the parallel feature, leave the share pin open. When sizing the number of modules required for parallel operation, take note of the fact that current sharing has some tolerance. In addition, under transient condtions such as a dynamic load change and during startup, all converter output currents will not be equal. To allow for such variation and avoid the likelihood of a converter shutting off due to a current overload, the total capacity of the paralleled system should be no more than 75% of the sum of the individual converters. As an example, for a system of four ATM030A0X3SR converters the parallel, the total current drawn should be less that 75% of (4 x 30A) , i.e. less than 90A. LINEAGE POWER 13 Austin MegaLynxTM SMT: Non-Isolated DC-DC Power Modules: 2.7 - 4.0Vdc input; 0.8 to 2.0Vdc Output; 30A output current Data Sheet September 10, 2013 Thermal Considerations Power modules operate in a variety of thermal environments; however, sufficient cooling should always be provided to help ensure reliable operation. Considerations include ambient temperature, airflow, module power dissipation, and the need for increased reliability. A reduction in the operating temperature of the module will result in an increase in reliability. The thermal data presented here is based on physical measurements taken in a wind tunnel. The test set-up is shown in Figure 33. Note that the airflow is parallel to the long axis of the module as shown in Figure 34. The derating data applies to airflow in either direction of the module's long axis. Figure 34. Airflow direction for thermal testing. 25.4_ (1.0) Wind Tunnel PWBs Power Module 76.2_ (3.0) x 12.7_ (0.50) Probe Location for measuring airflow and ambient temperature Figure 35. Tref Temperature measurement location. The thermal reference points, Tref used in the specifications are shown in Figure 35. For reliable operation the temperatures at these points should not exceed 125oC. The output power of the module should not exceed the rated power of the module (Vo,set x Io,max). Please refer to the Application Note "Thermal Characterization Process For Open-Frame BoardMounted Power Modules" for a detailed discussion of thermal aspects including maximum device temperatures. Air flow Figure 33. Thermal Test Up LINEAGE POWER 14 Data Sheet September 10, 2013 Austin MegaLynxTM SMT: Non-Isolated DC-DC Power Modules: 2.7 - 4.0Vdc input; 0.8 to 2.0Vdc Output; 30A output current Mechanical Outline of Module (ATM030A0X3-SRPH) Dimensions are in millimeters and (inches). Tolerances: x.x mm 0.5 mm (x.xx in. 0.02 in.) [unless otherwise indicated] x.xx mm 0.25 mm (x.xxx in 0.010 in.) Note: For the ATM030A0X3-SRH module, the SHARE pin is omitted since these modules are not capable of being paralleled. LINEAGE POWER 15 Data Sheet September 10, 2013 Austin MegaLynxTM SMT: Non-Isolated DC-DC Power Modules: 2.7 - 4.0Vdc input; 0.8 to 2.0Vdc Output; 30A output current Recommended Pad Layout (ATM030A0X3-SRPH) Dimensions are in millimeters and (inches). Tolerances: x.x mm 0.5 mm (x.xx in. 0.02 in.) [unless otherwise indicated] x.xx mm 0.25 mm (x.xxx in 0.010 in.) Pin 8 Pin 10 PIN FUNCTION PIN 1 On/Off 6 FUNCTION Trim 2 VIN 7 Sense 3 SEQ 8 GND 4 GND 9 SHARE 5 VOUT 10 GND Note: For the ATM030A0X3-SRH module, the SHARE pin is not present since these modules are not capable of being paralleled. LINEAGE POWER 16 Data Sheet September 10, 2013 Austin MegaLynxTM SMT: Non-Isolated DC-DC Power Modules: 2.7 - 4.0Vdc input; 0.8 to 2.0Vdc Output; 30A output current Mechanical Outline of Module (ATM030A0X3-SRP) Dimensions are in millimeters and (inches). Tolerances: x.x mm 0.5 mm (x.xx in. 0.02 in.) [unless otherwise indicated] x.xx mm 0.25 mm (x.xxx in 0.010 in.) Note: For the ATM030A0X3-SR module, the SHARE pin is omitted since these modules are not capable of being paralleled. LINEAGE POWER 17 Data Sheet September 10, 2013 Austin MegaLynxTM SMT: Non-Isolated DC-DC Power Modules: 2.7 - 4.0Vdc input; 0.8 to 2.0Vdc Output; 30A output current Recommended Pad Layout (ATM030A0X3-SRP) Dimensions are in millimeters and (inches). Tolerances: x.x mm 0.5 mm (x.xx in. 0.02 in.) [unless otherwise indicated] x.xx mm 0.25 mm (x.xxx in 0.010 in.) PIN FUNCTION PIN 1 On/Off 6 FUNCTION Trim 2 VIN 7 Sense 3 SEQ 8 No Pin 4 GND 9 Share 5 VOUT 10 No Pin Note: For the ATM030A0X3-SR module, the SHARE pin is not used since these modules are not capable of being paralleled. LINEAGE POWER 18 Data Sheet September 10, 2013 Austin MegaLynxTM SMT: Non-Isolated DC-DC Power Modules: 2.7 - 4.0Vdc input; 0.8 to 2.0Vdc Output; 30A output current Packaging Details The ATM030 SMT module is supplied in tape & reel as standard. Modules are shipped in quantities of 200 modules per reel. All Dimensions are in millimeters and (in inches). Reel Dimensions Outside diameter: Inside diameter: Tape Width: LINEAGE POWER 330.2 (13.0) 177.8 (7.0) 44.0 (1.73) 19 Data Sheet September 10, 2013 Austin MegaLynxTM SMT: Non-Isolated DC-DC Power Modules: 2.7 - 4.0Vdc input; 0.8 to 2.0Vdc Output; 30A output current Surface Mount Information Pick and Place TM The Austin MegaLynx SMT modules use an open frame construction and are designed for a fully automated assembly process. The modules are fitted with a label designed to provide a large surface area for pick and place operations. The label meets all the requirements for surface mount processing, as well as safety standards, and is able to withstand reflow o temperatures of up to 300 C. The label also carries product information such as product code, serial number and location of manufacture. In a conventional Tin/Lead (Sn/Pb) solder process peak reflow temperatures are limited to less than 235oC. Typically, the eutectic solder melts at 183oC, wets the land, and subsequently wicks the device connection. Sufficient time must be allowed to fuse the plating on the connection to ensure a reliable solder joint. There are several types of SMT reflow technologies currently used in the industry. These surface mount power modules can be reliably soldered using natural forced convection, IR (radiant infrared), or a combination of convection/IR. For reliable soldering the solder reflow profile should be established by accurately measuring the modules CP connector temperatures. 300 P eak Temp 235oC REFLOW TEMP (C) 250 200 150 So ak zo ne 30-240s 100 0 Nozzle Recommendations Tin Lead Soldering The ATM030 modules are lead free modules and can be soldered either in a lead-free solder process or in a conventional Tin/Lead (Sn/Pb) process. It is recommended that the customer review data sheets in order to customize the solder reflow profile for each application board assembly. The following instructions must be observed when soldering these units. Failure to observe these instructions may result in the failure of or cause damage to the modules, and can adversely affect long-term reliability. LINEAGE POWER REFLOW TIME (S) Figure 37. Reflow Profile for Tin/Lead (Sn/Pb) process. 240 235 MAX TEMP SOLDER (C) The module weight has been kept to a minimum by using open frame construction. Even so, these modules have a relatively large mass when compared to conventional SMT components. Variables such as nozzle size, tip style, vacuum pressure and pick & placement speed should be considered to optimize this process. The minimum recommended inside nozzle diameter for reliable operation is 3mm. The maximum nozzle outer diameter, which will safely fit within the allowable component spacing, is 5 mm max. Tlim above 205oC P reheat zo ne max 4oCs -1 50 Figure 36. Pick and Place Location. Co o ling zo ne 1-4oCs -1 Heat zo ne max 4oCs -1 230 225 220 215 210 205 200 0 10 20 30 40 50 60 Figure 38. Time Limit Curve Above 205oC Reflow for Tin Lead (Sn/Pb) process. 20 Austin MegaLynxTM SMT: Non-Isolated DC-DC Power Modules: 2.7 - 4.0Vdc input; 0.8 to 2.0Vdc Output; 30A output current Surface Mount Information (continued) Lead Free Soldering The -Z version MegaLynx ATM SMT modules are lead-free (Pb-free) and RoHS compliant and are both forward and backward compatible in a Pb-free and a SnPb soldering process. Failure to observe the instructions below may result in the failure of or cause damage to the modules and can adversely affect long-term reliability. Pb-free Reflow Profile Power Systems will comply with J-STD-020 Rev. C (Moisture/Reflow Sensitivity Classification for Nonhermetic Solid State Surface Mount Devices) for both Pb-free solder profiles and MSL classification procedures. This standard provides a recommended forced-air-convection reflow profile based on the volume and thickness of the package (table 4-2). The suggested Pb-free solder paste is Sn/Ag/Cu (SAC). The recommended linear reflow profile using Sn/Ag/Cu solder is shown in Figure 39. Modules: Soldering and Cleaning Application Note (AN04-001). 300 Per J-STD-020 Rev. C Peak Temp 260C 250 Reflow Temp (C) Data Sheet September 10, 2013 200 150 * Min. Time Above 235C 15 Seconds Heating Zone 1C/Second Cooling Zone *Time Above 217C 60 Seconds 100 50 0 Reflow Time (Seconds) Figure 39. Recommended linear reflow profile using Sn/Ag/Cu solder. MSL Rating The Austin MegaLynxTM ATM SMT modules have a MSL rating of 2a. Storage and Handling The recommended storage environment and handling procedures for moisture-sensitive surface mount packages is detailed in J-STD-033 Rev. A (Handling, Packing, Shipping and Use of Moisture/Reflow Sensitive Surface Mount Devices). Moisture barrier bags (MBB) with desiccant are required for MSL ratings of 2 or greater. These sealed packages should not be broken until time of use. Once the original package is broken, the floor life of the product at conditions of 30C and 60% relative humidity varies according to the MSL rating (see J-STD-033A). The shelf life for dry packed SMT packages will be a minimum of 12 months from the bag seal date, when stored at the following conditions: < 40 C, < 90% relative humidity. Post Solder Cleaning and Drying Considerations Post solder cleaning is usually the final circuit-board assembly process prior to electrical board testing. The result of inadequate cleaning and drying can affect both the reliability of a power module and the testability of the finished circuit-board assembly. For guidance on appropriate soldering, cleaning and drying procedures, refer to Board Mounted Power LINEAGE POWER 21 Austin MegaLynxTM SMT: Non-Isolated DC-DC Power Modules: 2.7 - 4.0Vdc input; 0.8 to 2.0Vdc Output; 30A output current Data Sheet September 10, 2013 Ordering Information Please contact your Lineage Power Sales Representative for pricing, availability and optional features. Table 1: Device Codes ATM030A0X3-SR Input Voltage 2.7 - 4.0Vdc Output Voltage 0.8 - 2.0Vdc Output Current 30A On/Off Logic Negative Connector Type SMT CC109112315 ATM030A0X3-SRZ 2.7 - 4.0Vdc 0.8 - 2.0Vdc 30A Negative SMT CC109112397 ATM030A0X3-SRH 2.7 - 4.0Vdc 0.8 - 2.0Vdc 30A Negative SMT CC109112323 ATM030A0X3-SRHZ 2.7 - 4.0Vdc 0.8 - 2.0Vdc 30A Negative SMT CC109112406 Product codes Comcodes ATM030A0X3-SRPH 2.7 - 4.0Vdc 0.8 - 2.0Vdc 30A Negative SMT CC109112331 ATM030A0X3-SRPHZ 2.7 - 4.0Vdc 0.8 - 2.0Vdc 30A Negative SMT CC109112414 Table 2. Device Options Option Device Code Suffix Current Share -P 2 Extra ground pins -H RoHS Compliant -Z Asia-Pacific Headquarters Tel: +65 6593 7211 World Wide Headquarters Lineage Power Corporation 601 Shiloh Road, Plano, TX 75074, USA +1-800-526-7819 (Outside U.S.A.: +1-972-244-9428) www.lineagepower.com e-mail: techsupport1@lineagepower.com Europe, Middle-East and Africa Headquarters Tel: +49 89 878067-280 India Headquarters Tel: +91 80 28411633 Lineage Power reserves the right to make changes to the product(s) or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Lineage Power DC-DC products are protected under various patents. Information on these patents is available at www.lineagepower.com/patents. (c) 2009 Lineage Power Corporation, (Plano, Texas) All International Rights Reserved. LINEAGE POWER 22 Document No: DS06-130 ver. 1.09 PDF No: ATM030A0X3-SR_ds.pdf