TSOP352.., TSOP354.. Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES * Very low supply current * Photo detector and preamplifier in one package * Internal filter for PCM frequency * Supply voltage range: 2.5 V to 5.5 V 1 2 3 * Improved immunity against modulated light sources 4 * Insensitive to supply voltage ripple and noise 16797 * Taping available for topview and sideview assembly * Compliant to RoHS directive 2002/95/EC accordance to WEEE 2002/96/EC MECHANICAL DATA and in Pinning: DESCRIPTION 1 = GND, 2 = N.C., 3 = VS, 4 = OUT The TSOP352.., TSOP354.. series are miniaturized SMD IR receiver modules for infrared remote control systems. PIN diode and preamplifier are assembled on lead frame, the epoxy package is designed as IR filter. The demodulated output signal can directly be decoded by a microprocessor. The TSOP352.. is compatible with all common IR remote control data formats. The TSOP354.. is optimized to suppress almost all spurious pulses from energy saving lamps but will also suppress some data signals. This component has not been qualified according to automotive specifications. PARTS TABLE CARRIER FREQUENCY STANDARD APPLICATIONS (AGC2/AGC8) VERY NOISY ENVIRONMENTS (AGC4) 30 kHz TSOP35230 TSOP35430 33 kHz TSOP35233 TSOP35433 36 kHz TSOP35236 TSOP35436 38 kHz TSOP35238 TSOP35438 40 kHz TSOP35240 TSOP35440 56 kHz TSOP35256 TSOP35456 APPLICATION CIRCUIT 3 30 k VS 4 Input AGC Band pass Demo dulator OUT 17170_5 Transmitter with TSALxxxx R1 IR receiver VS Circuit BLOCK DIAGRAM + VS C1 C OUT GND VO GND 1; 2 PIN 16839 Document Number: 81781 Rev. 1.4, 13-Aug-09 Control circuit GND R1 and C1 are recommended for protection against EOS. Components should be in the range of 33 < R1 < 1 k, C1 > 0.1 F. www.vishay.com 1 TSOP352.., TSOP354.. IR Receiver Modules for Remote Control Systems Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS (1) PARAMETER SYMBOL VALUE Supply voltage (pin 3) TEST CONDITION VS - 0.3 to + 6.0 UNIT V Supply current (pin 3) IS 3 mA Output voltage (pin 4) VO - 0.3 to (VS + 0.3) V Output current (pin 4) IO 5 mA C Tj 100 Storage temperature range Tstg - 40 to + 100 C Operating temperature range Tamb - 30 to + 85 C Ptot 10 mW Junction temperature Tamb 85 C Power consumption Note (1) Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability. ELECTRICAL AND OPTICAL CHARACTERISTICS (1) PARAMETER Supply current (pin 3) TEST CONDITION SYMBOL MIN. TYP. MAX. Ev = 0, VS = 3.3 V ISD 0.27 0.35 0.45 Ev = 40 klx, sunlight ISH Supply voltage d IOSL = 0.5 mA, Ee = 0.7 mW/m2, test signal see fig. 1 VOSL Minimum irradiance Pulse width tolerance: tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 1 Ee min. Maximum irradiance tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 1 Ee max. Angle of half transmission distance 1/2 Directivity mA 2.5 VS Output voltage low (pin 4) mA 0.45 Ev = 0, test signal see fig. 1, IR diode TSAL6200, IF = 250 mA Transmission distance UNIT 5.5 V 45 m 0.15 100 mV 0.35 mW/m2 W/m2 30 50 deg Note (1) T amb = 25 C, unless otherwise specified TYPICAL CHARACTERISTICS Tamb = 25 C, unless otherwise specified 1 Optical Test Signal (IR diode TSAL6200, IF = 0.4 A, 30 pulses, f = f0, t = 10 ms) t tpi * * tpi VO T 10/f0 is recommended for optimal function Output Signal 1) 2) VOH 16110 7/f0 < td < 15/f0 tpi - 5/f0 < tpo < tpi + 6/f 0 tpo - Output Pulse Width (ms) Ee Output Pulse Width 0.9 0.8 Input Burst Length 0.7 0.6 0.5 0.4 0.3 = 950 nm, Optical Test Signal, Fig.1 0.2 0.1 0 VOL td 1) tpo 2) Fig. 1 - Output Active Low www.vishay.com 2 0.1 t 20752 1 10 102 103 104 105 Ee - Irradiance (mW/m) Fig. 2 - Pulse Length and Sensitivity in Dark Ambient Document Number: 81781 Rev. 1.4, 13-Aug-09 TSOP352.., TSOP354.. Optical Test Signal Ee 600 s t 600 s t = 60 ms 94 8134 Output Signal, (see fig. 4) VO VOH Ee min. - Threshold Irradiance (mW/m) IR Receiver Modules for Remote Control Systems Vishay Semiconductors 4 Correlation with Ambient Light Sources: 3.5 10 W/m = 1.4 kLx (Std. illum. A, T = 2855 K) 10 W/m = 8.2 kLx (Daylight, T = 5900 K) 3 Wavelength of Ambient Illumination: = 950 nm 2.5 2 1.5 1 0.5 0 0.01 VOL t on t t off 20757 Fig. 3 - Output Function Ee min. - Threshold Irradiance (mW/m) Ton, Toff - Output Pulse Width (ms) Ton 0.6 0.5 Toff 0.4 0.3 0.2 0.1 0 0.1 20759 = 950 nm, Optical Test Signal, Fig. 3 1 10 100 1000 100 Ee - Irradiance (mW/m) f = 100 Hz 0.8 f = 10 kHz 0.7 0.6 f = 20 kHz 0.5 0.4 f = 30 kHz 0.3 f = fo 0.2 0.1 0 1 10 100 1000 VsRMS - AC Voltage on DC Supply Voltage (mV) 20753 Fig. 7 - Sensitivity vs. Supply Voltage Disturbances 1.2 E - Max. Field Strength (V/m) 500 1.0 E e min./Ee - Rel. Responsivity 10 1 0.9 10 000 Fig. 4 - Output Pulse Diagram 0.8 0.6 0.4 f = f0 5 % f(3 dB) = f0/10 0.2 450 400 350 300 250 200 150 100 50 0.0 0 0.7 16925 1 Fig. 6 - Sensitivity in Bright Ambient 0.8 0.7 0.1 Ee - Ambient DC Irradiance (W/m) 0.9 1.1 1.3 f/f0 - Relative Frequency Fig. 5 - Frequency Dependence of Responsivity Document Number: 81781 Rev. 1.4, 13-Aug-09 0 20747 500 1000 1500 2000 2500 3000 f - EMI Frequency (MHz) Fig. 8 - Sensitivity vs. Electric Field Disturbances www.vishay.com 3 TSOP352.., TSOP354.. IR Receiver Modules for Remote Control Systems Vishay Semiconductors 0 1 10 20 30 Max. Envelope Duty Cycle 0.9 0.8 0.7 40 0.6 1.0 0.5 0.4 TSOP352.. 0.3 0.9 50 0.8 60 70 TSOP354.. 0.2 0.7 0.1 80 f = 38 kHz, Ee = 2 mW/m 0 0 20868 20 40 60 80 100 120 Burst Length (number of cycles/burst) 0.6 Fig. 9 - Maximum Envelope Duty Cycle vs. Burst Length 0.2 0 0.2 0.6 0.4 Fig. 12 - Horizontal Directivity 0.2 0.3 Ee min. - Sensitivity (mW/m) Ee min. - Threshold Irradiance (mW/m) 0.4 d rel - Relative Transmission Distance 16801 0.25 0.2 0.15 0.1 0.05 0.18 0.16 0.14 0.12 0.1 0.08 0.06 0.04 0.02 0 - 30 - 10 10 30 50 70 Tamb - Ambient Temperature (C) 20755 0 90 2 20756 Fig. 10 - Sensitivity vs. Ambient Temperature 2.5 3 3.5 4 4.5 5 5.5 6 VS - Supply Voltage (V) Fig. 13 - Sensitivity vs. Supply Voltage S ( ) rel - Relative Spectral Sensitivity 1.2 1.0 0.8 0.6 0.4 0.2 0.0 750 16919 850 950 1050 1150 - Wavelength (nm) Fig. 11 - Relative Spectral Sensitivity vs. Wavelength www.vishay.com 4 Document Number: 81781 Rev. 1.4, 13-Aug-09 TSOP352.., TSOP354.. IR Receiver Modules for Remote Control Systems Vishay Semiconductors The TSOP352.., TSOP354.. series is designed to suppress spurious output pulses due to noise or disturbance signals. Data and disturbance signals can be distinguished by the devices according to carrier frequency, burst length and envelope duty cycle. The data signal should be close to the band-pass center frequency (e.g. 38 kHz) and fulfill the conditions in the table below. IR Signal SUITABLE DATA FORMAT When a data signal is applied to the TSOP352.., TSOP354.. in the presence of a disturbance signal, the sensitivity of the receiver is reduced to insure that no spurious pulses are present at the output. Some examples of disturbance signals which are suppressed are IR Signal from Fluorescent Lamp with Low Modulation * Continuous signals at any frequency 5 0 * DC light (e.g. from tungsten bulb or sunlight) 10 15 20 Time (ms) 16920 Fig. 14 - IR Signal from Fluorescent Lamp with Low Modulation * Strongly or weakly modulated noise from fluorescent lamps with electronic ballasts (see figure 14 or figure 15) IR Signal IR Signal from Fluorescent Lamp with High Modulation 0 10 16921 10 15 20 Time (ms) Fig. 15 - IR Signal from Fluorescent Lamp with High Modulation TSOP352.. TSOP354.. Minimum burst length 10 cycles/burst 10 cycles/burst After each burst of length a minimum gap time is required of 10 to 70 cycles 10 cycles 10 to 35 cycles 10 cycles For bursts greater than a minimum gap time in the data stream is needed of 70 cycles > 4 x burst length 35 cycles > 10 x burst length Maximum number of continuous short bursts/second 1800 1500 Recommended for NEC code yes yes Recommended for RC5/RC6 code yes yes Recommended for Sony code yes no Recommended for Thomson 56 kHz code yes yes Recommended for Mitsubishi code (38 kHz, preburst 8 ms, 16 bit) yes no Recommended for Sharp code yes yes Most common disturbance signals are suppressed Even extreme disturbance signals are suppressed Suppression of interference from fluorescent lamps Note For data formats with short bursts please see the datasheet for TSOP351.., TSOP353.. Document Number: 81781 Rev. 1.4, 13-Aug-09 www.vishay.com 5 TSOP352.., TSOP354.. IR Receiver Modules for Remote Control Systems Vishay Semiconductors PACKAGE DIMENSIONS in millimeters 7.5 0.5 Pick and place area. TT taping (1.5) 2.8 5.3 O 2.2 7.2 1 4 (1.4) 0.5 1.27 2.9 0.5 4x 3 x 1.27 = 3.81 4 5.51 Not indicated tolerances 0.3 Pick and place area. TR taping 2.6 technical drawings according to DIN specifications Footprint 2.35 3 x 1.27 = 3.81 0.9 2.2 1.27 Drawing-No.: 6.544-5341.01-4 Issue: 7; 23.03.09 R1.7 16776 ASSEMBLY INSTRUCTIONS Reflow Soldering * Reflow soldering must be done within 72 h while stored under a max. temperature of 30 C, 60 % RH after opening the dry pack envelope * Set the furnace temperatures for pre-heating and heating in accordance with the reflow temperature profile as shown in the diagram. Excercise extreme care to keep the maximum temperature below 260 C. The temperature shown in the profile means the temperature at the device surface. Since there is a temperature difference between the component and the circuit board, it should be verified www.vishay.com 6 that the temperature of the device is accurately being measured * Handling after reflow should be done only after the work surface has been cooled off Manual Soldering * Use a soldering iron of 25 W or less. Adjust the temperature of the soldering iron below 300 C * Finish soldering within 3 s * Handle products only after the temperature has cooled off Document Number: 81781 Rev. 1.4, 13-Aug-09 TSOP352.., TSOP354.. IR Receiver Modules for Remote Control Systems Vishay Semiconductors VISHAY LEAD (Pb)-FREE REFLOW SOLDER PROFILE 300 max. 260 C 245 C 255 C 240 C 217 C 250 T (C) 200 max. 20 s 150 max. 100 s max. 120 s 100 max. Ramp Up 3 C/s max. Ramp Down 6 C/s 50 0 0 19800 50 100 150 t (s) 200 250 300 max. 2 cycles allowed TAPING VERSION TSOP..TT Dimensions in millimeters 16584 Document Number: 81781 Rev. 1.4, 13-Aug-09 www.vishay.com 7 TSOP352.., TSOP354.. Vishay Semiconductors IR Receiver Modules for Remote Control Systems TAPING VERSION TSOP..TR Dimensions in millimeters 16585 www.vishay.com 8 Document Number: 81781 Rev. 1.4, 13-Aug-09 TSOP352.., TSOP354.. IR Receiver Modules for Remote Control Systems Vishay Semiconductors REEL DIMENSIONS in millimeters 16734 LEADER AND TRAILER Dimensions in millimeters Trailer no devices Leader devices no devices End Start min. 200 min. 400 96 11818 COVER TAPE PEEL STRENGTH LABEL According to DIN EN 60286-3 0.1 to 1.3 N 300 10 mm/min. 165 to 180 peel angle Standard bar code labels for finished goods Document Number: 81781 Rev. 1.4, 13-Aug-09 The standard bar code labels are product labels and used for identification of goods. The finished goods are packed in final packing area. The standard packing units are labeled with standard bar code labels before transported as finished goods to warehouses. The labels are on each packing unit and contain Vishay Semiconductor GmbH specific data. www.vishay.com 9 TSOP352.., TSOP354.. Vishay Semiconductors IR Receiver Modules for Remote Control Systems VISHAY SEMICONDUCTOR GMBH STANDARD BAR CODE PRODUCT LABEL (Finished Goods) PLAIN WRITTING ABBREVIATION LENGTH - 18 Item-number INO 8 Selection-code SEL 3 BATCH 10 Data-code COD 3 (YWW) Plant-code PTC 2 Quantity QTY 8 Accepted by ACC - Packed by PCK - Item-description LOT-/serial-number Mixed code indicator MIXED CODE - xxxxxxx+ Company logo Origin TYPE LENGTH Item-number LONG BAR CODE TOP N 8 Plant-code N 2 Sequence-number X 3 Quantity N 8 Total length - 21 TYPE LENGTH SHORT BAR CODE BOTTOM Selection-code X 3 Data-code N 3 Batch-number X 10 Filter - 1 Total length - 17 DRY PACKING The reel is packed in an anti-humidity bag to protect the devices from absorbing moisture during transportation and storage. Aluminum bag Label After more than 72 h under these conditions moisture content will be too high for reflow soldering. In case of moisture absorption, the devices will recover to the former condition by drying under the following condition: 192 h at 40 C + 5 C/ - 0 C and < 5 % RH (dry air/nitrogen) or 96 h at 60 C + 5 C and < 5 % RH for all device containers or 24 h at 125 C + 5 C not suitable for reel or tubes. An EIA JEDEC standard JESD22-A112 level 4 label is included on all dry bags. Reel 15973 FINAL PACKING The sealed reel is packed into a cardboard box. A secondary cardboard box is used for shipping purposes. RECOMMENDED METHOD OF STORAGE Dry box storage is recommended as soon as the aluminum bag has been opened to prevent moisture absorption. The following conditions should be observed, if dry boxes are not available: * Storage temperature 10 C to 30 C * Storage humidity 60 % RH max. www.vishay.com 10 16943 Example of JESD22-A112 level 4 label Document Number: 81781 Rev. 1.4, 13-Aug-09 TSOP352.., TSOP354.. IR Receiver Modules for Remote Control Systems ESD PRECAUTION Proper storage and handling procedures should be followed to prevent ESD damage to the devices especially when they are removed from the antistatic shielding bag. Electro-static sensitive devices warning labels are on the packaging. Vishay Semiconductors VISHAY SEMICONDUCTORS STANDARD BAR CODE LABELS The Vishay Semiconductors standard bar code labels are printed at final packing areas. The labels are on each packing unit and contain Vishay Semiconductors specific data. 16962 Document Number: 81781 Rev. 1.4, 13-Aug-09 www.vishay.com 11 Legal Disclaimer Notice Vishay Disclaimer All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 18-Jul-08 www.vishay.com 1