FTR-K1 SERIES ULTRA MINIATURE RELAY 2 POLES - 2 A (Slim Profile Signal Relay) FTR-B4 Series n FEATURES DPDT 2C Ultra miniature slim type relay for surface mounting Height: 9.3 mm maximum (THT) 10 mm maximum (SMT) Weight: Approximately 1.0 g l UL, CSA recognized l Conforms to Telcordia/FCC Part 68 spacing and high breakdown voltage Creepage: 1.6mm Dielectric strength 1.5kV (coil-contact) Surge strength 2.5kV l High reliable birfuracted gold overlay silver contact l Low power consumption 140 mW (standard), 100 mW (latching) l RoHS compliant. Please see page 9 for more information l Plastic sealed l l n PARTNUMBER INFORMATION [Example] FTR-B4 (a) C A (b) (c) 4.5 Z - B05 (d) (e) (f) (a) Relay type FTR-B4 : FTR-B4-Series (b) Terminal type C G S : Through hole : Surface mount : Surface mount, space saving (c) Coil type A B : Standard type : Latching type (1 coil) (d) Coil rated voltage 4.5 : 1.5.....24 VDC Coil rating table at page 3 (e) Contact material Z P : Gold overlay silver nickel (standard) : Gold overlay silver palladium (f) Packaging Nil: B05 : Tube packaging : Tape&Peel packaging (only for surface mount type) Remarks: Actual marking on relay would not carry code FTR and be as below: Ordering code: FTR-B4CA4.5Z Actual marking: B4CA4.5Z 1 FTR-K1 SERIES FTR-B4 SERIES n SPECIFICATION Item Contact Data Life Timing Data Insulation FTR-B4 ( ) A FTR-B4 ( ) B 2 form C Construction Bifurcated contacts Material Z: Gold overlay silver nickel / P: Gold overlay silver palladium Resistance (Initial) Max. 100 m at 1 A, 6 VDC Contact rating (resistive) 30VDC, 1A / 125VAC, 0.3A Max. carrying current 2A Max. switching voltage 250 VAC / 220VDC Max. switching power 62.5VA / 30W Min. switching load * 0.01mA, 10mVDC Mechanical Min. 50 x 106 operations Min. 20 x 106 operations DC load Min. 100 x 103 operations at 1A, 30VDC AC load Min. 100 x 103 operations at 0.3A, 125VAC Rated power 140mW - 230mW 100mW - 130mW Applied pulse width - Min. 10ms Operate power 80mW - 130mW 57mW - 68mW Operating temperature range -40 C to +85 C (no frost) Storage temperature / humidity -40 C to +85 C / 5% to 85% RH (no frost) Operate (at nominal voltage, no bounce) Max. 3 ms Max. 3 ms (set) Release (at nominal voltage, no bounce) Max. 3 ms Max. 3 ms (reset) Resistance (initial) Min. 1,000M at 500VDC Dielectric strength Surge strength Clearance Creepage Other Latching type Configuration Electrical Coil Data Standard type Vibration resistance Shock Open contacts 1,000VAC (50/60Hz) 1min Contacts to coil 1,500VAC (50/60Hz) 1min Adjacent contacts 1,000VAC (50/60Hz) 1min. Coil to contacts 2,500V, 2 x 10s standard wave Adjacent contacts 1.0 mm Open contacts 0.28 mm Coil and contacts 1.0 mm Adjacent contacts 1.0 mm Open contacts 0.28 mm Coil and contacts 1.60 mm Misoperation 10 to 55 to 10Hz at single amplitude 1.65 mm Endurance 10 to 55 to 10Hz at single amplitude 2.5 mm Misoperation 750m/s (11 1ms) Endurance 1,000m/s (6 1ms) Weight Approximately 1 g Sealing RT III (plastic sealed) * Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. 2 FTR-B4 SERIES FTR-K1 SERIES n COIL RATING Standard type Coil Code Rated Coil Voltage (VDC) Coil Resistance +/- 10% (Ohm) Must Operate Voltage (VDC) * Must Release Voltage (VDC) * 1.5 1.5 16.1 1.13 0.15 003 3 64.3 2.25 0.3 4.5 4.5 145 3.38 0.45 006 6 257 4.5 0.6 009 9 579 6.75 0.9 012 12 1,028 9.0 1.2 024 24 2,504 18.0 2.4 Rated Power (mW) 140 230 Latching type (1 coil) Coil Code Rated Coil Voltage (VDC) Coil Resistance +/- 10% (Ohm) Set Voltage (VDC) * Reset Voltage (VDC) * Set/Reset current (mA) 1.5 1.5 22.5 +1.13 -1.13 50 003 3 90 +2.25 -2.25 25 4.5 4.5 203 +3.38 -3.38 17 006 6 360 +4.5 -4.5 13 009 9 810 +6.75 -6.75 8 012 12 1,440 +9.0 -9.0 6 024 24 4,800 +18.0 -18.0 4 Rated Power (mW) 100 120 Note: All values in the table are valid for 20C and zero contact current. * Specified operate values are valid for pulse wave voltage.. n SAFETY STANDARDS Type Compliance Contact rating UL UL 508 Flammability: UL 94-V0 (plastics) E 63615 CSA C22.2 No. 14 LR 40304 0.5A, 125VAC (resistive) 1A, 30VDC 0.3A, 110VDC 2A, 30VDC Comply with Telcordia specifications and FCC part 68 and meet BSI EN60950-1: Marking only for UL, CSA 3 FTR-K1 SERIES FTR-B4 SERIES n CHARACTERISTIC DATA (Reference) l Standard type 4 FTR-K1 SERIES FTR-B4 SERIES l Latching type (1coil) 5 FTR-K1 SERIES FTR-B4 SERIES 6 FTR-K1 SERIES FTR-B4 SERIES n DIMENSIONS FTR-B4C - Through hole type l Dimensions l Schematics (BOTTOM VIEW) l PC board mounting hole layout (BOTTOM VIEW) l Schematics (TOP VIEW) l PC board mounting pad layout (TOP VIEW) l Schematics (TOP VIEW) l PC board mounting pad layout (TOP VIEW) FTR-B4G - Surface mount type l Dimensions FTR-B4S- Space saving type l Dimensions * +/-: Indicates reset state for latching relays (FTR-B4CB, FTR-B4GB and FTR-B4SB versions) Indicates non-operate state for standard relays (FTR-B4CA, FTR-B4GA and FTR-B4SA versions) (+)/(-): Indicates set state for latching relays, operate state for standard relays. Note: Tolerance for PC board mounting hole/pad layout: +/-0.1. Note: Dimensions of the terminals do not include thickness of pre-solder. 7 FTR-K1 SERIES FTR-B4 SERIES n COIL POLARITY LATCHING TYPE Coil terminal 1 8 Set + - Reset - + n RECOMMENDED SOLDERING CONDITIONS FOR SMT (SEE PAGE 9) (TEMPERATURE PROFILE) Notes: 1. Temperature profiles on page 9 show the temperature of PC board surface. 2. Please perform soldering test with your actual PC board before mass production, since the temperatures of PC board surfaces vary according to the size of PC board, status of parts mounting and heating method. n PRECAUTIONS - For details on general precautions, refer to the section on technical descriptions. - Since this is a polarized relay, follow the instructions of the internal wiring diagram for the connections of the coil. - Note that the terminal layout and internal wiring of the surface mount relay are a top view. - Characteristic data is not guaranteed values but measured values of samples from production line. n PACKAGING SPECIFICATIONS l Packaging method l Packaging orientation code: B - Packaging standard: JIS C 0806 - Taping type: TB 2412 - Reel type: R24D - Quantity of 1 reel: 500 pieces l Reel dimensions l Tape dimensions Note: Relays are sold in 500 pieces per box. Minimum order quantity is 1000 pieces for tube packing and 500 pieces for tape & reel packing. 8 FTR-K1 SERIES FTR-B4 SERIES General information 1. ROHS COMPLIANCE l l l All relays produced by Fujitsu Components are compliant with RoHS directive 2011/65/EU including amendments. Use of cadmium in electrical contacts is exempted as per Annex III of the RoHS directive 2011/65/EU. Please consider expiry date of exemption. Relays with cadmium containing contacts are not to be used for new designs. All relays are lead-free. Please refer to Lead-Free Status Info for older date codes at: http://www.fujitsu.com/downloads/MICRO/fcai/relays/lead-free-letter.pdf 2. Recommended Lead Free Solder Condition l l Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has been verified to be compatible with PbSn assembly process. Recommended solder Sn-3.0Ag-0.5Cu. Flow Solder Condition: Pre-heating: maximum 120C within 90 sec. Soldering: dip within 5 sec. at 255C 5C solder bath Relay must be cooled by air immediately after soldering Solder by Soldering Iron: Soldering Iron Temperature: Duration: 30-60W maximum 340-360C maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity l l l l SMT versions of FTR-B4 relays in Tape & Reel package will be shipped in Moisture Barrier Bag(MBB). Moisture Sensitivity Level (MSL) of FTR-B4 relay is indicated on the packing caution label. Relays must be stored in the unopened MBB at storage conditions <40C/90%RH for a maximum 1 year SMT versions of FTR-B4 relays in tube packing will not be shipped in MBB. Therefore, these relays shall be dried by baking before reflow soldering process according to IPC/JEDEC J-STD-033. 4. Tin Whiskers l Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. 9 FTR-K1 SERIES FTR-B4 SERIES Fujitsu Components International Headquarter Offices Japan FUJITSU COMPONENT LIMITED Shinagawa Seaside Park Tower 19F, 12-4, Higashi-shinagawa 4-chome, Shinagawa-ku, Tokyo,140-0002, Japan Tel: (81-3) 3450-1682 Fax: (81-3) 3474-2385 Email: fcl-contact@cs.jp.fujitsu.com Web: www.fujitsu.com/jp/fcl/ Asia Pacific FUJITSU COMPONENTS ASIA, LTD. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcal@sg.fujitsu.com Web: www.fujitsu.com/sg/products/devices/components North and South America FUJITSU COMPONENTS AMERICA, INC 2290 North First Street, Suite 212 San Jose, CA 95131, USA Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: components@us.fujitsu.com Web: us.fujitsu.com/components China FUJITSU ELECTRONIC COMPONENTS (SHANGHAI) CO., LTD. Unit 4306, InterContinental Center 100 Yu Tong Road, Shanghai 200070, China Tel: (86-21) 3253 0998 Fax: (86-21) 3253 0997 Email: fcal@sg.fujitsu.com Web: www.fujitsu.com/sg/products/devices/components Europe FUJITSU COMPONENTS EUROPE B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: www.fujitsu.com/uk/components Hong Kong FUJITSU COMPONENTS HONG KONG CO., LTD Unit 506, Inter-Continental Plaza No.94 Granville Road, Tsim Sha Tsui, Kowloon, Hong Kong Tel: (852) 2881-8495 Tex: (852) 2894-9512 Email: fcal@sg.fujitsu.com Web: www.fujitsu.com/sg/products/devices/components/ Korea FUJITSU COMPONENTS KOREA LIMITED Alpha Tower #403, 645 Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, 13524 Korea Tel: (82) 31-708-7108 Fax: (82) 31-709-7108 Email: fcal@sg.fujitsu.com www.fujitsu.com/sg/products/devices/components/ (c)2017 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users' own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. October 30th, 2017 10