LM2671 SIMPLE SWITCHER Power Converter High Efficiency 500mA StepDown Voltage Regulator with Features General Description The LM2671 series of regulators are monolithic integrated circuits built with a LMDMOS process. These regulators provide all the active functions for a step-down (buck) switching regulator, capable of driving a 500mA load current with excellent line and load regulation. These devices are available in fixed output voltages of 3.3V, 5.0V, 12V, and an adjustable output version. Requiring a minimum number of external components, these regulators are simple to use and include patented internal frequency compensation (Patent Nos. 5,382,918 and 5,514,947), fixed frequency oscillator, external shutdown, soft-start, and frequency synchronization. The LM2671 series operates at a switching frequency of 260 kHz, thus allowing smaller sized filter components than what would be needed with lower frequency switching regulators. Because of its very high efficiency (>90%), the copper traces on the printed circuit board are the only heat sinking needed. A family of standard inductors for use with the LM2671 are available from several different manufacturers. This feature greatly simplifies the design of switch-mode power supplies using these advanced ICs. Also included in the datasheet are selector guides for diodes and capacitors designed to work in switch-mode power supplies. Other features include a guaranteed 1.5% tolerance on output voltage within specified input voltages and output load conditions, and 10% on the oscillator frequency. External shutdown is included, featuring typically 50 A stand-by current. The output switch includes current limiting, as well as thermal shutdown for full protection under fault conditions. To simplify the LM2671 buck regulator design procedure, there exists computer design software, LM267X Made Simple (version 6.0). Features Efficiency up to 96% Available in SO-8, 8-pin DIP and LLP packages Computer Design Software LM267X Made Simple (version 6.0) Simple and easy to design with Requires only 5 external components Uses readily available standard inductors 3.3V, 5.0V, 12V, and adjustable output versions Adjustable version output voltage range: 1.21V to 37V 1.5% max output voltage tolerance over line and load conditions Guaranteed 500mA output load current 0.25 DMOS Output Switch Wide input voltage range: 8V to 40V 260 kHz fixed frequency internal oscillator TTL shutdown capability, low power standby mode Soft-start and frequency synchronization Thermal shutdown and current limit protection Applications Simple High Efficiency (>90%) Step-Down (Buck) Regulator Efficient Pre-Regulator for Linear Regulators Typical Application (Fixed Output Voltage Versions) 10004201 SIMPLE SWITCHER(R) is a registered trademark of National Semiconductor Corporation WEBENCH(R) is a registered trademark of National Semiconductor Corporation. Windows(R) is a registered trademark of Microsoft Corporation. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. 100042 SNVS008H Copyright (c) 1999-2012, Texas Instruments Incorporated LM2671 Connection Diagrams 16-Lead LLP Surface Mount Package Top View 8-Lead Package Top View 10004202 SO-8/DIP Package See NSC Package Drawing Number MO8A/N08E 10004241 LLP Package See NSC Package Drawing Number LDA16A TABLE 1. Package Marking and Ordering Information Output Voltage Order Information Package Marking Supplied as: 12 LM2671LD-12 S0005B 1000 Units on Tape and Reel 12 LM2671LDX-12 S0005B 4500 Units on Tape and Reel 3.3 LM2671LD-3.3 S0006B 1000 Units on Tape and Reel 3.3 LM2671LDX-3.3 S0006B 4500 Units on Tape and Reel 5.0 LM2671LD-5.0 S0007B 1000 Units on Tape and Reel 5.0 LM2671LDX-5.0 S0007B 4500 Units on Tape and Reel ADJ LM2671LD-ADJ S0008B 1000 Units on Tape and Reel ADJ LM2671LDX-ADJ S0008B 4500 Units on Tape and Reel 12 LM2671M-12 2671M-12 Shipped in Anti-Static Rails 16 Lead LLP SO-8 12 LM2671MX-12 2671M-12 2500 Units on Tape and Reel 3.3 LM2671M-3.3 2671M-3.3 Shipped in Anti-Static Rails 3.3 LM2671MX-3.3 2671M-3.3 2500 Units on Tape and Reel 5.0 LM2671M-5.0 2671M-5.0 Shipped in Anti-Static Rails 5.0 LM2671MX-5.0 2671M-5.0 2500 Units on Tape and Reel ADJ LM2671M-ADJ 2671M-ADJ Shipped in Anti-Static Rails ADJ LM2671MX-ADJ 2671M-ADJ 2500 Units on Tape and Reel DIP 2 12 LM2671N-12 LM2671N-12 Shipped in Anti-Static Rails 3.3 LM2671N-3.3 LM2671N-3.3 Shipped in Anti-Static Rails 5.0 LM2671N-5.0 LM2671N-5.0 Shipped in Anti-Static Rails ADJ LM2671N-ADJ LM2671N-ADJ Shipped in Anti-Static Rails Copyright (c) 1999-2012, Texas Instruments Incorporated LM2671 Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and specifications. Supply Voltage 45V ON/OFF Pin Voltage -0.1V VSH 6V Switch Voltage to Ground Boost Pin Voltage Feedback Pin Voltage -1V VSW + 8V -0.3V VFB 14V ESD Susceptibility Human Body Model (Note 2) Power Dissipation Storage Temperature Range Lead Temperature M Package Vapor Phase (60s) Infrared (15s) N Package (Soldering, 10s) LLP Package (See AN-1187) Maximum Junction Temperature 2 kV Internally Limited -65C to +150C +215C +220C +260C +150C Operating Ratings Supply Voltage Temperature Range 6.5V to 40V -40C TJ +125C Electrical Characteristics LM2671-3.3 Specifications with standard type face are for TJ = 25C, and those in bold type face apply over full Operating Temperature Range. Symbol Parameter Conditions Typical (Note 4) Min (Note 5) Max (Note 5) Units SYSTEM PARAMETERS Test Circuit Figure 2 (Note 3) VOUT Output Voltage VIN = 8V to 40V, ILOAD = 20 mA to 500 mA 3.3 3.251/3.201 3.350/3.399 V VOUT Output Voltage VIN = 6.5V to 40V, ILOAD = 20 mA to 250 mA 3.3 3.251/3.201 3.350/3.399 V Efficiency VIN = 12V, ILOAD = 500 mA 86 % LM2671-5.0 Symbol Parameter Conditions Typical (Note 4) Min (Note 5) Max (Note 5) Units SYSTEM PARAMETERS Test Circuit Figure 2 (Note 3) VOUT Output Voltage VIN = 8V to 40V, ILOAD = 20 mA to 500 mA 5.0 4.925/4.850 5.075/5.150 V VOUT Output Voltage VIN = 6.5V to 40V, ILOAD = 20 mA to 250 mA 5.0 4.925/4.850 5.075/5.150 V Efficiency VIN = 12V, ILOAD = 500 mA 90 % LM2671-12 Symbol Parameter Conditions Typical (Note 4) Min (Note 5) Max (Note 5) Units 11.82/11.64 12.18/12.36 V SYSTEM PARAMETERS Test Circuit Figure 2 (Note 3) VOUT Output Voltage VIN = 15V to 40V, ILOAD = 20 mA to 500 mA 12 Efficiency VIN = 24V, ILOAD = 500 mA 94 Copyright (c) 1999-2012, Texas Instruments Incorporated % 3 LM2671 LM2671-ADJ Symbol Parameter Conditions Typ (Note 4) Min (Note 5) Max (Note 5) Units 1.210 1.192/1.174 1.228/1.246 V 1.210 1.192/1.174 1.228/1.246 V SYSTEM PARAMETERS Test Circuit Figure 3 (Note 3) VFB Feedback Voltage VIN = 8V to 40V, ILOAD = 20 mA to 500 mA VOUT Programmed for 5V (see Circuit of Figure 3) VFB Feedback Voltage VIN = 6.5V to 40V, ILOAD = 20 mA to 250 mA VOUT Programmed for 5V (see Circuit of Figure 3) Efficiency VIN = 12V, ILOAD = 500 mA 90 % All Output Voltage Versions Specifications with standard type face are for TJ = 25C, and those in bold type face apply over full Operating Temperature Range. Unless otherwise specified, VIN = 12V for the 3.3V, 5V, and Adjustable versions and VIN = 24V for the 12V version, and ILOAD = 100 mA. Symbol Parameters Conditions Typ Min Max Units 3.6 mA DEVICE PARAMETERS IQ Quiescent Current VFEEDBACK = 8V 2.5 For 3.3V, 5.0V, and ADJ Versions VFEEDBACK = 15V 2.5 mA For 12V Versions ISTBY Standby Quiescent Current ICL Current Limit IL Output Leakage Current ON/OFF Pin = 0V 50 0.8 VIN = 40V, ON/OFF Pin = 0V 0.62/0.575 100/150 A 1.2/1.25 A 1 25 A 6 15 mA VSWITCH = 0V VSWITCH = -1V, ON/OFF Pin = 0V 0.40/0.60 275 kHz RDS(ON) Switch On-Resistance ISWITCH = 500 mA 0.25 fO Oscillator Frequency Measured at Switch Pin 260 D Maximum Duty Cycle 95 Minimum Duty Cycle 0 % 85 nA IBIAS VS/D Feedback Bias VFEEDBACK = 1.3V Current ADJ Version Only ON/OFF Pin 225 % 1.4 0.8 2.0 7 37 V Voltage Thesholds A IS/D ON/OFF Pin Current ON/OFF Pin = 0V 20 FSYNC Synchronization Frequency VSYNC = 3.5V, 50% duty cycle 400 kHz VSYNC Synchronization Threshold Voltage 1.4 V VSS Soft-Start Voltage 0.63 0.53 0.73 V ISS Soft-Start Current 4.5 1.5 6.9 A JA Thermal Resistance N Package, Junction to Ambient (Note 6) 95 M Package, Junction to Ambient (Note 6) 105 C/W Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but device parameter specifications may not be guaranteed under these conditions. For guaranteed specifications and test conditions, see the Electrical Characteristics. Note 2: The human body model is a 100 pF capacitor discharged through a 1.5 k resistor into each pin. Note 3: External components such as the catch diode, inductor, input and output capacitors, and voltage programming resistors can affect switching regulator performance. When the LM2671 is used as shown in Figure 2 and Figure 3 test circuits, system performance will be as specified by the system parameters section of the Electrical Characteristics. Note 4: Typical numbers are at 25C and represent the most likely norm. 4 Copyright (c) 1999-2012, Texas Instruments Incorporated LM2671 Note 5: All limits guaranteed at room temperature (standard type face) and at temperature extremes (bold type face). All room temperature limits are 100% production tested. All limits at temperature extremes are guaranteed via correlation using standard Statistical Quality Control (SQC) methods. All limits are used to calculate Average Outgoing Quality Level (AOQL). Note 6: Junction to ambient thermal resistance with approximately 1 square inch of printed circuit board copper surrounding the leads. Additional copper area will lower thermal resistance further. See Application Information section in the application note accompanying this datasheet and the thermal model in LM267X Made Simple version 6.0 software. The value J-A for the LLP (LD) package is specifically dependent on PCB trace area, trace material, and the number of layers and thermal vias. For improved thermal resistance and power dissipation for the LLP package, refer to Application Note AN-1187. Copyright (c) 1999-2012, Texas Instruments Incorporated 5 LM2671 Typical Performance Characteristics Normalized Output Voltage Line Regulation 10004204 10004203 Efficiency Drain-to-Source Resistance 10004205 10004206 Switch Current Limit Operating Quiescent Current 10004207 10004208 6 Copyright (c) 1999-2012, Texas Instruments Incorporated LM2671 Standby Quiescent Current ON/OFF Threshold Voltage 10004209 ON/OFF Pin Current (Sourcing) 10004210 Switching Frequency 10004212 10004211 Feedback Pin Bias Current Peak Switch Current 10004213 Copyright (c) 1999-2012, Texas Instruments Incorporated 10004214 7 LM2671 Dropout Voltage--3.3V Option Dropout Voltage--5.0V Option 10004215 10004216 Block Diagram 10004217 * Patent Number 5,514,947 Patent Number 5,382,918 FIGURE 1. 8 Copyright (c) 1999-2012, Texas Instruments Incorporated LM2671 Typical Performance Characteristics Continuous Mode Switching Waveforms VIN = 20V, VOUT = 5V, ILOAD = 500 mA L = 100 H, COUT = 100 F, COUTESR = 0.1 (Circuit of Figure 2) Discontinuous Mode Switching Waveforms VIN = 20V, VOUT = 5V, ILOAD = 300 mA L = 15 H, COUT = 68 F (2x), COUTESR = 25 m 10004218 A: VSW Pin Voltage, 10 V/div. B: Inductor Current, 0.2 A/div C: Output Ripple Voltage, 50 mV/div AC-Coupled 10004219 A: VSW Pin Voltage, 10 V/div. B: Inductor Current, 0.5 A/div C: Output Ripple Voltage, 20 mV/div AC-Coupled Horizontal Time Base: 1 s/div Horizontal Time Base: 1 s/div Load Transient Response for Continuous Mode VIN = 20V, VOUT = 5V L = 100 H, COUT = 100 F, COUTESR = 0.1 Load Transient Response for Discontinuous Mode VIN = 20V, VOUT = 5V, L = 47 H, COUT = 68 F, COUTESR = 50 m 10004220 A: Output Voltage, 100 mV/div, AC-Coupled B: Load Current: 100 mA to 500 mA Load Pulse Horizontal Time Base: 50 s/div Copyright (c) 1999-2012, Texas Instruments Incorporated 10004221 A: Output Voltage, 100 mV/div, AC-Coupled B: Load Current: 100 mA to 400 mA Load Pulse Horizontal Time Base: 200 s/div 9 LM2671 Test Circuit and Layout Guidelines 10004222 CIN - 22 F, 50V Tantalum, Sprague "199D Series" COUT - 47 F, 25V Tantalum, Sprague "595D Series" D1 - 3.3A, 50V Schottky Rectifier, IR 30WQ05F L1 - 68 H Sumida #RCR110D-680L CB - 0.01 F, 50V Ceramic FIGURE 2. Standard Test Circuits and Layout Guides Fixed Output Voltage Versions 10004223 CIN - 22 F, 50V Tantalum, Sprague "199D Series" COUT - 47 F, 25V Tantalum, Sprague "595D Series" D1 - 3.3A, 50V Schottky Rectifier, IR 30WQ05F L1 - 68 H Sumida #RCR110D-680L R1 - 1.5 k, 1% CB - 0.01 F, 50V Ceramic For a 5V output, select R2 to be 4.75 k, 1% where VREF = 1.21V Use a 1% resistor for best stability. FIGURE 3. Standard Test Circuits and Layout Guides Adjustable Output Voltage Versions 10 Copyright (c) 1999-2012, Texas Instruments Incorporated LM2671 Application Hints The LM2671 provides all of the active functions required for a step-down (buck) switching regulator. The internal power switch is a DMOS power MOSFET to provide power supply designs with high current capability, up to 0.5A, and highly efficient operation. The LM2671 is part of the SIMPLE SWITCHER(R)(R) family of power converters. A complete design uses a minimum number of external components, which have been pre-determined from a variety of manufacturers. Using either this data sheet or TI's WEBENCH(R) design tool, a complete switching power supply can be designed quickly. Also, refer to the LM2670 data sheet for additional applications information. SWITCH OUTPUT This is the output of a power MOSFET switch connected directly to the input voltage. The switch provides energy to an inductor, an output capacitor and the load circuitry under control of an internal pulse-width-modulator (PWM). The PWM controller is internally clocked by a fixed 260kHz oscillator. In a standard step-down application the duty cycle (Time ON/Time OFF) of the power switch is proportional to the ratio of the power supply output voltage to the input voltage. The voltage on the VSW pin cycles between Vin (switch ON) and below ground by the voltage drop of the external Schottky diode (switch OFF). INPUT The input voltage for the power supply is connected to the VIN pin. In addition to providing energy to the load the input voltage also provides bias for the internal circuitry of the LM2671. For guaranteed performance the input voltage must be in the range of 6.5V to 40V. For best performance of the power supply the VIN pin should always be bypassed with an input capacitor located close to this pin and GND. C BOOST A capacitor must be connected from the CB pin to the VSW pin. This capacitor boosts the gate drive to the internal MOSFET above Vin to fully turn it ON. This minimizes conduction losses in the power switch to maintain high efficiency. The recommended value for C Boost is 0.01F. GROUND This is the ground reference connection for all components in the power supply. In fast-switching, high-current applications such as those implemented with the LM2671, it is recommended that a broad ground plane be used to minimize signal coupling throughout the circuit SYNC This input allows control of the switching clock frequency. If left open-circuited the regulator will be switched at the internal oscillator frequency, typically 260 kHz. An external clock can be used to force the switching frequency and thereby control the output ripple frequency of the regulator. This capability provides for consistent filtering of the output ripple from system to system as well as precise frequency spectrum positioning of the ripple frequency which is often desired in communications and radio applications. This external frequency must be greater than the LM2671 internal oscillator frequency, which could be as high as 275 kHz, to prevent an erroneous reset of the internal ramp oscillator and PWM control of the power switch. The ramp oscillator is reset on the positive going edge of the sync input signal. It is recommended that the external TTL or CMOS compatible clock (between 0V and a level greater than 3V) be ac coupled to the SYNC pin through a 100pF capacitor and a 1K resistor to ground. When the SYNC function is used, current limit frequency foldback is not active. Therefore, the device may not be fully protected against extreme output short circuit conditions. FEEDBACK This is the input to a two-stage high gain amplifier, which drives the PWM controller. Connect the FB pin directly to the output for proper regulation. For the fixed output devices (3.3V, 5V and 12V outputs), a direct wire connection to the output is all that is required as internal gain setting resistors are provided inside the LM2671. For the adjustable output version two external resistors are required to set the dc output voltage. For stable operation of the power supply it is important to prevent coupling of any inductor flux to the feedback input. ON/OFF This input provides an electrical ON/OFF control of the power supply. Connecting this pin to ground or to any voltage less than 0.8V will completely turn OFF the regulator. The current drain from the input supply when OFF is only 50A. The ON/OFF input has an internal pull-up current source of approximately 20A and a protection clamp zener diode of 7V to ground. When electrically driving the ON/OFF pin the high voltage level for the ON condition should not exceed the 6V absolute maximum limit. When ON/ OFF control is not required this pin should be left open. DAP (LLP PACKAGE) The Die Attach Pad (DAP) can and should be connected to the PCB Ground plane/island. For CAD and assembly guidelines refer to Application Note SNAO401 at http://www.ti.com/lit/an/snoa401q/snoa401q.pdf. Copyright (c) 1999-2012, Texas Instruments Incorporated 11 LM2671 LM2671 Series Buck Regulator Design Procedure (Fixed Output) PROCEDURE (Fixed Output Voltage Version) EXAMPLE (Fixed Output Voltage Version) To simplify the buck regulator design procedure, National Semiconductor is making available computer design software to be used with the SIMPLE SWITCHER line of switching regulators. LM267X Made Simple (version 6.0) is available on Windows(R) 3.1, NT, or 95 operating systems. Given: Given: VOUT = Regulated Output Voltage (3.3V, 5V, or 12V) VOUT = 5V VIN(max) = Maximum DC Input Voltage VIN(max) = 12V ILOAD(max) = Maximum Load Current ILOAD(max) = 500 mA 1. Inductor Selection (L1) A. Select the correct inductor value selection guide from Figure 4 and Figure 5 or Figure 6 (output voltages of 3.3V, 5V, or 12V respectively). For all other voltages, see the design procedure for the adjustable version. B. From the inductor value selection guide, identify the inductance region intersected by the Maximum Input Voltage line and the Maximum Load Current line. Each region is identified by an inductance value and an inductor code (LXX). C. Select an appropriate inductor from the four manufacturer's part numbers listed in Figure 8. Each manufacturer makes a different style of inductor to allow flexibility in meeting various design requirements. Listed below are some of the differentiating characteristics of each manufacturer's inductors: Schott: ferrite EP core inductors; these have very low leakage magnetic fields to reduce electro-magnetic interference (EMI) and are the lowest power loss inductors Renco: ferrite stick core inductors; benefits are typically lowest cost inductors and can withstand E*T and transient peak currents above rated value. Be aware that these inductors have an external magnetic field which may generate more EMI than other types of inductors. Pulse: powered iron toroid core inductors; these can also be low cost and can withstand larger than normal E*T and transient peak currents. Toroid inductors have low EMI. Coilcraft: ferrite drum core inductors; these are the smallest physical size inductors, available only as SMT components. Be aware that these inductors also generate EMI--but less than stick inductors. Complete specifications for these inductors are available from the respective manufacturers. A table listing the manufacturers' phone numbers is located in Figure 9. 2. Output Capacitor Selection (COUT) A. Select an output capacitor from the output capacitor table in Figure 10. Using the output voltage and the inductance value found in the inductor selection guide, step 1, locate the appropriate capacitor value and voltage rating. 12 1. Inductor Selection (L1) A. Use the inductor selection guide for the 5V version shown in Figure 5. B. From the inductor value selection guide shown in Figure 5, the inductance region intersected by the 12V horizontal line and the 500 mA vertical line is 47 H, and the inductor code is L13. C. The inductance value required is 47 H. From the table in Figure 8, go to the L13 line and choose an inductor part number from any of the four manufacturers shown. (In most instances, both through hole and surface mount inductors are available.) 2. Output Capacitor Selection (COUT) A. Use the 5.0V section in the output capacitor table in Figure 10. Choose a capacitor value and voltage rating from the line that contains the inductance value of 47 H. The capacitance and voltage rating values corresponding to the 47 H inductor are the: Copyright (c) 1999-2012, Texas Instruments Incorporated LM2671 PROCEDURE (Fixed Output Voltage Version) EXAMPLE (Fixed Output Voltage Version) The capacitor list contains through-hole electrolytic capacitors from four different capacitor manufacturers and surface mount tantalum capacitors from two different capacitor manufacturers. It is recommended that both the manufacturers and the manufacturer's series that are listed in the table be used. A table listing the manufacturers' phone numbers is located in Figure 11. Surface Mount: 68 F/10V Sprague 594D Series. 100 F/10V AVX TPS Series. Through Hole: 68 F/10V Sanyo OS-CON SA Series. 150 F/35V Sanyo MV-GX Series. 150 F/35V Nichicon PL Series. 150 F/35V Panasonic HFQ Series. 3. Catch Diode Selection (D1) 3. Catch Diode Selection (D1) A. In normal operation, the average current of the catch diode is A. Refer to the table shown in Figure 12. In this example, a 1A, the load current times the catch diode duty cycle, 1-D (D is the 20V Schottky diode will provide the best performance. If the circuit switch duty cycle, which is approximately the output voltage divided must withstand a continuous shorted output, a higher current by the input voltage). The largest value of the catch diode average Schottky diode is recommended. current occurs at the maximum load current and maximum input voltage (minimum D). For normal operation, the catch diode current rating must be at least 1.3 times greater than its maximum average current. However, if the power supply design must withstand a continuous output short, the diode should have a current rating equal to the maximum current limit of the LM2671. The most stressful condition for this diode is a shorted output condition. B. The reverse voltage rating of the diode should be at least 1.25 times the maximum input voltage. C. Because of their fast switching speed and low forward voltage drop, Schottky diodes provide the best performance and efficiency. This Schottky diode must be located close to the LM2671 using short leads and short printed circuit traces. 4. Input Capacitor (CIN) 4. Input Capacitor (CIN) A low ESR aluminum or tantalum bypass capacitor is needed The important parameters for the input capacitor are the input between the input pin and ground to prevent large voltage voltage rating and the RMS current rating. With a maximum input transients from appearing at the input. This capacitor should be voltage of 12V, an aluminum electrolytic capacitor with a voltage located close to the IC using short leads. In addition, the RMS rating greater than 15V (1.25 x VIN) would be needed. The next current rating of the input capacitor should be selected to be at least higher capacitor voltage rating is 16V. 1/2 the DC load current. The capacitor manufacturer data sheet must The RMS current rating requirement for the input capacitor in a be checked to assure that this current rating is not exceeded. The buck regulator is approximately 1/2 the DC load current. In this curves shown in Figure 14 show typical RMS current ratings for example, with a 500 mA load, a capacitor with a RMS current rating several different aluminum electrolytic capacitor values. A parallel of at least 250 mA is needed. The curves shown in Figure 14 can connection of two or more capacitors may be required to increase be used to select an appropriate input capacitor. From the curves, the total minimum RMS current rating to suit the application locate the 16V line and note which capacitor values have RMS requirements. current ratings greater than 250 mA. For an aluminum electrolytic capacitor, the voltage rating should be For a through hole design, a 100 F/16V electrolytic capacitor at least 1.25 times the maximum input voltage. Caution must be (Panasonic HFQ series, Nichicon PL, Sanyo MV-GX series or exercised if solid tantalum capacitors are used. The tantalum equivalent) would be adequate. Other types or other capacitor voltage rating should be twice the maximum input manufacturers' capacitors can be used provided the RMS ripple voltage. The tables in Figure 15 show the recommended current ratings are adequate. Additionally, for a complete surface application voltage for AVX TPS and Sprague 594D tantalum mount design, electrolytic capacitors such as the Sanyo CV-C or capacitors. It is also recommended that they be surge current CV-BS and the Nichicon WF or UR and the NIC Components NACZ tested by the manufacturer. The TPS series available from AVX, series could be considered. and the 593D and 594D series from Sprague are all surge current For surface mount designs, solid tantalum capacitors can be used, tested. Another approach to minimize the surge current stresses but caution must be exercised with regard to the capacitor surge on the input capacitor is to add a small inductor in series with the current rating and voltage rating. In this example, checking Figure input supply line. 15, and the Sprague 594D series datasheet, a Sprague 594D 15 Use caution when using ceramic capacitors for input bypassing, F, 25V capacitor is adequate. because it may cause severe ringing at the VIN pin. Copyright (c) 1999-2012, Texas Instruments Incorporated 13 LM2671 PROCEDURE (Fixed Output Voltage Version) 5. Boost Capacitor (CB) This capacitor develops the necessary voltage to turn the switch gate on fully. All applications should use a 0.01 F, 50V ceramic capacitor. 6. Soft-Start Capacitor (CSS - optional) This capacitor controls the rate at which the device starts up. The formula for the soft-start capacitor CSS is: EXAMPLE (Fixed Output Voltage Version) 5. Boost Capacitor (CB) For this application, and all applications, use a 0.01 F, 50V ceramic capacitor. 6. Soft-Start Capacitor (CSS - optional) For this application, selecting a start-up time of 10 ms and using the formula for CSS results in a value of: where: ISS = Soft-Start Current :4.5 A typical. tSS = Soft-Start Time :Selected. VSSTH = Soft-Start Threshold Voltage :0.63V typical. VOUT = Output Voltage :Selected. VSCHOTTKY = Schottky Diode Voltage Drop :0.4V typical. VIN = Input Voltage :Selected. If this feature is not desired, leave this pin open. With certain softstart capacitor values and operating conditions, the LM2671 can exhibit an overshoot on the output voltage during turn on. Especially when starting up into no load or low load, the softstart function may not be effective in preventing a larger voltage overshoot on the output. With larger loads or lower input voltages during startup this effect is minimized. In particular, avoid using softstart capacitors between 0.033F and 1F. 7. Frequency Synchronization (optional) 7. Frequency Synchronization (optional) The LM2671 (oscillator) can be synchronized to run with an For all applications, use a 1 k resistor and a 100 pF capacitor for external oscillator, using the sync pin (pin 3). By doing so, the the RC filter. LM2671 can be operated at higher frequencies than the standard frequency of 260 kHz. This allows for a reduction in the size of the inductor and output capacitor. As shown in the drawing below, a signal applied to a RC filter at the sync pin causes the device to synchronize to the frequency of that signal. For a signal with a peak-to-peak amplitude of 3V or greater, a 1 k resistor and a 100 pF capacitor are suitable values. 14 Copyright (c) 1999-2012, Texas Instruments Incorporated LM2671 INDUCTOR VALUE SELECTION GUIDES (For Continuous Mode Operation) 10004229 FIGURE 4. LM2671-3.3 10004230 FIGURE 5. LM2671-5.0 10004231 FIGURE 6. LM2671-12 Copyright (c) 1999-2012, Texas Instruments Incorporated 15 LM2671 10004232 FIGURE 7. LM2671-ADJ Ind. Inducta nce Ref. Desg. (H) Current (A) Schott Through Hole Renco Surface Mount Through Hole Pulse Engineering Surface Mount Through Hole Surface Mount Coilcraft Surface Mount L2 150 0.21 67143920 67144290 RL-5470-4 RL1500-150 PE-53802 PE-53802-S DO1608-154 L3 100 0.26 67143930 67144300 RL-5470-5 RL1500-100 PE-53803 PE-53803-S DO1608-104 L4 68 0.32 67143940 67144310 RL-1284-68-43 RL1500-68 PE-53804 PE-53804-S DO1608-683 L5 47 0.37 67148310 67148420 RL-1284-47-43 RL1500-47 PE-53805 PE-53805-S DO1608-473 L6 33 0.44 67148320 67148430 RL-1284-33-43 RL1500-33 PE-53806 PE-53806-S DO1608-333 L7 22 0.52 67148330 67148440 RL-1284-22-43 RL1500-22 PE-53807 PE-53807-S DO1608-223 L9 220 0.32 67143960 67144330 RL-5470-3 RL1500-220 PE-53809 PE-53809-S DO3308-224 L10 150 0.39 67143970 67144340 RL-5470-4 RL1500-150 PE-53810 PE-53810-S DO3308-154 L11 100 0.48 67143980 67144350 RL-5470-5 RL1500-100 PE-53811 PE-53811-S DO3308-104 L12 68 0.58 67143990 67144360 RL-5470-6 RL1500-68 PE-53812 PE-53812-S DO3308-683 L13 47 0.70 67144000 67144380 RL-5470-7 RL1500-47 PE-53813 PE-53813-S DO3308-473 L14 33 0.83 67148340 67148450 RL-1284-33-43 RL1500-33 PE-53814 PE-53814-S DO3308-333 L15 22 0.99 67148350 67148460 RL-1284-22-43 RL1500-22 PE-53815 PE-53815-S DO3308-223 L18 220 0.55 67144040 67144420 RL-5471-2 RL1500-220 PE-53818 PE-53818-S DO3316-224 L19 150 0.66 67144050 67144430 RL-5471-3 RL1500-150 PE-53819 PE-53819-S DO3316-154 L20 100 0.82 67144060 67144440 RL-5471-4 RL1500-100 PE-53820 PE-53820-S DO3316-104 L21 68 0.99 67144070 67144450 RL-5471-5 RL1500-68 PE-53821 PE-53821-S DO3316-683 FIGURE 8. Inductor Manufacturers' Part Numbers Phone (800) 322-2645 FAX (708) 639-1469 Phone +44 1236 730 595 FAX +44 1236 730 627 Phone (619) 674-8100 FAX (619) 674-8262 Pulse Engineering Inc., Phone +353 93 24 107 Europe FAX +353 93 24 459 Renco Electronics Inc. Phone (800) 645-5828 FAX (516) 586-5562 Phone (612) 475-1173 FAX (612) 475-1786 Coilcraft Inc. Coilcraft Inc., Europe Pulse Engineering Inc. Schott Corp. 16 Copyright (c) 1999-2012, Texas Instruments Incorporated LM2671 FIGURE 9. Inductor Manufacturers' Phone Numbers Output Capacitor Output Voltage (V) 3.3 5.0 12 Inductance (H) Surface Mount Sprague 594D Series Through Hole AVX TPS Series Sanyo OS-CON SA Series Sanyo MV-GX Series Nichicon PL Series Panasonic HFQ Series (F/V) (F/V) (F/V) (F/V) (F/V) (F/V) 22 120/6.3 100/10 100/10 330/35 330/35 330/35 33 120/6.3 100/10 68/10 220/35 220/35 220/35 47 68/10 100/10 68/10 150/35 150/35 150/35 68 120/6.3 100/10 100/10 120/35 120/35 120/35 100 120/6.3 100/10 100/10 120/35 120/35 120/35 150 120/6.3 100/10 100/10 120/35 120/35 120/35 22 100/16 100/10 100/10 330/35 330/35 330/35 33 68/10 10010 68/10 220/35 220/35 220/35 47 68/10 100/10 68/10 150/35 150/35 150/35 68 100/16 100/10 100/10 120/35 120/35 120/35 100 100/16 100/10 100/10 120/35 120/35 120/35 150 100/16 100/10 100/10 120/35 120/35 120/35 22 120/20 (2x) 68/20 68/20 330/35 330/35 330/35 33 68/25 68/20 68/20 220/35 220/35 220/35 47 47/20 68/20 47/20 150/35 150/35 150/35 68 47/20 68/20 47/20 120/35 120/35 120/35 100 47/20 68/20 47/20 120/35 120/35 120/35 150 47/20 68/20 47/20 120/35 120/35 120/35 220 47/20 68/20 47/20 120/35 120/35 120/35 FIGURE 10. Output Capacitor Table Nichicon Corp. Panasonic AVX Corp. Sprague/Vishay Sanyo Corp. Phone (847) 843-7500 FAX (847) 843-2798 Phone (714) 373-7857 FAX (714) 373-7102 Phone (845) 448-9411 FAX (845) 448-1943 Phone (207) 324-4140 FAX (207) 324-7223 Phone (619) 661-6322 FAX (619) 661-1055 FIGURE 11. Capacitor Manufacturers' Phone Numbers 1A Diodes 3A Diodes VR Surface Mount Through Hole Surface Mount Through Hole 20V SK12 1N5817 SK32 1N5820 B120 SR102 Copyright (c) 1999-2012, Texas Instruments Incorporated SR302 17 LM2671 1A Diodes 3A Diodes VR Surface Mount 30V SK13 1N5818 SK33 1N5821 B130 11DQ03 30WQ03F 31DQ03 MBRS130 SR103 40V Through Hole Surface Mount Through Hole SK14 1N5819 SK34 1N5822 B140 11DQ04 30BQ040 MBR340 MBRS140 SR104 30WQ04F 31DQ04 10BQ040 MBRS340 SR304 10MQ040 MBRD340 15MQ040 50V SK15 MBR150 SK35 MBR350 B150 11DQ05 30WQ05F 31DQ05 10BQ050 SR105 SR305 FIGURE 12. Schottky Diode Selection Table International Rectifier Corp. Motorola, Inc. General Instruments Corp. Diodes, Inc. Phone (310) 322-3331 FAX (310) 322-3332 Phone (800) 521-6274 FAX (602) 244-6609 Phone (516) 847-3000 FAX (516) 847-3236 Phone (805) 446-4800 FAX (805) 446-4850 FIGURE 13. Diode Manufacturers' Phone Numbers 10004233 FIGURE 14. RMS Current Ratings for Low ESR Electrolytic Capacitors (Typical) 18 Copyright (c) 1999-2012, Texas Instruments Incorporated LM2671 AVX TPS Recommended Application Voltage Voltage Rating +85C Rating 3.3 6.3 5 10 10 20 12 25 15 35 Sprague 594D Recommended Application Voltage Voltage Rating +85C Rating 2.5 4 3.3 6.3 5 10 8 16 12 20 18 25 24 35 29 50 FIGURE 15. Recommended Application Voltage for AVX TPS and Sprague 594D Tantalum Chip Capacitors Derated for 85C. LM2671 Series Buck Regulator Design Procedure (Adjustable Output) PROCEDURE (Adjustable Output Voltage Version) EXAMPLE (Adjustable Output Voltage Version) To simplify the buck regulator design procedure, National Semiconductor is making available computer design software to be used with the SIMPLE SWITCHER line of switching regulators. LM267X Made Simple is available on (version 6.0) Windows 3.1, NT, or 95 operating systems. Given: Given: VOUT = Regulated Output Voltage VOUT = 20V VIN(max) = Maximum Input Voltage VIN(max) = 28V ILOAD(max) = Maximum Load Current ILOAD(max) = 500 mA F = Switching Frequency (Fixed at a nominal 260 kHz). F = Switching Frequency (Fixed at a nominal 260 kHz). 1. Programming Output Voltage (Selecting R1 and R2, as shown 1. Programming Output Voltage (Selecting R1 and R2, as shown in Figure 3) in Figure 3) Use the following formula to select the appropriate resistor values. Select R1 to be 1 k, 1%. Solve for R2. where VREF = 1.21V Select a value for R1 between 240 and 1.5 k. The lower resistor R2 = 1 k (16.53 - 1) = 15.53 k, closest 1% value is 15.4 k. values minimize noise pickup in the sensitive feedback pin. (For the R2 = 15.4 k. lowest temperature coefficient and the best stability with time, use 1% metal film resistors.) 2. Inductor Selection (L1) A. Calculate the inductor Volt * microsecond constant E * T (V * s), from the following formula: Copyright (c) 1999-2012, Texas Instruments Incorporated 2. Inductor Selection (L1) A. Calculate the inductor Volt * microsecond constant (E * T), 19 LM2671 PROCEDURE (Adjustable Output Voltage Version) EXAMPLE (Adjustable Output Voltage Version) where VSAT=internal switch saturation voltage=0.25V and VD = diode forward voltage drop = 0.5V B. Use the E * T value from the previous formula and match it with B. E * T = 21.6 (V * s) the E * T number on the vertical axis of the Inductor Value Selection Guide shown in Figure 7. C. On the horizontal axis, select the maximum load current. C. ILOAD(max) = 500 mA D. Identify the inductance region intersected by the E * T value and D. From the inductor value selection guide shown in Figure 7, the the Maximum Load Current value. Each region is identified by an inductance region intersected by the 21.6 (V * s) horizontal line inductance value and an inductor code (LXX). and the 500 mA vertical line is 100 H, and the inductor code is L20. E. Select an appropriate inductor from the four manufacturer's part E. From the table in Figure 8, locate line L20, and select an inductor numbers listed in Figure 8. For information on the different types of part number from the list of manufacturers' part numbers. inductors, see the inductor selection in the fixed output voltage design procedure. 3. Output Capacitor SeIection (COUT) 3. Output Capacitor SeIection (COUT) A. Select an output capacitor from the capacitor code selection A. Use the appropriate row of the capacitor code selection guide, guide in Figure 16. Using the inductance value found in the inductor in Figure 16. For this example, use the 15-20V row. The capacitor selection guide, step 1, locate the appropriate capacitor code code corresponding to an inductance of 100 H is C20. corresponding to the desired output voltage. B. Select an appropriate capacitor value and voltage rating, using B. From the output capacitor selection table in Figure 17, choose the capacitor code, from the output capacitor selection table in a capacitor value (and voltage rating) that intersects the capacitor Figure 17. There are two solid tantalum (surface mount) capacitor code(s) selected in section A, C20. manufacturers and four electrolytic (through hole) capacitor The capacitance and voltage rating values corresponding to the manufacturers to choose from. It is recommended that both the capacitor code C20 are the: manufacturers and the manufacturer's series that are listed in the Surface Mount: table be used. A table listing the manufacturers' phone numbers is 33 F/25V Sprague 594D Series. located in Figure 11. 33 F/25V AVX TPS Series. Through Hole: 33 F/25V Sanyo OS-CON SC Series. 120 F/35V Sanyo MV-GX Series. 120 F/35V Nichicon PL Series. 120 F/35V Panasonic HFQ Series. Other manufacturers or other types of capacitors may also be used, provided the capacitor specifications (especially the 100 kHz ESR) closely match the characteristics of the capacitors listed in the output capacitor table. Refer to the capacitor manufacturers' data sheet for this information. 4. Catch Diode Selection (D1) 4. Catch Diode Selection (D1) A. In normal operation, the average current of the catch diode is A. Refer to the table shown in Figure 12. Schottky diodes provide the load current times the catch diode duty cycle, 1-D (D is the the best performance, and in this example a 1A, 40V Schottky diode switch duty cycle, which is approximately VOUT/VIN). The largest would be a good choice. If the circuit must withstand a continuous value of the catch diode average current occurs at the maximum shorted output, a higher current (at least 1.2A) Schottky diode is input voltage (minimum D). For normal operation, the catch diode recommended. current rating must be at least 1.3 times greater than its maximum average current. However, if the power supply design must withstand a continuous output short, the diode should have a current rating greater than the maximum current limit of the LM2671. The most stressful condition for this diode is a shorted output condition. B. The reverse voltage rating of the diode should be at least 1.25 times the maximum input voltage. 20 Copyright (c) 1999-2012, Texas Instruments Incorporated LM2671 PROCEDURE (Adjustable Output Voltage Version) C. Because of their fast switching speed and low forward voltage drop, Schottky diodes provide the best performance and efficiency. The Schottky diode must be located close to the LM2671 using short leads and short printed circuit traces. 5. Input Capacitor (CIN) A low ESR aluminum or tantalum bypass capacitor is needed between the input pin and ground to prevent large voltage transients from appearing at the input. This capacitor should be located close to the IC using short leads. In addition, the RMS current rating of the input capacitor should be selected to be at least 1/2 the DC load current. The capacitor manufacturer data sheet must be checked to assure that this current rating is not exceeded. The curves shown in Figure 14 show typical RMS current ratings for several different aluminum electrolytic capacitor values. A parallel connection of two or more capacitors may be required to increase the total minimum RMS current rating to suit the application requirements. For an aluminum electrolytic capacitor, the voltage rating should be at least 1.25 times the maximum input voltage. Caution must be exercised if solid tantalum capacitors are used. The tantalum capacitor voltage rating should be twice the maximum input voltage. The tables in Figure 15 show the recommended application voltage for AVX TPS and Sprague 594D tantalum capacitors. It is also recommended that they be surge current tested by the manufacturer. The TPS series available from AVX, and the 593D and 594D series from Sprague are all surge current tested. Another approach to minimize the surge current stresses on the input capacitor is to add a small inductor in series with the input supply line. Use caution when using ceramic capacitors for input bypassing, because it may cause severe ringing at the VIN pin. EXAMPLE (Adjustable Output Voltage Version) 5. Input Capacitor (CIN) The important parameters for the input capacitor are the input voltage rating and the RMS current rating. With a maximum input voltage of 28V, an aluminum electrolytic capacitor with a voltage rating of at least 35V (1.25 x VIN) would be needed. The RMS current rating requirement for the input capacitor in a buck regulator is approximately 1/2 the DC load current. In this example, with a 500 mA load, a capacitor with a RMS current rating of at least 250 mA is needed. The curves shown in Figure 14 can be used to select an appropriate input capacitor. From the curves, locate the 35V line and note which capacitor values have RMS current ratings greater than 250 mA. For a through hole design, a 68 F/35V electrolytic capacitor (Panasonic HFQ series, Nichicon PL, Sanyo MV-GX series or equivalent) would be adequate. Other types or other manufacturers' capacitors can be used provided the RMS ripple current ratings are adequate. Additionally, for a complete surface mount design, electrolytic capacitors such as the Sanyo CV-C or CV-BS and the Nichicon WF or UR and the NIC Components NACZ series could be considered. For surface mount designs, solid tantalum capacitors can be used, but caution must be exercised with regard to the capacitor surge current rating and voltage rating. In this example, checking Figure 15, and the Sprague 594D series datasheet, a Sprague 594D 15 F, 50V capacitor is adequate. 6. Boost Capacitor (CB) 6. Boost Capacitor (CB) This capacitor develops the necessary voltage to turn the switch For this application, and all applications, use a 0.01 F, 50V gate on fully. All applications should use a 0.01 F, 50V ceramic ceramic capacitor. capacitor. If the soft-start and frequency synchronization features are desired, look at steps 6 and 7 in the fixed output design procedure. Inductance (H) Case Style (Note 7) Output Voltage (V) 22 33 47 68 100 150 220 SM and TH 1.21-2.50 -- -- -- -- C1 C2 C3 SM and TH 2.50-3.75 -- -- -- C1 C2 C3 C3 SM and TH 3.75-5.0 -- -- C4 C5 C6 C6 C6 SM and TH 5.0-6.25 -- C4 C7 C6 C6 C6 C6 SM and TH 6.25-7.5 C8 C4 C7 C6 C6 C6 C6 SM and TH 7.5-10.0 C9 C10 C11 C12 C13 C13 C13 SM and TH 10.0-12.5 C14 C11 C12 C12 C13 C13 C13 SM and TH 12.5-15.0 C15 C16 C17 C17 C17 C17 C17 SM and TH 15.0-20.0 C18 C19 C20 C20 C20 C20 C20 SM and TH 20.0-30.0 C21 C22 C22 C22 C22 C22 C22 TH 30.0-37.0 C23 C24 C24 C25 C25 C25 C25 Note 7: SM - Surface Mount, TH - Through Hole FIGURE 16. Capacitor Code Selection Guide Copyright (c) 1999-2012, Texas Instruments Incorporated 21 LM2671 Output Capacitor Surface Mount Through Hole Cap. Ref. Desg. # Sprague 594D Series (F/V) (F/V) (F/V) (F/V) (F/V) (F/V) C1 120/6.3 100/10 100/10 220/35 220/35 220/35 C2 120/6.3 100/10 100/10 150/35 150/35 150/35 C3 120/6.3 100/10 100/35 120/35 120/35 120/35 C4 68/10 100/10 68/10 220/35 220/35 220/35 C5 100/16 100/10 100/10 150/35 150/35 150/35 C6 100/16 100/10 100/10 120/35 120/35 120/35 C7 68/10 100/10 68/10 150/35 150/35 150/35 C8 100/16 100/10 100/10 330/35 330/35 330/35 C9 100/16 100/16 100/16 330/35 330/35 330/35 C10 100/16 100/16 68/16 220/35 220/35 220/35 C11 100/16 100/16 68/16 150/35 150/35 150/35 C12 100/16 100/16 68/16 120/35 120/35 120/35 C13 100/16 100/16 100/16 120/35 120/35 120/35 C14 100/16 100/16 100/16 220/35 220/35 220/35 C15 47/20 68/20 47/20 220/35 220/35 220/35 C16 47/20 68/20 47/20 150/35 150/35 150/35 C17 47/20 68/20 47/20 120/35 120/35 120/35 C18 68/25 (2x) 33/25 47/25 (Note 8) 220/35 220/35 220/35 C19 33/25 33/25 33/25 (Note 8) 150/35 150/35 150/35 C20 33/25 33/25 33/25 (Note 8) 120/35 120/35 120/35 C21 33/35 (2x) 22/25 (Note 9) 150/35 150/35 150/35 C22 33/35 22/35 (Note 9) 120/35 120/35 120/35 C23 (Note 9) (Note 9) (Note 9) 220/50 100/50 120/50 C24 (Note 9) (Note 9) (Note 9) 150/50 100/50 120/50 C25 (Note 9) (Note 9) (Note 9) 150/50 82/50 82/50 AVX TPS Series Sanyo OS-CON SA Series Sanyo MV-GX Series Nichicon PL Series Panasonic HFQ Series Note 8: The SC series of Os-Con capacitors (others are SA series) Note 9: The voltage ratings of the surface mount tantalum chip and Os-Con capacitors are too low to work at these voltages. FIGURE 17. Output Capacitor Selection Table 22 Copyright (c) 1999-2012, Texas Instruments Incorporated LM2671 Application Information TYPICAL SURFACE MOUNT PC BOARD LAYOUT, FIXED OUTPUT (4X SIZE) 10004239 CIN - 15 F, 25V, Solid Tantalum Sprague, "594D series" COUT - 68 F, 10V, Solid Tantalum Sprague, "594D series" D1 - 1A, 40V Schottky Rectifier, Surface Mount L1 - 47 H, L13, Coilcraft DO3308 CB - 0.01 F, 50V, Ceramic TYPICAL SURFACE MOUNT PC BOARD LAYOUT, ADJUSTABLE OUTPUT (4X SIZE) 10004240 CIN - 15 F, 50V, Solid Tantalum Sprague, "594D series" COUT - 33 F, 25V, Solid Tantalum Sprague, "594D series" D1 - 1A, 40V Schottky Rectifier, Surface Mount L1 - 100 H, L20, Coilcraft DO3316 CB - 0.01 F, 50V, Ceramic R1 - 1k, 1% R2 - Use formula in Design Procedure FIGURE 18. PC Board Layout Layout is very important in switching regulator designs. Rapidly switching currents associated with wiring inductance can generate voltage transients which can cause problems. For minimal inductance and ground loops, the wires indicated by heavy lines (in Figure 2 and Figure 3) should be wide printed circuit traces and should be kept as short as possible. For best results, external components should be located as close to the switcher IC as possible using ground plane construction or single point grounding. If open core inductors are used, special care must be taken as to the location and positioning of this type of inductor. Allowing the inductor flux to intersect sensitive feedback, IC ground path, and COUT wiring can cause problems. When using the adjustable version, special care must be taken as to the location of the feedback resistors and the associated wiring. Physically locate both resistors near the IC, and route the wiring away from the inductor, especially an open core type of inductor. Copyright (c) 1999-2012, Texas Instruments Incorporated 23 LM2671 24 Copyright (c) 1999-2012, Texas Instruments Incorporated LM2671 Physical Dimensions inches (millimeters) unless otherwise noted 8-Lead (0.150 Wide) Molded Small Outline Package, JEDEC Order Number LM2671M-3.3, LM2671M-5.0, LM2671M-12 or LM2671M-ADJ NS Package Number M08A Copyright (c) 1999-2012, Texas Instruments Incorporated 25 LM2671 8-Lead (0.300 Wide) Molded Dual-In-Line Package Order Number LM2671N-3.3, LM2671N-5.0, LM2671N-12 or LM2671N-ADJ NS Package Number N08E 26 Copyright (c) 1999-2012, Texas Instruments Incorporated LM2671 16-Lead LLP Surface Mount Package NS Package Number LDA16A Copyright (c) 1999-2012, Texas Instruments Incorporated 27 Notes Copyright (c) 1999-2012, Texas Instruments Incorporated IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated