CAT93C56, CAT93C57
© 2008 SCILLC. All rights reserved 1 Doc. No. MD-1088. Rev. R
Characteristics subject to change without notice
2-Kb Microwire Serial CMOS EEPROM
FEATURES
High speed operation: 2MHz
1.8V to 5.5V supply voltage range
Selectable x8 or x16 memory organization
Sequential read
Software write protection
Power-up inadvertant write protection
Low power CMOS technology
1,000,000 Program/erase cycles
100 year data retention
Industrial and Extended temperature r anges
RoHS-compliant 8-pin PDIP, SOIC, TSSOP and
8-pad TDFN packages
PIN CONFIGURATION
PDIP (L)
SOIC (V, X)
TSSOP (Y)
TDFN (VP2, ZD4*)
CS 1 8 VCC
SK 2 7 NC
DI 3 6 ORG
DO 4
5 GND
SOIC (W*)
NC 1 8 ORG
VCC 2 7 GND
CS 3 6 DO
SK 4
5DI
* TDFN 3x3mm (ZD4) and SOIC (W) rotated pin-out packages are
available for CAT93C57 and CAT93C56, Rev. E only (not
recommended for new designs of CAT93C56)
PIN FUNCTION
Pin Name Function
CS Chip Select
SK Clock Input
DI Serial Data Input
DO Serial Data Output
VCC Power Supply
GND Ground
ORG Memory Organization
NC No Connection
DESCRIPTION
The CAT93C56/57 is a 2-Kb CMOS Serial EEPROM
device which is organized as either 128 registers of 16
bits (ORG pin at VCC) or 256 registers of 8 bits (ORG pin
at GND). Each register can be written (or read) serially
by using the DI (or DO) pin. The CAT93C56/57 features
sequential read and self-timed internal write with auto-
clear. On-chip Power-On Reset circuitry protects the
internal logic against powering up in the wrong state.
For Ordering Information details, see page 16.
FUNCTIONAL SYMBOL
CS
SK
DI
ORG
DO
CAT93C56
CAT93C57
V
CC
GND
Note: When the ORG pin is connected to VCC, the x16 organization
is selected. When it is connected to ground, the x8 pin is selected. If
the ORG pin is left unconnected, then am internal pullup device will
select the x16 organization
CAT93C56, CAT93C57
Doc. No. MD-1088, Rev. R 2 © 2008 SCILLC. All rights reserved
Characteristics subject to change without notice
Absolute Maximum Ratings(1)
Parameters Ratings Units
Storage Temperature -65 to +150 °C
Voltage on Any Pin with Respect to Ground(2) -0.5 to +6.5 V
Reliability Characteristics(3)
Symbol Parameter Min Units
NEND(4) Endurance 1,000,000 Program/ Erase Cycles
TDR Data Retention 100 Years
D.C. OPERATING CHARACTERISTICS, CAT93C56, Die Rev. G – New Product
VCC = +1.8V to +5.5V, TA=-40°C to +125°C unless otherwise spe cified.
Symbol Parameter Test Conditions Min Max Units
ICC1 Power Supply Current
(Write) fSK = 1MHz, VCC = 5.0V 1 mA
ICC2 Power Supply Current
(Read) fSK = 1MHz, VCC = 5.0V 500 µA
TA = -40°C to +85°C 2
ISB1 Power Supply Current
(Standby) (x8 Mode) VIN = GND or VCC,
CS = GND ORG = GND TA = -40°C to +125°C 4
µA
TA = -40°C to +85°C 1
ISB2 Power Supply Current
(Standby) (x16 Mode) VIN = GND or VCC, CS =
GND ORG = Float or VCC TA = -40°C to +125°C 2
µA
TA = -40°C to +85°C 1
ILI Input Leakage Current VIN = GND to VCC TA = -40°C to +125°C 2
µA
TA = -40°C to +85°C 1
ILO Output Leakage
Current VOUT = GND to VCC,
CS = GND TA = -40°C to +125°C 2
µA
VIL1 Input Low Voltage 4.5V ≤ VCC < 5.5V -0.1 0.8 V
VIH1 Input High Voltage 4.5V ≤ VCC < 5.5V 2 VCC + 1 V
VIL2 Input Low Voltage 1.8V ≤ VCC < 4.5V 0 VCC x 0.2 V
VIH2 Input High Voltage 1.8V ≤ VCC < 4.5V VCC x 0.7 VCC + 1 V
VOL1 Output Low Voltage 4.5V ≤ VCC < 5.5V,
IOL = 2.1mA 0.4 V
VOH1 Output High Voltage 4.5V ≤ VCC < 5.5V,
IOH = -400µA 2.4 V
VOL2 Output Low Voltage 1.8V ≤ VCC < 4.5V,
IOL = 1mA 0.2 V
VOH2 Output High Voltage 1.8V ≤ VCC < 4.5V,
IOH = -100µA VCC - 0.2 V
Notes:
(1) Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions outside of those listed in the operational sections of this
specification is not implied. Exposure to any absolute maximum rating for extended periods may affect device performance and reliability.
(2) The D C input voltage on any pin should not be lower th an -0.5V or higher than VCC + 0.5V. During transitions, the voltage on an y pin may
undershoot to no less than -1.5V or overshoot to no more than VCC + 1.5V, for periods of less than 20 ns.
(3) These paramete rs are tested initially and after a design or process change that affects the parameter according to appropriate AEC-Q100
and JEDEC test methods.
(4) Block Mode, VCC = 5V, 25°C
CAT93C56, CAT93C57
© 2008 SCILLC. All rights reserved 3 Doc. No. MD-1088, Rev. R
Characteristics subject to change without notice
D.C. OPERATING CHARACTERISTICS, CAT93C56/57, Die Rev. E – Mature Product
(CAT93C56, Rev . E – NOT RECOMMENDED FOR NEW DESIGNS)
VCC = +1.8V to +5.5V, TA=-40°C to +125°C unless otherwise spe cified.
Symbol Parameter Test Conditions Min Max Units
ICC1 Power Supply Current (Write) fSK = 1MHz, VCC = 5.0V 3 mA
ICC2 Power Supply Current (Read) fSK = 1MHz, VCC = 5.0V 500 µA
ISB1 Power Supply Current
(Standby) (x8 Mode) VIN = GND or VCC, CS = GND
ORG = GND 10 µA
ISB2 Power Supply Current
(Standby) (x16 Mode) VIN = GND or VCC, CS = GND
ORG = Float or VCC 10 µA
ILI Input Leakage Current VIN = GND to VCC 1 µA
ILO Output Leakage Current VOUT = GND to VCC, CS = GND 1 µA
VIL1 Input Low Voltage 4.5V ≤ VCC < 5.5V -0.1 0.8 V
VIH1 Input High Voltage 4.5V ≤ VCC < 5.5V 2 V CC + 1 V
VIL2 Input Low Voltage 1.8V ≤ VCC < 4.5V 0 VCC x 0.2 V
VIH2 Input High Voltage 1.8V ≤ VCC < 4.5V VCC x 0.7 VCC + 1 V
VOL1 Output Low Voltage 4.5V ≤ VCC < 5.5V, IOL = 2.1mA 0.4 V
VOH1 Output High Voltage 4.5V ≤ VCC < 5.5V, IOH = -400µA 2.4 V
VOL2 Output Low Voltage 1.8V ≤ VCC < 4.5V, IOL = 1mA 0.2 V
VOH2 Output High Voltage 1.8V ≤ VCC < 4.5V, IOH = -100µA VCC - 0.2 V
PIN CAPACITANCE
TA = 25°C, f = 1MHz, VCC = 5V
Symbol Test Conditions Min Typ Max Units
COUT(1) Output Capacitance (DO) VOUT = 0V 5 pF
CIN(1) Input Capacitance (CS, SK, DI, ORG) VIN = 0V 5 pF
Notes:
(1) These paramete rs are tested initially and after a design or process change that affects the parameter according to appropriate AEC-Q100
and JEDEC test methods.
CAT93C56, CAT93C57
Doc. No. MD-1088, Rev. R 4 © 2008 SCILLC. All rights reserved
Characteristics subject to change without notice
A.C. CHARACTERISTICS(1), CAT93C56, Die Rev. G – New Product
VCC = +1.8V to +5.5V, TA = -40°C to +125°C, unless otherwise specified.
Limits
Symbol Parameter Min Max
Units
tCSS CS Setup Time 50 ns
tCSH CS Hold Time 0 ns
tDIS DI Setup Time 100 ns
tDIH DI Hold Time 100 ns
tPD1 Output Delay to 1 0.25 µs
tPD0 Output Delay to 0 0.25 µs
tHZ(2) Output Delay to High-Z 100 ns
tEW Program/Erase Pulse Width 5 ms
tCSMIN Minimum CS Low Time 0.25 µs
tSKHI Minimum SK High Time 0.25 µs
tSKLOW Minimum SK Low Time 0.25 µs
tSV Output Delay to Status Valid 0.25 µs
SKMAX Maximum Clock Frequency DC 2000 kHz
A.C. CHARACTERISTICS (1), CAT93C56/57, Die Rev. E – Matur e Product
(CAT93C56 Rev. E - NOT RECOMMENDED FOR NEW DESIGNS)
Limits
VCC = 1.8V - 5.5V VCC = 2.5V - 5.5V VCC = 4.5V - 5.5V
Symbol Parameter Min Max Min Max Min Max Units
tCSS CS Setup Time 200 100 50 ns
tCSH CS Hold Time 0 0 0 ns
tDIS DI Setup Time 400 200 100 ns
tDIH DI Hold Time 400 200 100 ns
tPD1 Output Delay to 1 1 0.5 0.25 µs
tPD0 Output Delay to 0 1 0.5 0.25 µs
tHZ(2) Output Delay to High-Z 400 200 100 ns
tEW Program/Erase Pulse Width 10 10 10 ms
tCSMIN Minimum CS Low Time 1 0.5 0.25 µs
tSKHI Minimum SK High Time 1 0.5 0.25 µs
tSKLOW Minimum SK Low Time 1 0.5 0.25 µs
tSV Output Delay to Status Valid 1 0.5 0.25 µs
SKMAX Maximum Clock Frequency DC 250 DC 500 DC 1000 kHz
Notes:
(1) Test conditions according to “A.C. Test Conditions” table.
(2) These parameters are tested initially and after a design or process change that affects the parameter according to appropriate
AEC-Q100 and JEDEC test methods.
CAT93C56, CAT93C57
© 2008 SCILLC. All rights reserved 5 Doc. No. MD-1088, Rev. R
Characteristics subject to change without notice
POWER-UP TIMING(1) (2)
Symbol Parameter Max Units
tPUR Power-up to Read Operation 1 ms
tPUW Power-up to Write Operation 1 ms
Notes:
(1) These parameters are tested initially and after a design or process change that affects the parameter according to appropriate
AEC-Q100 and JEDEC test methods.
(2) tPUR and tPUW are the delays required from the time VCC is stable until the specified operation can be initiated.
A.C. Test Conditions
Input Rise and Fall Times ≤ 50 ns
Input Pulse Voltages 0.4V to 2.4V 4.5V ≤ VCC ≤ 5.5V
Timing Reference Voltages 0.8V, 2.0V 4.5V ≤ VCC ≤ 5.5V
Input Pulse Voltages 0.2VCC to 0.7VCC 1.8V ≤ VCC ≤ 4.5V
Timing Reference Voltages 0.5VCC 1.8V ≤ VCC ≤ 4.5V
Output Load Current Source IOLmax/IOHmax; CL=100pF
DEVICE OPERATION
The CAT93C56/57 is a 2048-bit nonvolatile memory
intended for use with industry standard micropro-
cessors. The CAT93C56/57 can be organized as
either registers of 16 bits or 8 bits. When organized as
X16, seven 10-bit instructions for 93C57 or seven 11-
bit instructions for 93C56 control the reading, writing
and erase operations of the device. When organized
as X8, seven 11-bit instructions for 93C57 or seven
12-bit instructions for 93C56 control the reading,
writing and erase operations of the device. The
CAT93C56/57 operates on a single power supply and
will generate on chip, the high voltage required during
any write operation.
Instructions, addresses, and write data are clocked
into the DI pin on the rising edge of the clock (SK).
The DO pin is normally in a high impedance state
except when reading data from the device, or when
checking the ready/busy status after a write operation.
The serial communication protocol follows the timing
shown in Figure 1.
The ready/busy status can be determined after the start
of internal write cycle by selecting the device (CS high)
and polling the DO pin; DO low indicates that the write
operation is not completed, while DO high indicates that
the device is ready for the next instruction. If necessar y,
the DO pin may be placed back into a high impedance
state during chip select by shifting a dummy “1” into the
DI pin. The DO pin will enter the high impedance state
on the rising edge of the clock (SK). Placing the DO pin
into the high impedance state is recommended in
applications where the DI pin and the DO pin are to be
tied together to form a common DI/O pin.
Figure 1. Sychronous Data Timing
SK
DI
CS
D
O
tDIS tPD0,tPD1 tCSMIN
tCSS
tDIS tDIH
tSKHI tCSH
VALID VALID
DATA VALID
tSKLOW
CAT93C56, CAT93C57
Doc. No. MD-1088, Rev. R 6 © 2008 SCILLC. All rights reserved
Characteristics subject to change without notice
The format for all instructions sent to the device is a
logical “1” start bit, a 2-bit (or 4-bit) opcode, 7-bit
address (CAT93C57) / 8-bit address (CAT93C56) (an
additional bit when organized X8) and for write
operations a 16-bit data field (8-bit for X8 organi–
zations). The instruction format is shown in Instruction
Set table.
INSTRUCTION SET
Address Data
Instruction Device
Type Start
Bit Opcode x8 x16 x8 x16
Comments
READ 93C56(1) 1 10 A8-A0 A7-A0
93C57 1 10 A7-A0 A6-A0
Read Address
AN–A0
ERASE 93C56(1) 1 11 A8-A0 A7-A0
93C57 1 11 A7-A0 A6-A0
Clear Address
AN–A0
WRITE 93C56(1) 1 01 A8-A0 A7-A0 D7-D0 D15-D0
93C57 1 01 A7-A0 A6-A0 D7-D0 D15-D0
Write Address
AN–A0
EWEN 93C56(1) 1 00 11XXXXXXX 11XXXXXX
93C57 1 00 11XXXXXX 11XXXXX Write Enable
EWDS 93C56(1) 1 00 00XXXXXXX 00XXXXXX
93C57 1 00 00XXXXXX 00XXXXX Write Disable
ERAL 93C56(1) 1 00 10XXXXXXX 10XXXXXX
93C57 1 00 10XXXXXX 10XXXXX Clear All
Addresses
WRAL 93C56(1) 1 00 01XXXXXXX 01XXXXXX D7-D0 D15-D0
93C57 1 00 01XXXXXX 01XXXXX D7-D0 D15-D0
Write All
Addresses
Note:
(1) Address bit A8 for 256x8 organization and A7 for 128x16 organization are "Don't Care" bits, but must be kept at either a "1" or "0" for
READ, WRITE and ERASE commands.
CAT93C56, CAT93C57
© 2008 SCILLC. All rights reserved 7 Doc. No. MD-1088, Rev. R
Characteristics subject to change without notice
Read
Upon receiving a READ command and an address
(clocked into the DI pin), the DO pin of the
CAT93C56/57 will come out of the high impedance
state and, after sending an initial dummy zero bit, will
begin shifting out the data addressed (MSB first). The
output data bits will toggle on the rising edge of the
SK clock and are stable after the specified time delay
(tPD0 or tPD1).
For the CAT93C56/57, after the initial data word has
been shifted out and CS remains asserted with the SK
clock continuing to toggle, the device will auto-
matically increment to the next address and shift out
the next data word in a sequential READ mode. As
long as CS is continuously asserted and SK continues
to toggle, the device will keep incrementing to the next
address automatically until it reaches to the end of the
address space, then loops back to address 0. In the
sequential READ mode, only the initial data word is
preceeded by a dummy zero bit. All subsequent data
words will follow without a dummy zero bit. The READ
instruction timing is illustrated in Figure 2.
Erase/Write Enable and Disable
The CAT93C56/57 powers up in the write disable state.
Any writing after power-up or after an EWDS (erase/write
disable) ins truction must first be preceded by the EWEN
(erase/write enable) instruction. Once the write
instruction is enabled, it will remain enabled until power
to the device is removed, or the EWDS instruction is
sent. The EWDS instruction can be used to disable all
CAT93C56/57 write and erase instructions, and will
prevent any accidental writing or clearing of the device.
Data can be read normally from th e de vice r egard less of
the write enable/disable status. The EWEN and EWDS
instructions timing is shown in Figure 3.
Figure 2. READ Instruction Timing
Figure 3. EWEN/EWDS Instruction Timing
SK
CS
DI
DO HIGH-Z
11 0
ANAN–1 A0
Dummy 0 D15 . . .D0
or
D7 . . .D0
Address + 1
D15 . . .D0
or
D7 . . .D0
Address + 2
D15 . . .D0
or
D7 . . . D0
Address + n
D15 . . .
or
D7 . . .
Don't Ca re
t
PD0
CS
DI
STANDBY
10
0*
* ENABLE = 11
DISABLE = 00
SK
CAT93C56, CAT93C57
Doc. No. MD-1088, Rev. R 8 © 2008 SCILLC. All rights reserved
Characteristics subject to change without notice
Write
After receiving a WRITE command (Figure 4), address
and the data, the CS (Chip Select) pin must be
deselected for a minimum of tCSMIN. The falling edge of
CS will start the self clocking clear and data store cycle
of the memory location specified in the instruction. The
clocking of the SK pin is not necessary after the device
has entered the self clocking mode. The ready/busy
status of the CAT93C56/57 can be determined by
selecting the device and polling the DO pin. Since this
device features Auto-Clear before write, it is NOT
necessary to erase a memory location before it is
written into.
Erase
Upon receiving an ERASE command and address, the
CS (Chip Select) pin must be deasserted for a
minimum of tCSMIN (Figure 5). The falling edge of CS will
start the self clocking clear cycle of the selected
memory location. The clocking of the SaK pin is not
necessary after the device has entered the self clocking
mode. The ready/busy stat us of the CAT93C56/57 can
be determined by selecting the device and polling the
DO pin. Once cleared, the content of a cleared location
returns to a logical “1” state.
Figure 4. Write Instruction Timing
Figure 5. Erase Instruction Timing
SK
CS
DI
DO
tCSMIN
STANDBY
HIGH-Z
HIGH-Z
101
ANAN-1 A0DND0
BUSY
READY
STATUS
VERIFY
tSV tHZ
tEW
SK
CS
DI
DO
STANDBY
HIGH-Z
HIGH-Z
1
ANAN-1
BUSY READY
STATUS VERIFY
tSV tHZ
tEW
tCS
11
A0
CAT93C56, CAT93C57
© 2008 SCILLC. All rights reserved 9 Doc. No. MD-1088, Rev. R
Characteristics subject to change without notice
Erase All
Upon receiving an ERAL command (Figure 6), the CS
(Chip Select) pin must be deselected for a minimum of
tCSMIN. The falling edge of CS will start the self clocking
clear cycle of all memory locations in the device. The
clocking of the SK pin is not necessary after the
device has entered the self clocking mode. The
ready/busy status of the CAT93C56/57 can be deter-
mined by selecting the device and polling the DO pin.
Once cleared, the contents of all memory bits return to
a logical “1” state.
Write All
Upon receiving a WRAL command and data, the CS
(Chip Select) pin must be deselected for a minimum of
tCSMIN (Figure 7). The falling edge of CS will start the
self clocking data write to all memory locations in the
device. The clocking of the SK pin is not necessary
after the device has entered the self clocking mode.
The ready/busy status of the CAT93C56/57 can be
determined by selecting the device and polling the DO
pin. It is not necessary for all memory locations to be
cleared before the WRAL command is executed.
Figure 6. ERAL Instruction Timing
Figure 7. WRAL Instruction Timing
SK
CS
DI
DO
STANDBY
tCS
HIGH-Z
HIGH-Z
10 1
BUSY READY
STATUS VERIFY
tSV tHZ
tEW
00
STATUS VERIFY
SK
CS
DI
DO
STANDBY
HIGH-Z
10 1
BUSY READY
tSV tHZ
tEW
tCSMIN
DND0
00
CAT93C56, CAT93C57
Doc. No. MD-1088, Rev. R 10 © 2008 SCILLC. All rights reserved
Characteristics subject to change without notice
PACKAGE OUTLINE DRAWINGS
PDIP 8-Lead 300mils (L) (1)
Notes:
(1) All dimensions are in millimeters.
(2) Complies with JEDEC standard MS-001.
For current Tape and Reel information, download the PDF file from:
http://www.catsemi.com/documents/tapeandreel.pdf.
E1
D
A
L
eb
b2
A1
A2
E
eB
c
TOP VI EW
SIDE VI EW END VIEW
PIN # 1
IDENTIFICATION
SYMBOL MIN NOM MAX
A5.33
A1 0.38
A2 2.92 3.30 4.95
b 0.36 0.46 0.56
b2 1.14 1.52 1.78
c 0.20 0.25 0.36
D 9.02 9.27 10.16
E 7.62 7.87 8.25
e 2.54 BSC
E1 6.10 6.35 7.11
eB 7.87 10.92
L 2.92 3.30 3.80
CAT93C56, CAT93C57
© 2008 SCILLC. All rights reserved 11 Doc. No. MD-1088, Rev. R
Characteristics subject to change without notice
SOIC 8-Lead 150mils (V, W) (1)
Notes:
1) All dimensions are in millimeters. Angles in degrees.
(2) Complies with JEDEC standard MS-012.
For current Tape and Reel information, download the PDF file from:
http://www.catsemi.com/documents/tapeandreel.pdf.
E1 E
A
A1
h
θ
Lc
eb
D
PIN # 1
IDENTIFICATION
TOP VIEW
SIDE VIEW END VIEW
A 1.35 1.75
A1 0.10 0.25
b 0.33 0.51
c 0.19 0.25
D 4.80 5.00
E 5.80 6.20
E1 3.80 4.00
e 1.27 BSC
h 0.25 0.50
L 0.40 1.27
θ0º 8º
SYMBOL MIN NOM MAX
CAT93C56, CAT93C57
Doc. No. MD-1088, Rev. R 12 © 2008 SCILLC. All rights reserved
Characteristics subject to change without notice
SOIC 8-Lead EIAJ (208mils) (X) (1)
Notes:
(1) All dimensions are in millimeters. Angles in degrees.
(2) Complies with EIAJ EDR-7320
For current Tape and Reel information, download the PDF file from:
http://www.catsemi.com/documents/tapeandreel.pdf.
θ
E1
eb
SIDE VIEW
TOP VIEW
E
D
PIN#1 IDENTIFICATION
END VIEW
A1
A
Lc
SYMBOL MIN NOM MAX
A2.03
A1 0.05 0.25
b0.36 0.48
c0.19 0.25
D5.13 5.33
E7.75 8.26
E1 5.13 5.38
e 1.27 BSC
L0.51 0.76
θ0º 8º
CAT93C56, CAT93C57
© 2008 SCILLC. All rights reserved 13 Doc. No. MD-1088, Rev. R
Characteristics subject to change without notice
TSSOP 8-Lead 4.4mm (Y) (1)
Notes:
(1) All dimensions are in millimeters. Angles in degrees.
(2) Complies with JEDEC MO-153.
For current Tape and Reel information, download the PDF file from:
http://www.catsemi.com/documents/tapeandreel.pdf.
A2
E1 E
A1
e
b
D
c
A
TOP VIEW
SIDE VIEW END VIEW
θ1
L1 L
SYMBOL MIN NOM MAX
A1.20
A1 0.05 0.15
A2 0.80 0.90 1.05
b0.19 0.30
c0.09 0.20
D 2.90 3.00 3.10
E 6.30 6.40 6.50
E1 4.30 4.40 4.50
e 0.65 BSC
L1.00 REF
L1 0.50 0.60 0.75
θ10° 8°
CAT93C56, CAT93C57
Doc. No. MD-1088, Rev. R 14 © 2008 SCILLC. All rights reserved
Characteristics subject to change without notice
TDFN 8-Pad 2 x 3mm (VP2) (1)
Notes:
(1) All dimensions are in millimeters.
(2) Complies with JEDEC standard MO-229.
For current Tape and Reel information, download the PDF file from:
http://www.catsemi.com/documents/tapeandreel.pdf.
PIN#1
IDENTIFICATION
E2
E
A3
eb
D
A2
TOP VIEW SIDE VIEW BOTTOM VIEW
PIN#1 INDEX AREA
FRONT VIEW
A1
A
L
D2
SYMBOL MIN NOM MAX
A 0.70 0.75 0.80
A1 0.00 0.02 0.05
A2 0.45 0.55 0.65
A3 0.20 REF
b 0.20 0.25 0.30
D 1.90 2.00 2.10
D2 1.30 1.40 1.50
E 2.90 3.00 3.10
E2 1.20 1.30 1.40
e 050TYP
L 0.20 0.30 0.40
CAT93C56, CAT93C57
© 2008 SCILLC. All rights reserved 15 Doc. No. MD-1088. Rev. R
Characteristics subject to change without notice
TDFN 8-Pad 3 x 3mm (ZD4) (1)
Notes:
(1) All dimensions are in millimeters.
(2) Complies with JEDEC MO-229.
For current Tape and Reel information, download the PDF file from:
http://www.catsemi.com/documents/tapeandreel.pdf.
E2
A3
eb
A
A1
SID E VIEW BOTTOM VI EW
E
D
TOP VIEW
PIN#1 INDEX AREA
PIN#1 ID
FRONT VIEW
A1
A
L
D2
SYMBOL MIN NOM MAX
A 0.70 0.75 0.80
A1 0.00 0.02 0.05
A3 0.20 REF
b 0.23 0.30 0.37
D 2.90 3.00 3.10
D2 2.20 — 2.50
E 2.90 3.00 3.10
E2 1.40 — 1.80
e0.65TYP
L 0.20 0.30 0.40
CAT93C56, CAT93C57
Doc. No. MD-1088, Rev. R 16 © 2008 SCILLC. All rights reserved
Characteristics subject to change without notice
EXAMPLE OF ORDERING INFORMATION
CAT93C56, Die Rev. G, New Product
Notes:
(1) All packages are RoHS-compliant (Lead-free, Halogen-free).
(2) The standard lead finish is NiPdAu.
(3) The device used in the above example is a CAT93C56VI-GT3 (SOIC, Industrial Temperature, NiPdAu, Tape & Reel).
(4) For SOIC, EIAJ (X) package the standard lead finish is Matte-Tin. This package is available in 2,000 pcs/reel, i.e. CAT93C56XI-T2.
(5) For additional package and temperature options, please contact your nearest ON Semiconductor sales office.
CAT93C56/57, Die Rev. E, Mature Product
(CAT93C56, Rev. E – Not Recommended for new Designs)
Notes:
(1) All packages are RoHS-compliant (Lead-free, Halogen-free).
(2) The standard finish is NiPdAu.
(3) The device used in the above example is a CAT93C56VI-1.8-GT3 (SOIC green package, Industrial Temperature, 1.8 Volt to 5.5 Volt
Operating Voltage, NiPdAu finish, Tape & Reel.)
(4) Product die revision letter is marked on top of the package as a suffix to the production date code (e.g., A YWWE). For addi tional infor ma-
tion, please contact your ON Semiconductor sales office.
(5) For SOIC, EIAJ (X) package the standard lead finish is Matte-Tin. This package is available in 2,000 pcs/reel, i.e. CAT93C56XI-T2.
(6) For additional package and temperature options, please contact your nearest ON Semiconductor sales office.
Prefix Device # Suffix
CAT 93C56 V I -1.8 -G T3 Rev E
(
4)
Operating Voltage
Blank: VCC = 2.5V to 5.5V
1.8: VCC = 1.8V to 5.5V
Company ID
Product Numbe
r
93C56
93C57
Temperature Range
I = Industrial (-40ºC to 85ºC)
A = Automotive (-40ºC to 105ºC)
E = Extended
(
-40ºC to 125ºC
)
Lead Finish
Blank: Matte-Tin
G: NiPdAu
Die Revision
93C56: E
93C57: E
Package
L: PDIP
V: SOIC, JEDEC
W: SOIC, JEDEC
X: SOIC, EIAJ(5)
Y: TSSOP
ZD4: TDFN (3x3mm)
Tape & Reel
T: Tape & Reel
2: 2,000 units/Reel(5)
3: 3
,
000 units/Reel
Prefix Device # Suffix
CAT 93C56 V I -G T3
Company ID
Product Numbe
r
93C56
Temperature Range
I = Industrial (-40ºC to +85ºC)
E = Extended (-40ºC to +125ºC)
Lead Finish
Blank: Matte-Tin
G: NiPdAu
Package
L: PDIP
V: SOIC, JEDEC
X: SOIC, EIAJ(4)
Y: TSSOP
VP2: TDFN (2x3mm) Tape & Reel
T: Tape & Reel
2: 2,000 units/Reel(4)
3: 3
,
000 units/Reel
CAT93C56, CAT93C57
© 2008 SCILLC. All rights reserved. 17 Doc. No. MD-1088 Rev. R
Characteristics subject to change without notice
REVISION HISTORY
Date Rev. Comments
14-Apr-04 L New Data Sheet Created From CAT93C46/56/57/66/86. Parts CAT93C56, CAT93C56,
CAT93C57, CAT93C56/57, CAT93C76 and CAT93C86 have be en separated into
single data sheets
12-Oct-06 M
Updated Instruction Set
18-Mar-05 N
Updated Description
13-Oct-06 O Update Features
Update Pin Configuration
Update Functional Symbol
Update Pin Functions
Update D.C. Operating Characteristics (VCC Range)
Update A.C. Characteristics (VCC Range)
Update Ordering Information
21-Aug-07 P
Updated Features/De s cription
Remove "Die Rev E" from the title
Update Pin Configuration / Packages
Update Absolute Maximum Rating
Update Reliability Characteristics
Update D.C. Operating Characteristics
Added D.C. / A.C. Characteristics for CAT93C56 Die Rev G
Rearrange / Format Text and Figures
Update Package Outline Drawings
Added Example of Ordering Information for CAT9 3C56 Die Rev. G
Add MD- to document number
10-Apr-08 Q
Add Extended Temperature Range
Update Package Outline Drawings
27-Oct-08 R Change logo and fine print to ON Semiconductor
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to
any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCIL LC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer
purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and
distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated
with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORM ATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303-675-2175 or 800- 344- 3 86 0 Toll F r ee USA/Ca na da
Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada
Email: orderlit@onse mi.com
N. American Technical Support: 800-282-9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center:
Phone: 81-3-5773-3850
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
