CY8C23433, CY8C23533 PSoC(R) Programmable System-on-ChipTM Features Powerful Harvard Architecture Processor M8C Processor Speeds to 24 MHz 8x8 Multiply, 32-Bit Accumulate Low Power at High Speed 3.0 to 5.25V Operating Voltage Industrial Temperature Range: -40C to +85C Advanced Peripherals (PSoC Blocks) 4 Rail-to-Rail analog PSoC Blocks Provide: * Up to 14-Bit ADCs * Up to 8-Bit DACs * Programmable Gain Amplifiers * Programmable Filters and Comparators 4 Digital PSoC Blocks Provide: * 8 to 32-Bit Timers, Counters, and PWMs * CRC and PRS Modules * Full-Duplex UART * Multiple SPITM Masters or Slaves * Connectable to All GPIO Pins Complex Peripherals by Combining Blocks High-Speed 8-Bit SAR ADC Optimized for Motor Control Complete Development Tools Free Development Software (PSoC DesignerTM) Full-Featured In-Circuit Emulator and Programmer Full Speed Emulation Complex Breakpoint Structure 128K Bytes Trace Memory Logic Block Diagram Port 3 Port 2 Port 1 Port 0 Analog Drivers PSoC CORE System Bus Global Digital Interconnect SRAM 256 Bytes SROM Flash 8K CPUCore (M8C) Interrupt Controller Precision, Programmable Clocking Internal 2.5% 24/48 MHz Oscillator High Accuracy 24 MHz with Optional 32 kHz Crystal and PLL Optional External Oscillator, up to 24 MHz Internal Oscillator for Watchdog and Sleep Global Analog Interconnect Sleep and Watchdog Multiple Clock Sources (Includes IMO, ILO, PLL, and ECO) DIGITAL SYSTEM Digital Block Array Flexible On-Chip Memory 8K Bytes Flash Program Storage 50,000 Erase/Write Cycles 256 Bytes SRAM Data Storage In-System Serial Programming (ISSP) Partial Flash Updates Flexible Protection Modes EEPROM Emulation in Flash Analog Block Array 2 Columns 4 Blocks 1 Row 4 Blocks Programmable Pin Configurations 25 mA Sink on all GPIO Pull up, Pull Down, High Z, Strong, or Open Drain Drive Modes on All GPIO Up to Ten Analog Inputs on GPIO Two 30 mA Analog Outputs on GPIO Configurable Interrupt on All GPIO Digital Clocks Multiply Accum. ANALOG SYSTEM SAR8 ADC Decimator I2C Analog Ref Analog Input Muxing POR and LVD System Resets Internal Voltage Ref. SYSTEM RESOURCES Additional System Resources 2 I CTM Slave, Master, and Multi-Master to 400 kHz Watchdog and Sleep Timers User-Configurable Low Voltage Detection Integrated Supervisory Circuit On-chip Precision Voltage Reference Cypress Semiconductor Corporation Document Number: 001-44369 Rev. *B * 198 Champion Court * San Jose, CA 95134-1709 * 408-943-2600 Revised December 05, 2008 [+] Feedback CY8C23433, CY8C23533 PSoC Functional Overview Digital System The PSoC family consists of many mixed-signal array with On-Chip Controller devices. These devices are designed to replace multiple traditional MCU-based system components with a low cost single-chip programmable device. PSoC devices include configurable blocks of analog and digital logic, and programmable interconnects. This architecture allows the user to create customized peripheral configurations that match the requirements of each individual application. Additionally, a fast CPU, Flash program memory, SRAM data memory, and configurable IO are included in a range of convenient pinouts and packages. The Digital System consists of 4 digital PSoC blocks. Each block is an 8-bit resource that is used alone or combined with other blocks to form 8, 16, 24, and 32-bit peripherals, which are called user module references. Figure 1. Digital System Block Diagram Port 3 Port 2 To System Bus Digital Clocks FromCore The PSoC architecture, as shown in the Logic Block Diagram on page 1, consists of four main areas: PSoC Core, Digital System, Analog System, and System Resources. Configurable global busing allows combining all the device resources into a complete custom system. The PSoC CY8C23x33 family can have up to three IO ports that connect to the global digital and analog interconnects, providing access to four digital blocks and four analog blocks. Port 1 Port 0 ToAnalog System DIGITAL SYSTEM Digital PSoC Block Array Row 0 Row Input Configuration 8 DBB00 DBB01 DCB02 4 DCB03 4 8 Row Output Configuration 8 8 PSoC Core The PSoC Core is a powerful engine that supports a rich feature set. The core includes a CPU, memory, clocks, and configurable GPIO (General Purpose IO). The M8C CPU core is a powerful processor with speeds up to 24 MHz, providing a four MIPS 8-bit Harvard architecture microprocessor. The CPU uses an interrupt controller with 11 vectors, to simplify programming of real time embedded events. Program execution is timed and protected using the included Sleep and Watch Dog Timers (WDT). Memory encompasses 8 KB of Flash for program storage, 256 bytes of SRAM for data storage, and up to 2 KB of EEPROM emulated using the Flash. Program Flash uses four protection levels on blocks of 64 bytes, allowing customized software IP protection. The PSoC device incorporates flexible internal clock generators, including a 24 MHz IMO (internal main oscillator) accurate to 2.5% over temperature and voltage. The 24 MHz IMO can also be doubled to 48 MHz for use by the digital system. A low power 32 kHz ILO (internal low speed oscillator) is provided for the Sleep timer and WDT. If crystal accuracy is desired, the ECO (32.768 kHz external crystal oscillator) is available for use as a Real Time Clock (RTC) and can optionally generate a crystal-accurate 24 MHz system clock using a PLL. The clocks, together with programmable clock dividers (as a System Resource), provide the flexibility to integrate almost any timing requirement into the PSoC device. PSoC GPIOs provide connection to the CPU, digital and analog resources of the device. Each pin's drive mode may be selected from eight options, allowing great flexibility in external interfacing. Every pin also has the capability to generate a system interrupt on high level, low level, and change from last read. Document Number: 001-44369 Rev. *B GIE[7:0] GIO[7:0] Global Digital Interconnect GOE[7:0] GOO[7:0] Digital peripheral configurations are: PWMs (8 to 32 bit) PWMs with Dead band (8 to 32 bit) Counters (8 to 32 bit) Timers (8 to 32 bit) UART 8 bit with selectable parity (up to 1) SPI master and slave (up to 1) I2C slave and master (1 available as a System Resource) Cyclical Redundancy Checker/Generator (8 to 32 bit) IrDA (up to 1) Pseudo Random Sequence Generators (8 to 32 bit) The digital blocks can be connected to any GPIO through a series of global buses that can route any signal to any pin. The buses also allow for signal multiplexing and for performing logic operations. This configurability frees your designs from the constraints of a fixed peripheral controller. Digital blocks are provided in rows of four, where the number of blocks varies by PSoC device family. This allows the optimum choice of system resources for your application. Family resources are shown in the table titled PSoC Device Characteristics on page 4. Page 2 of 37 [+] Feedback CY8C23433, CY8C23533 The Analog system consists of an 8-bit SAR ADC and four configurable blocks. The programmable 8-bit SAR ADC is an optimized ADC that runs up to 300 Ksps, with monotonic guarantee. It also has the features to support a motor control application. Each analog block consists of an opamp circuit allowing the creation of complex analog signal flows. Analog peripherals are very flexible and can be customized to support specific application requirements. Some of the more common PSoC analog functions (most available as user modules) are: Filters (2 band pass, low-pass) Amplifiers (up to 2, with selectable gain to 48x) Instrumentation amplifiers (1 with selectable gain to 93x) Comparators (1, with 16 selectable thresholds) DAC (6 or 9 -bit DAC) Multiplying DAC (6 or 9 -bit DAC) High current output drivers (two with 30 mA drive) 1.3V reference (as a System Resource) DTMF dialer Figure 2. Analog System Block Diagram P0[7] P0[6] P0[5] P0[4] P0[3] P0[2] P0[1] P0[0] AGNDIn RefIn Analog System P2[3] P2[6] P2[4] P2[1] P2[2] P2[0] Array Input Configuration ACI0[1:0] ACI1[1:0] Block Array ACB00 Modulators Correlators Peak detectors Many other topologies possible ACB01 ASD11 ASC21 P0[7:0] Analog blocks are arranged in a column of three, which includes one CT (Continuous Time) and two SC (Switched Capacitor) blocks. The Analog Column 0 contains the SAR8 ADC block rather than the standard SC blocks. ACI2[3:0] 8-Bit SAR ADC Analog Reference Interface to Digital System RefHi RefLo AGND Reference Generators AGNDIn RefIn Bandgap M8C Interface (Address Bus, Data Bus, Etc.) Document Number: 001-44369 Rev. *B Page 3 of 37 [+] Feedback CY8C23433, CY8C23533 Getting Started Additional System Resources System Resources, some of which are listed in the previous sections, provide additional capability useful to complete systems. Additional resources include a multiplier, decimator, low voltage detection, and power on reset. Brief statements describing the merits of each system resource follow: Digital clock dividers provide three customizable clock frequencies for use in applications. The clocks can be routed to both the digital and analog systems. Additional clocks can be generated using digital PSoC blocks as clock dividers. A multiply accumulate (MAC) provides a fast 8-bit multiplier with 32-bit accumulate, to assist in both general math and digital filters. The decimator provides a custom hardware filter for digital signal processing applications including the creation of Delta Sigma ADCs. The I2C module provides 100 and 400 kHz communication over two wires. Slave, master, and multi-master modes are all supported. Low Voltage Detection (LVD) interrupts can signal the application of falling voltage levels, while the advanced POR (Power On Reset) circuit eliminates the need for a system supervisor. An internal 1.3V reference provides an absolute reference for the analog system, including ADCs and DACs. PSoC Device Characteristics Depending on the PSoC device characteristics, the digital and analog systems can have 16, 8, or 4 digital blocks and 12, 6, or 3 analog blocks. The following table lists the resources available for specific PSoC device groups. Analog Inputs Analog Outputs Analog Columns Analog Blocks SAR8 ADC up to 4 64 16 12 4 4 12 No CY8C27x43 up to 2 44 8 12 4 4 12 No CY8C24x94 56 1 4 48 2 2 6 No CY8C23X33 up to 1 26 4 12 2 2[1] 4 Yes CY8C24x23A up to 1 24 4 12 2 2 6 No CY8C21x34 up to 1 28 4 28 0 2 4[2] No CY8C21x23 16 4 8 0 2 4[2] No 0 3[3] No CY8C20x34 Digital Rows CY8C29x66 PSoC Part Number Digital IO Digital Blocks Table 1. PSoC Device Characteristics 1 up to 0 28 The quickest path to understanding the PSoC silicon is by reading this data sheet and using the PSoC Designer Integrated Development Environment (IDE). This data sheet is an overview of the PSoC integrated circuit and presents specific pin, register, and electrical specifications. For in-depth information, along with detailed programming information, refer the PSoC Mixed-Signal Array Technical Reference Manual. For latest Ordering, Packaging, and Electrical Specification information, refer the latest PSoC device data sheets on the web at http://www.cypress.com/psoc. To determine which PSoC device meets your requirements, navigate through the PSoC Decision Tree in the Application Note AN2209 at http://www.cypress.com and select Application Notes under the Design Resources. Development Kits Development Kits are available from the following distributors: Digi-Key, Avnet, Arrow, and Future. The Cypress Online Store contains development kits, C compilers, and all accessories for PSoC development. Go to the Cypress Online Store web site at http://www.cypress.com/onlinestore. Technical Training Modules Free PSoC technical training modules are available for users new to PSoC. Training modules cover designing, debugging, advanced analog and CapSense. Go to http://www.cypress.com. Consultants Certified PSoC Consultants offer everything from technical assistance to completed PSoC designs. To contact or become a PSoC Consultant go to http://www.cypress.com, click on Design Support located at the top of the web page, and select CYPros Consultants. Technical Support PSoC application engineers take pride in fast and accurate response. They can be reached with a 4-hour guaranteed response at http://www.cypress.com/support. Application Notes 0 28 0 A long list of application notes can assist you in every aspect of your design effort. To view the PSoC application notes, go to http://www.cypress.com/psocapnotes. Notes 1. One complete column, plus one Continuous Time Block. 2. Limited analog functionality. 3. Two analog blocks and one CapSense. Document Number: 001-44369 Rev. *B Page 4 of 37 [+] Feedback CY8C23433, CY8C23533 Development Tools PSoC Designer Software Subsystems PSoC Designer is a Microsoft(R) Windows-based, integrated development environment for the Programmable System-on-Chip (PSoC) devices. The PSoC Designer IDE and application runs on Windows NT 4.0, Windows 2000, Windows Millennium (Me), or Windows XP (refer section PSoC Designer Subsystems on page 5). Device Editor PSoC Designer helps the customer to select an operating configuration for the PSoC, write application code that uses the PSoC, and debug the application. This system provides design database management by project, an integrated debugger with In-Circuit Emulator, in-system programming support, and the CYASM macro assembler for the CPUs. PSoC Designer also supports a high-level C language compiler developed specifically for the devices in the family. Figure 3. PSoC Designer Subsystems Graphical Designer Interface Context Sensitive Help The device editor also supports easy development of multiple configurations and dynamic reconfiguration. Dynamic configuration allows for changing configurations at run time. PSoC Designer sets up power on initialization tables for selected PSoC block configurations and creates source code for an application framework. The framework contains software to operate the selected components and, if the project uses more than one operating configuration, contains routines to switch between different sets of PSoC block configurations at run time. PSoC Designer can print out a configuration sheet for a given project configuration for use during application programming in conjunction with the Device Data Sheet. Once the framework is generated, the user can add application-specific code to flesh out the framework. It is also possible to change the selected components and regenerate the framework. Design Browser Results Commands PSoC Designer The Device Editor subsystem allows the user to select different onboard analog and digital components called user modules using the PSoC blocks. Examples of user modules are ADCs, DACs, Amplifiers, and Filters. The Design Browser allows users to select and import preconfigured designs into the user's project. Users can easily browse a catalog of preconfigured designs to facilitate time-to-design. Examples provided in the tools include a 300-baud modem, LIN Bus master and slave, fan controller, and magnetic card reader. Importable Design Database Application Editor Device Database Application Database PSoC Designer Core Engine Project Database PSoC Configuration Sheet Manufacturing Information File User Modules Library Emulation Pod In the Application Editor you can edit your C language and Assembly language source code. You can also assemble, compile, link, and build. Assembler. The macro assembler allows the assembly code to be merged seamlessly with C code. The link libraries automatically use absolute addressing or can be compiled in relative mode, and linked with other software modules to get absolute addressing. C Language Compiler. A C language compiler is available that supports the PSoC family of devices. Even if you have never worked in the C language before, the product quickly allows you to create complete C programs for the PSoC family devices. In-Circuit Emulator Document Number: 001-44369 Rev. *B Device Programmer The embedded, optimizing C compiler provides all the features of C tailored to the PSoC architecture. It comes complete with embedded libraries providing port and bus operations, standard keypad and display support, and extended math functionality. Page 5 of 37 [+] Feedback CY8C23433, CY8C23533 Debugger The PSoC Designer Debugger subsystem provides hardware in-circuit emulation, allowing the designer to test the program in a physical system while providing an internal view of the PSoC device. Debugger commands allow the designer to read and program and read and write data memory, read and write IO registers, read and write CPU registers, set and clear breakpoints, and provide program run, halt, and step control. The debugger also allows the designer to create a trace buffer of registers and memory locations of interest. Online Help System The online help system displays online, context-sensitive help for the user. Designed for procedural and quick reference, each functional subsystem has its own context-sensitive help. This system also provides tutorials and links to FAQs and an Online Support Forum to aid the designer in getting started. Hardware Tools In-Circuit Emulator A low cost, high functionality ICE (In-Circuit Emulator) is available for development support. This hardware has the capability to program single devices. The emulator consists of a base unit that connects to the PC by way of a USB port. The base unit is universal and can operate with all PSoC devices. Emulation pods for each device family are available separately. The emulation pod takes the place of the PSoC device in the target board and performs full speed (24 MHz) operation. of resolution. The user module parameters permit you to establish the pulse width and duty cycle. User modules also provide tested software to cut your development time. The user module application programming interface (API) provides high level functions to control and respond to hardware events at run-time. The API also provides optional interrupt service routines that you can adapt as needed. The API functions are documented in user module data sheets that are viewed directly in the PSoC Designer IDE. These data sheets explain the internal operation of the user module and provide performance specifications. Each data sheet describes the use of each user module parameter and documents the setting of each register controlled by the user module. The development process starts when you open a new project and bring up the Device Editor, a graphical user interface (GUI) for configuring the hardware. You pick the user modules you need for your project and map them onto the PSoC blocks with point-and-click simplicity. Next, you build signal chains by interconnecting user modules to each other and the IO pins. At this stage, you also configure the clock source connections and enter parameter values directly or by selecting values from drop-down menus. When you are ready to test the hardware configuration or move on to developing code for the project, you perform the "Generate Application" step. This causes PSoC Designer to generate source code that automatically configures the device to your specification and provides the high-level user module API functions. Figure 4. User Module/Source Code Development Flows Device Editor Designing with User Modules The development process for the PSoC device differs from that of a traditional fixed function microprocessor. The configurable analog and digital hardware blocks give the PSoC architecture a unique flexibility that pays dividends in managing specification change during development and by lowering inventory costs. These configurable resources, called PSoC Blocks, have the ability to implement a wide variety of user-selectable functions. Each block has several registers that determine its function and connectivity to other blocks, multiplexers, buses and to the IO pins. Iterative development cycles permit you to adapt the hardware and the software. This substantially lowers the risk of having to select a different part to meet the final design requirements. User Module Selection Document Number: 001-44369 Rev. *B Source Code Generator Generate Application Application Editor Project Manager To speed the development process, the PSoC Designer Integrated Development Environment (IDE) provides a library of pre-built, pre-tested hardware peripheral functions, called "User Modules." User modules make selecting and implementing peripheral devices simple, and come in analog, digital, and mixed signal varieties. The standard User Module library contains over 50 common peripherals such as ADCs, DACs Timers, Counters, UARTs, and other uncommon peripherals such as DTMF Generators and Bi-Quad analog filter sections. Each user module establishes the basic register settings that implement the selected function. It also provides parameters that allow you to tailor its precise configuration to your particular application. For example, a Pulse Width Modulator User Module configures one or more digital PSoC blocks, one for each 8 bits Placement and Parameter -ization Source Code Editor Build Manager Build All Debugger Interface to ICE Storage Inspector Event & Breakpoint Manager Page 6 of 37 [+] Feedback CY8C23433, CY8C23533 The next step is to write your main program, and any sub-routines using PSoC Designer's Application Editor subsystem. The Application Editor includes a Project Manager that allows you to open the project source code files (including all generated code files) from a hierarchal view. The source code editor provides syntax coloring and advanced edit features for both C and assembly language. File search capabilities include simple string searches and recursive "grep-style" patterns. A single mouse click invokes the Build Manager. It employs a professional-strength "makefile" system to automatically analyze all file dependencies and run the compiler and assembler as necessary. Project-level options control optimization strategies used by the compiler and linker. Syntax errors are displayed in a console window. Double clicking the error message takes you directly to the offending line of source code. When all is correct, the linker builds a HEX file image suitable for programming. The last step in the development process takes place inside the PSoC Designer's Debugger subsystem. The Debugger downloads the HEX image to the In-Circuit Emulator (ICE) where it runs at full speed. Debugger capabilities rival those of systems costing many times more. In addition to traditional single-step, run-to-breakpoint and watch-variable features, the Debugger provides a large trace buffer and allows you define complex breakpoint events that include monitoring address and data bus values, memory locations and external signals. Table 2. Acronyms Used (continued) Acronym Description PWM pulse width modulator RAM random access memory ROM read only memory SC switched capacitor Units of Measure A units of measure table is located in the section Electrical Specifications on page 14. Table 8 on page 14 lists all the abbreviations used to measure the PSoC devices. Numeric Naming Hexadecimal numbers are represented with all letters in uppercase with an appended lowercase `h' (for example, `14h' or `3Ah'). Hexadecimal numbers may also be represented by a `0x' prefix, the C coding convention. Binary numbers have an appended lowercase `b' (for example, 01010100b' or `01000011b'). Numbers not indicated by an `h' or `b' are decimal. Document Conventions Acronyms Used The following table lists the acronyms that are used in this document. Table 2. Acronyms Used Acronym Description AC alternating current ADC analog-to-digital converter API application programming interface CPU central processing unit CT continuous time DAC digital-to-analog converter DC direct current EEPROM electrically erasable programmable read-only memory FSR full scale range GPIO general purpose IO IO input/output IPOR imprecise power on reset LSb least-significant bit LVD low voltage detect MSb most-significant bit PC program counter POR power on reset PPOR precision power on reset PSoC(R) Programmable System-on-ChipTM Document Number: 001-44369 Rev. *B Page 7 of 37 [+] Feedback CY8C23433, CY8C23533 Pinouts The PSoC CY8C23X33 is available in 32-pin QFN and 28-pin SSOP packages. Every port pin (labeled with a "P"), except for Vss and Vdd in the following table and figure, is capable of Digital IO. 32-Pin Part Pinout Table 3. Pin Definitions - 32-Pin (QFN) IO 2 IO 3 IO I 4 IO I 5 IO AVref 6 P2[7] GPIO P2[5] GPIO P2[3] Direct Switched Capacitor Block Input P2[1] Direct Switched Capacitor Block Input P3[0][4] GPIO/ADC Vref (optional) NC 7 IO P1[7] 8 IO P1[5] 9 NC No Connection I2C Serial Clock (SCL) I2C Serial Data (SDA) No Connection 10 IO P1[3] GPIO 11 IO P1[1] GPIO, Crystal Input (XTALin), I2C Serial Clock (SCL), ISSP-SCLK* 12 Power Vss Ground Connection 13 IO P1[0] GPIO, Crystal Output (XTALout), I2C Serial Data (SDA), ISSP-SDATA* 14 IO P1[2] GPIO 15 IO P1[4] GPIO, External Clock IP IO P1[6] 16 17 NC 18 Input GPIO, P2[7] GPIO, P2[5] A, I, P2[3] A, I, P2[1] AVref, P3[0] NC I2C SCL, P1[7] I2C SDA, P1[5] 1 2 3 4 5 6 7 8 QFN (Top View) 24 23 22 21 20 19 18 17 P0[2], A, I P0[0], A, I P2[6], Vref P2[4], AGnd P2[2], A, I P2[0], A, I XRES P1[6], GPIO No Connection GPIO XRES Active High External Reset with Internal Pull Down 19 IO I 20 IO I 21 IO 22 IO P2[6] External Voltage Reference (VRef) 23 IO I P0[0] Analog Column Mux Input and ADC Input 24 IO I P0[2] Analog Column Mux Input and ADC Input 25 P2[0] Direct Switched Capacitor Block Input P2[2] Direct Switched Capacitor Block Input P2[4] External Analog Ground (AGnd) NC No Connection 26 IO I P0[4] Analog Column Mux Input and ADC Input 27 IO I P0[6] Analog Column Mux Input and ADC Input 28 Figure 5. CY8C23533 32-Pin PSoC Device P0[1], A, I P0[3], A, IO P0[5], A, IO P0[7], A, I Vdd P0[6], A, I P0[4], A, I NC 1 Description 32 31 30 29 28 27 26 25 Pin Digital Analog Name 9 10 11 12 13 14 15 16 Type NC GPIO P1[3] I2C SCL, XTALin, P1[1] Vss I2C SDA, XTALout, P1[0] GPIO P1[2] GPIO, EXTCLK, P1[4] NC Pin No. Vdd Supply Voltage 29 IO Power I P0[7] Analog Column Mux Input and ADC Input 30 IO IO P0[5] Analog Column Mux Input, Column Output and ADC Input 31 IO IO P0[3] Analog Column Mux Input, Column Output and ADC Input 32 IO I P0[1] Analog Column Mux Input.and ADC Input LEGEND: A = Analog, I = Input, and O = Output. Note 4. Even though P3[0] is an odd port, it resides on the left side of the pinout. Document Number: 001-44369 Rev. *B Page 8 of 37 [+] Feedback CY8C23433, CY8C23533 28-Pin Part Pinout IO 2 IO I IO Figure 6. CY8C23433 28-Pin PSoC Device Pin Name Digital 1 Analog Pin Number CY8C23433 Table 4. Pin Definitions - 28-Pin (SSOP) P0[7] P0[5] Description Analog Column Mux IP and ADC IP Analog Column Mux IP and Column O/P and ADC IP AIO, P0[7] 1 28 Vdd IO, P0[5] 2 27 P0[6], AIO, AnColMux and ADC IP IO, P0[3] 3 26 P0[4], AIO, AnColMux and ADC IP AIO, P0[1] 4 25 P0[2], AIO, AnColMux and ADC IP IO, P2[7] 5 24 P0[0], AIO, AnColMux and ADC IP IO, P2[5] 6 23 P2[6], VREF AIO, P2[3] 7 22 P2[4], AGND AIO, P2[1] 8 21 P2[2], AIO SSOP 3 IO IO P0[3] Analog Column Mux IP and Column O/P and ADC IP AVref, IO, P3[0] 9 20 P2[0], AIO I2C SCL, IO, P1[7] 10 19 P3[1], IO I2C SDA, IO, P1[5] 11 18 P1[6], IO 4 IO I P0[1] Analog Column Mux IP and ADC IP IO, P1[3] 12 17 P1[4], IO, EXTCLK 5 IO P2[7] GPIO I2C SCL,ISSP SCL,XTALin,IO, P1[1] 13 16 P1[2], IO Vss 14 15 P1[0],IO,XTALout,ISSP SDA,I2C SDA 6 IO P2[5] GPIO 7 IO I P2[3] Direct Switched Capacitor Input 8 IO I P2[1] Direct Switched Capacitor Input 9 IO AVref P3[0][5] GPIO/ADC Vref (optional) 10 IO P1[7] I2C SCL 11 IO P1[5] I2C SDA 12 IO P1[3] GPIO IO P1[1][6] GPIO, Xtal Input, I2C SCL, ISSP SCL 14 Power Vss Ground Pin 15 IO P1[0][6] GPIO, Xtal Output, I2C SDA, ISSP SDA 16 IO P1[2] GPIO 17 IO P1[4] GPIO, External Clock IP 18 IO P1[6] GPIO 19 IO P3[1][7] GPIO 20 IO I P2[0] Direct Switched Capacitor Input 21 IO I P2[2] Direct Switched Capacitor Input 22 IO P2[4] External Analog Ground (AGnd) 23 IO P2[6] Analog Voltage Reference (VRef) 24 IO I P0[0] Analog Column Mux IP and ADC IP 25 IO I P0[2] Analog Column Mux IP and ADC IP 26 IO I P0[4] Analog Column Mux IP and ADC IP 27 IO I P0[6] Analog Column Mux IP and ADC IP 28 Power Vdd Supply Voltage 13 LEGEND: A = Analog, I = Input, and O = Output. Notes 5. Even though P3[0] is an odd port, it resides on the left side of the pinout. 6. ISSP pin, which is not High Z at POR. 7. Even though P3[1] is an even port, it resides on the right side of the pinout. Document Number: 001-44369 Rev. *B Page 9 of 37 [+] Feedback CY8C23433, CY8C23533 Register Reference Register Mapping Tables This section lists the registers of the CY8C23433 PSoC device by using mapping tables, in offset order. Register Conventions Abbreviations Used The register conventions specific to this section are listed in the following table. The PSoC device has a total register address space of 512 bytes. The register space is referred to as IO space and is divided into two banks. The XOI bit in the Flag register (CPU_F) determines which bank the user is currently in. When the XOI bit is set the user is in Bank 1. Note In the following register mapping tables, blank fields are reserved and must not be accessed. Table 5. Abbreviations Convention R Description Read register or bits W Write register or bits L Logical register or bits C Clearable register or bits # Access is bit specific Document Number: 001-44369 Rev. *B Page 10 of 37 [+] Feedback CY8C23433, CY8C23533 DBB00DR0 DBB00DR1 DBB00DR2 DBB00CR0 DBB01DR0 DBB01DR1 DBB01DR2 DBB01CR0 DCB02DR0 DCB02DR1 DCB02DR2 DCB02CR0 DCB03DR0 DCB03DR1 DCB03DR2 DCB03CR0 Gray fields are reserved. # W RW # # W RW # # W RW # # W RW # AMX_IN ARF_CR CMP_CR0 ASY_CR CMP_CR1 SARADC_DL SARADC_CR0 SARADC_CR1 TMP_DR0 TMP_DR1 TMP_DR2 TMP_DR3 ACB00CR3 ACB00CR0 ACB00CR1 ACB00CR2 ACB01CR3 ACB01CR0 ACB01CR1 * ACB01CR2 * 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4E 4F 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5D 5E 5F 60 61 62 63 64 65 66 67 68 69 6A 6B 6C 6D 6E 6F 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D ASD11CR0 ASD11CR1 ASD11CR2 ASD11CR3 ASC21CR0 ASC21CR1 ASC21CR2 ASC21CR3 RW RW # # RW RW # RW RW RW RW RW RW RW RW RW RW RW RW RW RDI0RI RDI0SYN RDI0IS RDI0LT0 RDI0LT1 RDI0RO0 RDI0RO1 80 81 82 83 84 85 86 87 88 89 8A 8B 8C 8D 8E 8F 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9E 9F A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD RW RW RW RW RW RW RW RW I2C_CFG I2C_SCR I2C_DR I2C_MSCR INT_CLR0 INT_CLR1 INT_CLR3 INT_MSK3 INT_MSK0 INT_MSK1 INT_VC RES_WDT DEC_DH DEC_DL DEC_CR0 DEC_CR1 MUL0_X MUL0_Y MUL0_DH MUL0_DL ACC0_DR1 ACC0_DR0 ACC0_DR3 ACC0_DR2 RW RW RW RW RW RW RW CPU_F C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD Access Addr (0,Hex) Name Access Addr (0,Hex) Name RW RW RW RW RW RW RW RW RW RW RW RW RW RW RW RW Access Access 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D Addr (0,Hex) Addr (0,Hex) PRT0DR PRT0IE PRT0GS PRT0DM2 PRT1DR PRT1IE PRT1GS PRT1DM2 PRT2DR PRT2IE PRT2GS PRT2DM2 PRT3DR PRT3IE PRT3GS PRT3DM2 Name Name Table 6. Register Map Bank 0 Table: User Space RW # RW # RW RW RW RW RW RW RC W RC RC RW RW W W R R RW RW RW RW RL # Access is bit specific. Document Number: 001-44369 Rev. *B Page 11 of 37 [+] Feedback CY8C23433, CY8C23533 Gray fields are reserved. CPU_SCR1 CPU_SCR0 Access BE BF Name Access Addr (0,Hex) Name Access 7E 7F Addr (0,Hex) 3E 3F Addr (0,Hex) Name Access Addr (0,Hex) Name Table 6. Register Map Bank 0 Table: User Space (continued) FE FF # # # Access is bit specific. DBB00FN DBB00IN DBB00OU DBB01FN DBB01IN DBB01OU DCB02FN DCB02IN DCB02OU DCB03FN DCB03IN DCB03OU Gray fields are reserved. RW RW RW RW RW RW CLK_CR0 CLK_CR1 ABF_CR0 AMD_CR0 AMD_CR1 ALT_CR0 RW RW RW RW RW RW TMP_DR0 TMP_DR1 TMP_DR2 TMP_DR3 ACB00CR3 ACB00CR0 ACB00CR1 ACB00CR2 ACB01CR3 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4E 4F 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5D 5E 5F 60 61 62 63 64 65 66 67 68 69 6A 6B 6C 6D 6E 6F 70 71 72 73 74 ASD11CR0 ASD11CR1 ASD11CR2 ASD11CR3 ASC21CR0 ASC21CR1 ASC21CR2 ASC21CR3 RW RW RW RW RW RW RW RW RW RW RW RW RW RW RW SARADC_TRS SARADC_TRCL SARADC_TRCH SARADC_CR2 SARADC_LCR RDI0RI RDI0SYN RDI0IS RDI0LT0 RDI0LT1 80 81 82 83 84 85 86 87 88 89 8A 8B 8C 8D 8E 8F 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9E 9F A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF B0 B1 B2 B3 B4 RW RW RW RW GDI_O_IN GDI_E_IN GDI_O_OU GDI_E_OU RW RW RW RW OSC_GO_EN OSC_CR4 OSC_CR3 OSC_CR0 OSC_CR1 OSC_CR2 VLT_CR VLT_CMP RW RW RW # RW RW RW RW RW RW IMO_TR ILO_TR BDG_TR ECO_TR C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF F0 F1 F2 F3 F4 Access Addr (1,Hex) Name Access Addr (1,Hex) Name RW RW RW RW RW RW RW RW RW RW RW RW RW RW RW RW Access Access 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 Addr (1,Hex) Addr (1,Hex) PRT0DM0 PRT0DM1 PRT0IC0 PRT0IC1 PRT1DM0 PRT1DM1 PRT1IC0 PRT1IC1 PRT2DM0 PRT2DM1 PRT2IC0 PRT2IC1 PRT3DM0 PRT3DM1 PRT3IC0 PRT3IC1 Name Name Table 7. Register Map Bank 1 Table: Configuration Space RW RW RW RW RW RW RW RW RW RW RW R W W RW W # Access is bit specific. Document Number: 001-44369 Rev. *B Page 12 of 37 [+] Feedback CY8C23433, CY8C23533 Gray fields are reserved. FLS_PR1 F5 F6 F7 F8 F9 FA FB FC FD FE FF CPU_F CPU_SCR1 CPU_SCR0 Access RW RW Addr (1,Hex) B5 B6 B7 B8 B9 BA BB BC BD BE BF Name RDI0RO0 RDI0RO1 Access RW RW RW Addr (1,Hex) 75 76 77 78 79 7A 7B 7C 7D 7E 7F Name Access Name ACB01CR0 ACB01CR1 ACB01CR2 * Addr (1,Hex) 35 36 37 38 39 3A 3B 3C 3D 3E 3F Access Addr (1,Hex) Name Table 7. Register Map Bank 1 Table: Configuration Space (continued) RL RW # # # Access is bit specific. Document Number: 001-44369 Rev. *B Page 13 of 37 [+] Feedback CY8C23433, CY8C23533 Electrical Specifications This section presents the DC and AC electrical specifications of the CY8C23433 PSoC device. For the latest electrical specifications, visit http://www.cypress.com/psoc. Specifications are valid for -40C TA 85C and TJ 100C, except where noted. Refer to Table 24 on page 25 for the electrical specifications on the internal main oscillator (IMO) using SLIMO mode. Figure 7. Voltage versus CPU Frequency 5.25 SLIMO Mode = 0 Figure 8. IMO Frequency Trim Options 5.25 4.75 Vdd Voltage Vdd Voltage lid g Va ratin n pe io O Reg 4.75 SLIMO Mode=1 SLIMO Mode=0 SLIMO Mode=1 SLIMO Mode=0 3.60 3.00 3.00 93 kHz 12 MHz 3 MHz 93 kHz 24 MHz 6 MHz 12 MHz 24 MHz IMO Frequency CPU Frequency The following table lists the units of measure that are used in this section. Table 8. Units of Measure Symbol Unit of Measure Symbol Unit of Measure C degree Celsius W micro watts dB decibels mA milli-ampere fF femto farad ms milli-second Hz hertz mV milli-volts KB 1024 bytes nA nano ampere Kbit 1024 bits ns nanosecond kHz kilohertz nV nanovolts k kilohm W ohm MHz megahertz pA pico ampere M megaohm pF pico farad A micro ampere pp peak-to-peak F micro farad ppm H micro henry ps picosecond s microsecond sps samples per second V micro volts s sigma: one standard deviation micro volts root-mean-square V volts Vrms Document Number: 001-44369 Rev. *B parts per million Page 14 of 37 [+] Feedback CY8C23433, CY8C23533 Absolute Maximum Ratings Exceeding maximum ratings may shorten the useful life of the device. User guidelines are not tested. Table 9. Absolute Maximum Ratings Symbol Description Min Typ Max Units -55 25 +100 C Ambient Temperature with Power Applied -40 - +85 C Supply Voltage on Vdd Relative to Vss -0.5 - +6.0 V DC Input Voltage Vss - 0.5 - Vdd + 0.5 V DC Voltage Applied to Tri-state Vss - 0.5 - Vdd + 0.5 V TSTG Storage Temperature TA Vdd VIO VIOZ IMIO Maximum Current into any Port Pin ESD Electro Static Discharge Voltage LU Latch-up Current -25 - +50 mA 2000 - - V - - 200 mA Notes Higher storage temperatures reduce data retention time. Recommended storage temperature is +25C 25C. Extended duration storage temperatures above 65C degrade reliability. Human Body Model ESD. Operating Temperature Table 10. Operating Temperature Min Typ Max Units TA Symbol Ambient Temperature Description -40 - +85 C TJ Junction Temperature -40 - +100 C Document Number: 001-44369 Rev. *B Notes The temperature rise from ambient to junction is package specific. See Thermal Impedances by Package on page 35. The user must limit the power consumption to comply with this requirement. Page 15 of 37 [+] Feedback CY8C23433, CY8C23533 DC Electrical Characteristics DC Chip-Level Specifications The following table lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40C TA 85C, or 3.0V to 3.6V and -40C TA 85C, respectively. Typical parameters apply to 5V and 3.3V at 25C and are for design guidance only. Table 11. DC Chip-Level Specifications Symbol Description Vdd Supply Voltage Min 3.0 Typ - Max 5.25 IDD Supply Current - 5 8 IDD3 Supply Current - 3.3 6.0 ISB Sleep (Mode) Current with POR, LVD, Sleep Timer, and WDT.[8] - 3 6.5 ISBH Sleep (Mode) Current with POR, LVD, Sleep Timer, and WDT at high temperature.[8] - 4 25 ISBXTL Sleep (Mode) Current with POR, LVD, Sleep Timer, WDT, and external crystal.[8] - 4 7.5 ISBXTLH Sleep (Mode) Current with POR, LVD, Sleep Timer, WDT, and external crystal at high temperature.[8] - 5 26 VREF Reference Voltage (Bandgap) 1.28 1.30 1.33 Units Notes V See DC POR and LVD Specifications on page 22. mA Conditions are Vdd = 5.0V, TA = 25C, CPU = 3 MHz, SYSCLK doubler disabled, VC1 = 1.5 MHz, VC2 = 93.75 kHz, VC3 = 93.75 kHz, analog power = off. SLIMO mode = 0. IMO = 24 MHz. mA Conditions are Vdd = 3.3V, TA = 25C, CPU = 3 MHz, SYSCLK doubler disabled, VC1 = 1.5 MHz, VC2 = 93.75 kHz, VC3 = 93.75 kHz, analog power = off. SLIMO mode = 0. IMO = 24 MHz. A Conditions are with internal slow speed oscillator, Vdd = 3.3V, -40C TA 55C, analog power = off. A Conditions are with internal slow speed oscillator, Vdd = 3.3V, 55C < TA 85C, analog power = off. A Conditions are with properly loaded, 1 W max, 32.768 kHz crystal. Vdd = 3.3V, -40C TA 55C, analog power = off. A Conditions are with properly loaded, 1W max, 32.768 kHz crystal. Vdd = 3.3 V, 55C < TA 85C, analog power = off. V Trimmed for appropriate Vdd. Vdd > 3.0V Note 8. Standby current includes all functions (POR, LVD, WDT, Sleep Time) needed for reliable system operation. This must be compared with devices that have similar functions enabled. Document Number: 001-44369 Rev. *B Page 16 of 37 [+] Feedback CY8C23433, CY8C23533 DC General Purpose IO Specifications The following table lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40C TA 85C, or 3.0V to 3.6V and -40C TA 85C, respectively. Typical parameters apply to 5V and 3.3V at 25C and are for design guidance only. Table 12. 5V and 3.3V DC GPIO Specifications Symbol Description Min Typ Max Units Notes RPU Pull up Resistor 4 5.6 8 k RPD Pull down Resistor 4 5.6 8 k VOH High Output Level Vdd - 1.0 - - V IOH = 10 mA, Vdd = 4.75 to 5.25V (maximum 40 mA on even port pins (for example, P0[2], P1[4]), maximum 40 mA on odd port pins (for example, P0[3], P1[5])). 80 mA maximum combined IOH budget. VOL Low Output Level - - 0.75 V IOL = 25 mA, Vdd = 4.75 to 5.25V (maximum 100 mA on even port pins (for example, P0[2], P1[4]), maximum 100 mA on odd port pins (for example, P0[3], P1[5])). 100 mA maximum combined IOH budget. 0.8 V Vdd = 3.0 to 5.25 V Vdd = 3.0 to 5.25 VIL Input Low Level - - VIH Input High Level 2.1 - VH Input Hysterisis - 60 - mV IIL Input Leakage (Absolute Value) - 1 - nA Gross tested to 1 A CIN Capacitive Load on Pins as Input - 3.5 10 pF Package and pin dependent. Temp = 25C COUT Capacitive Load on Pins as Output - 3.5 10 pF Package and pin dependent. Temp = 25C Document Number: 001-44369 Rev. *B Page 17 of 37 [+] Feedback CY8C23433, CY8C23533 DC Operational Amplifier Specifications The following table lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40C TA 85C, or 3.0V to 3.6V and -40C TA 85C, respectively. Typical parameters apply to 5V and 3.3V at 25C and are for design guidance only. The Operational Amplifier is a component of both the Analog Continuous Time PSoC blocks and the Analog Switched Cap PSoC blocks. The guaranteed specifications are measured in the Analog Continuous Time PSoC block. Typical parameters apply to 5V at 25C and are for design guidance only. Table 13. 5V DC Operational Amplifier Specifications Symbol VOSOA Description Input Offset Voltage (absolute value) Power = Low, Opamp Bias = High Power = Medium, Opamp Bias = High Power = High, Opamp Bias = High TCVOSOA Average Input Offset Voltage Drift Min Typ Max Units - - - 1.6 1.3 1.2 10 8 7.5 mV mV mV - 7.0 35.0 V/C Notes IEBOA Input Leakage Current (Port 0 Analog Pins) - 20 - pA Gross tested to 1 A CINOA Input Capacitance (Port 0 Analog Pins) - 4.5 9.5 pF Package and pin dependent. Temp = 25C VCMOA Common Mode Voltage Range Common Mode Voltage Range (high power or high opamp bias) 0.0 - V 0.5 - Vdd Vdd - 0.5 The common-mode input voltage range is measured through an analog output buffer. The specification includes the limitations imposed by the characteristics of the analog output buffer. - - dB Specification is applicable at high power. For all other bias modes (except high power, high opamp bias), minimum is 60 dB. GOLOA Open Loop Gain Power = Low, Opamp Bias = High Power = Medium, Opamp Bias = High Power = High, Opamp Bias = High 60 60 80 VOHIGHOA High Output Voltage Swing (internal signals) Power = Low, Opamp Bias = High Power = Medium, Opamp Bias = High Power = High, Opamp Bias = High Vdd - 0.2 Vdd - 0.2 Vdd - 0.5 - - - - - - V V V VOLOWOA Low Output Voltage Swing (internal signals) Power = Low, Opamp Bias = High Power = Medium, Opamp Bias = High Power = High, Opamp Bias = High - - - - - - 0.2 0.2 0.5 V V V - - - - - 300 600 1200 2400 4600 400 800 1600 3200 6400 A A A A A 52 80 - dB ISOA Supply Current (including associated AGND buffer) Power = Low, Opamp Bias = High Power = Medium, Opamp Bias = Low Power = Medium, Opamp Bias = High Power = High, Opamp Bias = Low Power = High, Opamp Bias = High PSRROA Supply Voltage Rejection Ratio Document Number: 001-44369 Rev. *B Vss VIN (Vdd - 2.25) or (Vdd - 1.25V) VIN Vdd Page 18 of 37 [+] Feedback CY8C23433, CY8C23533 Table 14. 3.3V DC Operational Amplifier Specifications Symbol VOSOA Description Input Offset Voltage (absolute value) Power = Low, Opamp Bias = High Power = Medium, Opamp Bias = High High Power is 5 Volts Only TCVOSOA Average Input Offset Voltage Drift Min Typ Max Units - - 1.65 1.32 10 8 mV mV - 7.0 35.0 V/C Notes IEBOA Input Leakage Current (Port 0 Analog Pins) - 20 - pA Gross tested to 1 A. CINOA Input Capacitance (Port 0 Analog Pins) - 4.5 9.5 pF Package and pin dependent. Temp = 25C VCMOA Common Mode Voltage Range 0.2 - Vdd - 0.2 V The common-mode input voltage range is measured through an analog output buffer. The specification includes the limitations imposed by the characteristics of the analog output buffer. GOLOA Open Loop Gain Power = Low, Opamp Bias = Low Power = Medium, Opamp Bias = Low Power = High, Opamp Bias = Low - - dB 60 60 80 Specification is applicable at high power. For all other bias modes (except high power, high opamp bias), minimum is 60 dB. VOHIGHOA High Output Voltage Swing (internal signals) Power = Low, Opamp Bias = Low Power = Medium, Opamp Bias = Low Power = High is 5V only Vdd - 0.2 Vdd - 0.2 Vdd - 0.2 - - - - - - V V V VOLOWOA Low Output Voltage Swing (internal signals) Power = Low, Opamp Bias = Low Power = Medium, Opamp Bias = Low Power = High, Opamp Bias = Low - - - - - - 0.2 0.2 0.2 V V V ISOA Supply Current (including associated AGND buffer) Power = Low, Opamp Bias = High Power = Medium, Opamp Bias = Low Power = Medium, Opamp Bias = High Power = High, Opamp Bias = Low Power = High, Opamp Bias = High - - - - - 300 600 1200 2400 4600 400 800 1600 3200 6400 A A A A A PSRROA Supply Voltage Rejection Ratio 52 80 - dB Vss VIN (Vdd - 2.25) or (Vdd - 1.25V) VIN Vdd DC Low Power Comparator Specifications The following table lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40C TA 85C, or 3.0V to 3.6V and -40C TA 85C, respectively. Typical parameters apply to 5V and 3.3V at 25C and are for design guidance only. Table 15. DC Low Power Comparator Specifications Symbol Description Min Typ Max Units 0.2 - Vdd - 1 V VREFLPC Low power comparator (LPC) reference voltage range ISLPC LPC supply current - 10 40 A VOSLPC LPC voltage offset - 2.5 30 mV Document Number: 001-44369 Rev. *B Page 19 of 37 [+] Feedback CY8C23433, CY8C23533 DC Analog Output Buffer Specifications The following table lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40C TA 85C, or 3.0V to 3.6V and -40C TA 85C, respectively. Typical parameters apply to 5V and 3.3V at 25C and are for design guidance only. Table 16. 5V DC Analog Output Buffer Specifications Symbol VOSOB TCVOSOB VCMOB ROUTOB Description Min Input Offset Voltage (Absolute Value) - Average Input Offset Voltage Drift - Common-Mode Input Voltage Range 0.5 Output Resistance Power = Low - Power = High - VOHIGHOB High Output Voltage Swing (Load = 32 ohms to Vdd/2) Power = Low 0.5 x Vdd + 1.1 Power = High 0.5 x Vdd + 1.1 VOLOWOB Low Output Voltage Swing (Load = 32 ohms to Vdd/2) Power = Low - Power = High - ISOB Supply Current Including Bias Cell (No Load) Power = Low - Power = High - PSRROB Supply Voltage Rejection Ratio 52 Typ 3 +6 - Max 12 - Vdd - 1.0 Units mV V/C V Notes 1 1 - - W W - - - - V V - - 0.5 x Vdd - 1.3 0.5 x Vdd - 1.3 V V 1.1 2.6 64 5.1 8.8 - mA mA dB VOUT >(Vdd - 1.25) Min Typ Max Units Notes - 3 12 mV Table 17. 3.3V DC Analog Output Buffer Specifications Symbol VOSOB Description Input Offset Voltage (Absolute Value) - +6 - V/C 0.5 - Vdd - 1.0 V - - 1 1 - - W W VOHIGHOB High Output Voltage Swing (Load = 1k ohms to Vdd/2) Power = Low 0.5 x Vdd + 1.0 Power = High 0.5 x Vdd + 1.0 - - - - V V VOLOWOB Low Output Voltage Swing (Load = 1k ohms to Vdd/2) Power = Low Power = High - - - - 0.5 x Vdd - 1.0 0.5 x Vdd - 1.0 V V Supply Current Including Bias Cell (No Load) Power = Low Power = High - 0.8 2.0 2.0 4.3 mA mA Supply Voltage Rejection Ratio 52 64 - dB TCVOSOB Average Input Offset Voltage Drift VCMOB Common-Mode Input Voltage Range ROUTOB Output Resistance Power = Low Power = High ISOB PSRROB Document Number: 001-44369 Rev. *B VOUT > (Vdd - 1.25) Page 20 of 37 [+] Feedback CY8C23433, CY8C23533 DC Analog Reference Specifications The following table lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40C TA 85C, or 3.0V to 3.6V and -40C TA 85C, respectively. Typical parameters apply to 5V and 3.3V at 25C and are for design guidance only. The guaranteed specifications are measured through the Analog Continuous Time PSoC blocks. The power levels for AGND refer to the power of the Analog Continuous Time PSoC block. The power levels for RefHi and RefLo refer to the Analog Reference Control register. The limits stated for AGND include the offset error of the AGND buffer local to the Analog Continuous Time PSoC block. Reference control power is high. Table 18. 5V DC Analog Reference Specifications Symbol Description BG Bandgap Voltage Reference - AGND = Vdd/2 - AGND = 2 x BandGap - AGND = P2[4] (P2[4] = Vdd/2) - AGND = BandGap - AGND = 1.6 x BandGap - AGND Block to Block Variation (AGND = Vdd/2) - RefHi = Vdd/2 + BandGap - RefHi = 3 x BandGap - RefHi = 2 x BandGap + P2[6] (P2[6] = 1.3V) - RefHi = P2[4] + BandGap (P2[4] = Vdd/2) - RefHi = P2[4] + P2[6] (P2[4] = Vdd/2, P2[6] = 1.3V) - Min Typ Max Units 1.28 1.30 1.33 V Vdd/2 - 0.04 Vdd/2 - 0.01 Vdd/2 + 0.007 V 2 x BG - 0.048 2 x BG - 0.030 2 x BG + 0.024 V P2[4] - 0.011 P2[4] P2[4] + 0.011 V BG - 0.009 BG + 0.008 BG + 0.016 V 1.6 x BG - 0.022 1.6 x BG - 0.010 1.6 x BG + 0.018 V -0.034 0.000 0.034 V Vdd/2 + BG - 0.10 Vdd/2 + BG Vdd/2 + BG + 0.10 V 3 x BG - 0.06 3 x BG 3 x BG + 0.06 V 2 x BG + P2[6] - 0.113 2 x BG + P2[6] - 0.018 2 x BG + P2[6] + 0.077 V P2[4] + BG - 0.130 P2[4] + BG - 0.016 P2[4] + BG + 0.098 V P2[4] + P2[6] - 0.133 P2[4] + P2[6] - 0.016 P2[4] + P2[6]+ 0.100 V RefHi = 3.2 x BandGap 3.2 x BG - 0.112 3.2 x BG 3.2 x BG + 0.076 V - RefLo = Vdd/2 - BandGap Vdd/2 - BG - 0.04 Vdd/2 - BG + 0.024 Vdd/2 - BG + 0.04 V - RefLo = BandGap BG - 0.06 BG BG + 0.06 V - RefLo = 2 x BandGap - P2[6] (P2[6] = 1.3V) - RefLo = P2[4] - BandGap (P2[4] = Vdd/2) - RefLo = P2[4]-P2[6] (P2[4] = Vdd/2, P2[6] = 1.3V) 2 x BG - P2[6] - 0.084 2 x BG - P2[6] + 0.025 2 x BG - P2[6] + 0.134 V P2[4] - BG - 0.056 P2[4] - BG + 0.026 P2[4] - BG + 0.107 V P2[4] - P2[6] - 0.057 P2[4] - P2[6] + 0.026 P2[4] - P2[6] + 0.110 V Typ Max Units Table 19. 3.3V DC Analog Reference Specifications Symbol Description Min BG Bandgap Voltage Reference - AGND = Vdd/2 - AGND = 2 x BandGap - AGND = P2[4] (P2[4] = Vdd/2) - AGND = BandGap - AGND = 1.6 x BandGap - AGND Column to Column Variation (AGND = Vdd/2) - RefHi = Vdd/2 + BandGap Not Allowed - RefHi = 3 x BandGap Not Allowed Document Number: 001-44369 Rev. *B 1.28 1.30 1.33 V Vdd/2 - 0.03 Vdd/2 - 0.01 Vdd/2 + 0.005 V P2[4] - 0.008 P2[4] + 0.001 P2[4] + 0.009 V Not Allowed BG - 0.009 BG + 0.005 BG + 0.015 V 1.6 x BG - 0.027 1.6 x BG - 0.010 1.6 x BG + 0.018 V -0.034 0.000 0.034 mV Page 21 of 37 [+] Feedback CY8C23433, CY8C23533 Table 19. 3.3V DC Analog Reference Specifications (continued) Symbol Description Min Typ - RefHi = 2 x BandGap + P2[6] (P2[6] = 0.5V) - RefHi = P2[4] + BandGap (P2[4] = Vdd/2) - RefHi = P2[4] + P2[6] (P2[4] = Vdd/2, P2[6] = 0.5V) - RefHi = 3.2 x BandGap Not Allowed - RefLo = Vdd/2 - BandGap Not Allowed - RefLo = BandGap Not Allowed - RefLo = 2 x BandGap - P2[6] (P2[6] = 0.5V) Not Allowed - RefLo = P2[4] - BandGap (P2[4] = Vdd/2) - RefLo = P2[4]-P2[6] (P2[4] = Vdd/2, P2[6] = 0.5V) Max Units P2[4] + P2[6] + 0.057 V P2[4] - P2[6] + 0.092 V Not Allowed Not Allowed P2[4] + P2[6] - 0.075 P2[4] + P2[6] - 0.009 Not Allowed P2[4] - P2[6] - 0.048 P2[4]- P2[6] + 0.022 DC Analog PSoC Block Specifications The following table lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40C TA 85C, or 3.0V to 3.6V and -40C TA 85C, respectively. Typical parameters apply to 5V and 3.3V at 25C and are for design guidance only. Table 20. DC Analog PSoC Block Specifications Symbol RCT CSC Description Resistor Unit Value (Continuous Time) Capacitor Unit Value (Switch Cap) Min Typ Max Units - 12.2 - k - 80[9] - fF DC POR and LVD Specifications The following table lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40C TA 85C, or 3.0V to 3.6V and -40C TA 85C, respectively. Typical parameters apply to 5V and 3.3V at 25C and are for design guidance only. Note The bits PORLEV and VM in the following table refer to bits in the VLT_CR register. See the PSoC Mixed-Signal Array Technical Reference Manual for more information on the VLT_CR register. Table 21. DC POR and LVD Specifications Symbol Description VPPOR1 VPPOR2 Vdd Value for PPOR Trip PORLEV[1:0] = 01b PORLEV[1:0] = 10b VLVD1 VLVD2 VLVD3 VLVD4 VLVD5 VLVD6 VLVD7 Vdd Value for LVD Trip VM[2:0] = 001b VM[2:0] = 010b VM[2:0] = 011b VM[2:0] = 100b VM[2:0] = 101b VM[2:0] = 110b VM[2:0] = 111b Min Typ Max Units Notes Vdd must be greater than or equal to 2.5V during startup or reset from Watchdog. - 2.82 4.55 2.95 4.70 V V 2.850 2.95 3.06 4.37 4.50 4.62 4.71 2.920 3.02 3.13 4.48 4.64 4.73 4.81 2.99[10] 3.09 3.20 4.55 4.75 4.83 4.95 V0 V0 V0 V0 V0 V V Notes 9. CSC is a design guarantee parameter, not tested value 10. Always greater than 50 mV above VPPOR (PORLEV=01) for falling supply. Document Number: 001-44369 Rev. *B Page 22 of 37 [+] Feedback CY8C23433, CY8C23533 DC Programming Specifications The following table lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40C TA 85C, or 3.0V to 3.6V and -40C TA 85C, respectively. Typical parameters apply to 5V and 3.3V at 25C and are for design guidance only. Table 22. DC Programming Specifications Symbol Description VddIWRITE Supply Voltage for Flash Write Operations Min Typ Max Units Notes 2.7 - - V IDDP Supply Current During Programming or Verify - 5 25 mA VILP Input Low Voltage During Programming or Verify - - 0.8 V VIHP Input High Voltage During Programming or Verify 2.1 - - V IILP Input Current when Applying Vilp to P1[0] or P1[1] During Programming or Verify - - 0.2 mA Driving internal pull down resistor IIHP Input Current when Applying Vihp to P1[0] or P1[1] During Programming or Verify - - 1.5 mA Driving internal pull down resistor VOLV Output Low Voltage During Programming or Verify - - Vss + 0.75 V VOHV Output High Voltage During Programming or Verify Vdd - 1.0 - Vdd V FlashENPB Flash Endurance (per block) (total)[11] FlashENT Flash Endurance FlashDR Flash Data Retention 50,000 - - - Erase/write cycles per block 1,800,000 - - - Erase/write cycles 10 - - Years Note 11. A maximum of 36 x 50,000 block endurance cycles is allowed. This may be balanced between operations on 36x1 blocks of 50,000 maximum cycles each, 36x2 blocks of 25,000 maximum cycles each, or 36x4 blocks of 12,500 maximum cycles each (to limit the total number of cycles to 36x50,000 and that no single block ever sees more than 50,000 cycles). For the full industrial range, the user must employ a temperature sensor user module (FlashTemp) and feed the result to the temperature argument before writing. Refer to 0xthe Flash APIs Application Note AN2015 at http://www.cypress.com under Application Notes for more information. Document Number: 001-44369 Rev. *B Page 23 of 37 [+] Feedback CY8C23433, CY8C23533 SAR8 ADC DC Specifications The following table lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40C TA 85C, or 3.0V to 3.6V and -40C TA 85C, respectively. Typical parameters apply to 5V and 3.3V at 25C and are for design guidance only. Table 23. SAR8 ADC DC Specifications Symbol Description VADCVREF Reference voltage at pin P3[0] when configured as ADC reference voltage IADCVREF Current when P3[0] is configured as ADC VREF INL Integral Non-linearity INL (limited range) Integral Non-linearity accommodating a shift in the offset at 0x80 DNL Differential Non-linearity DNL (limited range) Differential Non-linearity excluding 0x7F-0x80 transition Min Typ Max Units Notes 3.0 - 5.25 V The voltage level at P3[0] (when configured as ADC reference voltage) must always be maintained to be less than chip supply voltage level on Vdd pin. VADCVREF < Vdd. 3 - - mA -1.5 - +1.5 LSB -1.2[12] - +1.2 LSB The maximum LSB is over a sub-range not exceeding 1/16 of the full-scale range. 0x7F and 0x80 points specs are excluded here -2.3 - +2.3 LSB ADC conversion is monotonic over full range -1 - +1 LSB ADC conversion is monotonic over full range. 0x7F to 0x80 transition specs are excluded here. Notes 12. SAR converters require a stable input voltage during the sampling period. If the voltage into the SAR8 changes by more than 1 LSB during the sampling period then the accuracy specifications may not be met Document Number: 001-44369 Rev. *B Page 24 of 37 [+] Feedback CY8C23433, CY8C23533 AC Electrical Characteristics AC Chip-Level Specifications The following table lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40C TA 85C, or 3.0V to 3.6V and -40C TA 85C, respectively. Typical parameters apply to 5V and 3.3V at 25C and are for design guidance only. Table 24. 5V and 3.3V AC Chip-Level Specifications Min Typ Max FIMO24 Symbol Internal Main Oscillator Frequency for 24 MHz 23.4 24 24.6[13],[14],[15] FIMO6 Internal Main Oscillator Frequency for 6 MHz 5.75 6 6.35[13],[14],[15] MHz Trimmed for 5V or 3.3V operation using factory trim values. See Figure 8 on page 14. SLIMO mode = 1. FCPU1 CPU Frequency (5V Nominal) 0.093 24 24.6[13],[14] MHz 12 [13],[14] MHz FCPU2 Description CPU Frequency (3.3V Nominal) 0.093 12.3 [13],[14],[16] Units Notes MHz Trimmed for 5V or 3.3V operation using factory trim values. See Figure 8 on page 14. SLIMO mode = 0. F48M Digital PSoC Block Frequency 0 48 F24M Digital PSoC Block Frequency 0 24 24.6[14],[16] MHz F32K1 Internal Low Speed Oscillator Frequency 15 32 75 kHz F32K2 External Crystal Oscillator - 32.768 - kHz FPLL PLL Frequency - 23.986 - MHz Is a multiple (x732) of crystal frequency. Jitter24M2 24 MHz Period Jitter (PLL) - - 600 ps TPLLSLEW PLL Lock Time 0.5 - 10 ms 0.5 - 50 ms TPLLSLEWSLOW PLL Lock Time for Low Gain Setting 49.2 MHz Refer to the AC Digital Block Specifications. TOS External Crystal Oscillator Startup to 1% - 1700 2620 ms TOSACC External Crystal Oscillator Startup to 100 ppm - 2800 3800 ms Jitter32k 32 kHz Period Jitter - 100 TXRST External Reset Pulse Width 10 - - s DC24M 24 MHz Duty Cycle 40 50 60 % Step24M 24 MHz Trim Step Size - 50 - kHz Fout48M 48 MHz Output Frequency 46.8 48.0 49.2[13],[15] Jitter24M1R 24 MHz Period Jitter (IMO) Root Mean Squared - - 600 ps FMAX Maximum frequency of signal on row input or row output. - - 12.3 MHz TRAMP Supply Ramp Time 0 - - s Accuracy is capacitor and crystal dependent. 50% duty cycle. The crystal oscillator frequency is within 100 ppm of its final value by the end of the Tosacc period. Correct operation assumes a properly loaded 1 uW maximum drive level 32.768 kHz crystal. 3.0V Vdd 5.5V, -40 C TA 85C. ns MHz Trimmed. Using factory trim values. Notes 13. 4.75V < Vdd < 5.25V. 14. Accuracy derived from Internal Main Oscillator with appropriate trim for Vdd range. 15. 3.0V < Vdd < 3.6V. See Application Note AN2012 "Adjusting PSoC Microcontroller Trims for Dual Voltage-Range Operation" for information on trimming for operation at 3.3V. 16. See the individual user module data sheets for information on maximum frequencies for user modules. Document Number: 001-44369 Rev. *B Page 25 of 37 [+] Feedback CY8C23433, CY8C23533 Figure 9. PLL Lock Timing Diagram PLL Enable TPLLSLEW 24 MHz FPLL PLL Gain 0 Figure 10. PLL Lock for Low Gain Setting Timing Diagram PLL Enable TPLLSLEWLOW 24 MHz FPLL PLL Gain 1 Figure 11. External Crystal Oscillator Startup Timing Diagram 32K Select 32 kHz TOS F32K2 Figure 12. 24 MHz Period Jitter (IMO) Timing Diagram Jitter24M1 F 24M Figure 13. 32 kHz Period Jitter (ECO) Timing Diagram Jitter32k F 32K2 Document Number: 001-44369 Rev. *B Page 26 of 37 [+] Feedback CY8C23433, CY8C23533 AC General Purpose IO Specifications The following table lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40C TA 85C, or 3.0V to 3.6V and -40C TA 85C, respectively. Typical parameters apply to 5V and 3.3V at 25C and are for design guidance only. Table 25. 5V and 3.3V AC GPIO Specifications Symbol Description Min Typ Max Units Notes FGPIO GPIO Operating Frequency 0 - 12.3 MHz TRiseF Rise Time, Normal Strong Mode, Cload = 50 pF 3 - 18 ns Vdd = 4.5 to 5.25V, 10% - 90% Normal Strong Mode TFallF Fall Time, Normal Strong Mode, Cload = 50 pF 2 - 18 ns Vdd = 4.5 to 5.25V, 10% - 90% TRiseS Rise Time, Slow Strong Mode, Cload = 50 pF 10 27 - ns Vdd = 3 to 5.25V, 10% - 90% TFallS Fall Time, Slow Strong Mode, Cload = 50 pF 10 22 - ns Vdd = 3 to 5.25V, 10% - 90% Figure 14. GPIO Timing Diagram 90% GPIO Pin Output Voltage 10% TRiseF TRiseS TFallF TFallS AC Operational Amplifier Specifications The following table lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40C TA 85C, or 3.0V to 3.6V and -40C TA 85C, respectively. Typical parameters apply to 5V and 3.3V at 25C and are for design guidance only. Settling times, slew rates, and gain bandwidth are based on the Analog Continuous Time PSoC block. Power = High and Opamp Bias = High is not supported at 3.3V. Table 26. 5V AC Operational Amplifier Specifications Symbol Description Min Typ Max Units TROA Rising Settling Time from 80% of V to 0.1% of V (10 pF load, Unity Gain) Power = Low, Opamp Bias = Low Power = Medium, Opamp Bias = High Power = High, Opamp Bias = High - - - - - - 3.9 0.72 0.62 s s s TSOA Falling Settling Time from 20% of V to 0.1% of V (10 pF load, Unity Gain) Power = Low, Opamp Bias = Low Power = Medium, Opamp Bias = High Power = High, Opamp Bias = High - - - - - - 5.9 0.92 0.72 s s s SRROA Rising Slew Rate (20% to 80%)(10 pF load, Unity Gain) Power = Low, Opamp Bias = Low Power = Medium, Opamp Bias = High Power = High, Opamp Bias = High 0.15 1.7 6.5 - - - - - - V/s V/s V/s SRFOA Falling Slew Rate (20% to 80%)(10 pF load, Unity Gain) Power = Low, Opamp Bias = Low Power = Medium, Opamp Bias = High Power = High, Opamp Bias = High 0.01 0.5 4.0 - - - - - - V/s V/s V/s BWOA Gain Bandwidth Product Power = Low, Opamp Bias = Low Power = Medium, Opamp Bias = High Power = High, Opamp Bias = High 0.75 3.1 5.4 - - - - - - MHz MHz MHz Document Number: 001-44369 Rev. *B Page 27 of 37 [+] Feedback CY8C23433, CY8C23533 Table 27. 3.3V AC Operational Amplifier Specifications Symbol TROA TSOA SRROA SRFOA BWOA Description Rising Settling Time from 80% of V to 0.1% of V (10 pF load, Unity Gain) Power = Low, Opamp Bias = Low Power = Medium, Opamp Bias = High Falling Settling Time from 20% of V to 0.1% of V (10 pF load, Unity Gain) Power = Low, Opamp Bias = Low Power = Medium, Opamp Bias = High Rising Slew Rate (20% to 80%)(10 pF load, Unity Gain) Power = Low, Opamp Bias = Low Power = Medium, Opamp Bias = High Falling Slew Rate (20% to 80%)(10 pF load, Unity Gain) Power = Low, Opamp Bias = Low Power = Medium, Opamp Bias = High Gain Bandwidth Product Power = Low, Opamp Bias = Low Power = Medium, Opamp Bias = High Document Number: 001-44369 Rev. *B Min Typ Max Units - - - - 3.92 0.72 s s - - - - 5.41 0.72 s s 0.31 2.7 - - - - V/s V/s 0.24 1.8 - - - - V/s V/s 0.67 2.8 - - - - MHz MHz Page 28 of 37 [+] Feedback CY8C23433, CY8C23533 When bypassed by a capacitor on P2[4], the noise of the analog ground signal distributed to each block is reduced by a factor of up to 5 (14 dB). This is at frequencies above the corner frequency defined by the on-chip 8.1k resistance and the external capacitor. Figure 15. Typical AGND Noise with P2[4] Bypass dBV/rtHz 10000 0 0.01 0.1 1.0 10 1000 100 0.001 0.01 0.1 Freq (kHz) 1 10 100 At low frequencies, the opamp noise is proportional to 1/f, power independent, and determined by device geometry. At high frequencies, increased power level reduces the noise spectrum level. Figure 16. Typical Opamp Noise nV/rtHz 10000 PH_BH PH_BL PM_BL PL_BL 1000 100 10 0.001 Document Number: 001-44369 Rev. *B 0.01 0.1 Freq (kHz) 1 10 100 Page 29 of 37 [+] Feedback CY8C23433, CY8C23533 AC Low Power Comparator Specifications The following table lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40C TA 85C, or 3.0V to 3.6V and -40C TA 85C, respectively. Typical parameters apply to 5V and 3.3V at 25C and are for design guidance only. Table 28. AC Low Power Comparator Specifications Symbol TRLPC Description LPC response time Min - Typ - Max 50 Units s Notes 50 mV overdrive comparator reference set within VREFLPC AC Digital Block Specifications The following table lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40C TA 85C, or 3.0V to 3.6V and -40C TA 85C, respectively. Typical parameters apply to 5V and 3.3V at 25C and are for design guidance only. Table 29. 5V and 3.3V AC Digital Block Specifications Symbol Min Typ Max Units 50[17] - - ns Maximum Frequency, No Capture - - 49.2 MHz Maximum Frequency, With Capture - - 24.6 MHz 50[17] - - ns Maximum Frequency, No Enable Input - - 49.2 MHz Maximum Frequency, Enable Input - - 24.6 MHz Asynchronous Restart Mode 20 - - ns Synchronous Restart Mode 50[17] - - ns Disable Mode 50[17] - - ns Maximum Frequency - - 49.2 MHz 4.75V < Vdd < 5.25V CRCPRS (PRS Mode) Maximum Input Clock Frequency - - 49.2 MHz 4.75V < Vdd < 5.25V CRCPRS (CRC Mode) Maximum Input Clock Frequency - - 24.6 MHz SPIM Maximum Input Clock Frequency - - 8.2 MHz SPIS Maximum Input Clock Frequency - - 4.1 MHz Width of SS_ Negated Between Transmissions 50[17] - - ns - - 24.6 MHz Maximum Input Clock Frequency with Vdd 4.75V, 2 Stop Bits - - 49.2 MHz Maximum Input Clock Frequency - - 24.6 MHz Maximum Input Clock Frequency with Vdd 4.75V, 2 Stop Bits - - 49.2 MHz Timer Counter Description Capture Pulse Width Enable Pulse Width Notes 4.75V < Vdd < 5.25V 4.75V < Vdd < 5.25V Dead Band Kill Pulse Width: Transmitter Maximum Input Clock Frequency Receiver Maximum data rate at 4.1 MHz due to 2 x over clocking. Maximum data rate at 3.08 MHz due to 8 x over clocking. Maximum data rate at 6.15 MHz due to 8 x over clocking. Maximum data rate at 3.08 MHz due to 8 x over clocking. Maximum data rate at 6.15 MHz due to 8 x over clocking. Note 17. 50 ns minimum input pulse width is based on the input synchronizers running at 24 MHz (42 ns nominal period). Document Number: 001-44369 Rev. *B Page 30 of 37 [+] Feedback CY8C23433, CY8C23533 AC Analog Output Buffer Specifications The following table lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40C TA 85C, or 3.0V to 3.6V and -40C TA 85C, respectively. Typical parameters apply to 5V and 3.3V at 25C and are for design guidance only. Table 30. 5V AC Analog Output Buffer Specifications Symbol Description Min Typ Max Units TROB Rising Settling Time to 0.1%, 1V Step, 100 pF Load Power = Low Power = High - - - - 2.5 2.5 s s TSOB Falling Settling Time to 0.1%, 1V Step, 100 pF Load Power = Low Power = High - - - - 2.2 2.2 s s SRROB Rising Slew Rate (20% to 80%), 1V Step, 100 pF Load Power = Low Power = High 0.65 0.65 - - - - V/s V/s SRFOB Falling Slew Rate (80% to 20%), 1V Step, 100 pF Load Power = Low Power = High 0.65 0.65 - - - - V/s V/s BWOB Small Signal Bandwidth, 20mVpp, 3 dB BW, 100 pF Load Power = Low Power = High 0.8 0.8 - - - - MHz MHz BWOB Large Signal Bandwidth, 1Vpp, 3 dB BW, 100 pF Load Power = Low Power = High 300 300 - - - - kHz kHz Min Typ Max Units Table 31. 3.3V AC Analog Output Buffer Specifications Symbol Description TROB Rising Settling Time to 0.1%, 1V Step, 100 pF Load Power = Low Power = High - - - - 3.8 3.8 s s TSOB Falling Settling Time to 0.1%, 1V Step, 100 pF Load Power = Low Power = High - - - - 2.6 2.6 s s SRROB Rising Slew Rate (20% to 80%), 1V Step, 100 pF Load Power = Low Power = High 0.5 0.5 - - - - V/s V/s SRFOB Falling Slew Rate (80% to 20%), 1V Step, 100 pF Load Power = Low Power = High 0.5 0.5 - - - - V/s V/s BWOB Small Signal Bandwidth, 20mVpp, 3 dB BW, 100 pF Load Power = Low Power = High 0.7 0.7 - - - - MHz MHz BWOB Large Signal Bandwidth, 1Vpp, 3 dB BW, 100 pF Load Power = Low Power = High 200 200 - - - - kHz kHz Document Number: 001-44369 Rev. *B Page 31 of 37 [+] Feedback CY8C23433, CY8C23533 AC External Clock Specifications The following table lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40C TA 85C, or 3.0V to 3.6V and -40C TA 85C, respectively. Typical parameters apply to 5V and 3.3V at 25C and are for design guidance only. Table 32. 5V AC External Clock Specifications Symbol Description Min Typ Max Units FOSCEXT Frequency 0.093 - 24.6 MHz - High Period 20.6 - 5300 ns - Low Period 20.6 - - ns - Power Up IMO to Switch 150 - - s Table 33. 3.3V AC External Clock Specifications Symbol Description Min Typ Max Units 0.093 - 12.3 MHz Frequency with CPU Clock divide by 2 or greater[19] 0.186 - 24.6 MHz - High Period with CPU Clock divide by 1 41.7 - 5300 ns - Low Period with CPU Clock divide by 1 41.7 - - ns - Power Up IMO to Switch 150 - - s FOSCEXT Frequency with CPU Clock divide by FOSCEXT 1[18] AC Programming Specifications The following table lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40C TA 85C, or 3.0V to 3.6V and -40C TA 85C, respectively. Typical parameters apply to 5V and 3.3V at 25C and are for design guidance only. Table 34. AC Programming Specifications Symbol Description Min Typ Max Units Notes TRSCLK Rise Time of SCLK 1 - 20 ns TFSCLK Fall Time of SCLK 1 - 20 ns TSSCLK Data Set up Time to Falling Edge of SCLK 40 - - ns THSCLK Data Hold Time from Falling Edge of SCLK 40 - - ns FSCLK Frequency of SCLK 0 - 8 MHz TERASEB Flash Erase Time (Block) - 20 - ms TWRITE Flash Block Write Time - 20 - ms TDSCLK Data Out Delay from Falling Edge of SCLK - - 45 ns Vdd > 3.6 TDSCLK3 Data Out Delay from Falling Edge of SCLK - - 50 ns 3.0 Vdd 3.6 SAR8 ADC AC Specifications The following table lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40C TA 85C, or 3.0V to 3.6V and -40C TA 85C, respectively. Typical parameters apply to 5V and 3.3V at 25C and are for design guidance only. Table 35. SAR8 ADC AC Specifications[20] Symbol Description Min Typ Max Units Freq3 Input clock frequency 3V - - 3.075 MHz Freq5 Input clock frequency 5V - - 3.075 MHz Notes 18. Maximum CPU frequency is 12 MHz at 3.3V. With the CPU clock divider set to 1, the external clock must adhere to the maximum frequency and duty cycle requirements. 19. If the frequency of the external clock is greater than 12 MHz, the CPU clock divider must be set to 2 or greater. In this case, the CPU clock divider ensures that the fifty percent duty cycle requirement is met. 20. The max sample rate in this R2R ADC is 3.0/8=375KSPS Document Number: 001-44369 Rev. *B Page 32 of 37 [+] Feedback CY8C23433, CY8C23533 AC I2C Specifications The following table lists the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40C TA 85C, or 3.0V to 3.6V and -40C TA 85C, respectively. Typical parameters apply to 5V and 3.3V at 25C and are for design guidance only. Table 36. AC Characteristics of the I2C SDA and SCL Pins for Vdd > 3.0V Symbol Standard Mode Description Min Max Fast Mode Min Max Units FSCLI2C SCL Clock Frequency 0 100 0 400 kHz THDSTAI2C Hold Time (repeated) START Condition. After this period, the first clock pulse is generated. 4.0 - 0.6 - s TLOWI2C LOW Period of the SCL Clock 4.7 - 1.3 - s THIGHI2C HIGH Period of the SCL Clock 4.0 - 0.6 - s TSUSTAI2C Setup Time for a Repeated START Condition 4.7 - 0.6 - s 0 - s - ns - s THDDATI2C Data Hold Time 0 - 250 - TSUSTOI2C Setup Time for STOP Condition 4.0 - 0.6 TBUFI2C Bus Free Time Between a STOP and START Condition 4.7 - 1.3 - s TSPI2C Pulse Width of spikes are suppressed by the input filter. - - 0 50 ns TSUDATI2C Data Setup Time 100 [21] Table 37. AC Characteristics of the I2C SDA and SCL Pins for Vdd < 3.0V (Fast Mode Not Supported) Symbol Standard Mode Description Fast Mode Units Min Max Min Max 0 100 - - kHz 4.0 - - - s FSCLI2C SCL Clock Frequency THDSTAI2C Hold Time (repeated) START Condition. After this period, the first clock pulse is generated. TLOWI2C LOW Period of the SCL Clock 4.7 - - - s THIGHI2C HIGH Period of the SCL Clock 4.0 - - - s TSUSTAI2C Setup Time for a Repeated START Condition 4.7 - - - s 0 - - - s THDDATI2C Data Hold Time TSUDATI2C 250 - - - ns TSUSTOI2C Setup Time for STOP Condition Data Setup Time 4.0 - - - s TBUFI2C Bus Free Time Between a STOP and START Condition 4.7 - - - s TSPI2C Pulse Width of spikes are suppressed by the input filter. - - - - ns Figure 17. Definition for Timing for Fast/Standard Mode on the I2C Bus SDA TLOWI2C TSUDATI2C THDSTAI2C TSPI2C TBUFI2C SCL S THDSTAI2C THDDATI2C THIGHI2C TSUSTAI2C Sr TSUSTOI2C P S Note 21. A Fast-Mode I2C-bus device can be used in a Standard-Mode I2C-bus system, but the requirement tSU;DAT 250 ns must then be met. This is automatically the case if the device does not stretch the LOW period of the SCL signal. If such device does stretch the LOW period of the SCL signal, it must output the next data bit to the Figure 18. I2C-bus specification) before the SCL line is released. SDA line trmax + tSU;DAT = 1000 + 250 = 1250 ns (according to the Standard-Mode Document Number: 001-44369 Rev. *B Page 33 of 37 [+] Feedback CY8C23433, CY8C23533 Packaging Information This section illustrates the packaging specifications for the CY8C23x33 PSoC device, along with the thermal impedances for each package, solder reflow peak temperature, and the typical package capacitance on crystal pins. Figure 19. 32-Pin (5x5 mm) QFN SEE NOTE 1 TOP VIEW BOTTOM VIEW SIDE VIEW NOTES: 1. HATCH AREA IS SOLDERABLE EXPOSED PAD CYPRESS COMPANY CONFIDENTIAL 2. BASED ON REF JEDEC # MO-248 3. PACKAGE WEIGHT: 0.0388g 4. DIMENSIONS ARE IN MILLIMETERS Document Number: 001-44369 Rev. *B TITLE 32L QFN 5 X 5 X 0.55 MM PACKAGE OUTLINE 3.5 X 3.5 EPAD (SAWN TYPE) SIZE PART NO. A LQ32 001-42168 *C DWG NO 001-42168 REV *C Page 34 of 37 [+] Feedback CY8C23433, CY8C23533 Figure 20. 28-Pin (210-Mil) SSOP 51-85079 *C Thermal Impedances Capacitance on Crystal Pins Table 38. Thermal Impedances by Package Table 39. Typical Package Capacitance on Crystal Pins Typical JA[22] Package 32 QFN 28 SSOP Package Package Capacitance 19.4C/W 32 QFN 2.0 pF 95C/W 28 SSOP 2.8 pF Solder Reflow Peak Temperature Following is the minimum solder reflow peak temperature to achieve good solderability. Table 40. Solder Reflow Peak Temperature Package Minimum Peak Temperature [23] Maximum Peak Temperature 32 QFN 240C 260C 28 SSOP 240C 260C Notes 22. TJ = TA + POWER x JA. 23. Higher temperatures may be required based on the solder melting point. Typical temperatures for solder are 220 5oC with Sn-Pb or 245 5oC with Sn-Ag-Cu paste. Refer to the solder manufacturer specifications. Document Number: 001-44369 Rev. *B Page 35 of 37 [+] Feedback CY8C23433, CY8C23533 Ordering Information The following table lists the CY8C23X33 PSoC device family key package features and ordering codes. Document Number: 001-44369 Rev. *B Digital IO Pins Analog Inputs Analog Outputs XRES Pin -40C to +85C -40C to +85C -40C to +85C -40C to +85C Analog Blocks (Columns of 3) 256 256 256 256 Temperature Range 8 8 8 8 Digital Blocks (Rows of 4) CY8C23533-24LQXI CY8C23533-24LQXIT CY8C23433-24PVXI CY8C23433-24PVXIT RAM (Bytes) 32 Pin QFN 32 Pin QFN (Tape and Reel) 28 Pin (210 Mil) SSOP 28 Pin (210 Mil) SSOP (Tape and Reel) Flash (Kbytes) Package Ordering Code Table 41. CY8C23X33 PSoC Device Family Key Features and Ordering Information 4 4 4 4 4 4 4 4 26 26 26 26 12 12 12 12 2 2 2 2 Yes Yes No No Page 36 of 37 [+] Feedback CY8C23433, CY8C23533 Document History Page Document Title: CY8C23433, CY8C23533 PSoC(R) Programmable System-on-ChipTM Document Number: 001-44369 Revision ECN Orig. of Change Submission Date Description of Change ** 2044848 KIY/AESA 01/30/2008 Data sheet creation *A 2482967 HMI/AESA 05/14/2008 Moved from Preliminary to Final. Part number changed to CY8C23433, CY8C23533. Adjusted placement of the block diagram; updated description of DAC; updated package pinout description, updated POR and LVD spec, Added Csc , Flash Vdd, SAR ADC spec. Updated package diagram 001-42168 to *A. Updated data sheet template. *B 2616862 OGNE/AESA 12/05/2008 Changed title to: "CY8C23433, CY8C23533 PSoC(R) Programmable System-on-ChipTM" Updated package diagram 001-42168 to *C. Changed names of registers on page 11. "SARADC_C0" to "SARADC_CR0" "SARADC_C1" to "SARADC_CR1" Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer's representatives, and distributors. To find the office closest to you, visit us at cypress.com/sales. Products PSoC Solutions PSoC psoc.cypress.com Clocks & Buffers clocks.cypress.com General Low Power/Low Voltage psoc.cypress.com/solutions psoc.cypress.com/low-power Wireless wireless.cypress.com Precision Analog Memories memory.cypress.com LCD Drive psoc.cypress.com/lcd-drive image.cypress.com CAN 2.0b psoc.cypress.com/can USB psoc.cypress.com/usb Image Sensors psoc.cypress.com/precision-analog (c) Cypress Semiconductor Corporation, 2008. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign), United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of, and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without the express written permission of Cypress. Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress' product in a life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Use may be limited by and subject to the applicable Cypress software license agreement. Document Number: 001-44369 Rev. *B Revised December 05, 2008 Page 37 of 37 PSoC DesignerTM, Programmable System-on-ChipTM, and PSoC ExpressTM are trademarks and PSoC(R) is a registered trademark of Cypress Semiconductor Corp. All other trademarks or registered trademarks referenced herein are property of the respective corporations. Purchase of I2C components from Cypress or one of its sublicensed Associated Companies conveys a license under the Philips I2C Patent Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specification as defined by Philips. All products and company names mentioned in this document may be the trademarks of their respective holders. [+] Feedback