TSOP35230TR - Vishay Presicion Group

Document Number: 81781 www.vishay.com

Rev. 1.4, 13-Aug-09 1

IR Receiver Modules for Remote Control Systems

TSOP352.., TSOP354..

Vishay Semiconductors

MECHANICAL DATA

Pinning:

1 = GND, 2 = N.C., 3 = VS, 4 = OUT

FEATURES

• Very low supply current

• Photo detector and preamplifier in one package

• Internal filter for PCM frequency

• Supply voltage range: 2.5 V to 5.5 V

• Improved immunity against modulated light

sources

• Insensitive to supply voltage ripple and noise

• Taping available for topview and sideview assembly

• Compliant to RoHS directive 2002/95/EC and in

accordance to WEEE 2002/96/EC

DESCRIPTION

The TSOP352.., TSOP354.. series are miniaturized SMD IR

receiver modules for infrared remote control systems. PIN

diode and preamplifier are assembled on lead frame, the

epoxy package is designed as IR filter.

The demodulated output signal can directly be decoded by a

microprocessor. The TSOP352.. is compatible with all

common IR remote control data formats. The TSOP354.. is

optimized to suppress almost all spurious pulses from

energy saving lamps but will also suppress some data

signals.

This component has not been qualified according to

automotive specifications.

BLOCK DIAGRAM APPLICATION CIRCUIT

16797

1234

PARTS TABLE

CARRIER FREQUENCY STANDARD APPLICATIONS (AGC2/AGC8) VERY NOISY ENVIRONMENTS (AGC4)

30 kHz TSOP35230 TSOP35430

33 kHz TSOP35233 TSOP35433

36 kHz TSOP35236 TSOP35436

38 kHz TSOP35238 TSOP35438

40 kHz TSOP35240 TSOP35440

56 kHz TSOP35256 TSOP35456

30 kΩ

OUT

Demo -

GND

pass

AGCInput

Band

dulator

Control circuit

1; 2

16839

IR receiver

GND

Circuit

µC

+ VS

GND

Transmitter

with

TSALxxxx VS

17170_5

OUT

R1 and C1 are recommended for protection against EOS.

Components should be in the range of 33 Ω < R1 < 1 kΩ,

C1 > 0.1 µF.

www.vishay.com Document Number: 81781

2Rev. 1.4, 13-Aug-09

TSOP352.., TSOP354..

Vishay Semiconductors IR Receiver Modules for Remote

Control Systems

Note

(1) Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only

and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification

is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability.

Note

(1) Tamb = 25 °C, unless otherwise specified

TYPICAL CHARACTERISTICS

Tamb = 25 °C, unless otherwise specified

Fig. 1 - Output Active Low Fig. 2 - Pulse Length and Sensitivity in Dark Ambient

ABSOLUTE MAXIMUM RATINGS (1)

PARAMETER TEST CONDITION SYMBOL VALUE UNIT

Supply voltage (pin 3) VS- 0.3 to + 6.0 V

Supply current (pin 3) IS3mA

Output voltage (pin 4) VO- 0.3 to (VS + 0.3) V

Output current (pin 4) IO5mA

Junction temperature Tj100 °C

Storage temperature range Tstg - 40 to + 100 °C

Operating temperature range Tamb - 30 to + 85 °C

Power consumption Tamb ≤ 85 °C Ptot 10 mW

ELECTRICAL AND OPTICAL CHARACTERISTICS (1)

PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT

Supply current (pin 3) Ev = 0, VS = 3.3 V ISD 0.27 0.35 0.45 mA

Ev = 40 klx, sunlight ISH 0.45 mA

Supply voltage VS2.5 5.5 V

Transmission distance

Ev = 0, test signal see fig. 1,

IR diode TSAL6200,

IF = 250 mA

d45m

Output voltage low (pin 4) IOSL = 0.5 mA, Ee = 0.7 mW/m2,

test signal see fig. 1 VOSL 100 mV

Minimum irradiance

Pulse width tolerance:

tpi - 5/fo < tpo < tpi + 6/fo,

test signal see fig. 1

Ee min. 0.15 0.35 mW/m2

Maximum irradiance tpi - 5/fo < tpo < tpi + 6/fo,

test signal see fig. 1 Ee max. 30 W/m2

Directivity Angle of half transmission distance ϕ1/2 ± 50 deg

* t

10/f

is recommended for optimal function

16110

Optical Test Signal

(IR diode TSAL6200, I

= 0.4 A, 30 pulses, f = f

, t = 10 ms)

Output Signal

1) tpo 2)

1) 7/f

<15/f

2) t

- 5/f

< t

+ 6/f

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

0.1 1 10 102103104105

Ee - Irradiance (mW/m²)

tpo - Output Pulse Width (ms)

20752

Input Burst Length

λ = 950 nm,

Optical Test Signal, Fig.1

Output Pulse Width

Document Number: 81781 www.vishay.com

Rev. 1.4, 13-Aug-09 3

TSOP352.., TSOP354..

IR Receiver Modules for Remote

Control Systems Vishay Semiconductors

Fig. 3 - Output Function

Fig. 4 - Output Pulse Diagram

Fig. 5 - Frequency Dependence of Responsivity

Fig. 6 - Sensitivity in Bright Ambient

Fig. 7 - Sensitivity vs. Supply Voltage Disturbances

Fig. 8 - Sensitivity vs. Electric Field Disturbances

600 µs 600 µs

t = 60 ms

off

94 8134

Optical Test Signal

Output Signal, (see fig. 4)

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.1 1 10 100 1000 10 000

Ee - Irradiance (mW/m²)

Ton, Toff - Output Pulse Width (ms)

20759

λ = 950 nm,

Optical Test Signal, Fig. 3

Ton

Toff

0.0

0.2

0.4

0.6

0.8

1.0

1.2

0.7 0.9 1.1 1.3

f/f0 - Relative Frequency

16925

f = f0 ± 5 %

Δ f(3 dB) = f0/10

E /E - Rel. Responsivity

e min. e

0.5

1.5

2.5

3.5

0.01 0.1 1 10 100

Ee - Ambient DC Irradiance (W/m²)

Ee min. - Threshold Irradiance (mW/m²)

Correlation with Ambient Light Sources:

10 W/m² = 1.4 kLx (Std. illum. A, T = 2855 K)

10 W/m² = 8.2 kLx (Daylight, T = 5900 K)

Wavelength of Ambient

Illumination:

= 950 nm

20757

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

1 10 100 1000

VsRMS - AC Voltage on DC Supply Voltage (mV)

20753

Ee min. - Threshold Irradiance (mW/m²)

f = f

f = 20 kHz

f = 30 kHz

f = 100 Hz

f = 10 kHz

100

150

200

250

300

350

400

450

500

0 500 1000 1500 2000 2500 3000

f - EMI Frequency (MHz)

E - Max. Field Strength (V/m)

20747

www.vishay.com Document Number: 81781

4Rev. 1.4, 13-Aug-09

TSOP352.., TSOP354..

Vishay Semiconductors IR Receiver Modules for Remote

Control Systems

Fig. 9 - Maximum Envelope Duty Cycle vs. Burst Length

Fig. 10 - Sensitivity vs. Ambient Temperature

Fig. 11 - Relative Spectral Sensitivity vs. Wavelength

Fig. 12 - Horizontal Directivity

Fig. 13 - Sensitivity vs. Supply Voltage

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

020406080 100 120

Burst Length (number of cycles/burst)

Max. Envelope Duty Cycle

f = 38 kHz, Ee = 2 mW/m²

TSOP352..

TSOP354..

20868

0.05

0.1

0.15

0.2

0.25

0.3

- 30 - 10 10 30 50 70 90

Tamb - Ambient Temperature (°C)

Ee min. - Threshold Irradiance (mW/m²)

20755

0.0

0.2

0.4

0.6

0.8

1.0

1.2

750 850 950 1050 1150

λ-Wavelength (nm)

16919

S ( ) - Relative Spectral Sensitivityλrel

16801

0.4 0.2 0 0.2 0.4 0.6

0.6

0.9

0°

30°

10° 20°

40°

50°

60°

70°

80°

1.0

0.8

0.7

drel - Relative Transmission Distance

0.02

0.04

0.06

0.08

0.1

0.12

0.14

0.16

0.18

0.2

23456

VS - Supply Voltage (V)

Ee min. - Sensitivity (mW/m²)

20756

3.5 4.5 5.5

2.5

Document Number: 81781 www.vishay.com

Rev. 1.4, 13-Aug-09 5

TSOP352.., TSOP354..

IR Receiver Modules for Remote

Control Systems Vishay Semiconductors

SUITABLE DATA FORMAT

The TSOP352.., TSOP354.. series is designed to suppress

spurious output pulses due to noise or disturbance signals.

Data and disturbance signals can be distinguished by the

devices according to carrier frequency, burst length and

envelope duty cycle. The data signal should be close to the

band-pass center frequency (e.g. 38 kHz) and fulfill the

conditions in the table below.

When a data signal is applied to the TSOP352.., TSOP354..

in the presence of a disturbance signal, the sensitivity of the

receiver is reduced to insure that no spurious pulses are

present at the output. Some examples of disturbance signals

which are suppressed are

• DC light (e.g. from tungsten bulb or sunlight)

• Continuous signals at any frequency

• Strongly or weakly modulated noise from fluorescent

lamps with electronic ballasts (see figure 14 or figure 15)

Fig. 14 - IR Signal from Fluorescent Lamp

with Low Modulation

Fig. 15 - IR Signal from Fluorescent Lamp

with High Modulation

Note

For data formats with short bursts please see the datasheet for TSOP351.., TSOP353..

0101520

Time (ms)

16920

IR Signal

IR Signal from Fluorescent

Lamp with Low Modulation

0101520

Time (ms)

16921

IR Signal

IR Signal from Fluorescent

Lamp with High Modulation

TSOP352.. TSOP354..

Minimum burst length 10 cycles/burst 10 cycles/burst

After each burst of length

a minimum gap time is required of

10 to 70 cycles

≥ 10 cycles

10 to 35 cycles

≥ 10 cycles

For bursts greater than

a minimum gap time in the data stream is needed of

70 cycles

> 4 x burst length

35 cycles

> 10 x burst length

Maximum number of continuous short bursts/second 1800 1500

Recommended for NEC code yes yes

Recommended for RC5/RC6 code yes yes

Recommended for Sony code yes no

Recommended for Thomson 56 kHz code yes yes

Recommended for Mitsubishi code (38 kHz, preburst 8 ms, 16 bit) yes no

Recommended for Sharp code yes yes

Suppression of interference from fluorescent lamps Most common disturbance

signals are suppressed

Even extreme disturbance

signals are suppressed

www.vishay.com Document Number: 81781

6Rev. 1.4, 13-Aug-09

TSOP352.., TSOP354..

Vishay Semiconductors IR Receiver Modules for Remote

Control Systems

PACKAGE DIMENSIONS in millimeters

ASSEMBLY INSTRUCTIONS

Reflow Soldering

• Reflow soldering must be done within 72 h while stored

under a max. temperature of 30 °C, 60 % RH after opening

the dry pack envelope

• Set the furnace temperatures for pre-heating and heating

in accordance with the reflow temperature profile as shown

in the diagram. Excercise extreme care to keep the

maximum temperature below 260 °C. The temperature

shown in the profile means the temperature at the device

surface. Since there is a temperature difference between

the component and the circuit board, it should be verified

that the temperature of the device is accurately being

measured

• Handling after reflow should be done only after the work

surface has been cooled off

Manual Soldering

• Use a soldering iron of 25 W or less. Adjust the

temperature of the soldering iron below 300 °C

• Finish soldering within 3 s

• Handle products only after the temperature has cooled off

2.35

R1.7

5.51

0.5

3 x 1.27 = 3.81

2.6

7.5 ± 0.5

7.2

1.27

5.3

2.9 ± 0.5

Ø 2.2

Pick and place area. TR taping

2.2

3 x 1.27 = 3.81

1.27 0.9

2.8

specifications

according to DIN

technical drawings

Drawing-No.: 6.544-5341.01-4

Issue: 7; 23.03.09

16776

Not indicated tolerances ± 0.3

Pick and place area. TT taping

Footprint

(1.5)

(1.4)

Document Number: 81781 www.vishay.com

Rev. 1.4, 13-Aug-09 7

TSOP352.., TSOP354..

IR Receiver Modules for Remote

Control Systems Vishay Semiconductors

VISHAY LEAD (Pb)-FREE REFLOW SOLDER PROFILE

TAPING VERSION TSOP..TT Dimensions in millimeters

100

150

200

250

300

0 50 100 150 200 250 300

t (s)

T (°C)

255 °C

240 °C 245 °

max. 260 °C

max. 120 s max. 100 s

217 °C

max. 20 s

max. Ramp Up 3 °C/s max. Ramp Down 6 °C/s

max. 2 cycles allowed

19800

16584

www.vishay.com Document Number: 81781

8Rev. 1.4, 13-Aug-09

TSOP352.., TSOP354..

Vishay Semiconductors IR Receiver Modules for Remote

Control Systems

TAPING VERSION TSOP..TR Dimensions in millimeters

16585

Document Number: 81781 www.vishay.com

Rev. 1.4, 13-Aug-09 9

TSOP352.., TSOP354..

IR Receiver Modules for Remote

Control Systems Vishay Semiconductors

REEL DIMENSIONS in millimeters

LEADER AND TRAILER Dimensions in millimeters

COVER TAPE PEEL STRENGTH

According to DIN EN 60286-3

0.1 to 1.3 N

300 ± 10 mm/min.

165° to 180° peel angle

LABEL

Standard bar code labels for finished goods

The standard bar code labels are product labels and used for

identification of goods. The finished goods are packed in final

packing area. The standard packing units are labeled with

standard bar code labels before transported as finished

goods to warehouses. The labels are on each packing unit

and contain Vishay Semiconductor GmbH specific data.

16734

Trailer Leader

no devices

min.

200

min. 400

StartEnd

devices

96 11818

no devices

www.vishay.com Document Number: 81781

10 Rev. 1.4, 13-Aug-09

TSOP352.., TSOP354..

Vishay Semiconductors IR Receiver Modules for Remote

Control Systems

DRY PACKING

The reel is packed in an anti-humidity bag to protect the

devices from absorbing moisture during transportation and

storage.

FINAL PACKING

The sealed reel is packed into a cardboard box. A secondary

cardboard box is used for shipping purposes.

RECOMMENDED METHOD OF STORAGE

Dry box storage is recommended as soon as the aluminum

bag has been opened to prevent moisture absorption. The

following conditions should be observed, if dry boxes are not

available:

• Storage temperature 10 °C to 30 °C

• Storage humidity ≤ 60 % RH max.

After more than 72 h under these conditions moisture

content will be too high for reflow soldering.

In case of moisture absorption, the devices will recover to the

former condition by drying under the following condition:

192 h at 40 °C + 5 °C/ - 0 °C and < 5 % RH (dry air/nitrogen)

96 h at 60 °C + 5 °C and < 5 % RH for all device containers or

24 h at 125 °C + 5 °C not suitable for reel or tubes.

An EIA JEDEC standard JESD22-A112 level 4 label is

included on all dry bags.

Example of JESD22-A112 level 4 label

VISHAY SEMICONDUCTOR GMBH STANDARD BAR CODE PRODUCT LABEL (Finished Goods)

PLAIN WRITTING ABBREVIATION LENGTH

Item-description - 18

Item-number INO 8

Selection-code SEL 3

LOT-/serial-number BATCH 10

Data-code COD 3 (YWW)

Plant-code PTC 2

Quantity QTY 8

Accepted by ACC -

Packed by PCK -

Mixed code indicator MIXED CODE -

Origin xxxxxxx+ Company logo

LONG BAR CODE TOP TYPE LENGTH

Item-number N 8

Plant-code N 2

Sequence-number X 3

Quantity N 8

Total length - 21

SHORT BAR CODE BOTTOM TYPE LENGTH

Selection-code X 3

Data-code N 3

Batch-number X 10

Filter - 1

Total length - 17

Aluminum bag

Label

Reel

15973

16943

Document Number: 81781 www.vishay.com

Rev. 1.4, 13-Aug-09 11

TSOP352.., TSOP354..

IR Receiver Modules for Remote

Control Systems Vishay Semiconductors

ESD PRECAUTION

Proper storage and handling procedures should be followed

to prevent ESD damage to the devices especially when they

are removed from the antistatic shielding bag. Electro-static

sensitive devices warning labels are on the packaging.

VISHAY SEMICONDUCTORS STANDARD

BAR CODE LABELS

The Vishay Semiconductors standard bar code labels are

printed at final packing areas. The labels are on each

packing unit and contain Vishay Semiconductors specific

data.

16962

Document Number: 91000 www.vishay.com

Revision: 18-Jul-08 1

Disclaimer

Legal Disclaimer Notice

Vishay

All product specifications and data are subject to change without notice.

Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf

(collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein

or in any other disclosure relating to any product.

Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any

information provided herein to the maximum extent permitted by law. The product specifications do not expand or

otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed

therein, which apply to these products.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this

document or by any conduct of Vishay.

The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless

otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such

applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting

from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding

products designed for such applications.

Product names and markings noted herein may be trademarks of their respective owners.