PRELIMINARY DATA SHEET | OCTOBER 28, 2007 PONA 3000 Series Erbium Doped Fiber Amplifier Applications * High Performance Supertrunking Links * High Power Distribution Networks * Fiber Deep Architectures * FTTx Networks Features * Full Function High Power Fiber Optic Amplifier Ready for Integration * Low Noise Figure (Typ < 6 dB) * Total Input Power Range: -10 dBm to * The ORTEL PONA 3000 Series Fiber Optical Amplifier Module is an +12 dBm ideal building block for OEM system integrators. The family of PONA Total Output Power: +27 dBm to 3000 Optical Amplifiers is designed to meet the most demanding +35 dBm (Optical Output Power noise performance requirements of CATV and FTTx applications, and Splitter is Optional For These Units) performs all the functions required of an optical amplifier for system * Standard RS-232 Communications * Low Electrical Power Consumption * Input / Output Isolation > 40/40 dB isolation on the input and output of the gain block for stable, low noise * Polarization Dependant Gain < 0.1 dB operation. * Polarization Mode Dispersion < 0.5 ps detected for monitoring and control. integration. PONA 3000 series optical amplifiers provide optical The input and output optical signal power levels are The input optical signal is amplified with active gain control for a constant output power level, or with active output power control for constant gain mode. The PONA 3000 series optical amplifiers also provide monitoring functions and associated alarms for all vital characteristics. The optical output of the PONA 3000 series optical amplifiers can be split into number of ports by an optional internal splitter. PONA3000 series includes AC/DC power supply, front panel, optical splitters, network card and all necessary connectors. 1 of 6 For more information on this and other products: Contact Sales at Emcore 626-293-3400, or visit www.emcore.com. PONA3000 Series High Power EDFA PRELIMINARY DATA SHEET | OCTOBER 28, 2007 Specifications PROPERTY Product Code PERFORMANCE Operating Input Power Operating Input Power Output Power Noise Figure Static Gain Flatness Dynamic Gain Flatness Output Power Stability Power Consumption (steady state regime) Remnant pump power to output UNIT LIMIT PONA MODELS 3030 3032 3027 COMMENT 3035 (note 1) Pin (dBm) Pin (dBm) Po (dBm) NF (dB) GF (dB) (dB) (dB) Psys (W) Max Min Prp (dBm) Nom. Typ/Max Max Max Max Max +12 -10 27.0 5.5/6.0 +/-1.0 +/-2.00 +/- 0.25 40 25 +12 -10 30.0 5.5/6.0 +/-1.0 +/-2.00 +/- 0.25 50 30 +12 -10 32.0 5.5/6.0 +/-1.0 +/-2.25 +/-0.25 65 40 +12 -10 35.0 5.5/6.0 +/-1.0 +/-2.50 +/- 0.25 80 50 <-30 <-30 <-30 <-30 Nominal (note 2) (note 3) (note 4) (note 5) (note 6) o 50 C Case (premium) o 50 C Case (economy) (note7) Notes: 1) Unless stated otherwise all specifications apply over the full temperature range and humidity 2) Depending on the fiber optic patchcord interface the measured value can vary up to 0.5 dB less than the actual value 3) Measured @ 25C, Pin = 0 dBm 4) Measured with a swept Probe Signal (Pp), where Pp = 0 dBm @ 25C 5) Measured with a swept Probe Signal (Pp), and a fixed Tone Signal (Pt) @ 1553nm; (Pt = Pp+20 dB; Pt + Pp = 0 dBm) @ 25C 6) Stability over polarization and temperature 7) Premium version - PONA with cooled, Telcordia qualified pumps Economy version - PONA with uncooled pumps Physical GENERAL PROPERTY Operating Wavelength Operating Case Temperature Storage Temperature Operating Humidity Voltage Supply Range REQUIREMENT COMMENTS 1545 ~ 1562nm Standard 0C to 50C -40C to 85C 20% to 85% 85 VAC to 265 VAC 50/60 Hz Standard Standard Non-condensing AC version -36 to -60 V DC DC version *(Redundant Power Supply is Available by Customer Request) Optical Connectors Dimensions In Inches See ordering information 19.0"W x 14.76"D x 3.44"H User Specified 19'' Rack Mounted, 2 RU 2 of 6 Ortel, a division of EMCORE 2015 West Chestnut Street Alhambra, California 91803-1542 Tel: 626-293-3400 Fax: 626-293-3428 www.emcore.com Copyright 2007. EMCORE Corporation PONA3000 Series High Power EDFA PRELIMINARY DATA SHEET | OCTOBER 28, 2007 Block Diagram: Cladding Pump Technology Cladding pump technology uses erbium/ytterbium fiber optic assemblies (double clad fiber and multi-mode pump lasers) to produce cost effective high power optical amplification. This technology enables the development of higher power EDFAs-something that is cost prohibitive when using standard erbium fiber and single mode pumps. Er/Yb Assembly Er Input Hybrid 980 nm pump Filter / Isolator Isolator Input monitor 1% Tap Output Monitor Multi-mode pumps Drive Electronics Sample FTTx Architecture Splitter OLT Voice ONT ONT ONT ONT 1490nm Businesses Data 1310nm WDM 1550nm Splitter - Voice - Data - Video Splitter ONT ONT ONT ONT 1550nm Tx Video Multi Dwelling Units 20 Km RF Splitter ONT ONT ONT ONT EDFA 20 outputs of 20 dBm Homes 3 of 6 Ortel, a division of EMCORE 2015 West Chestnut Street Alhambra, California 91803-1542 Tel: 626-293-3400 Fax: 626-293-3428 www.emcore.com Copyright 2007. EMCORE Corporation PONA3000 Series High Power EDFA PRELIMINARY DATA SHEET | OCTOBER 28, 2007 Outline Drawing AC and DC versions shown below with 8-port option 4 of 6 Ortel, a division of EMCORE 2015 West Chestnut Street Alhambra, California 91803-1542 Tel: 626-293-3400 Fax: 626-293-3428 www.emcore.com Copyright 2007. EMCORE Corporation PONA3000 Series High Power EDFA PRELIMINARY DATA SHEET | OCTOBER 28, 2007 Laser Safety Information This product meets the applicable requirements of 21 CFR 1010 & 1040 and is classified as a Class IV laser product based on the maximum optical output power shown below. During use as intended, the laser energy is fully contained within the fiber network such that there is no accessible laser radiation and would meet the requirements for a Class I laser product. The laser product report has been submitted to the CDRH and the accession number is expected by October 2006. Wavelength = 1545 ~ 1562 nm (dependant on input source) Maximum Output Power = 3.2 W (single output, 35 dBm model) 5 of 6 Ortel, a division of EMCORE 2015 West Chestnut Street Alhambra, California 91803-1542 Tel: 626-293-3400 Fax: 626-293-3428 www.emcore.com Copyright 2007. EMCORE Corporation PONA3000 Series High Power EDFA PRELIMINARY DATA SHEET | OCTOBER 28, 2007 Ordering Information * PONA30 Power Level - - - Connector Options - - # of Output Ports Class Input Voltage 27: 27 dBm SC: SC/APC 01: 1 port P: Premium AC: 90-260 VAC 50/60 Hz 30: 30 dBm FC: FC/APC 02: 2 ports E: Economy DC: -48 VDC 32: 32 dBm 35: 35 dBm EC: E2000/APC TC: SC/UPC 04: 4 ports 08: 8 ports GC: FC/UPC 16: 16 ports 20: 20 ports 2DC: Redundant DC Class: Premium: Utilizes cooled pump lasers Economy: Utilizes uncooled pump lasers * PONA3000 series with one or two optical outputs will have special high power output optical connector(s) and optical bulkhead(s) For exact model number, please contact your Sales Representative. Qualifications FCC: Subpart B. Part 15, class "A" Unintentional Radiators CE: EN50083-2, 19995 with Amendment 1, which Incorporates EN 55013 Radiated and Conducted Emissions EN 61000-4-3 Radiated Immunity EN 55020 Conducted Immunity EN 61000-3-2 Harmonics All Components Meet Telcordia GR-1312 and GR-486 Standards (Except Pumps in Economy Class). EN 61000-3-2 Harmonics Fit Rate: * 90% Level of Confidence < 2000 @ 30C Premium PONA 3035 * 90% Level of Confidence < 3500 @ 30C Economy PONA 3035 Information contained herein is deemed to be reliable and accurate as of issue date. EMCORE reserves the right to change the design or specifications of the product at any time without notice. Ortel, the Ortel logo, EMCORE, and the EMCORE logo are trademarks of EMCORE Corporation. 6 of 6 Ortel, a division of EMCORE 2015 West Chestnut Street Alhambra, California 91803-1542 Tel: 626-293-3400 Fax: 626-293-3428 www.emcore.com Copyright 2007. EMCORE Corporation